12v 2 X 21W + 5W Lucas type 8FL with Lucar connectors each 6.39 ex VAT

www.holden.co.uk Flasher Units 6v 36W This is the flasher unit we offer for 6 volt applications. It has 3 Lucar terminals, 36 watts maximum load 080.002 14.88 each 12.40 ex VAT 12v 21W Lucas type FL5 for motorcycles with one flasher lamp each side 35024 13.20 each 11.00 ex VAT 12v 2 X 21W + 5W Lucas type 8FL with Lucar connectors 35048 7.67 each 6.39 ex VAT 12v 3 X 21W Lucas original type 8FL for Lucar connectors 35052 18.00 each 15.00 ex VAT 12v hazard Warning Unit Can be wired to flash all your indicators as a hazard warning 35053 8.06 each 6.72 ex VAT 12v 42W SCreW ConneCtorS Modern version of early type of Lucas flasher unit with screw connections, 42 watts maximum load 35010 11.94 each 9.95 ex VAT 12v 42W lucar ConneCtorS Genuine Lucas flasher unit with Lucar connectors. Maximum load 42 watts 35020 18.00 each 15.00 ex VAT 12v 98W 3-pin This is the equivalent of Lucas SFB162. Operates on 12V and up to 98 watts. Fits into 080.083 socket 080.082 15.35 each 12.79 ex VAT 12v 98W 4-pin This is the equivalent of Lucas SFB163. Operates on 12V and up to 98 watts. Fits into 080.083 socket 080.137 15.35 each 12.79 ex VAT SoCket With ConneCtorS For use with flasher Units 080.082 and 080.137 on left, also relays 080.083 3.42 each 2.85 ex VAT 12v flasher Unit This 12V Flasher unit was fitted to some versions of the MGA and Morris Minor, and other cars 33117/DB10 106.60 each 88.83 ex VAT For latest prices refer to website Split Charge relay for Caravan Enables you to keep your caravan battery charged while you are driving along. 12 volt SRB630 25.94 each 21.62 ex VAT hazard Warning relay Enables you to add hazard warning function to the existing flashers on your car. 12 volt 080.799 9.36 each 7.80 ex VAT 91

Relays +44 (0) 1885 488 488 A relay is an electrical switch which uses low wattage current to open another switch. It is this second switch that carries and switches the high wattage current. This second switch can be normally open, normally closed or offering a changeover facility such as headlamp dip. They are a very useful safety device to have on high wattage circuits on your car. Remember to wire both the low wattage circuit and the high wattage circuit through appropriate fuses. We show here a number of different relays we have available: General purpose relays in a metal case with two fixing holes. Suitable for horn, lamp, alternator field, starter solenoid, accessory and transmission circuits. All 12 volts and 20 amps Contacts Normally open (horn, lights) (shown) SRB111 33.48 each 27.90 ex VAT Normally open, Jaguar XK horn 33135/SB40 46.20 each 38.50 ex VAT Normally closed SRB131 36.31 each 30.26 ex VAT Changeover (main to dip lamps) SRB146 33.00 each 27.50 ex VAT These modern mini relays are very useful and can be used on any classic or vintage car to reduce the load through the existing switches. They can be fitted using the bracket supplied and Lucar connectors or discard the bracket and use Socket 080.083 3.35 each 2.85 ex VAT. Sockets can be clipped together side by side 12v 15 amps normally open Fitted with 15 amp fuse to prevent overloading SD/080.801 8.38 each 6.98 ex VAT 12v 20 amps normally CloSed Circuit opens when energised SD/080.804 8.04 each 6.70 ex VAT 12v 20 amps Changeover Changeover from one circuit to another SD/080.805 8.04 each 6.70 ex VAT 12v 2x15 amps normally open Makes two contacts of 15 amps each S080.806 8.53 each 7.11 ex VAT 12v 2x15 amps normally open Makes two contacts, total load 30 amps 080.807 9.89 each 8.24 ex VAT 12v 30 amps normally open Normally open 080.800 6.30 each 5.25 ex VAT 92 12v 30 amps normally open Fits Ford, Jaguar and others 080.081 6.30 each 5.25 ex VAT 12v 70 amps normally open Heavy duty. Use Lucar connectors 080.802 11.16 each 9.30 ex VAT 12v 180 amps normally open Extra heavy duty relay. Second switch has screw terminals SD/080.803 26.59 each 22.16 ex VAT s correct at March 2014

www.holden.co.uk Control Boxes rf95 Control BoX This early 9 post type control box/regulator type RF95 was introduced just before WWII and continued until the mid 1950s. It incorporated a thermostat for temperature regulation (compensated voltage control) and had external fuses. It became almost universal, being fitted to Allard, Alvis, Armstrong Siddeley, Aston Martin, Austin, Bristol, Daimler Healey, Hillman, H.R.G., Humber, Jaguar, Jensen, Jowett, Lea Francis, MG, Morgan, Morris, Riley, Rover, Singer, Standard, Sunbeam-Talbot, Triumph, Vauxhall, Wolseley plus others. Unavailable for some time, these are our own reproduction: 12 volt RF95 118.80 each 99.00 ex VAT 6 volt RF95/6v 144.00 each 120.00 ex VAT The items above are supplied with a plastic cover that is plain at the top. As an extra we are able to supply a quality reproduction of the original Lucas cover, which has LUCAS and the other markings moulded in 080.107 25.20 each 21.00 ex VAT 6v Control BoX/regUlator Although we are listing this part with the suffix R to indicate that it is a reproduction, the ones we have may be original Lucas. There was also a Lucas Part No. 37097. Size approx 114mm length x 60mm width x 90mm height MCR2/R 36.00 each 30.00 ex VAT Control BoX SCreWS For RB106, RF95, RF96, RF91 etc. Set of 5 080.040 3.48 per set 2.90 ex VAT rb106/ncb100 Control BoX/regUlator 6 volt. Screw fitting 37216 118.80 each 99.00 ex VAT 12 volt. Screw fitting 37182 32.30 each 26.92 ex VAT rb106/ncb100 Control BoX/ regulator 12 volt. Lucar fitting 37290 32.30 each 26.92 ex VAT rb108 Control BoX/regUlator 12 volt. Lucas original RB108 40.80 each 34.00 ex VAT rb340 Control BoX/regUlator 12 volt 22 amp SDNCB130 29.40 each 24.50 ex VAT 12 volt 30 amp SDNCB133 50.40 each 42.00 ex VAT 4tr alternator Control - 4 terminal Quality reproduction of the alternator control for early Lucas 12 volt alternators 15AC/16AC. (Lucas five figure Part Nos included 37586, but Lucas originals no longer manufactured). Fitted to many cars including MGB, MGC, Triumph TR5 etc. Original Equipment Part No. BHA4789 NCB148 49.43 each 41.19 ex VAT For latest prices refer to website 4tr alternator Control 3 terminal Early Lucas 12 volt alternators had this separate regulator Model 4TR and Part No. NCB144. Fitted to Jaguars 420/E Type/Mk 10, Mini and Stag. Genuine Lucas NCB144 38.35 each 31.96 ex VAT 11aC Warning light Control Lucas 11AC alternators have an external relay Lucas Part No. 3AW or 38706 which operates the warning light on the dashboard. If yours fails, new ones have not been available for some time. This is a specially made replacement. Full instructions for fitting and wiring are supplied For NEGATIVE EARTH only 080.808 42.00 each 35.00 ex VAT For POSITIVE EARTH only 080.809 46.80 each 39.00 ex VAT Single phase regulator Fits most English bikes with 12 volt 2 wire alternators (single phase). However, if you have an old 6 volt 3 wire stator you can convert it to 12 volt using this regulator, full instructions are supplied. Your old rectifier and zener diode will not be needed with either 6 or 12 volts. 68 mm x 60 mm x 25 mm tall with two fixing holes 080.961 35.88 each 29.90 ex VAT 93

Glass Fuses +44 (0) 1885 488 488 glass fuses and fuseboxes 4fJ for 2 glass type fuses Lucas fuse box with cover (clips into place) for two glass type fuses. Each end of each fuse carrier has multiple 6.4mm Lucar connectors. Includes provision to store two spare fuses 54038068 18.22 each 15.18 ex VAT Sf6 for 2 glass fuses Lucas fuse box for two glass type fuses. Provision to store two more, retained by clips. Plated screw connections. No cover, but ideal for adding fuses into an existing set up 37132 37.20 each 31.00 ex VAT Sf4 for 4 glass type fuses Lucas fuse box with cover (retained by screw) for four glass type fuses. Each end of each fuse carrier has brass screw connections and there is provision to store two spare fuses. Vintage appearance 54038067 78.46 each 65.38 ex VAT Cover only 385038 33.60 each 28.00 ex VAT 94 7fJ for 4 glass type fuses Lucas fuse box with clip on cover for four glass type fuses. Provision to store two spare fuses. Each end of each fuse carrier has two 6.4mm Lucar connections sideways from the fuse box 37420 23.59 each 19.66 ex VAT glass fuses 7fJ for 4 glass type fuses Lucas fuse box with clip on cover for four glass type fuses. Provision to store two spare fuses. Each end of each fuse carrier has at least two 6.4mm Lucar connections through the base 37416 23.59 each 19.66 ex VAT Rating Colour Part No. Part No. Part No. amps for 3 off for 10 off for 50 off 2 Red on blue CFB102A3 CFB102A10 CFB102A50 5 Red CFB105A3 CFB105A10 CFB105A50 8 Blue on green CFB108A3 CFB108A10 CFB108A50 10 Black on blue CFB110A3 CFB110A10 CFB110A50 15 Light brown CFB115A3 CFB115A10 20 Blue on yellow CFB120A3 CFB120A10 CFB120A50 25 Pink CFB125A3 CFB125A10 CFB125A50 35 White CFB135A3 CFB135A10 CFB135A50 50 Yellow CFB150A3 CFB150A10 CFB150A50 All same price 1.80 for 3 4.74 for 10 11.15 for 50 1.50 ex VAT 3.95 ex VAT 9.29 ex VAT For boxed fuses please refer to 080.404 on next page 7fJ for 4 glass type fuses Lucas fuse box with clip on cover for four glass type fuses. Provision to store two spare fuses. Each end of each fuse carrier has two 6.4mm Lucar connections sideways from the fuse box, two of which are joined by a 'common link' underneath 37521 23.59 each 19.66 ex VAT A different two connections linked 37552 33.53 each 27.94 ex VAT in line fuse holder for a glass fuse Lucas In-line fuse holder for inserting into a wire to protect a new piece of equipment. Useful if you are adding something electrical to your car / CAB389 4.74 each 3.95 ex VAT s correct at March 2014

