marking Compatible with EMC directive INTENAL STUCTUE (9/16-18UNF) 6 5 4 3 1 2 7 FEATUES Compact, lightweight and multi-functional generalpurpose pressure gauge. It is adopted welding integral structure with SUS304/316L at pressure receiving section. A pressure display function is substantial. (3 1/2digit, 7 segment LED, 2-color LED red / green change, Nondisplay mode) Two types of analog output, one is voltage output ),The other is current output. The gage pressure is (0 positive pressure), compound pressure range (negative pressure positive pressure),to support maximum of 3.5 MPa. Comply with IP65, CE Marking and UL certification obtained. 1 2 3 4 5 6 7 Part name Sensor module Sensor holder Adapter Housing Panel sheet Cable Material SUS304 Diaphragm SUS316L PBT (UL-94-HB) Polyester Vinyl chlorid resin (UL2844) MODEL NUMBE DESIGNATION P G - 7 5-1 0 2 - N V 2 B Series name ated pressure 102G 100kPa102 100kPa 103G 1.0MPa103. 1.0MPa 353G 3.5MPa353. 3.5MPa Switch output interface NNPN open collector PPNP open collector Analog output VVoltage output ACurrent output With M5 female screw 11 21 Pressure port BlankStem mount BBack mount
LIST OF MODEL NUMBES Pressure SW port output Stem Back Analog output Pressure range (ated range analog output ) The products marked are manufactured upon receipt of order basis. STANDAD SPECIFICATIONS Model number 102G 103G 353G 102 103 353 Pressure reference Gauge Gauge (Compound) ated pressure Pr(L) Pr(H) 0 100kPa 0 1.0MPa 0 3.5MPa 100 100kPa 0.1 1.0MPa 0.1 3.5MPa Maximum pressure Pmax 200kPa 2MPa 5MPa 200kPa 2MPa 5MPa Break-down pressure Pb 300kPa 3MPa 7MPa 300kPa 3MPa 7MPa Full-scale FS 100KPa 1MPa 3.5MPa 200kPa 1.1MPa 3.6MPa Pressure Medium Corrosive gases/liquids compatible with SUS304 or SUS316 General specifications Sealed liquid Silicone oil Operating voltage Vopr 10.8 30VDC (Including ripple percentage) Consumption current 50mA maximum (Not included current analog output) Protection grade IP65 of IEC Operating temp. -10 50 (Storage Temperature : -20 70 ) Operating humidity Insulation resistance Dielectric strength port types materials Net Weight 100MΩ minimum at DC500V between bundled leads and pressure port One minuts at AC500V between bundled leads and pressure port (1mA maximum leakage) Diaphragm SUS316L SUS304 Approx. 115±15g (incl. 2m cable)
STANDAD SPECIFICATIONS Analog output Switch output Pressure display Model number Number of outputs Switching capacity esidual voltage Hysteresis epeatability esponse Protection State indication Voltage output Vo esolution esponse Current output Io esolution esponse Display element Display cycle 102G 103G 353G 102 103 353 Two outputs (NPN/PNP) 30VDC / 100mA maximum 1.2V maximum (NPN) / 2.2V maximum (PNP), current 100mA 0 Approx 0.3Pr(H),(Adjustable) ±0.3 FS / eference temp. 25 ±2%FS (Integrated accuracy:including errors of setting, linearity, hystresis and thermal error.) Approx 5 ms (Digital filter settings : F0 ) Exists / Short circuit protection(switch Overload current detection :Approx 150mA minimum) SW monitor LED(2 points),lighted when the switch output is ON.(Pressure display inverted colors) 1 5V / Pr(L) Pr(H), F.S. : 4V ±2%F.S. (Integrated accuracy) /Measurement load resistance(1mωmaximum) Approx Approx Approx 1kΩ(Internal impedance) Approx 2ms maximum 4 20mA / Pr(L) Pr(H), F.S. : 16mA ±2%F.S. (Integrated accuracy) /Measurement load resistance(250ωmaximum) Approx Approx Vopr 18VDC : 50 300Ω, Vopr 18VDC : 50 500Ω Approx 2ms maximum 3 1/2 digits, 7 segment LED (ed/green) everse display selectable in tandem with SW1. 5 times /sec moving average (Integrated accuracy) ENVIONMENTAL CHAACTEISTICS Test item Vibration Shock Pressure cycling Moisture resistance Test conditionsat 25 ± 5 C) 10 500Hz 1.5mm maximum / 98.1m/s2, three directions, two hours each 490m/s2, three directions, three times each ated pressure, 106 cycles 40 C, 9095 %H, 240 hrs. Permissible change Pressure indication, switch operating pressure and analog output (zero and span) : ± 2%F.S. maximum during test
