COPYRIGHT 2007, POWERS #CAT-X023 REV. 1/07

COPYRIGHT 2007, POWERS #CAT-X023 REV. 1/07 All photographs and illustrations are considered to be a representation of the actual item. In some cases there may be slight variations. This catalog, copy, part numbers and unique method of illustrating products is copyrighted by Powers. All rights reserved. No portion of this catalog may be reproduced in any form or by any means in whole or in part, without the written consent of Powers. Powers reserves the right to make any and all changes and to discontinue any of its products without notice. Not responsible for typographical errors.

ALPHABETICAL INDEX DESCRIPTION................PAGE DESCRIPTION................PAGE DESCRIPTION................PAGE A ACCESSORIES, FAUCET...... C14, C15 ACCESSORIES, PRE-RINSE... C14, C15 ADAPTORS..................... C33 ADD-ON FAUCET................. C15 AERATORS...................... C33 B BASKET & DIPPERWELL ASSEMBLIES................... C46 C CHECK VALVE................... C25 D DECK MOUNT LAVATORY FAUCETS............. C27, C29, C30 DECK MOUNT SINK FAUCETS............. C18, C19, C28 M MIXING VALVE, MECHANICAL...... C33 MOUNTING KITS................. C14 O OVERFLOW DRAINS.............. C45 P PANTRY FAUCETS........... C20, C21 POT FILLERS.................... C12 PRE-RINSE HOSE REELS......... C24 PRE-RINSE, DECK MOUNT 4" & 8"... C7 PRE-RINSE, DECK MOUNT BASE... C11 PRE-RINSE, DOUBLE PANTRY...... C6 PRE-RINSE, SINGLE DECK MOUNT........................ C10 PRE-RINSE, SINGLE WALL MOUNT........................C10 PRE-RINSE, SWIVEL ARM....... C8, C9 PRE-RINSE, WALL MOUNT.......... C6 PRE-RINSE, WALL MOUNT BASE... C11 S SERVICE SINK FAUCETS.......... C32 SHUT OFF CONTROL VALVE....... C25 SINK ASSEMBLIES, PRE-RINSE................ C37, C38 SINK BOWLS, DEEP DRAWN....... C36 SINK BOWLS, FABRICATED........ C35 SOAP DISPENSERS.............. C31 SPOUT ASSEMBLIES......... C26, C34 SPRAY VALVE ASSEMBLIES....... C14 SPRAY VALVE KITS............... C14 SUPPLY INLET................... C14 SUPPLY INLETS OFFSET.......... C15 SWIVEL ARM SUPPORT........... C14 SWIVEL JOINT.................... C8 U UTILITY SPRAYS................. C12 V VACUUM BREAKERS......... C25, C33 E ELEVATED SPOUT FAUCETS....... C23 G GRAB BARS..................... C31 H HANDLE, 4" BLADE............... C15 HANDLE, 6" BLADE............... C15 HANDLE, CROSS STYLE.......... C15 HANDLE, DESIGNER STYLE....... C15 HOSE ASSEMBLIES.............. C14 HOSE ASSEMBLIES W/VB..........C14 Q QUICK-WASH FAUCET CONTROL... C33 R REMOTE MIXING VALVE........... C25 ROTARY DRAIN, ABS............. C39 ROTARY DRAIN, NICKEL PLATED... C41 ROTARY DRAIN, STAINLESS....... C40 W WALL BRACKET................. C14 WALL HOOK..................... C14 WALL MOUNT FAUCETS, SINGLE........................ C22 WALL MOUNT LAVATORY FAUCETS...................... C27 WALL MOUNT SINK FAUCETS............. C16, C17, C28 WASTE OUTLET, LEVER HANDLE... C42 WASTE OUTLET, TWIST HANDLE... C43 NUMERICAL INDEX ON PAGES C47 & C48 C1

Excellence in engineering... inside and out. QUALITY FAUCETS & PRE-RINSE ASSEMBLIES designed specifically for the foodservice industry. The POWERS faucet line has been the choice among industrial, institutional and food service customers since its introduction. POWERS has continually earned the highest marks while becoming the most durable, versatile line of plumbing products available anywhere. This outstanding record of accomplishment reflects generations of trade experience and know how that are integral components of the design and manufacture of this unique plumbing line. POWERS is committed to assuring continued acceptance and success through aggressive product improvement, innovation, and quality. Generations of trade experience and know how NSF LISTED All POWERS ProSeries Faucets and Pre-Rinse Assemblies are certified by NSF International. QUALITY CRAFTSMANSHIP Faucets and Pre-Rinse Assemblies are individually and completely pressure tested to assure customer satisfaction. POWERS is so assured of the durability of the ENCORE Series, that we are providing a One Year Warranty on all Faucets. DESIGN INNOVATION-ideal for customizing The stylish and contemporary POWERS Pre-Rinse Assemblies and Faucets have been designed to stand up to the most rigorous industry use. One of the most important features of the POWERS line is its ability to mix and match components in virtually any combination to meet even the most unique design specification or requirement. AVAILABLE FROM STOCK POWERS is committed to maintaining an inventory of ProSeries plumbing products to assure immediate shipment of these items from stock. WIDE ARRAY OF MODELS AND ACCESSORIES POWERS Pre-Rinse Assemblies are available in both wall and deck mount models with a variety of optional accessories. We invite you to explore our complete plumbing catalogue. POWERS... out to revolutionize the plumbing industry. C2

POWERS Plumbing Products Protected by Antimicrobial-Treated Products Many of the products in this catalogue can be permanently protected with POWERS antimicrobial treatment. Using a patented, proven technology, POWERS is able to treat many of its products and afford its customers a level of protection from the spread of bacteria never available before. These plumbing and hardware products utilize AgION s silver ion technology combined with a uniquely formulated powder coating material to stop bacterial growth in its tracks. If bacteria cannot grow, it cannot survive. Many contact surfaces in the kitchen and wash rooms can now be used in the fight to prevent the spread of harmful, and sometimes deadly, microbes. Contact POWERS to see how SANIGUARD can work for you. Antimicrobial protection for the life of our products SANIGUARD s antimicrobial technology is inorganic. What that means is that with proper care, the antimicrobial protection can last the life of our products. No organic antimicrobial company can say that. Quality you can depend on from a company you can trust. SANIGUARD products are supplied by POWERS which means uncompromising service, selection and quality are guaranteed. SANIGUARD has been certified by NSF to NSF STD 51. SANI- GUARD treated products are listed under NSF STD 2 and STD 61. C3

PRE-RINSE ASSEMBLIES AND FAUCETS Exclusive feature and troublefre Heavy duty, stainless steel, flexible protective hose shield Patented Wall Bracket permanently secures Pre-Rinse Hose Assembly to wall. This unique feature reduces installation time and prevents field abuse U.S. PATENT NO. 5,624,074/ 5,722,595, / 5,749,179 Exclusive 3-ply nylon reinforced high pressure Santoprene hose is permanently secured with high pressure hydraulic fittings power tested to 400 psi All Pre-Rinse Handles now come standard with SANIGUARD Antimicrobial Protection. All Pre-Rinse Grips now come standard with SANIGUARD Antimicrobial Protection. All ENCORE Hose Assemblies are now totally washer-less throughout, adding additional longevity. Temperature resistant O-rings offer a positive leak proof seal O-RING O-RING Heavy thermoplastic reinforced face plate prevents flexing and premature bumper wear...each Pre-Rinse is furnished with three different spray faces: 3.3 gpm at 60 psi Full Spray, a 1.6 gpm at 60 psi Water Saver Flat Spray and a 1.2 gpm at 60 psi Energy Saver Spray certified to ASTM F2324-03, in accordance with the Energy Policy Act of 2005. Heavy- duty gooseneck spring...heat treated, triple chrome plated, insures convenient hose position and flexibility Non-marring, dish sensitive, impact resistant bumper engineered to offer a positive, non-leaking, lip tight seal...heat resistant material will not fatigue under extreme hot temperatures Patented, heavy-duty, solid stainless steel strain relief spring transfers load stress and distributes it evenly over extended area...significantly improves hose life (also available with optional stainless steel gooseneck spring) C4

s for durability e performance INSTITUTIONAL, SPECIFICATION GRADE Provided with comfortable user-friendly handles and international colour coded indicators Heavy gauge solid brass tubular spout has triple plated chromium finish Brass spout bushings with exclusive high temperature resistant, self-lubricating, EPDM O-rings and internal shoulder...maximizes spout stability, prevents spout leakage All Faucet handles now come standard with SANIGUARD Antimicrobial Protection. Heavy- duty self-centering mounting flange provides for fast, convenient installation Optional quarter turn ceramic valve with built-in check valve also available Unique stem valve prevents water cross flow between hot and cold water, and prevents back flow siphoning Solid brass precision casting... hydraulically pressure tested to insure integrity... triple plated highly polished nickel chromium finish All ProSeries faucets are furnished with both a water conservation aerator and a screen bubbler spout tip at no additional charge. *Optional aerators available All ProSeries Faucets and Pre-Rinse Assemblies are equipped with full on quarter turn valves offering full volume water flow Exclusive solid brass valve seat accepts conventional faucet bibb washer...minimizes down time and costly service calls Excellence in engineering inside and out C5

Pre-rinse Assemblies & Faucets OPTIONAL ACCESSORIES KN55 SERIES ADD-ON FAUCET WITH SWING SPOUT Extends flexibility of Pre-Rinse Assemblies by providing additional swivel spout capability. Permits full spout swing without interference with riser pipe. Installation is easy, utilizing same water lines and controls as the Pre-Rinse. Separate valve is used to control spout flow. SEE PAGE C15 FOR DETAILS K50-Y500 OPTIONAL HEAVY-DUTY SWIVEL ARM SUPPORT Easily mounts to Riser Pipe and Swivel Arm. Allows full swing while providing additional support when Pre-Rinse is exposed to severe field use. SEE PAGE C14 FOR DETAILS KN50-1000-BR KN53-1000-BR KN50 DECK MOUNT PRE-RINSE ASSEMBLY KN53 WALL MOUNT PRE-RINSE ASSEMBLY KN50-1000-BR (with Wall Bracket-as shown) KN50-1000 (without Wall Bracket) 8"(200mm) ADJUSTABLE CENTRES KN53-1000-BR (with Wall Bracket as shown) KN53-1000 (without Wall Bracket) FURNISHED WITH 1/2" NPS MALE INLETS ON 4"(100mm) CENTRES WITH 1/4" NPT UNION TAILPIECES AND MOUNTING HARDWARE Pre-Rinse Assembly is approximately 38"(965mm) high with a clearance height from underside of Pre-Rinse Spray Head to base of faucet of 10" (254mm) and an overhang projection distance from centre-line of faucet to centre-line of spray head assembly of 15"(381mm). FURNISHED WITH 1/2" NPT FEMALE INLETS Pre-Rinse Assembly is approximately 35"(890mm) high with a clearance height from underside of Pre-Rinse Spray Head to centre-line of faucet of 7"(178mm) and an overhang projection distance from centre-line of faucet to centre-line of spray head assembly of 15"(381mm). AVAILABLE WITH CERAMIC VALVES ALL MODELS SHOWN WITH OPTIONAL WALL BRACKET #K50-Y020 FOR A COMPLETE LINE OF OPTIONAL ACCESSORIES SEE PAGES C14 AND C15 C6

Pre-rinse Assemblies & Faucets OPTIONAL ACCESSORIES KN55 SERIES ADD-ON FAUCET WITH SWING SPOUT Extends flexibility of Pre-Rinse Assemblies by providing additional swivel spout capability. Permits full spout swing without interference with riser pipe. SEE PAGE C15 FOR DETAILS K50-Y020 OPTIONAL WALL BRACKET Assembly includes 12" nipple which may be cut to permit adjustments between 2" and 12". SEE PAGE C14 FOR DETAILS KN50-Y051 SWIVEL JOINT Allows hose to swivel 360 on swivel arm pre-rinse. K50-5026-12 K53-5026-12 K50 SERIES DOUBLE PANTRY SWIVEL ARM PRE-RINSE ASSEMBLY K53 SERIES WALL MOUNT SWIVEL ARM PRE-RINSE ASSEMBLY K50-5026-12* (with 12"(304mm) Swivel Arm-as shown) K50-5032-18** (with 18"(457mm) Swivel Arm) K53-5026-12* (with 12"(304mm) Swivel Arm-as shown) K53-5032-18** (with 18"(457mm) Swivel Arm) Heavy gauge swivel arm mated to a solid forged swivel elbow, designed to withstand the demands of commercial applications Available with 12" or 18" swing arm offering a full 360 rotation Furnished with both a conventional pattern spray head as well as exclusive water saver spray head Wall Bracket included Includes a spray head hook which holds spray head away from work area when not in use Provides fast, secure installation Nylon reinforced hose is protected by heavy gauge, stainless steel shield complete with exclusive strain relief spring, insuring long product life *12" Pre-Rinse Assembly is approximately 33"(838mm) high with a clearance height from underside of Pre-Rinse Spray Head to base of faucet of 4"(102mm) and an overhang projection distance from centre-line of faucet to centre-line of spray head assembly of 12"(305mm). **18" Pre-Rinse Assembly is approximately 39"(991mm) high with a clearance height from underside of Pre-Rinse Spray Head to base of faucet of 4"(102mm) and an overhang projection distance from centre-line of faucet to centre-line of spray head assembly of 18"(457mm). *#K53-5026-12-Pre-Rinse Assembly is approximately 30"(762mm) high with a clearance height from underside of Pre-Rinse Spray Head to base of faucet of 1"(25.4mm) and an overhang projection distance from centre-line of faucet to centre-line of spray head assembly of 12"(305mm). **#K53-5032-18-Pre-Rinse Assembly is approximately 36"(914mm) high with a clearance height from underside of Pre-Rinse Spray Head to base of faucet of 1"(25.4mm) and an overhang projection distance from centre-line of faucet to centre-line of spray head assembly of 18"(457mm). SWIVEL ARM PRE-RINSE ASSEMBLIES FURNISHED WITH WALL BRACKET #K50-Y020...SHOWN WITH OPTIONAL SWIVEL ARM SUPPORT #K50-Y500 AVAILABLE WITH CERAMIC VALVES FOR A COMPLETE LINE OF OPTIONAL ACCESSORIES SEE PAGES C14 AND C15 C8

Institutional quality, specification grade Stress resistant hose for long life Heat treated riser spring PRE-RINSE ASSEMBLIES Built-in check valves Contemporary design Designed for customizing K56-5026-12 K56 SERIES DECK MOUNT SWIVEL ARM PRE-RINSE ASSEMBLY 4"(100mm) ADJUSTABLE CENTRES K56-5026-12 with 12"(304mm) Swivel Arm-as shown K56-5032-18 with 18"(457mm) Swivel Arm Heavy gauge swivel arm mated to a solid forged swivel elbow, designed to withstand the demands of commercial applications Available with 12" or 18" swing arm offering a full 360 rotation Furnished with both a conventional pattern spray head as well as exclusive water saver spray head Wall Bracket included 12" Pre-Rinse Assemblies are approximately 33"(838mm) high with a clearance height from underside of Pre-Rinse Spray Head to base of faucet of 4"(102mm) and an overhang projection distance from centre-line of faucet to centre-line of spray head assembly of 12"(305mm). K60-5026-12 K60 SERIES DECK MOUNT SWIVEL ARM PRE-RINSE ASSEMBLY 8"(200mm) ADJUSTABLE CENTRES K60-5026-12 with 12"(304mm) Swivel Arm-as shown K60-5032-18 with 18"(457mm) Swivel Arm Provides fast, secure installation Includes a spray head hook which holds spray head away from work area when not in use Nylon reinforced hose is protected by heavy gauge, stainless steel shield complete with exclusive strain relief spring, insuring long product life 18" Pre-Rinse Assemblies are approximately 39"(991mm) high with a clearance height from underside of Pre-Rinse Spray Head to base of faucet of 4"(102mm) and an overhang projection distance from centre-line of faucet to centre-line of spray head assembly of 18"(457mm). SWIVEL ARM PRE-RINSE ASSEMBLIES FURNISHED WITH WALL BRACKET #K50-Y020...SHOWN WITH OPTIONAL SWIVEL ARM SUPPORT #K50-Y500 AVAILABLE WITH CERAMIC VALVES FOR A COMPLETE LINE OF OPTIONAL ACCESSORIES SEE PAGES C14 AND C15 C9

