3Pt. 110 & 150 Gallon Sprayers Model 3PT110, 3PT150 Owner's Manual

3Pt. 110 & 150 Gallon Sprayers Model 3PT110, 3PT150 Owner's Manual PaulB LLC 50 Woodcorner Rd. Lititz PA 17543 www.cropcareequipment.com (717) 738-7350 A Paul B Zimmerman Inc. Company

PaulB LLC thanks you for choosing to purchase one of our sprayer models. We appreciate your business and want to personally fill all of your sprayer needs. We also desire to provide you with the technical support and needed parts that will allow you to continue spraying without disruption. See the Contact Us section on page 32. Table of Contents Before You Begin...1 Safety Precautions...2 General Guidelines...2 Before Operation...2 During Operation...3 Following Operation...3 Pump Safety Precautions...3 Mounting the Pump...4 Calibrating the Sprayer...4 Calibration Chart...6 Operating Instructions...7 Boom Spraying...7 Gun Spraying...7 Maintenance Instructions...8 Routine Maintenance...8 Pump Maintenance...8 Winterizing Your Sprayer...9 Warranty...10 Sprayer Breakdowns...11 Boom Breakdowns...17 Suspension System...24 Pump Breakdowns...25 Relief Valve and Control Breakdowns...27 Suction Filter...29 PTO Coupler Breakdown...29 Spray Gun Breakdowns...30 Contact Us...32 Before You Begin Please read and understand this manual and its instructions and warnings completely before operating the sprayer. Be aware of all safety guidelines, warnings, and cautions including those of the tractor manufacturer. Read and understand the chemical manufacturer's labels, warnings, and instructions. Know and fulfill all state pesticide applicator license requirements. Familiarize yourself and other operators with the sprayer's components and how all parts are operated. Page 1

! Safety Precautions! General Guidelines Every year many unnecessary accidents occur due to improper equipment handling and a disregard for safety precautions. You, the operator, can avoid accidents by observing the precautions in this section. The operator should be a responsible adult. Do not allow persons to operate this sprayer until they have displayed a thorough understanding of sprayer safety precautions and operational use! All operators must also fulfill state pesticide applicator license requirements! Never attempt to operate this sprayer when under the influence of alcohol or drugs. The best defense against accidents is a careful and responsible operator. Figure 1: Chemical Warning Decal(# DEMT3980) A chemical warning decal and an owner's manual warning decal are located on the sprayer's tank. Be aware of their location. See Figure 1 and Figure 2. Always replace any warning decals that are not legible or are missing. When transporting the sprayer on public roads, always Figure 2: Owner's Manual Decal(# DE39) follow state and local regulations regarding safety and transportation requirements. Use the necessary lights and slow moving vehicle (SMV) emblems. If there is any portion of this manual that you do not fully understand, please contact PaulB SM. Before Operation Carefully study and understand this owner's manual. Read and follow chemical manufacturer's labels, warnings, and instructions! A material safety data sheet (MSDS) should be provided by the chemical manufacturer. To avoid injury from chemical hazards, wear the proper protective clothing. Each chemical manufacturer's clothing requirements are listed under the Personal Protective Equipment (PPE) section in the chemical instructions. Do not wear loose-fitting clothing which may catch in moving parts. It is also recommended that operators wear suitable hearing and eye protection. Never exceed your tractor's load rating. Page 2

Give the sprayer a visual inspection for any worn parts, loose bolts, or other visible problems, and make the necessary repairs. See the maintenance section (page 8). Make sure the area is clear of any people or obstructions before using the sprayer. Have all operators practice operating the sprayer and its attachments until all persons are completely capable of safe operation. During Operation Always be aware of bystanders, particularly children! Always look before moving the sprayer or engaging the PTO. No passengers are allowed on or in the tractor or sprayer at anytime. Keep hands and body parts clear of all moving parts, especially the tractor PTO. Be aware of dangerous terrain such as holes, slopes, drop-offs, banks, rocks, and hidden hazards. Operate the tractor and sprayer up and down slopes, not across. When operating on inclines, it is especially important that your tractor is equipped with Roll Over Protection System (ROPS). Allow for sprayer boom length when making turns. Never leave running equipment unattended! Remember that accidents can even happen to seasoned operators. Always take your time and follow all safety instructions. Following Operation Following operation, stop the tractor unit, set brakes, disengage PTO, shut off engine, and remove ignition key. Park the sprayer on a hard level surface. Store the sprayer away from human and livestock activity. Do not permit children to play on or around sprayer. Pump Safety Precautions Never pump flammable or explosive fluids such as gasoline, fuel oil, kerosene, etc. Never pump acids (i.e. acid fertilizer) with super rollers. For acid fertilizer Hypro recommends the Silver Series castings with Teflon rollers. Never run the pump dry! Never pump faster or above the maximum recommended speed and pressure (1000 RPM, 200 psi). Never pump liquids at temperatures higher than the recommended maximum temperature (140 F / 60 C) Do not exceed this temperature. Before servicing your pump, disconnect the power, release all pressure, and drain all liquids. Page 3

Mounting the Pump It is important to correctly mount the pump to insure safe pumping operations. The preferred method for mounting the torque arm and the pump to the tractor is with a chain going up to provide support for the pump. 1. Mount the pump and torque arm to the PTO shaft using the correct PTO coupler (included with your pump). When connecting the PTO coupler to the PTO shaft make sure it clicks and is correctly connected. 2. Attach the torque chain to the tractor frame with the torque arm in a horizontal position. The chains should be attached to the tractor as close to vertical as possible to avoid a bending force on the pump. Note: Some tractors do not have easy attachment points for attaching the torque chain. It may be necessary to drill holes in the tractor's master shield to attach the chains. It is also acceptable to mount an angle iron on the master shield to attach the chains. Calibrating the Sprayer Note: All calibration needs to be done with water! When spraying with the boom, the sprayer must be calibrated to ensure proper spray coverage and to combat over-application or under-application. The calibration process is simplified when broken up into the following three steps: 1. Calculate the speed of the tractor. 2. Determine the nozzle size and consult the calibration chart for the desired or instructed Gallon per Acre(GPA). 3. Set the pressure accordingly using the relief valve. 1. Calculating the Speed It is important to to determine what speed your tractor will be traveling at while spraying. While some tractors have speedometers, it is still recommended that speed is calculated for all tractors for accuracy purposes. To determine the speed follow the four following steps Page 4

