GRUNDFOS DATA BOOKLET ydro MPC Booster systems with 2 to 6 ums 50 z
Contents Introduction Benefits 3 Product data Performance range 5 Product range 6 Tye key 7 Oerating conditions 7 Construction Pum 8 Shaft seal 8 Motor 8 Manifold 9 Control cabinet 9 CU 351 10 IO 351 10 Base frame 10 System comonents 10 Flange dimensions 10 Functions Overview of control variants 11 CU 351 control anel 12 Overview of functions 14 Descrition of selected functions 15 Installation Mechanical installation 22 Electrical installation 23 Sizing Sizing 24 Understanding the curve charts 30 Examle: ow to select a system 31 Curve conditions ow to read the curve charts 32 Curve charts ydro MPC with CRI(E) 3 33 ydro MPC with CRI(E) 5 34 ydro MPC with CRI(E) 10 35 ydro MPC with CRI(E) 15 36 ydro MPC with CRI(E) 20 37 ydro MPC with CR(E) 32 38 ydro MPC with CR(E) 45 39 ydro MPC with CR(E) 64 ydro MPC with CR(E) 90 41 ydro MPC with CR(E) 120 42 ydro MPC with CR(E) 150 43 Technical data ydro MPC with CRI(E) 3 / CRI(E) 5 44 ydro MPC with CRI(E) 10 48 ydro MPC with CRI(E) 15 / CRI(E) 20 52 ydro MPC with CR(E) 32 58 ydro MPC with CR(E) 45 / CR(E) 64 61 ydro MPC with CR(E) 90 67 ydro MPC with CR(E) 120 / CR(E) 150 71 Otional equiment Diahragm tank 75 Redundant rimary sensor 75 Dry-running rotection 76 Pilot um 76 Byass connection 76 Position of non-return valve 77 Stainless steel non-return valve 77 Emergency oeration switch 77 Reair switch 77 Isolating switch 77 Main switch with switching off of the neutral conductor 78 Oerating light, system 78 Oerating light, um 78 Fault light, system 78 Fault light, um 79 Panel light and socket 79 IO 351B interface 79 Ethernet 79 GENIbus module 80 CIU communication interface 80 Transient voltage rotection 81 Lightning rotection 81 Phase failure monitoring 81 Beacon 81 Audible alarm 81 Voltmeter 81 Ammeter 81 Accessories Dry-running rotection 82 Diahragm tank 82 Foot valve 83 Machine shoe 83 Extra documentation 83 Alternative booster systems Alternative booster systems 84 Further roduct documentation WebCAPS 85 WinCAPS 86 2
Introduction ydro MPC Grundfos ydro MPC booster systems are designed for transfer and ressure boosting of clean water in laces such as these: waterworks blocks of flats hotels industry hositals schools. As standard, ydro MPC booster systems consist of two to six identical CRI(E)/CR(E) ums connected in arallel and mounted on a common base frame rovided with a control cabinet and all the necessary fittings. Most of the booster systems are available with either CR(I) ums and/or CR(I)E ums. For further information, see age 9. The ums of the booster system can be removed without interfering with the iework on either side of the manifolds. ydro MPC booster systems come in three control variants. For further information, see Product range on age 6 and Overview of control variants on age 11. ydro MPC-E Booster systems with two to six identical electronically seed-controlled ums. Piework connection from R 2 to DN 350. From 0.37 to 22 kw, ydro MPC-E is fitted with CR(I)E ums with integrated frequency converter. As from 30 kw, ydro MPC-E is fitted with CR ums connected to external Grundfos CUE frequency converters (one er um). ydro MPC-F Booster systems with two to six identical CR(I) ums connected to one external Grundfos CUE frequency converter. The seed-controlled oeration alternates between the ums of the booster system. Piework connection from R 2 to DN 350 and motor sizes from 0.55 to 55 kw. ydro MPC-S Booster systems fitted with two to six identical mainsoerated CR(I) ums, iework connection from R 2 to DN 350 and motor sizes from 0.37 to 55 kw. Benefits Perfect constant-ressure control Fig. 1 CU 351 The ums of the ydro MPC booster system are controlled individually by the CU 351 multi-um control unit which contains alication-otimised software and um curve data. The CU 351 thus knows the exact hydraulic and electrical data of the ums to be controlled. User-friendliness ydro MPC features a built-in start-u wizard in a wide range of local languages that guides the installer through a series of stes until the booster system is correctly installed and commissioned. When the installation is comlete, the simle, user-friendly interface makes sure that day-to-day oeration is equally easy. Reliability Fig. 2 Grundfos CR ums ydro MPC is built on the highly renowned Grundfos CR um range. CR ums are known for their reliability, efficiency and adatability. Every vital iece of the ydro MPC is Grundfos made. You are thus guaranteed long-lasting technology that requires a minimum of maintenance and rovides a maximum of efficiency. GrA0812 TM04 4568 1709 3
Introduction ydro MPC Low energy consumtion ydro MPC booster systems come with EFF1 motors as standard. EFF1 motors are known for their high efficiency and their low noise level. Flexibility The elements of the ydro MPC can be combined in a number of ways to make sure that we build the erfect solution for you! Custom-built solutions If this data booklet does not rovide you with a solution that meets your secific uming needs, lease contact us. 4
Product data ydro MPC Performance range 0 ydro MPC 50 z ISO 9906 Annex A 300 200 150 6 x CR 120 6 x CR 150 90 80 70 50 30 4 x CRI 3 4 x 6 x 6 x 6 x CRI 5 CRI 15 CR 32 CR 64 6 x 6 x 6 x 6 x CRI 10 CRI 20 CR 45 CR 90 20 1 2 4 6 8 10 20 80 200 0 0 0 Q [m³/h] TM03 0981 1209 Note: The area within the dotted line alies to ydro MPC booster systems available on request. The erformance range is based on the standard range of the CR and CRI ums. 5
Product data ydro MPC Product range TM03 0993 0905 PT PT PT TM03 1265 1505 TM03 0999 0905 Control variant ydro MPC-E ydro MPC-F ydro MPC-S ydraulic data Max. head 155 155 155 Flow rate [m 3 /h] 0-1080 0-1080 0-1080 Liquid temerature [ C] 0 to +70 0 to +70 0 to +70 Max. oerating ressure [bar] 16 1) 16 1) 16 1) Motor data Number of ums 2-6 2-6 2-6 Motor ower [kw] 0.37-55 2) 0.55-55 0.37-55 Shaft seal QQE (SiC/SiC/EPDM) Materials CRI(E) 3 to CRI(E) 20: Stainless steel EN/DIN 1.4301/AISI 304 CR(E) 32 to CR(E) 150: Cast iron and stainless steel EN/DIN 1.4301/AISI 304 Manifold: Stainless steel Manifold: Galvanised steel 3) Piework connection Union connection R 2 to R 2 1/2 R 2 to R 2 1/2 R 2 to R 2 1/2 DIN flange DN 80 to DN 350 DN 80 to DN 350 DN 80 to DN 350 Functions Constant-ressure control 4) Automatic cascade control Pum changeover/alternation Sto function Proortional-ressure control GENIbus communication (external) Integrated frequency converter (in um) - - External frequency converter (in cabinet) - Ethernet connection Alternative setoints Redundant rimary sensor (otion) Standby um Emergency run Available as standard. Available on request. 1) Booster systems with a maximum oerating ressure higher than 16 bar are available on request. 2) ydro MPC-E booster systems from 0.37 to 22 kw are fitted with seed-controlled CR(I)E ums with integrated frequency converters. ydro MPC-E booster systems from 30 to 55 kw are fitted CR(I) ums connected to Grundfos CUE frequency converters. 3) Galvanised steel manifolds are available on request in some regions. For further information, contact Grundfos. 4) The ressure will be almost constant between set and sto. For further information, see age 11. 6
Product data ydro MPC Tye key Examle ydro MPC -E /G /NS 3 CRIE 5-8 (* 3x380-415V, 50/ z, N, PE Tye range Subgrous: Pums with integrated frequency converter (0.37-22 kw) - one er um: -E Pums with Grundfos CUE frequency converter (30 kw and above) - one er um: -E Pums with external Grundfos CUE frequency converter: -F Mains-oerated ums (start/sto): -S Manifold material : Stainless steel /G : Galvanised steel /OM : Other materials Suction manifold : With suction manifold /NS: Without suction manifold Number of ums with integrated frequency converter and um tye Number of mains-oerated ums and um tye Suly voltage, frequency (* Code for custom-built solution. Oerating conditions Oerating ressure As standard, the maximum oerating ressure is 16 bar. On request, Grundfos offers ydro MPC booster systems with a higher maximum oerating ressure. Temerature Liquid temerature: Ambient temerature: 0 C to +70 C. 0 C to + C. Relative humidity Max. relative humidity: 95 %. 7
