INSTALLATION INSTRUCTIONS Accessory Application Publications No. All 30482 S 2006 PILOT Issue Date P/N 08F23-S9V-100A SEP 2005 PARTS LIST Left front trim piece Right front trim piece Left rear trim piece Right rear trim piece 4 Brackets A TOOLS AND SUPPLIES REQUIRED Phillips screwdriver Flat-tip screwdriver Ratchet 10 mm Socket Drill 3 mm and 7 mm Drill bit 1-1/8" (28 mm) Hole saw Center punch File Torque wrench Masking tape Isopropyl alcohol Shop towel INSTALLATION Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by do-it-yourselfers. NOTE: An optional full nose mask cannot be used after the chrome bumper trim pieces are installed. 6 Brackets B 10 Flange nuts Template Be extremely careful not to damage the body paint finish. To prevent damage, rest the front bumper on a blanket during the installation. This bumper trim pieces should only be installed if the ambient air temperature is below 65 F (15 C) or above. To allow the adhesive to cure, do not wash the vehicle for 24 hours. 2005 American Honda Motor Co., Inc. - All Rights Reserved. AII 30482 (0509) 08F23-S9V-1A00-91 1 of 6
Installing the Front Bumper Trim Pieces 1. Open the hood. Remove the front bulkhead cover (13 clips). 3. Bend the template under, and align the line. Align the hole of the template with the hole of the front bumper, and secure the template with the pieces of masking tape. Note the direction of the template. CLIPS (13) Align the hole. TEMPLATE Vehicle inside direction. FELT-TIP PEN ARROW of the template ARROW BULKHEAD COVER 4N23032P CHARACTER LINE FELT-TIP PEN 38 mm SCRIBE 2. Remove the front bumper (two short clips, two self-tapping screws, four bolts, and two long clips). To prevent damage, rest the bumper on a blanket. LONG CLIP 4. Using a felt-tip pen, add the arrow mark to the front bumper against the arrow mark on the template. Drill point is top of arrow. 5622010P 5. Using a tape measure and felt-tip pen, measure and mark the front bumper as shown. BOLT SHORT CLIP BOLT 4N18022P 2 of 6 AII 30482 (0509) 2005 American Honda Motor Co., Inc. - All Rights Reserved.
6. On the inside of the front bumper, locate the two marks on the left side. Center-punch each of the two marks you made. 10. Place the left front trim piece on the front bumper, and adjust it until it fits snug. Using strips of masking tape, mark the location of the trim piece. ARROW (made in step 4.) DRILL POINT (made in step 5.) LEFT DRILL (3 mm 7 mm bit) CENTER-PUNCH SCRIBE [+] 5622020P 7. While wearing eye protection, drill a 7 mm hole through each of the center-punched marks. First drill with a 3 mm bit, and finish with a 7 mm bit. Remove any burrs from the edges of the holes. 8. On the inside of the front bumper, locate the two marks on the left side. Center-punch each of the two scribe marks. 4N23050P 11. Attach a strip of masking tape to the ends of the four adhesive backings shown, and peel back 2 to 3 inches from the ends. Fold the ends up and tape them to the front of the trim piece. Remove the remaining two adhesive backings. ADHESIVE BACKING (Remove.) Attach a strip of masking tape to the end and peel back 2 to 3 inches from that end. Fold the end up, and tape them to the trim piece. ADHESIVE BACKING (Remove.) LEFT CENTER-PUNCH Attach a strip of masking tape to the end and peel back 2 to 3 inches from that end. Fold the end up, and tape them to the trim piece. 1-1/8" (28 mm) HOLE SAW DRILL (3 mm bit) 4N23042P 4N23061P 9. While wearing eye protection, drill an 1-1/8" (28 mm) hole through each of the center-punched marks. First drill with a 3 mm bit, and finish with an 1-1/8" (28 mm) hole saw. Remove any burrs from the edges of the holes. 2005 American Honda Motor Co., Inc. - All Rights Reserved. AII 30482 (0509) 3 of 6