www.holden.co.uk Rating Colour Part No. for 3 off Part No. for 50 off 5 amps Yellow CFB305A3 CFB305A50 8 amps White CFB308A3 CFB308A50 16 amps Red CFB316A3 CFB316A50 25 amps Pink CFB325A3 CFB325A50 All same price 1.80 for 3 5.59 for 50 1.50 ex VAT 4.66 ex VAT Continental fuses and fuseboxes BoX of glass and Continental fuses (Left) A selection of fuses packed in a plastic box, with clear lid, containing: Glass Fuses: 30 off each 5 amp, 10 amp, 15 amp, 25 amp & 50 amp and 90 off 35 amp. Continental Fuses: 50 off each 5 amp, 8 amp, 16 amp and 24 amp 080.404 32.62 each 27.18 ex VAT Fuses fuseboxes With Clear CoverS, SCreW terminals fuseboxes With BlaCk CoverS, lucar terminals For 12 fuses SD/080.006 20.40 each 17.00 ex VAT For 12 fuses SD/080.659 19.98 each 16.65 ex VAT For 8 fuses SD/080.655 12.20 each 10.17 ex VAT For 8 fuses SD/080.658 11.95 each 9.96 ex VAT For 6 fuses SD/080.007 9.54 each 7.95 ex VAT For 6 fuses SD/080.010 9.20 each 7.67 ex VAT For 4 fuses SD/080.008 7.12 each 5.93 ex VAT For 2 fuses SD/080.656 4.92 each 4.10 ex VAT For 2 fuses SD/080.009 4.92 each 4.10 ex VAT Blade fuses and fuseholders Rating Identification Part No. for 3 ex VAT 3 amps Purple CFB403A3 2.39 for 3 1.99 ex VAT 4 amps Pink CFB404A3 2.39 for 3 1.99 ex VAT 5 amps Orange CFB405A3 2.39 for 3 1.99 ex VAT 7.5 amps Brown CFB407A3 2.39 for 3 1.99 ex VAT 10 amps Red CFB410A3 2.39 for 3 1.99 ex VAT 15 amps Blue CFB415A3 2.39 for 3 1.99 ex VAT 20 amps Yellow CFB420A3 2.39 for 3 1.99 ex VAT 25 amps White CFB425A3 2.39 for 3 1.99 ex VAT 30 amps Green CFB430A3 2.39 for 3 1.99 ex VAT 40 amps Amber CFB440A3 2.39 for 3 1.99 ex VAT BoX of Blade fuses (Left) A selection of blade type fuses packed in a plastic box, with clear lid, containing 40 off each: 5, 7.5, 10, 15, 20, 25, 30 amp fuses, 5 off blade fuse holders. (Enables you to make a blade fuse into an in-line fuse) 080.407 32.62 each 27.18 ex VAT Single fuseholder Takes a standard blade type fuse. These fuse holders link together side by side to any length you like, 3 to 60 amps CAB390 2.52 each 2.10 ex VAT For latest prices refer to website Single fuseholder Takes a standard blade type fuse and has Lucar connections 080.078 1.56 each 1.30 ex VAT multiple fuseholder As on left: 4 Way for four blade fuses (shown) 080.079 4.92 each 4.10 ex VAT 6 Way for six blade fuses 080.080 5.29 each 4.41 ex VAT fuse BoXeS Each fuse has a red LED indicator light next to it that glows when the fuse has blown (4 Way shown) 4 Way for 4 blade fuses 080.962 16.20 each 13.50 ex VAT 6 Way for 6 blade fuses 080.963 20.04 each 16.70 ex VAT 10 Way for 10 blade fuses 080.964 25.20 each 21.00 ex VAT 95

Dynamo +44 (0) 1885 488 488 lucas C40 reconditioned dynamo (Left) If you still prefer to have a dynamo on your car we offer this Lucas C40 fully reconditioned by a specialist Company in England. This is on an exchange basis, please send in your old dynamo with your order, and please remove and retain the pulley LRD100 95.88 each 79.90 ex VAT Alternators 12 volt alternator If you would like to replace your existing 12 volt dynamo or alternator with a lightweight alternator weighing only 2.8 kilos with a power rating of 45 amps, but are concerned that you may not be able to fit it to your particular vehicle then this is the one for you. Uniquely it has a multi-drilled fixing plate which allows you to manoeuvre the unit into any position on the block giving total flexibility in fitting. Diameter of alternator body is approximately 120mm and the length also 120mm. Supplied with a standard V pulley fitted and instructions 081.190 210.00 each 175.00 ex VAT lucas type multi-mount alternator 12v negative earth A replacement alternator designed to be a direct replacement for many of the popular Lucas type units, including models ACR and A127, as fitted to many British classic cars. This unit features a multi position mounting plate to allow both left and right hand fitting. The unit weighs approximately 3.2 kgs and is rated at 50 Amps. An aluminium pulley is supplied already fitted and full wiring instructions are provided 081.191 238.80 each 199.00 ex VAT ConneCtor for above alternators (Left) 3 pin Connector Plug for alternators 081.190 and 081.191 081.294 15.00 each 12.50 ex VAT lucas type adaptor for above alternators (Left) This adaptor will allow you to replace an exisiting Lucas alternator with either 081.190 or 081.191 without making any modification to the existing Lucas style wiring loom 081.295 30.00 each 25.00 ex VAT 96 s correct at March 2014

www.holden.co.uk Dynalites Users of classic cars nowadays want to fit more and more electrical and electronic equipment, radios, CD players, spotlamps and heaters and reach the point where the original dynamo with its output of about 20 amps can t keep up. If you are running with the lights, wipers, heater etc. on it is probable that your Lucas dynamo is struggling to keep the battery properly charged for the next time you want to start the engine. Modern cars overcome this by using an alternator to meet the larger electrical demand. The Dynalite is such an alternator which will give 80% more power (about 40 amps) than a dynamo and the remarkable thing is that it LOOKS JUST LIKE AN ORIGINAL LUCAS DYNAMO thus maintaining the original underbonnet appearance. It even uses original Lucas end castings. It comes with full instructions for fitting, which may involve simple machining to make your pulley fit, and full wiring instructions which are quite simple or you can buy a new Control Box. Dynalites are polarity conscious as indicated below: Replacement for: Part No. each Ex VAT Dynalite replacement for Lucas C39 Dynamo Negative Earth 081.206 402.00 335.00 Dynalite replacement for Lucas C40 Dynamo Negative Earth 081.200 402.00 335.00 Dynalite replacement for Lucas C40 Dynamo Positive Earth 081.210 460.80 384.00 Dynalite replacement for Lucas C40L Dynamo Negative Earth 081.201 402.00 335.00 Dynalite replacement for Lucas C40L Dynamo Positive Earth 081.211 460.80 384.00 Dynalite replacement for Lucas C40T Dynamo Negative Earth 081.205 541.20 451.00 Dynalite replacement for Lucas C40T Dynamo Positive Earth 081.215 600.00 500.00 Dynalite replacement for Lucas C42 Dynamo Negative Earth 081.202 433.20 361.00 Dynalite replacement for Lucas C42 Dynamo Positive Earth 081.212 492.00 410.00 Dynalite replacement for Lucas C45 Dynamo Negative Earth 081.203 424.80 354.00 Dynalite replacement for Lucas C45 Dynamo Positive Earth 081.207 486.00 405.00 ConneCtion BoXeS for dynalites When replacing your Lucas dynamo with a Dynalite you might also like to consider removing your original control box and fitting one of these which is prewired to suit the Dynalite and at the same time ensuring that the dynamo warning light on your dash continues to function normally SCreW fitting Control BoX Replacing RF95 080.970 58.80 each 49.00 ex VAT For latest prices refer to website SCreW fitting Control BoX Replacing RB106 080.971 46.80 each 39.00 ex VAT pulleys & fan Smaller pulleys to run your Dynalite faster for maximum output (aluminium) Narrow for C39/40/42 081.218 44.40 each 37.00 ex VAT Wide for C39/40/42 081.221 44.40 each 37.00 ex VAT For C45 081.219 44.40 each 37.00 ex VAT For C45 with Fan 081.220 90.00 each 75.00 ex VAT Fan for use with C39/40/42 Dynalites and Pullies 081.218 and 080.221, goes behind pulley. 15mm shaft size. Black enamelled steel 081.217 18.00 each 15.00 ex VAT lucar fitting Control BoX Replacing RB106 080.972 46.80 each 39.00 ex VAT fuses Replacement 40 amp fuse for control boxes 080.970 and 080.975 (shown) 080.974 4.32 each 3.60 ex VAT Replacement 40 amp fuse for control boxes 080.971 and 080.972 080.973 4.32 each 3.60 ex VAT dummy rb340 Control BoX for dynalites If you have a positive earth car with this type of control box and are fitting Dynalite Part No. 081.207 to replace a Lucas C45 positive earth dynamo then we recommend that you purchase this Dummy Control Box which is prewired to suit the Dynalite. This control box is available only on EXCHANGE, please send in your old one when you order 080.975 54.00 each 45.00 ex VAT 97