Construction ydro MPC Pum Motor Couling Shaft seal All ums are equied with a maintenance-free mechanical QQE shaft seal of the cartridge tye. Seal faces are silicon carbide/silicon carbide. Rubber arts are of EPDM. Note: Other shaft seal variants are available on request. Shaft seal (cartridge tye) Imellers Pum head Sleeve GR3395 Base Fig. 3 CR um Staybolts Base late CR ums are non-self-riming, vertical multistage centrifugal ums. Each um consists of a base and a um head. The chamber stack and outer sleeve are secured between the um head and the base by means of staybolts. The base has suction and discharge orts on the same level (in-line) and of the same ort size. CRE and CRIE ums are based on CR and CRI ums. The difference between the CR and CRE um range is the motor. CRE and CRIE ums are fitted with a motor with integrated frequency converter. CR and CRE ums have um head and base of cast iron while CRI and CRIE ums have um head and base of stainless steel. All hydraulic arts are made of stainless steel. For further information, see the following data booklets: Title Publication number CR, CRI, CRN, CRE, CRIE, CRNE V7023751 CR, CRI, CRN, CRT, CRE, CRIE, CRNE, CRTE custom-built ums 96486346 Grundfos E-ums 96570076 The data booklets are available in WebCAPS on www.grundfos.com. See age 85. GR5357 - GR3395 Fig. 4 Cartridge shaft seal The shaft seal can be relaced without dismantling the um. The shaft seal of ums with motors of 11 kw and u can be relaced without removing the motor. For further information, see the data booklet on shaft seals, ublication number 96519875. The data booklet is available in WebCAPS. See age 85. Motor CR and CRI ums CR and CRI ums are fitted with a totally enclosed, fan-cooled, 2-ole Grundfos standard motor with rincial dimensions in accordance with the EN standards. Electrical tolerances to EN 034. 1) IP65 available on request. Standard motor Mounting designation U to 4 kw: V 18 From 5.5 kw: V 1 Insulation class F Efficiency class EFF1 Enclosure class IP55 1) Suly voltage (tolerance: ± 10 %) P 2 : 0.37 to 1.5 kw: 3 x 220-2/380-415 V, 50 z P 2 : 2.2 to 11 kw: 3 x 380-415 V, 50 z P 2 : 15 to 55 kw: 3 x 380-415/6-690 V, 50 z Three-hase Grundfos motors from 3 kw and u have a built-in thermistor (PTC) according to DIN 44 082 (IEC 34-11: TP 211). For information about the um s osition in the booster system, see fig. 7 on age 10. 8
Construction ydro MPC CRE and CRIE ums CRE and CRIE ums are fitted with a totally enclosed, fan-cooled, 2-ole motor with integrated frequency converter. Princial dimensions are in accordance with EN standards. Electrical tolerances to EN 034. Motors with integrated frequency converter require no external motor rotection. The motor incororates thermal rotection against slow overloading and seizure (IEC 34-11: TP 211). Manifold Motor with integrated frequency converter P 2 : 1.1 kw P2: 0.75 to 7.5 kw P2: 11 to 22 kw Mounting designation V18 U to 4 kw: V 18 From 5.5 kw: V 1 Insulation class F Efficiency class EFF1 EFF1 EFF1 Enclosure class IP54 Suly voltage (tolerance: ± 10 %) 1 x 200-2 V, 50/ z 3 x 380-480 V, 50/ z 3 x 380-415 V, 50/ z A suction manifold of stainless steel (EN DIN 1.4571) is fitted on the suction side of the ums. Control cabinet The control cabinet is fitted with all the necessary comonents. If necessary, ydro MPC booster systems are fitted with a fan to remove surlus heat generated by the frequency converter. Control cabinet variants The control cabinets are divided into four different designs based on construction: Design A: Systems with the control cabinet mounted on the same base frame as the ums. Design B: Systems with the control cabinet centred on the base frame. Design C: Systems with the control cabinet mounted on its own base for floor mounting. The control cabinet can be laced u to 2 metres from the ums. Design D: Systems with the control cabinet mounted on its own base frame. The control cabinet can be laced u to 2 metres from the ums. For further information, see fig. 7 on age 10 and the chater of Technical data for the individual ydro MPC. A discharge manifold of stainless steel (EN DIN 1.4571) is fitted on the discharge side of the ums. An isolating valve and a non-return valve are fitted between the discharge manifold and the individual ums. The non return valve may be fitted on the suction side on request. As an alternative, ydro MPC is available with galvanised steel manifolds in some countries. If a ydro MPC with galvanised steel manifolds is ordered, the base frame and stand for the controller also come in galvanised steel. For further information, contact Grundfos. For information about the osition of the suction and discharge manifold, see fig. 7 on age 10. 9
Construction ydro MPC CU 351 CU 351, the multi-um control unit of the ydro MPC, is laced in the door of the control cabinet. System comonents GrA0812 Fig. 5 CU 351 The CU 351 features an LCD dislay, ten buttons and two indicator lights. The control anel enables manual setting and change of arameters such as setoint, start/sto of system or individual ums. The CU 351 has alication-otimised software for setting the system to the alication in question. IO 351 The IO 351 is a module for exchange of digital and analog signals between the CU 351 and the remaining electrical system via GENIbus. The IO 351 comes in the variants A and B. Fig. 6 IO 351A and IO 351B IO 351A The IO 351A is used for one to three mains-oerated Grundfos ums. IO 351B The IO 351B is used for one to six mains-oerated Grundfos ums and/or ums controlled by external Grundfos CUE frequency converters. The module can also be used as an inut-outut module for communication with monitoring equiment or another external equiment. Base frame A ydro MPC booster system has a common base frame. The ums are fixed to the base frame by means of bolts. The control cabinet is fixed to the base frame by means of a stand. See fig. 7 on age 10. The base frame and stand are of stainless steel EN DIN 1.4301. TM03 2110 - GrA0815 Fig. 7 System comonents Pos. Descrition Quantity 1 Control cabinet 1 2 Namelate 1 3 Suction manifold (stainless steel) 1 4 Isolating valve 2 er um 5 Base frame (stainless steel) 1 6 Non-return valve 1 er um 7 Discharge manifold (stainless steel) 1 8 Pressure transmitter/gauge 1 9 Pum 2-6 10 Diahragm tank 1 Flange dimensions PN 16 flanges D 1 D 2 D 3 PN 25 flanges D 1 D 2 D 3 S S TM02 7720 3803 TM02 7720 3803 TM04 4110 0709 Standard: EN 1092-2 PN 16 (1.6 MPa) Nominal diameter (DN) DN 80 125 150 200 250 D 1 80 125 150 200 250 D 2 1 180 210 2 295 355 D 3 200 220 250 285 3 5 S 8x19 8x19 8x19 8x23 12x23 12x28 Standard: EN 1092-2 PN 25 (2.5 MPa) Nominal diameter (DN) DN 300 350 D 1 300 350 D 2 430 490 D 3 485 555 S 16x30 16x33 10
Functions ydro MPC Overview of control variants Booster systems with seed-controlled ums Booster systems with ums connected to one CUE frequency converter Booster systems with mains-oerated ums ydro MPC-E ydro MPC-F ydro MPC-S ydro MPC booster system with three CR(I)E ums. ydro MPC booster system with three CR ums. One of the ums is connected to an external Grundfos CUE frequency converter in the control cabinet. The seed-controlled oeration alternates between the ums of the ydro MPC. ydro MPC booster system with three mainsoerated CR(I) ums. TM03 0993 0905 PT PT PT TM03 1265 1505 TM03 0999 0905 One CR(I)E um in oeration. One CR um connected to an external Grundfos CUE frequency converter in oeration. One mains-oerated CR(I) um in oeration. set Q TM00 7995 2296 set Q TM00 7995 2296 sto set Q TM03 2045 3505 Three CR(I)E ums in oeration. One CR um connected to an external Grundfos CUE frequency converter and two mains-oerated CR ums in oeration. Three mains-oerated CR(I) ums in oeration. set Q TM00 7996 2296 set Q TM00 7998 2296 sto set Q TM03 2046 3505 ydro MPC-E maintains a constant ressure through continuously variable adjustment of the seed of the CR(I)E ums connected. The erformance is adjusted to the demand through cutting in/out the required number of CR(I)E ums and through arallel control of the ums in oeration. Pum changeover is automatic and deends on load, oerating hours and fault. All ums in oeration will run at equal seed. ydro MPC-F maintains a constant ressure through continuously variable adjustment of the seed of the CR um connected to an external Grundfos CUE frequency converter. The seed controlled oeration alternates between the ums. One CR um connected to the Grundfos CUE frequency converter always starts first. If the ressure cannot be maintained by the um, one or two mains-oerated CR ums will be cut in. Pum changeover is automatic and deends on load, oerating hours and fault. ydro MPC-S maintains an almost constant ressure through cutting in/out the required number of ums. The oerating range of the ums will lie between the lines set and sto (cut-out ressure). The cut-out ressure cannot be set, but is calculated automatically. Pum changeover is automatic and deends on load, oerating hours and fault. 11