Pre-rinse Assemblies & Faucets KN63-1000-BR KN63-1000-BRMV* KN69-1000-BR KN63 SERIES SINGLE DECK MOUNT PRE-RINSE ASSEMBLY KN69 SERIES SINGLE WALL MOUNT PRE-RINSE ASSEMBLY KN63-1000-BR (with Wall Bracket-as shown) KN63-1000 (without Wall Bracket) KN69-1000-BR (with Wall Bracket-as shown) KN69-1000 (without Wall Bracket) FURNISHED WITH 1/2" NPS MALE INLET, 1/4" NPT UNION TAILPIECE AND MOUNTING HARDWARE. Pre-Rinse Assembly is approximately 38"(965mm) high with a clearance height from underside of pre-rinse spray head to base of faucet of 10"(254mm) and an overhang projection distance from centre-line of faucet to centre-line of spray head assembly of 15"(381mm). FURNISHED WITH 1/2" NPS NIPPLE AND MOUNTING HARDWARE. Pre-Rinse Assembly is approximately 35"(890mm) high with a clearance height from underside of pre-rinse spray head to centre-line of faucet of 7"(178mm) and an overhang projection distance from centre-line of faucet to centre-line of spray head assembly of 15"(381mm). *KN63 SERIES CAN BE FURNISHED COMPLETE WITH TEMPERATURE MIXING VALVE AS SHOWN. ADD SUFFIX...MV...TO ALL MODELS SHOWN WITH OPTIONAL WALL BRACKET #K50-Y020 AVAILABLE WITH CERAMIC VALVES FOR A COMPLETE LINE OF OPTIONAL ACCESSORIES SEE PAGES C14, C15 C10

Institutional quality, specification grade Stress resistant hose for long life Heat treated riser spring PRE-RINSE ASSEMBLIES Built-in check valves Contemporary design Designed for customizing OPTIONAL ACCESSORIES KN55 SERIES ADD-ON FAUCET WITH SWING SPOUT Extends flexibility of Pre-Rinse Assemblies by providing additional swivel spout capability. Permits full spout swing without interference with riser pipe. Installation is easy, utilizing same water lines and controls as the Pre-Rinse. Separate valve is used to control spout flow. SEE PAGE C15 FOR DETAILS K50-Y020 OPTIONAL WALL BRACKET Assembly includes 12" nipple which may be cut to permit adjustments between 2" and 12". New patented compression fitting allows fast, positive connection. SEE PAGE C14 FOR DETAILS KN71-1000-BR KN73-1000-BR KN71 SERIES BASE WALL MOUNT PRE-RINSE ASSEMBLY KN73 SERIES BASE DECK MOUNT PRE-RINSE ASSEMBLY KN71-1000-BR (with Wall Bracket-as shown) KN71-1000 (without Wall Bracket) KN73-1000-BR (with Wall Bracket-as shown) KN73-1000 (without Wall Bracket) FURNISHED WITH 1/2" NPT FEMALE INLET, 1/2" NIPPLE ELL AND MOUNTING HARDWARE. FURNISHED WITH 1/2" NPS MALE INLET AND MOUNTING HARDWARE. Pre-Rinse Assembly is approximately 35"(890mm) high with a clearance height from underside of pre-rinse spray head to centre-line of faucet of 7"(178mm) and an overhang projection distance from centre-line of faucet to centre-line of spray head assembly of 15"(381mm). Pre-Rinse Assembly is approximately 35"(890mm) high with a clearance height from underside of pre-rinse spray head to base of faucet of 7"(178mm) and an overhang projection distance from centre-line of faucet to centre-line of spray head assembly of 15"(381mm). ALL MODELS SHOWN WITH OPTIONAL WALL BRACKET #K50-Y020 AVAILABLE WITH CERAMIC VALVES FOR A COMPLETE LINE OF OPTIONAL ACCESSORIES SEE PAGES C14, C15 C11

Pot Fillers DECK and WALL MOUNT POT FILLERS with SWIVEL HOSE, HOOKED SPRAY VALVE and WALL HOOK Available with or without Vacuum Breaker ALL MODELS SHOWN WITH RECOMMENDED VACUUM BREAKER BUILT-IN CHECK VALVES 72"(1828mm) LONG STAINLESS STEEL FLEXIBLE HOSE PLASTIC COATED WALL HOOK WITH CHROME PLATED BASE - 1/2" NPT FEMALE INLETS MODEL KN53-3000-VB WALL MOUNT POT FILLER 8"(200mm) ADJUSTABLE CENTRES SINGLE WALL MOUNT POT FILLER WALL MOUNT BASE POT FILLER DOUBLE PANTRY POT FILLER KN53-3000-VB (with VACUUM BREAKER) KN53-3000 (without VACUUM BREAKER) KN69-3000-VB (with VACUUM BREAKER) KN69-3000 (without VACUUM BREAKER) FURNISHED WITH MOUNTING HARDWARE. KN71-3000-VB (with VACUUM BREAKER) KN71-3000 (without VACUUM BREAKER) FURNISHED WITH MOUNTING HARDWARE. NOTE: CHECK VALVE NOT SUPPLIED WITH THIS MODEL. KN50-3000-VB (with VACUUM BREAKER) KN50-3000 (without VACUUM BREAKER) FURNISHED WITH 1/4" UNION TAILPIECES AND MOUNTING HARDWARE. SINGLE PANTRY POT FILLER DECK MOUNT BASE POT FILLER DECK MOUNT POT FILLER 4"(100mm) ADJUSTABLE CENTRES DECK MOUNT POT FILLER 8"(200mm) ADJUSTABLE CENTRES KN63-3000-VB (with VACUUM BREAKER) KN63-3000 (without VACUUM BREAKER) KN73-3000-VB (with VACUUM BREAKER) KN73-3000 (without VACUUM BREAKER) KN56-3000-VB (with VACUUM BREAKER) KN56-3000 (without VACUUM BREAKER) KN60-3000-VB (with VACUUM BREAKER) KN60-3000 (without VACUUM BREAKER) FURNISHED WITH 1/4" UNION TAILPIECES AND MOUNTING HARDWARE. FURNISHED WITH 1/4" NPT UNION TAILPIECE AND MOUNTING HARDWARE. NOTE: CHECK VALVE NOT SUPPLIED WITH THIS MODEL. FURNISHED WITH 1/2" NIPPLES AND MOUNTING HARDWARE. FURNISHED WITH 1/2" NIPPLES AND MOUNTING HARDWARE. MIXING VALVE AVAILABLE SEE PAGE C33 C12

Utility Sprays ALL MODELS SHOWN WITH RECOMMENDED VACUUM BREAKER DECK and WALL MOUNT UTILITY SPRAYS with SWIVEL HOSE, ANGLED SPRAY VALVE and WALL HOOK Available with or without Vacuum Breaker MODEL KN53-2000-VB BUILT-IN CHECK VALVES 72"(1828mm) LONG STAINLESS STEEL FLEXIBLE HOSE PLASTIC COATED WALL HOOK WITH CHROME PLATED BASE - 1/2" NPT FEMALE INLETS WALL MOUNT UTILITY SPRAY 8"(200mm) ADJUSTABLE CENTRES SINGLE WALL MOUNT UTILITY SPRAY WALL MOUNT BASE UTILITY SPRAY DOUBLE PANTRY UTILITY SPRAY KN53-2000-VB (with VACUUM BREAKER) KN53-2000 (without VACUUM BREAKER) KN69-2000-VB (with VACUUM BREAKER) KN69-2000 (without VACUUM BREAKER) FURNISHED WITH MOUNTING HARDWARE. KN71-2000-VB (with VACUUM BREAKER) KN71-2000 (without VACUUM BREAKER) FURNISHED W/ MOUNTING HARDWARE. NOTE: CHECK VALVE NOT SUPPLIED WITH THIS MODEL KN50-2000-VB (with VACUUM BREAKER) KN50-2000 (without VACUUM BREAKER) FURNISHED WITH 1/2" NPS NIPPLES AND MOUNTING HARDWARE. SINGLE PANTRY UTILITY SPRAY DECK MOUNT BASE UTILITY SPRAY DECK MOUNT UTILITY SPRAY 4"(100mm) ADJUSTABLE CENTRES DECK MOUNT UTILITY SPRAY 8"(200mm) ADJUSTABLE CENTRES KN63-2000-VB (with VACUUM BREAKER) KN63-2000 (without VACUUM BREAKER) FURNISHED WITH 1/4" NPT UNION TAILPIECE AND MOUNTING HARDWARE. KN73-2000-VB (with VACUUM BREAKER) KN73-2000 (without VACUUM BREAKER) FURNISHED WITH 1/4" NPT UNION TAILPIECE AND MOUNTING HARDWARE. NOTE: CHECK VALVE NOT SUPPLIED WITH THIS MODEL. TEMPERATURE MIXING VALVE AVAILABLE..PG C38 KN56-2000-VB (with VACUUM BREAKER) KN56-2000 (without VACUUM BREAKER) FURNISHED WITH 1/2" NPS NIPPLES AND MOUNTING HARDWARE. KN60-2000-VB (with VACUUM BREAKER) KN60-2000 (without VACUUM BREAKER) FURNISHED WITH 1/2" NIPPLES AND MOUNTING HARDWARE. AVAILABLE WITH CERAMIC VALVES KN50-Y025... 90 SWIVEL ELBOW for use with vacuum breaker hose ass y. (shown on C14) in utility spray and pot filler applications. C13

Pre-Rinse Accessories U.S. PATENT NO. 5,749,179 WALL HOOK K50-Y012 Permits spray valves to be conveniently hung in place when not in use. Furnished with chrome plated base and coated hook. WALL BRACKET K50-Y020 Assembly includes 12"(300mm) nipple which may be cut to permit adjustments between 2" and 12"(50mm and 300mm). New patented compression fitting allows fast, positive connection. SPRAY VALVE KITS LOW FLOW (1.2 GPM @ 60PSI) PRE-RINSE KIT WITH SANIGUARD ANTIMICROBIAL KN50-0220-12 Pre-Rinse Spray Assembly complete with grip and adapters to fit other manufacturer s hoses. HEAVY-DUTY SWIVEL ARM SUPPORT K50-Y500 Easily mounts to riser pipe and swivel arm. Allows full swing while providing additional support when Pre-Rinse is exposed to severe field use. MOUNTING KITS 45 SUPPLY INLET K50-Y047 Male inlet for use with 45 mounting surface. 1/2" male IPS. UNIVERSAL PRE-RINSE REPLACEMENT KIT WITH SANIGUARD ANTIMICROBIAL KN50-0220 Pre-Rinse Spray Assembly complete with grip and adapters to fit other manufacturer s hoses. SELECT-A-SPRAY PRE-RINSE KIT WITH SANIGUARD ANTIMICROBIAL KN50-0210 Pre-Rinse Spray Assembly complete with grip and adapters to fit other manufacturer s hoses. SPRAY VALVE ASSEMBLIES WALL FAUCET MOUNTING KIT KN40-1000 Kit has been designed for simple installation of wall faucets within the standard backsplash space. Contains two each of 1/2" NPS nipples, 1/2" NPT x 1/2" sweat ells, washers and locknuts. HOSE ASSEMBLIES DECK FAUCET MOUNTING KIT KN60-Y010 Kit has been designed for simple installation of deck faucets. Contains two each of 1/2" NPS nipples, washers and locknuts. U.S. PATENT NO. 5,624,074, 5,722,595 A B C A. PRE-RINSE SPRAY VALVE ASSEMBLY KN50-Y002 B. ANGLED SPRAY VALVE ASSEMBLY KN50-Y030 C. POT FILLER SPRAY VALVE ASSEMBLY KN50-Y031 44" (1100mm) HOSE ASSEMBLY WITH CONTINUOUS PRESSURE IN-LINE VACUUM BREAKER K50-Y016-44 For use on Pre-Rinse units where additional backflow prevention is desirable. Prevents the flow of contaminated water into the safe water drinking supply.. SELECT-A-SPRAY ADJUSTABLE 5 PATTERN SPRAY HEAD KN50-Y102 Includes 5 different spray patterns. Retrofits all makes of pre-rinses. 90 SWIVEL ELBOW FOR USE WITH VACUUM BREAKER HOSE ASS Y. in utility spray and pot filler applications... KN50-Y025 Constructed with a strong, flexible stainless steel outer casing over a nylon reinforced rubber core, the POWERS Pre-Rinse Hose has been especially designed to significantly minimize any incidence of failure. At the point where most other hoses fail, POWERS has added a strain relief coil of.125 (3mm) diameter chrome plated wire. This special coil transfers the load stress away from the part of the hose most subject to flexing and distributed it evenly over an extended area, thus adding significantly to the life of the hose. WITH GRIP KN50-Y004-20 KN50-Y004-26 KN50-Y004-44 KN50-Y004-60 KN50-Y004-72 KN50-Y004-96 LENGTH 20"(500mm) 26"(650mm) 44"(1100mm) 60"(1500mm) 72"(1800mm) 96"(2400mm) WITHOUT GRIP KN50-Y010-20 KN50-Y010-26 KN50-Y010-44 KN50-Y010-60 KN50-Y010-72 KN50-Y010-96 KN50-X025 GRIP ONLY ALL HOSES AVAILABLE WITH OPTIONAL VACUUM BREAKERS LENGTH 14"(355mm) 20"(508mm) 38"(965mm) 54"(1371mm) 66"(1676mm) 90"(2286mm) OTHER LENGTHS AVAILABLE ON APPLICATION. 44" (1100mm) IS THE STANDARD LENGTH ON ALL ENCORE PRE-RINSE UNITS C14

Faucet & Pre-Rinse Accessories FAUCET HANDLES CHROME PLATED DESIGNER HANDLES K50-X117 (1-PAIR) Add-On Faucet extends flexibility of Pre-Rinse Assemblies by providing additional swivel spout capability. The only Add-On Faucet designed specifically to permit full spout swing without interference with riser pipe. Installation is easy, utilizing same water lines and controls as the Pre- Rinse. Separate valve is used to control spout flow. AVAILABLE WITH CERAMIC VALVES ADD-ON FAUCETS KN55 SERIES ADD-ON FAUCET with SWING SPOUTS KN55-7006 KN55-7008 KN55-7010 KN55-7012 KN55-7014 KN55-7016 SPOUT LENGTH 6"(150mm) 8"(200mm) 10"(250mm) 12"(300mm) 14"(350mm) 16"(400mm) Chrome plated acrylic in smart, contemporary design. Smooth, secure grip. May be used on any ProSeries Faucet or Pre-Rinse Unit. CROSS HANDLE REPLACEMENT KIT K50-0111 (1-PAIR) Chrome plated Cross Handles are available for all ProSeries Faucets and Pre-Rinse Units. Kit includes two handles, hot and cold indicators and screws. SUPPLY INLETS ADJUSTABLE SUPPLY INLETS Choice of inlets permit easy fast installation by providing adjustability of different faucet or pre-rinse centres to match varying installation (piping) centres. ProSeries REPAIR KITS REPLACEMENT VALVE ASSEMBLY KN60-Y004 DESCRIPTION KN33 SERIES KN34-Y007 SINGLE VALVE ASS Y. KN34 SERIES KN34-Y006 COLD VALVE ASS Y. KN34-Y007 HOT VALVE ASS Y. KN35 SERIES KN35-Y007 ADD-ON VALVE ASS Y. KN60-Y005 ECCENTRIC TOTAL RANGE (2) INLETS KN60-Y004 1/2"(12mm) 1"(25mm) KN60-Y005 1"(25mm) 2"(50mm) KN60-Y006* NONE N/A KN41-Y006 KN41-Y007 DESCRIPTION KN41 & KN45 SERIES COLD VALVE ASS Y. HOT VALVE ASS Y. KN50 SERIES* KN50-Y006 COLD VALVE ASS Y. KN50-Y007 HOT VALVE ASS Y. KN55 SERIES KN55-Y011 COLD VALVE ASS Y. KN55-Y010 HOT VALVE ASS Y. KN60-Y006 *KN60-Y006 is supplied on all ProSeries Wall Mount Faucets and Pre-Rinse units. **Each Inlet also provides an additional plus or minus 1/4"(6mm) compensation to accommodate varying field conditions. *AVAILABLE WITH CERAMIC VALVES... ADD SUFFIX - CCV TO PART NUMBER WRIST BLADE HANDLES 4 INCH, K50-0001 (1-PAIR) 6 INCH, K50-0001-6 Solid brass chrome plated Wrist Blades are available for Deck and Wall Mount Faucets. Kit includes two blades, hot and cold indicators and screws. K11 SERIES utilizes optional MODEL NO. K11-0001 WRIST BLADE HANDLES SPOUT EXTENSION FAUCET HANDLE REPAIR KIT K50-0110 UNIVERSAL BUTTON VALVE ASSEMBLY KN50-Y027 Kit contains all parts to completely replace Pre-Rinse Button Valve Assembly or Knee/ Foot Valve Assembly PRE-RINSE SPRAY VALVE REPAIR KIT KN50-0200 REPLACEMENT SPRING 6" KN11-X106 12" KN11-X112 Adds flexibility to accommodate almost any Swivel Spout length requirement. Fits all ProSeries Faucets accepts all ProSeries Swivel Spouts. CONVENTIONAL CHROME PLATED REPLACEMENT SPRING K50-X033 Heavy-duty Gooseneck Spring, heat treated, nickel plated... insures convenient hose position and flexibility. HEAVY- DUTY STAINLESS STEEL REPLACEMENT SPRING K50-X178 Solid Stainless Steel Gooseneck Spring, heat treated, insures convenient hose position and flexibility. C15

