REFRIGERATION HEAT EXCHANGERS SWEP COMPACT BRAZED HEAT EXCHANGERS (CBE s) Maximum Material Efficiency No dead zone outside gaskets because there is no need for gaskets. Up to 25% more capacity utilization than PHEs (gasketed, plate-and-frame heat exchangers), and up to ten times more than shell-and-tubes! Small Hold-up Volumes The compact system uses only a fraction of the heat transfer medium, e.g. refrigerant. Less volume costs less and is positive for the environment. Lower System Costs Better heat transfer coefficient (HTC) gives better T (temperature difference), which in turn means a lower mass flow of media, resulting in smaller, less expensive pumps, etc. and lower energy consumption. Small Temperature Difference Operates efficiently even at temperature differences as low as 1k. High Working Pressure No problem even if you have high pressure. Our CBEs are tested at 1.5 times the maximum operating pressure rating. Low Pressure Drop In most cases lower than any other system. Allows smaller pumps and lower operating costs. True Counter-Current Flow Allows close temperature approach. Self-Cleaning Thanks to high turbulence throughout the exchanger. Boosts up time and cuts costs. Uniform High Quality Plates are pressed in the same tool, brazed in the same automated procedure with rigorous standards of quality control. Performance is known and consistent. Maintenance and repair minimized. Overall Economy High-volume, automated production, easy assembly, low operating costs and excellent heat transfer. The bottom line: outstanding performance and a short payback time. P4157 871
REFRIGERATION HEAT EXCHANGERS SWEP COMPACT BRAZED HEAT EXCHANGERS Application: EVAPORATORS REFRIGERANT WATER-NPT PART WIDTH LENGTH DEPTH NET MODEL TONS In (F3) Out (F1) (F2 & F4) NUMBER (in.) (in.) (in.) WEIGHT I.D. (in.) I.D. (in.) I.D. (in.) SW10650-016 B8 E 1/2 1/2 2.8 12.2 1.6 5/8 7/8 3/4 4.5 SW10650-020 B8 E 3/4 3/4 2.8 12.2 1.9 5/8 7/8 3/4 5.1 SW10650-024 B8 E 1/2 1 2.8 12.2 2.3 5/8 7/8 3/4 5.7 SW10651-016 B15 E 1-1/2 1-1/2 2.8 18.3 1.6 5/8 7/8 3/4 6.6 SW10651-020 B15 E 2 2 2.8 18.3 1.9 5/8 7/8 3/4 7.5 SW10651-024 B15 E 2-1/2 2-1/2 2.8 18.3 2.3 5/8 7/8 3/4 8.5 SW11510-020 B25 E 3 3 4.6 20.6 2.0 7/8 7/8 1 15.8 SW11510-020 B25 E 3-1/2 3-1/2 4.6 20.6 2.0 7/8 7/8 1 15.8 SW11510-024 B25 E 4 4 4.6 20.6 2.4 7/8 7/8 1 17.9 SW10152-030 B25 E 5 5 4.6 20.6 2.9 1-1/8 1-1/8 1 21.0 SW10152-044 B25 E 7-1/2 7-1/2 4.6 20.6 4.2 1-1/8 1-1/8 1 28.2 SW10308-026 B45 E 10 10 9.5 20.6 2.8 1-3/8 1-3/8 1-1/2 36.6 SW10308-032 B45 E 12-1/2 12-1/2 9.5 20.6 3.4 1-3/8 1-3/8 1-1/2 42.3 SW10308-040 B45 E 15 15 9.5 20.6 4.1 1-3/8 1-3/8 1-1/2 49.8 SW11057-054 V45 E 20* 20 9.5 20.6 5.5 1-1/8 1-5/8 2 65.4 SW11057-070 V45 E 25* 25 9.5 20.6 7.0 1-1/8 1-5/8 2 81.1 SW11057-080 V45 E 30* 30 9.5 20.6 7.9 1-1/8 1-5/8 2 91.0 SW11727-090 V57E 40 40 9.6 27.3 9.2 1-3/8 2-5/8 2-1/2 164.3 SW11727-110 V57E 50 50 9.6 27.3 11.2 1-3/8 2-5/8 2-1/2 192.9 SW11727-140 V57E 60 60 9.6 27.3 14.0 1-3/8 2-5/8 2-1/2 235.9 SW11727-160 V57E 70 70 9.6 27.3 16.0 1-3/8 2-5/8 2-1/2 264.6 SW11727-200 V57E 80 80 9.6 27.3 19.8 1-3/8 2-5/8 2-1/2 321.9 SW11727-220 V57E 90 90 9.6 27.3 21.7 1-3/8 2-5/8 2-1/2 350.6 SW10676-150 V65E 100** 100 14.3 34.0 14.4 3 4-1/2 4-1/2 490.6 SW10676-180 V65E 110** 110 14.3 34.0 17.1 3 4-1/2 4-1/2 563.4 SW10676-180 V65E 120** 120 14.3 34.0 17.1 3 4-1/2 4-1/2 563.4 NOTES: Nominal Tons 12,000 Btu. Conditions 54 F EWT, 44 HF LWT, 35 F Evaporating Temp, 9 F Superheat, 2.4 Gpm per ton, R-22. For other conditions call the Totaline Commercial Refrigeration Hotline. Various connection executions are possible, please get in touch with RCD Commercial Refrigeration. *These units have a 22 psi pressure drop across the evaporating refrigerant side, can be reduced, consult RCD. **These have a 15 psi pressure drop, as above. 872
REFRIGERATION HEAT EXCHANGERS SWEP COMPACT BRAZED HEAT EXCHANGERS Application: CONDENSERS REFRIGERANT WATER-NPT PART WIDTH LENGTH DEPTH NET MODEL TONS In (F1) Out (F3) (F4 & F2) NUMBER (in.) (in.) (in.) WEIGHT I.D. (in.) I.D. (in.) I.D. (in.) SW10010-010 B8 CD 1/2 1/2 2.8 12.2 1.1 7/8 7/8 3/4 3.5 SW10010-016 B8 CD 3/4 3/4 2.8 12.2 1.6 7/8 7/8 3/4 4.5 SW10010-016 B8 CD 1 1 2.8 12.2 1.6 7/8 7/8 3/4 4.5 SW10010-020 B8 CD 1-1/2 1-1/2 2.8 12.2 1.9 7/8 7/8 3/4 5.1 SW10010-024 B8 CD 2 2 2.8 12.2 2.3 7/8 7/8 3/4 8.5 SW10010-030 B8 CD 2-1/2 2-1/2 2.8 12.2 2.8 7/8 7/8 3/4 9.9 SW10039-020 B15 CD 3/4 3 2.8 18.3 1.9 7/8 7/8 3/4 7.5 SW10039-026 B25 E 3-1/2 3/12 2.8 18.3 2.5 7/8 7/8 3/4 8.9 SW10039-026 B15 CD 4 4 2.8 18.3 2.5 7/8 7/8 3/4 8.9 SW10039-040 B15 CD 5 5 2.8 18.3 3.7 7/8 7/8 3/4 12.2 SW10961-030 B27 CD 7-1/2 7-1/2 4.7 20.7 2.9 1-3/8 1-3/8 1-1/4 19.4 SW10961-040 B27 CD 10 10 4.7 20.7 3.9 1-3/8 1-3/8 1-1/4 24.3 SW10961-050 B27 CD 12-1/2 12-1/2 4.7 20.7 4.8 1-3/8 1-3/8 1-1/4 29.3 SW10961-060 B27 CD 15 15 4.7 20.7 5.7 1-3/8 1-3/8 1-1/4 34.3 SW10175-040 B45 CD 20 20 9.5 20.6 4.1 1-5/8 1-5/8 1-1/2 49.8 SW11751-050 B57 CD 30 30 12.0 27.3 5.2 2-5/8 2-5/8 2-1/2 77.6 SW11751-070 B57 CD 40 40 12.0 27.3 7.1 2-5/8 2-5/8 2-1/2 96.3 SW11751-080 B57 CD 50 50 12.0 27.3 8.0 2-5/8 2-5/8 2-1/2 105.7 SW11751-100 B57 CD 60 60 12.0 27.3 7.1 2-5/8 2-5/8 2-1/2 124.4 SW11751-120 B57 CD 70 70 12.0 27.3 11.6 2-5/8 2-5/8 2-1/2 143.1 SW11751-140 B57 CD 80 80 12.0 27.3 13.5 2-5/8 2-5/8 2-1/2 161.8 SW11751-160 B57 CD 90 90 12.0 27.3 15.3 2-5/8 2-5/8 2-1/2 180.5 SW11751-180 B57 CD 100 100 12.0 27.3 17.1 2-5/8 2-5/8 2-1/2 199.2 SW11751-200 B57 CD 110 110 12.0 27.3 18.9 2-5/8 2-5/8 2-1/2 217.9 SW11751-220 B57 CD 120 120 12.0 27.3 20.8 2-5/8 2-5/8 2-1/2 236.6 NOTES: Nominal Tons 15,000 Btu/h. Conditions 85 F EWT, 105 F Condensing Temp, 3.5 F Sub-Cooling, 3 Gpm per ton, R-22. For other conditions call the Totaline Commercial Refrigeration Hotline. Various connection executions are possible, please get in touch with RCD Commercial Refrigeration. 873
REFRIGERATION HEAT EXCHANGERS SWEP COMPACT BRAZED HEAT EXCHANGERS Application: SUBCOOLERS ECONOMIZERS REFRIGERANT WATER-NPT PART WIDTH LENGTH DEPTH NET MODEL TONS In (F3) Out (F1) (F2 & F4) NUMBER (in.) (in.) (in.) WEIGHT I.D. (in.) I.D. (in.) I.D. (in.) SW10014-016 B8 SE 2 2 2.80 12.20 1.60 7/8 7/8 7/8 4.50 SW10015-016 B10 SE 3 3 4.6 11.3 1.7 7/8 7/8 7/8 7.8 SW10015-026 B10 SE 5 5 4.6 11.3 2.6 7/8 1-1/8 1-1/8 10.5 SW11142-020 B27 SE 7 7 4.6 20.7 2.0 7/8 1-1/8 1-1/8 12.4 SW10863-026 B27 SE 10 10 4.6 20.7 2.6 7/8 1-3/8 1-3/8 17.4 SW10863-030 B27 SE 12 12 4.6 20.7 2.9 7/8 1-3/8 1-3/8 19.4 SW11730-036 B27 SE 14 14 4.6 20.7 3.5 7/8 1-5/8 1-5/8 22.3 SW11731-040 B27 SE 16 16 4.6 20.7 3.9 1-3/8 1-5/8 1-5/8 24.3 SW11733-026 B45 SE 18 18 9.5 20.7 2.8 1-3/8 1-5/8 2-1/8 36.6 SW11733-030 B48 SE 20 20 9.5 20.7 3.2 1-3/8 1-5/8 2-1/8 40.4 SW11733-034 B48 SE 22 22 9.5 20.7 3.6 1-3/8 1-5/8 2-1/8 44.1 SW11732-040 B48 SE 28 28 9.5 20.7 4.1 1-3/8 2-1/8 2-1/8 49.8 NOTES: Nominal Tons 12,000 Btu/h. Liquid refrigerant subcooled from 110 F to 50 F, Evaporating Temp 35 F, Superheat 9 F, per Ton. For other conditions run unit performance calculation on SSP. Pressure drop across the liquid side of the subcoolers is less than 3.75 psi for all selections. 874