ENVIONMENTAL CHAACTEISTICS Test item Test conditionsat 25 ± 5 C) Permissible change EMI : EN55011: 2009, A1: 2010 Group 1, class B EMS : EN61326-1 : 2006 Table 2 EN61326-2-3 : 2006 Annex BB Pressure indication, switch operating pressure and analog output : ± 5 %F.S. maximum during test MULTIPLIE FACTO The multiplier factor is selectable by changing the value of third digit on the display during the operation setting. Code/Multiplier Factor Pressure ange / Display specification rated pressure 102G 102 103G 103 353G 353 The settings indicated by "-" on the table above are not selectable because of resolution. Either "1"for 102A, 102V, 102G, and 102) or "8" (for 103G, 103, 353G and 353) are set prior to delivery. Changes of the multiplier factor apply to display values. Also, note the changes reset switch setting value and hysteresis. SWITCH OUTPUT MODE SW output is selectable by changing the value of first digit on the display. SW Operation Code Switch Operation Mode Separate mode Window comparator mode Pressure setting (Operating point) HI operation L operation P1P2 or P1P2 Hysteresis Set 1Set 2 Set 3Set 4 A operation B operation P1P3 2H and P2P4 2H In the Separate mode, SW 1 corresponds to Setting 1 and SW2 corresponds to Setting 2. In the Window Comparator Mode, SW 1 corresponds to the Setting 1 lower limit and Setting 3 upper limit. Also. SW2 corresonds to the setting 2 lower limit and setting 4 upper limit. The Hysteresis H setting is common to SW 1 and SW 2 operations. When SW operation is changed between the Separate Mode and Window Comparator Mode, SW pressure settings that are set separately will be reset.
EXTENALS SPECIFICATION (unit:mm) Vertical installation type Unit:kPa/MPa 1/4Fittin SUS304,Width:14 LED-Cover:PBT MEANS OF ATTACHMENT (Option) Vertical installation type MADE IN JAPAN GAY ANALOG OUT420mA BLUE COMMON BOWNPOWE SUPPLY10.8 30VDCCLASS2 BLACKSWITCH1PNP 30V100mA max. WHITESWITCH2PNP 30V100mA max. -103-PA2 PESSUE ANGE-0.11.0M LOT. 1H1 Adoptor:PBT -M4 depth Metal insert BsNi Plating Cover:PBT Pressure port M0 depth6 Air intake Applicale te:4 The horizontal installation type MADE IN JAPAN -102-NV2B LOT.1H1 PESSUE ANGE-100100k BOWNPOWE SUPPY10.8 30VDCCLASS2 BLACKSWITCH1NPN 30V100mA max. WHITESWITCH2NPN 30V100mA max. GAY ANALOG OUT1 5V BLUECOMMON Adoptor:PBT core cale L000100 AW6,UL STLE:44 Wire color Brown Gray Black White Blue Shield Connection Power B Analog output Switch output 1 Switch output 2 Common The horizontal installation type 1/4 SUS304,Width:14 Cover:PBT -102-NV2B LOT.1H1 PESSUE ANGE-100100k BOWNPOWESUPPLY10.830VDCCLASS2 BLACKSWITCH1NPN30V100mAmax. WHITESWITCH2NPN30V100mAmax. GAYANALOGOUT15V BLUECOMMON -103-PA2 LOT. 1H1 PESSUE ANGE-0.11.0M BOWNPOWE SUPPLY10.830VDCCLASS2 BLACKSWITCH1PNP 30V100mA max. WHITESWITCH2PNP 30V100mA max. GAYANALOG OUT4 20mA) BLUE COMMON Panel holder cover Panel holder Accessories (sold separately) are available for common use with PG-30, PG-35, series. (P.173) INTENAL ELECTICAL SCHEMATICS NV/NA:NPN PV/PA:PNP PressureDisplay LED Power supply PressureDisplay LED Power supply Pressure Sensor Main circuit NPN/SWOutput circuits Aout SW1 SW2 Pressure Sensor Main circuit PNP/SW Output circuits SW1 SW2 Aout Frame Ground COM. COM.