Wall Mount Faucets KN54 SERIES WALL MOUNT FAUCETS with SWING SPOUTS KN54 SERIES WALL MOUNT FAUCETS 8" (200mm) ADJUSTABLE CENTRES with SWING SPOUTS KN54-8006 KN54-8008 KN54-8010 KN54-8012 KN54-8014 KN54-8016 SPOUT LENGTH 6" (150mm) 8" (200mm) 10" (250mm) 12" (300mm) 14" (350mm) 16" (400mm) SPOUT LENGTH 2-5/8" (66mm) SPOUT LENGTH FAUCETS FURNISHED WITH BOTH OPTIONAL AERATOR AND BUBBLER SCREEN. AVAILABLE WITH CERAMIC VALVES. 3-1/4"(82mm) 1/2" NPT FEMALE INLETS For a Complete Selection of Optional Accessories see pages C14 and C15 WALL FAUCET MOUNTING KIT KN40-1000 Designed for simple installation of wall faucets within the standard backsplash space. Contains two each of 1/2"NPS nipples, 1/2" NPT x 1/2" sweat ells, washers and locknuts. 45 SUPPLY INLET K50-Y047 Male inlet for use with 45 mounting surface. 1/2" male IPS. ADJUSTABLE SUPPLY INLETS MODEL NO S. KN60-Y004/5/6 Choice of inlets permit easy fast installation by providing adjustability of different faucet or pre-rinse centres to match varying installation (piping) centres. C16

Wall Mount Faucets KN54 SERIES WALL MOUNT FAUCETS with SWIVEL and RIGID GOOSENECK SPOUTS and DOUBLE JOINTED SPOUTS KN54 SERIES WALL MOUNT FAUCETS 8"(200mm) ADJUSTABLE CENTRES with SWIVEL GOOSENECK SPOUTS A B C KN54-8000 3-1/2"(90mm) 9"(230mm) 6-3/8"(160mm) KN54-8001 8-1/2"(215mm) 12-3/4"(325mm) 7"(180mm) KN54-8002 6"(150mm) 10-1/4"(260mm) 6-1/4"(160mm) with RIGID GOOSENECK SPOUTS KN54-8000-R 3-1/2"(90mm) 9"(230mm) 6-3/8"(160mm) KN54-8001-R 8-1/2"(215mm) 12-3/4"(325mm) 7"(180mm) KN54-8002-R 6"(150mm) 10-1/4"(260mm) 6-1/4"(160mm) 2-5/8" (66mm) C B A 3-1/4"(82mm) 1/2" NPT FEMALE INLETS KN54 SERIES WALL MOUNT FAUCET 8"(200mm) ADJUSTABLE CENTRES with DOUBLE JOINTED SPOUT 12" (300mm) 2-5/8" (66mm) 6" (150mm) KN54-8018 SPOUT LENGTH 18"(450mm) 1/2" NPT FEMALE INLETS FAUCETS FURNISHED WITH BOTH OPTIONAL AERATOR AND BUBBLER SCREEN. AVAILABLE WITH CERAMIC VALVES Optional Accessories CHROME PLATED DESIGNER HANDLES K50-X117 (1-PAIR) Smooth, secure grip, may be used on any ProSeries Faucet or Pre-Rinse unit. CROSS HANDLE REPLACEMENT KIT K50-0111 (1-PAIR) Chrome plated Cross Handles are available for all ProSeries Faucets and Pre Rinse Units. Kit includes two handles, hot and cold indicators and screws. WRIST BLADE HANDLES 4 INCH, K50-0001 (1-PAIR) 6 INCH, K50-0001-6 Solid brass chrome plated, available for deck and wall mount faucets. Kit includes Two Blades, Hot and Cold Buttons and Screws. C17

Deck Mount Faucets KN57, KN61 and KN67 SERIES DECK MOUNT FAUCETS with SWING SPOUTS KN57 SERIES DECK MOUNT FAUCETS 4" (100mm) ADJUSTABLE CENTRES with SWING SPOUTS KN57-4006 KN57-4008 KN57-4010 KN57-4012 KN57-4014 KN57-4016 SPOUT LENGTH 6"(150mm) 8"(200mm) 10"(250mm) 12"(300mm) 14"(350mm) 16"(400mm) KN61 SERIES DECK MOUNT FAUCETS 8" (200mm) ADJUSTABLE CENTRES with SWING SPOUTS SPOUT LENGTH KN61-8006 KN61-8008 KN61-8010 KN61-8012 KN61-8014 KN61-8016 6"(150mm) 8"(200mm) 10"(250mm) 12"(300mm) 14"(350mm) 16"(400mm) FAUCETS FURNISHED WITH BOTH OPTIONAL AERATOR AND BUBBLER SCREEN. AVAILABLE WITH CERAMIC VALVES. FURNISHED WITH 1/2" NPS MOUNTING HARDWARE SPOUT LENGTH KN67 SERIES DECK MOUNT FAUCETS 6" (150mm) ADJUSTABLE CENTRES with SWING SPOUTS SPOUT LENGTH KN67-6006 KN67-6008 KN67-6010 KN67-6012 KN67-6014 KN67-6016 Optional Accessories 6"(150mm) 8"(200mm) 10"(250mm) 12"(300mm) 14"(350mm) 16"(400mm) ADJUSTABLE SUPPLY INLETS MODEL NO'S. KN60-Y004/5/6 Choice of inlets permit easy fast installation by providing adjustability of different faucet or Pre-Rinse centres to match varying installation (piping) centres. CHROME PLATED DESIGNER HANDLES K50-X117 (1-PAIR) Smooth, secure grip, may be used on any ProSeries Faucet or Pre-Rinse unit. FOR A COMPLETE LINE OF OPTIONAL ACCESSORIES SEE PAGE C14 AND C15 C18

Deck Mount Faucets KN57, KN61 and KN67 SERIES DECK MOUNT FAUCETS with SWIVEL and RIGID GOOSENECK SPOUTS and DOUBLE JOINTED SPOUTS KN57 SERIES DECK MOUNT FAUCETS 4"(100mm) ADJUSTABLE CENTRES with SWIVEL GOOSENECK SPOUTS A B C KN57-4000 3-1/2"(90mm) 11-7/8"(300mm) 9-1/4"(235mm) KN57-4001 8-1/2"(215mm) 15-3/4"(400mm) 10"(255mm) KN57-4002 6"(150mm) 12-3/4"(320mm) 9"(230mm) with RIGID GOOSENECK SPOUTS KN57-4000-R 3-1/2"(90mm) 11-7/8"(300mm) 9-1/4"(235mm) KN57-4001-R 8-1/2"(215mm) 15-3/4"(400mm) 10"(255mm) A C B KN57-4002-R 6"(150mm) 12-3/4"(320mm) 9"(230mm) KN61 SERIES DECK MOUNT FAUCETS 8"(200mm) ADJUSTABLE CENTRES with SWIVEL GOOSENECK SPOUTS A B C KN61-8000 3-1/2"(90mm) 11-7/8"(300mm) 9-1/4"(235mm) KN61-8001 8-1/2"(215mm) 15-3/4"(400mm) 10"(255mm) KN61-8002 6"(150mm) 12-3/4"(320mm) 9"(230mm) B A with RIGID GOOSENECK SPOUTS KN61-8000-R 3-1/2"(90mm) 11-7/8"(300mm) 9-1/4"(235mm) C KN61-8001-R 8-1/2"(215mm) 15-3/4"(400mm) 10"(255mm) KN61-8002-R 6"(150mm) 12-3/4"(320mm) 9"(230mm) KN67 SERIES DECK MOUNT FAUCETS 6"(150mm) ADJUSTABLE CENTRES with SWIVEL GOOSENECK SPOUTS A B C KN67-6000 3-1/2"(90mm) 11-7/8"(300mm) 9-1/4"(235mm) KN67-6001 8-1/2"(215mm) 15-3/4"(400mm) 10"(255mm) KN67-6002 6"(150mm) 12-3/4"(320mm) 9"(230mm) with RIGID GOOSENECK SPOUTS KN67-6000-R 3-1/2"(90mm) 11-7/8"(300mm) 9-1/4"(235mm) KN67-6001-R 8-1/2"(215mm) 15-3/4"(400mm) 10"(255mm) KN67-6002-R 6"(150mm) 12-3/4"(320mm) 9"(230mm) 12" (300mm) 6" (150mm) FAUCETS FURNISHED WITH BOTH OPTIONAL AERATOR AND BUBBLER SCREEN. AVAILABLE WITH CERAMIC VALVES. KN57 / KN61 / KN67 SERIES DECK MOUNT FAUCETS with DOUBLE JOINTED SPOUTS ADJ. CENTRES SPOUT LENGTH KN57-4018 4" (100mm) 18" (450mm) KN67-6018 6" (150mm) 18" (450mm) KN61-8018 8" (200mm) 18" (450mm) NOTE: ALL KN57/ KN61/ KN67 SERIES FAUCETS HAVE 1/2" NPT FEMALE INLETS AND ARE FURNISHED COMPLETE WITH 1/2" NIPPLES AND MOUNTING HARDWARE. CROSS HANDLE REPLACEMENT KIT K50-0111 (1-PAIR) Chrome plated Cross Handles are available for all ProSeries Faucets and Pre Rinse Units. Kit includes two handles, hot and cold indicators and screws. WRIST BLADE HANDLES 4 INCH, K50-0001 (1-PAIR) 6 INCH, K50-0001-6 Solid brass chrome plated, available for deck and wall mount faucets. Kit includes two blades, hot and cold buttons and screws. C19

Pantry Faucets KN51and KN64 SERIES SINGLE and DOUBLE PANTRY FAUCETS with SWING SPOUTS SPOUT LENGTH KN51 SERIES DOUBLE PANTRY FAUCETS with SWING SPOUTS KN51-9006 KN51-9008 KN51-9010 KN51-9012 KN51-9014 KN51-9016 SPOUT LENGTH 6"(150mm) 8"(200mm) 10"(250mm) 12"(300mm) 14"(350mm) 16"(400mm) NOTE: PROVIDED WITH 1/2" NPS MALE INLET WITH 1/4" NPT UNION TAILPIECES AND MOUNTING HARDWARE. SPOUT LENGTH 1/2" NPS MALE INLET WITH 1/4" NPT UNION TAILPIECE AND MOUNTING HARDWARE. KN64 SERIES SINGLE PANTRY FAUCETS with SWING SPOUTS KN64-9006 KN64-9008 KN64-9010 KN64-9012 KN64-9014 KN64-9016 SPOUT LENGTH 6"(150mm) 8"(200mm) 10"(250mm) 12"(300mm) 14"(350mm) 16"(400mm) NOTE: ALL FAUCETS ARE AVAILABLE WITH TEMPERATURE MIXING VALVE. TO ORDER ADD SUFFIX...MV...TO FAUCETS FURNISHED WITH BOTH OPTIONAL AERATOR AND BUBBLER SCREEN AVAILABLE WITH CERAMIC VALVES FLOW CONTROL ADJUSTMENT SCREWS 1/4" NPT FEMALE OUTLET AND 1/2" NPS MALE INLETS ON 4" CENTRES WITH 1/4" UNION TAILPIECES. For a Complete Selection of Optional Accessories see pages C14 and C15 MIXING VALVE MAY BE ORDERED SEPARATELY. ORDER AS... KN63-Y005 VALVE CONTAINS BUILT-IN ADJUSTABLE FLOW CONTROLS THAT ALLOW FAUCET WATER TEMPERATURE TO BE PRE-SET. CONTAINS BUILT-IN BALL CHECKS. IT CAN BE INSTALLED ON ANY ProSeries DECK MOUNT SINGLE INLET FAUCET OR PRE-RINSE ASSEMBLY. WALL FAUCET MOUNTING KIT KN40-1000 Designed for simple installation of wall faucets within the standard backsplash space. Contains two each of 1/2"NPS nipples, 1/2" NPT x 1/2" sweat ells, washers and locknuts. 45 SUPPLY INLET K50-Y047 Male inlet for use with 45 mounting surface. 1/2" male IPS. ADJUSTABLE SUPPLY INLETS MODEL NO S. KN60-Y004/5/6 Choice of inlets permit easy fast installation by providing adjustability of different faucet or pre-rinse centres to match varying installation (piping) centres. C20

Pantry Faucets KN51 and KN64 SERIES SINGLE and DOUBLE PANTRY FAUCETS with SWIVEL and RIGID GOOSENECK SPOUTS and DOUBLE JOINTED SPOUTS KN51 SERIES DOUBLE PANTRY FAUCETS with SWIVEL GOOSENECK SPOUTS A B C KN51-9000 3-1/2"(90mm) 11-7/8"(300mm) 9-1/4"(235mm) KN51-9001 8-1/2"(215mm) 15-3/4"(400mm) 10"(255mm) KN51-9002 6"(150mm) 12-3/4"(320mm) 9"(230mm) with RIGID GOOSENECK SPOUTS B A C KN51-9000-R 3-1/2"(90mm) 11-7/8"(300mm) 9-1/4"(235mm) KN51-9001-R 8-1/2"(215mm) 15-1/4"(400mm) 10"(255mm) KN51-9002-R 6"(150mm) 12-3/4"(320mm) 9"(230mm) KN64 SERIES SINGLE PANTRY FAUCETS with SWIVEL GOOSENECK SPOUTS A B C KN64-9000 3-1/2"(90mm) 11-7/8"(300mm) 9-1/4"(235mm) KN64-9001 8-1/2"(215mm) 15-3/4"(400mm) 10"(255mm) KN64-9002 6"(150mm) 12-3/4"(320mm) 9"(230mm) with RIGID GOOSENECK SPOUTS KN64-9000-R 3-1/2"(90mm) 11-7/8"(300mm) 9-1/4"(235mm) B A C KN64-9001-R 8-1/2"(215mm) 15-1/4"(400mm) 10"(255mm) KN64-9002-R 6"(150mm) 12-3/4"(320mm) 9"(230mm) KN51 and KN64 SERIES SINGLE PANTRY FAUCETS with DOUBLE JOINTED SPOUTS FAUCET TYPE SPOUT LENGTH KN51-9018 DOUBLE 18"(450mm) KN64-9018 SINGLE 18"(450mm) NOTE: ALL FAUCETS ARE FURNISHED WITH 1/2" NPS MALE INLETS WITH 1/4" NPT UNION TAILPIECES AND MOUNTING HARDWARE. KN64 SERIES FAUCETS ARE AVAILABLE COMPLETE WITH MIXING VALVE. TO ORDER ADD SUFFIX...MV...TO 12" (300mm) 6" (150mm) FAUCETS FURNISHED WITH BOTH OPTIONAL AERATOR AND BUBBLER SCREEN. AVAILABLE WITH CERAMIC VALVES. Optional Accessories CHROME PLATED DESIGNER HANDLES K50-X117 (1-PAIR) Smooth, secure grip, may be used on any ProSeries Faucet or Pre-Rinse unit. CROSS HANDLE REPLACEMENT KIT K50-0111 (1-PAIR) Chrome plated cross handles are available for all ProSeries Faucets and Pre-Rinse Units. Kit includes two handles, hot and cold indicators and screws. WRIST BLADE HANDLES K50-0001(1-PAIR) Solid brass chrome plated, available for deck and wall mount faucets. Kit includes two blades, hot and cold buttons and screws. C21

Single Wall Mount Faucets KN70 SERIES SINGLE WALL MOUNT FAUCETS with SWING SPOUTS, SWIVEL and RIGID GOOSENECK SPOUTS and DOUBLE JOINTED SPOUTS SPOUT LENGTH 1/2" NPS FEMALE INLET WITH 1/2" NIPPLE AND M T G HARDWARE 2-5/8" (66mm) KN70 SERIES SINGLE WALL MOUNT FAUCETS with SWING SPOUTS SPOUT LENGTH KN70-9006 6"(150mm) KN70-9008 8"(200mm) KN70-9010 10"(250mm) KN70-9012 12"(300mm) KN70-9014 14"(350mm) KN70-9016 16"(400mm) KN70 SERIES SINGLE WALL MOUNT FAUCETS with SWIVEL GOOSENECK SPOUTS A B C B C A 2-5/8" (66mm) KN70-9000 3-1/2"(90mm) 9"(230mm) 6-1/4"(160mm) KN70-9001 8-1/2"(215mm) 12-1/2"(320mm) 7"(180mm) KN70-9002 6"(150mm) 10"(250mm) 6"(150mm) with RIGID GOOSENECK SPOUTS 1/2" NPS FEMALE INLET WITH 1/2" NIPPLE AND M T G HARDWARE KN70-9000-R 3-1/2"(90mm) 9"(230mm) 6-1/4"(160mm) KN70-9001-R 8-1/2"(215mm) 12-1/2"(320mm) 7"(180mm) KN70-9002-R 6"(150mm) 10"(250mm) 6"(150mm) 6" (150mm) 12" (300mm) 1/2" NPS FEMALE INLET WITH 1/2" NIPPLE AND M T G HARDWARE 2-5/8" (66mm) KN70 SERIES SINGLE WALL MOUNT FAUCET with DOUBLE JOINTED SPOUT KN70-9018 SPOUT LENGTH 18"(450mm) KN76 SERIES WOK RANGE FAUCETS with SWING SPOUTS SPOUT LENGTH FURNISHED WITH WRIST HANDLE 8-1/4" (209mm) 1/2"NPS MALE INLET WITH M T G HARDWARE KN76 SERIES WOK RANGE FAUCETS with SWING SPOUTS KN76-9010 KN76-9012 SPOUT LENGTH 10"(250mm) 12"(300mm) NOTE: OTHER SPOUT LENGTHS AVAILABLE ON REQUEST. FAUCETS FURNISHED WITH BOTH OPTIONAL AERATOR AND BUBBLER SCREEN AVAILABLE WITH CERAMIC VALVES C22