REFRIGERANT HEAT EXCHANGERS REFRIGERANT HEAT EXCHANGERS FOR USE WITH TOTALINE UNIT COOLER MODELS HEAT EXCHANGER CAPACITY GUIDE CAPACITY RATINGS (BTUH) HEAT EXCHANGER FREEZER COOLER MFG. P/N P/N 5,500 8,500 HXR-50 8354018 7,500 15,000 HXR-75 8354019 10,000 17,500 HXR-100 8354020 15,000 25,000 HXR-150 8354021 25,000 43,000 HXR-250 8354022 32,500 65,000 HXR-350 8354023 61,200 85,000 HXR-500 8354024 73,000 120,000 LHXR-15 8354030 93,000 164,400 LHXR-20 8354031 118,000 208,800 LHXR-25 8354032 141,000 246,000 LHXR-30 8354033 166,000 288,000 LHXR-35 8354034 COAXIAL DESIGN FOR OPTIMUM HEAT TRANSFER. FOR FREEZER CAPACITY: 5500 TO 166,000 BTUs. FOR COOLER CAPACITY: 8500 TO 288,000 BTUs. U.L. RECOGNIZED. COPPER REFRIGERANT CONNECTION. MODELS: 8354018 THRU 8354024 HAVE A COPPER SHELL AND RED BRASS INNER TUBE. MODELS: 8354030 THRU 8354034 HAVE A STEEL SHELL AND A STAINLESS STEEL INNER TUBE. 875
REFRIGERANT HEAT EXCHANGERS REFRIGERANT HEAT EXCHANGERS HXR & LHXR SERIES DIMENSIONAL DATA E A I.D. F H B I.D. G J D C J DIAGRAM #1: HXR SERIES HEAT EXCHANGERS D A I.D. L F I.D. B G H J K E C A I.D. DIAGRAM #2: LHXR SERIES HEAT EXCHANGERS SEE DIA. # 1 2 DIMENSIONS (IN INCHES) HEAT EXCHANGER A B C D E F G H J K L MFG. P/N P/N 3/8 5/8 12-3/4 11 13 1-5/8 7/8 2-5/16 7/8 - - HXR-50 8354018 3/8 7/8 13-5/8 11 13 1-3/4 1-1/8 2-9/16 1-5/16 - - HXR-75 8354019 3/8 1-1/8 14-1/8 11 12-3/4 1-7/8 1-3/8 2-13/16 1-9/16 - - HXR-100 8354020 1/2 1-1/8 14-1/8 11 13-3/4 2 1-3/8 3 1-9/16 - - HXR-150 8354021 5/8 1-3/8 14-1/4 11 14-1/4 2-3/8 1-5/8 3-9/16 1-5/8 - - HXR-250 8354022 5/8 1-5/8 16-1/4 12 15-1/4 2-3/8 1-5/8 3-9/16 2-1/8 - - HXR-350 8354023 7/8 2-1/8 17-1/4 12 13 2-15/16 2-5/8 4-5/8 2-5/8 - - HXR-500 8354024 7/8 2-1/8 29-1/2 24 21-3/8 3-7/16 2-7/8 6-7/8 2-3/4 1-5/16 2 LHXR-15 8354030 1-1/8 2-1/8 29-1/2 24 21-3/8 3-7/16 2-7/8 6-7/8 2-3/4 1-5/16 2 LHXR-20 8354031 1-1/8 2-5/8 38 32-1/2 29-3/4 3-3/4 3-1/2 7-1/2 2-3/4 1-3/8 2 LHXR-25 8354032 1-3/8 2-5/8 38 32-1/2 29-3/4 4 3-1/2 8 2-3/4 1-3/8 2-1/4 LHXR-30 8354033 1-3/8 2-5/8 40-1/8 34-5/8 31-7/8 4 3-1/2 8 2-3/4 1-3/8 2-1/4 LHXR-35 8354034 876
REZNOR HEAT EXCHANGERS REFRIGERANT HEAT EXCHANGERS MODEL NUMBER TYPE AL TYPE 409 S.S. TYPE 321 S.S. P/N P/N P/N (H,C)X 50 REZ-9962 REZ-19427 N/A (H,C)X 75 & 100 REZ-9895 REZ-19429 REZ-19438 (H,C)X 125 REZ-9855 REZ-19430 REZ-19439 (H,C)X 150 & 175 REZ-9817 REZ-19431 REZ-19440 (H,C)X 200 & 225 REZ-9779 REZ-19432 REZ-19441 (H,C)X 250 & 300 REZ-9743 REZ-19433 REZ-19442 (H,C)X 350 REZ-9707 REZ-19434 REZ-19443 (H,C)X 400 REZ-9514 REZ-19435 REZ-19444 F,B,FE & BE25 REZ-102282 REZ-102311 N/A F,B,FE & BE50 REZ-102283 REZ-102312 N/A F,B,FE & BE75 REZ-102284 REZ-102313 N/A F,B,FE & BE100 REZ-102285 REZ-102314 N/A F,B,FE & BE130 REZ-102286 REZ-102315 N/A F,B,FE & BE165 REZ-102287 REZ-102316 N/A F,B,FE & BE200 REZ-102288 REZ-102317 N/A F,B,FE & BE250 REZ-102289 REZ-102318 N/A F,B,FE & BE300 REZ-102290 REZ-102319 N/A F,B,FE & BE400 REZ-102291 REZ-102320 N/A (H,C)R,SC(G,P,X) 75 & 100 REZ-44301 REZ-44302 REZ-44303 (H,C)R,SC(G,P,X) 125 REZ-44304 REZ-44305 REZ-44306 (H,C)R,SC(G,P,X) 150 &175 REZ-44307 REZ-44308 REZ-44309 (H,C)R,SC(G,P,X) 200 & 225 REZ-44310 REZ-44311 REZ-44312 (H,C)R,SC(G,P,X) 250 & 300 REZ-44313 REZ-44314 REZ-44315 (H,C)R,SC(G,P,X) 350 REZ-44316 REZ-44317 REZ-44318 (H,C)R,SC(G,P,X) 400 REZ-44319 REZ-44320 REZ-44321 Type AL, 409 S.S., & 321 S.S. differ only by material composition. Catalogs & Price Pages available upon request. Entire line of Reznor parts available under P/N s REZ-nnn. 877
REFRIGERATION MOTORS UNIT BEARING MOTORS P162 CAST IRON, SHADED POLE DIMENSIONS (in.) WATTS VOLTS AMPS RPM ROT B C P/N 2.5W 115 0.3 1000 CW 2.8 3.3 GE-5111 4W 115 0.3 1550 CW 2.8 3.3 GE-5211 4W 115 0.3 1550 CCW 2.8 3.3 GE-5212 4W 230 0.2 1550 CW 2.8 3.3 GE-5221 4W 230 0.2 1550 CCW 2.8 3.3 GE-5222 6W 115 0.4 1550 CW 3.3 3.8 GE-5311 6W 115 0.4 1550 CCW 3.3 3.8 GE-5312 9W 115 0.6 1550 CW 3.3 3.8 GE-5411 9W 115 0.6 1550 CCW 3.3 3.8 GE-5412 9W 230 0.3 1550 CW 3.3 3.8 GE-5421 9W 230 0.3 1550 CCW 3.3 3.8 GE-5422 16W 115 1 1550 CW 3.5 4 GE-5811 16W 115 1 1550 CCW 3.5 4 GE-5812 16W 230 0.5 1550 CW 3.5 4 GE-5821 16W 230 0.5 1550 CCW 3.5 4 GE-5822 FEATURES: PERMANENTLY LUBRICATED TO RUN FOR YEARS VERY QUIET OPERATION 24 CORD WITH MOLDED STRAIN RELIEF TOTALLY ENCLOSED SUITABLE FOR ALL ANGLE OPERATION THREADED SHAFT 1/4-20,.51/.41 INCHES LONG SHADED POLE OR PERMANENT SPLIT CAPACITOR (PSC) EASY INSTALLATION: ALL MOTORS HAVE STANDARD 3 TAPPED END MOUNTING BOSSES. ALL MOTORS HAVE SINGLE SIDE PAD MOUNTING WITH 4 TAPPED HOLES, EXCEPT THE 2 WATT ALUMINUM. ALUMINUM, SHADED POLE DIMENSIONS (in.) WATTS VOLTS AMPS RPM ROT B C P/N 2W 115 0.1 1550 CW 2.8 3.3 GE-5108 2W 115 0.3 1550 CW 2.8 3.3 GE-5109 2.5W 115 0.3 1000 CW 2.8 3.3 GE-5113 4W 115 0.3 1550 CW 2.8 3.3 GE-5213 4W 115 0.3 1550 CCW 2.8 3.3 GE-5214 4W 230 0.2 1550 CW 2.8 3.3 GE-5223 4W 230 0.2 1550 CCW 2.8 3.3 GE-5224 6W 115 0.4 1550 CW 3.3 3.8 GE-5313 6W 115 0.4 1550 CCW 3.3 3.8 GE-5314 9W 115 0.6 1550 CW 3.3 3.8 GE-5413 9W 115 0.6 1550 CCW 3.3 3.8 GE-5414 9W 230 0.3 1550 CW 3.3 3.8 GE-5423 9W 230 0.3 1550 CCW 3.3 3.8 GE-5424 16W 115 1 1550 CW 3.5 4 GE-5813 16W 115 1 1550 CCW 3.5 4 GE-5814 16W 230 0.5 1550 CW 3.5 4 GE-5823 16W 230 0.5 1550 CCW 3.5 4 GE-5824 TYPICAL APPLICATIONS: REFRIGERATION CONDENSING UNITS UNIT HEATERS WALK-IN COOLERS DEHUMIDIFIERS WATER COOLERS REFRIGERATORS VENDING MACHINES CAST IRON, PSC - DUAL ROTATION DIMENSIONS (in.) WATTS VOLTS AMPS RPM B C P/N 4W 115 0.2 1550 3.5 4 GE-5114 6W 115 0.2 1550 3.5 4 GE-5116 9W 115 0.3 1550 3.5 4 GE-5117 16W 115 0.6 1550 3.5 4 GE-5118 878
ACCESS FITTINGS A-1 ACCESS FITTINGS Access Fittings provide a servicing aperture to facilitate recovery or recharge of refrigerants. All our Access Fittings come standard with 1/4 SAE male flare connections, built-in valve cores & brass caps. For availability of larger bulk pack quantities, please contact the factory. Features: AV Series have a permanent access ports & have 1/4 SAE male flare connections. AVX Series have a unique design, tube stops located on the tube to control insertion depth (thus preventing restriction of flow). P4227 879