Measure a 200 foot or 300 foot distance on a field or a surface similar to where you will be spraying. 1. Drive the tractor and sprayer (half-full is optimal) across the measured distance at a Time required(seconds) to travel Speed in MPH a distance of: 200 feet 300 feet constant rate of speed. There can be no 1.0 136 205 changes in speed while you are measuring 1.5 91 136 2.0 68 102 the time. This should be a comfortable 2.5 55 82 speed for spraying. 3.0 45 68 2. Have someone measure the amount of 3.5 39 58 4.0 34 51 time(in seconds) it takes to travel the 4.5 30 45 measured distance. 5.0 27 41 5.5 25 37 3. Your speed can be found by entering your 6.0 23 34 data into the equation Speed(mph) = 6.5 21 31 (Distance(ft) x 60) / (Time(seconds) x 88) 7.0 19 29 or by consulting the table to the left. Note: It is helpful for future references to 2. Determining Nozzle Size and Using Calibration record the exact RPM and gear used to find Chart your speed. The spray nozzles on your sprayer are color-coded to match up with the calibration chart. After you have determined your nozzle size, you need to look at the calibration chart. Using your tractor speed, nozzle size, and desired gallons per acre (GPA), find the pressure (psi) necessary to achieve your GPA. It is important to note that lower pressure settings will result in less spray drift. Example: Assume you have found your tractor speed to be 5 MPH, your nozzles are blue (XRC11003), and you want to spray 15 GPA. Upon looking at the chart, you find that you should set the sprayer's pressure at about 28 psi in order to apply 15 GPA. 3. Adjusting the Pressure on Your Sprayer Note: All calibration needs to be done with clean water! You have found the correct pressure setting, but must now adjust the sprayer to that pressure setting. Before you adjust the sprayer's pressure, it is important to set the tractor's RPM at the rate that was used to find the tractor's speed. The relief valve controls the sprayer's pressure and is located directly beside the pressure gauge. When you go to spray, turn the relief valve until you achieve the necessary pressure. You have successfully calibrated the sprayer! Note: Due to normal wear, Teejet recommends that you replace your sprayer nozzles after every spraying season. Nozzle replacement will ensure accurate spraying performance. Page 5

Calibration Chart Please note: Flow rates are calculated using water. Tip Size PSI GPM Gallons Per Acre of one nozzle 3 MPH 4 MPH 5 MPH 6 MPH 15 20 0.12 0.14 11.8 13.8 8.9 10.4 7.1 8.3 5.9 6.9 XRC11002 30 0.17 16.8 12.6 10.1 8.4 40 0.20 19.8 14.9 11.9 9.9 60 50 0.24 0.22 23.8 21.8 17.8 16.3 14.3 13.1 11.9 10.9 XRC110025 XRC11003 XRC11004 XRC11005 15 20 30 40 50 60 15 20 30 40 50 60 15 20 30 40 50 60 15 20 30 40 50 60 0.15 0.18 0.22 0.25 0.28 0.31 0.18 0.21 0.26 0.30 0.34 0.37 0.24 0.28 0.35 0.40 0.45 0.49 0.31 0.35 0.43 0.50 0.56 0.61 14.8 17.8 21.8 24.8 27.8 30.6 17.8 20.8 25.8 29.8 33.6 36.6 23.8 27.8 34.6 39.6 44.0 48.0 30.6 34.6 42.0 50.0 56.0 60.0 11.1 13.4 16.3 18.6 21.0 23.0 13.4 15.6 19.3 22.0 25.0 27.0 17.8 21.0 26.0 30.0 33.0 36.0 23.0 26.0 32.0 37.0 42.0 45.0 8.9 10.7 13.1 14.9 16.6 18.4 10.7 12.5 15.4 17.8 20.0 22.0 14.3 16.6 21.0 24.0 27.0 29.0 18.4 21.0 26.0 30.0 33.0 36.0 7.4 8.9 10.9 12.4 13.9 15.3 8.9 10.4 12.9 14.9 16.8 18.3 11.9 13.9 17.3 19.8 22.0 24.0 15.3 17.3 21.0 25.0 28.0 30.0 Page 6

Operating Instructions Before operating the sprayer, it is important that you read this entire manual and know all safety precautions. Always take your time and be alert when operating your sprayer. This will allow you to safely spray without accident or interruption. Spraying with the Boom 1. Calibrate the sprayer using the preceding calibration instructions and chart. This will determine what pressure to spray at in order to achieve the desired Gallons per Acre (GPA). 2. Connect the pump's PTO coupler to the PTO shaft (see page 4 for mounting the pump). 3. Fill the tank with some water in order to set the pressure and test for leaks. 4. Prepare the sprayer for spraying by opening the ball valve on the inlet line from the tank, by closing the valve (valves) to the boom supply line, and by making sure the spray gun is closed (only applicable with spray gun option). 5. Start the tractor and engage the pump. The tractor should be running at the RPM rate determined when you calibrated your sprayer. Ensure that the pump is primed and that there are no leaks in any of the lines. 6. Using the relief valve, adjust the sprayer's pressure to the pressure rating found when you calibrated your sprayer. When you open the boom supply line valve (valves) you may need to readjust the pressure. 7. You may now fill the tank with the amount of water and chemicals recommended by the chemical being used. Before filling the tank make sure the tractor's PTO is disengaged. After filling the tank, engage the pump and allow for ample amount of time for the jet agitator to mix the water and chemicals. Note: See chemical instructions for necessary agitation time. You are now ready to begin spraying. 8. Upon arriving at the spraying location, open the booms, engage pump, and make sure the pressure setting is correct. While spraying always remember to maintain a constant level of speed and RPM (rates found when calibrated). Spraying with the Spray Gun 1. Connect the pump's PTO coupler to the PTO shaft (see page 4 for mounting the pump). 2. Fill the tank with some water in order to set the pressure and test for leaks. 3. Make sure the spray gun is closed. 4. Start the tractor and engage the pump. Ensure that the pump is primed and that there are no leaks in any of the lines. Page 7