Elevated Spout Faucets KN52 and KN65 SERIES SINGLE and DOUBLE PANTRY FAUCETS with ELEVATED SWING SPOUTS SINGLE PANTRY FAUCET with ELEVATED SWING SPOUT 18"(450mm) RISER ELEVATES SPOUT 24"(600mm) ABOVE DECK AVAILABLE WITH TEMPERATURE MIXING VALVE... ORDER AS KN65-9012-MV 1/2" NPS MALE INLET, 12"(300mm) SPOUT LENGTH KN65-9012 FURNISHED WITH 1/4" NPT UNION TAILPIECE AND MOUNTING HARDWARE. NOTE: OTHER SPOUT LENGTHS AVAILABLE ON REQUEST. DOUBLE PANTRY FAUCET with ELEVATED SWING SPOUT 18"(450mm) RISER ELEVATES SPOUT 24"(600mm) ABOVE DECK 1/2" NPS MALE INLET, 12"(300mm) SPOUT LENGTH KN52-9012 FURNISHED WITH 1/4" NPT UNION TAILPIECE AND MOUNTING HARDWARE. NOTE: OTHER SPOUT LENGTHS AVAILABLE ON REQUEST. KN58 and KN62 SERIES DECK MOUNT FAUCETS with ELEVATED SWING SPOUTS DECK MOUNT FAUCET with ELEVATED SWING SPOUT 4"(100mm) ADJUSTABLE CENTRES 18"(450mm) RISER ELEVATES SPOUT 24"(600mm) ABOVE DECK 1/2" NPT FEMALE INLETS, 12"(300mm) SPOUT LENGTH KN58-4012 FURNISHED WITH 1/2" NPS NIPPLES AND MOUNTING HARDWARE. NOTE: OTHER SPOUT LENGTHS AVAILABLE ON REQUEST. DECK MOUNT FAUCET with ELEVATED SWING SPOUT 8"(200mm) ADJUSTABLE CENTRES 18"(450mm) RISER ELEVATES SPOUT 24"(600mm) ABOVE DECK 1/2" NPT FEMALE INLETS, 12"(300mm) SPOUT LENGTH KN62-8012 FURNISHED WITH 1/2" NPS NIPPLES AND MOUNTING HARDWARE. NOTE: OTHER SPOUT LENGTHS AVAILABLE ON REQUEST. FAUCETS FURNISHED WITH BOTH OPTIONAL AERATOR AND BUBBLER SCREEN AVAILABLE WITH CERAMIC VALVES Optional Accessories CHROME PLATED DESIGNER HANDLES K50-X117 (1-PAIR) Smooth, secure grip, may be used on any ProSeries Faucet or Pre-Rinse unit. CROSS HANDLE REPLACEMENT KIT K50-0111 (1-PAIR) Chrome plated Cross Handles are available for all ProSeries Faucets and Pre Rinse Units. Kit includes two handles, hot and cold indicators and screws. WRIST BLADE HANDLES 4 INCH, K50-0001 (1-PAIR) 6 INCH, K50-0001-6 Solid Brass Chrome Plated, available for Deck and Wall Mount Faucets. Kit includes Two Blades, Hot and Cold Buttons and Screws. C23

Pre-Rinse Hose Reel Assemblies OPEN HOSE REELS KHR-5635-O GRAY POWDER COATED KHR-5635-OSS STAINLESS STEEL PRE-RINSE HOSE REEL ASSEMBLIES Ideal for pre-rinsing, pot filling, misting produce and general cleaning Provides water quickly and conveniently to all kitchen areas Universal mounting allows for fast installation, can be either ceiling, floor or wall mounted Positive latching operation ensures hose will hold at desired length Heavy-duty special designed retrieval springs allow for easy hose recoil Available in stainless steel or durable gray powder coated finishes Furnished with ergonomically designed insulated spray valve handle control, which offers variable water velocity. Each valve handle furnished with non-marring high impact resistant bumper Heavy-duty hose tested to 210 F (99 C) and 250 psi (18 BAR) Furnished with stainless steel spring hose guard for extended hose life Full four year warranty Full 35 foot hose capacity Popular 3/8" inlet fittings E ENCLOSED HOSE REELS B C A D KHR-5635-E GRAY POWDER COATED 360 ROTATION KHR-5635-ESS STAINLESS STEEL OPTIONAL 360 SWIVEL HOSE FITTING KHR-600248 Installs between spray valve handle. Improves hose life and offers greater spray valve flexibility and versatility KHR-5635-O (OPEN) KHR-5635-OSS (OPEN-STAINLESS STEEL) KHR-5635-E (ENCLOSED) KHR-5635-ESS (ENCLOSED STAINLESS STEEL) REF. A 14-1/2" (368mm) 18-1/2"(470mm) B 13-3/4" (349mm) 15"(381mm) C 9-3/4" (243mm) 9-3/4" (243mm) D 2-1/2"(64mm) 2-1/2"(64mm) E 6"(152mm) 7"(178mm) OPTIONAL: 50' HOSE REEL AVAILABLE ON SPECIAL ORDER AND WITH SELECT-A-SPRAY ANGLE HEAD C24

Remote Mixing Valve & Misc. Valves 4" CONCEALED MIXING VALVE KN43-4050 NSF Listed New 1/4 Turn Full Volume Valves Built-in check valves prevent back-flow Ergonomic cross handles provided as standard Solid heavy-duty cast body and triple chrome plated finish 1/2" NPS male inlets on 4" centres 3/8" NPT female outlet International colour coded hot and cold identifiers provided Ideal for remote pot fillers, glass fillers, and hose reel assemblies 1" (25mm) 4" (102mm) 1/2" NPS MALE INLET 3/8" NPT 4" (102mm) 6-1/2" (165mm) 2" (50mm) ATMOSPHERIC VACUUM BREAKER ASSEMBLY SHUT-OFF CONTROL VALVE KHV-3850 In-line control valve Chrome plated finish 3/8" IPS inlet and outlet and 1/2" universal Designed for installation with hose reels ATMOSPHERIC VACUUM BREAKER K50-X137 3/8" NPT K50-X138 1/2" NPT K50-X138-S 1/2" NPT SATIN FINISH Series features full size orifice to assure pipe size capacity. Provides high water flow with minimal pressure loss. Suitable for temperatures up to 210 F(99 C). contains a durable silicone disc which has high heat and water hammer shock resistance and assures tight sealing with the lightest of seating contact. NOTE: Used in applications that are not subject to continuous pressure. FOR FLAT SURFACE MOUNTING ORDER KVB-6000 FOR 45 MOUNTING ORDER KVB-6045 Distance between pipes is 6" (152mm). KCV-0375 3/8" IPS Inlet and Outlet KCV-0500 1/2" IPS Inlet and Outlet KCV-0750 3/4" IPS Inlet and Outlet SOLID BRASS CHECK VALVES Solid brass for continuous pressure Designed for water use only ANTI-SIPHON, ANTI-SPILL VACUUM BREAKER with SHUT-OFF VALVES K50-X197 3/8" Female Inlet & Outlet K50-X198 Chrome plated Provides anti-siphon vacuum breaker for continuous pressure D A 1/2" Female Inlet & Outlet C B MODEL SIZE DIMENSIONS NO. A B C D K50-X197 3/8" 3-1/8" 4" 5-1/2" 2" (9.5mm) (79mm) (101mm) (140mm) (50mm) K50-X198 1/2" 3-3/8" 4-1/4" 5-3/4" 2" (12 mm) (86mm) (108mm) (146mm) (50mm) C25

Spout Bases KN72 and KN74 SERIES WALL and DECK MOUNT SPOUT BASES with SWING SPOUTS, SWIVEL and RIGID GOOSENECK SPOUTS and DOUBLE JOINTED SPOUTS SPOUT LENGTH SPOUT LENGTH KN72 and KN74 SERIES SPOUT BASES with SWING SPOUTS WALL MOUNT DECK MOUNT SPOUT LENGTH KN72-9006 KN74-9006 6"(150mm) KN72-9008 KN74-9008 8"(200mm) KN72-9010 KN74-9010 10"(250mm) KN72-9012 KN74-9012 12"(300mm) KN72-9014 KN74-9014 14"(350mm) KN72-9016 KN74-9016 16"(400mm) KN72-9018* KN74-9018* 18"(450mm) NOTE: WALL MOUNT MODELS ARE FURNISHED WITH 1/2" NPT FEMALE INLET, NIPPLE, ELL AND MOUNTING HARDWARE. DECK MOUNT MODELS ARE FURNISHED WITH 1/2" NPS MALE INLET WITH 1/4" NPT UNION TAILPIECE AND MOUNTING HARDWARE. * KN72-9018 AND KN74-9018 (NOT ILLUSTRATED) ARE DOUBLE JOINTED SPOUT MODELS. KN72 SERIES WALL MOUNT SPOUT BASES with SWIVEL GOOSENECK SPOUTS A B C KN72-9000 3-1/2"(90mm) 8"(200mm) 5-1/2"(140mm) 1-5/16" (33mm) A C B KN72-9001 8-1/2"(215mm) 12"(300mm) 6"(150mm) KN72-9002 6"(150mm) 9-1/4"(235mm) 5-1/4"(230mm) with RIGID GOOSENECK SPOUTS KN72-9000-R 3-1/2"(90mm) 8"(200mm) 5-1/2"(140mm) KN72-9001-R 8-1/2"(215mm) 12"(300mm) 6"(150mm) KN72-9002-R 6"(150mm) 9-1/4"(235mm) 5-1/4"(230mm) NOTE: WALL MOUNT SPOUT BASES ARE FURNISHED WITH 1/2" NPT FEMALE INLET, NIPPLE, ELL AND MOUNTING HARDWARE. KN74 SERIES DECK MOUNT SPOUT BASES with SWIVEL GOOSENECK SPOUTS A B C KN74-9000 3-1/2"(90mm) 8"(200mm) 5-1/2"(140mm) A B KN74-9001 8-1/2"(215mm) 12"(300mm) 6"(150mm) KN74-9002 6"(150mm) 9-1/4"(235mm) 5-1/4"(230mm) C with RIGID GOOSENECK SPOUTS KN74-9000-R 3-1/2"(90mm) 8"(200mm) 5-1/2"(140mm) KN74-9001-R 8-1/2"(215mm) 12"(300mm) 6"(150mm) KN74-9002-R 6"(150mm) 9-1/4"(235mm) 5-1/4"(230mm) NOTE: DECK MOUNT SPOUT BASES ARE FURNISHED WITH 1/2" NPS MALE INLET WITH 1/4" NPT UNION TAILPIECE AND MOUNTING HARDWARE. FAUCETS FURNISHED WITH BOTH OPTIONAL AERATOR AND BUBBLER SCREEN. FOR A COMPLETE LINE OF OPTIONAL ACCESSORIES SEE PAGES C14 AND C15 C26

Specification Grade Hand Sink Faucets KN41 SERIES KN41 and KN45 SERIES 4" WALL and DECK MOUNT FAUCETS with SWING SPOUTS, SWIVEL AND RIGID GOOSENECK SPOUTS NSF LISTED NEW EASY 1/4 TURN FULL OPEN FEATURE EXCEEDS A.D.A. REGULATIONS WITH HANDLES MOUNTED IN CORRECT ORIENTATION THE ONLY 4" FAUCET WITH BUILT-IN CHECK VALVES TO PREVENT BACK FLOW AND OFFER POSITIVE SEAL HIGH COMMERCIAL QUALITY FOR HAND SINKS INTERNATIONAL COLOUR CODED HOT AND COLD IDENTIFIERS PROVIDED OPTIONAL WRIST BLADES AVAILABLE SOLID HEAVY- DUTY CAST BODIES A C B A C B 2"(50mm) KN45 SERIES 2"(50mm) KN41-4000 KN41-4002 KN41-4001 KN41 SERIES DECK MOUNT FAUCETS with 4"(100mm) CENTRES with SWIVEL GOOSENECK SPOUTS A B C 3-9/16"(90mm) 8-9/16"(217mm) 6"(152mm) 6-5/16"(160mm) 9-5/8"(244mm) 5-9/16"(141mm) 9"(229mm) 12-9/16"(319mm) 6-5/16"(160mm) KN41-4006 KN41-4008 KN41-4010 KN41-4012 with SWING SPOUTS 6"(152mm) 4-3/8"(111mm) 2-5/8"(66mm) 8"(203mm) 5-5/16"(135mm) 3-1/16"(78mm) 10"(254mm) 5-13/16"(148mm) 3-9/16"(90mm) 12"(304mm) 6-1/4"(159mm) 4"(101mm) *SHOWN WITH OPTIONAL WRIST BLADE HANDLES (NO. K50-0001) 1"(25mm) A 1"(25mm) C B 1"(25mm) 1"(25mm) A C B KN45 SERIES BACKSPLASH FAUCET with 4"(100mm) CENTRES with SWIVEL GOOSENECK SPOUTS A B C KN45-4000 3-9/16"(90mm) 8-7/16"(214mm) 5-7/8"(149mm) KN45-4002 6-5/16"(160mm) 9-1/2"(241mm) 5-3/8"(136mm) KN45-4001 9"(229mm) 12-9/16"(319mm) 6-3/16"(157mm) with SWING SPOUTS KN45-4006 6"(152mm) 4-3/4"(121mm) 2-1/2"(63mm) KN45-4008 8"(203mm) 5-3/16"(132mm) 3"(76mm) KN45-4010 10"(254mm) 5-11/16"(144mm) 3-7/16"(87mm) KN45-4012 12"(305mm) 6-1/8"(155mm) 3-7/8"(98mm) ALL KN41 AND KN45 SERIES FAUCETS HAVE1/2 NPSM MALE INLETS AND ARE FURNISHED WITH MOUNTING HARDWARE. FOR REPLACEMENT PARTS OR VALVE ASSEMBLIES SEE PAGE C14, C15. C27