Powerlite Starter Motors +44 (0) 1885 488 488 98 powerlite Starter motors The Company that makes the Dynalites has developed replacements for many original Lucas starters. Their approach has been slightly different in that they sought to offer something much better than the original. The result is a high performance geared motor which positively engages the pinion into the flywheel electrically and produces a huge increase in cranking power to start the engine under all conditions, even with a higher compression ratio. In addition the gearing means it draws less current. It uses aluminium castings and is beautifully made. In developing starter motors for individual applications special attention has been paid to make them easier to install. They are much lighter than the originals Make & Model Part No. each Ex VAT Alvis TD21 081.250 204.25 170.21 Aston Martin DB1, DB2 & DB3 (1 kw) 081.251 183.83 153.19 Aston Martin DB2/4 to DB6 (1.4 kw) 081.252 202.21 168.51 Aston Martin V8 & Jensen V8 081.266 204.25 170.21 Austin Healey 100/4, 100/6, 3000 081.267 183.83 153.19 Austin Healey Sprite Mk I, II, III, IV, MG Midget Mk I, II, III, (Rover) A Series engines of 948, 1098 & 1275 cc (but not Cooper S) 081.253 183.83 153.19 Ford Essex V6 including TVR V6 081.282 202.21 168.51 Ford Pinto OHC (EAO) 081.279 183.83 153.19 Ford Pre-Crossflow & Kent Engines 081.277 183.83 153.19 Ford Crossflow and Pre-Crossflow engines (Slimline model) 081.320 238.80 199.00 Jaguar 4.2 litre straight 6 081.270 194.04 161.70 Jaguar E Type 3.8 & 4.2 litre, 29mm pinion 081.256 194.04 161.70 Jaguar E Type 3.8 litre, 37.5mm pinion 081.255 194.04 161.70 Jaguar XK120, XK140 & XK150 with manual gearbox, 3.4 or 3.8 litres 081.254 194.04 161.70 Land Rover 2.25 & 2.6 litre petrol 081.257 202.21 168.51 Land Rover 2.3 & 2.5 litre diesel 081.283 202.21 168.51 Lotus Elan/Twin Cam (but not Lotus Cortina or Lotus Sunbeam) 081.258 183.83 153.19 MG Midget 1500, Triumph Spitfire 1300 & 1500, Triumph Dolomite 081.259 183.83 153.19 MGA & MGB up to 1968 (inertia type) 081.260 183.83 153.19 MGB Chrome Bumper 1968-75 (pre-engaged type) 081.271 183.83 153.19 MGB 1968 on & MGC (pre-engaged type) 081.261 183.83 153.19 MGB V8, Morgan +8 (Rover V8), Rover V8, Triumph TR8 & TVR (Rover V8) 081.262 234.89 195.74 Mini with Inertia Type Starter 081.272 183.83 153.19 Mini with Pre-engaged Starter 081.273 183.83 153.19 Rolls-Royce/Bentley V8 3-speed 081.268 204.25 170.21 Rolls-Royce/Bentley V8 4-speed 081.269 403.40 336.17 Triumph Dolomite Sprint 081.274 194.04 161.70 Triumph GT6 081.265 183.83 153.19 Triumph Stag 081.276 183.83 153.19 Triumph TR2 & early TR3 081.263 183.83 153.19 Triumph TR3, TR3a (bolt on ring gear), TR4 & TR4a 081.264 183.83 153.19 Triumph TR5 and TR6 081.275 183.83 153.19 powerlite Starter motor ConneCtor For Powerlite Starter Motors that have a built-in solenoid connected to the ignition key or starter button on your car. The connector for this is situated on the side of the starter motor and comprises a 6.4mm Lucar spade terminal. You can connect to this using a standard Straight Lucar Connector (refer to 080.325). However, the proper way to make this connection is to use the two parts supplied under this Part No.. You crimp/solder the connector to the wire and slide it into the cover. (You push the connector into the end opposite to the clip). The resulting assembly is easier to fit into the receptacle on the starter motor and also has a clip which holds it securely in place 081.289 3.00 each 2.50 ex VAT s correct at March 2014

www.holden.co.uk Powerlite Starter Motors powerlite Starter motor adaptor This adaptor allows the main feed terminal to be turned through 90 degrees to allow for a more convenient cable run. It is especially useful where access is limited 081.290 15.00 each 12.50 ex VAT powerlite Cold Start diode For use where there is an extra wire on your old starter motor solenoid to provide a cold start 'boost' to the coil. This is often found on cars with a ballast resistor in the ignition system 081.291 15.00 each 12.50 ex VAT Charging rectifier pos/neg earth For either positive or negative earth. Diagram supplied 080.928 5.70 each 4.75 ex VAT rectifier positive earth Genuine Lucas. Fits late Nortons 54048017 71.88 each 59.90 ex VAT heatsink for zener diodes Triumph original equipment Part No. was 97-2237. Also for BSA's 080.929 27.06 each 22.55 ex VAT heatsink for zener diodes For BSA/Royal Enfield 080.927 49.45 each 41.21 ex VAT BrUSheS For Lucas dynamos Small type 200924 10.80 each 9.00 ex VAT Large type 200737 11.88 each 9.90 ex VAT diode negative Zener diode negative 49589 38.28 each 31.90 ex VAT dynamo Band With Cork insert Fits many Lucas Dynamos, supplied complete with cork insert 19306 9.54 each 7.95 ex VAT Cork Insert only for Dynamo Band 19306 10008 4.50 each 3.75 ex VAT mag-dyno gear Set As shown 462863 83.94 each 69.95 ex VAT reluctor As shown 54400905 9.00 each 7.50 ex VAT Stator Reproduction of Lucas RM19, 3 lead, 11.5 amps, commonly used as 6 volt 47204 95.40 each 79.50 ex VAT Stator Reproduction of Lucas RM21, 2 lead, 10.0 amps 47205 69.00 each 57.50 ex VAT For latest prices refer to website Stator Reproduction of Lucas RM24, 3 lead, 7.0 amps. As fitted to late Triumph T140 47252 90.06 each 75.05 ex VAT rotor 6 pole with welded centre. RM20 with 0.752" centre. This rotor supersedes all other specifications 54202299 94.98 each 79.15 ex VAT 99

