2mm ") DI. POINT TO POINT SYSTEM PVC OR STEEL SYSTEM L84 CLL -800--600 TYPE I ND TYPE II OVERHED UNITS 4 6 ") ( 8 ") 6 8 ") ( -0 PLN VIEW 20 (8 28 8 ") ( 8 ") 4 ( -4") 2 (4 ( 8 ") 28 ( 8 ") THE TYPE I OVERHED UNIT SUITS NRROW ND TLLER MOUNTING SPCES. TYPE I ND TYPE II OVERHED UNITS MY E INTERCHNGED USING ONE OF ECH. THE UNITS CN E WLL MOUNTED ND SHOULD E MOUNTED LEVEL SECURING UNITS THROUGH THE CK. 2mm ") PVC ND 2mm ") STEEL CNNOT E USED ON THE SME RUN. THE ENTIRE SYSTEM MUST E LL PVC OR LL STEEL (OR MILL WRPPED STEEL FOR URIED). 2mm ") DI. PNEUMTIC THIRD NGLE "LL DIMENSIONS ND DESIGN CRITERI PROJECTION FILE NO. 8-4 REV. 2 SUJECT TO CHNGE W ITHOUT NOTICE" PGE OF 8 ") 22 ( 8 ") 6 PLN VIEW 6 62 8 28 46 ( -6 2 (") 2 (8 6 ") 460 ( -6 8 ") 8 ") 2 ") ( -0 8 ") ( 0 TYPE I OVERHED UNIT 2-0200-000 2mm ") STEEL 2-0202-000 2mm ") PVC 2 ( - 6 ") 2 6 ") 8 4 2 ") ( -0 6 ") ( 6 ") TYPE II OVERHED UNIT 64 20 2 ") ( -4") 8 ") (0 2 2 (4-4") 8 ") ( -0 (4 8 ") - 4 8 8 ") ( 8 ") -0 ( 8 ") 2-02028-000 2mm ") STEEL 2-020-000 2mm ") PVC ( -0 8 ") ELECTRICL PNEL ELECTRICL PNEL THE TYPE II OVERHED UNIT FITS TLE OR COUNTER TOPS ND WIDER, SHORTER LOCTIONS. THE UNIT CN E WLL MOUNTED ND SHOULD E MOUNTED LEVEL SECURING UNIT THROUGH THE CK. 2mm ") PVC ND 2mm ") STEEL CNNOT E USED ON THE SME RUN. THE ENTIRE SYSTEM MUST E LL PVC OR LL STEEL (OR MILL WRPPED STEEL FOR URIED). 2mm ") DI. PNEUMTIC
OVER DELIVERY 2mm ") PVC PNEUMTIC SYSTEM DETIL ELOW SHOWS OVERHED 2mm ") PVC ND COMPONENTS. PVC ND COMPONENTS CN LSO E USED FOR UNDER DELIVERY SYSTEMS EXCEPT IN DIRECT URIED INSTLLTIONS. SEE SHEET 4 OF FOR 2mm ") STEEL DETILS ND COMPONENTS THT CN LSO E USED FOR OVERHED DELIVERY RUNS. THIRD NGLE "LL DIMENSIONS ND DESIGN CRITERI PROJECTION FILE NO. 8-4 REV. 2 SUJECT TO CHNGE W ITHOUT NOTICE" PGE 2 OF VRIES TYPE II OVERHED UNIT -02028-000 STEEL) -020-000 PVC),82mm -0") CORDS STNDRD PVC CONFIGURTION CONSISTS OF: ) 0 DEGREE PVC ENDS-4mm ( -0") RDIUS ) 0mm (0-0") LENGTHS OF 2mm ") DI. PVC TUING ) PVC COUPLINGS ) PVC NO HU COUPLINGS PVC CEMENT PVC CLENER () 2mm ") PVC HNGERS DDITIONL PVC SECTIONS, ENDS, ND PRTS TO E ORDERED SEPRTELY. 2mm ") PVC COUPLING 2mm ") PVC COUPLING 2mm ") PVC TUING NO-HU COUPLING 4mm ( -0") 4mm ( -0") RDIUS PVC END RDIUS PVC END UNITS MUST E LOCTED WITHIN 24mm -0") OF N ELECTRICL OUTLET. RE NOT SUITLE S DISCONNECTS E.C. TO SUPPLY SUITLE QUICK DISCONNECT OX T ECH UNIT. 2mm ") PVC COUPLING INDICTES PRTS INCLUDED IN STNDRD SINGLE PVC POINT TO POINT SYSTEM CONFIGURTION. SEE PRTS ND QUNTITIES IN NOTE OVE. STEEL CN E USED FOR OVERHED INSTLLTIONS SEE SHEET 4 OF FOR STEEL COMPONENTS. TYPE I OVERHED UNIT -0200-000 STEEL) -0202-000 PVC) 2mm ") PVC COUPLING 2mm ") PVC TUING NO-HU COUPLING,82mm -0") CORDS ELECTRICL REQUIREMENTS FOR OVERHED UNITS OWNER S ELECTRICL CONTRCTOR TO PROVIDE () DUPLEX OUTLET T ECH OWNER S ELECTRICL CONTRCTOR TO PROVIDE CONDUIT ON ) 20 VC, 60Hz, SINGLE-PHSE, (W) 20 MP DEDICTED RNCH CIRCUIT. TO UILDING ELECTRICL SUPPLY PNEL. LOCTE WITHIN,24mm -0") OF UNIT. 2,48 (8-0")