Deck Mount Faucets KN41 and KN45 SERIES 8" WALL and DECK MOUNT FAUCETS with SWING SPOUTS, SWIVEL and RIGID GOOSENECK SPOUTS KN41 SERIES NSF LISTED 8" (200mm) CENTRE NEW EASY 1/4 TURN FULL OPEN FEATURE EXCEEDS A.D.A REGULATIONS THE ONLY 8" FAUCET WITH BUILT-IN CHECK VALVES TO PREVENT BACK AND CROSS FLOW AND OFFER POSITIVE SEAL SPECIFICATION GRADE QUALITY FOR HAND SINKS COLOUR CODED INDEXES MEET INTERNATIONAL STANDARDS OPTIONAL WRIST BLADES AVAILABLE SOLID HEAVY-DUTY CAST BODIES A B C A C B 2"(50mm) 2"(50mm) KN41 SERIES DECK MOUNT FAUCETS with 8"(200mm) CENTRES with SWIVEL GOOSENECK SPOUTS KN41-8000 A 3-1/2"(90mm) B 8-7/16"(214mm) C 5-7/8"(149mm) KN45 SERIES KN41-8001 8-1/2"(215mm) 12-7/16"(316mm) 6-3/16"(157mm) KN41-8002 6"(150mm) 9-1/2"(241mm) 5-3/8"(136mm) with SWING SPOUTS KN41-8006 6"(150mm) 4-7/8"(124mm) 2-5/8"(67mm) KN41-8008 8"(200mm) 8"(136mm) 3-1/8"(79mm) KN41-8010 10"(250mm) 5-13/16"(148mm) 3-9/16"(90mm) KN41-8012 12"(300mm) 6-1/4"(159mm) 4"(102mm) KN45 SERIES WALL MOUNT FAUCETS WITH 8"(200mm) CENTRES with SWIVEL GOOSENECK SPOUTS A B C KN45-8000 3-1/2"(90mm) 8-7/16"(214mm) 5-7/8"(149mm) 1"(25mm) KN45-8001 8-1/2"(215mm) 12-7/16"(316mm) 6-3/16"(157mm) KN45-8002 6"(150mm) 9-1/2"(241mm) 5-3/8"(136mm) 1"(25mm) with SWING SPOUTS KN45-8006 6"(150mm) 2-1/2"(63mm) 4-3/4"(121mm) KN45-8008 8"(200mm) 5-1/4"(132mm) 3"(76mm) A B C A C B KN45-8010 10"(250mm) 5-11/16"(144mm) 3-7/16"(87mm) KN45-8012 12"(300mm) 6-1/8"(155mm) 3-7/8"(98mm) 1"(25mm) 1"(25mm) ALL KN41 AND KN45 SERIES FAUCETS HAVE1/2 NPSM MALE INLETS AND ARE FURNISHED WITH MOUNTING HARDWARE. FOR REPLACEMENT PARTS OR VALVE ASSEMBLIES SEE PAGE C14, C15. C28

featuring Institutional Faucet Line KN83 SERIES 4" DECK MOUNT FAUCET WITH CAST SPOUT KN83-4104-CE4 4" Cast Spout Aerator 2.2 GPM max (KN50-X120) 1-1/2" (38mm) clearance deck to aerator 4" SANIGUARD treated wrist handles (K50-0001) 1/4 Turn ceramic valves 1/2 in. NPSM inlets with couplings KN83 SERIES 4" DECK MOUNT FAUCET WITH RIGID GOOSENECK SPOUT KN83-4100-RE4 4" (102mm) centreline to centre of outlet Gooseneck spout (KN11-X100) 6" (152mm) clearance deck to aerator 4" SANIGUARD treated wrist handles (K50-0001) 1/4 Turn ceramic valves Aerator 2.2 GPM max (KN50-X120) 1/2 in. NPSM inlets with couplings ADA Compliant Complies with: ANSI / ASME A112.18.1M CSA B125 ANSI / NSF STD. 61 ADA Compliant Complies with: ANSI / ASME A112.18.1M CSA B125 ANSI / NSF STD. 61 OPTIONAL HANDLES: K50-0110 Standard Encore lever handles K50-0001 4" Wrist handles K50-0001-6 6" Wrist handles K50-0111 Cross handles K50-X117 Chrome plated designer (plastic) handles OPTIONAL SPOUTS: KN11-X006 6" Straight spout KN11-X008 8" Straight spout KN11-X010 10" Straight spout KN11-X012 12" Straight spout KN11-X014 14" Straight spout KN11-X016 16" Straight spout KN11-X000 3 1/2" Gooseneck spout KN11-X001 8 1/2" Gooseneck spout KN11-X002 6" Gooseneck spout KN11-X100 3 1/2" Rigid gooseneck spout KN11-X101 8 1/2" Rigid gooseneck spout KN11-X102 6" Rigid gooseneck spout OPTIONAL AERATORS: KN50-X201-KKey for vandal resistant aerators Aerators for the Encore KN11 series spout KN50-X120 2.2 GPM max - Aerated stream KN50-X120-A 0.5 GPM PC - Spray KN50-X120-F 1.5 GPM max - Laminar, antimicrobial KN50-X120-S 6.0 GPM max - Wide Rose Spray KN50-X201 2.2 GPM max - Aerated stream, vandal resistant KN50-X201-A 0.5 GPM PC - Spray, vandal resistant KN50-X201-H 2.2 GPM max - Aerated stream, vandal & hose resistant KN50-X201-F 1.5 GPM max - Laminar, antimicrobial, vandal resistant Aerators for Cast Spouts KN50-X121 2.2 GPM max - Aerated Stream KN50-X121-A 0.5 GPM PC - Spray KN50-X121-F 1.5 GPM max - Laminar, antimicrobial KN50-X203-A 0.5GPM PC - Spray, vandal resistant KN50-X203-F 1.5 GPM max - Laminar, antimicrobial & vandal resistant C29

Institutional Faucet Line featuring KN84 SERIES CONCEALED DECK MOUNT WIDESPREAD FAUCET WITH GOOSENECK SPOUT KN84-8102-RS4 6" Rigid gooseneck spout Rose Spray aerator (KN50-X120-S) 4" SANIGUARD treated wrist handles (K50-0001) 1/4 Turn ceramic valves 5" - 24" adjustable centres Supplied with stainless steel braided hoses Vandal resistant Anti-rotation feature Refer to KN83 Series List of Options for: Aerators Spouts ADA Compliant Complies with: ANSI / ASME A112.18.1M CSA B125 ANSI / NSF STD. 61 KN84 SERIES CONCEALED DECK MOUNT WIDESPREAD FAUCET WITH CAST SPOUT KN84-8105-CE4 Cast Spout Assembly 2" (51 mm) clearance from deck to aerator 1/2" NPSM coupling nuts on inlets 4" SANIGUARD treated wrist handles (K50-0001) 1/4 Turn ceramic valves 2.2 GPM aerator (KN50-X121) 5" - 24" adjustable centres Supplied with stainless steel braided hoses Vandal resistant Anti-rotation feature Refer to KN83 Series List of Options for: Aerators Handles ADA Compliant Complies with: ANSI / ASME A112.18.1M CSA B125 ANSI / NSF STD. 61 KN84 SERIES CONCEALED DECK MOUNT WIDESPREAD FAUCET WITH SELF-CLOSING METERED VALVES KN84-8201-RS 8 1/2" Rigid gooseneck spout Rose Spray aerator (KN50-X120-S) Concealed body 1/2" NPSM coupling nuts on inlets Self-closing metering valves - adjustable timed flow 5" - 24" adjustable centres Supplied with stainless steel braided hoses Vandal resistant Refer to KN83 Series List of Options for: Handles ADA Compliant adjustable timed flow Complies with: ANSI / ASME A112.18.1M CSA B125 ANSI / NSF STD. 61 C30

featuring Soap Dispenser and Grab Bars GRAB BARS Stainless steel, 1-1/2" diameter grab bars. Available in smooth or knurled finish, complete with concealed mounting flange and press-on flange cover. All grab bars are permanently treated with SANIGUARD. DIMENSION SMOOTH KNURLED 12" GRAB BAR GBS15-1112-Q GBS15-4112-Q 16" GRAB BAR GBS15-1116-Q GBS15-4116-Q 18" GRAB BAR GBS15-1118-Q GBS15-4118-Q 24" GRAB BAR GBS15-1124-Q GBS15-4124-Q 30" GRAB BAR GBS15-1130-Q GBS15-4130-Q 32" GRAB BAR GBS15-1132-Q GBS15-4132-Q 36" GRAB BAR GBS15-1136-Q GBS15-4136-Q 42" GRAB BAR GBS15-1142-Q GBS15-4142-Q 48" GRAB BAR GBS15-1148-Q GBS15-4148-Q 30"x30" GRAB BAR GBS15-113030Q GBS15-413030Q 40"x30" GRAB BAR GBS15-414030Q Wall mount electronic soap dispenser uses standard liquid soap. Battery operated with infrared sensor. Requires 6 AA or one 9V battery. Part Number KS20-9310 Deck mount manual soap dispenser with SANIGUARD. Uses standard liquid soap, refills from top. Part Number KS10-1000 C31

Service Sink Faucets SHOWN WITH RECOMMENDED VACUUM BREAKER K77 SERIES SERVICE SINK FAUCETS Heavy Cast Spout with Pail Hook and Hose Thread and Optional Vacuum Breaker K77 SERIES FAUCETS with SUPPORT BRACKET 8"(200mm) ADJUSTABLE CENTRES UNIQUE BRACKET PERMITS SPOUT TO BE SUPPORTED FROM ABOVE OR BELOW BRACKET ADJUSTS UP TO 2"(50mm) BEHIND INLETS VACUUM BREAKER PROVIDES ADDITIONAL PROTECTION AGAINST BACKFLOW (K77-8106-BR ONLY) FURNISHED WITH STANDARD 3/4" GARDEN HOSE THREAD 2-5/8" (66mm) SPOUT LENGTH K77 SERIES SERVICE SINK FAUCETS with SUPPORT BRACKET K77-8006-BR SPOUT LENGTH 6-1/2" (162mm) VACUUM BREAKER NO 1/2" NPT FEMALE INLETS K77-8106-BR 6-1/2" (162mm) YES NOTE: BODY CASTING PROVIDED WITH A ROUGH CHROME FINISH. AVAILABLE WITH CERAMIC VALVES. 2-5/8" (66mm) K77 SERIES FAUCETS without SUPPORT BRACKET 8"(200mm) ADJUSTABLE CENTRES VACUUM BREAKER PROVIDES ADDITIONAL PROTECTION AGAINST BACKFLOW (K77-8102 ONLY) FURNISHED WITH STANDARD 3/4" GARDEN HOSE THREAD SPOUT LENGTH 1/2" NPT FEMALE INLETS K77 SERIES SERVICE SINK FAUCETS without SUPPORT BRACKET SPOUT LENGTH K77-8002 2-1/2" (62mm) K77-8102 2-1/2" (62mm) VACUUM BREAKER NO YES NOTE: BODY CASTING PROVIDED WITH A ROUGH CHROME FINISH. AVAILABLE WITH CERAMIC VALVES. 1 5/16 (33mm) 3 (76mm) 9 3/16 (233mm) 8 5/16 (381mm) 3 1/2 (89mm) 1/2"NPSM(F) INLETS K78 SERIES SERVICE SINK FAUCET Model No. K78-8106-BR 8" Adjustable Centres 9 3/16" (233mm) Clearance from wall to centre of outlet 3" (76mm) Clearance from wall to centre of valve Rough chrome finish Built in stops Vacuum breaker spout with 3/4" garden hose thread and pail hook Top support wall bracket C32

Faucet Accessories ROSE SPRAY SPOUT TIP TAMPER RESISTANT AERATOR/BLEEDER AERATOR KN50-X120 GARDEN HOSE BIBB KN50-X120-S KN50-X201-H K50-X234 *optional All metal, chrome plated. Vandal resistant aerator/bleeder with 3/8" NPT male inlet. Use on exposed bleeder line. After attaching unit spins freely. *OPTIONAL INSTALLATION KEY AVAILABLE AS #KN50-X201-K Non-splash aerator supplied on all Encore and Top-Line faucets. Available as an accessory for other faucets. 3/8" NPT x 3/4" garden hose adapter. Chrome plated brass. SPOUT ADAPTER KN50-X148 TAMPER PROOF AERATOR KN50-X201 SWING TO RIGID ADAPTER KN50-X122 TOP OF RISER (RIGID) TO SWING ADAPTER KN50-X076 *optional T & S Spout adapter adapts ENCORE spout to T & S faucet body Tamper proof non-splash aerator. Installation key included. Available as an accessory on all faucets. *OPTIONAL INSTALLATION KEY AVAILABLE AS #KN50-X201-K To accommodate field conversion of faucets with standard Encore and Top-Line swivel spout outlets to accept 3/8" NPT male riser pipe or rigid gooseneck spouts. Used in combination with a riser pipe to accommodate a swing spout or swivel gooseneck spout application. Has 3/8" NPT female inlet. RIGID TO SWING ADAPTER KN50-X075 IN-LINE VACUUM BREAKER FOR RISER PIPE APPLICATION K50-X139 Provided with 3/8" NPS male inlet and 3/8" NPS female outlet. CONTINUOUS PRESSURE IN-LINE VACUUM BREAKER FOR HOSE APPLICATION K50-X196 HOSE CONNECTION VACUUM BREAKER K50-X136 K50-X139-B Provided with 3/8" NPS female inlet and 3/8" NPS male outlet. To accommodate field conversion of faucets with 3/8" NPT female outlets to accept swing spouts or swivel gooseneck spouts. A back siphonage preventer for units where Pre-Rinse or Spray Hoses may be attached. Prevents the back flow of contaminated water into the safe drinking water supply. Note: Used in applications that are not subject to continuous pressure. A back siphonage preventer for units where Pre-Rinse or Spray Hoses may be attached. Prevents the backflow of contaminated water into the safe drinking water supply. Provided with 3/8" NPT inlet and outlet. NOTE: Used in applications that are subject to continuous pressure. For hose thread faucets where Pre-Rinse or Spray Hoses may be attached. To prevent back flow of contaminated water into the safe drinking water supply. Note: Used in applications that are not subject to continuous pressure. HOSE ADAPTERS KN50-X127 Converts standard Pre-Rinse hose connection to male 1/4" NPT. Converts Encore hose to fit Fisher Pre-Rinse. MODEL KN50-X128 Converts standard Pre-Rinse hose connection to male 3/8" NPT. Converts Encore hose to fit Chicago Pre-Rinse. KN50-X129 Converts standard Pre-Rinse hose connection to male 1/2" NPT. TEMPERATURE MIXING VALVE KN63-Y005 Valve contains built-in adjustable flow controls that allow faucet water temperature to be preset. Also incorporates built-in ball checks to prevent back flow and may be installed on any Encore single inlet faucet or pre-rinse. Provided with 1/4" NPT female outlet and 1/2" NPS male inlets on 4"(100mm) centres. Furnished with 1/4" union tailpieces. FEMALE HOSE SPOUT ADAPTER K11-X080 Attaches garden hose vacuum breaker to spout adapter. For Use with K50-X136. 55/64-27 x 3/4". C33

Replacement Spouts & Spout Bases WALL MOUNTED SPOUT BASES FAUCET CONTROL 4"(100mm) and 6"(152mm) SPOUTS HIGHLY POLISHED CHROME PLATED BRASS IDEAL FOR HAND SINK APPLICATION PATENT NO. 6994318 ADA COMPLIANT A 1/2" NPS D QUIK-WASH HAND WASH FAUCET CONTROL KN91-0100 B C KN80 SERIES WALL MOUNTED SPOUT BASES A B C D K80-9004 1-1/2"(38mm) 1-5/16"(34mm) 4"(102mm) 2-1/8"(54mm) K80-9006 1-1/2"(38mm) 1-5/16"(34mm) 6"(152mm) 2-1/8"(54mm) Make your hand sink faucet sanitary and hands-free, patented mechanical control offers both automatic self-closing and a hands-free full-on position, allowing for multipurpose use. Supplied with universal adapters and rugged solid brass and stainless steel construction throughout. Available with our exclusive SANIGUARD Antimicrobial Treatment which retards the growth of bacteria, mold and fungus, and with proper care and handling can last the life of the product. FAUCET REPLACEMENT SPOUTS FOR USE WITH ALL ENCORE AND TOP-LINE FAUCETS HIGHLY POLISHED CHROME PLATED BRASS STRAIGHT REPLACEMENT SPOUT KN11-X006 KN11-X008 KN11-X010 KN11-X012 KN11-X014 KN11-X016 SPOUT LENGTH 6" (150mm) 8" (200mm) 10" (250mm) 12" (300mm) 14" (350mm) 16" (400mm) DOUBLE JOINTED SPOUT EXTENSION KN11-X106 KN11-X112 6"(150mm) Spout length 12"(300mm) Spout length FOR USE WITH STRAIGHT SPOUTS LISTED ABOVE-SEE PG. C15 GOOSENECK REPLACEMENT SPOUT SPOUT LENGTH KN11-X000 3-1/2" (90mm) KN11-X001 8-1/2" (215mm) KN11-X002 6" (150mm) SPOUT EXTENSION FOR DOUBLE JOINTED APPLICATION...SEE PAGE C15. RIGID GOOSENECK REPLACEMENT SPOUT 3/8" NPT MALE INLET SPOUT LENGTH KN11-X100 3-1/2" (90mm) KN11-X101 8-1/2" (215mm) KN11-X102 6" (150mm) C34

