LETTER OF INFORMATION
On behalf of Dynamic Technical Training, DTT Technical and Centennial College, Canada, I want to congratulate on your qualification to the GM Advanced Technician Training Program. We are all excited to welcome you as part of the 12 th group of students to participate in this one-of-a-kind program. Below, please find important dates. Important Dates Date to be advised Pre-training Medical Examination for you. Approved POEA hospitals/clinics will be advised. A representative of the training center will coordinate and assist you with medical testing and timing. Sunday, September 11, 2011 09:00 17:00 Check-in procedure at GM ATTC. 16:00 17:00 Orientation of GM ATTC campus. Monday, September 12, 2010 08:30 Day One of the 13-week training. Date to be advised Final POEA Medical Examination. Thursday, December 8, 2011 15:00 Graduation Ceremony. Friday, December 9, 2011 Last Day of the 13-week training. Saturday, December 10, 2011 Check-out procedure from GM ATTC. Approx February 2012 Group 12 Advanced Technicians depart to the Middle-East. Travel instructions to the training center Please, visit our website at www.gmattc.com for directions. address: GM Advanced Technician Lourdes High School Complex Veterans Ville, San Roque 3012, Angat Bulacan
Check-in The accommodation at the training center is available for you as of: Sunday September 11, 2011 as indicated earlier. Below, please find a list of the recommended items for you to bring to the training center; Mandatory l items are highlighted in Bold Italic font. Clothes/Shoes Personal Care Documents Toiletries Safety shoes Personal Passport valid for at Shampoo / Soap Medicine least 24 months Underwear Eye Glasses Passport Pictures Comb / Brush (20 identical pictures) Socks Nail Clippers Original documents of Medical Examination Toothbrush + Toothpaste Leisurewear Contact Lens Case Petty Cash (pocket Razors, Shaving Contact Lens Solution money) Cream Sportswear Contact Lens Preparations & Extra Lenses Credit Card or ATM card After Shave Rubber Shoes Photocopies of Hair Spray / Hair Gel Documentation Small Flashlight Education Certificates Deodorant Driver s License Daily schedule Item Timing Breakfast 07:00 08:00 Start of Training 08:30 Morning Program 08:30 10:40 Break 10:40 10:50 Morning Program cont. 10:50 12:50 Lunch 12:50 13:30 Afternoon Program 13:30 15:30 Break 15:30 15:40 Afternoon Program cont. 15:40 17:30 End of Training 17:30 Dinner 17:30 18:30 During the intensive 13-week training program, the majority of the courses that are included in the GM Academy Middle East curriculum and offered to all the GM Middle East dealers are delivered to you, enabling you to meet the high expectations from the GM Dealers.
Training Program Below, please find an overview of the courses that will be offered to you. The GM training environment contains both Web Based Training (WBT) and Instructor Based Training (IBT). The WBT courses are prerequisites for IBT courses and must be completed by you before you participate in an IBT. You will receive your own ID & Password to the GM Training website that gives you an unlimited access, 24/7. Custom Technical Area Basic Course Description Delivery Method LMS101.01W Introduction to the GM LAAM LMS WBT 10041.10W-R2 SI Overview WBT 16048.16W-R2 Tech 2 Familiarization WBT A2407.03ME-W Introduction to Customer Management WBT Intermediate Course Description Delivery Method A1079.04ME GM Difference Customer Enthusiasm IBT A1008.16ME Service Information IBT C1635.16ME Tech 2 IBT A1002.24ME MDI & Global Diagnostic System IBT 18043.01W-R4 Electrical/Electronics Stage 1 WBT 18044.17W Body Control & Communication Systems WBT 18043.02W-R4 Electrical/Electronics Stage 2 WBT 18043.04S Electrical/Electronics Terminals and Connectors WBT 18043.03W-R3 Electrical/Electronics Stage 3 WBT 50250.14T1 Delphi Micro 64 Connector System Service WBT 18044.20W GM Global Electrical Systems WBT 16048.26W Global Diagnostic System WBT 50240.31T1 GM Terminal and Connector Information WBT 18043.12T1 SI Navigation for Wire, Connector & Terminal Repair WBT 18043.11T1 J-38125 Terminal Repair Kit Structure & Usage WBT 50250.25T1 GM Terminal Repair Kit Update Procedures for J-38125-G