2mm ") DI. POINT TO POINT SYSTEM PVC OR STEEL SYSTEM TYPE I ND TYPE II UNDERGROUND UNITS CLL -800--600 ( -0 8 ") THE TYPE I UNDERGROUND UNIT SUITS NRROW ND TLLER SPCES. TYPE I ND TYPE II UNDERGROUND UNITS MY E INTERCHNGED USING ONE OF ECH. THE UNIT CN E WLL MOUNTED ND SHOULD E MOUNTED LEVEL SECURING THROUGH THE CK. 6 ") 6 6 ") 2mm ") PVC ND 2mm ") STEEL CNNOT E USED ON THE SME RUN. THE ENTIRE SYSTEM MUST E LL PVC OR LL STEEL (OR MILL WRPPED STEEL FOR URIED). THIRD NGLE "LL DIMENSIONS ND DESIGN CRITERI PROJECTION FILE NO. 8-4 REV. 2 SUJECT TO CHNGE W ITHOUT NOTICE" PGE OF 02 (4") 200 ( - 2 8 6 2mm ") DI. PNEUMTIC 4 6 ") ( 2 ") ( -0 2 ") ( -4") ( 6 ") 26 (8 2 ") ( -0 8 ") ( -6 2 ") 4 2 2 6 ") 4 6 ") 28 OTTOM VIEW TYPE I UNDERGROUND UNIT ( 8 ") ( 20 (8 8 ") ( ( 8 ") 2-020-000 2mm ") STEEL 2-02022-000 2mm ") PVC 22 ( 8 ") 2mm ") DI. PNEUMTIC 6 4 ( - 2 ") 2 ") 60 2 OTTOM VIEW TYPE II UNDERGROUND UNIT 4 8 ") ( -4") (0 6 ") 8 ") - 860 8 ") ( 8 ") ( -0 8 ") - 02 (4") 28 ( 8 ") ( 8 ") 2-0202-000 2mm ") STEEL 2-02020-000 2 mm ") PVC ( -0 8 ") ELECTRICL PNEL 2 ") DI. PNEUMTIC ELECTRICL PNEL 2 ") DI. PNEUMTIC THE TYPE II UNDERGROUND UNIT FITS TLE OR COUNTER TOPS ND WIDER, SHORTER LOCTIONS. THE UNIT CN E WLL MOUNTED ND SHOULD E MOUNTED LEVEL SECURING THE UNIT THROUGH THE CK. 2mm ") PVC ND 2mm ") STEEL CNNOT E USED ON THE SME RUN. THE ENTIRE SYSTEM MUST E LL PVC OR LL STEEL (OR MILL WRPPED STEEL FOR URIED).
UNDER DELIVERY 2mm ") STEEL OR PVC PNEUMTIC SYSTEM DETIL ELOW SHOWS UNDER DELIVERY 2mm ") STEEL ND COMPONENTS. PVC ND COMPONENTS CN LSO E USED FOR UNDER DELIVERY SYSTEMS EXCEPT IN DIRECT URIED INSTLLTIONS. SEE SHEET 2 OF FOR 2mm ") PVC DETILS ND COMPONENTS. STNDRD STEEL CONFIGURTION CONSISTS OF: ) 0 DEGREE STEEL ENDS-4mm ( -0") RDIUS ) 80mm -6") LENGTHS OF 2mm ") DI. STEEL TUING () STEEL CLMP SLEEVES (4) 828mm -0") SECTIONS -LL THRED (4) 0mM (0-0") SECTIONS - UNISTRUT () STEEL HNGERS STNDRD MILLWRPPED STEEL CONFIGURTION CONSISTS OF: ) 0 DEGREE MILLWRPPED STEEL ENDS-4mm ( -0") RDIUS ) 80mm -6") LENGTHS OF MILLWRPPED 2mm ") DI. STEEL TUING (4) STEEL CLMP SLEEVES () STEEL SOLID SLEEVES () SHRINK SLEEVES DDITIONL STEEL SECTIONS, ENDS, ND PRTS TO E ORDERED SEPRTELY. STNDRD PVC CONFIGURTION CONSISTS OF: ) 0 DEGREE PVC ENDS-4mm ( -0") RDIUS ) 0mm (0-0") LENGTHS OF 2mm ") DI. PVC TUING ) PVC COUPLINGS ) PVC NO HU COUPLINGS PVC CEMENT PVC CLENER () 2mm ") PVC