Fabricated Stainless Steel Sink Bowls STAINLESS STEEL FABRICATED SINK BOWLS NSF LISTED HEAVY-DUTY 14 GA. AND 16 GA. CONSTRUCTION FULLY FORMED, FOLDED AND WELDED CONSTRUCTION FULLY POLISHED INSIDE AND OUT, READY FOR INSTALLATION FURNISHED WITH TRIMMED EDGES FOR EASY WELDING INSTALLATION CROSS EMBOSSED BASIN PROVIDES POSITIVE DRAINAGE 3-1/2" DIA. DRAIN HOLE PROVIDED TYPE 304 STAINLESS STEEL THROUGHOUT COMPLETE INVENTORY OF CONVENTIONAL SIZES NSF-2 STAINLESS STEEL FABRICATED SINK BOWLS BOWL SIZE GAUGE L x W x D CUT-OUT SIZE REQ D L x W 18" x 24" x 12" FB16-182412 (457 x 610 x 305mm) 16 18-3/16" x 24-3/16" (462 x 614mm) LENGTH DEPTH WIDTH 3-1/2" DIA. DRAINAGE HOLE FB16-242412 FB16-121410 FB16-162012 FB16-181812 FB16-202012 FB16-202008 24" x 24" x 12" (610 x 610 x 305mm) 12" x 14" x 10" (305 x 356 x 254mm) 16" x 20" x 12" (406 x 508 x 305mm) 18" x 18" x 12" (457 x 457 x 305mm) 20" x 20" x 12" (508 x 508 x 305mm) 20" x 20" x 8" (508 x 508 x 203mm) 16 16 16 16 16 16 FB14-162014 FB14-181814 FB14-182414 FB14-242414 FB14-202014 FB14-202008 16" x 20" x 14" (406 x 508 x 356mm) 18" x 18" x 14" (457 x 457 x 356mm) 18" x 24" x 14" (457 x 610 x 356mm) 24" x 24" x 14" (610 x 610 x 356mm) 20" x 20" x 14" (508 x 508 x 356mm) 20" x 20" x 8" (508 x 508 x 203mm) 14 14 14 14 14 14 24-3/16" x 24-3/16" (614 x 614mm) 12-3/16" x 14-3/16" (310 x 360mm) 16-3/16" x 20-3/16" (411 x 513mm) 18-3/16" x 18-3/16" (462x 462mm) 20-3/16" x 20-3/16" (513 x 513mm) 20-3/16" x 20-3/16" (513 x 513mm) 16-3/16" x 20-3/16" (411 x 513mm) 18-3/16" x 18-3/16" (462 x 462mm) 18-3/16" x 24-3/16" (462 x 614mm) 24-3/16" x 24-3/16" (614 x 614mm) 20-3/16" x 20-3/16" (513 x 513mm) 20-3/16" x 20-3/16" (513 x 513mm) C35

Deep Drawn Sink Bowls DEEP DRAWN STAINLESS STEEL SINK BOWLS POT SINKS BAR SINKS DISH SINKS PREP SINKS UTILITY SINKS MOP SINKS SELF-RIM SINKS PRE-RINSE SINKS SOAK SINKS SERVICE SINKS SCULLERY SINKS STAINLESS STEEL SINK BOWLS (STANDARD TYPE) BOWL SIZE (A x B x C) TRIM SIZE (D x E) GAUGE 1416A-12 1620A-08 1620A-10 1620A-12 1620A-14A 2020A-10 2020A-12 2020A-14A 2424A-14A 14" x 16" x 12"dp. 16-1/2" x 18-1/2" 18 (355mm x 406mm x 304mm) (419mm x 469mm) (1.2mm) 16" x 20" x 8"dp. 18-1/2" x 22-1/2" 18 (406mm x 508mm x 200mm) (469mm x 571mm) (1.2mm) 16" x 20" x 10"dp. 18-1/2" x 22-1/2" 18 (406mm x 508mm x 254mm) (469mm x 571mm) (1.2mm) 16" x 20" x 12"dp. 18-1/2" x 22-1/2" 18 (406mm x 508mm x 304mm) (469mm x 571mm) (1.2mm) 16" x 20" x 14"dp. 18-1/2" x 22-1/2" 14 (406mm x 508mm x 355mm) (469mm x 571mm) (1.9mm) 20" x 20" x 10"dp. 22-1/2" x 22-1/2" 18 (508mm x 508mm x 254mm) (571mm x 571mm) (1.2mm) 20" x 20" x 12"dp. 22-1/2" x 22-1/2" 18 (508mm x 508mm x 304mm) (571mm x 571mm) (1.2mm) 20" x 20" x 14"dp. 22-1/2" x 22-1/2" 14 (508mm x 508mm x 355mm) (571mm x 571mm) (1.9mm) 24" x 24" x 14"dp. 26-1/2" x 26-1/2" 14 (609mm x 609mm x 355mm) (673mm x 673mm) (1.9mm) STAINLESS STEEL SINK BOWLS (SELF RIMMING...DROP-IN TYPE) BOWL SIZE TRIM SIZE GAUGE 10" x 14" x 5" dp. 13" x 19" 20 1014B-05 (254mm x 355mm x 127mm) (304mm x 457mm) (.9mm) 10" x 14" x 10" dp. 13" x 19" 18 1014B-10B (254mm x 355mm x 254mm) (304mm x 457mm) (1.2mm) NOTE: SINK BOWLS ACCEPT STANDARD 3-1/2" LEVER/TWIST AND BASKET DRAINS 1-1/8"(28mm) DIA. HOLES FOR FAUCET 19"(457mm) 14"(355mm) 4" 4 1/2" (100mm) (100mm) 2"(50mm) RADIUS 10"(254mm) 13"(300mm) 2" (41mm) 10-24 x 1-1/2"(38mm) LG. FASTENER STUDS WITH MOUNTING CLIPS 3 1/2" (76mm) 10 1/2"(254mm) DRAIN OPENING (SEE NOTE) 1 1/2" (25mm) 1/2"(12mm) RADIUS TYP. CUT-OUT SIZE 11" X 17" (279mm x 431mm) WITH 1-1/4"(32mm) RADIUS CORNERS NOTE: SINK BOWLS ACCEPT STANDARD 3-1/2" LEVER/TWIST AND BASKET DRAINS SEE PAGES C37, C40, C41 E B 3"(76mm) RADIUS TYP. A D C DRAIN OPENING (SEE NOTE ABOVE) 3" (76mm) RADIUS TYP. 1-1/4" (32mm) 1-1/4" (32mm) 1/2"(12mm) RADIUS TYP. NOTE: ALL SINK BOWLS ARE TYPE 304 STAINLESS STEEL POLISHED TO A #4 FINISH STAINLESS STEEL SINK BOWLS (BAR TYPE) BOWL SIZE TRIM SIZE GAUGE 1014A-10 1014A-10A 10" x 14" x 10" dp. 10" x 14" x 10" dp. 13" x 19" 13" x 19" 20 18 (254mm x 355mm x 254mm) (254mm x 355mm x 254mm) (304mm x 457mm) (304mm x 457mm) (.9mm) (1.2mm) NOTE: SINK BOWLS ACCEPT STANDARD 1-1/2" SINK DRAINS 1 1/2"(50mm) 19"(457mm) 14"(355mm) 2"(50mm) RADIUS 10"(254mm) 13"(304mm) 4-3/4"(120mm) DRAIN OPENING (SEE NOTE) 1 1/2" (50mm) 2"(50mm) RADIUS TYP. 1/2"(12mm) RADIUS TYP. 6 1/2"(171mm) C36

Fabricated Stainless Steel Pre-Rinse Sink Assembly FABRICATED STAINLESS STEEL PRE-RINSE SINK ASSEMBLY NSF LISTED HEAVY-DUTY 14 GA. FULLY FORMED, FOLDED AND WELDED CONSTRUCTION FULLY POLISHED INSIDE AND OUT; READY FOR INSTALLATION FURNISHED WITH TRIMMED EDGES FOR EASY WELDING INSTALLATION CROSS EMBOSSED BASIN PROVIDES POSITIVE DRAINAGE 3-1/2" DIA. DRAIN HOLE PROVIDED TYPE 304 STAINLESS STEEL THROUGHOUT COMPLETE WITH PERFORATED SCRAP BASKET WITH 1" O.D. TUBULAR TRAY GLIDES 20" (508mm) 20" (508mm) FB80-2020 3-1/2"(89mm) DIA. HOLE 6" (152mm) 6" (152mm) EXTRUDED FEET (4) BOWL SIZE GAUGE CUT-OUT SIZE REQ D L x W x D L x W NSF-2 FB80-2020* 20" x 20" x 6" 14 20-3/16" x 20-3/16" (508 x 508 x 152mm) (513 x 513mm) * 3-1/2" DIA. CENTRE DRAINAGE HOLE PROVIDED C37

Pre-Rinse Sink Assembly STAINLESS STEEL PRE-RINSE SINK ASSEMBLY E80-2020 featuring... DEEP DRAWN BASKET and SINK SLIDE BAR and BASKET INTEGRALLY WELDED SIZED FOR STANDARD 20" x 20" (508mm x 508mm) DISH RACK ALL STAINLESS STEEL COMPONENTS (TYPE 304) DIMENSIONS 2-1/4" (57mm) 21-1/2" (546mm) 21-1/2" (546mm) 11-1/2" (292mm) SPECIFICATIONS BAR: 1" x 3/16" (25.4mm x 4.7mm) STAINLESS STEEL, TYPE 304 BASKET: 20 GA. STAINLESS STEEL, TYPE 304 WITH A #4 FINISH SINK: 18 GA. STAINLESS STEEL, TYPE 304 WITH A #4 FINISH CONSTRUCTION: BASKET AND SINK ARE DEEP DRAWN BASKET AND SLIDE BAR ARE INTEGRALLY WELDED INSTALLATION: STEP 1. CUT 21-3/4" x 21-3/4"(552mm x 552mm) OPENING STEP 2. WELD TO DISHTOP TABLE WELD EDGE TO UNDERSIDE 21-3/4" (552mm) 21-3/4" (552mm) UNDERSIDE OF DISHTABLE SINK BAR BASKET 8-1/2" (212mm) SINK PROVIDED WITH A 3-1/2"(90mm) DIA. DRAIN OPENING DRAIN HOLE CONFIGURATION 1"(25mm) 5/8"(16mm) BASKET IS PROVIDED WITH HOLE SPACING PATTERN AS ILLUSTRATED. ALL HOLES ARE 1/4"(6.5mm) DIAMETER NOTE: HEAVY DUTY STAINLESS STEEL BASKET CAN BE ORDERED SEPARATELY...SPECIFY E80-X015 TO ORDER HEAVY DUTY STAINLESS STEEL SINK ONLY...SPECIFY E80-X010 C38

Abs Plastic Rotary Drain SINK MATE TM ABS PLASTIC ROTARY DRAIN NSF LISTED CSA AND ANSI CERTIFIED ECONOMICAL SOLID ABS PLASTIC EXPOSED AREAS STAINLESS STEEL CLAD CHROME PLATED, TWIST LOCK, REMOVABLE BEEHIVE CRUMB-CUP PREVENTS CLOGGING AND INSURES CONTINUOUS WATER FLOW CHEMICAL RESISTANT CELCON SEALS ELIMINATE COSTLY REPLACEMENT OF O-RINGS AND CONVENTIONAL GASKETS REMOTE OPERATION SAFELY PERMITS SINK TO DRAIN WHILE PROTECTING OPERATORS HANDS FROM HARMFUL BROKEN GLASS, SHARP KNIVES AND UTENSILS...REPLACES CONVENTIONAL BASKET DRAINS COMPONENT CERTIFIED TO ANSI/ASME 112.18.1M MATERIALS CONFORM TO FDA CFR 21 FITS STANDARD 3-1/2"(90mm) SINK OPENING UNIVERSAL BODY PROVIDES BOTH 2" and 1-1/2" (50 and 38mm) WASTE OUTLET CONNECTIONS AND CAN INSTANTLY CONVERT TO ACCEPT AN OVERFLOW ASSEMBLY ELIMINATING DOUBLE INVENTORIES FULL OPENING BALL VALVE ALLOWS ACCESS FOR SNAKING OR PLUNGING FROM SINK TOP... ELIMINATING COSTLY SERVICE CALLS UNAFFECTED BY TODAY'S HARSH CLEANING CHEMICALS PERFECT FOR HAND SINK APPLICATIONS UNIQUE BODY STYLE PROVIDES FAST INSTALLATION FROM SINK TOP PATENT PENDING 2-3/4" (70mm) 4-1/8" (105mm) DPL-8000 FURNISHED WITH 12"(300mm) HANDLE 5/8"(15mm) ID OVERFLOW HOSE FITTING HEAD GASKET SLIP WASHER FLANGE NUT HANDLE ASS Y 2" NPSM OUTLET 1-1/2" PIPE SOCKET 12"(300mm) 2" (50mm) OPTIONAL OVERFLOW ASSEMBLY E52-1000 OVERFLOW ASSEMBLY CONSISTS OF: 1-5/8"(41mm) NICKEL PLATED BRASS BRANCH TAILPIECE 1-1/8" (28mm) SUB- ASSEMBLY, (2) STAINLESS STEEL CLAMPS, 32" (815mm) LONG RUBBER HOSE AND CHROME PLATED ABS OVERFLOW HEAD. OPTIONAL REDUCER DPL-Y006 3/8"(10mm) 1-1/4" (32mm) 1/2" NPSM 2-9/16" DIA. (65mm) 2 NPSM RUBBER WASHER 5/8" (16mm) DPL-8000-S FURNISHED WITH 6"(152.4mm) HANDLE 4-1/8" (105mm) 2-3/4" (70mm) 5/8"(15mm) OVERFLOW HOSE FITTING HEAD GASKET SLIP WASHER FLANGE NUT HANDLE ASS Y 2" NPSM OUTLET 1-1/2" PIPE SOCKET 6"(152mm) C39

Stainless Steel Rotary Drain DSS-8000-P PATENTED DRAIN TM MASTER DSS-Y007 OPTIONAL FLAT STRAINER SOLID STAINLESS STEEL - TYPE 316 SOLID STAINLESS STEEL TYPE 316 THROUGHOUT NSF LISTED CSA AND ANSI CERTIFIED PATENTED ROTARY VALVE PROVIDES FAST, UNOBSTRUCTED WATER EVACUATION TWIST LOCK RECESSED REMOVABLE BEEHIVE CRUMB-CUP PREVENTS CLOGGING AND INSURES CONTINUOUS WATER FLOW SELF-ADJUSTING HEAT AND CHEMICAL RESISTANT TEFLON SEALS ELIMINATE COSTLY REPLACEMENT OF O-RINGS AND CONVENTIONAL GASKETS 3 TIMES THE FLOW RATE OF CONVENTIONAL LEVER DRAINS PATENTED COMPONENT CERTIFIED TO ANSI/ASME A112.18.1M FULL OPENING BALL VALVE ALLOWS ACCESS FOR SNAKING OR PLUNGING FROM SINK TOP... ELIMINATING COSTLY SERVICE CALLS UNIQUE BODY STYLE PROVIDES FAST INSTALLATION FROM SINK TOP SOLID STAINLESS STEEL REMOTE HANDLE ASSEMBLY FOR SMOOTH, EASY OPERATION SPECIFICATION GRADE OVERFLOW ACCESSORIES AVAILABLE UNIVERSAL BODY PROVIDES BOTH 2" AND 1-1/2" (50 and 38mm) WASTE OUTLET CONNECTION AND CAN INSTANTLY CONVERT TO ACCEPT AN OVERFLOW ASSEMBLY ELIMINATING DOUBLE INVENTORIES FITS STANDARD 3-1/2"(90mm) SINK OPENING REPLACEMENT CRUMB CUP AVAILABLE... DSS-Y003 4-3/16" (106mm) 2-1/2" (63mm) 1-1/4" (31.7mm) S/S CAP NUT SINK OPENING 3-1/2"(90mm) MIN. TO 4"(100mm) MAX. 12" (300mm) CENTRE OF DRAIN TO ROTARY HANDLE HEAD GASKET SLIP WASHER S/S FLANGE NUT 2" NPS EXTERNAL THREAD 1-1/2" NPT INTERNAL THREAD DSS-8000 1-7/8" (47.6mm) 2-5/8"(67mm) OPTIONAL OVERFLOW ASSEMBLY E50-1000 1-7/8" (48mm) 1-1/4" (32mm) DIA. 1-1/4" (32mm) DIA. 14" (355mm) 1-7/8" (48mm) 18" (457mm) BRASS NICKEL PLATED W/STAINLESS STEEL FACEPLATE 1-5/16"(49mm) DIA. OPENING REQUIRED SLIP FIT FOR 1-1/4"(32mm) O.D.TUBING BRASS NICKEL PLATED ELBOW 1-1/4"(32mm) O.D.TUBING C40