Wire +44 (0) 1885 488 488 It is important that correct wire sizes and connectors are used for linking together all the electrical equipment on your car. The wire size for any circuit is determined by a combination of factors, including the length of the wire, the current flowing and the permissible voltage drop. If the wire is too thin it can cause a serious voltage drop from one end of the wire to the other, together with overheating. To ensure reliability, it is most important that correctly rated wires are used for all circuits. When in doubt, always use a thicker wire size, especially for long runs. To provide flexibility for motor vehicle applications the wires we offer have a number of thin strands rather than a single thicker strand. For example, 14/0.30 mm has 14 strands of wire, each strand 0.30 mm diameter. Wires are rated for their current carrying capacity, and colour coded for identification. Most British designed vehicles use colour coding in accordance with a British Standard, and in the table below we have included the coding based on the Standard. To obtain the best results, at each end of each wire the connector should be securely crimped or soldered to the wire conductor, and a protective sleeve should be used wherever possible. In the tables we list the more popular sizes of PVC insulated wire automatic Wire Stripper Strips a variety of wire sizes. In a single action it holds the wire, cuts the covering and strips it. Brilliant! 090.032 30.46 each 25.38 ex VAT 100 Wire 14/0.30 mm 8 amps maximum nominal CroSS SeCtional area 1 SqUare mm Colour From To Part No. per ex VAT Black Earth connections Chassis 080.160 4.18 6 metres 3.48 Black/Yellow Speedo pick up Speedo 080.162 0.60 metre 0.50 Blue/Red Dip switch Headlamp dip beams 080.163 0.60 metre 0.50 Blue/White Dip switch Headlamp main beams 080.164 0.60 metre 0.50 Green Fusebox (via ) 080.175 4.18 6 metres 3.48 Green/Black tank sender unit gauge 080.165 0.60 metre 0.50 Green/Brown Reverse lamp switch Reverse lamp 080.166 0.60 metre 0.50 Green/Purple Stop lamp switch Stop lamps 080.168 0.60 metre 0.50 Green/Red Flasher switch Left hand flasher lamps 080.169 0.60 metre 0.50 Green/White Flasher switch Right hand flasher lamps 080.170 0.60 metre 0.50 Purple/Green Fusebox (battery feed) Hazard flasher 080.172 0.60 metre 0.50 Red switch Sidelamps & numberplate 080.173 4.18 6 metres 3.48 Red/White switch Map light/instrument lighting/panel light switch Panel light switch Panel light 080.174 0.60 metre 0.50 Yellow/Green 080.177 0.60 metre 0.50 Wire 28/0.30 mm 17 amps maximum nominal CroSS SeCtional area 2 SqUare mm Colour From To Part No. per ex VAT Black Earth connections Chassis 080.180 4.18 3.5 metres 3.48 Blue switch Dip switch 080.183 4.18 3.5 metres 3.48 Blue/Red 080.184 0.96 metre 0.80 Blue/White 080.185 0.96 metre 0.80 Blue/Yellow Driving light switch Driving lights 080.186 0.96 metre 0.80 Brown/Blue Control box switch switch Control box 080.187 0.96 metre 0.80 Brown/Yellow Dynamo Control box 080.189 0.96 metre 0.80 Green Fusebox (via ) Wiper motor 080.190 4.18 3.5 metres 3.48 Purple Fusebox (battery feed) 080.191 0.96 metre 0.80 Purple/Black 080.192 0.96 metre 0.80 Purple/Yellow Horn relay Horns 080.193 0.96 metre 0.80 Red 080.194 0.96 metre 0.80 White switch Petrol pump 080.201 0.96 metre 0.80 White/Red 080.200 0.96 metre 0.80 Wire 44/0.30 mm 25 amps maximum nominal CroSS SeCtional area 3 SqUare mm Colour From To Part No. per ex VAT Black Earth Earth 080.312 1.44 metre 1.20 Brown Battery or Solenoid Fuse box or Ammeter 080.313 1.44 metre 1.20 Brown/White Ammeter Control box 080.315 1.44 metre 1.20 s correct at March 2014

www.holden.co.uk pre-insulated ConneCtorS Connectors RED connectors are for use with 14/0.30mm wire, BLUE are for 28/0.30mm wire and YELLOW are for 44/0.30mm wire BoX of ConneCtorS for 14/0.30mm Wire A selection of RED pre-insulated crimp type connectors packed in a plastic box, with clear lid a) 30 Male and 50 female 6.4mm blade connectors b) 25 fully insulated female 6.4mm connectors c) 40 'piggy back' 6.4mm connectors d) 35 4.8mm and 30 2.8mm female connectors e) 40 male and female bullet connectors f) 50 5mm eyelets and 20 quick connectors 080.398 32.62 each 27.18 ex VAT BoX of ConneCtorS for 28/0.30mm Wire A selection of BLUE pre-insulated crimp type connectors packed in a plastic box, with clear lid. a) 50 off each male and female 6.4mm blade connectors b) 50 off each male and female bullet connectors c) 20 off 8mm eyelets 080.397 32.62 each 27.18 ex VAT BoX of ConneCtorS for 14/0.30 & 28/.030mm Wire A selection of RED and BLUE preinsulated crimp type connectors packed in a plastic box, with clear lid. a) 60 blue & 30 red 6.4mm male connectors b) 10 Blue & 25 red fully insulated 6.4mm female connectors c) 10 Blue 'piggy back'6.4mm connectors d) 5 4.8mm and 30 2.8mm red female connectors e) 10 male and 35 female bullet connectors f) 10 6mm and 30 8mm blue eyelets g) 30 red and 10 blue wire joiners and 5 blue quick connectors 080.399 32.62 each 27.18 ex VAT BoX of ConneCtorS for 44/0.30mm Wire A selection of YELLOW pre-insulated crimp type connectors packed in a plastic box, with clear lid. a) 50 female 6.4mm connectors b) 40 fully insulated 6.4mm female connectors c) 40 female 9.5mm connectors d) 40 male and 40 female bullet connectors e) 40 wire joiners f) 40 8.4mm and 40 10.5mm eyelets 080.402 32.62 each 27.18 ex VAT For latest prices refer to website BoX of ConneCtorS for 14/0.50mm, 28/0.30mm and 44/0.30mm Wire A selection of RED, BLUE and YELLOW preinsulated crimp type connectors packed in a plastic box. a) Red female connectors for 2.8mm and 6.4mm Lucars, b) Red male 6.4mm Lucar connectors c) Red male and female bullets and connectors for joining wires d) Blue female for 6.4mm Lucars e) Blue male 6.4mm Lucar connectors f) Blue male and female bullets and connectors for joining wires g) Blue piggy-back for 9.5mm Lucars h) Yellow female connectors for 9.5mm Lucars j) Yellow connectors 080.409 21.84 each 18.20 ex VAT Crimping tools for pre-insulated ConneCtorS (Left) Crimps the three sizes of pre-insulated connectors (RED, BLUE and YELLOW), alnd ignition terminals, and cuts and strips six sizes of wire 090.003 9.06 each 7.55 ex VAT (Right) A rachet type for preinsulated connectors where full crimping pressure must be applied before the connector can be released. Crimps three sizes of pre-insulated connectors (RED, BLUE and YELLOW). This is the tool for professionals and anyone requiring the best possible job 090.005 43.06 each 35.88 ex VAT 101

Connectors +44 (0) 1885 488 488 UninSUlated ConneCtorS For Lucar 6.4mm ( 1 4 ) blade fittings Straight ConneCtor 080.325 5.23 per 50 4.36 ex VAT Or supplied with clear cover 080.135 2.42 per 5 2.02 ex VAT Straight ConneCtor With non-return tag 080.326 4.61 per 50 3.84 ex VAT right angled ConneCtor Supplied with clear cover as shown 080.055 2.42 per 5 2.02 ex VAT ConneCtor 2 Blade Joins two wires or makes a double earth connection. Centre hole 3.2mm diameter 080.328 8.02 per 50 6.68 ex VAT piggy BaCk ConneCtor Enables you to connect 2 wires to 1 feed using Lucar connectors 080.327 11.28 per 50 9.40 ex VAT For Lucar 9.5mm ( 3 8 ) blade fittings Straight ConneCtor 080.329 20.14 per 50 16.78 ex VAT Straight ConneCtor With non-return tag 080.359 27.31 per 50 22.76 ex VAT Crimping tools for UninSUlated ConneCtorS (Left) Crimps three sizes of uninsulated connectors and ignition terminal, and strips and cuts six sizes of wire 090.004 9.83 each 8.19 ex VAT (Right) A rachet type for uninsulated connectors where full crimping pressure must be applied before the terminal can be released. The pressure at which this occurs can be adjusted. The tool the professionals use 090.006 74.64 each 62.20 ex VAT harness ConneCtorS earth ConneCtor One end has a 9.5mm Lucar blade, the other has a 4.7mm diameter hole 080.367 16.34 per 50 13.62 ex VAT Connector for connecting wires within a harness. Each connector comprises two moulded plastic halves with a positive clipping arrangement and pins and sockets for you to wire up ConneCtor 2 Way 080.042 3.18 each 2.65 ex VAT ConneCtor 3 Way 080.043 3.18 each 2.65 ex VAT ConneCtor 4 Way 080.044 3.42 each 2.85 ex VAT 102 ConneCtor 5 Way 080.045 3.54 each 2.95 ex VAT ConneCtor 7 Way 080.047 3.78 each 3.15 ex VAT ConneCtor 9 Way 080.049 4.78 each 3.98 ex VAT s correct at March 2014

www.holden.co.uk BUllet terminals & ConneCtorS Connectors BUllet terminal for Crimping For wire size 9/0.30 (5 amps) S080.265 13.27 for 25 11.06 ex VAT BUllet terminal for Crimping For wire size 14/0.30 (8 amps) 080.266 13.86 for 25 11.55 ex VAT BUllet terminal for Crimping For wire size 28/0.30 (17 amps) 080.267 7.74 for 25 6.45 ex VAT BUllet terminal for Crimping For wire size 44/0.30 (25 amps) 080.268 13.27 for 25 11.06 ex VAT BUllet terminal for Soldering Suitable for wire sizes up to 44/0.30 (25 amps) 080.264 12.14 for 25 10.12 ex VAT earthing Sleeve Requiring neither crimping nor soldering. Just poke the wire through it, fold it over and push the sleeve into the earth clip 555910 5.10 for 25 4.25 ex VAT BUllet ConneCtor for 2 WireS 080.260 8.59 for 25 7.16 ex VAT BUllet ConneCtor for Up to 4 WireS, Common contact 080.261 11.58 per 25 9.65 ex VAT BUllet ConneCtor 5 in 5 out Insulated from each other 080.263 13.50 each 11.25 ex VAT BUllet ConneCtor 5 pairs in & out You can fit up to five pairs of wires/bullets insulated from each other. This gives you a multiple connection point. For example, you can have five feeds in and for each of these you can have one or two wires out. A neat way of wiring the lights at the front or rear of a car 080.077 8.34 each 6.95 ex VAT Crimping tools for BUllet terminals For bullet terminals 080.265, 080.266, 080.267 & 080.268 090.002 39.84 each 33.20 ex VAT Crimping tools for BUllet terminals Gives a hexagonal professional finish 091.090 57.96 each 48.30 ex VAT Snip Snap tool for BUllet terminals For inserting & closing solder or crimp bullets into connector tubes shown below. Without this tool it is quite difficult to do this 090.001 34.18 each 28.48 ex VAT BoX of BUlletS & ConneCtorS Packed in a plastic box with a clear lid. 50 off each 080.264, 080.266 and 080.267, 25 off 080.260, 080.261 & 080.263. Ideal for storing these parts in your workshop so that you can find them easily when needed 080.396 58.85 each 49.04 ex VAT For latest prices refer to website Soldering iron kit Comprising iron, straight tip, angled tip, tube of solder, stand, sponge and tweezers. 230V mains plug supplied /094.836 18.91 each 15.76 ex VAT Flux Cored Solder Grade K60/40 tin/lead. Manufactured to BS219K Specification. 20g tube /094.856 4.50 each 3.75 ex VAT 103

