Manual Series I 1700TT (S/N 2026NN-) Dual Valve Update Kit 1700TT Turbo-Till Manufacturing, Inc.! Read the operator s manual entirely. When you see this symbol, the subsequent instructions and warnings are serious - follow without exception. Your life and the lives of others depend on it Cover illustration may show optional equipment not supplied with standard unit. Copyright 2006 Printed 3/21/2006 586-169M
Great Plains Manufacturing, Inc. Corporate Office: PO. Box 5060 Salina, Kansas 67402-5060 USA
Assembly Instructions for 586-168A 1700TT Hydraulic Update Kit 1) Assemble the fittings in the down pressure valve as shown. Be sure to apply thread sealant to the threads on the gauge. 2) Mount the new down pressure valve as shown at the rear of the hitch frame. Use the ½ x 4 ½ bolts w/ lock washers and nuts to secure the mounting bracket. Use the ¼ x 2 ½ bolts, flat washers, lock washers and nuts to mount the valve. 3) Apply pipe thread sealer to the adapter (811-023C) fitting and screw it into the ½ FNPT Tee (811-855C) as shown. Apply Thread Sealer Here 811-255C 811-281C 811-584C 811-216C 811-584C 4) Disconnect hose from the filter at the front of the existing valve (2). Remove the filter and replace with a ¾ O-ring x ¾ JIC adapter (811-088C). 5) Screw the filter into adapter (811-023C) and reconnect the hose from the tractor to the filter. Attach one end of one of the 12 hoses to the tee and connect the other end to the JIC adapter at the front of the valve body as shown. Do this for both 12 hoses. 12 Hoses 6) Disconnect the return hose from the adapter at the rear of the existing down pressure valve. Insert the Tee (811-073C) and reattach the hose as shown. 7) Attach the 131 hose (22) to the straight fitting at the side of the new valve (3). Run this hose to the rear of the unit and attach to the base end of the left-hand fold cylinder as shown in the schematic. 811-073C 8) Remove the tee that is between the hose attached to the base end of the right hand fold cylinder and the hose, which comes from the existing pressure valve. Replace this tee with a straight adapter (811-430C).
9) Use the 42 hose (21) that you removed from the rear of the machine to connect the elbow (14) at the rear of the new valve (3) to the tee (17) that you inserted into the return line at the rear of the old valve (2). 10) This should complete the installation. Double check the hose routing with the schematic and then tighten all fittings and hoses. After tightening, slowly try to fold the unit while watching for leaks. If no leaks occur, fold and unfold machine several times to purge the air from the system. You are now ready to set the down pressure. Refer to the instructional page for the proper procedure for setting the down pressure with multiple valves.
Hydraulics Great Plains Mfg., Inc. 1700TT Hydraulic Update - Down Pressure Setup and Operation Note: This setup procedure is for tractors with closed-center or pressure compensated flow hydraulic systems. For open-center hydraulic systems contact your dealer for instructions. 1. Adjust the bypass valve by turning knob (1), Figure 2, clockwise all the way in and then backing out 1 full turn. 2. On tractor, adjust flow-control valve to low side of flow rate. NOTE: The faster the flow of oil through the system the greater potential for oil heating, premature wear or tractor damage. 3. Lock the fold hydraulic lever for continuous downward oil flow. 4. Adjust pressure reducing valves knob (2 & 3) on implement so the pressure gauges reads 1200 psi each. 5. While watching pressure gauges, slowly open bypass valve, knob (1) until gauges reads around 1100 psi. Pressure might rise and then fall off as knob is opened. If pressure exceeds 1400 psi during this step, the tractor flow is too high, reduce tractor flow. Lock bypass valve knob (1) at 1100 psi. 6. Finally adjust valve knob (2) and (3) to 450-500 psi pressure setting. This is a beginning pressure setting. Once you are in the field, these setting may need to change up or down. You should never need to run less than 300 psi or exceed 1000 psi. If you need to run that high of pressure, make sure the flow rate is turned down. Excessive flow can cause higher pressure readings. 7. In field operation, Lock the fold hydraulic lever for continuous downward oil flow. If a wing is running too high, increase pressure setting to the appropriate valve, knob (2 or 3), to level the wing. If a wing is running to deep, decrease the pressure setting with knob (2 or 3) on the appropriate wing valve. Make sure wing gauge wheels are properly set. 8. Caution: Never leave tractor valve centered when unfolded with machine in motion. Machine damage may occur when wings flex up or down.! Series I 2200TT & 3000TT Turbo Till 586-043M 1/30/2003 Figure 2 44
Great Plains Mfg., Inc. Hydraulics Hydraulic Fold System Dual Valve Update 1700TT (S/N 2026NN-) 00847 3/9/2006 586-169M
Hydraulics Great Plains Mfg., Inc. Hydraulic Fold System Dual Valve Update 1700TT (S/N 2026NN-) Ref Kent No. GP Part No. Part Description Comments 1. 810-490C CYL 4x24x2 Rod (Tie) 34.63 C.L. 1700TT. GP Seal Kit# 810-014C 2. 810-512C Valve, Bypass/Pressure Reducing with Check GP Seal Kit # 810-515C 3. 810-301C Valve, Pressure Reducing with Check 4. HF0190 810-300C 3000 PSI Oil Filled Pressure Gauge 5. 810-532C Filter, Inline 3/4 MORB 3/4 MJIC 6. 811-088C Adaptor, AD 3/4MORB 3/4MJIC 7. 811-063C Elbow, EL 3/4MJIC 3/4MORB 8. 196-430D Orifice Restrictor, ORPL 1/16 3/4MORB 9. 811-078C Tee, TE 3/4MJIC 10. 811-677C Adaptor, AD 9/16MORB 1/4FNPT 11. 811-023C Adaptor, AD 1/2MNPT 3/4FORB 12. 811-855C Tee, TE 1/2FNPT 13. 811-584C Adaptor, AD 9/16MORB 3/4MJIC 14. 811-216C Elbow, EL 3/4MJIC 9/16MORB 15. 811-281C Elbow, EL 3/8FNPT 9/16MORB 16. 811-255C Adaptor, AD 3/8MNPT 1/4FNPT 17. 811-073C Tee, TE 3/4MJIC 3/4MJIC 3/4FJIC 18. 811-430C Adaptor, AD 3/4MJIC 3/4MJIC 19. 811-882C HH3/8R2 152 3/4FJIC 3/4MORB 20. 841-150C HH3/8R2 12 1/2MNPT 3/4FJIC 21. 811-838C HH3/8R2 042 3/4FJIC 22. 841-011C HH3/8R2 131 3/4FJIC 23. 811-978C HH3/8R2 093 3/4FJIC 1700TT(S/N 2026NN-) 24. 811-839C HH3/8R2 074 3/4FJIC 25. 811-841C HH3/8R2 024 3/4FJIC 26. 811-915C Hydra Grip Handle - Green Extend 27. 811-916C Hydra Grip Handle - Green Retract 28. 811-919C Adaptor, AD 3/4 MORB 3/4 FORB (HG) 29. 548-003S HG Pair Green MORB-FORB Includes items 17 thru 19 30. 811-394C Coupler, CP 3/4FORB Male QD Poppet Type 586-169M 3/9/2006
Great Plains Manufacturing, Inc. Corporate Office: PO. Box 5060 Salina, Kansas 67402-5060 USA