5. Adjust the sprayer's pressure using the relief valve to your desired setting. When you open the spray gun, you may need to readjust the pressure. 6. You may now fill the tank with the amount of water and chemicals recommended by the chemical being used. Before filling the tank make sure the tractor's PTO is disengaged. After filling the tank, engage the pump and allow for ample amount of time for the jet agitator to mix the water and chemicals. Note: See chemical instructions for necessary agitation time. You are now ready to begin spraying. 7. Upon arriving at the spraying location, engage the pump, and make sure the pressure setting is correct. Turn the knob on the end of the spray gun to adjust the spray pattern. Maintenance Instructions Routine Maintenance It is very important to perform routine maintenance on your sprayer before and after each use. Good maintenance practices will help to guard against any sprayer breakdowns or accidents. 1. It is recommended to perform a visual and physical inspection for any worn parts, loose bolts, or other visible problems. Make all necessary repairs before spraying. See the Contact Us section (page 32) for instructions on ordering parts and getting technical help. 2. After each use it is important to rinse the pump and all components by running water through the system. Rinsing the pump with fresh water will greatly improve the life of the pump! 3. The in-line filter on the inlet supply line should be taken out and rinsed. Note: Be careful not to lose the gasket in the filter bowl. A missing gasket will cause the strainer to leak. 4. Tip strainers should also be taken out and rinsed after every use. Tip strainers are small screens that are located behind each spray nozzle on the boom. Pump Maintenance 1. Follow all pump safety precautions and warnings (page 3). Following these guidelines will help to ensure many years of smooth and trouble-free pumping. 2. Always flush the pump out with fresh water after every use. It is also very important to winterize your pump to prevent freezing and corrosion. See below for winterizing instructions. Page 8

Note: If you have the 6500C or 7700C (cast iron pump), it is recommended that you take the pump off and fill it with oil. This will guard against rust and corrosion. Do not under any circumstances run oil through the sprayer. This will cause hoses to swell up. 3. After many years of use you may find that your pump is leaking or has experienced a decrease in performance. You may need to change the seals and rollers. Contact PaulB for parts, technical assistance, or pump repair. Winterizing your Sprayer To avoid damage from freezing and corrosion, it is important to winterize your sprayer before temperatures grow too cold. 1. Verify that the tank is empty and rinsed out. Dump 1-2 gallons of RV nontoxic antifreeze into the tank. It is not recommended to use standard Antifreeze. Standard antifreeze can be harmful to humans, animals, crops, and the environment. 2. Engage the pump and spray with the boom and subsequently the spray gun (if applicable). Make sure that the antifreeze has been pumped through the entire system including all spray nozzles. 3. Store the sprayer in a dry location away from the elements. 4. Before spraying in the spring it is recommended to flush the sprayer with fresh water to cleanse it of the antifreeze and any other buildup. It would also be beneficial to do a thorough inspection of all sprayer components before spraying. Page 9

PaulB LLC Limited Warranty 3PT Hitch Sprayer: Model 3PT110 & 3PT150 Warranty Coverage PaulB LLC hereby provides a Limited One (1) Year Warranty on the model 3PT110 & 3PT150 sprayer, manufactured by PaulB LLC from the date of original purchase. 3PT110 & 3PT150 sprayers built by PaulB LLC are warrantied against any manufacturer's defects that may occur to any of the sprayer's components in the 12 months following the original date of purchase. This warranty covers the purchaser of this sprayer and any other owners who own it during the one year warranty period. To retain the warranty, the sprayer must be operated and maintained as ascribed by its owner's manual. Warranty is void if: 1. The sprayer has been subjected to, in the opinion of PaulB LLC, negligent handling, misuse, an accident or if the instructions in the owner's manual were not completely followed. 2. The sprayer's components have been altered in any manner or repairs have taken place with unapproved parts. 3. The sprayer and its components were subject to freezing or freezing conditions. The sprayer must have been winterized as per the maintenance instructions to retain the warranty. 4. A non-compatible chemical was used and/or if the sprayer operator failed to rinse all chemical residue out of the sprayer's components after use. 5. A petroleum-based, oil-based, or flammable product was used and caused damage to the pump, tank, hoses, or any other component. Getting Service All sprayer warranty claims must be made through PaulB LLC or an authorized dealer. All warranty claims must be submitted with an invoice or a proof of purchase that denotes the purchase date and place. If you have any questions or comments concerning this warranty, please contact PaulB LLC or an authorized dealer. Page 10

Sprayer Breakdown With 6B Valves Page 11 Left Boom Center Boom Right Boom 28 50 39 46 47 49 40 59 37 33 37 10 63 72 67 52 63 72 88 69 56 76 1 22 36 23 77 58 77 8 6 7 71 66 62 62 51 37 11 44 18 17 42 78 48 38 30 31 14 4 66 62 71 60 34 51 50 21 20 70 61 65 61 70 54 53 32 29 35 45 12 37 72 63 67 72 63 67 72 63 67 75 13 67 68 68 34 67 10 60 60 60 60 34 37 10 15 16 9 20 19 30 57 55 74 32 3 65 43 31 91 47 49 2 5 42 25 28 90 50 48 42 26 27 24 71 62 66 48 50 39 57 61 70 64 70 61 57 B A 89 75