ACCESS FITTINGS A-1 ACCESS FITTINGS PRODUCT NO. MODEL SIZE WEIGHT PACKAGE ORDER 100 QTY. NO. PACK AV2-456 Step down Solder 1/8 I.D. hole, 3/16, 1/4, 5/16 steps 0.045 5 6169 6294 AV2-456R Step down Solder 1/8 I.D. hole, 3/16, 1/4, 5/16 steps 0.043 5 6168 AV3-346 Step down Solder 3/16 O.D. tube or 1/4 and 3/8 solder 0.045 5 6141 6290 AV3-346R Step down Solder 3/16 O.D. tube or 1/4 and 3/8 solder 0.042 5 6230 AV-34 Straight Solder 3/16 O.D. tube or 1/4 solder 0.040 5 6142 6296 AV-34R Straight Solder 3/16 O.D. tube or 1/4 solder w/core remover 0.039 5 6232 AV-46R Straight Solder 1/4 O.D. tube or 3/8 solder w/core remover 0.043 5 6234 AVU-24R Half Union 1/8 M.P.T. or 1/4 O.D. solder 0.044 5 6236 AVU-45 Half Union 1/4 M.P.T. or 5/16 O.D. solder 0.072 5 6145 6287 AVU-45R Half Union 1/4 M.P.T. or 5/16 O.D. solder 0.070 5 6238 AVU-4 Union w/flare Nut 1/4 male flare x 1/4 access 0.089 4 6214 6286 AVU-4R Union w/flare Nut 1/4 male flare x 1/4 access w/core remover 0.089 4 6240 AVU-44 Union 1/4 male flare x 1/4 female flare 0.084 4 6215 6295 AVU-44R Union 1/4 male flare x 1/4 female flare w/core remover 0.089 4 6240 AVX-2R 1/8 O.D. x 2 copper tube extension 0.045 5 6248 6302 AVX-3R 3/16 O.D. x 2 copper tube extension 0.048 5 6250 6303 Straight Solder AVX-5 5/16 O.D. x 2 copper tube extension 0.069 5 6178 6293 with 2 extended AVX-5R 5/16 O.D. x 2 copper tube extension 0.069 5 6254 end tube and AVX-6 3/8 O.D. x 2 copper tube extension 0.080 5 6216 6299 stops AVX-6R 3/8 O.D. x 2 copper tube extension 0.080 5 6256 AVT-4 Copper Solder Tee 1/4 O.D. x tube x 1/4 male flare 0.065 3 6222 6283 AVT-4R access on branch 0.065 3 6546 AVT-5 Copper Solder Tee 5/16 O.D. x tube x 1/4 male flare 0.065 3 6223 AVT-5R access on branch 0.065 3 6547 AVT-6 Copper Solder Tee 3/8 O.D. x tube x 1/4 male flare 0.073 3 6224 6191 AVT-6R access on branch 0.073 3 6548 AVW-8 Copper Solder Tee 1/2 O.D. x tube x 1/4 male flare 0.088 2 6241 AVW-8R access on branch 0.088 1 6551 AVW-10 Copper Solder Tee 5/8 O.D. x tube x 1/4 male flare 0.094 2 6244 AVW-10R access on branch 0.094 1 6552 AVW-12 Copper Solder Tee 3/4 O.D. x tube x 1/4 male flare 0.101 2 6245 AVW-12R access on branch 0.101 1 6553 AVW-14 Copper Solder Tee 7/8 O.D. x tube x 1/4 male flare 0.131 1 6246 AVW-14R access on branch 0.131 1 6554 AVT-34 Brass Union Tee 1/8 M.P.T. x 1/4 male flare on run 0.098 3 6225 x 1/4 male flare access on branch AVT-44 Brass Union Tee 3-1/4 SAE Flare T Valve with 2 valve cores 0.098 3 6227 AVS-4 Union w/swivel Nut 1/4 male flare access x swivel nut 0.088 3 6247 Core Depressor on run AVS-44N* Swivel Nut and male flare access on branch 6195 AVS-64 Core Depressor 1/4 male flare x 1/4 access on run 0.138 3 6219 6272 AVS-64N* x swivel nut on branch 6196 AVB-46 Brass Straight 1/4 Lg. male flare x 1/4 solder Solder head body w/cap, core and nut 0.062 3 6124 R suffix identifies parts with core remover cap. *Identifies parts without core depressor. 880
A-1 ACCESS FITTINGS AVUX Series ACCESS FITTINGS Our new AVUX Series access fittings provide copper tubing with 1/8 pipe thread below the hex. Other various tube sizes are available to provide proper fitting. A core remover cap is included in the AVUX series. PRODUCT NO. AVB-46 AVU-345R AVUX-234R AVUX-2R AVUX-3R AVUX-4R SIZE 1/4 long male flare x c solder bulk head body w/cap & cap retainer 1/8 MPT 3/16, 1/4 5/16 steps 1/8 hole core tool 1/8 MPT 1/4 x 2 copper tube w/3/16 x 1/8 bushings 1/8 MPT 3/16, 1/4 5/16 steps 1/8 x 2 cooper ext. 1/8 MPT 3/16, 1/4 5/16 steps 3/16 x 2 cooper ext. 1/8 MPT 5/16 steps 1/4 x 2 cooper ext. core tools PACKAGE QTY. 3 5 5 5 5 5 P4228 P4229 A-1 VCT-1 VALVE CORE TOOL (Not Shown) Features a hollow handle for the storage of replacement valve cores. The brass body is knurled for easier grip. Supplied with a plated steel core remover cap for additional strength. VCRT VALVE CORE REMOVER TOOL Permits easy installation of new core in access fitting without loss of gas or charge. Replaces C/D 3910, Robinair #14650. VALVE CORES AND BRASS CAPS Replacement valve cores available 6 in a tube. Included in the container is the QC-4R core remover cap. Standard QC-4R caps sold separately. VALVE CORES TOOLS BRASS CAPS PRODUCT NO. DESCRIPTION WEIGHT QC-4R Cap w/core remover for 1/4 male flare 0.013 VCT-1 Valve Core Tool P4230 881
TOTALINE REFRIGERATION CONDENSERS P703 AIR-COOLED CONDENSERS AND DRY COOLERS Totaline s refrigeration condensers are used for refrigeration systems. These condensers are designed for large coolers or freezers. The Totaline fluid cooler is suitable as a secondary heat exchanger. Condensers are available in capacities from 41,000 BTUH to over 3 million BTUH. Dry type fluid coolers from 5 GPM to over 400 GPM. Condenser Features All Totaline refrigeration condensers provide the design flexibility required in replacement, renovation, and new construction. All refrigeration unit condensers feature the following benefits: Fan motors feature permanently lubricated, sealed ball bearings and inherent thermal protection for long life and dependable service Fan guards and motor mounts are welded wire construction for full protection from moving parts. Baked on powder epoxy coating protects from corrosion Aluminum fan blades are statically and dynamically balanced for smooth, vibration-free operation PVC coated wire fan guards with aluminum fans Labeled terminal block for field wiring Modular design allows minimal part inventory and replacement Plated hardware for light weight and corrosion-free assembly Weather resistant control box protects motor wiring Smooth tubes simplify change from CFC and HCFC to HFC refrigerant Exclusive non-metallic supports for friction free coil assembly Dry fluid coolers FXBs Available in single or multi circuits All units are ETL and CSA approved P4377 Dry Fluid Cooler & Heat Reclaim Unit Features Designed with features identical to our air-cooled condensers Options Copper to be copper fin coils available option Various fins spacing 6, 8, 10, 12 fins per inch Wide range of head pressure control from fan cycling methods as well as various flooding control methods to meet your application needs Wide range of control box options Available Types of Protective Coatings Pre-coated epoxy aluminum (Gold color) Blygold (PoluAl) (Aluminum color) Heresite (Baked Phenolic) (Brown Color) General Notes Packing Standard domestic packaging which provides coil protection Optional, full crate Ordering Information NOTE: You must order a control box and condenser/fluid cooler using two separate P/Ns. The two P/Ns must be submitted together as one order. 882