Eyelets +44 (0) 1885 488 488 eyelet Hole size 3.8mm dia. For wire up to 3mm dia. 080.316 19.18 per 50 15.98 ex VAT eyelet Hole size 4.8mm diar. For wire up to 5mm dia. 080.317 15.79 per 50 13.16 ex VAT eyelet Hole size 6.3mm dia. For wire up to 6mm dia. 080.318 18.82 per 50 15.68 ex VAT eyelet Hole size 6.5mm dia. For wire up to 7mm dia. 080.319 25.18 per 50 20.98 ex VAT 104 eyelet Hole size 8mm dia. For wire up to 5mm dia. 080.322 34.15 per 50 28.46 ex VAT 2-Way JUnCtion BoX 2-way with cover and screw 78265 10.92 each 9.10 ex VAT 8-Way JUnCtion BoX 8-way with cover as shown 080.004 24.89 each 20.74 ex VAT eyelet Hole size 9.8mm dia. For wire up to 5mm dia. 080.323 29.45 per 50 24.54 ex VAT Junction Boxes Butt Connectors eyelet Hole size 13.5mm dia. For wire up to 5mm dia. 080.324 25.94 per 50 21.62 ex VAT 4-Way JUnCtion BoX Quality reproduction of Lucas 4-way with cover and screw 78264 18.61 each 15.51 ex VAT multi-pin ConneCtor Not really a junction box, but a useful way of providing a point of disconnection in your wiring. Moulded from black plastic with a black rubber boot. The pins and sockets are included for you to wire up the number you need 7 pin (Left above) 080.013 11.88 each 9.90 ex VAT 9 pin (Right above) 080.019 13.20 each 11.00 ex VAT heatshrink BUtt ConneCtorS (Left) The stripped wires are inserted into the connector and crimped together, heat is applied with a hot air gun, lighter or match and the adhesive lined heatshrink reduces to form a seal RED for 14/0.30mm wires 080.678 6.00 pkt 10 5.00 ex VAT BLUE for 28/0.30mm wires 080.679 6.24 pkt 10 5.20 ex VAT With the addition of solder to complete the connection RED for 14/0.30mm wires (shown) 080.606 8.54 pkt 10 7.12 ex VAT BLUE for 28/0.30mm wires 080.607 8.54 pkt 10 7.12 ex VAT BoX of assorted eyelets Insulated, 10 sizes 080.410 18.66 per 50 15.55 ex VAT 6-Way JUnCtion BoX Quality reproduction of Lucas 6-way with cover and screw 78266 17.44 each 14.53 ex VAT 6-Way Cover and SCreW Plastic cover for Lucas 6- way Junction Boxes. Genuine Lucas 770032 10.80 each 9.00 ex VAT Hot Gun hot air gun - 230 volt The heat setting of this gun can be varied between 50 C and 600 C with an LED heat display. Supplied complete with four nozzles, hook, concentrator and scraper. Use it for heatshrinking our sleeving, paint stripping and thawing pipes 094.019 89.57 each 74.64 ex VAT s correct at March 2014

www.holden.co.uk Sold by the metre Sold by the metre Sleeving Sold by the metre BlaCk pvc Sleeving Suitable for the bundling of wires and protection against damage. Resistant to petrol, oil, water and temperature up to 70 C Inner dia Part No per metre ex VAT 4mm 080.560 0.72 0.60 5mm 080.561 0.72 0.60 6mm 080.562 0.72 0.60 8mm 080.563 0.72 0.60 10mm 080.564 0.72 0.60 12mm 080.565 0.90 0.75 14mm 080.566 0.90 0.75 16mm 080.567 0.90 0.75 Sold by the metre BlaCk nylon ConvolUted Sleeving Suitable for bundling of wires and protection against abrasion. Continuous operating temperature from -40 C to 120 C with short excursions up to 155 C. Resistant to petrol oil and water. Dimensions in mm Outer dia Inner dia Part No per metre ex VAT 9.9 6.8 080.660 1.16 0.97 14 10.5 080.661 1.46 1.22 15.5 11.5 080.662 1.64 1.37 17.3 12.6 080.663 1.99 1.66 21 16.5 080.664 2.14 1.78 24 19.5 080.665 2.74 2.28 28 23.5 080.666 3.48 2.90 Sold by the metre Split ConvolUted Sleeving The specification for this split convoluted sleeving is the same as the non-split sleeving above. However, this product has a continuous split running along its length for easy application. Dimensions in mm Outer dia Inner dia Part No per metre ex VAT 9.9 6.8 080.670 1.31 1.09 14 10.5 080.671 1.46 1.22 15.5 11.5 080.672 1.64 1.37 17.3 12.6 080.673 1.99 1.66 21 16.5 080.674 2.14 1.78 24 19.5 080.675 2.74 2.28 28 23.5 080.676 3.48 2.90 Sold by the metre Spiral Binding Provides a neat and quick method of protecting harnesses and wiring looms against abrasion. Once fitted it can be constantly adjusted & reused. Made from black polythene, OK. from -60 C to 85 C. Dimensions in mm Outer Inner dia dia Part No per metre ex VAT 6.4 4.4 080.608 0.90 0.75 12.7 9.0 080.609 1.52 1.27 Braided Sleeving Designed to help you tidy up your wiring. 8mm diameter, expands to 17mm 080.033 4.79 per metre 3.99 ex VAT red heatshrink Sleeving Inner dia Part No per metre ex VAT 3.2mm 080.583 3.54 2.95 4.8mm 080.584 3.54 2.95 6.4mm 080.585 3.54 2.95 9.5mm 080.586 3.54 2.95 12.7mm 080.587 3.54 2.95 19.1mm 080.588 5.72 4.77 Sold in 1.22 metre lengths Sold by the metre BlaCk heatshrink Sleeving Inner dia Part No per metre ex VAT 2.4mm 080.572 2.34 1.95 3.2mm 080.573 2.34 1.95 4.8mm 080.574 2.34 1.95 6.4mm 080.575 2.34 1.95 9.5mm 080.576 2.34 1.95 12.7mm 080.577 2.34 1.95 19.1mm 080.578 5.72 4.77 25.4mm 080.579 6.60 5.50 38.1mm 080.580 12.76 10.63 For latest prices refer to website heatshrink Sleeving BoX Flexible polyolefin heatshrink sleeving is used for bundling, marking and protecting ends of wires. This sleeving is very nice to use. You cut it to length and slip it over the wire(s) and then heat it to 120 C whereupon it shrinks to up to half its diameter and grips the wire securely. Colour black, but some sizes are also available in red. This is the material to use to create a very professional finish with reliability. 080.589 28.56 each 23.80 ex VAT BlaCk heatshrink Sleeving With an adhesive lining Formulated to melt at 110 C and close around the components by the shrinking action of the sleeve. Shrink ratio 3 to 1 Inner dia before heating Part No per length ex VAT 3.2mm 080.600 8.30 6.92 4.8mm 080.601 8.59 7.16 6.4mm 080.602 9.30 7.75 9.5mm 080.603 10.02 8.35 12.7mm 080.604 10.74 8.95 19.1mm 080.605 18.25 15.21 105