Tank Assembly & Hardware Ref # Qty. Part Number Description 1 1 3PTFRAME150 3PT sprayer frame 2 1 TS3034P Saddle, 110 gallon 2 1 TS3051P Saddle, 150 gallon 3 2 SS30 Tank strap, 2 1/2 W x 59 L 4 1 T503S 6B3 control bracket 4 1 T504S 6B3 with master valve control bracket 5 1 47194 110 gallon, 30 yellow poly tank (includes ref# 6-9) 5 1 47254 150 gallon, 10 yellow poly tank (includes ref# 6-9) 6 1 67399* Tank lid, 10, black 7 1 67400* Threaded tank well, 10, black 8 1 67076* Tank lid tie down strap 9 6 PT10*34S* Tapping screw, #10 x 3/4, stainless steel 10 3 AA6B 6B directo valve control valve 11 1 846034 Relief valve alum/nylon, 3/4 300psi 12 1 2352034PP Poly throttling valve, 3/4 13 1 VHE Extension for master valve (Master valve option only) 14 1 N222166 U-bolt, 5/16 x 2 x 3 1/4 15 1 BAAF Gauge isolator, 1/4 fpt 16 1 GG100 Stainless gauge, liquid filled, 2 1/2, 100 psi 17 1 6500C** Hypro cast iron pump, 6 roller 17 1 6500N** Hypro nitrogen-resistant pump, 6 roller 17 1 6500XL** Hypro silver series pump, 6 roller 17 1 7700C** Hypro cast iron pump, 7 roller 17 1 7700N** Hypro nitrogen-resistant pump, 7 roller 17 1 7700XL** Hypro silver series pump, 7 roller 18 1 13230074 PTO quick connect adapter, 540 RPM, 5/8 shaft 18 1 13230072 PTO quick connect adapter, 540 RPM, 15/16 shaft 19 1 PUMPTA Torque arm for mounting pump 20 2' 0140323 Zinc plated chain, 3/16, system 3 21 1 7601431 Zinc plated snap, open eye bolt 22 1 AA126ML-3-50 Poly strainer, 3/4, sch. 80 23 1 075FP Poly full port ball valve, 3/4 24 1 33710019 Jet agitator 25 1 62798 Poly tank fitting, 3/4, HD, double tap (includes ref# 26-28) 26 1 N/A* Poly nut, 3/4 27 1 N/A* Poly washer, 3/4 28 1 62799* EPDM rubber gasket 29 1 63065* Anti-vortex tank adapter, 1 1/4 (Includes ref# 30-32) 30 2 N/A* Poly nut, 1 1/4 31 2 N/A* Poly washer, 1 1/4 32 2 60404* EPDM rubber gasket 33 1 3F34 Poly pipe plug, 3/4 M.P. 34 3 3F14 Poly pipe plug, 1/4 MNPT 35 1 3M14 Poly pipe nipple, 1/4 x 1/4 * Individual part is included in a complete assembly. ** Pump parts breakdown is listed on page 18. Page 12

Tank Assembly & Hardware Cont. Ref # Qty. Part Number Description 36 1 8M34 Poly nipple, 3/4 x short, sch. 80 37 5 3M34 Poly nipple, 3/4 x 3/4 M.P. 38 1 8M11434 Reducing nipple, 1 1/4 mpt x 3/4 mpt 39 2 3A3434 Poly adapter, 3/4 MNPT x 3/4 barb 40 1 3A3412 Poly adapter, 3/4 MNPT x 1/2 barb 42 3 3EL3434 Poly hose elbow, 3/4 MNPT x 3/4 barb 43 1 3EL34F Poly hose elbow, 3/4 FP x 3/4 hose barb 44 1 8SE34 Poly street elbow, 3/4, sch. 80 45 1 3GTT3414 Poly tee w/ 1/4 guage port, 3/4 46 1 8TT34 Poly tee sch. 80, 3/4 47 2 6806 Stainless hose clamp, 7/16-7/8 48 4 6812 Stainless hose clamp, 1/2-1 1/4 49 N/A 1008 EPDM rubber hose, 1/2 50 N/A 1012 EPDM rubber hose, 3/4 51 4' 3110 Suction hose, 1 52 2 00213* Lift arm pin, category 1-2 (includes ref# 53-54) (3PT110) 52 2 03006* Lift arm pin, category 2 (includes ref# 53-54) (3PT150) 53 2 LW1* Lock washer, 1 (3PT110) 53 2 LW118* Lock washer, 1 1/8 (3PT150) 54 2 NF1* Fine nut, 1 (3PT110) 54 2 NF118* Fine nut, 1 1/8 (3PT150) 55 4 HTB38*4S Stainless hex tap bolt, 3/8 x 4 56 1 H5C38*114 Coarse bolt, 3/8 x 1 1/4, grade 5 57 10 H5C38*1 Coarse bolt, 3/8 x 1, grade 5 58 1 H5C516*1 Coarse bolt, 5/16 x 1, grade 5 59 2 H5C516*34 Coarse bolt, 5/16 x 3/4, grade 5 60 6 H5C14*1 Coarse bolt, 1/4 x 1, grade 5 61 11 LW38 Lock washer 3/8 62 5 LW516 Lock washer 5/16 63 6 LW14 Lock washer 1/4 64 1 EW58 External lock washer, 5/8 65 8 FW38 Flat washer 3/8 66 3 FW516 Flat washer 5/16 67 6 FW14 Flat washer 1/4 68 2 FDW14 Fender washer 1/4 69 8 NC38S Stainless coarse nut 3/8 70 11 NC38 Coarse nut 3/8 71 3 NC516 Coarse nut 5/16 72 6 NC14 Coarse nut 1/4 73 1 075FP Poly full port ball valve, 3/4 (Master valve option only) 74 1 60403* Tank adapter, 1-1/4 (Includes ref# 30-32) 75 1 8RB114100 Poly reducer bushing, 1 x 1-1/4 76 1 3A100114 Poly adapter, 3/4 MP x 1 hose barb 77 2 6816 Stainless steel hose clamp, 1 78 1 3EL34100 Poly hose elbow, 3/4 MP x 1 hose barb 88 2 DE46 Crop Care logo decal 89 1 DE39 Owner's manual warning decal 90 1 DEMT3980 Chemical warning decal 91 1 SP500 Serial number plate S.S. *Individual part is included in a complete assembly. Page 13

Sprayer Breakdown With 17L Valve Page 14 Left Boom Center Boom Right Boom 43 41 41 36 43 36 42 40 35 88 61 49 50 54 62 67 1 21 33 22 71 53 8 6 7 44 39 34 29 30 56 60 64 4 62 54 58 54 57 62 47 46 45 62 54 50 13 11 31 28 12 10 32 14 15 9 29 50 48 23 65 31 3 58 38 30 91 40 42 2 5 37 24 27 90 89 43 41 37 25 26 52 51 71 63 59 55 55 17 16 37 69 41 44 43 20 19 19 18 B A 66