TOTALINE REFRIGERATION CONDENSERS P703 AIR-COOLED CONDENSERS AND DRY COOLERS AIR-COOLED CONDENSER, HEAT RECLAIM & DRY-TYPE FLUID COOLER NOMENCLATURE P703 C L D 180 H 9 Totaline Condenser C Condenser H Heat Reclaim F Dry Type Fluid Cooler Unit Voltage (V/Ph/Hz) 2 240/1/60 5 208-240/3/60 8 600/3/60 9 480/3/60 Horsepower (RPM) C 1/4 (825) M 1/2 (1140) L 1 (825) I 1-1/2 (1140) H 1-1/2 (850) Q 1/2 (560) Airflow H Horizontal Airflow D Direct Drive 8 8 Fins Per Inch (FPI) Nominal Condenser THR (Tons) @ 25 F TD (R-22) LEGEND TD Temperature Difference 883
TOTALINE REFRIGERATION CONDENSERS P703 AIR-COOLED CONDENSERS AND DRY COOLERS AIR-COOLED CONDENSER & FLUID COOLER CONTROL PANEL NOMENCLATURE TOTALINE TYPE OF FAN UNIT CONTROL OPTIONS PANEL PANEL ARRANGEMENT VOLTAGE VOLTAGE P 04 24 8 1 ACE 11 = 1 x 1 2 240/1/60 1 120/1/60 12 = 1 x 2 5 208-240/3/60 2 240/1/60 13 = 1 x 3 8 600/3/60 X 24/1/60 14 = 1 x 4 9 480/3/60 N NONE 15 = 1 x 5 22 = 2 x 2 23 = 2 x 3 N NONE 24 = 2 x 4 A MOTOR FUSING (IN PAIR FOR TWO FAN WIDE UNIT) 25 = 2 x 5 B INDIVIDUAL MOTOR FUSING (FOR TWO FAN WIDE UNIT ONLY) 26 = 2 x 6 C SPEED MOTOR CONTROLLER (PRESSURE SENSING) D SPEED MOTOR CONTROLLER (TEMPERATURE SENSING) E NON-FUSED DISCONNECT F FUSED DISCONNECT STANDARD PANELS 01 CONTROL BOX, TERMINAL BLOCK, NO CONTROLS, NO CONTACTORS 02 CONTACTOR(S) WITHOUT CONTROLS 03 CONTACTOR(S), AMBIENT FAN CYCLING 04 CONTACTOR(S), PRESSURE FAN CYCLING (2) 05 CONTACTOR(S), PRESSURE FAN CYCLING, DUAL CIRCUITS (3) 06 CONTACTOR(S), ELECTRONIC AQUASTAT THERMOSTAT CONTROL (1, 2) 07 CONTACTOR(S), ELECTRONIC AQUASTAT THERMOSTAT CONTROL, FIRST STAGE CYCLING (1, 2) 10 CONTACTOR(S), MECHANICAL AQUASTAT THERMOSTAT CONTROL (1, 2) 11 CONTACTOR(S), MECHANICAL AQUASTAT THERMOSTAT CONTROL, FIRST STAGE CYCLING (1, 2) 12 CONTACTOR(S), MOTORS INDIVIDUALLY WIRED, NO CONTROLS (4, 5) 13 SPLIT ELECTRICAL, CONTACTOR(S), ELECTRONIC AQUASTAT THERMOSTAT CONTROL (1, 4, 5, 6) 14 SPLIT ELECTRICAL, CONTACTOR(S), ELECTRONIC AQUASTAT THERMOSTAT CONTROL, FIRST STAGE CYCLING (1, 4, 5, 6) 16 SPLIT ELECTRICAL, CONTACTOR(S), MECHANICAL AQUASTAT THERMOSTAT CONTROL (1, 4, 5, 6) 17 SPLIT ELECTRICAL, CONTACTOR(S), MECHANICAL AQUASTAT THERMOSTAT CONTROL, FIRST STAGE CYCLING (1, 4, 5, 6) 18 SPLIT ELECTRICAL, CONTACTOR(S), AMBIENT FAN CYCLING (4, 5, 6) 19 SPLIT ELECTRICAL, CONTACTOR(S), PRESSURE FAN CYCLING (3, 4, 5, 6) 20 CONTACTOR(S), AMBIENT FAN CYCLING WITH PRESSURE OVERRIDE (2) 55 SPECIAL CONTROL PANEL SPECIFICATIONS: 1 AVAILABLE ONLY ON FLUID COOLED UNITS 2 AVAILABLE ONLY ON SINGLE CIRCUIT OR TWO CIRCUITS FOR SINGLE CIRCUIT APPLICATION 3 AVAILABLE ONLY ON TWO REFRIGERANT CIRCUITS UNITS 4 AVAILABLE ONLY ON TWO FANS WIDE UNITS 5 FAN MOTORS ARE INDIVIDUALLY WIRED, NOT IN PAIR (OPTION A NOT AVAILABLE) 6 DUAL POWER SUPPLY FOR TWO FANS WIDE UNITS (SUPPLIED WITH TWO ELECTRICAL BOXES) NOTES: 1 FIRST STAGE IS NOT CYCLED, UNLESS OTHERWISE NOTED 2 ON TWO FAN WIDE UNITS, FAN MOTORS ARE WIRED IN PAIRS, UNLESS OTHERWISE NOTED 884
TOTALINE REFRIGERATION CONDENSERS P703 AIR-COOLED CONDENSERS AND DRY COOLERS LOW CFM AIR-COOLED CONDENSERS (Standard Fin Spacing) TOTAL HEAT REJECTION MBTUH REFRIGERANT PART (R-22, R-134a) NUMBER CONNECTION SIZES CAP./CKT FAN CHARGE SHIPPING NUMBER TEMPERATURE DIFFERENCE (TD) CIRCUITS (in.) Btuh/F TD ARRANGEMENT (lbs) WEIGHT (CKT) (lbs) 1 F 15 F 20 F 25 F 30 F Discharge Liquid Summer Winter P703-CCD02 1.38 20.64 27.52 34.40 41.28 4 344 1 X 1 7/8 5/8 1.8 5.8 190 P703-CCD03 1.69 25.39 33.86 42.32 50.79 5 339 1 X 1 7/8 5/8 2.7 8.7 201 P703-CCD04 1.89 28.36 37.82 47.27 56.73 4 473 1 X 1 7/8 7/8 3.5 12 210 P703-CMD05 2.63 39.50 52.67 65.84 79.00 7 376 1 X 1 7/8 7/8 3.3 11 308 P703-CMD07 3.33 49.90 66.53 83.16 99.79 7 475 1 X 1 7/8 7/8 4.9 16 335 P703-CMD08 3.73 55.98 74.65 93.31 111.97 7 533 1 X 1 1-1/8 7/8 6.5 22 350 P703-CMD09 5.27 79.00 105.34 131.67 158.00 13 405 1 X 2 1-1/8 7/8 6.3 21 489 P703-CMD11 5.99 89.84 119.79 149.74 179.69 14 428 1 X 2 1-1/8 1-1/8 9.5 31 518 P703-CMD12 6.65 99.79 133.06 166.32 199.58 14 475 1 X 2 1-1/8 1-1/8 9.5 31 532 P703-CMD13 6.87 103.06 137.41 171.77 206.12 14 491 1 X 2 1-1/8 1-1/8 13 42 544 P703-CMD14 7.46 111.97 149.29 186.62 223.94 14 533 1 X 2 1-3/8 1-1/8 13 42 566 P703-CMD18 8.98 134.69 179.59 224.48 269.38 20 449 1 X 3 1-3/8 1-1/8 14 47 727 P703-CMD20 9.98 149.69 199.58 249.48 299.38 20 499 1 X 3 1-3/8 1-1/8 14 47 741 P703-CMD21 10.31 154.59 206.12 257.65 309.18 27 382 1 X 3 1-3/8 1-1/8 19 62 767 P703-CMD23 11.20 167.95 223.94 279.92 335.91 27 415 1 X 3 1-3/8 1-1/8 19 62 789 P703-CLD009 4.40 65.93 87.91 109.89 131.87 11 400 1 X 1 1-1/8 1-1/8 5.8 19 515 P703-CLD010 5.17 77.52 103.36 129.20 155.03 11 470 1 X 1 1-1/8 1-1/8 5.8 19 525 P703-CLD012 5.77 86.58 115.43 144.29 173.15 17 340 1 X 1 1-1/8 1-1/8 8.8 29 592 P703-CLD013 6.56 98.46 131.27 164.09 196.91 17 386 1 X 1 1-1/8 1-1/8 8.8 29 602 P703-CLD014 6.87 103.06 137.41 171.77 206.12 17 404 1 X 1 1-3/8 1-1/8 12 38 641 P703-CLD015 7.39 110.78 147.71 184.64 221.56 17 434 1 X 1 1-3/8 1-1/8 12 38 654 P703-CLD018 8.78 131.72 175.63 219.53 263.44 17 517 1 X 2 1-3/8 1-1/8 12 38 985 P703-CLD021 10.34 155.03 206.71 258.39 310.07 17 608 1 X 2 1-3/8 1-3/8 12 38 1005 P703-CLD023 11.55 173.30 231.07 288.83 346.60 26 444 1 X 2 1-5/8 1-3/8 17 57 1063 P703-CLD026 13.13 196.91 262.55 328.19 393.82 26 505 1 X 2 1-5/8 1-3/8 17 57 1091 P703-CLD028 13.73 205.97 274.63 343.28 411.94 35 392 1 X 2 1-5/8 1-3/8 23 76 1117 P703-CLD030 14.76 221.41 295.22 369.02 442.83 35 422 1 X 2 1-5/8 1-3/8 23 76 1159 P703-CLD035 17.33 259.88 346.50 433.13 519.75 52 333 1 X 3 1-5/8 1-5/8 26 85 1460 P703-CLD040 19.69 295.37 393.82 492.28 590.73 52 379 1 X 3 2-1/8 1-5/8 26 85 1490 P703-CLD042 20.68 310.22 413.62 517.03 620.43 34 608 2 X 2 (2) 1-3/8 (2) 1-3/8 23 75 1625 P703-CLD043 21.02 315.27 420.35 525.44 630.53 70 300 1 X 3 2-1/8 1-5/8 34 112 1570 P703-CLD045 22.13 331.90 442.53 553.16 663.80 70 316 1 X 3 2-1/8 1-5/8 34 112 1609 P703-CLD049 24.41 366.20 488.27 610.34 732.40 52 469 2 X 2 (2) 1-5/8 (2) 1-3/8 35 115 1792 P703-CLD050 24.41 366.20 488.27 610.34 732.40 52 469 1 X 4 2-1/8 1-5/8 34 112 1875 P703-CLD053 26.25 393.82 525.10 656.37 787.64 52 505 2 X 2 (2) 1-5/8 (2) 1-3/8 35 115 1781 P703-CLD054 26.25 393.82 525.10 656.37 787.64 52 505 1 X 4 2-1/8 1-5/8 34 112 1915 P703-CLD056 28.04 420.55 560.74 700.92 841.10 70 401 2 X 2 (2) 1-5/8 (2) 1-3/8 47 153 1882 P703-CLD057 28.04 420.55 560.74 700.92 841.10 70 401 1 X 4 2-1/8 1-5/8 46 150 2019 P703-CLD060 29.51 442.68 590.24 737.80 885.36 70 422 2 X 2 (2) 1-5/8 (2) 1-3/8 47 153 1934 P703-CLD061 29.51 442.68 590.24 737.80 