Functions ydro MPC CU 351 control anel Menu Status 2 3 1 5 4 6 7 8 9 13 12 10 11 TM04 4104 0709 TM04 4106 0709 Fig. 8 CU 351 control anel Key Pos. Descrition 1 Dislay 2 Arrow to the right 3 el 4 U 5 Down 6 Plus 7 Minus 8 Esc 9 ome 10 Ok 11 Indicator light, oeration (green) 12 Indicator light, fault (red) 13 Contrast Fig. 9 Menu Status Descrition Reading of rocess value (PV) of control arameter and selected setoint (SP). Grahical illustration of system (uer dislay half). Indication if any incidents occur during oeration (middle of dislay). Reading of erformance of system and individual ums (lower dislay half). Button for further information. Active buttons are illuminated. Menu Oeration TM04 4107 0709 Fig. 10 Menu Oeration Descrition Setting of basic arameters, for instance setoint, start/sto of system or individual ums. Reading of selected setoint and current setoint. Button for further information. Active buttons are illuminated. 12
Functions ydro MPC Menu Alarm Menu Settings TM04 4108 0709 TM04 4109 0709 Fig. 11 Menu Alarm Descrition Overview of current warnings and alarms in clear text with detailed information: - What the cause of the fault is. - Where the fault occurred: System, Pum no. 1 - When the fault occurred (time and date). - When the fault disaeared (time and date). Alarm log with u to 24 warnings and alarms. Button for further information. Active buttons are illuminated. Fig. 12 Menu Settings Descrition Various settings: - external setoint influence - redundant rimary sensor - standby um - sto function - roortional ressure - dislay language - Ethernet, etc. Button for further information. Active buttons are illuminated. 13
Functions ydro MPC Overview of functions ydro MPC -E -F -S Functions via the CU 351 control anel Constant-ressure control 1) Automatic cascade control Alternative setoints Redundant rimary sensor (otion) Min. changeover time Number of starts er hour Standby ums Forced um changeover Pum test run Dry-running rotection (otion) Sto function - 2) Password Clock rogram Proortional-ressure control Pilot um Soft ressure build-u Emergency run Pum curve data Flow estimation Limit exceeded 1 and 2 Pums outside duty range Communication Ethernet connection Other bus rotocols: PROFIBUS, LON, Modbus, radio/modem/plc via CIU units. For further information, see Otional equiment, age 75. External GENIbus connection (otion) Standard. On request. 1) The ressure will be almost constant between set and sto. For further information, see age 11. 2) ydro MPC-S will have on/off control of all ums. For further information, see age 17. 14
Functions ydro MPC Descrition of selected functions Constant-ressure control Constant-ressure control ensures that the ydro MPC booster system delivers a constant ressure desite a change in consumtion. When tas are oened, water is drawn from the diahragm tank, if installed in the system. The ressure dros to a set cut-in ressure, and the first seedcontrolled um starts to oerate. The seed of the um in oeration is continuously increased to meet the demand. As the consumtion rises, more ums will cut in until the erformance of the ums in oeration corresonds to the demand. During oeration, the CU 351 controls the seed of each um individually according to known um curve data downloaded into the CU 351. Furthermore, the CU 351 regularly estimates the flow rate to detect whether ums are to be cut-in or cut-out. The flow estimation is based on the best efficiency oint of the um with the aim to reduce the energy consumtion to a minimum. When the water consumtion falls, ums are cut out one by one to maintain the set discharge ressure. Dislay language Dutch Polish Portuguese Russian Swedish Chinese Korean Jaanese Turkish Czech ungarian. Pum curve data TM03 8975 4807 Fig. 14 Pum curve data As standard, ydro MPC will hel you minimise energy consumtion and cut energy costs. By means of um curve data stored from factory, the CU 351 will know exactly which and how many ums to control. These um curve data enables the CU 351 to otimise erformance and minimise energy consumtion. Fig. 13 Dislay language Via the CU 351, you can select the language for the dislay. Otions: British English German Danish Sanish Finnish French Greek Italian TM03 8987 4807 Redundant rimary sensor A redundant sensor can be installed as backu for the rimary sensor in order to increase reliability and revent sto of oeration. The redundant rimary sensor is in the same reference oint as the rimary sensor, i.e. in the discharge manifold of the booster system. Note: The redundant rimary sensor is available as a factory-fitted otion. 15
Functions ydro MPC Automatic cascade control Cascade control ensures that the erformance of ydro MPC is automatically adated to consumtion by switching ums on or off. The system thus runs as energy-efficiently as ossible with a constant ressure and a limited number of ums. Alternative setoints This function makes it ossible to set u to six setoints as alternatives to the rimary setoint. The setoints can be set for closed loo and oen loo. The erformance of the system can thus be adated to other consumtion atterns. Examle A ydro MPC booster system is used for irrigation of a hilly golf course. Constant-ressure irrigation of golf course sections of different sizes and at different altitudes may require more than one setoint. For golf course sections at a higher altitude a higher discharge ressure is required. Number of starts er hour This function limits the number of um starts and stos er hour. It reduces noise emission and imroves the comfort of systems with mains-oerated ums. Each time a um starts or stos, the CU 351 calculates when the next um is allowed to start or sto in order not to exceed the ermissible number of starts er hour. The function always allows ums to be started to meet the requirement, but um stos will be delayed, if needed, in order not to exceed the ermissible number of starts/stos er hour. Standby ums It is ossible to let one or more ums function as standby ums. A booster system with for instance four ums, one having the status of standby um, will run like a booster system with three ums, as the maximum number of ums in oeration is the total number of um minus the number of standby ums. If a um is stoed due to a fault, the standby um will be cut in. This function ensures that the ydro MPC booster system can maintain the nominal erformance even if one of the ums is stoed due to a fault. The status as standby um alternates between all ums of the same tye, for instance electronically seed-controlled ums. Forced um changeover Fig. 16 Forced um changeover This function ensures that the ums run for the same number of oerating hours over time. In certain alications the required flow remains constant for long eriods and does not require all ums to run. In such situations, um changeover does not take lace naturally, and forced um changeover may thus be required. Once every 24 hours the controller checks if any um in oeration has been running continuously for the last 24 hours. If this is the case, the um with the largest number of oerating hours is stoed and relaced by the um with the lowest number of oerating hours. TM03 2366 4807 TM03 2365 4807 Fig. 15 Standby ums 16
Functions ydro MPC Pum test run Sto function TM03 2364 4807 TM03 2355 4807 Fig. 17 Pum test run This function is rimarily used in connection with ums that do not run every day. Benefits: Pums do not seize u during a long standstill due to deosits from the umed liquid. The umed liquid does not decay in the um. Traed air is removed from the um. The um starts automatically and runs for a short time. Dry-running rotection This function is one of the most imortant ones, as dry running may damage bearings and shaft seals. The inlet ressure of the booster system or the level in a tank, if any, on the inlet side is monitored. If the inlet ressure or the water level is too low, all ums will be stoed. Level switches, ressure switches or analog sensors signalling water shortage at a set level can be used. Furthermore, you can set the system to be reset and restarted manually or automatically after a situation with water shortage. Fig. 18 Sto function The sto function makes it ossible to sto the last um in oeration if there is no or a very small consumtion. Purose: to save energy to revent heating of shaft seal faces due to increased mechanical friction as a result of reduced cooling by the umed liquid to revent heating of the umed liquid. This function is only used in ydro MPC booster systems with variable-seed ums. Note: ydro MPC-S will have on/off control of all ums. When the sto function is activated, the oeration of ydro MPC is continuously monitored to detect a low flow rate. If the CU 351 detects no or a low flow rate (Q < Qmin), it will change from normal constantressure oeration to on/off control of the last um in oeration. set On/off band On/off control Q min Normal oeration Q TM03 1692 2705 Fig. 19 On/off band 17