Tank Assembly & Hardware Parts List Ref # Qty. Part Number Description 1 1 3PTFRAME150 3PT sprayer frame 2 1 TS3034P Tank saddle, 110 gallon 2 1 TS3051P Tank saddle, 150 gallon 3 2 SS30 Tank strap, 2 1/2 W x 59 L 4 1 17TMOUNT 17 T-valve mounting bracket 5 1 47194 110 gallon, 30 yellow poly tank (includes ref# 6-9) 5 1 47254 150 gallon, 10 yellow poly tank (includes ref# 6-9) 6 1 67399* Tank lid, 10, black 7 1 67400* Threaded tank well, 10, black 8 1 67076* Tank lide tie down strap 9 6 PT10*34* Tapping screw, #10 x 3/4, stainless steel 10 1 AA17L Tee valve, 3/4 outlets 11 1 2312034PP Poly relief valve, 3/4 12 1 3F14 Poly pipe plug, 1/4 MNPT 13 1 2352034PP Poly throttling valve, 3/4 14 1 BAAF Gauge isolator, 1/4 fpt 15 1 GG100 Stainless gauge, liquid filled, 2 1/2, 100 psi 16 1 6500C Hypro cast iron pump, 6 roller 16 1 6500N Hypro nitrogen-resistant pump, 6 roller 16 1 6500XL Hypro silver series pump, 6 roller 16 1 7700C** Hypro cast iron pump, 7 roller 16 1 7700N** Hypro nitrogen-resistant pump, 7 roller 16 1 7700XL** Hypro silver series pump, 7 roller 17 1 13230074 PTO quick connect adapter, 540 RPM, 5/8 shaft 17 1 13230072 PTO quick connect adapter, 540 RPM, 15/16 shaft 18 1 PUMPTA Torque arm for mounting pump, 12 x 1 x 1 19 2' 0140323 Zinc plated chain, 3/16, system 3 20 1 7601431 Zinc plated snap, open eye bolt 21 1 AA126ML-3-50 Poly strainer, 3/4, sch. 80 22 1 075FP Poly full port ball valve, 3/4 23 1 33710019 Jet agitator 24 1 62798 Poly tank fitting, 3/4, HD, double tap (includes ref# 25-27) 25 1 N/A* Poly nut, 3/4 26 1 N/A* Poly washer 27 1 62799* EPDM rubber gasket 28 1 63065 Anti-vortex tank adapter, 1 1/4 (Includes reft# 29-31) 29 2 N/A* Poly nut, 1 1/4 30 2 N/A* Poly washer 31 2 60404* EPDM rubber gasket 32 1 3M14 Poly pipe nipple, 1/4 MNPT 33 1 8M34 Poly nipple, 3/4 MNPT, sch. 80 34 1 8M11434 Reducing nipple, 1 1/4 MNPT x 3/4 MNPT 35 1 3A3412 Poly adapter, 3/4 MNPT x 1/2 barb * Individual part is included in a complete assembly. Page 15

Tank Assembly & Hardware Cont. Ref # Qty. Part Number Description 36 2 3A3434 Poly adapter, 3/4 MNPT x 3/4 barb 37 3 3EL3434 Poly hose elbow, 3/4 MNPT x 3/4 barb 38 1 3EL34F Poly hose elbow, 3/4 FPT x 1/2 barb 39 1 8SE34 Poly street elbow, 3/4, sch. 80 40 2 6806 Stainless hose clamp, 7/16-7/8 41 4 6812 Stainless hose clamp, 1/2-1 1/4 42 N/A 1008 EPDM rubber hose, 1/2 43 N/A 1012 EPDM rubber hose, 3/4 44 4' 3110 Suction hose, 1 45 2 00213* Lift arm pin, category 1-2 (includes ref# 46-47) (3PT110) 45 2 03006* Lift arm pin, category 2 (includes ref# 46-47) (3PT150) 46 2 LW1* Lock washer, 1 (3PT110) 46 2 LW118* Lock washer, 1 1/8 (3PT150) 47 2 NF1* Fine nut, 1 (3PT110) 47 2 NF118* Fine nut, 1 1/8 (3PT150) 48 4 HTB38*4S Stainless hex tap bolt, 3/8 x 4 49 1 H5C38*114 Coarse bolt, 3/8 x 1 1/4, grade 5 50 10 H5C38*1 Coarse bolt, 3/8 x 1, grade 5 51 1 H5C516*1 Coarse bolt, 5/16 x 1, grade 5 52 2 H5C516*34 Coarse bolt, 5/16 x 3/4, grade 5 53 2 H5C14*1 Coarse bolt, 1/4 x 1, grade 5 54 11 LW38 Lock washer 3/8 55 3 LW516 Lock washer 5/16 56 2 LW14 Lock washer 1/4 57 1 EW58 External lock washer, 5/8 58 8 FW38 Flat washer 3/8 59 1 FW516 Flat washer 5/16 60 2 FW14 Flat washer 1/4 61 8 NC38S* Stainless coarse nut 3/8 62 11 NC38 Coarse nut 3/8 63 1 NC516 Coarse nut 5/16 64 2 NC14 Coarse nut 1/4 65 1 60403* Tank adapter, 1-1/4 (Includes ref# 29-31) 66 1 8RB114100 Poly reducer bushing, 1 x 1-1/4 67 1 3A34100 Poly adapter, 3/4 MNPT x 1 hose barb 69 1 3EL34100 Poly elbow adapter, 3/4 MNPT x 1 hose barb 71 2 6816 Stainless hose clamp, 1 88 2 DE46 Crop Care logo decal 89 1 DE39 Owner's manual warning decal 90 1 DEMT3980 Chemical warning decal 91 1 SP500 Serial number plate S.S. *Individual part is included in a complete assembly. Page 16