885.36 70 422 1 X 4 2-1/8 1-5/8 46 150 2071 P703-CLD063 30.67 460.05 613.40 766.76 920.11 70 438 2 X 3 (2) 1-5/8 (2) 1-3/8 34 112 2323 P703-CLD066 32.82 492.28 656.37 820.46 984.56 52 631 1 X 5 2-1/8 2-1/8 43 140 2403 P703-CLD070 35.04 525.54 700.72 875.90 1051.08 70 501 1 X 5 2-1/8 2-1/8 57 187 2475 P703-CLD075 36.88 553.16 737.55 921.94 1106.33 70 527 1 X 5 2-1/8 2-1/8 57 187 2540 P703-CLD080 39.38 590.73 787.64 984.56 1181.47 104 379 2 X 3 (2) 2-1/8 (2) 1-5/8 52 169 2508 P703-CLD085 42.06 630.83 841.10 1051.38 1261.66 140 300 2 X 3 (2) 2-1/8 (2) 1-5/8 69 225 2664 P703-CLD090 44.26 663.94 885.26 1106.57 1327.89 140 316 2 X 3 (2) 2-1/8 (2) 1-5/8 69 225 2742 P703-CLD099 48.84 732.55 976.73 1220.92 1465.10 104 470 2 X 4 (2) 2-1/8 (2) 1-5/8 68 224 3029 P703-CLD106 52.51 787.64 1050.19 1312.74 1575.29 104 505 2 X 4 (2) 2-1/8 (2) 1-5/8 68 224 3129 P703-CLD113 56.06 840.96 1121.27 1401.59 1681.91 140 400 2 X 4 (2) 2-1/8 (2) 1-5/8 91 299 3338 P703-CLD120 59.01 885.21 1180.28 1475.35 1770.42 140 422 2 X 4 (2) 2-1/8 (2) 1-5/8 91 229 3442 P703-CLD124 61.16 917.43 1223.24 1529.06 1834.87 104 588 2 X 5 (2) 2-1/8 (2) 2-1/8 85 280 4198 P703-CLD132 65.65 984.70 1312.94 1641.17 1969.41 104 631 2 X 5 (2) 2-1/8 (2) 2-1/8 85 280 4298 P703-CLD142 70.08 1051.23 1401.64 1752.05 2102.46 140 501 2 X 5 (2) 2-1/8 (2) 2-1/8 114 373 4560 P703-CLD150 73.77 1106.62 1475.50 1844.37 2213.24 140 527 2 X 5 (2) 2-1/8 (2) 2-1/8 114 373 4690 P703-CLD159 78.76 1181.47 1575.29 1969.11 2362.93 86 916 2 X 6 (2) 2-5/8 (2) 2-1/8 164 553 5292 P703-CLD170 84.00 1260.02 1680.03 2100.04 2520.05 116 724 2 X 6 (2) 2-5/8 (2) 2-1/8 218 717 5642 P703-CLD180 88.54 1328.04 1770.71 2213.39 2656.07 116 763 2 X 6 (2) 2-5/8 (2) 2-1/8 218 717 5798 LEGEND TD Temperature Difference NOTES: 1. Multiply capacity by 0.98 for R-404A and R-507. 2. Multiply capacity by 0.92 for 50 Hz units. 3. Connections are based on 30 F TD, 40 F suction and R-22. 4. Refrigerant summer charge is based on 100 F liquid, 30% liquid and 70% vapor. 5. Refrigerant winter charge is based on 20 F liquid, 90% liquid and 10% vapor. 885
TOTALINE REFRIGERATION CONDENSERS P703 AIR-COOLED CONDENSERS AND DRY COOLERS LOW CFM AIR-COOLED CONDENSERS (8 FPI) TOTAL HEAT REJECTION MBTUH REFRIGERANT PART (R-22, R-134a) NUMBER CONNECTION SIZES CAP./CKT FAN CHARGE SHIPPING NUMBER TEMPERATURE DIFFERENCE (TD) CIRCUITS (in.) Btuh/F TD ARRANGEMENT (lbs) WEIGHT (CKT) (lbs) 1 F 15 F 20 F 25 F 30 F Discharge Liquid Summer Winter P703-CL8009 4.49 67.42 89.89 112.37 134.84 11 409 1 X 1 1-1/8 1-1/8 5.8 19 515 P703-CL8012 5.83 87.47 116.62 145.78 174.93 17 343 1 X 1 1-1/8 1-1/8 8.8 29 592 P703-CL8014 6.70 100.53 134.05 167.56 201.07 17 394 1 X 1 1-3/8 1-1/8 12 38 641 P703-CL8018 8.99 134.84 179.78 224.73 269.68 17 529 1 X 2 1-3/8 1-1/8 12 38 985 P703-CL8024 11.66 174.93 233.24 291.56 349.87 26 449 1 X 2 1-5/8 1-3/8 17 57 1063 P703-CL8027 13.40 201.07 268.09 335.12 402.14 35 383 1 X 2 1-5/8 1-3/8 23 76 1117 P703-CL8035 17.49 262.40 349.87 437.33 524.80 52 336 1 X 3 1-5/8 1-5/8 26 85 1460 P703-CL8036 17.98 269.68 359.57 449.46 539.35 34 529 2 X 2 (2) 1-3/8 (2) 1-3/8 23 75 1625 P703-CL8041 20.11 301.60 402.14 502.67 603.21 70 287 1 X 3 2-1/8 1-5/8 34 112 1570 P703-CL8047 23.32 349.87 466.49 583.11 699.73 52 449 2 X 2 (2) 1-5/8 (2) 1-3/8 35 115 1792 P703-CL8048 23.32 349.87 466.49 583.11 699.73 52 449 1 X 4 2-1/8 1-5/8 34 112 1875 P703-CL8053 26.81 402.14 536.18 670.23 804.28 70 383 2 X 2 (2) 1-5/8 (2) 1-3/8 47 153 1882 P703-CL8054 26.81 402.14 536.18 670.23 804.28 70 383 1 X 4 2-1/8 1-5/8 46 150 2019 P703-CL8055 26.97 404.51 539.35 674.19 809.03 70 385 2 X 3 (2) 1-5/8 (2) 1-3/8 34 112 2323 P703-CL8059 29.55 443.27 591.03 738.79 886.55 52 568 1 X 5 2-1/8 2-1/8 43 140 2403 P703-CL8068 33.51 502.67 670.23 837.79 1005.35 70 479 1 X 5 2-1/8 2-1/8 57 187 2475 P703-CL8071 34.99 524.80 699.73 874.67 1049.60 104 336 2 X 3 (2) 2-1/8 (2) 1-5/8 52 169 2508 P703-CL8081 40.21 603.21 804.28 1005.35 1206.41 140 287 2 X 3 (2) 2-1/8 (2) 1-5/8 69 225 2664 P703-CL8094 46.65 699.73 932.98 1166.22 1399.46 104 449 2 X 4 (2) 2-1/8 (2) 1-5/8 68 224 3029 P703-CL8108 53.62 804.28 1072.37 1340.46 1608.55 140 383 2 X 4 (2) 2-1/8 (2) 1-5/8 91 299 3338 P703-CL8118 58.37 875.56 1167.41 1459.26 1751.11 104 561 2 X 5 (2) 2-1/8 (2) 2-1/8 85 280 4198 P703-CL8135 67.04 1005.64 1340.86 1676.07 2011.28 140 479 2 X 5 (2) 2-1/8 (2) 2-1/8 114 373 4560 P703-CL8141 69.97 1049.60 1399.46 1749.33 2099.20 86 814 2 X 6 (2) 2-5/8 (2) 2-1/8 164 553 5292 P703-CL8162 80.43 1206.41 1608.55 2010.69 2412.83 116 693 2 X 6 (2) 2-5/8 (2) 2-1/8 218 717 5642 LEGEND FPI Fins per inch NOTES: 1. Multiply capacity of 0.98 for R-404A and R-507. 2. Multiply capacity by 0.92 for 50 Hz units. 3. Connections are based on 30 F TD, 40 F suction and R-22. 4. Refrigerant summer charge is based on 100 F liquid, 30% liquid and 70% vapor. 5. Refrigerant winter charge is based on 20 F liquid, 90% liquid and 10% vapor. HEAT RECLAIM UNITS TOTAL HEAT REJECTION MBTUH PART (R-22, R-134a) NUMBER CONNECTION SIZES REFRIGERANT SHIPPING CAP./CKT FAN NUMBER TEMPERATURE DIFFERENCE (TD) CIRCUITS (in.) CHARGE WEIGHT Btuh/F TD ARRANGEMENT (CKT) (lbs) (lbs) 1 F 30 F 35 F 40 F 45 F Discharge Liquid P703-HCD02 1.38 41.28 48.16 55.04 61.92 19 72 1 X 1 1-1/8 1-1/8 0.6 190 P703-HCD03 1.69 50.79 59.25 67.72 76.18 14 121 1 X 1 1-1/8 1-1/8 0.9 201 P703-HCD04 1.89 56.73 66.18 75.64 85.09 19 100 1 X 1 1-1/8 1-1/8 1.2 210 P703-HMD05 2.63 79.00 92.17 105.34 118.50 27 98 1 X 1 1-3/8 1-3/8 1.1 308 P703-HMD07 3.33 99.79 116.42 133.06 149.69 20 166 1 X 1 1-3/8 1-3/8 1.6 335 P703-HMD08 3.73 111.97 130.63 149.29 167.95 27 138 1 X 1 1-3/8 1-3/8 2.1 350 P703-HMD09 5.27 158.00 184.34 210.67 237.01 27 195 1 X 2 1-5/8 1-5/8 2.1 489 P703-HMD11 5.99 179.69 209.63 239.58 269.53 40 150 1 X 2 1-5/8 1-5/8 3.1 518 P703-HMD12 6.65 199.58 232.85 266.11 299.38 40 166 1 X 2 2-1/8 2-1/8 3.1 532 P703-HMD13 6.87 206.12 240.47 274.82 309.18 27 254 1 X 2 2-1/8 2-1/8 4.3 544 P703-HMD14 7.46 223.94 261.26 298.58 335.91 27 276 1 X 2 2-1/8 2-1/8 4.3 566 P703-HMD18 8.98 269.38 314.28 359.17 404.07 40 224 1 X 3 2-1/8 2-1/8 4.6 727 P703-HMD20 9.98 299.38 349.27 399.17 449.06 40 249 1 X 3 2-1/8 2-1/8 4.6 741 P703-HMD21 10.31 309.18 360.71 412.24 463.77 54 191 1 X 3 2-1/8 2-1/8 6.3 767 P703-HMD23 11.20 335.91 391.89 447.88 503.86 54 207 1 X 3 2-1/8 2-1/8 6.3 789 NOTES: 1. Multiply capacity of 0.98 for R-404A and R-507. 2. Multiply capacity by 0.92 for 50 Hz units. 3. Connections sizes are based on 40 F TD at 50% recovery. 4. Refrigerant charge is based on 10% liquid and 90% vapor. 886