Functions ydro MPC As long as the flow rate is lower than Qmin, the um will run in on/off oeration. If the flow rate is increased to above Qmin, the ums will return to normal constant-ressure oeration. Password Via the CU 351 you can set the ydro MPC is to oerate as energy-saving as ossible or with the highest level of comfort meaning less starts/stos of the last um in oeration during low flow. TM03 2899 4807 TM03 8957 4807 Fig. 21 Password Passwords make it ossible to limit the access to the menus Oeration and Settings in the controller of the booster system. If the access is limited, it is not ossible to view or set any arameter in the menus. Clock rogram Fig. 20 Sto arameters Four sto arameters can be selected: Energy-saving mode (factory setting) If you want the highest energy-saving mode ossible. Medium flow If you want a comromise between the highest energy-saving mode and highest comfort level. ighest comfort level If you want the highest comfort level without too many um starts/stos. Customised settings If you want to make your own settings. Pilot um The ilot um takes over the oeration from the main ums in eriods when the consumtion is so small that the sto function of the main ums is activated. Purose: to save energy to reduce the number of oerating hours of the main ums. Fig. 22 Clock rogram This function makes it ossible to set u to ten events with secification of day and time for their activation/ deactivation. An examle of alication is srinkling of golf courses at fixed times for the individual greens. TM03 8959 4807 18
Functions ydro MPC Proortional ressure Pum curve Setoint Resultant setoint, linear Resultant setoint, square set TM03 89 4807 Starting oint of roortional ressure control (Influence at 0 flow = x % of set ) Fig. 24 Proortional-ressure control TM03 8524 1807 Fig. 23 Proortional ressure This function can be used in alications with a large ie system, for instance a village sulied with water from a uming station or waterworks. Purose: to deliver the required at all times to comensate for friction loss to kee energy consumtion at a minimum to ensure the highest comfort level at taing oint, etc. In situations with high flow rates, the ressure loss in the ie system is relatively high. In order to deliver a system ressure of 5 bar in such a situation, the discharge ressure of the system must be set to 6 bar if the ressure loss in the ie system is 1 bar. In a low-flow situation, the ressure loss in the ie system may be 0.2 bar. ere the system ressure would be 5.8 bar if the setoint was fixed to 6 bar. That is 0.8 bar too high comared with the eak situation above. To comensate for this extensive system ressure, the roortional ressure function of the CU 351 automatically adats the setoint to the actual flow rate. The adatation can be linear or square. Such an automatic adatation offers you large energy savings and otimum comfort at taing oint! 19
Functions ydro MPC Examle: Influence at 0 flow (Q0) = Pressure loss in suly ie x / setoint. Soft ressure build-u Influence at 0 flow (Q0) = 1 bar x / 6 bar = 16.67 %. Setoint at Qmin with roortional-ressure control: 6 bar (6 bar x 0.1667) = 5 bar. Puming station Pressure loss Qmax.: 1 bar Qmin.: 0.2 bar Setoint: 6 bar System ressure Qmax.: 5 bar Qmin.: 5.8 bar TM04 4571 1709 TM03 8970 4807 Fig. 25 Without roortional-ressure control Puming station Setoint: Qmax.:6 bar Qmin.: 5.2 bar Pressure loss Qmax.: 1 bar Qmin.: 0.2 bar Fig. 26 With roortional-ressure control System ressure Qmax.: 5 bar Qmin.: 5 bar TM04 4571 1709 Fig. 27 Soft ressure build-u This function ensures a soft start of systems with for instance emty iework. It has two hases: 1. The iework is slowly filled with water. 2. When the ressure sensor of the system detects that the iework has been filled, the ressure is increased until it reaches the setoint. See fig. 28. 1. Filling hase 2. Pressure build-u hase Filling time Ram time Time [sec] TM03 9037 3207 Fig. 28 Filling and ressure build-u hases The function can be used for reventing water hammering in high-rise buildings with unstable voltage suly or in irrigation alications. 20
Functions ydro MPC Emergency run TM03 8971 4807 Fig. 29 Emergency run The function is esecially suited for imortant systems where the oeration must not be interruted. If activated this function will kee all ums running regardless of warnings or alarms. The ums will run according to a setoint set secifically for this function. 21
Installation ydro MPC Mechanical installation Location The booster system must be installed in a wellventilated room to ensure sufficient cooling of the control cabinet and ums. Note: ydro MPC is not designed for outdoor installation and must not be exosed to direct sunlight. The booster system should be laced with a 1-metre clearance in front and on the two sides for insection and removal. Piework Arrows on the um base show the direction of flow of water through the um. The iework connected to the booster system must be of adequate size. The ies are connected to the manifolds of the booster system. Either end can be used. Aly sealing comound to the unused end of the manifold and fit the screw ca. For manifolds with flanges, a blanking flange with gasket must be fitted. To otimise oeration and mimimise noise and vibration, it may be necessary to consider vibration damening of the booster system. Noise and vibration are generated by the rotations in the motor and um and by the flow in iework and fittings. The effect on the environment is subjective and deends on correct installation and the state of the remaining system. Note: Exansion joints, ie suorts and machine shoes shown in the figure above are not sulied with a standard booster system. All nuts should be tightened rior to start-u. The ies must be fastened to arts of the building to ensure that they cannot move or be twisted. Foundation The booster system should be ositioned on an even and solid surface, such as a concrete floor or foundation. If the booster system is not fitted with vibration damers, it must be bolted to the floor or foundation. Note: As a rule of thumb, the weight of a concrete foundation should be 1.5 x the weight of the booster system. Damening To revent the transmission of vibrations to buildings, it is advisable to isolate the booster system foundation from building arts by means of vibration damers. Which is the right damer varies from installation to installation, and a wrong damer may increase the vibration level. Vibration damers should therefore be sized by the sulier. If the booster system is installed on a base frame with vibration damers, exansion joints should always be fitted on the manifolds. This is imortant to revent the booster system from hanging in the iework. If booster systems are installed in blocks of flats or the first consumer on the line is close to the booster system, it is advisable to fit exansion joints on the suction and discharge ies to revent vibration being transmitted through the iework. 2 1 3 3 1 2 TM03 2154 3805 Fig. 30 Schematic view of hydraulic installation Pos. Descrition 1 Exansion joint 2 Pie suort 3 Machine shoe 22
Installation ydro MPC Exansion joints Exansion joints rovide these advantages: Absortion of thermal exansion and contraction of iework caused by variations in liquid temerature. Reduction of mechanical influences in connection with ressure surges in the iework. Isolation of structure-borne noise in the iework (only rubber bellows exansion joints). Note: Exansion joints must not be installed to comensate for inaccuracies in the iework such as centre dislacement of flanges. Fit exansion joints at a distance of minimum 1 to 1.5 x DN diameter from the manifold on the suction as well as on the discharge side. This revents the develoment of turbulence in the exansion joints, resulting in better suction conditions and a minimum ressure loss on the ressure side. Electrical installation The electrical installation should be carried out by an authorised erson in accordance with local regulations. The electrical installation of the booster system must be carried out in accordance with enclosure class IP54. Make sure that the booster system is suitable for the ower suly to which it is connected. Make sure that the wire cross-section corresonds to the secifications in the wiring diagram. Note: The mains connection should be carried out as shown in the wiring diagram. TM02 4981 1902 - TM02 4979 1902 Fig. 31 Examles of rubber bellows exansion joints with and without limiting rods Exansion joints with limiting rods can be used to minimise the forces caused by the exansion joints. Exansion joints with limiting rods are always recommended for flanges larger than DN. The ies should be anchored so that they do not stress the exansion joints and the um. Follow the sulier s instructions and ass them on to advisers or ie installers. 23