Terminal Covers +44 (0) 1885 488 488 Exposed live terminals should always be covered, particularly those for the starter and its solenoid. If you drop a spanner and it shorts a live terminal the resulting spark could start a fire. Many cars have been lost like this terminal Cover Terminal end fits over diameter of 11mm and will accommodate a cable of 5mm diameter. Material is neoprene 080.287 2.94 each 2.45 ex VAT terminal Cover Terminal end fits over diameter of 14.6mm and will accommodate a cable of 11mm diameter. PVC SD/080.288 1.57 each 1.31 ex VAT terminal Cover Terminal end fits over diameter of 13mm. The cable end is an oval shape 15mm x 10mm across. Neoprene SD/080.290 4.18 each 3.48 ex VAT terminal Cover Terminal end fits over diameter of 11mm and will accommodate a cable of 6mm diameter SD/080.305 1.80 each 1.50 ex VAT Tapes terminal Cover Terminal end fits over diameter of 15mm and will accommodate a cable of 7.5mm diameter SD/080.306 2.22 each 1.85 ex VAT terminal Cover Terminal end fits over diameter of 15mm and will accommodate a cable of 9mm diameter SD/080.307 2.22 each 1.85 ex VAT BondaleC tape Non adhesive tape used for wrapping wiring harnesses. 19mm wide x 33 metres long. The great advantage of this type of tape is that you can undo it BlaCk /080.031 8.08 each 6.73 ex VAT BroWn 080.036 4.92 each 4.10 ex VAT Self amalgamating This tape fuses together to form a watertight outer insulation around wires. 25mm wide x 3 metres long 080.032 13.42 each 11.18 ex VAT pvc adhesive tape - BlaCk 19mm wide x 4.5 metres long 080.641 1.00 each 0.83 ex VAT pvc adhesive tape - red 19mm wide x 4.5 metres long 080.645 1.31 each 1.09 ex VAT pvc adhesive tape - BlUe 19mm wide x 20 metres long 080.642 1.08 each 0.90 ex VAT 106 pvc adhesive tape - green 19mm wide x 20 metres long 080.644 1.19 each 0.99 ex VAT pvc adhesive tape - White 19mm wide x 20 metres long 080.647 1.19 each 0.99 ex VAT pvc adhesive tape - yellow 19mm wide x 20 metres long 080.648 1.19 each 0.99 ex VAT s correct at March 2014

www.holden.co.uk Cable Clips & Cable Ties Max Cable dia plastic CaBle ClipS Dimensions in mm Fixing Hole dia Part No. for 25 ex VAT 7.5 4 080.278 5.94 4.95 9.5 5 080.279 5.94 4.95 12.7-15.9 10 080.280 8.42 7.02 19.1 5 080.363 10.20 8.50 28.5 5 080.364 10.92 9.10 Maximum Cable dia Steel p ClipS Rubber covering Part No. zinc plated Steel CaBle Clip Dimensions in mm Max Cable dia Fixing Hole dia each ex VAT 32mm 080.365 2.40 2.00 40mm 080.366 3.12 2.60 Part No. for 10 for 25 ex VAT 6 5.5 080.887 11.87 9.89 8 5 080.271 11.04 9.20 9.5 5 080.272 11.04 9.20 9.5 7 080.273 14.70 12.25 12.7 5 080.275 17.81 14.84 12.7 10 080.274 14.33 11.94 15.9 5 080.276 20.58 17.15 15.9 10 080.277 16.26 13.55 19 7 080.888 15.60 13.00 CaBle ties Dimensions in mm Width Length Colour Features Part No. per ex VAT 2.5 75 Black 080.069 1.68 10 1.40 3.0 95 White With a writing tag 080.068 1.25 10 1.04 3.0 100 White 080.075 4.92 100 4.10 4.8 146 Black 080.070 2.62 10 2.18 4.8 160 Black With a fixing eye 080.071 3.55 10 2.96 5.0 195 White With a writing tag 080.067 1.63 10 1.36 6.0 210 Black 080.408 6.90 10 5.75 7.6 140 Black Releasable type 080.072 3.96 10 3.30 7.6 250 Black Releasable type 080.073 7.57 25 6.31 A selection of black cable ties, 25 each of 100mm, 165mm, 190mm and 280mm long, in a neat cardboard dispenser you can hang on a nail and always know where to find them (shown in picture) 080.405 6.48 per card 5.40 ex VAT StainleSS Steel p Clip With rubber inserts, for all sizes fixing hole size is 6.5mm. Maximum Cable dia Part No. each ex VAT 5mm 080.110 1.43 1.19 6mm 080.111 1.45 1.21 8mm 080.112 1.49 1.24 10mm 080.113 1.54 1.28 13mm 080.114 1.58 1.32 16mm 080.115 1.67 1.39 21mm 080.116 1.76 1.47 25mm 080.117 1.96 1.63 Less 15% on quantities of 10+ BraSS CaBle Clip Will take 5mm cable. Fixing hole size is 3.2mm diameter. 080.886 5.52 for 10 4.60 ex VAT rubber ferrule Can be used with cable clips 080.274 and 080.275 and any of our battery cables 080.000, 080.027 and 080.028 or with cable bunches up to 10 mm diameter. Has a split, so that you can put it round an existing cable 080.310 2.10 each 1.75 ex VAT mounting Cradle Self adhesive mounting cradle for use with cable ties up to 8mm wide. Size 28mm x 28mm 080.074 7.81 per 25 6.51 ex VAT For latest prices refer to website 107

Grommets +44 (0) 1885 488 488 External dia Hole in Panel pvc & rubber grommets Internal dia Dimensions in mm Thickness Material Part No. per ex VAT 14.28 9.35 6.35 6.35 PVC 080.293 4.98 25 4.15 15.87 11.11 7.93 6.35 PVC 080.294 10.19 25 8.49 19.05 12.70 9.53 6.35 PVC 080.295 12.37 25 10.31 25.40 12.70 6.35 9.35 Rubber 080.296 9.47 25 7.89 34.93 19.05 12.70 11.11 PVC 080.297 11.46 25 9.55 41.28 25.40 19.05 11.11 Rubber 080.298 16.84 25 14.03 47.93 31.75 25.40 11.11 PVC 080.299 14.28 25 11.90 34 26 5 8.5 Rubber 080.084 1.24 each 1.03 41 32 4 10 Rubber 080.085 1.34 each 1.12 56.50 42 13 9 Rubber 080.688 1.80 each 1.50 pvc Blanking grommets Hole in Panel Dimensions in mm For panel thickness 1.6mm Part No. per ex VAT 8 080.831 3.25 25 2.71 10 080.832 3.46 25 2.88 12.5 080.833 4.07 25 3.39 16 080.834 4.34 25 3.62 19 080.835 6.38 25 5.32 32 080.856 4.50 10 3.75 grommet for headlamp ShellS (Left) As used on motorcycle headlamps to allow the wiring to pass through the shell. Fits hole 38mm diameter. Hole in centre for the wire is 12.5mm. A useful grommet which can also be used on cars 010.541 2.29 each 1.91 ex VAT grommets Box of assorted wiring grommets Moulded in PVC. Contains the following sizes, hole required in panel first, then hole in centre for wiring: 6 x 4mm, 8 x 5mm, 10 x 8mm, 11 x 8mm, 12.5 x 10mm, 17.5 x 12.5mm and 19 x 12.5mm SD/080.703 27.24 each 22.70 ex VAT Blanking grommets Box of assorted blanking grommets Moulded in PVC. Contains grommets to blank off holes of the following sizes: 8mm, 10mm, 12.5mm, 16mm, 19mm, 25mm and 32mm 080.704 27.24 each 22.70 ex VAT & Blanking grommets (Left) Assortment of 240 wiring and blanking grommets in a box. grommets 3 8" x 1 4", 1 2" x 5 16", 1 2 x 3 8", 9 16" x 7 16", 11 16" x 1 2" and 3 4" x 1 2". Blanking grommets 5 16", 3 8", 1 2", 5 8", 3 4" and 7 8" 080.687 23.94 each 19.95 ex VAT 108 s correct at March 2014

www.holden.co.uk Battery Cables & Covers Battery CaBle PVC insulated cable from universal battery terminal to an eyelet with 8mm diameter hole. 266 strands x 0.3mm, capable of carrying 135 amps Length Part No. each ex VAT 225mm 080.388 11.64 9.70 300mm 080.340 10.78 8.98 375mm 080.389 11.21 9.34 450mm 080.341 13.18 10.98 600mm 080.342 12.50 10.42 Battery CaBle PVC insulated cable from universal battery terminal to another universal battery terminal. 266 strands x 0.3mm, capable of carrying 135 amps Length Part No. each ex VAT 225mm 080.391 15.13 12.61 300mm 080.392 15.58 12.98 375mm 080.393 16.01 13.34 450mm 080.394 16.45 13.71 Battery CaBle PVC insulated cable from eyelet to eyelet, both with 8mm diameter hole. 37 strands x 0.9mm, capable of carrying 170 amps Length Part No. each ex VAT 300mm 080.368 7.42 6.18 450mm 080.369 8.69 7.24 600mm 080.370 9.22 7.68 Battery CaBle If you have reason to make up your own battery cables we offer genuine LUCAS PVC insulated black battery cable 170 amps maximum 080.000 17.26 per metre 14.38 ex VAT Battery CaBle If you have a convoluted run for your battery cable we have this battery cable made up of 196 separate strands which gives it excellent flexibility for a cable 9.8mm in overall diameter. 170 amps maximum current rating Black SD/080.027 8.98 per metre 7.48 ex VAT Red SD/080.028 8.98 per metre 7.48 ex VAT Battery Clamp Positive battery clamp for making up your own battery cable. Has two screws for clamping to the cable 080.022 4.04 each 3.37 ex VAT Battery Clamp Negative battery clamp for making up your own battery cable. Has two screws for clamping to the cable 080.023 4.04 each 3.37 ex VAT eyelet Battery cable eyelet, for 10mm diameter stud 080.284 0.90 each 0.75 ex VAT eyelet Battery cable eyelet, for 10mm diameter stud 080.283 1.63 each 1.36 ex VAT right hand Battery terminal Cover Adds a neat finishing touch to your battery installation but they are also a safety feature Black ( ) 080.301 1.42 each 1.18 ex VAT Red ( + ) 080.302 1.42 each 1.18 ex VAT For latest prices refer to website left hand Battery terminal Cover Adds a neat finishing touch to your battery installation but they are also a safety feature Black ( ) 080.303 1.42 each 1.18 ex VAT Red ( + ) 080.304 1.42 each 1.18 ex VAT either hand Battery terminal Cover. Adds a neat finishing touch to your battery installation but they are also a safety feature 080.291 4.09 each 3.41 ex VAT 109