12. Using isopropyl alcohol on a shop towel, clean the area where the trim piece will attach. 15. Torque the flange nuts to 10 N m (7.3 lb-ft). BRACKET FLANGE NUT While holding light pressure, slowly and carefully remove the adhesive backing. LEFT TRIM PIECE PIN FLANGE NUTS (2) Torque to 10 N m (7.3 lb-ft) BRACKETS A (2) PIN LEFT LEFT ATTACHING SURFACE (Clean with Isopropyl alcohol.) LEFT 7 mm HOLE (2: Made in step 7.) 28 mm HOLE (2: Made in step 9.) 4N23071P 13. Position the left front trim piece on the front bumper and align the edges with the masking tape. Install one bracket A and one flange nut on each stud from the trim piece. Note the direction of the brackets. 14. While holding light pressure on the left front trim piece, slowly and carefully remove the adhesive backings. 16. Repeat steps 3 through 15 to install the trim piece on the right side of the bumper. 17. Reinstall the front bumper, and the front bulkhead cover. Installing the Rear Bumper Trim Pieces 4N23081P 18. Remove the two short self-tapping washerscrews, four self-tapping screws, two long selftapping washer-screws, two washer-screws, four clips and five bolts that secure the rear bumper. Slide the rear bumper out to release the two fender clips. Set the bumper on a blanket. SHORT WASHER- S (2) FENDER CLIPS (2) LONG WASHER- S (2) CLIP WASHER- S (2) BOLTS (5) 4N23092P 4 of 6 AII 30482 (0509) 2005 American Honda Motor Co., Inc. - All Rights Reserved.
19. On the inside of the rear bumper, locate the three marks on the left side. Center-punch each of the three marks. The correct marks have brackets ([ ]) next to them. 22. Attach a strip of masking tape to the ends of the adhesive backings shown and peel back 2 to 3 inches from the ends. Fold the ends up and tape them to the front of the trim piece. Remove the remaining adhesive backing. <RIGHT SIDE> CORRECT Do not drill this mark. ADHESIVE BACKING (Remove.) Attach a strip of masking tape to the end and peel back 5 to 6 inches from that end. Fold the ends up and tape them to the front of the trim piece. CENTER- PUNCH LEFT 3 mm DRILL BIT 1-1/8" (28 mm) HOLE SAW 4N23102P Attach a strip of masking tape to the end and peel back 2 to 3 inches from that end. Fold the ends up and tape them to the front of the trim piece. 5420010P 20. While wearing eye protection, drill an 1-1/8" (28 mm) hole through each of the center-punched marks. First drill with a 3 mm bit, and finish with an 1-1/8" (28 mm) hole saw. Remove all burrs from the edges of the holes. Attach a strip of masking tape to the end and peel back 2 to 3 inches from that end. Fold the ends up and tape them to the front of the trim piece. 21. Position the left rear trim piece on the rear bumper and adjust it until it fits snug. Using strips of masking tape, mark the location of the trim piece. LEFT 4N23111P 2005 American Honda Motor Co., Inc. - All Rights Reserved. AII 30482 (0509) 5 of 6
23. Using isopropyl alcohol on a shop towel, clean the area where the trim piece will attach. 25. While holding light pressure on the trim piece, slowly and carefully remove the adhesive backings. FLANGE NUTS (3) Torque to 10 N m (7.3 lb-ft) BRACKETS B (3) FLANGE NUT BRACKET While holding light pressure on the trim piece, slowly and carefully remove the adhesive backings. LEFT LEFT LEFT TRIM PIECE 4N23121P LEFT ATTACHING SURFACE (Clean with Isopropyl alcohol.) 26. Torque the flange nuts to 10 N m (7.3 lb-ft). 27. Repeat steps 19 through 26 to install the trim piece on the right side of the bumper. 28. Reinstall the rear bumper. 29. Remove all of the masking tape. 4N23131P 24. Position the left rear trim piece on the rear bumper, and align it with the masking tape. Install one bracket B and one flange nut over each stud on the trim piece. Note the direction of the brackets. 6 of 6 AII 30482 (0509) 2005 American Honda Motor Co., Inc. - All Rights Reserved.