WBT 50250.26T1 Flex Beam Technology Terminal WBT A18043.16ME J38125 Terminal Kit & Repairs IBT 16041.07W-R2 Battery, Charging and Starting Systems WBT A1802.16ME Batteries, Charging and Cranking Systems IBT 22048.35W-R2 GM Supplemental Restraint Systems WBT A1810.16ME Supplemental Inflatable Restraints (SIR) IBT A1806.24ME Electrical Diagnosis (Part 1) IBT A1807.16ME Electrical Diagnosis (Part 2) IBT 11044.04W1 HVAC Systems and Operation Stage 1 WBT A1101.16ME Introduction to AC Refrigeration Systems IBT 11044.04W2 HVAC Systems and Operation Stage 2 WBT A1711.16ME HVAC System Operations IBT 13041.11W-R2 GM Steering Systems and Diagnostics WBT 13044.11W-R2 GM Chassis Control Systems WBT
A1025.32ME Suspension and Alignment IBT 50240.11T2 Micrometer Basics Tech Assist 50240.34T1 Brake Drum Measurement WBT 15045.11W1-R2 GM Braking Systems 1 WBT 15045.11W2-R2 GM Braking Systems 2 WBT 15045.13T1 Anti-Lock Braking Systems Overview Tech Assist 15045.45T2 Vehicle Stability Enhancement System (VSES) Operation Tech Assist 50250.21T1 Active Booster Brake System WBT A1502.16ME Intro to Base Brakes IBT A1501.16ME Introduction to ABS, TCS and VSC: Bosch 8.0 IBT 14041.15W Axles and Propshafts WBT A1402.16ME Rear Axle & Driveshaft IBT 14043.15W All Wheel Drive/ Four Wheel Drive Systems WBT A2051.16ME All Wheel Drive/ Four Wheel Drive Systems IBT 13042.11W-R2 Noise, Vibration, and Harshness(NVH) WBT A1005.16ME Vibration Correction IBT A1801.24ME Integrated Controls IBT A1003.16ME Troubleshooting Strategies IBT 16044.16W1 GM Powertrain Performance 1 WBT 16044.16W2 GM Powertrain Performance 2 WBT 16044.16W3 GM Powertrain Performance 3 WBT A1807.24ME Engine Management 1 IBT 16044.16W4 GM Powertrain Performance 4 WBT A1808.16ME Engine Management 2 IBT 16044.16W5 GM Powertrain Performance 5 WBT A1809.16ME Engine Management 3 IBT 16043.51W1 Engine Mechanical Diagnosis and Measurement 1 WBT 16043.51W2 Engine Mechanical Diagnosis and Measurement 2 WBT A1608.16ME High Features Engines IBT 17041.23W Automatic Transmission/Transaxle Theory, Operation & Diagnostics WBT A1701.40ME Introduction to Automatic Transmissions & 4L60E IBT A1710.40ME 6L80-E Transmission and Diagnosis IBT Advanced Course Description Delivery Method 11044.14T1 Windshield Temperature Inside Moisture Sensor WBT 13044.10W Electronic Suspension Systems WBT 13041.13T1 Rack-mount Electric Steering WBT 13044.16T1 Continuous Damping Control System WBT 13044.11S-R2 GM Chassis Control Systems WBT 13044.12T2 Tire Pressure Monitoring (TPM) Systems Diagnostics WBT 15045.12T2 HUMMER H2 and H3 Electro-Hydraulic Brake Boost System WBT A1001.16ME Diagnostic Strategies IBT 15045.11S-R3 GM Braking Systems WBT
Training Team Technical Instructor Mr. Ernesto Guina Mr. Edward Romero Mr. Carlos Javier VIII Mr. Ryan Coria Mr. Carlos Breta There will be a total of eight (8) major course examinations during the 13-week training program. You are expected to write eight (8) successful major course examinations, but you have to write six (6) or more successful major course examinations to be able to graduate from this training program. If you fail in a major course examination you will be requested to take a rewrite. It is mandatory for every Student to take the rewrite of the failed major course examination to determine the Students comprehension and competency of the particular training course. Furthermore, there are hands-on activities and those will be observed and evaluated by your Instructors. The results of the major course examinations, completion of WBTs, results of the Hands-on activities and your Instructors evaluations will determine how successful you are in completion of the this demanding training program. Contacts: Ms. Charlene Mallari Ms. Joanna Aday Program Manager Training Specialist GM Advanced Technician Mobile Phone: 0918 985 9402 Mobile Phone: 0928 552 4227 Mr. Per Storskog Manager GM Advanced Technician Mobile Phone: 0920 969 7673 All staff members of DTT Technical are wishing you an enjoyable training experience as you now will transform your professional career and become a GM Advanced Technician, with a great future within GM Middle East Operations, GM MEO. Best regards, Per Storskog Manager GM ATTC