Earthing Cables +44 (0) 1885 488 488 earthing CaBle Universal battery clamp, 10mm eyelet, flat cross-section, max load 148 amps (24mm x 8mm x 0.3mm tinned copper) Length Part No. each ex VAT 150mm 080.347 7.00 5.83 225mm 080.348 7.80 6.50 300mm 080.349 8.59 7.16 375mm 080.350 9.38 7.82 450mm 080.351 10.18 8.48 600mm 080.352 10.98 9.15 With Positive Battery Clamp: 230mm 54950210 6.23 5.19 earthing CaBle Universal battery clamp, 10mm eyelet, round cross-section, max load 130 amps (16 x 32 x 0.3mm tinned copper ) Length Part No. each ex VAT 150mm 080.353 8.92 7.43 225mm 080.354 14.09 11.74 300mm 080.355 16.06 13.38 375mm 080.356 18.02 15.02 450mm 080.357 20.00 16.67 525mm 080.358 23.95 19.96 earthing CaBle Uninsulated heavy duty cable for earthing components to body or chassis, 9.5mm eyelets both ends, 13mm diameter round cross section (24 x 9 x 0.3mm tinned copper) Length Part No. each ex VAT 150mm 080.383 6.72 5.60 225mm 080.376 8.23 6.86 300mm 080.384 9.79 8.16 375mm 080.385 11.70 9.75 450mm 080.386 13.56 11.30 525mm 080.387 15.41 12.84 earthing CaBle Uninsulated cable for earthing components to body or chassis, 8mm eyelets both ends, 10mm diameter round cross section (24 x 9 x 0.3mm tinned copper) Length Part No. each ex VAT 125mm 080.380 5.30 4.42 225mm 080.377 7.60 6.33 300mm 080.381 6.78 5.65 375mm 080.382 7.49 6.24 450mm 080.378 8.56 7.13 525mm 080.379 9.61 8.01 110 s correct at March 2014

www.holden.co.uk Cigar Lighters Cigar lighter Standard model, with no illumination 090.325 22.70 each 18.92 ex VAT Cigar lighter Standard model, illuminated 090.326 26.18 each 21.82 ex VAT Cigar lighter With chrome knob, but no illumination 090.850 38.64 each 32.20 ex VAT Cigar lighter With chrome knob, and illumination 090.851 41.93 each 34.94 ex VAT pop out Unit Black 090.327 14.39 each 11.99 ex VAT pop out Unit Chrome 090.852 30.55 each 25.46 ex VAT knob Chrome knob 090.853 16.63 each 13.86 ex VAT plug and SoCketS kit Comprises Plug and a pair of Sockets, which were formerly stocked by us as CAB185 and CAB189. For 12v inspection lamp or similar. It should be noted that the two pins are the same diameter and are not suitable for polarity conscious equipment, nor will this plug fit cars already fitted with sockets of different sizes. Also, please note that the sockets need to be mounted in a non-conducting dashboard or panel where they require two 6.5mm diameter holes 080.041 27.60 each 23.00 ex VAT BraCket Enabling you to fit any of the above under the dash or similar 090.849 3.83 each 3.19 ex VAT Plugs & Sockets 'flying' SoCket Use with the plug in Kit 080.041 to make up an extension lead for your 12 volt inspection lamp 770419 12.38 each 10.32 ex VAT plug and SoCket With Cover For 12 volt inspection lamp or other equipment or charging. Requires 19mm dia hole in dashboard 080.136 19.18 each 15.98 ex VAT Small plug and SoCket A nice small plug and socket for 6V or 12V. The socket requires a 12mm hole in the dashboard and the top of the plug is only 25mm diameter 080.076 4.68 each 3.90 ex VAT Cigar lighter/din plug Can be used with a standard cigar lighter socket or a DIN plug. Inside it has two terminals, and a fuse. To convert it to a DIN plug you turn and remove the red part on the end. We supply it with two ring terminals to assist with wiring it up 080.158 7.32 each 6.10 ex VAT BlaCk plug Maximum load 5 amps at 12V. Use with 080.650 080.651 7.14 each 5.95 ex VAT For latest prices refer to website red plug Maximum load 5 amps at 12V. Use with 080.650 080.652 7.14 each 5.95 ex VAT locking plug Max load 5 amps at 12V. Ferrule screws on to socket 080.650 to stop it falling out. Black only 080.653 9.54 each 7.95 ex VAT Small SoCket Suitable for metal panels. Requires 8mm diameter hole 080.650 8.40 each 7.00 ex VAT 111

Batteries +44 (0) 1885 488 488 traditional rubber CaSed BatterieS As used on vintage/classic cars and motorcycles Volts Type Length Width Height Part No. each ex VAT 12 242 307 171 222 080.935 203.40 169.50 12 279 490 108 222 080.936 210.00 175.00 12 291 251 165 224 080.937 186.48 155.40 6 404 201 170 190 080.939 141.60 118.00 6 421 170 175 230 080.950 88.80 74.00 6 501 227 180 215 080.951 136.08 113.40 For the UK this battery is supplied to your door in dry condition with the acid in a container ready for you to fill. Instructions supplied. There is a special delivery charge for this of 14.40 12.00 ex VAT. For overseas please phone our order line +44 (0) 1885 488 488 Battery anti-corrode (Left) A gel that kills and prevents battery corrosion. The best way to use it is to undo the battery clamp, clean everything up and smear this gel all over the clamp and the battery post to prevent future corrosion. Also smear it over any adjacent metalwork. 20ml tube 080.014 6.30 each 5.25 ex VAT 112 lucas Battery labels A set of three LUCAS adhesive battery labels as shown Top 133 x 57mm Middle 120 x 60mm Bottom 106 x 33mm. 080.155 8.64 each 7.20 ex VAT lucas Battery label It is not always possible to get a battery of a make that would have been originally fitted to your classic car, but you can get this LUCAS adhesive battery label to dress up your (modern) battery 090.708 3.24 each 2.70 ex VAT lucas Battery panel On some cars the battery is very visible when you raise the bonnet (hood) and modern batteries look out of place. You can redeem this situation by using this moulded plastic panel with the Lucas lion logo, by sticking it onto the side of your battery 090.828 18.00 each 15.00 ex VAT lucas king of the road Adhesive label as fitted to Lucas rubber case batteries. 87mm dia. 080.942 3.24 each 2.70 ex VAT s correct at March 2014

www.holden.co.uk Battery Battery BoX - BlaCk This battery box is moulded from ABS and supplied complete with lid and quick release fasteners, internal dimensions are length 260mm x width 180mm x depth 230mm. The manufacturers call this 'carbon look' 080.105 113.22 94.35 ex VAT Battery BoX - red This battery box is moulded from ABS and supplied complete with lid and quick release fasteners. Internal dimensions are length 260mm x width 180mm x depth 230mm 080.106 102.37 85.31 ex VAT Battery mat Goes underneath the battery to assist in overcoming the problem of rusting of steel in the vicinity of the battery. Any acid seepage from the vents which is washed down the battery sides is neutralised SD/090.479 5.92 each 4.93 ex VAT lucar fitting 76mm long with a 32mm jaw opening and a 6.4mm lucar connection for the lead. Maximum recommended load is 25 amps. Plated steel 080.016 2.21 each 1.84 ex VAT SCreW fitting 76mm long with a 32mm jaw opening and a screw connection for the lead. Maximum recommended load is 25 amps. Plated steel 080.015 1.46 each 1.22 ex VAT SCreW fitting 102mm long with a 50mm jaw opening and a screw connection for the lead. Maximum recommended load is 50 amps. Plated steel 080.017 1.57 each 1.31 ex VAT rubber Battery tray BSA / Triumph original equipment part numbers 69-4577/82-8091.148mm x 90mm 080.934 3.72 each 3.10 ex VAT As shown Wd Battery lid 080.920 13.20 each 11.00 ex VAT Battery WeBBing Strap BSa Webbing Strap for battery on BSA 080.925 63.36 each 52.80 ex VAT For latest prices refer to website Battery retainer BSa Three-piece complete with trunnions. BSA A7/A10 Original equipment Part No. 42-4502 080.921 21.00 each 17.50 ex VAT 113