TOTALINE REFRIGERATION CONDENSERS P703 AIR-COOLED CONDENSERS AND DRY COOLERS HIGH CFM AIR-COOLED CONDENSERS (Standard Fins) TOTAL HEAT REJECTION MBTUH REFRIGERANT PART (R-22, R-134a) NUMBER CONNECTION SIZES CAP./CKT FAN CHARGE SHIPPING NUMBER TEMPERATURE DIFFERENCE (TD) CIRCUITS (in.) Btuh/F TD ARRANGEMENT (lbs) WEIGHT (CKT) (lbs) 1 F 15 F 20 F 25 F 30 F Discharge Liquid Summer Winter P703-CID010 5.08 76.18 101.57 126.97 152.36 11 462 1 X 1 1-1/8 1-1/8 5.8 19 515 P703-CID011 5.88 88.21 117.61 147.02 176.42 11 535 1 X 1 1-1/8 1-1/8 5.8 19 525 P703-CID013 6.59 98.90 131.87 164.84 197.80 17 388 1 X 1 1-1/8 1-1/8 8.8 29 592 P703-CID014 7.39 110.78 147.71 184.64 221.56 17 434 1 X 1 1-1/8 1-1/8 8.8 29 602 P703-CID016 7.76 116.42 155.23 194.04 232.85 17 457 1 X 1 1-3/8 1-1/8 12 38 641 P703-CID017 8.27 124.00 165.33 206.66 248.00 17 486 1 X 1 1-3/8 1-1/8 12 38 654 P703-CID020 10.17 152.51 203.35 254.18 305.02 17 598 1 x 2 1-3/8 1-1/8 12 38 985 P703-CID023 11.76 176.42 235.22 294.03 352.84 17 692 1 X 2 1-3/8 1-3/8 12 38 1005 P703-CID025 13.20 197.95 263.93 329.92 395.90 26 508 1 X 2 1-5/8 1-3/8 17 57 1063 P703-CID029 14.78 221.71 295.61 369.52 443.42 26 568 1 X 2 1-5/8 1-3/8 17 57 1091 P703-CID031 15.52 232.85 310.46 388.08 465.70 35 444 1 X 2 1-5/8 1-3/8 23 76 1117 P703-CID034 16.54 248.14 330.86 413.57 496.29 35 473 1 X 2 1-5/8 1-3/8 23 76 1159 P703-CID039 19.79 296.85 395.80 494.75 593.70 52 381 1 X 3 1-5/8 1-5/8 26 85 1460 P703-CID044 22.17 332.49 443.32 554.15 664.98 52 426 1 X 3 2-1/8 1-5/8 26 85 1490 P703-CID046 22.98 344.67 459.56 574.45 689.34 34 676 2 X 2 (2) 1-3/8 (2) 1-3/8 23 75 1625 P703-CID049 23.29 349.42 465.89 582.37 698.84 70 333 1 X 3 2-1/8 1-5/8 34 112 1570 P703-CID051 24.80 371.99 495.99 619.99 743.99 70 354 1 X 3 2-1/8 1-5/8 34 112 1609 P703-CID054 27.48 412.24 549.65 687.06 824.47 52 529 2 X 2 (2) 1-5/8 (2) 1-3/8 35 115 1792 P703-CID055 27.48 412.24 549.65 687.06 824.47 52 529 1 X 4 2-1/8 1-5/8 34 112 1875 P703-CID058 29.54 443.12 590.83 738.54 886.25 52 568 2 X 2 (2) 1-5/8 (2) 1-3/8 35 115 1781 P703-CID059 29.54 443.12 590.83 738.54 886.25 52 568 1 X 4 2-1/8 1-5/8 34 112 1915 P703-CID064 31.06 465.84 621.13 776.41 931.69 70 444 2 X 2 (2) 1-5/8 (2) 1-3/8 47 153 1882 P703-CID065 31.06 465.84 621.13 776.41 931.69 70 444 1 X 4 2-1/8 1-5/8 46 150 2019 P703-CID068 33.08 496.14 661.52 826.90 992.28 70 473 2 X 2 (2) 1-5/8 (2) 1-3/8 47 153 1934 P703-CID069 33.08 496.14 661.52 826.90 992.28 70 473 1 X 4 2-1/8 1-5/8 46 150 2071 P703-CID070 35.28 529.25 705.67 882.09 1058.51 70 504 2 X 3 (2) 1-5/8 (2) 1-3/8 34 112 2323 P703-CID073 36.95 554.20 738.94 923.67 1108.40 52 711 1 X 5 2-1/8 2-1/8 43 140 2403 P703-CID079 38.82 582.27 776.36 970.45 1164.54 70 555 1 X 5 2-1/8 2-1/8 57 187 2475 P703-CID085 41.33 619.99 826.65 1033.31 1239.98 70 590 1 X 5 2-1/8 2-1/8 57 187 2540 P703-CID088 44.31 664.69 886.25 1107.81 1329.37 104 426 2 X 3 (2) 2-1/8 (2) 1-5/8 52 169 2508 P703-CID095 46.57 698.54 931.39 1164.24 1397.09 140 333 2 X 3 (2) 2-1/8 (2) 1-5/8 69 225 2664 P703-CID101 49.62 744.28 992.38 1240.47 1488.56 140 354 2 X 3 (2) 2-1/8 (2) 1-5/8 69 225 2742 P703-CID112 54.96 824.47 1099.30 1374.12 1648.94 104 529 2 X 4 (2) 2-1/8 (2) 1-5/8 68 224 3029 P703-CID119 59.08 886.25 1181.66 1477.08 1772.50 104 568 2 X 4 (2) 2-1/8 (2) 1-5/8 68 224 3129 P703-CID129 62.09 931.39 1241.86 1552.32 1862.78 140 444 2 X 4 (2) 2-1/8 (2) 1-5/8 91 299 3338 P703-CID137 66.14 992.13 1322.84 1653.55 1984.26 140 472 2 X 4 (2) 2-1/8 (2) 1-5/8 91 229 3442 P703-CID141 68.72 1030.74 1374.32 1717.90 2061.48 104 661 2 X 5 (2) 2-1/8 (2) 2-1/8 85 280 4198 P703-CID149 73.87 1108.11 1477.48 1846.85 2216.21 104 710 2 X 5 (2) 2-1/8 (2) 2-1/8 85 280 4298 P703-CID162 77.64 1164.54 1552.72 1940.90 2329.07 140 555 2 X 5 (2) 2-1/8 (2) 2-1/8 114 373 4560 P703-CID171 82.68 1240.27 1653.70 2067.12 2480.54 140 591 2 X 5 (2) 2-1/8 (2) 2-1/8 114 373 4690 P703-CID178 88.64 1329.67 1772.89 2216.12 2659.34 86 1031 2 X 6 (2) 2-5/8 (2) 2-1/8 164 553 5292 P703-CID194 93.14 1397.09 1862.78 2328.48 2794.18 116 803 2 X 6 (2) 2-5/8 (2) 2-1/8 218 717 5642 P703-CID205 99.89 1498.37 1997.82 2497.28 2996.73 116 861 2 X 6 (2) 2-5/8 (2) 2-1/8 218 717 5798 NOTES: 1. Multiply capacity of 0.98 for R-404A and R-507. 2. Multiply capacity by 0.92 for 50 Hz units. 3. Connections sizes are based on 30 F TD, 40 F suction and R-22. 4. Refrigerant summer charge is based on 100 F liquid, 30% liquid and 70% vapor. 5. Refrigerant winter charge is based on 20 F liquid, 90% liquid and 10% vapor. 887
TOTALINE REFRIGERATION UNIT COOLERS P704 REFRIGERATION UNIT COOLERS Thirteen different models of unit coolers featuring many capacities and types allow flexibility to meet most applications. Standard Features: All Totaline refrigeration coolers provide the design flexibility required in replacement, renovation, and new construction. Unit coolers are available in many models to suit most needs. Low sound levels Heavy duty construction Wide selection of fin spacing available Corrosion resistant fan guards (silver color) Easy access to refrigerant and electrical connections Warranty against material and labor defects UL listed NSF approved Options: Custom coil manufacturing i.e., gravity coils, copper tube/copper fin Custom fin spacing i.e., 3 Fin Per Inch TX valves and solenoid valves Option coil coating available for adverse environments Available Types of Protective Coating: Pre-coated epoxy aluminum (Gold color) Blygold (Polu Al) (Aluminum color) Heresite (Baked Pheonolic) (Brown color) General Note: 240 volt unit can be used for 200-220/1/50. P4378A P4378B P4378D P704 NOMENCLATURE P704 E L A 224 1 1 Totaline Unit Cooler E Evaporator Unit Voltage (V/Ph/Hz) 1 120/1/60 2 240/1/60 5 208-240/3/60 8 600/3/60 9 480/3/60 B Blast Freezer C Compact Reach-In D Dual Flow Reach-In F Free Standing Blast Freezer H High Profile Unit Cooler I Industrial Unit Cooler K Compact Unit Cooler L Low Height Unit Cooler M Medium Profile Unit Cooler P Medium Velocity Unit Cooler S Single Flow Unit Cooler V Low Velocity Unit Cooler W Wall Mount Reach-In A Air Defrost E Electric Defrost G Reverse Cycle Defrost With Electric Heated Drain Pan H Three Pipe Defrost With Electric Heated Drain Pan R Reverse Cycle Hot Gas Defrost T Three Pipe Hot Gas Defrost Product Generation Unit Capacity @ 10 F TD 22,400 Btuh LEGEND TD Temperature Difference 888
