0 INSTALLATION INSTRUCTIONS Safety glasses should be worn at all times while installing this product. YEARS: 05 MAKE: FORD MODEL: TRANSIT STYLE: VAN WARNING: NEVER EXCEED YOUR VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY WEIGHT CARRYING: TRAILER WEIGHT: TONGUE WEIGHT: 8,000 800 WEIGHT DISTRIBUTION: TRAILER WEIGHT: TONGUE WEIGHT: 0,000,000 PRO INSTALL TIME: NOVICE INSTALL TIME: INSTALLATION REQUIRES: 5 MIN. 0 MIN. IF YOU ARE HESITANT TO UNDERTAKE THIS TASK ON YOUR OWN, CONTACT AN AUTHORIZED CURT INSTALLER FOR ADDITIONAL ASSISTANCE. INSTALLATION TIPS:. BEFORE YOU BEGIN INSTALLATION, READ ALL INSTRUCTIONS THOROUGHLY.. TO EASE INSTALLATION, PEOPLE MAY BE REQUIRED.. USING PROPER TOOLS WILL GREATLY IMPROVE THE QUALITY OF THE INSTALL AND REDUCE THE TIME REQUIRED.. NEED HELP OR HAVE SOME QUESTIONS? CALL TECHNICAL SUPPORT AT 800.798.08 VEHICLE PHOTO: LEVEL OF DIFFICULTY: EASY SAFETY GLASSES SPRAY LUBRICANT WIRE PIPE BRUSH EASY MODERATE CHALLENGING RATCHET " SOCKET EXTENSION 5mm /" SOCKET LOWER SPARE TIRE ENLARGE HOLE REPRESENTATIVE PHOTO HITCH ILLUSTRATION: TORQUE WRENCH DRILL BIT POWER DRILL 9/6" CLEAN WELDNUTS FISHWIRE HARDWARE SCAN FOR MORE INFO MAKE SURE YOUR HITCH MATCHES PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE ALL FASTENERS ARE TIGHT AND ALL STRUCTURAL COMPONENTS ARE SOUND CURT Manufacturing LLC. warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser. If the product is found to be defective, CURT Manufacturing LLC. may repair or replace the product at their option, when the product is returned, prepaid, with proof of purchase. Alteration to, misuse of, or improper installation of this product voids the warranty. CURT Manufacturing LLC.'s liability is limited to repair or replacement of products found to be defective, and specifically excludes liability for incidental or consequential loss or damage. For more information log onto www.curtmfg.com, & for helpful towing tips log onto www.hitchinfo.com 7/6/0
INSTALLATION WALKTHROUGH: ITEM QTY PART NUMBER /- x / Parts List DESCRIPTION CARRIAGE BOLT NOTE: Lower spare tire for eaze of installation.. Remove () bolts in each frame rail and set aside for install. HFN HEX FLANGE NUT CM-SP6.50 x.00 x.00" SQUARE HOLE SPACER _ x 0 FISHWIRE /" x 0" FISHWIRE PASSENGER SIDE PLATE. Fishwire () / bolts and spacers into each bumper frame rail. Raise hitch into loaction and secure with the factory M bolts and () /" hex nuts. FACTORY BOLTS DRIVER SIDE PLATE DRILL HOLE (BOTH SIDES) For more information log onto www.curtmfg.com, & for helpful towing tips log onto www.hitchinfo.com
INSTALLATION WALKTHROUGH:. Drill out the /6 hole using 9/6" drill bit in each rear bumper rail. Fishwire () remaining / bolts and spacers into each bumper frame rail. Torque M bolts to 90 ft-lbs Torque /" hex nuts to 0 ft-lbs. Raise spare tire into location if lowered. Instalation Complete For more information log onto www.curtmfg.com, & for helpful towing tips log onto www.hitchinfo.com
0 7/7/0 05 FORD TRANSIT GROSS LOAD CAPACITY WHEN USED AS A WEIGHT CARRYING HITCH: 8,000 TRAILER WEIGHT & 800 TONGUE WEIGHT. GROSS LOAD CAPACITY WHEN USED AS A WEIGHT DISTRIBUTION HITCH: 0,000 TRAILER WEIGHT &,000 TONGUE WEIGHT ***DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY.*** HAVING INSTALLATION QUESTIONS? CALL TECHNICAL SUPPORT AT -800-798-08 ITEM QTY PART NUMBER /- x / HFN CM-SP6 _ x 0 FISHWIRE Parts List DESCRIPTION CARRIAGE BOLT HEX FLANGE NUT.50 x.00 x.00" SQUARE HOLE SPACER /" x 0" FISHWIRE TOOLS REQUIRED SAFTEY GLASSES SPRAY LUBRICANT WIRE PIPE BRUSH RATCHET 5mm, /" SOCKET " SOCKET EXTENSION POWER DRILL 9/6" DRILL BIT TORQUE WRENCH DRIVER SIDE FRAME RAIL FACTORY HARDWARE PASSENGER SIDE FRAME RAIL HITCH WEIGHT: INSTALL TIME 5 PROFESSIONAL: 5 NOVICE (DIY): INSTALL NOTES: 0 - LOWER SPARE TIRE - WELDNUT CLEANING - DRILLING REQUIRED - FISHWIRE REQUIRED MINUTES MINUTES INSTALLATION STEPS NOTE: Lower spare tire for ease of installation. Ø 9/6" DRILL HOLE (BOTH SIDES). Remove () bolts in each side frame rail with the M socket and set aside for install. Clean frame rail weldnuts as needed with lubricant and brush.. Then fishwire () / bolts and spacers into each bumper frame rail. Raise hitch into location, careful not to push bolts back into frame and secure with the factory M bolts and the () /" hex nut.. Drill out the /6 hole using 9/6" drill bit in each rear bumper rail. Then fishwire () remaining / bolts and spacers into each bumper frame rail. Torque M bolts to 90 ft-lbs Torque /" hex nuts to 0 ft-lbs. Raise spare tire into original location if lowered for install. PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE THAT ALL FASTENERS ARE TIGHT AND THAT ALL STRUCTURAL COMPONENTS ARE SOUND. Scan for more information CURT Manufacturing LLC., warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser. If the product is found to be defective, CURT Manufacturing LLC., may repair or replace the product, at their option, when the product is returned, prepaid, with proof of purchase. Alteration to, misuse of, or improper installation of this product voids the warranty. CURT Manufacturing LLC.'s liability is limited to repair or replacement of products found to be defective, and specifically excludes liability for incidental or consequential loss or damage.