Sizing ydro MPC Sizing When sizing a booster system, the following must be taken into account: The erformance of the booster system must meet the highest ossible demand both in terms of flow rate and ressure. The booster system must not be oversized. This is imortant in relation to installation and oerating costs. You can size Grundfos ydro MPC booster systems via WinCAPS, WebCAPS or this data booklet. Sizing in WinCAPS or WebCAPS (recommended) We recommend that you size your ydro MPC booster system in WinCAPS or WebCAPS, which are selection rograms offered by Grundfos. For further information, see age 85. WebCAPS or WinCAPS feature a user-friendly and easy-to-use virtual guide which leads you through the selection of the most otimum booster system for the alication in question. TM04 4111 0709 Fig. 32 Sizing in WebCAPS Sizing via this data booklet There are seven stes: 1. Maximum flow requirement 2. Required discharge ressure 3. System layout 4. Consumtion rofile and load rofile 5. Inlet ressure 6. Selection of booster system 7. Accessories. 24
Sizing ydro MPC 1. Maximum flow requirement Total consumtion and maximum flow rate deend on the alication in question. The maximum flow requirement can be calculated by means of the table below which is based on statistical data. Q Consumtion year Q Consumer Unit eriod d day Q(m) day fd ft Max. flow rate m 3 /year days/year m 3 /day m 3 /day m 3 /h Residence building Residence (2.5 ersons) 183 365 0.5 1.3 0.65 1.7 0.046 Office building Emloyee 25 250 0.1 1.2 0.12 3.6 0.018 Shoing centre Emloyee 25 300 0.08 1.2 0.1 4.3 0.018 Suermarket Emloyee 80 300 0.27 1.5 0.4 3.0 0.05 otel Bed 180 365 0.5 1.5 0.75 4.0 0.125 osital Bed 300 365 0.8 1.2 1.0 3.0 0.12 School Puil 8 200 0.04 1.3 0.065 2.5 0.007 Examle: otel with 5 beds Number of beds: n Total annual consumtion: Q year x n Consumtion eriod: d Average consumtion er day: (Q year x n)/d Year maximum consumtion: Q(m) day = fd x Q day Maximum flow requirement er hour: Q max = Max. flow rate/hour x number of beds Calculation n = 5 beds Q year x n = 180 x 5 = 97,200 m 3 /year d = 365 days/year (Q year x n)/d = 97,200/365 = 266.3 m 3 /day Q(m) day = fd x Q day = 1.5 x 266.3 = 399.4 m 3 /day Q max = Max. flow rate/hour x number of beds = 0.125 x 5 = 67.5 m 3 /h. 25
Sizing ydro MPC 2. Required discharge ressure The required discharge ressure, Pset, of the ydro MPC can be calculated with the following equation: P set = P ta(min) + P f + (h max /10.2) ; P boost = P set P in(min). Key P set = Required discharge ressure in bar P ta(min) = Required minimum ressure at the highest taing oint in bar P f = Total ie friction loss in metre h max = eight from booster discharge ort to highest taing oint in metre P in(min) = Min. inlet ressure in bar P boost = Required boost in bar. Pta(min) Calculation P ta(min) = 2 bar P f = 1.2 bar h max = 41.5 metres P in(min) = 2 bar P set = 2+1.2+(41.5/10.2) = 7.3 bar P boost = 7.3-2 = 5.3 bar. 3. System layout What is the system layout? a) Direct boosting (examle: ydro MPC connected to water mains designed to distribute water from one lace to another). b) Break tank (examle: ydro MPC connected to a break tank installed before the booster system). c) Pressure boosting in zones (examle: igh-rise building or hilly landscae where the water suly system is divided into zones). P f h max d) Roof tank (examle: ydro MPC distributes water to a roof tank on to of a high-rise building). 4. Consumtion rofile and load rofile The consumtion attern of the installation can be illustrated as a 24-hour consumtion rofile and a load rofile. 24-hour consumtion rofile The 24-hour consumtion rofile is the relation between the time of the day and the flow rate. Q [ m3 /h ] P in(min) P boost P set TM04 4105 0709 30 20 10 3 6 9 12 15 18 21 24 TM00 9188 1303 Fig. 33 Calculation of required discharge ressure Fig. 34 Examle of 24-hour consumtion rofile Note: If the consumtion is variable and otimum comfort is required, ums with continuously variable seed control should be used. 26
Sizing ydro MPC Load rofile When the 24-hour consumtion rofile has been determined, the load rofile can be made. The load rofile gives an overview of how many er cent er day the booster oerates at a secific flow rate. TM04 4113 0709 Fig. 35 Load rofile Examles of tyical 24-hour consumtion rofiles and their load rofiles: Water suly Industry Irrigation Q Q Q 24-hour rofile h TM00 9197 1705 h TM00 9200 1705 h TM00 9198 1705 Flow rate: ighly variable Flow rate: ighly variable with sudden changes Flow rate: Constant and known Pressure: Constant Pressure: Constant Pressure: Constant Q Q Q Duty-time rofile h% Consumtion is highly variable. Continuously variable seed control of the ums is recommended. TM00 9201 1705 Consumtion is highly variable with sudden changes. Continuously variable seed control of the ums is recommended. TM00 9199 1705 Variations in consumtion are regular, yet known. Simle control is recommended. Recommended tyes: -E and -F Recommended tyes: -E and -F Recommended tyes: -S h% h% TM00 9202 1705 27
Sizing ydro MPC 5. Inlet ressure Is there a ositive inlet ressure? If so, the inlet ressure must be taken into consideration to ensure safe oeration. The values for inlet ressure and oerating ressure must not be considered individually, but must always be comared. Examle A ydro MPC-E booster system with 3 CRIE 20-7 ums has been selected. Maximum oerating ressure: 16 bar. Maximum inlet ressure: 10 bar. Discharge ressure against a closed valve: 10 bar. The selected system is allowed to start at an inlet ressure of maximum 5.8 bar, as the maximum oerating ressure is limited to 16 bar. If the maximum inlet ressure exceeds 5.8 bar, a system rated PN 25 must be selected. 6. Selection of ydro MPC booster system Select the booster system on the basis of these factors. Maximum flow requirement, required discharge ressure, load rofile, number of ums required, ossible standby ums, etc. 7. Accessories aving selected the otimum ydro MPC booster system, you must consider whether accessories as those mentioned below are required. Dry-running rotection Every booster system must be rotected against dry running. The inlet conditions determine the tye of dry-running rotection: Diahragm tank The need for a diahragm tank is estimated on the basis of the following guidelines: Due to the sto function, all ydro MPC booster systems in buildings should be equied with a diahragm tank. Normally, ydro MPC booster systems in watersuly alications require no diahragm tank, as miles of iing artly hold the necessary caacity, artly have the elasticity to give sufficient caacity. Note: To avoid the risk of water hammering, a diahragm tank may be necessary. The need for a diahragm tank for ydro MPC booster systems in industrial alications should be estimated from situation to situation on the basis of the individual factors on site. Note: If the ydro MPC booster system includes ilot ums, the diahragm tank is to be sized according to the caacity of this um. For further information about otional equiment and accessories, see age 75 to 83. Pum tye Recommended diahragm tank size [litres] -E -F -S CRI(E) 3 8 8 80 CRI(E) 5 12 12 120 CRI(E) 10 18 18 180 CRI(E) 15 80 80 300 CRI(E) 20 80 80 0 CR(E) 32 80 80 0 CR(E) 45 120 120 800 CR(E) 64 120 120 0 CR(E) 90 180 180 1500 CR(E) 120 180 180 1500 CR(E) 150 180 180 1500 The size of the obligatory diahragm tank in litres can be calculated from the following equations: If the system draws from a tank or a well, select a level switch or electrode relay for dry-running rotection. If the system has an inlet ressure, select a ressure transmitter or a ressure switch for dryrunning rotection. 28