TOTALINE REFRIGERATION UNIT COOLERS P704 REFRIGERATION UNIT COOLERS P704-ECA SPACE SAVER REACH-IN-UNIT COOLERS (Air Defrost) FOR COOLERS ABOVE +34 F Single coil construction. Heavy gauge textured aluminum casings with polycarbonate fan guards, polypropylene fans and stainless steel or plated hardware for a light weight and corrosion free assembly. Life lubricated, thermal protected, heavy duty fan motors are provided for long life and dependable service. Air is discharged through the back of the unit. Ceiling or back wall mounting. Air Defrost MODEL CAPACITY (BTU/H) UNIT SIZE (in.) SHIPPING NUMBER 10 F TD 15 F TD Depth Height Width WEIGHT (Lbs) P704-ECA100-(1) 1000 1500 10-1/4 7-3/4 16-5/8 10.5 P704-ECA130-(1) 1300 1950 10-1/4 7-3/4 16-5/8 11.5 P704-ECA150-(1) 1500 2250 10-1/4 7-3/4 16-5/8 12.5 P4379 P704-EWA MULLION REACH-IN-UNIT COOLERS (Air Defrost) FOR COOLERS ABOVE +34 F Single coil construction. Heavy gauge textured aluminum casings with polycarbonate fan guards, polypropylene fans and stainless steel or plated hardware for a light weight and corrosion free assembly. Life lubricated, thermal protected, heavy duty fan motors are provided for long life and dependable service. Up or down airflow. Wall or mullion mounted. Upflow standard configuration can be modified to downflow. Air Defrost MODEL CAPACITY (BTU/H) UNIT SIZE (in.) SHIPPING NUMBER 10 F TD 15 F TD Depth Height Width WEIGHT (Lbs) P704-EWA130-(1) 1300 1950 5-3/4 18-1/4 15-3/4 13 P704-EWA180-(1) 1800 2700 5-3/4 18-1/4 15-3/4 14 P704-EWA230-(1) 2300 3450 5-3/4 18-1/4 21-3/4 17 Models ECA and EWA are available in: 1 = 120/1/60 2 = 240/1/60 NOTE: Standard voltage for ECA and EWA is 120/1/60, optional voltage is 240/1/60. P4380 P704-EDA DUAL FLOW REACH-IN-UNIT COOLERS (Air Defrost) FOR COOLERS ABOVE +34 F Dual coil construction for equal air distribution on both sides of the cooler. Heavy gauge textured aluminum casings with polycarbonate fan guards, polypropylene fans and stainless steel or plated hardware for a light weight and corrosion free assembly. Life lubricated, impedance protected, heavy duty fan motors are provided for long life and dependable service. Air Defrost MODEL CAPACITY (BTU/H) UNIT SIZE (in.) SHIPPING NUMBER 10 F TD 15 F TD Depth Height Width WEIGHT (Lbs) P704-EDA102-(1) 1000 1500 14-1/8 3-1/2 18-1/8 11.5 P704-EDA132-(1) 1300 1950 14-1/8 3-1/2 18-1/8 12.5 P704-EDA152-(1) 1500 2250 14-1/8 4-1/2 18-1/8 13 P704-EDA182-(1) 1800 2700 14-1/8 4-1/2 18-1/8 14 P704-EDA232-(1) 2300 3450 17-1/8 5-1/2 20-1/8 17 P704-EDA282-(1) 2800 4200 17-1/8 5-1/2 20-1/8 18.5 P704-EDA332-(1) 3300 4950 17-1/8 5-1/2 20-1/8 20 P4381 889
TOTALINE REFRIGERATION UNIT COOLERS P704 REFRIGERATION UNIT COOLERS P704-ESA SINGLE FLOW REACH-IN-UNIT COOLERS (Air Defrost) FOR COOLERS ABOVE +34 F Single coil construction for air distribution on the back of cooler. Heavy gauge textured aluminum casings with polycarbonate fan guards, polypropylene fans and stainless steel or plated hardware for a light weight and corrosion free assembly. Life lubricated, impedance protected, heavy duty fan motors are provided for long life and dependable service. Air Defrost MODEL CAPACITY (BTU/H) UNIT SIZE (in.) SHIPPING NUMBER 10 F TD 15 F TD Depth Height Width WEIGHT (Lbs) P704-ESA102-(1) 1000 1500 15 4-1/2 17-1/4 9.0 P704-ESA132-(1) 1300 1950 15 4-1/2 17-1/4 10.0 P704-ESA152-(1) 1500 2250 15 4-1/2 21-3/4 11.5 P704-ESA182-(1) 1800 2700 15 4-1/2 25-3/4 13.0 P704-ESA232-(1) 2300 3450 15 4-1/2 33-3/4 17.0 P704-ESA282-(1) 2800 4200 15 4-1/2 33-3/4 18.5 P704-ESA332-(1) 3300 4900 15 5-1/2 33-3/4 20.0 P704-ESA452-(1) 4500 6750 17 5-1/2 43-3/4 27.0 P704-ESE552-(1) 5500 8250 17 5-1/2 43-3/4 32.5 P4382 Models EDA and ESA are available in: 1 = 120/1/60 2 = 240/1/60 NOTE: Standard voltage for EDA and ESA is 120/1/60, optional is 240/1/60. P704-ESE SINGLE FLOW REACH-IN-UNIT COOLERS (Electric Defrost) FOR COOLERS AND FREEZERS FROM 20 TO +34 F Single coil construction for air distribution to back of cooler or freezer. These units are provided with stainless steel low watt density tubular heaters, defrost termination and fan delay thermostat for positive defrost and high efficiency. Heavy gauge textured aluminum casings with polycarbonate fan guards, polypropylene fans and stainless steel or plated hardware for a light weight and corrosion free assembly. Life lubricated, impedance protected, heavy duty fan motors are provided for long life and dependable service. Electric Defrost P4382 MODEL CAPACITY (BTU/H) UNIT SIZE (in.) SHIPPING NUMBER 20 F +20 F Depth Height Width WEIGHT (Lbs) P704-ESE102-(1) 850 1000 15 4-1/2 17-1/4 11.0 P704-ESE132-(1) 1105 1300 15 4-1/2 17-1/4 11.5 P704-ESE152-(1) 1275 1500 15 4-1/2 21-3/4 13.5 P704-ESE182-(1) (2) 1530 1800 15 4-1/2 25-3/4 15.5 P704-ESE232-(1) (2) 1955 2300 15 4-1/2 33-3/4 19.5 P704-ESE282-(1) (2) 2380 2800 15 4-1/2 33-3/4 21.0 P704-ESE332-(1) (2) 2805 3300 15 5-1/2 33-3/4 23.0 P704-ESE452-(1) (2) 3825 4500 17 5-1/2 43-3/4 30.5 P704-ESE552-(1) (2) 4675 5500 17 5-1/2 43-3/4 35.5 Model ESE is available in: 1 = 120/1/60 2 = 240/1/60 NOTE: Standard voltage for ESE is 240/1/60, optional voltage is 120/1/60. 890
TOTALINE REFRIGERATION UNIT COOLERS P704 REFRIGERATION UNIT COOLERS P704-ELA HIGH VELOCITY WALK-IN-UNIT COOLERS (Air Defrost) FOR COOLERS ABOVE +34 F High velocity/single coil construction for air distribution toward the center of the cooler. The fans draw air from the evaporator coil and discharge it through the fan guards on the front of the unit. Air throw is 20 to 30 ft. Life lubricated, thermal protected, heavy duty fan motors are provided for long life and dependable service. Heavy gauge textured aluminum casings with polycarbonate fan guards, aluminum fans and stainless steel or plated hardware for a light weight and corrosion free assembly. Air Defrost MODEL CAPACITY (BTU/H) UNIT SIZE (in.) SHIPPING NUMBER 10 F TD 15 F TD Depth Height Width WEIGHT (Lbs) P704-ELA0381-(1) 3,800 5,700 11-1/2 13-1/4 31-1/8 35 P704-ELA0491-(1) 4,900 7,350 11-1/2 13-1/4 31-1/8 39 P704-ELA0561-(1) 5,600 8,400 11-1/2 13-1/4 31-1/8 42 P704-ELA0661-(1) 6,600 9,900 11-1/2 13-1/4 43-1/8 52 P704-ELA0831-(1) 8,300 12,450 11-1/2 13-1/4 43-1/8 57 P704-ELA0961-(1) 9,600 14,400 11-1/2 13-1/4 43-1/8 63 P704-ELA1121-(1) 11,200 16,800 11-1/2 13-1/4 51-1/8 96 P704-ELA1471-(1) 14,700 22,050 11-1/2 13-1/4 71-1/8 107 P704-ELA1681-(1) 16,800 25,200 11-1/2 13-1/4 71-1/8 123 P704-ELA1851-(1) 18,500 27,750 11-1/2 13-1/4 71-1/8 138 P704-ELA2241-(1) 22,400 33,600 11-1/2 13-1/4 91-1/8 152 P704-ELA2801-(1) 28,000 42,000 11-1/2 13-1/4 111-1/8 180 P704-ELA3361-(1) 33,600 50,400 11-1/2 13-1/4 131-1/8 207 P704-ELA3701-(1) 37,000 55,500 11-1/2 13-1/4 131-1/8 220 Model ELA is available in: 1 = 120/1/60 2 = 240/1/60 5 = 208-240/3/60 NOTE: Standard voltage for ELA is 120/1/60, optional voltage is 240/1/60. ELA/ELE P4384 P704-ELE HIGH VELOCITY WALK-IN-UNIT