12 Ft. Manual Fold Boom Assembly (optional) A 8 Left To Control Valve Boom Center Boom Right Boom 9 25 16 17 16 9 24 B 3 21 4 14 16 17 19 5 10 11 12 13 8 17 16 20" 17 17 16 17 15 8 1 14 4 21 24 18 10 11 12 13 19 5 24 21 23 22 24 6 20 7 16 9 2 Ref # Qty. Part Number Description 1 1 BF1211 Center frame 2 1 BF1212R Right boom wing 3 1 BF1212L Left boom wing 4 2 B126 Boom mounting bracket 5 2 BF1210 Boom mounting clip 6 2 33*TS Extension spring, 1 x 6 7 2 N221267 Zinc eye bolt, 3/8 x 4 8 4 22251311500NYB Nozzle body elbow, 1/2 9 4 22252312500NYB Nozzle body tee, 1/2 10 8 8079PP50 Stainless nozzle screen, 50 mesh, red 11 8 CP19438EPR Seat washer, rubber 12 8 ** Spray nozzle 13 8 ** Nozzle cap 14 8 QJ111SQ114 Nozzle body clamp, 1 1/4, square 15 1 T12 Poly hose barb tee, 1/2 16 N/A 1008 EPDM rubber hose, 1/2 17 18 6806 Stainless hose clamp, 7/16-7/8 18 2 H5C12*5 Course bolt, 1/2 x 5, grade 5 19 4 H5C38*214 Course bolt, 3/8 x 2 1/4, grade 5 20 2 H5C38*2 Course bolt, 3/8 x 2, grade 5 21 6 LW38 Lock washer, 3/8 22 2 FW12 Flat washer, 1/2 23 2 NNC12 Nylon lock Nut, 1/2 24 12 NC38 Course nut, 3/8 25 3 3A1212 Poly adapter, 1/2 MNPT x 1/2 barb **Other tips are available; see page 6 for calibration chart. 24 Page 17

20 Ft. Manual Fold Boom Assembly (optional) 93 98 94 76 99 A 79 Left Boom 88 90 89 88 90 89 B 90 To Control Valve Center Boom Right Boom 88 89 93 90 89 89 91 90 79 94 92 89 90 74 99 77 95 96 97 89 89 90 89 94 95 96 97 77 89 90 92 93 84 85 80 84 83 86 81 82 75 94 Ref # Qty. Part Number Description 74 1 BF2011 Center boom frame 75 1 BF2012R Right boom wing 76 1 BF2012L Left boom wing 77 4 H5C38*214 3/8 x 2 1/4 grade 5 course bolt 79 4 FN38 3/8 flange nut 80 2 H5C12*712 1/2 x 7 1/2 grade 5 course bolt 81 2 FW12 1/2 flat washer 82 2 NNC12 1/2 nylon lock nut 83 2 HTB12*3 1/2 x 3 grade 5 hex tap bolt 84 8 NC38 3/8 course nut 85 2 LW38 3/8 lock washer 86 2 S-267 Extension spring, 1 1/4 x 6 1/2 88 1 3A1212 Poly hose adapter, 1/2 MNPT x 1/2 barb 89 26 6806 Stainless hose clamp, 7/16-7/8 90 N/A 1008 EPDM rubber hose, 1/2 91 1 T12 Hose barb tee, 1/2 92 12 QJ111SQ114 Nozzle body clamp, 1 /14, square 93 4 22251311500NYB Nozzle body elbow, 1/2 94 8 22252312500NYB Nozzle body tee, 1/2 95 12 8079PP50 Stainless nozzle screen, 50 mesh, red 96 12 CP19438EPR Seat washer, rubber 97 12 XRC11003VK ** Ceramic spray tip/cap combination, blue 98 2 CC5520 Poly cap, 1 1/4 square 99 2 B126 Boom mounting bracket **Other tips are available; see page 6 for calibration chart. Page 18

30' Boomless Nozzle Assembly (optional) A 78 B 83 84 85 86 87 75 80 81 76 77 82 83 74 80 82 90 79 81 80 79 81 80 To Control Valve 79 81 80 90 78 84 81 85 82 89 86 81 80 83 75 84 76 77 85 88 86 Ref # Qty. Part Number Description 74 1 T545 Boomless nozzle boom 75 2 CC5520 Poly cap, 1 1/4 square 76 4 H5C38*214 3/8 x 2 1/4 grade 5 course bolt 77 2 BF1210 Boom mounting clip 78 4 FN38 3/8 flange nut 79 1 3A1212 Poly hose adapter, 1/2 MNPT x 1/2 barb 80 12 6806 Stainless hose clamp, 7/16-7/8 81 N/A 1008 EPDM rubber hose, 1/2 82 3 QJ111SQ114 Nozzle body clamp, 1 1/4, square 83 2 22251311500NYB Nozzle body elbow, 1/2 84 3 8079PP50 Stainless nozzle screen, 50 mesh, red 85 3 CP19438EPR * Seat washer, rubber 86 3 QJ4676-90-1/4-NYR QuickJet adapter, 90 deg., 1/4 fpt (includes ref. # 88) 87 1 1/4XP20L-VP XP BoomJet nozzle, left, poly 88 1 1/4XP20R-VP XP BoomJet nozzle, right, poly 89 1 1/4TTJ08-VS Turbo TurfJet, 1/4 fpt, white 90 2 B126 Boom mounting bracket * Individual part is included in a complete assembly Page 19

30 Ft. Boom Assembly (optional) 20 18 44 21 37 44 17 35 38 42 14 3 22 19 1 16 35 38 42 A 38 42 14 2 Left Boom To Control Valve Center Boom Right Boom 8 6 5 4 42 19 B 20 22 24 42 21 7 9 34 40 35 24 31 32 10 45 31 32 5 4 38 42 33 41 24 32 41 30 20" 13 32 24 29 40 35 11 31 32 24 24 12 25 32 31 26 27 28 24 20" 11 24 43 39 15 36 24 23 Page 20