Sizing ydro MPC ydro MPC-E and -F ydro MPC-S Symbol V 0 k Q Q set Descrition Tank volume [litres] The ratio between nominal flow rate of one um Q nom and the flow rate Q min at which the um is to change to on/off oeration. k Q = Q min /Q nom Mean flow rate, Q nom [m 3 /h] Setoint [bar] k The ratio between the on/off band Δ and the setoint set, k = Δ/ set k f N k Q Q ( set + 1) 2 30 ------------ 10 N V 0 = -------------------------------------------------------------------------------------- 3.6 ( k f set + 1) k set 0 Q ( set + 1) ( k set + set + 1) V 0 = ----------------------------------------------------------------------------------------------------------------- 4 N ( k f set + 1) k set The ratio between tank re-charge ressure 0 and the setoint set k f = 0 / set 0.9 for ydro MPC-S 0.7 for ydro MPC-E and -F Maximum number of starts/stos er hour. ydro MPC-E and -F The tank values are based on the following data: Symbol ydro MPC -E and -F -S Q Q nom of one um Q nom of one um k Q 10 % - set 4 bar 4 bar k 20 % 25 % k f 0.7 0.9 Examle of ydro MPC-E and -S with CRI(E) 20 Symbol ydro MPC-E ydro MPC-S Q [m 3 /h] 10 10 k Q 10 % - k 20 % 25 % set [bar] 4 4 N [h -1 ] 200 Result V 0 [litres] 18.3 163 Selected tank 18 180 Δ [bar] 0.8 1 0 [bar] 2.8 3.6 set + 1/2 Δ set set - 1/2 Δ Q min Δ Q nom Q TM03 3070 0206 ydro MPC-S set + Δ set Δ Q nom Q TM03 3071 0206 29
Sizing ydro MPC Understanding the curve charts The x-axis showing the flow rate (Q) in m 3 /h is common to all the curves; the y-axis showing the head () in metres has been adated to the individual um tye. 10 1200 0 1 120 ydro MPC CRI(E) 5-20 50 z ISO 9906 Annex A 800 80 0 0 120 1 2 3 4 Secification of booster system, um tye, frequency and of the standard to which the Q-curves corresond. CRI(E) 5-16 0 800 80 The y-axis is adated to the individual um tye. 0 0 200 0 500 0 300 200 500 0 300 200 0 300 200 20 50 30 20 50 30 20 10 30 20 Secification of system erformance based on the number of ums in oeration: 1 = one um in oeration 2 = two ums in oeration 3 = three ums in oeration. CRI(E) 5-10 CRI(E) 5-8 CRI(E) 5-5 10 1 2 3 4 0 300 0 30 CRI(E) 5-4 200 20 0 10 0 1 2 3 4 0 4 8 12 16 20 24 28 32 36 44 48 Q [m³/h] 0 2 4 6 8 10 12 14 Q [l/s] The x-axis is common to all um tyes. TM03 0990 2009 30
Sizing ydro MPC Examle: ow to select a system A flow rate of 67.5 m 3 /h is required. A head of 73 metres is required. Now draw a vertical line from the secified flow rate. Draw a horizontal line from the head required. The intersection of the two lines gives the number of ums required for the system (3 CRI(E) 20-7). The um tye best meeting this secification is found by means of the y-axis, for instance 3 CRI(E) 20-7. Only booster systems with erformance ranges within the hatched area in the examle should be selected. 0 900 90 ydro MPC CRI(E) 20-7 50 z ISO 9906 Annex A 800 80 700 70 0 500 50 0 300 30 0 10 20 30 50 70 80 90 110 120 130 1 150 1 Q [m³/h] 0 5 10 15 20 25 30 35 45 Q [l/s] TM03 1153 2009 31
Curve conditions ydro MPC ow to read the curve charts The guidelines below aly to the curves shown on the following ages: 1. The curves show the um mean values. 2. The curves should not be used as guarantee curves. 3. Measurements were made with ure water at a temerature of +20 C. 4. The curves aly to a kinematic viscosity of υ =1mm 2 /s (1 cst). 32
Curve charts ydro MPC with CRI(E) 3 ydro MPC with CRI(E) 3 1200 0 1 120 ydro MPC CRI(E) 3-23 50 z ISO 9906 Annex A 800 80 0 0 120 1 2 3 CRI(E) 3-19 0 800 80 0 0 1 2 3 4 200 0 20 CRI(E) 3-15 800 80 0 0 200 0 0 200 0 500 0 300 20 20 0 50 30 CRI(E) 3-10 CRI(E) 3-7 200 0 20 10 1 2 3 4 5 6 CRI(E) 3-5 300 30 200 20 0 10 0 1 2 3 4 5 6 0 2 4 6 8 10 12 14 16 18 20 22 24 26 Q [m³/h] 0 7 Q [l/s] TM03 0989 3806 33
Curve charts ydro MPC with CRI(E) 5 ydro MPC with CRI(E) 5 10 1200 0 1 120 ydro MPC CRI(E) 5-20 50 z ISO 9906 Annex A 800 80 0 0 120 1 2 3 4 CRI(E) 5-16 0 800 80 0 0 200 0 500 0 300 200 500 0 300 200 0 300 200 20 50 30 20 50 30 20 10 30 20 CRI(E) 5-10 CRI(E) 5-8 CRI(E) 5-5 10 1 2 3 4 0 300 0 30 CRI(E) 5-4 200 20 0 10 0 1 2 3 4 0 4 8 12 16 20 24 28 32 36 44 48 Q [m³/h] 0 2 4 6 8 10 12 14 Q [l/s] TM03 0990 2009 34
Curve charts ydro MPC with CRI(E) 10 ydro MPC with CRI(E) 10 1200 0 120 ydro MPC CRI(E) 10-12 50 z ISO 9906 Annex A 800 80 0 0 CRI(E) 10-9 800 80 0 0 800 80 CRI(E) 10-6 0 0 200 0 20 CRI(E) 10-4 300 30 200 20 300 10 30 CRI(E) 10-3 250 25 200 20 150 15 1 2 3 4 10 0 5 10 15 20 25 30 35 45 50 55 65 70 75 Q [m³/h] 0 2 4 6 8 10 12 14 16 18 20 Q [l/s] TM03 0991 2009 35
Curve charts ydro MPC with CRI(E) 15 ydro MPC with CRI(E) 15 1200 0 120 ydro MPC CRI(E) 15-9 50 z ISO 9906 Annex A 800 80 0 0 CRI(E) 15-7 800 80 0 0 800 80 CRI(E) 15-5 0 0 200 0 20 CRI(E) 15-3 300 30 200 20 300 10 30 CRI(E) 15-2 250 25 200 20 150 15 10 0 10 20 30 50 70 80 90 110 120 130 1 Q [m³/h] 0 5 10 15 20 25 30 35 Q [l/s] TM03 1066 2009 36
Curve charts ydro MPC with CRI(E) 20 ydro MPC with CRI(E) 20 1300 1200 1 0 900 1 130 120 110 90 ydro MPC CRI(E) 20-10 50 z ISO 9906 Annex A 800 700 80 70 CRI(E) 20-7 900 90 800 80 700 70 0 500 0 50 80 CRI(E) 20-5 700 70 0 500 50 0 300 30 50 CRI(E) 20-3 0 300 30 200 20 10 30 CRI(E) 20-2 250 25 200 20 150 15 10 0 10 20 30 50 70 80 90 110 120 130 1 150 1 Q [m³/h] 0 5 10 15 20 25 30 35 45 Q [l/s] TM03 1067 2009 37
Curve charts ydro MPC with CR(E) 32 ydro MPC with CR(E) 32 10 10 1 1 ydro MPC CR(E) 32-8 50 z ISO 9906 Annex A 1200 120 0 800 80 0 1200 120 CR(E) 32-6 0 800 80 0 0 800 80 CR(E) 32-4 0 0 200 0 20 CR(E) 32-3 500 50 0 300 200 0 30 20 CR(E) 32-2 300 30 200 20 10 0 20 80 120 1 1 180 200 220 Q [m³/h] 0 10 20 30 50 Q [l/s] TM03 1068 2009 38
Curve charts ydro MPC with CR(E) 45 ydro MPC with CR(E) 45 10 10 180 1 1 ydro MPC CR(E) 45-6 50 z ISO 9906 Annex A 1200 120 0 800 10 80 1 CR(E) 45-5 1200 120 0 800 0 0 80 CR(E) 45-4 800 80 0 0 800 80 CR(E) 45-3 0 0 200 500 20 50 CR(E) 45-2 0 300 200 30 20 500 10 50 CR(E) 45-2-2 0 300 30 200 20 10 0 20 80 120 1 1 180 200 220 2 2 280 300 320 Q [m³/h] 0 10 20 30 50 70 80 90 Q [l/s] TM03 1069 2009 39
Curve charts ydro MPC with CR(E) 64 ydro MPC with CR(E) 64 10 1200 0 800 0 800 0 0 0 800 0 0 800 0 1 120 80 120 80 80 80 ydro MPC CR(E) 64-5-1 50 z ISO 9906 Annex A CR(E) 64-4 CR(E) 64-4-2 CR(E) 64-3-1 0 200 0 20 CR(E) 64-2 0 200 0 300 200 300 20 30 20 10 30 CR(E) 64-2-2 CR(E) 64-1 200 20 10 1 2 3 4 5 6 0 0 0 80 120 1 200 2 280 320 3 0 4 480 520 Q [m³/h] 0 20 80 120 1 Q [l/s] TM03 1070 3806
Curve charts ydro MPC with CR(E) 90 ydro MPC with CR(E) 90 2000 10 1200 800 0 1200 0 800 0 0 0 800 0 0 200 800 0 0 200 800 0 200 1 120 80 120 80 80 20 80 20 80 ydro MPC CR(E) 90-5-2 50 z ISO 9906 Annex A 1 2 3 4 5 6 CR(E) 90-4 CR(E) 90-4-2 CR(E) 90-3 CR(E) 90-3-2 0 200 0 20 1 2 3 4 5 6 CR(E) 90-2 0 200 0 20 CR(E) 90-2-2 200 20 0 0 0 50 150 200 250 300 350 0 450 500 550 0 650 700 Q [m³/h] 0 20 80 120 1 1 180 200 Q [l/s] TM03 1143 2009 41
Curve charts ydro MPC with CR(E) 120 ydro MPC with CR(E) 120 10 1200 1 120 ydro MPC CR(E) 120-5-1 50 z ISO 9906 Annex A 0 800 80 0 0 900 CR(E) 120-4-1 800 700 80 0 500 0 90 CR(E) 120-3 800 80 700 70 0 500 50 0 300 0 30 CR(E) 120-2 500 50 0 300 200 500 30 20 50 CR(E) 120-2-1 0 300 30 200 20 10 0 200 300 0 500 0 700 800 Q [m³/h] 0 50 150 200 250 Q [l/s] TM04 4774 2009 42
Curve charts ydro MPC with CR(E) 150 ydro MPC with CR(E) 150 10 1200 1 120 ydro MPC CR(E) 150-5-2 50 z ISO 9906 Annex A 0 800 0 1200 80 120 CR(E) 150-4-1 0 800 80 0 0 CR(E) 150-3 900 90 800 80 700 70 0 500 700 50 70 CR(E) 150-3-2 0 500 50 0 300 500 30 50 CR(E) 150-2-1 0 300 30 200 20 0 200 300 0 500 0 700 800 900 0 Q [m³/h] 0 50 150 200 250 300 Q [l/s] TM04 4775 2009 43
Technical data ydro MPC with CRI(E) 3 / CRI(E) 5 ydro MPC with CRI(E) 3 / CRI(E) 5 Fig. 36 Dimensional sketch of a ydro MPC booster system with a control cabinet mounted on the same base frame as the ums (design A) Fig. 37 Dimensional sketch of a ydro MPC booster system with a control cabinet centred on the base frame (design B) TM03 3042 2410 TM03 1181 2310 TM03 17 2310 Fig. 38 Dimensional sketch of a ydro MPC booster system with a floor-mounted control cabinet (design C) 44