COOLERS (Electric Defrost) FOR COOLERS AND FREEZERS FROM 20 TO +34 F High velocity/single coil construction for air distribution toward the center of the cooler. The fans draw air from the evaporator coil and discharge it through the fan guards on the front of the unit. Air throw is 20 to 30 ft. Life lubricated, thermal protected, heavy duty fan motors are provided for long life and dependable service. Electric Defrost MODEL CAPACITY (BTU/H) @ 10 F TD UNIT SIZE (in.) SHIPPING NUMBER 20 F +20 F Depth Height Width WEIGHT (Lbs) P704-ELE0441-(2) 3,740 4,400 11-1/2 13-1/4 31-1/4 45 P704-ELE0521-(2) 4,420 5,200 11-1/2 13-1/4 31-1/4 47 P704-ELE0781-(2) 6,630 7,800 11-1/2 13-1/4 43-1/4 64 P704-ELE0901-(2) 7,650 9,000 11-1/2 13-1/4 43-1/4 70 P704-ELE1041-(2) 8,840 10,400 11-1/2 13-1/4 51-1/4 105 P704-ELE1321-(2) 11,220 13,200 11-1/2 13-1/4 71-1/4 120 P704-ELE1561-(2) 13,260 15,600 11-1/2 13-1/4 71-1/4 135 P704-ELE1751-(2) 14,875 17,500 11-1/2 13-1/4 71-1/4 146 P704-ELE2081-(2) 17,680 20,800 11-1/2 13-1/4 91-1/4 168 P704-ELE2601-(2) 22,100 26,000 11-1/2 13-1/4 111-1/4 199 P704-ELE3121-(2) 26,520 31,200 11-1/2 13-1/4 131-1/4 230 P704-ELE3501-(2) 29,750 35,000 11-1/2 13-1/4 131-1/4 243 Model ELE is available in: NOTE: Standard voltage for ELE is 240/1/60, optional voltage is 120/1/60. 1 = 120/1/60 2 = 240/1/60 5 = 208-240/3/60 Heavy gauge textured aluminum casings with polycarbonate fan guards, aluminum fans and stainless steel or plated hardware for a light weight and corrosion free assembly. Series ELE units are provided with stainless steel, flexible low watt density tubular heaters inserted within the evaporator, terminal block, defrost termination and fan delay thermostat for positive defrost and high efficiency. 891
TOTALINE REFRIGERATION UNIT COOLERS P704 REFRIGERATION UNIT COOLERS P704-ELR/ELT HIGH VELOCITY WALK-IN-UNIT COOLERS (Gas Defrost) FOR COOLERS AND FREEZERS FROM 30 F TO +34 F High velocity/single coil construction for air distribution toward the center of the cooler. The fans draw air from the evaporator coil and discharge it through the fan guards on the front of the unit. Air throw is 20 to 30 ft. Life lubricated, thermal protected, heavy duty fan motors are provided for long life and dependable service. Heavy gauge textured aluminum casings with polycarbonate fan guards, aluminum fans and stainless steel or plated hardware for a light weight and corrosion free assembly. ELR and ELT series are provided with hot gas drain pan grid, adjustable fan delay thermostat and defrost termination thermostat. P4384 ELR Reverse style hot gas defrost ELT Three pipe hot gas defrost with gas drain pan Gas Defrost CAPACITY (BTU/H) MODEL UNIT SIZE (in.) SHIPPING @ 10 F TD NUMBER WEIGHT (Lbs) 20 F +20 F Depth Height Width P704-EL( )0441-(1) 3,740 4,400 11-1/2 13-1/4 31-1/4 42 P704-EL( )0521-(1) 4,420 5,200 11-1/2 13-1/4 31-1/4 45 P704-EL( )0781-(1) 6,630 7,800 11-1/2 13-1/4 43-1/4 60 P704-EL( )0901-(1) 7,650 9,000 11-1/2 13-1/4 43-1/4 66 P704-EL( )1041-(1) 8,840 10,400 11-1/2 13-1/4 51-1/4 99 P704-EL( )1321-(1) 11,220 13,200 11-1/2 13-1/4 71-1/4 113 P704-EL( )1561-(1) 13,260 15,600 11-1/2 13-1/4 71-1/4 128 P704-EL( )1751-(1) 14,875 17,500 11-1/2 13-1/4 71-1/4 148 P704-EL( )2081-(1) 17,680 20,800 11-1/2 13-1/4 91-1/4 159 P704-EL( )2601-(1) 22,100 26,000 11-1/2 13-1/4 111-1/4 187 P704-EL( )3121-(1) 26,520 31,200 11-1/2 13-1/4 131-1/4 215 P704-EL( )3501-(1) 29,750 35,000 11-1/2 13-1/4 131-1/4 238 Models ELR and ELT are available in: 1 = 120/1/60 2 = 240/1/60 5 = 208-240/3/60 NOTES: 1. Standard voltage for ELR and ELT is 120/1/60, optional voltage is 240/1/60. 2. Standard units are 6 FPI, for 4 FPI multiply capacity by 0.85. 892
TOTALINE REFRIGERATION UNIT COOLERS P704 REFRIGERATION UNIT COOLERS P704-EPA MEDIUM VELOCITY WALK-IN-UNIT COOLERS (Air Defrost) FOR COOLERS ABOVE +34 F Medium velocity/dual coil construction. Air distribution on either side of the cooler. Air throw is 8 to 15 ft each side. Heavy gauge textured aluminum casings with polycarbonate fan guards, ALUMINUM fans and stainless steel or plated hardware for a light weight and corrosion free assembly. Life lubricated, thermal protected, heavy duty fan motors are provided for long life and dependable service. Air Defrost MODEL CAPACITY (BTU/H) UNIT SIZE (in.) SHIPPING NUMBER 10 F TD 15 F TD Depth Height Width WEIGHT (Lbs) P704-EPA0561-(1) 5,600 8,400 24 9-1/2 31-3/8 51 P704-EPA0831-(1) 8,300 12,450 24 9-1/2 43-3/8 69 P704-EPA0961-(1) 9,600 14,400 24 9-1/2 43-3/8 75 P704-EPA1121-(1) 11,200 16,800 24 9-1/2 51-3/8 98 P704-EPA1471-(1) 14,700 22,050 24 9-3/4 71-3/8 110 P704-EPA1681-(1) 16,800 25,200 24 9-3/4 71-3/8 121 P704-EPA1851-(1) 18,500 27,750 24 9-3/4 71-3/8 143 P704-EPA2241-(1) 22,400 33,600 24 9-3/4 91-3/8 156 P704-EPA2801-(1) 28,000 42,000 24 10 111-3/8 193 P704-EPA3361-(1) 33,600 50,400 24 10 131-3/8 227 P704-EPA3701-(1) 37,000 55,500 24 10 131-3/8 248 Model EPA is available in: 1 = 120/1/60 2 = 240/1/60 NOTES: 1. Standard voltage for EPA is 120/1/60, optional voltage is 240/1/60. 2. Standard units are 8 FPI, for 4 FPI multiply capacity by 0.75. EPA/EPE P4386 P704-EPE MEDIUM VELOCITY WALK-IN-UNIT COOLERS (Electric Defrost) FOR COOLERS FROM +26 F TO +34 F Medium velocity/dual coil construction. Air distribution on either side of the cooler. Air throw is 8 to 15 ft each side. Heavy gauge textured aluminum casings with polycarbonate fan guards, ALUMINUM fans and stainless steel or plated hardware for a light weight and corrosion free assembly. Series EPE units are provided with stainless steel, flexible low watt density tubular heaters inserted within the evaporator, terminal block, defrost termination and fan delay thermostat for positive defrost and high efficiency. Electric Defrost MODEL CAPACITY (BTU/H) UNIT SIZE (in.) SHIPPING NUMBER 10 F TD 15 F TD Depth Height Width WEIGHT (Lbs) P704-EPE0521-(2) 5,200 7,800 24 9-1/2 31-3/8 56 P704-EPE0781-(2) 7,800 11,700 24 9-1/2 43-3/8 77 P704-EPE0901-(2) 9,000 13,500 24 9-1/2 43-3/8 83 P704-EPE1041-(2) 10,400 15,600 24 9-1/2 51-3/8 108 P704-EPE1321-(2) 13,200 19,800 24 9-3/4 71-3/8 124 P704-EPE1561-(2) 15,600 23,400 24 9-3/4 71-3/8 135 P704-EPE1751-(2) 17,500 26,250 24 9-3/4 71-3/8 160 P704-EPE2081-(2) 20,800 31,200 24 9-3/4 91-3/8 176 P704-EPE2601-(2) 26,000 39,000 24 10 111-3/8 216 P704-EPE3121-(2) 31,200 46,800 24 10 131-3/8 256 P704-EPE3501-(2) 35,000 52,500 24 10 131-3/8 267 Model EPE is available in: 1 = 120/1/60 2 = 240/1/60 NOTES: 1. Standard voltage for EPE is 240/1/60, optional voltage is 120/1/60. 2. Standard units are 6 FPI, for 4 FPI multiply capacity by 0.85. 893