30 Ft. Boom Assembly (optional) Ref # Qty. Part Number Description 1 1 BF4013L Left vertical boom support 2 1 BF4013R Right vertical boom support 3 1 B101 Top boom support 4 2 B103 Boom clip 5 2 B104 Boom clip spacer 6 1 B105L Left boom hinge 7 1 B105R Right boom hinge 8 1 B106L Left boom 9 1 B106R Right boom 10 1 B107 Center boom 11 4 B108 Spring cap 12 2 B109 1 3/4 OD x 8 long spring 13 2 B110 Hose holder 14 2 B111 Boom rest 15 2 B112 Rope clip 16 1 SMVS SMV socket 17 1 SMVB SMV spade 18 1 SMVP Plastic SMV sign 19 2 TS15 15 tarp strap 20 2 N273433 2 1/2 S-hook 21 2 N273425 2 S-hook 22 2 F348 Support rope 23 4 22251311500NYB Nozzle body elbow, 1/2 24 14 22252312500NYB Nozzle body tee, 1/2 25 18 8079PP50 Stainless nozzle screen, 50 mesh, red 26 18 CP19438EPR Seat washer, rubber 27 18 ** Spray nozzle 28 18 ** Nozzle cap 29 18 QJ11134 Nozzle body clamp, 3/4 round 30 1 T12 Poly hose barb tee, 1/2 31 N/A 1008 EPDM rubber hose, 1/2 32 38 6806 Stainless hose clamp, 7/16-7/8 33 2 H5C12*12 Coarse bolt, 1/2 x 12, grade 5 34 2 H5C12*112 Coarse bolt, 1/2 x 1 1/2, grade 5 35 6 H5C38*114 Coarse bolt, 3/8 x 1 1/4, grade 5 36 2 H5C516*2 Coarse bolt, 5/16 x 2, grade 5 37 2 SBR14*34 Stove bolt, 1/4 x 3/4 38 4 LW38 Lock washer, 3/8 39 2 LW516 Lock washer, 5/16 40 4 FW38 Flat washer, 3/8 41 4 NNC12 Nylon nut coarse, 1/2 42 6 NC38 Nut coarse, 3/8 43 2 NC516 Nut coarse, 5/16 44 2 NC14 Nut coarse, 1/4 45 3 3A1212 Poly adapter, 1/2 MNPT x 1/2 barb **Other tips are available; see page 6 for calibration chart. Page 21

35ft Boom Assembly (optional) 21 22 21 19 47 41 18 22 23 38 42 46 3 23 20 14 1 17 38 42 46 A 42 46 14 2 Left To Control Valve Boom Center Boom Right Boom 21 8 6 24 5 4 46 20 B 21 22 46 7 33 9 45 37 25 25 39 44 30 25 33 31 33 32 33 10 44 39 25 48 32 33 5 42 46 4 45 13 11 12 22 32 33 25 26 33 32 27 28 29 25 25 24 11 20" 25 25 15 40 23 16 25 43 47 44 46 21 44 38 35 21 34 Page 22

35ft Boom Assembly (optional) Ref # Qty. Part Number Description 1 1 BF4013L Left vertical boom support 2 1 BF4013R Right vertical boom support 3 1 B120 Top boom support 4 2 B103 Boom clip 5 2 B104 Boom clip spacer 6 1 B105L Left boom hinge 7 1 B105R Right boom hinge 8 1 B122 Left boom 9 1 B123 Right boom 10 1 B121 Center boom 11 4 B108 Spring cap 12 2 B109 1 3/4 OD x 8 long spring 13 2 B110 Hose holder 14 2 B111 Boom rest 15 2 B124 Flip out boom 16 2 F520 Drop tube holder (optional) 17 1 SMVS SMV socket 18 1 SMVB SMV spade 19 1 SMVP Plastic SMV sign 20 2 TS15 15 tarp strap 21 8 N273433 2 1/2 S-hook 22 4 N273425 2 S-hook 23 4 F348 Support rope 24 6 22251311750NYB Nozzle body elbow, 3/4 25 15 22252312750NYB Nozzle body tee, 3/4 26 21 8079PP50 Stainless nozzle screen, 50 mesh, red 27 21 CP19438EPR Seat washer, rubber 28 21 ** Spray nozzle 29 21 ** Nozzle cap 30 21 QJ1111 Nozzle body clamp, 1 round 31 3 T34 Poly hose barb tee, 1/2 32 N/A 1012 EPDM rubber hose, 3/4 33 48 6812 Stainless hose clamp, 3/4 34 2 CP38*212 Clevis pin, 3/8 x 2 1/2 35 2 CP212 Clip pin 36 2 H5C12*12 Coarse bolt, 1/2 x 12, grade 5 37 2 H5C12*112 Coarse bolt, 1/2 x 1 1/2, grade 5 38 4 H5C38*212 Coarse bolt, 3/8 x 2 1/2, grade 5 39 4 H5C38*114 Coarse bolt, 3/8 x 1 1/4, grade 5 40 2 H5C14*2 Coarse bolt, 1/4 x 2, grade 5 41 2 SBR14*34 Stove bolt, 1/4 x 3/4 42 4 LW38 Lock washer, 3/8 43 2 LW14 Lock washer, 1/4 44 8 FW38 Flat washer, 3/8 45 4 NNC12 Nylon nut coarse, 1/2 46 8 NC38 Nut coarse, 3/8 47 4 NC14 Nut coarse, 1/4 48 3 3A1234 Poly adapter, 1/2 MNPT x 3/4 barb *Individual part is included in a complete assembly. **Other tips are available; see page 6 for calibration chart. Page 23

Optional Boom Suspension System For 30' and 35' Booms Ref# Qty Part# Description Ref# Qty Part# Description 1 2 CT18*1 1/8 x 1 cotter pin 12 10 NC58 5/8 NC nut 2 2 CP38*114 3/8 x 1-1/4 clevis pin 13 10 LW58 5/8 lock washer 3 2 P27084 3/8 NF clevis rod end 14 1 BS800S2 Sway link 4 2 NF38 3/8 NF nut 15 2 B116 Extension spring 1-1/2 x 9-1/2 5 4 Part of ref #8 Washer 16 2 N221267 3/8 x 4 eye bolt 6 2 Part of ref #8 Rubber bushing 17 28 NC38 3/8 NC nut 7 2 SC200 Shock cover 18 32 LW38 3/8 lock washer 8 2 48569 Shock absorber 19 4 LW516 5/16 lock washer 9 4 H5C516*114 5/16 x 1-1/4 bolt 20 4 NC516 5/16 NC nut 10 4 FW516 5/16 flat washer 21 1 BS800S4 Shock frame front 11 4 BS800S1 Shock link 22 1 BS800S3 Shock frame rear Page 24