HNGERS DDITIONL PVC SECTIONS, ENDS, ND PRTS TO E ORDERED SEPRTELY. THIRD NGLE PROJECTION UNITS MUST E LOCTED WITHIN 24mm -0") OF N ELECTRICL OUTLET. RE NOT SUITLE S DISCONNECTS E.C. TO SUPPLY SUITLE QUICK DISCONNECT OX T ECH UNIT. TYPE II UNDERGROUND UNIT -0202-000 STEEL) -0202-000 PVC) TYPE I UNDERGROUND UNIT -020-000 STEEL) -02022-000 PVC),82mm -0") CORDS,82mm -0") CORDS "LL DIMENSIONS ND DESIGN CRITERI FILE NO. 8-4 REV. 2 SUJECT TO CHNGE W ITHOUT NOTICE" PGE 4 OF 20mm (8") SQURE OR ROUND FLOOR OPENING Y OWNER S GENERL CONTRCTOR FOR UNDER DELIVERY SYSTEMS, PVC, STEEL, OR STEEL MILLWRPPED FOR DIRECT URIED INSTLLTIONS MY E USED. CTUL DETIL OF UNDER DELIVERY ND COMPONENTS WILL E DETERMINED, SED ON TYPE OF REQUIRED. THE ENTIRE SYSTEM MUST E LL PVC OR LL STEEL (OR MILLWRPPED STEEL) S 4mm ( -0") RDIUS END ELECTRICL REQUIREMENTS FOR UNDERGROUND UNITS OWNER S ELECTRICL CONTRCTOR TO PROVIDE () DUPLEX OUTLET T ECH ON ) 20 VC, 60Hz, SINGLE-PHSE, (W) 20 MP DEDICTED RNCH CIRCUIT. LOCTE WITHIN,24mm -0") OF UNIT. VRIES 4mm ( -0") RDIUS END 20mm (8") SQURE OR ROUND FLOOR OPENING Y OWNER S GENERL CONTRCTOR OWNER S ELECTRICL CONTRCTOR TO PROVIDE CONDUIT TO UILDING ELECTRICL SUPPLY PNEL.
OPERTION: ING MODE OF OPERTION: SYSTEMS RE PRESSURE / PRESSURE ND HVE TURO COMPRESSORS T ECH UNIT. THE COMPRESSORS RE CTIVTED Y N ELECTRONIC TIMER. POSITIVE PRESSURE WITHIN THE UNIT S SELED COMPRTMENT PUSHES THE CRRIER FROM ING UNIT TO RECEIVING UNIT THROUGH SINGLE INTER CONNECTING PNEUMTIC. TO CRRIER: LOD CRRIER PLCING IT IN THE / RECEIVE COMPRTMENT. SECURE THE ND PUSH THE UTTON. THE RECEIVING UNIT INDICTOR RED ND WHITE LIGHTS WILL GO ON ND THE RECEIVING WILL UTOMTICLLY LOCK. FTER THE ING COMPRESSOR HS STOPPED THE RED LIGHT WILL GO OUT ND THE RECEIVING WILL UNLOCK. THE WHITE LIGHT WILL REMIN LIT UNTIL THE RECEIVING IS OPENED. CRRIER SPEED CONTROL: STNDRD IN 2mm ") DI. SYSTEMS RELIEF VLVE VENTS SYSTEM PRESSURE ND LLOWS THE CRRIER TO FLL UNED INTO THE RECEIVING STTION. SECOND VLVE SIMULTNEOUSLY UILDS UP CK PRESSURE TO CUSHION THE CRRIERS FLL ON THE RRIVL PD. THIRD NGLE PROJECTION PNEUMTIC SYSTEM CRRIERS ( - 8") "LL DIMENSIONS ND DESIGN CRITERI FILE NO. 8-4 REV. 2 SUJECT TO CHNGE W ITHOUT NOTICE" PGE OF 2 ") 6 ") DISC END FOR LODS UP TO 2.2kg LS.) ND DISTNCES TO 0 METERS (,000 FEET) PROVIDES mm (4 8") USEFUL DI. PPROXIMTE CRRIER RTE OF SPEED T 8 METERS FEET) PER SECOND. 2 ") 4 2 6 ") 4 ( - 2 ") 2-02026-000 - CRRIER FOR USE IN PVC TUING ONLY DISC STEEL CP CLER PLEXIGLSS 22 ( 6 ") ( 6 ") (8 8 ") 8 ") ( 8 ") OPENING END HIGH DENSITY PLSTIC CONSTRUCTION (POLYETHYLENE) 60 LETHER 6 END CP HRD PLSTIC SNP LOCKS LTCH END 2-022-000 - CRRIER FOR USE IN STEEL TUING ONLY LETHER HINGE SNP LOCKS LETHER