Technical data ydro MPC with CRI(E) 3 / CRI(E) 5 Electrical data, dimensions and weights ydro MPC-E with CRIE 3 No. of ums Pum tye 2 3 4 ydro MPC-F with CRI 3 No. of ums Pum tye 2 3 4 Suly voltage [V] Motor [kw] Max. I N [A] Max. I O [A] Connection W L1 1 2 Suly voltage U1: 3 x 380-415 V, ± 10 %, N, PE. Suly voltage U2: 3 x 380-415 V, ± 5 %, PE. Design A: ydro MPC booster system with a control cabinet mounted on the same base frame as the ums. Design C: ydro MPC booster system with a floor-mounted control cabinet. Maximum current in neutral conductor, Max. I 0 [A], alies to booster systems with single-hase motors. Dimensions may vary by ± 10 mm. 3 Weight Design [kg] CRIE3-5 U1 0.37 3.8 2.7 R 2 714 1050 551 120 1455 A CRIE3-5 U1 0.37 3.8 2.7 R 2 714 1050 551 120 1455 A CRIE3-7 U1 0.55 6.1 3.9 R 2 714 1050 645 120 1455 103 A CRIE3-10 U1 0.75 7.2 5.1 R 2 714 1050 690 120 1455 113 A CRIE3-15 U1 1.1 10.5 7.4 R 2 714 1050 827 120 1455 116 A CRIE3-19 U2 1.5 6.8 - R 2 714 1050 9 120 1455 147 A CRIE3-23 U2 2.2 9.5 - R 2 714 1050 1052 120 1455 154 A CRIE3-5 U1 0.37 4.7 2.7 R 2 714 1370 551 120 1455 156 A CRIE3-7 U1 0.55 7.4 3.9 R 2 714 1370 645 120 1455 1 A CRIE3-10 U1 0.75 8.8 5.1 R 2 714 1370 690 120 1455 175 A CRIE3-15 U1 1.1 12.8 7.4 R 2 714 1370 827 120 1455 179 A CRIE3-19 U2 1.5 10.2 - R 2 714 1370 9 120 1455 224 A CRIE3-23 U2 2.2 14.3 - R 2 714 1370 1052 120 1455 235 A CRIE3-5 U1 0.37 5.4 5.4 R 2 1/2 730 1690 551 120 1455 200 A CRIE3-7 U1 0.55 8.6 7.8 R 2 1/2 730 1690 645 120 1455 206 A CRIE3-10 U1 0.75 10.2 10.2 R 2 1/2 730 1690 690 120 1455 225 A CRIE3-15 U1 1.1 14.8 14.8 R 2 1/2 730 1690 827 120 1455 232 A CRIE3-19 U2 1.5 13.6 - R 2 1/2 730 1690 9 120 1455 291 A CRIE3-23 U2 2.2 19 - R 2 1/2 730 1690 1052 120 1455 306 A Suly voltage [V] Motor [kw] Max. I N [A] Connection W L1 L2 1 2 3 Weight Design [kg] CRI3-7 U2 0.55 2.9 R 2 714 610 800 587 120 1500 169 C CRI3-10 U2 0.75 3.8 R 2 714 610 800 690 120 1500 179 C CRI3-15 U2 1.1 5.2 R 2 714 610 800 777 120 1500 182 C CRI3-19 U2 1.5 6.8 R 2 714 610 800 915 120 1500 196 C CRI3-23 U2 2.2 9.5 R 2 714 610 800 987 120 1500 203 C CRI3-7 U2 0.55 4.3 R 2 714 930 800 587 120 1500 214 C CRI3-10 U2 0.75 5.7 R 2 714 930 800 690 120 1500 229 C CRI3-15 U2 1.1 7.8 R 2 714 930 800 777 120 1500 234 C CRI3-19 U2 1.5 10.2 R 2 714 930 800 915 120 1500 255 C CRI3-23 U2 2.2 14.3 R 2 714 930 800 987 120 1500 266 C CRI3-7 U2 0.55 5.8 R 2 1/2 730 1250 800 587 120 1500 258 C CRI3-10 U2 0.75 7.6 R 2 1/2 730 1250 800 690 120 1500 279 C CRI3-15 U2 1.1 10.4 R 2 1/2 730 1250 800 777 120 1500 284 C CRI3-19 U2 1.5 13.6 R 2 1/2 730 1250 800 915 120 1500 313 C CRI3-23 U2 2.2 19 R 2 1/2 730 1250 800 987 120 1500 328 C 45
Technical data ydro MPC with CRI(E) 3 / CRI(E) 5 ydro MPC-S with CRI 3 No. of ums Pum tye 2 3 4 Suly voltage [V] ydro MPC-E with CRIE 5 No. of ums Pum tye 2 3 4 Motor [kw] Max. I N [A] Connection W L1 1 2 3 Weight Design [kg] CRI3-5 U2 0.37 2 R 2 714 720 551 120 12 102 B CRI3-7 U2 0.55 2.9 R 2 714 720 587 120 12 105 B CRI3-10 U2 0.75 3.8 R 2 714 720 690 120 12 115 B CRI3-15 U2 1.1 5.2 R 2 714 720 777 120 12 118 B CRI3-19 U2 1.5 6.8 R 2 714 720 915 120 12 132 B CRI3-23 U2 2.2 9.5 R 2 714 720 987 120 12 139 B CRI3-5 U2 0.37 3 R 2 714 1570 551 120 1455 164 A CRI3-7 U2 0.55 4.3 R 2 714 1570 587 120 1455 168 A CRI3-10 U2 0.75 5.7 R 2 714 1570 690 120 1455 184 A CRI3-15 U2 1.1 7.8 R 2 714 1570 777 120 1455 188 A CRI3-19 U2 1.5 10.2 R 2 714 1570 915 120 1455 209 A CRI3-23 U2 2.2 14.3 R 2 714 1570 987 120 1455 220 A CRI3-5 U2 0.37 4 R 2 1/2 730 1890 551 120 1455 207 A CRI3-7 U2 0.55 5.8 R 2 1/2 730 1890 587 120 1455 212 A CRI3-10 U2 0.75 7.6 R 2 1/2 730 1890 690 120 1455 232 A CRI3-15 U2 1.1 10.4 R 2 1/2 730 1890 777 120 1455 238 A CRI3-19 U2 1.5 13.6 R 2 1/2 730 1890 915 120 1455 267 A CRI3-23 U2 2.2 19 R 2 1/2 730 1890 987 120 1455 281 A Suly voltage [V] Motor [kw] Max. I N [A] Max. I O [A] Connection W L1 1 2 Suly voltage U1: 3 x 380-415 V, ± 10 %, N, PE. Suly voltage U2: 3 x 380-415 V, ± 5 %, PE. Design A: ydro MPC booster system with a control cabinet mounted on the same base frame as the ums. Design C: ydro MPC booster system with a floor-mounted control cabinet. Maximum current in neutral conductor, Max. I 0 [A], alies to booster systems with single-hase motors. Dimensions may vary by ± 10 mm. 3 Weight Design [kg] CRIE5-4 U1 0.55 6.1 3.9 R 2 714 1050 572 120 1455 105 A CRIE5-5 U1 0.75 7.2 5.1 R 2 714 1050 634 120 1455 110 A CRIE5-8 U1 1.1 10.5 7.4 R 2 714 1050 726 120 1455 118 A CRIE5-10 U2 1.5 6.8 - R 2 714 1050 846 120 1455 145 A CRIE5-16 U2 2.2 9.5 - R 2 714 1050 1070 120 1455 155 A CRIE5-20 U2 3 12.4 - R 2 714 1050 1175 120 1455 173 A CRIE5-4 U1 0.55 7.4 3.9 R 2 714 1370 572 120 1455 163 A CRIE5-5 U1 0.75 8.8 5.1 R 2 714 1370 634 120 1455 170 A CRIE5-8 U1 1.1 12.8 7.4 R 2 714 1370 726 120 1455 183 A CRIE5-10 U2 1.5 10.2 - R 2 714 1370 846 120 1455 221 A CRIE5-16 U2 2.2 14.3 - R 2 714 1370 1070 120 1455 236 A CRIE5-20 U2 3 18.6 - R 2 714 1370 1175 120 1455 264 A CRIE5-4 U1 0.55 8.6 7.8 R 2 1/2 730 1690 572 120 1455 209 A CRIE5-5 U1 0.75 10.2 10.2 R 2 1/2 730 1690 634 120 1455 219 A CRIE5-8 U1 1.1 14.8 14.8 R 2 1/2 730 1690 726 120 1455 236 A CRIE5-10 U2 1.5 13.6 - R 2 1/2 730 1690 846 120 1455 287 A CRIE5-16 U2 2.2 19 - R 2 1/2 730 1690 1070 120 1455 307 A CRIE5-20 U2 3 25 - R 2 1/2 730 1690 1175 120 1455 344 A 46
Technical data ydro MPC with CRI(E) 3 / CRI(E) 5 ydro MPC-F with CRI 5 No. of ums Pum tye 2 3 4 ydro MPC-S with CRI 5 No. of ums Pum tye 2 3 4 Suly voltage [V] Motor [kw] Max. I N [A] Connection W L1 L2 1 2 Suly voltage U2: 3 x 380-415 V, ± 5 %, PE. Design A: ydro MPC booster system with a control cabinet mounted on the same base frame as the ums. Design B: ydro MPC booster system with a control cabinet centred on the base frame. Design C: ydro MPC booster system with a floor-mounted control cabinet. Maximum current in neutral conductor, Max. I 0 [A], alies to booster systems with single-hase motors. Dimensions may vary by ± 10 mm. 3 Weight Design [kg] CRI5-4 U2 0.55 2.9 R 2 714 610 800 572 120 1500 171 C CRI5-5 U2 0.75 3.8 R 2 714 610 800 642 120 1500 173 C CRI5-8 U2 1.1 5.2 R 2 714 610 800 726 120 1500 184 C CRI5-10 U2 1.5 6.8 R 2 714 610 800 846 120 1500 200 C CRI5-16 U2 2.2 9.5 R 2 714 610 800 5 120 1500 204 C CRI5-20 U2 3 12.8 R 2 714 610 800 1175 120 1500 222 C CRI5-4 U2 0.55 4.3 R 2 714 930 800 572 120 1500 217 C CRI5-5 U2 0.75 5.7 R 2 714 930 800 642 120 1500 221 C CRI5-8 U2 1.1 7.8 R 2 714 930 800 726 120 1500 237 C CRI5-10 U2 1.5 10.2 R 2 714 930 800 846 120 1500 2 C CRI5-16 U2 2.2 14.3 R 2 714 930 800 5 120 1500 267 C CRI5-20 U2 3 19.2 R 2 714 930 800 1175 120 1500 294 C CRI5-4 U2 0.55 5.8 R 2 1/2 730 1250 800 572 120 1500 262 C CRI5-5 U2 0.75 7.6 R 2 1/2 730 1250 800 642 120 1500 267 C CRI5-8 U2 1.1 10.4 R 2 1/2 730 1250 800 726 120 1500 289 C CRI5-10 U2 1.5 13.6 R 2 1/2 730 1250 800 846 120 1500 320 C CRI5-16 U2 2.2 19 R 2 1/2 730 1250 800 5 120 1500 330 C CRI5-20 U2 3 26 R 2 1/2 730 1250 800 1175 120 1500 366 C Suly voltage [V] Motor [kw] Max. I N [A] Connection W L1 1 2 3 Weight Design [kg] CRI5-4 U2 0.55 2.9 R 2 714 720 572 120 12 107 B CRI5-5 U2 0.75 3.8 R 2 714 720 642 120 12 109 B CRI5-8 U2 1.1 5.2 R 2 714 720 726 120 12 120 B CRI5-10 U2 1.5 6.8 R 2 714 720 846 120 12 136 B CRI5-16 U2 2.2 9.5 R 2 714 720 5 120 12 1 B CRI5-20 U2 3 12.8 R 2 714 720 1175 120 12 158 B CRI5-4 U2 0.55 4.3 R 2 714 1570 572 120 1455 171 A CRI5-5 U2 0.75 5.7 R 2 714 1570 642 120 1455 175 A CRI5-8 U2 1.1 7.8 R 2 714 1570 726 120 1455 191 A CRI5-10 U2 1.5 10.2 R 2 714 1570 846 120 1455 214 A CRI5-16 U2 2.2 14.3 R 2 714 1570 5 120 1455 221 A CRI5-20 U2 3 19.2 R 2 714 1570 1175 120 1455 248 A CRI5-4 U2 0.55 5.8 R 2 1/2 730 1890 572 120 1455 216 A CRI5-5 U2 0.75 7.6 R 2 1/2 730 1890 642 120 1455 221 A CRI5-8 U2 1.1 10.4 R 2 1/2 730 1890 726 120 1455 243 A CRI5-10 U2 1.5 13.6 R 2 1/2 730 1890 846 120 1455 274 A CRI5-16 U2 2.2 19 R 2 1/2 730 1890 5 120 1455 283 A CRI5-20 U2 3 26 R 2 1/2 730 1890 1175 120 1455 319 A 47
Technical data ydro MPC with CRI(E) 10 ydro MPC with CRI(E) 10 Note: The manifold connection is either R thread or DIN flange. For further details, see the relevant table on age 50 or 51. Fig. 39 Dimensional sketch of a ydro MPC booster system with a control cabinet mounted on the same base frame as the ums (design A) TM03 1183 2310 TM03 1182 2310 Fig. Dimensional sketch of a ydro MPC booster system with a control cabinet centred on the base frame (design B) 48
Technical data ydro MPC with CRI(E) 10 Fig. 41 Dimensional sketch of a ydro MPC booster system with a floor-mounted control cabinet (design C) TM04 7830 2410 TM04 7829 2410 Fig. 42 Dimensional sketch of a ydro MPC booster system with a control cabinet mounted on a searate base frame (design D) 49