Heavy-Duty Nickel Plated Solid Brass Rotary Drain PATENTED HEAVY- DUTY NICKEL PLATED SOLID BRASS ROTARY DRAIN HEAVY-DUTY NICKEL PLATED SOLID BRASS NSF LISTED CSA AND ANSI CERTIFIED PATENTED ROTARY VALVE PROVIDES FAST, UNOBSTRUCTED WATER EVACUATION TWIST LOCK RECESSED REMOVABLE BEEHIVE CRUMB-CUP PREVENTS CLOGGING AND INSURES CONTINUOUS WATER FLOW SELF-ADJUSTING HEAT AND CHEMICAL RESISTANT TEFLON SEALS ELIMINATE COSTLY REPLACEMENT OF O-RINGS AND CONVENTIONAL GASKETS 3 TIMES THE FLOW RATE OF CONVENTIONAL LEVER DRAINS FITS STANDARD 3-1/2" (90mm) SINK OPENING PATENTED COMPONENT CERTIFIED TO ANSI/ASME A112.18.1M FULL OPENING BALL VALVE ALLOWS ACCESS FOR SNAKING OR PLUNGING FROM SINK TOP... ELIMINATES COSTLY SERVICE CALLS UNIQUE BODY STYLE PROVIDES FAST INSTALLATION FROM SINK TOP SOLID STAINLESS STEEL REMOTE HANDLE ASSEMBLY FOR SMOOTH, EASY OPERATION SPECIFICATION GRADE UNIVERSAL BODY PROVIDES BOTH 2" AND 1-1/2" (50 and 38mm) WASTE OUTLET CONNECTION AND CAN INSTANTLY CONVERT TO ACCEPT AN OVERFLOW ASSEMBLY ELIMINATING DOUBLE INVENTORIES OVERFLOW ACCESSORIES AVAILABLE REPLACEMENT CRUMB CUP AVAILABLE... DSS-Y003 2-1/2" (63mm) 4-3/16" (106mm) SINK OPENING 3-1/2"(90mm) MIN. TO 4"(100mm) MAX. 12"(300mm) CENTRE OF DRAIN TO ROTARY HANDLE 1-1/4"(31.7mm) S/S CAP NUT DBN-8000 HEAD GASKET SLIP WASHER S/S FLANGE NUT 2" NPS EXTERNAL THREAD 1-1/2" NPT INTERNAL THREAD 1-7/8" (47.6mm) 2-5/8"(67mm) 1-7/8" (48mm) OPTIONAL OVERFLOW ASSEMBLY E50-1000 1-1/4" (32mm) DIA. 1-1/4" (32mm) DIA. 14" (355mm) 1-7/8" (48mm) 18" (457mm) BRASS NICKEL PLATED W/STAINLESS STEEL FACEPLATE 1-5/16"(49mm) DIA. OPENING REQUIRED SLIP FIT FOR 1-1/4"(32mm) O.D.TUBING BRASS NICKEL PLATED ELBOW 1-1/4"(32mm) O.D.TUBING C41

Lever Handle Waste Outlets UNIVERSAL STAINLESS STEEL DRAIN HANDLE SUPPORT D50-1000 14 Ga. B A 1-1/2" (38mm) 3/4" (19mm) 1/2" (12mm) 1-1/2" (38mm) 2"(50mm) 3"(75mm) 2 HOLES FOR 1/4" STUDS.075 (14 GA.) 1-1/4" (32mm) 3-1/2" 1-1/2" (89mm) (38mm) 1-1/2" (38mm) C For Lever and Twist Handle Outlets. LEVER HANDLE WASTE OUTLETS features... TROUBLE FREE FAST DRAINAGE POSITIVE SEALING ACTION CAST BRONZE BODY SNAP-IN STAINLESS STEEL STRAINERS SELF- CENTERING FACE FLANGES STAINLESS STEEL HANDLE 10-1/2" (267mm) SINK OP NG DIA. 3"(76mm) 3"(76mm) 3-1/2"(89mm) NPS 1-1/2" 2" 1-1/2" FACE FLANGE DIA. 4"(101mm) 4"(101mm) 4-1/2"(114mm) STRAINER TYPE FLAT MODEL NO. D10-4161 D10-4160 D10-7300 LEVER HANDLE WASTE OUTLETS 3-1/2"(89mm) 2" 4-1/2"(114mm) D10-7400 REF. A SINK OP NG DIA. 3"(76mm) 3"(76mm) 3-1/2"(89mm) 3-1/2"(89mm) NPS 1-1/2" 2" 1-1/2" 2" FACE FLANGE DIA. 4"(101mm) 4"(101mm) 4-1/2"(114mm) 4-1/2"(114mm) STRAINER TYPE FLAT MODEL NO. D10-4151 D10-4150 D10-7310 D10-7410 LEVER HANDLE WASTE OUTLETS with OVERFLOW OUTLET REF. B SINK OP NG DIA. 3"(76mm) 3"(76mm) 3-1/2"(89mm) 3-1/2"(89mm) NPS 1-1/2" 2" 1-1/2" 2" FACE FLANGE DIA. 4"(101mm) 4"(101mm) 4-1/2"(114mm) 4-1/2"(114mm) STRAINER TYPE FLAT MODEL NO. D10-4591 D10-4590 D10-7315 D10-7415 LEVER HANDLE WASTE OUTLETS with OVERFLOW ASSEMBLY REF. C NOTE: ALL SINK CONTACT COMPONENTS ARE STAINLESS STEEL. ALL OTHER COMPONENTS ARE NICKEL PLATED TO MATCH STAINLESS STEEL. 2" NPS FEMALE TO 1-1/2" NPT MALE NICKEL PLATED REDUCER AVAILABLE...SPECIFY NO. E30-7744. C42

Twist Handle Waste Outlets A B C TWIST HANDLE WASTE OUTLETS features... TROUBLE FREE FAST DRAINAGE POSITIVE SEALING ACTION CAST BRONZE BODY SNAP-IN STAINLESS STEEL STRAINERS SELF-CENTERING FACE FLANGES STAINLESS STEEL HANDLE 12" (304mm) SINK OP NG DIA. 3"(76mm) 3"(76mm) 3-1/2"(89mm) NPS 1-1/2" 2" 1-1/2" FACE FLANGE DIA. 4"(101mm) 4"(101mm) 4-1/2"(114mm) STRAINER TYPE FLAT MODEL NO. D50-4161 D50-4160 D50-7100 TWIST HANDLE WASTE OUTLETS 3-1/2"(89mm) 2" 4-1/2"(114mm) D50-7200 REF. A SINK OP NG DIA. 3"(76mm) 3"(76mm) 3-1/2"(89mm) 3-1/2"(89mm) NPS 1-1/2" 2" 1-1/2" 2" FACE FLANGE DIA. 4"(101mm) 4"(101mm) 4-1/2"(114mm) 4-1/2"(114mm) STRAINER TYPE FLAT MODEL NO. D50-4151 D50-4150 D50-7110 D50-7210 TWIST HANDLE WASTE OUTLETS with OVERFLOW OUTLET REF. B SINK OP NG DIA. 3"(76mm) 3"(76mm) 3-1/2"(89mm) 3-1/2"(89mm) NPS 1-1/2" 2" 1-1/2" 2" FACE FLANGE DIA. 4"(101mm) 4"(101mm) 4-1/2"(114mm) 4-1/2"(114mm) STRAINER TYPE FLAT MODEL NO. D50-4591 D50-4590 D50-7115 D50-7215 TWIST HANDLE WASTE OUTLETS with OVERFLOW ASSEMBLY REF. C NOTE: ALL SINK CONTACT COMPONENTS ARE STAINLESS STEEL. ALL OTHER COMPONENTS ARE NICKEL PLATED TO MATCH STAINLESS STEEL. 2" NPS FEMALE TO 1-1/2" NPT MALE NICKEL PLATED REDUCER AVAILABLE... SPECIFY NO. E30-7744. C43

Parts List 22 23 24 25 7 6 5 4 3 2 19 20 8 10 12 21 26 15 9 11 13 16 14 20 19 1 18 17 PARTS LIST for LEVER and TWIST HANDLE WASTE OUTLETS ITEM NO. 3" SINK OPENING PART NO. 3-1/2" SINK OPENING PART NO. DESCRIPTION 1 1 1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 D10-X001 D10-X003 D10-X005 D10-X007 D10-X021 D10-Y001 D10-X009 D10-X011 D10-X013 - D50-X005 D50-X010 D50-0001 D50-X007 D50-X006 D10-X026 D10-X029 D10-X027 D10-X030 D10-0001 D10-X025 D10-X022 D10-X023 E48-4660 E50-4580 E01-4091 E02-4091 E50-X003 E50-X004 D10-X002 D10-X004 D10-X006 D10-X008 D10-X021 D10-Y001 D10-X010 D10-X012 D10-X014 D13-0002 D50-X005 D50-X010 D50-0001 D50-X007 D50-X006 D10-X026 D10-X029 D10-X027 D10-X030 D10-0001 D10-X025 D10-X022 D10-X023 E48-4660 E50-4580 E01-4091 E02-4091 E50-X003 E50-X004 1-1/2" NPS WASTE OUTLET BODY WITHOUT OVERFLOW OUTLET (NOT SHOWN) 2" NPS WASTE OUTLET BODY WITHOUT OVERFLOW OUTLET (NOT SHOWN) 1-1/2" NPS WASTE OUTLET BODY WITH OVERFLOW OUTLET 2" NPS WASTE OUTLET BODY WITH OVERFLOW OUTLET STOPPER "O" RING, NEOPRENE STEM VALVE WITH O-RING" HEAD GASKET FACE FLANGE, STAINLESS STEEL FLAT STRAINER, STAINLESS STEEL CRUMB CUP STRAINER, STAINLESS STEEL E-RING 2-5/8" (66mm) WASHER TWIST HANDLE ASSEMBLY RUBBER O-RING PACKING NUT (BRASS) TWIST MODEL BLACK THERMOPLASTIC KNOB PACKING NUT (BRASS) LEVER MODEL PACKING NUT BUSHING BRASS BALL LEVER HANDLE ASSEMBLY BODY BUSHING (LEVER MODEL) SLIP JOINT WASHER SLIP JOINT LOCKNUT ONE PIECE OVERFLOW ELBOW 14" (355mm) OVERFLOW HEAD FOR 1-1/4"(32mm) TUBING GASKET FLANGED LOCKNUT STAINLESS STEEL STRAINER FOR OVERFLOW HEAD STRAINER MOUNTING SCREW OVERFLOW HEAD BRASS NICKEL PLATED with STAINLESS STEEL FACEPLATE E50-4580 2"(50mm) DIA. CUTOUT IN SINK REQUIRED FOR OVERFLOW HEAD 1-7/8" (48mm) 1-1/4" (32mm) 2" (50mm) ELBOW BRASS NICKEL PLATED E48-4660 TUBING FORMED IN ONE PIECE. 1-1/4"(32mm) O.D. TUBING 18" (457mm) C44

Overflow Drains & Components OVERFLOW DRAINS and COMPONENTS STAINLESS STEEL DUO BASKET DRAINS with OVERFLOW ASSEMBLY SINK OP NG DIA. 3-1/2" (89mm) 3-1/2" (89mm) DUO BASKET DRAIN with OVERFLOW ASSEMBLY NPS 1-1/2" 1-1/2" FACE FLANGE DIA. 4-1/2" (114mm) 4-1/2" (114mm) E40-4890 E40-4895* NOTE: FURNISHED WITH OVERFLOW, BRASS TUBING, T" JOINT, COUPLING NUTS, GASKETS AND SEATING WASHERS. * E40-4895 IS TYPE 18-8 STAINLESS STEEL 2-5/8"(67mm) BRASS and NICKEL PLATED BRASS TAILPIECE ASSEMBLIES for 1", 1-1/2" and 2" DRAINS TAILPIECE ASSEMBLIES SIZE 1" NPS 1" NPS 1-1/2" NPS 1-1/2" NPS 2" NPS 2" NPS LENGTH 2" (50mm) 2" (50mm) 4" (100mm) 4" (100mm) 4" (100mm) 4" (100mm) MATERIAL BRASS BRASS N.P. BRASS BRASS N.P. BRASS BRASS N.P. E22-4070 E22-4071 E22-4120 E22-4121 E22-4130 E22-4131 NOTE: ALL TAILPIECES ARE FURNISHED WITH GASKET AND SLIPNUT. OVERFLOW ASSEMBLY for 1-1/2" DRAINS E51-1000 for use with... LEVER / TWIST HANDLE DRAINS, BASKET DRAINS and SINK DRAINS RUBBER O-RING VERY ECONOMICAL ELIMINATES OVERFLOW TUBES MAXIMIZES SINK SPACE EASY INSTALLATION 6" (152mm) 1-1/8" (28mm) 1-5/8" (41mm) 19-1/2" (495mm) MAX. CHROME PLATED BRASS UNIVERSAL CONTINUOUS WASTE END OUTLET, 3 COMPARTMENT E30-7703 OVERFLOW ASSEMBLY CONSISTS OF: NICKEL PLATED BRASS BRANCH TAILPIECE SUB ASSEMBLY, (2) STAINLESS STEEL CLAMPS, 32"(815mm) LONG RUBBER HOSE and CHROME PLATED ABS OVERFLOW HEAD. 15"(380mm) MAX. 8-1/2" (216mm) 4" (100mm) 30"(760mm) 1-1/2" NPS 30"(760mm) 1-1/2" NPS NICKEL PLATED BRASS REDUCER 2" NPS FEMALE TO 1-1/2" NPT MALE E30-7744 C45

Basket and Dipperwell Assemblies BASKET and DIPPERWELL ASSEMBLIES STAINLESS STEEL BASKET ASSEMBLY for BOX PATTERN DRAINS Ideal for... SCULLERY SINKS FLOOR TROUGHS KETTLE TROUGHS WASH DOWN TROUGHS THIS HEAVY DUTY STAINLESS STEEL BASKET ASSEMBLY WITH MULTIPLE STRAINERS AND REMOVABLE BASKET PERMITS EASY CLEANOUT SERVICE. NORMAL SERVICING PREVENTS CLOGGING AND ELIMINATES COSTLY PLUMBING REPAIRS THAT OCCUR WITH OTHER TYPE DRAINS. STAINLESS STEEL (3-PIECE) BASKET ASSEMBLY MODEL N0. D34-Y011 Also available as individual components STAINLESS STEEL COVER...D34-X017 STAINLESS STEEL STRAINER...D34-X016 STAINLESS STEEL BOWL...D34-X015 6-1/2"(165mm)DIA. STAINLESS STEEL DIPPERWELL ASSEMBLY COMPLETE WITH FAUCET K30-1010 features... FITS INTO 6"(150mm) DIAMETER OPENING TYPE 18-8 STAINLESS STEEL INNER AND OUTER SHELL 9-1/2"(240mm) OVERALL LENGTH COMPLETE WITH STAINLESS STEEL DRAIN AND 1-1/2"(38mm) O.D. x 4"(100mm) LONG BRASS NICKEL PLATED TAILPIECE HIGHLY POLISHED CHROME PLATED FAUCET Also available as individual components DIPPERWELL ASSEMBLY WITHOUT FAUCET...K30-1000 DIPPERWELL FAUCET ONLY...K22-3100 1/2" NPS MALE INLET FURNISHED WITH 1/4" NPT MALE UNION TAILPIECE AND MOUNTING HARDWARE FOR K22-3100 REPAIR KIT SPECIFY MODEL #K22-0010 5-1/2"(140mm)DIA. 7-1/16" (180mm) 3-1/4" (82mm) 4-3/4"(120mm)DIA. 2-1/4" (57mm) 1-7/8" (47mm) 3-1/4" (83mm) 2-1/2" (64mm) 6-3/4" (171mm) 6-9/16" (166mm) 3/8" (9mm) 2-1/4" (57mm) 1-5/8" (42mm) 3-1/8" (80mm) DIA. C46