Battery Clamps +44 (0) 1885 488 488 Battery Clamp Black coated steel clamp, fits MG Midget and Austin Healey Sprite up to 1965. Hexagon nut fixing. Distance between holes 340mm. Length of J bolts approx 102mm. Original Equipment Part No. AHA6934K 080.982 7.92 each 6.60 ex VAT Battery Clamp Steel clamp, fits MG Midget and Austin Healey Sprite after 1965. Hexagon nut fixing. Distance between holes 268mm. Length of J bolts approx 102mm 080.983 8.40 each 7.00 ex VAT Battery Clamp Stainless steel clamps, fits MGA & MGB with two 6V batteries. Set contains parts to secure the two batteries. Hexagon nut fixing 080.838 16.90 each 14.08 ex VAT As above, but for just one battery 080.980 6.60 each 5.50 ex VAT Battery Clamp Black coated steel clamp, fits MGB with 12 volt battery. Hexagon nut fixing. Distance between holes 268mm. Length of J bolts 240mm 080.981 8.64 each 7.20 ex VAT Battery Clamp Black coated steel clamp, fits Morris Minor. Wingnut fixing. Distance between holes 340mm. Length of J bolts 185mm, supplied with special collars and spring washers 080.984 10.20 each 8.50 ex VAT Battery Clamp Black coated steel clamp, fits Triumph Spitfire. Wingnut fixing. Distance between holes 268mm. Length of J bolts 130mm 080.985 6.60 each 5.50 ex VAT Battery Clamp Stainless steel clamp, fits Triumph Stag. Wingnut fixing. Special cranked clamp to suit car and J bolts in two lengths also to fit car 080.986 25.20 each 21.00 ex VAT Battery Clamp Black coated steel clamp, fits Triumph TR3/4/4A/250. Wingnut fixing. Distance between holes 340mm. Length of J bolts 150mm 080.987 10.20 each 8.50 ex VAT Battery Clamp Black coated steel clamp, fits Triumph TR5/6. Wingnut fixing. Distance between holes 330mm. Length of J bolts 210mm 080.988 9.00 each 7.50 ex VAT Battery Clamp A stainless steel clamp, fits Triumph TR6/TR7. Hexagon nut fixing. Distance between holes 268mm. Length of J bolts 240mm 080.839 20.34 each 16.95 ex VAT Battery Clamp Black coated steel clamp, fits Triumph TR7. Hexagon nut fixing. Distance between holes 268mm. Length of J bolts 210mm 080.989 9.00 each 7.50 ex VAT Battery Clamp UniverSal A galvanised mild steel clamp, fits batteries up to 335mm long, Has butterfly wing nut fixing. Can be cut to size. SD/080.029 5.75 each 4.79 ex VAT 114 s correct at March 2014

www.holden.co.uk Aerials & Speakers 3 SeCtion Wing mounting aerial Incorporates a strong spring at its mounting end. Closed 550mm, extended 1250mm. Cable 1300mm long 091.912 25.70 each 21.42 ex VAT 4 SeCtion Wing mounting aerial Can be pushed manually into the wing and locked. Closed 40mm, extended 780mm. Cable 1400mm long. Clearance required underneath 285mm 091.913 12.07 each 10.06 ex VAT 4 SeCtion Wing mounting aerial Can be pushed manually into the wing and locked. Closed 10mm, extended 970mm. Cable 1200mm long. Clearance required underneath 300mm 091.908 14.83 each 12.36 ex VAT electric aerial Wing mounting 12V aerial which is retracted electrically into the wing. Extended 1000mm. Cable is 1200mm long. Clearance required underneath 315mm. Fully automatic, needs output from radio 091.914 110.47 each 92.06 ex VAT 2 SeCtion roof mounting aerial Has black plastic base and built in spring to ward off damage 091.919 20.52 each 17.10 ex VAT dual mount aerial For use on vintage style cars. Install by means of the two adjustable mounting bases, normally at the side of the car just in front of the door. Works with all vintage and modern AM and FM radios & stereos. Looks good too! 091.907 30.00 each 25.00 ex VAT aerial extension lead 600mm All our aerials come with a length of lead already fitted, but if you need to extend this then we offer this extension lead 600mm long SD/091.915 5.64 each 4.70 ex VAT aerial extension lead 3 metres All our aerials come with a length of lead already fitted, but if you need to extend this then we offer this extension lead 3 metres long SD/091.916 6.38 each 5.32 ex VAT For latest prices refer to website loudspeaker 30 WattS - 100mm (Left) Complete in a pod. Output 30 watts. 100mm diameter 091.917 27.46 each 22.88 ex VAT loudspeaker 30 WattS - 130mm (Right) Complete in a pod. Output 30 watts. 130mm diameter 091.918 31.39 each 26.16 ex VAT 115

Vintage Horns +44 (0) 1885 488 488 BUgle horn Chromed metal body with rubber bulb 080.917 11.70 each 9.75 ex VAT horn BUlB, reed & BraSS tubing Comprises a large bulb horn (080.219), reed, adaptors and polished brass flexible tubing 610mm long (24 in) with mounting bracket 080.467 144.34 per half metre 120.28 ex VAT flexible BraSS tubing Brass 1 2" (12.7mm) internal dia. Sold by the half metre 080.466 36.19 per half metre 30.16 ex VAT horn BUlB (Left) With brass ferrule. 17mm internal diameter 080.218 21.10 each 17.58 ex VAT horn BUlB (Right) With brass ferrule. 18mm internal diameter 080.219 23.12 each 19.27 ex VAT SpareS for lucas horns horn trumpet r-r type With the large grill, as used by Rolls-Royce. Chromed 080.640 84.00 each 70.00 ex VAT 6 volt Horns horn Cover Chromed. If yours is dented, here is a replacement 080.240 70.56 each 58.80 ex VAT BraCket For Lucas Horns 690617 22.91 each 19.09 ex VAT BraCket The two horn mounting holes measure 102mm centre to centre and the two holes at the base are at 25.4mm centres 701639 14.04 each 11.70 ex VAT 116 lucas altette horn Reproduction of the 6 volt Lucas 'Altette' chrome and black horn 080.237/6V 171.44 each 142.87 ex VAT parts kit for altette horn Comprises chrome front ring and six chromed dome nuts for the periphery, a chromed dome nut and locknut for the centre D/080.638 23.94 each 19.95 ex VAT original lucas 9h horn 6 volt. High tone only 69194 49.74 each 41.45 ex VAT Small 6v horn 72mm diameter. 100db. Supplied complete with mounting bracket with two 6mm diameter holes 080.335 8.38 each 6.98 ex VAT s correct at March 2014

www.holden.co.uk 12 volt Horns Windtone horns Pair of Windtone horns giving high and low notes. 12V. As used on MG TD, TF, MGA, Triumph TR2, TR3 and many other British cars of the 1940s and 1950s. Sold as a pair /080.222 100.80 pair 84.00 ex VAT lucas 9h Windtone horn Reproduction of the 12 volt horn used on many British cars and motorcycles from 1964 onwards Low tone SD/080.220 37.28 each 31.07 ex VAT High tone SD/080.221 37.28 each 31.07 ex VAT lucas altette horn Reproduction of the 12 volt Lucas 'Altette' chrome and black horn as fitted to MG TC, Rover and Wolseley cars 080.237 123.25 each 102.71 ex VAT parts kit for altette horn Comprises chrome front ring and six chromed dome nuts for the periphery, a chromed dome nut and locknut for the centre 080.638 23.94 each 19.95 ex VAT Windtone horns Pair of windtone horns giving high and low notes. 12V. Black plastic body chrome grilles and covers. is 87mm diameter. Supplied with top mounting brackets, screws, nuts and a relay SD/080.915 21.48 pair 17.90 ex VAT twin tone air horn complete with compressor, relay etc. and chromed metal trumpets. 12V 080.333 34.80 per set 29.00 ex VAT twin tone air horn Complete with compressor, relay etc. 12V. Good for when you want to give them a BLAST! SD/080.223 32.52 per set 27.10 ex VAT For latest prices refer to website musical horn Set 5 powerful and durable air horns complete with compressor, relay, instructions and all fittings for easy installation. Horn trumpets are red. Plays 'Dixie Land' SD/080.916 62.40 per set 52.00 ex VAT more on next page 117

12 volt Horns +44 (0) 1885 488 488 BUll horn Overall height 210mm. Horn is metal, cover is red plastic. Horn has a built-in switch operated by a lever on the side by means of the cable supplied. The end result is a really good BELLOW, as in bull! SD/080.912 46.80 each 39.00 ex VAT old timer horn Klaxon type with red plastic trumpet 080.229 43.45 each 36.21 ex VAT old timer horn Klaxon type with chrome plastic trumpet SD/080.334 46.80 each 39.00 ex VAT Chrome/StainleSS horn Made from stainless steel and chromium plated brass Low tone (left) 080.321 33.79 each 28.16 ex VAT High tone (right) 080.320 33.79 each 28.16 ex VAT plastic Windtone horn Low tone 080.331 11.40 each 9.50 ex VAT High tone 080.332 11.40 each 9.50 ex VAT Chrome rim horn Chrome rim with black centre, 12V, twin Lucar 6.4mm terminals. This horn is 'E' marked E6 080.330 15.54 each 12.95 ex VAT Chrome horn Round chrome horn 100mm (3 7 8") diameter 080.231 22.91 each 19.09 ex VAT Chromed horn Round chromed horn 147mm (5 3 4") diameter 080.230 39.78 each 33.15 ex VAT plastic Windtone horn Low tone 080.468 11.40 each 9.50 ex VAT High tone 080.469 11.40 each 9.50 ex VAT Small round horn 70mm diameter. 100db. Supplied complete with mounting bracket with one 8mm diameter hole. E marked 080.336 9.36 each 7.80 ex VAT round 110dB horn 100mm diameter. 110db Black 080.337 17.98 each 14.98 ex VAT Chrome 080.338 17.98 each 14.98 ex VAT Single terminal horn Low tone 080.227 13.72 each 11.43 ex VAT High tone 080.228 13.72 each 11.43 ex VAT 118 s correct at March 2014