Hypro 6500C, 6500N, 6500XL Pumps Parts Breakdown Page 25

Page 26 Hypro 7700C, 7700N, 7700XL Pumps Parts Breakdown

23120 Relief Valve Used With 17L Valve Parts Breakdown Ref # Qty Part Number Description 1 1 CP23122-NY Nylon adjusting cap 2 1 CP23124-PP Polypropylene spring retainer 3* 1 CP23126-302SS Stainless retaining pin 4* 1 CP7717-15-EPR EPDM rubber O-ring 5* 1 CP23127-302SS Stainless spring 6 1 CP23125-PP Polypropylene guide seat 7 1 CP23123-PP Poly lock ring 8 1 CP23128-PP Polypropylene body, 1/2 MNPT * 1 PK-AB23120-KIT Spare parts kit (includes ref # 3,4,5) 17L Control Valve Parts Breakdown Page 27

8460 Relief Valve Used With 6B Valves Parts Breakdown 6B Control Valve Parts Breakdown Page 28

AA126ML-3-50 Suction Filter 1323-0074 PTO Coupler 5/8 shaft 1323-0072 PTO Coupler 15/16 shaft Parts Breakdown Qty. Part Number Description 1 1400-0024 Poly sleeve, quick coupler 1 1810-0037 Snap ring 1 1900-0160 Compression spring 3 3250-0030 Locking ball 1 34100038 Adapter kit 1 6031-0140 Warning decal Page 29

Spraying Systems Spray Gun Parts Breakdown Ref # Qty Part Number Description 1 1 CP1325 Brass cap 2 1 D6* Hardened stainless orifice disc, #6 3 1 CP5871-BU Buna-N tip gasket 4 1 CP5869 Brass spray housing 5 1 10516 Brass core body 6 1 CP5872 Brass guide sleeve 7 2 CP45197-NYB Nylon gasket 8 1 CP5798-NY Nylon seat plate 9 1 CP7985 Brass washer 10 1 CP6022 Brass stem 11 1 CP6021 Brass tubing 12 1 CP6618 Brass nut 13 1 CP5866-12/GH Brass inlet body, garden hose 14 1 CP5882 Brass hand grip stud 15 1 CP5883 Brass packing washer 16 4 CP5809-LEA Leather packing washer 17 1 CP5811 Brass packing screw 18 1 CP5808-POL Polyethylene garden hose gasket 19 1 CP5884-INP Steel-nickel plated hand grip collar 20 1 CP5994-2-NY Nylon hand grip 21 1 CP5813 Brass hand grip nut Kit 1 5838 Handle grip assembly (includes ref# 14,19,20,21) Kit 1 PK-AB18-KIT Spare parts kit (includes ref# 3,5,8,9) *Hardened stainless steel orifice discs are available in other sizes. Page 30

Hypro Pistol-Grip Spray Gun Parts Breakdown Ref. No Qty. Qty. Part Number Description Ref. No Req'd Req'd Part Number Description Spray nozzles: 16 1 9920-29208-131 Gun body 1 1 3385 3385-2300, -3000, 17* 1 9920-29902-8 Plastic Trigger -3500, -4000, 18 1 9920-291607-3 Pin -4500, -5000, -5500, -6000, -7000 2 1 N/A O-ring 19 1 9920-291702-26 Plug 3 1 9920-261701-10 Nozzle holder 20*/** 1 9920-291003-24 Spring 4* 1 9920-68602-10 O-ring 21*/** 1 9920-23602-37 O-ring 5* 1 9920-261707-2 Nozzle protector 22*/** 1 N/A separately Seat 6 1 9920-26605-50 Locking ferrule 23*/** 1 N/A separately Valve retainer 7 1 9920-261703-69 Barrel 24*/** 1 9920-23602-36 O-ring 8 1 N/A Stream straightener 25 1 9920-231304-29 Pin 9* 1 9920-261304-33 Valve 26*/** 1 9920-23601-35 Gasket 10* 2 9920-71602-6 O-ring 27 1 9920-231003-16 Spring 11 1 9920-26305-3 Valve body 28 1 9920-29507-10 Clip 12 1 9920-261506-14 Spacer 29 1 9920-291101-1 Nipple 13* 1 9920-26902-6 Adjusting lever 30 1 9920-261502-45 Swivel connection 14 1 9920-261902-20 Screw Hose barb, wing nut, 31 1 9920-162604-17 15 1 9920-26801-5 Ferrule insert gasket *Gun Repair Kit # 3430-0460 includes: Ref # 4, 5, 9, 10, 13, 17, 20, 21, 22, 23, 24, 2 ** Trigger Valve Repair Kit # 3430-0460 includes: Ref # 20, 21, 22, 23, 24, 26 Page 31

Contact Us We desire to give you continuing service in the best manner possible. This includes listening to your comments, suggestions, and problems. We will do our best to answer all questions thoroughly and in a timely manner. We have trained sprayer technicians who are more than willing to listen to any questions or problems and help you to find a feasible solution. Ordering Parts We have a fully-stocked parts department that will be able to meet all of your parts needs. Our trained salespersons will ensure that all purchases are processed smoothly and shipped in a timely manner. Our hardware store also has a plumbing, electrical, automotive, paint, lawn & garden, and a power tool department. We are set up to ship our products via UPS and would be glad to work with you on the best shipping solution. If you desperately need a part, we are able ship UPS Next Day Air for many locations. Note: When ordering parts, please provide our sales staff with the correct part number and description listed on the parts list. To directly reach our parts department, please call (717) 738-7355 ext 2000. PaulB LLC A Paul B Zimmerman Inc. Company 50 Woodcorner Road Lititz PA 17543 Parts Dept (717) 738-7355 ext 2000 Corporate Office (717) 738-7350 Fax (717) 738-8061 www.cropcareequipment.com TM Page 32

Form OM0026 08/07