NUMERICAL PAGE INDEX PAGE NO. PAGE NO. PAGE NO. PAGE NO. 1014A-10........C36 1014A-10A.......C36 1014B-05........C36 1014B-10B.......C36 1416A-12........C36 1620A-08........C36 1620A-10........C36 1620A-12........C36 1620A-14A.......C36 2020A-10........C36 2020A-12........C36 2020A-14A.......C36 2424A-14A.......C36 D10-4150........C42 D10-4151........C42 D10-4160........C42 D10-4161........C42 D10-4590........C42 D10-4591........C42 D10-7300........C42 D10-7310........C42 D10-7315........C42 D10-7400........C42 D10-7410........C42 D10-7415........C42 D10-X001........C44 D10-X002........C44 D10-X003........C44 D10-X004........C44 D10-X005........C44 D10-X006........C44 D10-X007........C44 D10-X008........C44 D10-X009........C44 D10-X010........C44 D10-X011........C44 D10-X012........C44 D10-X013........C44 D10-X014........C44 D10-X021........C44 D10-X022........C44 D10-X023........C44 D10-X025........C44 D10-X026........C44 D10-X027........C44 D10-X029........C44 D10-X030........C44 D10-Y001........C44 D34-X015........C46 D34-X016........C46 D34-X017........C46 D34-Y011........C46 D50-0001........C44 D50-1000........C42 D50-4151........C43 D50-4160........C43 D50-4161........C43 D50-4590........C43 D50-4591........C43 D50-7100........C43 D50-7110........C43 D50-7115........C43 D50-7200........C43 D50-7210........C43 D50-7215........C43 D50-X005........C43 D50-X006........C43 D50-X007........C43 D50-X010........C43 DBN-8000.......C41 DPL-8000........C39 DPL-8000-S......C39 DSS-8000........C40 DSS-Y003.......C40 DSS-Y007....... C40 E01-4091........C44 E02-4091........C44 E22-4070........C45 E22-4071........C45 E22-4120........C45 E22-4121........C45 E22-4130........C45 E22-4131........C45 E30-7703........C45 E30-7744........C45 E40-4890........C45 E40-4895........C45 E48-4660........C44 E50-1000........C40 E50-4580........C44 E50-X003........C44 E50-X004........C44 E51-1000........C45 E52-1000........C39 E80-2020........C38 E80-X010........C38 E80-X015........C38 FB14-162014.....C35 FB14-181814.....C35 FB14-182414.....C35 FB14-202008.....C35 FB14-202014.....C35 FB14-242414.....C35 FB16-121410.....C35 FB16-162012.....C35 FB16-181812.....C35 FB16-182412.....C35 FB16-202008.....C35 FB16-202012.....C35 FB16-242412.....C35 FB80-2020.......C35 GBS15-1112-Q....C31 GBS15-1116-Q....C31 GBS15-1118-Q....C31 GBS15-1124-Q....C31 GBS15-113030Q..C31 GBS15-1130-Q....C31 GBS15-1132-Q....C31 GBS15-1136-Q....C31 GBS15-1142-Q....C31 GBS15-1148-Q....C31 GBS15-4112-Q....C31 GBS15-4116-Q....C31 GBS15-4118-Q....C31 GBS15-4124-Q...C31 GBS15-413030Q..C31 GBS15-4130-Q...C31 GBS15-4132-Q...C31 GBS15-4136-Q...C31 GBS15-414030Q..C31 GBS15-4142-Q...C31 GBS15-4148-Q...C31 K11-X080........C33 K22-0010........C46 K22-3100........C46 K30-1000........C46 K30-1010........C58 K50-0001-6......C15 K50-0110........C15 K50-0111........C15 K50-5026-12......C8 K50-5032-18......C8 K50-X033........C15 K50-X117........C15 K50-X136........C33 K50-X137........C25 K50-X138........C25 K50-X138-S......C25 K50-X139........C33 K50-X178........C15 K50-X196........C40 K50-X197........C25 K50-X198........C25 K50-X234........C40 K50-Y012........C14 K50-Y016-44.....C14 K50-Y020........C14 K50-Y047........C14 K50-Y500........C14 K53-5026-12......C8 K53-5032-18......C8 K56-5026-12......C9 K56-5032-18......C9 K60-5026-12......C9 K60-5032-18......C9 K77-8002........C32 K77-8006-BR.....C32 K77-8102........C32 K77-8106-BR.....C32 K78-8106-BR.....C32 K80-9004........C34 K80-9006........C34 KCV-0375........C25 KCV-0500........C25 KCV-0750........C25 KHR-5635-E......C24 KHR-5635-ESS...C24 KHR-5635-O.....C24 KHR-5635-OSS...C24 KHR-600248.....C24 KHV-3850........C25 KN11-X000.......C34 KN11-X001.......C34 KN11-X002.......C34 KN11-X006.......C34 KN11-X008.......C34 KN11-X010.......C34 KN11-X012.......C34 KN11-X014.......C34 KN11-X016.......C34 KN11-X100.......C34 KN11-X101.......C34 KN11-X102.......C34 KN34-Y006.......C15 KN34-Y007.......C15 KN35-Y007.......C15 KN40-1000.......C14 KN41-4000.......C27 KN41-4001.......C27 KN41-4002.......C27 KN41-4006.......C27 KN41-4008.......C27 KN41-4010.......C27 KN41-4012.......C27 KN41-8000.......C28 KN41-8001.......C28 KN41-8002.......C28 KN41-8006.......C28 KN41-8008.......C28 KN41-8010.......C28 KN41-8012.......C28 KN41-Y006.......C15 KN41-Y007.......C15 KN43-4050.......C25 KN45-4000.......C27 KN45-4001.......C27 KN45-4002.......C27 KN45-4006.......C27 KN45-4008.......C27 KN45-4010.......C27 KN45-4012.......C27 KN45-8000.......C28 KN45-8001.......C28 KN45-8002.......C28 KN45-8006.......C28 KN45-8008.......C28 KN45-8010.......C28 KN45-8012.......C28 KN50-0200.......C15 KN50-0220-12....C14 KN50-0210.......C14 KN50-1000........C6 KN50-1000-BR.....C6 KN50-2000.......C13 KN50-2000-VB....C13 KN50-3000.......C12 KN50-3000-VB....C12 KN50-X025.......C14 KN50-X075.......C33 KN50-X076.......C33 KN50-X120.......C33 KN50-X120-S.....C33 KN50-X122.......C33 KN50-X127.......C33 KN50-X128.......C33 KN50-X129.......C33 KN50-X148.......C33 KN50-X201.......C33 KN50-X201-H.....C33 KN50-Y002.......C14 KN50-Y004-20....C14 KN50-Y004-26....C14 KN50-Y004-44....C14 KN50-Y004-60....C14 KN50-Y004-72....C14 KN50-Y004-96....C14 KN50-Y006.......C15 KN50-Y007.......C15 KN50-Y010-20....C14 KN50-Y010-26....C14 KN50-Y010-44....C14 KN50-Y010-60....C14 KN50-Y010-72....C14 KN50-Y010-96....C14 KN50-Y027.......C15 KN50-Y030.......C14 KN50-Y031.......C14 KN50-Y102.......C14 KN51-9000.......C21 KN51-9000-R.....C21 KN51-9001.......C21 KN51-9001-R.....C21 KN51-9002.......C21 KN51-9002-R.....C21 KN51-9006.......C20 KN51-9008.......C20 KN51-9010.......C20 KN51-9012.......C20 KN51-9014.......C20 KN51-9016.......C20 KN52-9012.......C23 KN53-1000........C6 KN53-1000-BR.....C6 KN53-2000.......C13 KN53-2000-VB....C13 KN53-3000.......C12 KN53-3000-VB....C12 KN54-8000.......C17 KN54-8000-R.....C17 KN54-8001.......C17 KN54-8001-R.....C17 KN54-8002.......C17 KN54-8002-R.....C17 KN54-8006.......C16 KN54-8008.......C16 KN54-8010.......C16 KN54-8012.......C16 KN54-8014.......C16 KN54-8014.......C16 KN54-8016.......C16 KN54-8018.......C17 KN55-7006.......C15 KN55-7008.......C15 KN55-7010.......C15 C47

NUMERICAL PAGE INDEX PAGE NO. PAGE NO. PAGE NO. PAGE NO. KN55-7012.......C15 KN55-7014.......C15 KN55-7016.......C15 KN55-Y010.......C15 KN55-Y011.......C15 KN56-1000........C7 KN56-1000-BR.....C7 KN56-2000.......C13 KN56-2000-VB....C13 KN56-3000.......C12 KN56-3000-VB....C12 KN57-4000.......C19 KN57-4000-R.....C19 KN57-4001.......C19 KN57-4001-R.....C19 KN57-4002.......C19 KN57-4002-R.....C19 KN57-4006.......C18 KN57-4008.......C18 KN57-4010.......C18 KN57-4012.......C18 KN57-4014.......C18 KN57-4016.......C18 KN57-4018.......C19 KN58-4012.......C23 KN60-1000........C7 KN60-1000-BR.....C7 KN60-2000.......C13 KN60-2000-VB....C13 KN60-3000.......C12 KN60-3000-VB....C12 KN60-Y004.......C15 KN60-Y005.......C15 KN60-Y006.......C15 KN60-Y010.......C14 KN61-8000.......C19 KN61-8000-R.....C19 KN61-8001.......C19 KN61-8001-R.....C19 KN61-8002.......C19 KN61-8002-R.....C19 KN61-8006.......C18 KN61-8008.......C18 KN61-8010.......C18 KN61-8012.......C18 KN61-8014.......C18 KN61-8016.......C18 KN61-8018.......C19 KN62-8012.......C23 KN63-1000.......C10 KN63-1000-BR....C10 KN63-2000.......C13 KN63-2000-VB....C13 KN63-3000.......C12 KN63-3000-VB....C12 KN63-Y005.......C33 KN64-9000.......C21 KN64-9000-R.....C21 KN64-9001.......C21 KN64-9001-R.....C21 KN64-9002.......C21 KN64-9002-R.....C21 KN64-9006.......C20 KN64-9008.......C20 KN64-9010.......C20 KN64-9012.......C20 KN64-9014.......C20 KN64-9016.......C20 KN65-9012.......C23 KN67-6000.......C19 KN67-6000-R.....C19 KN67-6001.......C19 KN67-6001-R.....C19 KN67-6002.......C19 KN67-6002-R.....C19 KN67-6006.......C18 KN67-6008.......C18 KN67-6010.......C18 KN67-6012.......C18 KN67-6014.......C18 KN67-6016.......C18 KN67-6018.......C19 KN69-1000.......C10 KN69-1000-BR....C10 KN69-2000.......C13 KN69-2000-VB....C13 KN69-3000.......C12 KN69-3000-VB....C12 KN70-9000.......C22 KN70-9000-R.....C22 KN70-9001.......C22 KN70-9001-R.....C22 KN70-9002.......C22 KN70-9002-R.....C22 KN70-9006.......C22 KN70-9008.......C22 KN70-9010.......C22 KN70-9012.......C22 KN70-9014.......C22 KN70-9016.......C22 KN70-9018.......C22 KN71-1000.......C11 KN71-1000-BR....C11 KN71-2000.......C13 KN71-2000-VB....C13 KN71-3000.......C12 KN71-3000-VB....C12 KN72-9000.......C26 KN72-9000-R.....C26 KN72-9001.......C26 KN72-9001-R.....C26 KN72-9002.......C26 KN72-9002-R.....C26 KN72-9006.......C26 KN72-9008.......C26 KN72-9010.......C26 KN72-9012.......C26 KN72-9014.......C26 KN72-9016.......C26 KN72-9018.......C26 KN73-1000.......C11 KN73-1000-BR....C11 KN73-2000.......C13 KN73-2000-VB....C13 KN73-3000.......C12 KN73-3000-VB....C12 KN74-9000.......C26 KN74-9000-R.....C26 KN74-9001.......C26 KN74-9001-R.....C26 KN74-9002.......C26 KN74-9002-R.....C26 KN76-9010.......C22 KN76-9012.......C22 KN83-4104-CE4...C29 KN83-4100-RE4...C29 KN84-8102-RS4...C30 KN84-8105-CE4...C30 KN84-8201-RS....C30 KN91-0100.......C34 KS10-1000.......C31 KS20-9310.......C31 KVB-6000........C25 KVB-6045........C25 POWERS PROSERIES COMMERCIAL PLUMBING LAVATORY CONFIGURATOR SPOUT STYLE R = RIGID TUBULAR SPOUT C = CAST SPOUT (CAST INTEGRAL WITH BODY) S = SWIVEL TUBULAR SPOUT AERATOR A = 0.5 GPM PCA SPRAY VANDAL PROOF B = 1.5 GPM MAX LAMINAR ANTIMICROBIAL & VANDAL PROOF C = 0.5 GPM PCA SPRAY D = 1.5 GPM MAX LAMINAR ANTIMICROBIAL E = 2.2 GPM MAX AERATED STREAM F = 2.2 GPM MAX AERATED STREAM VANDAL PROOF H = 2.2 GPM MAX AERATED STREAM VANDAL & HOSE PROOF S = 6.0 GPM MAX WIDE ROSE SPRAY TUBULAR SPOUT 55/64-27 FEMALE KN50-X201-A KN50-X201-F KN50-X120-A KN50-X120-F KN50-X120 KN50-X201 KN50-X201-H KN50-X120-S CAST SPOUT 15/16 MALE KN50-X203-A KN50-X203-F KN50-X121-A KN50-X121-F KN50-X121 KN81 2 3 4 5 6 7 8 HANDLE 1 = STD ENCORE LEVER w/saniguard K50-0110-Q 2 = CROSS w/saniguard K50-0111-Q (1 PAIR) 3 = CP DESIGNER K50-X117 (1 PAIR) 4 = 4" WRIST BLADE W/SANIGUARD K50-0001-Q (1 PAIR) 6 = 6" WRIST BLADE w/saniguard K50-0001-6Q (1 PAIR) BLANK = METERING VALVES ARE SPECIFIED SPOUT SWIVEL RIGID 00 = 3" GOOSENECK KN11-X000 KN11-X100 01 = 8" GOOSENECK KN11-X001 KN11-X101 02 = 6" GOOSENECK KN11-X002 KN11-X102 04 = 4" STRAIGHT CAST SPOUT (KN83 & KN85 ONLY) 05 = 5" STRAIGHT CAST SPOUT BASE (KN84 & KN86 ONLY) 06 = 6" SWIVEL SPOUT KN11-X006 08 = 8" SWIVEL SPOUT KN11-X008 10 = 10" SWIVEL SPOUT KN11-X010 12 = 12" SWIVEL SPOUT KN11-X012 VALVE 0 = 1/4 TURN STD ENCORE COMPRESSION VALVE W/BUILT IN CHECK (KN50-Y006/Y007) 1 = 1/4 TURN CERAMIC VALVE W/INLINE CHECK VALVE (KN50-Y006-CCV/Y007-CCV) 2 = SELF-CLOSING ADJUSTABLE METERING VALVE (KN84-X039, USE ONLY AERATORS A & C) INLET 4 = 4" Ctr-Ctr 1/2" NPSM INTEGRAL CAST INLETS (KN83 & KN85 ONLY) 8 = 5"-24" ADJUSTABLE HOSE 1/2- NPSM INLETS (KN84 & KN86 ONLY) C48 BODY 3 = DECK MOUNT FAUCET BODY WITH INTEGRAL CAST SPOUT, CHROME PLATED 4 = DECK MOUNT CONCEALED WIDESPREAD FAUCET SPOUT BASE & VALVE HOUSINGS, CHROME PLATED 5 = DECK MOUNT FAUCET BODY WITH INTEGRAL CAST SPOUT w/ POP-UP HOLE, CHROME PLATED 6 = DECK MOUNT CONCEALED WIDESPREAD FAUCET SPOUT BASE & VALVE HOUSINGS w/ POP-UP HOLE, CHROME PLATED

Representatives in your Area J.D.S. SALES LTD. 4 Lancaster Street St.John s, NL A1A 5P7 Phone: (709) 579-5771 Fax: (709) 579-1558 Email: jds@nf.sympatico.ca BARRETT SALES (1998) LTD. 352 Applecrest Drive Kentville, NS B4N 2Z4 Phone: (902) 678-6705 Fax: (902) 678-3335 Email: barrett.ns@ns.sympatico.ca BARRETT SALES (1998) LTD. 357 Grand Vallee Road Dieppe, NB EIA 6G5 Phone: (506) 854-3401 Fax: (506) 854-3401 Email: barrett3@nb.sympatico.ca BARRETT SALES (1998) LTD. P.O. Box 26 St. John, NB E2L 3X1 Phone: (506) 693-8630 Fax: (506) 642-6499 Email: barrett2@nb.aibn.com LES ENT. ROLAND LAJOIE 6221 Marivaux St-Leonard, QC H1P 3H6 Phone: (514) 328-6645 Fax: (514) 328-6131 Email: info@ent-lajoie.com LES ENT. ROLAND LAJOIE 23 du Buisson Pont Rouge, QC G3H 1X9 Phone: (418) 873-2500 Fax: (418) 873-2505 WALMAR MECHANICAL SALES 24 Gurdwara Road Nepean, ON K2E 8B5 Phone: (613) 225-9774 Fax: (613) 225-0673 Email: infomech@walmar.net Website: www.walmar.net DEVCO SPECIFICATIONS 324 Forest Hill Drive Kitchener, ON N2M 4H1 Phone: (519) 570-0988 Fax: (519) 570-3817 Email: devcomail@rogers.com MECH TECH SALES 1069 Gordon Avenue Sudbury, ON P3A 2V5 Phone: (705) 525-2543 Fax: (705) 525-0432 Email: bertlemay@sympatico GTA SALES TEAM Phone: (888) 208-8927 Fax: (888) 479-2887 Email: gtasales@wattscanada.ca MAR-WIN AGENCIES LTD. 1333 Clifton Street, Winnipeg, MB R3E 2V1 Phone: (204) 775-8194 Fax: (204) 786-8016 Email: marwin@mts.net D.C. SALES LTD. #10-6130-4th Street S.E. Calgary, AB T2H 2A6 Phone: (403) 253-6808 Fax: (403) 259-8331 Email: reception@dcsalesltd.com D.C. SALES LTD. 11420 142 Street Edmonton, AB T5M 1V1 Phone: (780) 496-9495 Fax: (780) 496-9621 Email: reception@dcsalesltd.com CON-CUR WEST MARKETING, INC. 71B Clipper Street Coquitlam, BC V3K 6X2 Phone: (604) 540-5088 Fax: (604) 540-5084 Email: dconte@concurwest.com Canadian Manufacturing & Sales Offices 5435 North Service Road Burlington, ON L7L 5H7 Phone: (905) 332-4090 Fax: (905) 332-7068 Toll-Free Customer Service Line: 1-888-208-8927