Technical data ydro MPC with CRI(E) 10 Electrical data, dimensions and weights ydro MPC-E with CRIE 10 No. of ums Pum tye 2 3 4 5 6 ydro MPC-F with CRI 10 No. of ums Pum tye 2 3 4 5 6 Suly voltage Motor [V] [kw] Max. I N [A] Max. I O [A] Connection W L1 L2 1 2 3 Weight Design [kg] CRIE10-3 U1 1.1 10.5 7.4 R 2 1/2 880 1080-688 150 1455 145 A CRIE10-4 U2 1.5 6.8 - R 2 1/2 880 1080-783 150 1455 178 A CRIE10-6 U2 2.2 9.5 - R 2 1/2 880 1080-884 150 1455 186 A CRIE10-9 U2 3 12.4 - R 2 1/2 880 1080-992 150 1455 202 A CRIE10-12 U2 4 16 - R 2 1/2 880 1080-1119 150 1455 228 A CRIE10-3 U1 1.1 12.8 7.4 R 2 1/2 880 10-688 150 1455 223 A CRIE10-4 U2 1.5 10.2 - R 2 1/2 880 10-783 150 1455 271 A CRIE10-6 U2 2.2 14.3 - R 2 1/2 880 10-884 150 1455 283 A CRIE10-9 U2 3 18.6 - R 2 1/2 880 10-992 150 1455 307 A CRIE10-12 U2 4 24 - R 2 1/2 880 10-1119 150 1455 347 A CRIE10-3 U1 1.1 14.8 14.8 DN 80 4 1720-688 150 1455 299 A CRIE10-4 U2 1.5 13.6 - DN 80 4 1720-783 150 1455 364 A CRIE10-6 U2 2.2 19 - DN 80 4 1720-884 150 1455 380 A CRIE10-9 U2 3 25 - DN 80 4 1720-992 150 1455 412 A CRIE10-12 U2 4 32 - DN 80 4 1720-1119 150 1455 465 A CRIE10-3 U1 1.1 16.5 14.8 DN 80 4 16 380 688 150 1455 341 D CRIE10-4 U2 1.5 17 - DN 80 4 16 380 783 150 1455 420 D CRIE10-6 U2 2.2 24 - DN 80 4 16 380 884 150 1455 441 D CRIE10-9 U2 3 31 - DN 80 4 16 380 992 150 1455 481 D CRIE10-12 U2 4 - DN 80 4 16 380 1119 150 1455 547 D CRIE10-3 U1 1.1 18.1 14.8 DN 1024 2102 380 688 150 1455 5 D CRIE10-4 U2 1.5 20 - DN 1024 2102 0 783 150 1455 511 D CRIE10-6 U2 2.2 29 - DN 1024 2102 0 884 150 1455 535 D CRIE10-9 U2 3 37 - DN 1024 2102 0 992 150 1455 584 D CRIE10-12 U2 4 48 - DN 1024 2102 0 1119 150 1455 664 D Suly voltage [V] Motor [kw] Max. I N [A] Connection W L1 L2 1 2 3 Weight Design [kg] CRI10-3 U2 1.1 5.2 R 2 1/2 880 670 800 688 150 1500 212 C CRI10-4 U2 1.5 6.8 R 2 1/2 880 670 800 784 150 1500 224 C CRI10-6 U2 2.2 9.5 R 2 1/2 880 670 800 844 150 1500 232 C CRI10-9 U2 3 12.8 R 2 1/2 880 670 800 993 150 1500 249 C CRI10-12 U2 4 16 R 2 1/2 880 670 800 1120 150 1500 278 C CRI10-3 U2 1.1 7.8 R 2 1/2 880 990 800 688 150 1500 279 C CRI10-4 U2 1.5 10.2 R 2 1/2 880 990 800 784 150 1500 297 C CRI10-6 U2 2.2 14.3 R 2 1/2 880 990 800 844 150 1500 309 C CRI10-9 U2 3 19.2 R 2 1/2 880 990 800 993 150 1500 334 C CRI10-12 U2 4 24 R 2 1/2 880 990 800 1120 150 1500 376 C CRI10-3 U2 1.1 10.4 DN 80 4 1320 800 688 150 1500 355 C CRI10-4 U2 1.5 13.6 DN 80 4 1320 800 784 150 1500 379 C CRI10-6 U2 2.2 19 DN 80 4 1320 800 844 150 1500 396 C CRI10-9 U2 3 26 DN 80 4 1320 800 993 150 1500 430 C CRI10-12 U2 4 32 DN 80 4 1320 800 1120 150 1500 486 C CRI10-3 U2 1.1 13 DN 80 4 16 800 688 150 1500 5 C CRI10-4 U2 1.5 17 DN 80 4 16 800 784 150 1500 435 C CRI10-6 U2 2.2 24 DN 80 4 16 800 844 150 1500 457 C CRI10-9 U2 3 32 DN 80 4 16 800 993 150 1500 498 C CRI10-12 U2 4 DN 80 4 16 800 1120 150 1500 571 C CRI10-3 U2 1.1 15.6 DN 1024 2102 800 688 150 1500 471 C CRI10-4 U2 1.5 20 DN 1024 2102 800 784 150 1500 507 C CRI10-6 U2 2.2 29 DN 1024 2102 800 844 150 1500 531 C CRI10-9 U2 3 38 DN 1024 2102 800 993 150 1500 583 C CRI10-12 U2 4 48 DN 1024 2102 800 1120 150 1500 667 C 50
Technical data ydro MPC with CRI(E) 10 ydro MPC-S with CRI 10 No. of ums Pum tye 2 3 4 5 6 Suly voltage [V] Motor [kw] Max. I N [A] Connection W L1 L2 1 2 Suly voltage U1: 3 x 380-415 V, ± 10 %, N, PE. Suly voltage U2: 3 x 380-415 V, ± 5 %, PE. Design A: ydro MPC booster system with a control cabinet mounted on the same base frame as the ums. Design B: ydro MPC booster system with a control cabinet centred on the base frame. Design C: ydro MPC booster system with a floor-mounted control cabinet. Design D: ydro MPC booster system with a control cabinet mounted on a searate base frame. Maximum current in neutral conductor, Max. I 0 [A], alies to booster systems with single-hase motors. Dimensions may vary by ± 10 mm. 3 Weight Design [kg] CRI10-3 U2 1.1 5.2 R 2 1/2 880 750-688 150 12 148 B CRI10-4 U2 1.5 6.8 R 2 1/2 880 750-784 150 12 1 B CRI10-6 U2 2.2 9.5 R 2 1/2 880 750-844 150 12 168 B CRI10-9 U2 3 12.8 R 2 1/2 880 750-993 150 12 185 B CRI10-12 U2 4 16 R 2 1/2 880 750-1120 150 12 213 B CRI10-3 U2 1.1 7.8 R 2 1/2 880 10-688 150 1455 233 A CRI10-4 U2 1.5 10.2 R 2 1/2 880 10-784 150 1455 251 A CRI10-6 U2 2.2 14.3 R 2 1/2 880 10-844 150 1455 263 A CRI10-9 U2 3 19.2 R 2 1/2 880 10-993 150 1455 288 A CRI10-12 U2 4 24 R 2 1/2 880 10-1120 150 1455 330 A CRI10-3 U2 1.1 10.4 DN 80 4 1920-688 150 1455 309 A CRI10-4 U2 1.5 13.6 DN 80 4 1920-784 150 1455 333 A CRI10-6 U2 2.2 19 DN 80 4 1920-844 150 1455 349 A CRI10-9 U2 3 26 DN 80 4 1920-993 150 1455 382 A CRI10-12 U2 4 32 DN 80 4 1920-1120 150 1455 438 A CRI10-3 U2 1.1 13 DN 80 4 16 0 688 150 1455 350 D CRI10-4 U2 1.5 17 DN 80 4 16 0 784 150 1455 380 D CRI10-6 U2 2.2 24 DN 80 4 16 0 844 150 1455 0 D CRI10-9 U2 3 32 DN 80 4 16 0 993 150 1455 442 D CRI10-12 U2 4 DN 80 4 16 0 1120 150 1455 512 D CRI10-3 U2 1.1 15.6 DN 1024 2102 0 688 150 1455 411 D CRI10-4 U2 1.5 20 DN 1024 2102 0 784 150 1455 447 D CRI10-6 U2 2.2 29 DN 1024 2102 0 844 150 1455 471 D CRI10-9 U2 3 38 DN 1024 2102 0 993 150 1455 522 D CRI10-12 U2 4 48 DN 1024 2102 0 1120 150 1455 6 D 51
Technical data ydro MPC with CRI(E) 15 / CRI(E) 20 ydro MPC with CRI(E) 15 / CRI(E) 20 Fig. 43 Dimensional sketch of a ydro MPC booster system with a control cabinet mounted on the same base frame as the ums (design A) Fig. 44 Dimensional sketch of a ydro MPC booster system with a control cabinet centred on the base frame (design B) TM03 3045 0106 TM04 7831 2410 TM03 1184 2310 Fig. 45 Dimensional sketch of a ydro MPC booster system with a floor-mounted control cabinet (design C) 52
Technical data ydro MPC with CRI(E) 15 / CRI(E) 20 TM04 7832 2410 Fig. 46 Dimensional sketch of a ydro MPC booster system with a control cabinet mounted on a searate base frame (design D) 53
Technical data ydro MPC with CRI(E) 15 / CRI(E) 20 Electrical data, dimensions and weights ydro MPC-E with CRIE 15 No. of ums Pum tye 2 3 4 5 6 ydro MPC-F with CRI 15 No. of ums Pum tye 2 3 4 5 6 Suly voltage [V] Motor [kw] Max. I N [A] Connection W L1 L2 1 2 3 Weight Design [kg] CRIE15-2 U2 2.2 9.5 DN 80 1150 1110-803 1 1455 204 A CRIE15-3 U2 3 12.4 DN 80 1150 1110-867 1 1455 214 A CRIE15-5 U2 4 16 DN 80 1150 1110-995 1 1455 244 A CRIE15-7 U2 5.5 22 DN 80 1150 1110-1135 1 1455 292 A CRIE15-9 U2 7.5 30 DN 80 1150 1110-1213 1 1455 304 A CRIE15-2 U2 2.2 14.3 DN 1170 1430-803 1 1455 314 A CRIE15-3 U2 3 18.6 DN 1170 1430-867 1 1455 329 A CRIE15-5 U2 4 24 DN 1170 1430-995 1 1455 375 A CRIE15-7 U2 5.5 33 DN 1170 1430-1135 1 1455 444 A CRIE15-9 U2 7.5 45 DN 1170 1430-1213 1 1455 463 A CRIE15-2 U2 2.2 19 DN 1170 1750-803 1 1455 393 A CRIE15-3 U2 3 25 DN 1170 1750-867 1 1455 413 A CRIE15-5 U2 4 32 DN 1170 1750-995 1 1455 474 A CRIE15-7 U2 5.5 44 DN 1170 1750-1135 1 1455 566 A CRIE15-9 U2 7.5 DN 1170 1750-1213 1 1455 590 A CRIE15-2 U2 2.2 24 DN 150 1235 1704 380 803 1 1455 504 D CRIE15-3 U2 3 31 DN 150 1235 1704 380 867 1 1455 530 D CRIE15-5 U2 4 DN 150 1235 1704 380 995 1 1455 6 D CRIE15-7 U2 5.5 55 DN 150 1235 1704 380 1135 1 1455 722 D CRIE15-9 U2 7.5 75 DN 150 1235 1704 0 1213 1 1455 765 D CRIE15-2 U2 2.2 29 DN 150 1235 19 0 803 1 1455 3 D CRIE15-3 U2 3 37 DN 150 1235 19 0 867 1 1455 633 D CRIE15-5 U2 4 48 DN 150 1235 19 0 995 1 1455 726 D CRIE15-7 U2 5.5 66 DN 150 1235 19 0 1135 1 1455 865 D CRIE15-9 U2 7.5 90 DN 150 1235 19 0 1213 1 1455 901 D Suly voltage [V] Motor [kw] Max. I N [A] Connection W L1 L2 1 2 3 Weight Design [kg] CRI15-2 U2 2.2 9.5 DN 80 1150 7 800 764 1 1500 254 C CRI15-3 U2 3 12.8 DN 80 1150 7 800 1068 1 1500 265 C CRI15-5 U2 4 16 DN 80 1150 7 800 995 1 1500 294 C CRI15-7 U2 5.5 22 DN 80 1150 7 800 1136 1 1500 348 C CRI15-9 U2 7.5 30 DN 80 1150 7 800 1214 1 1500 384 C CRI15-2 U2 2.2 14.3 DN 1170 1062 800 764 1 1500 346 C CRI15-3 U2 3 19.2 DN 1170 1062 800 1068 1 1500 362 C CRI15-5 U2 4 24 DN 1170 1062 800 995 1 1500 4 C CRI15-7 U2 5.5 34 DN 1170 1062 800 1136 1 1500 481 C CRI15-9 U2 7.5 46 DN 1170 1062 800 1214 1 1500 536 C CRI15-2 U2 2.2 19 DN 1170 1382 800 764 1 1500 417 C CRI15-3 U2 3 26 DN 1170 1382 800 1068 1 1500 439 C CRI15-5 U2 4 32 DN 1170 1382 800 995 1 1500 495 C CRI15-7 U2 5.5 45 DN 1170 1382 800 1136 1 1500 596 C CRI15-9 U2 7.5 61 DN 1170 1382 800 1214 1 1500 668 C CRI15-2 U2 2.2 24 DN 150 1235 1704 800 764 1 1500 531 C CRI15-3 U2 3 32 DN 150 1235 1704 800 1068 1 1500 558 C CRI15-5 U2 4 DN 150 1235 1704 800 995 1 1500 630 C CRI15-7 U2 5.5 56 DN 150 1235 1704 800 1136 1 1500 756 C CRI15-9 U2 7.5 76 DN 150 1235 1704 800 1214 1 1500 847 C CRI15-2 U2 2.2 29 DN 150 1235 19 800 764 1 1500 611 C CRI15-3 U2 3 38 DN 150 1235 19 800 1068 1 1500 644 C CRI15-5 U2 4 48 DN 150 1235 19 800 995 1 1500 728 C CRI15-7 U2 5.5 67 DN 150 1235 19 0 1136 1 1500 901 C CRI15-9 U2 7.5 91 DN 150 1235 19 0 1214 1 1500 9 C 54
Technical data ydro MPC with CRI(E) 15 / CRI(E) 20 ydro MPC-S with CRI 15 No. of ums Pum tye 2 3 4 5 6 Suly voltage [V] Motor [kw] Max. I N [A] Connection W L1 L2 1 2 Suly voltage U2: 3 x 380-415 V, ± 5 %, PE. Design A: ydro MPC booster system with a control cabinet mounted on the same base frame as the ums. Design B: ydro MPC booster system with a control cabinet centred on the base frame. Design C: ydro MPC booster system with a floor-mounted control cabinet. Design D: ydro MPC booster system with a control cabinet mounted on a searate base frame. All ums are fitted with three-hase motors. Dimensions may vary by ± 10 mm. 3 Weight Design [kg] CRI15-2 U2 2.2 9.5 DN 80 1150 780-764 1 12 190 B CRI15-3 U2 3 12.8 DN 80 1150 780-1068 1 12 201 B CRI15-5 U2 4 16 DN 80 1150 780-995 1 12 229 B CRI15-7 U2 5.5 22 DN 80 1150 1310-1136 1 1455 308 A CRI15-9 U2 7.5 30 DN 80 1150 1310-1214 1 1455 344 A CRI15-2 U2 2.2 14.3 DN 1170 1630-764 1 1455 300 A CRI15-3 U2 3 19.2 DN 1170 1630-1068 1 1455 316 A CRI15-5 U2 4 24 DN 1170 1630-995 1 1455 358 A CRI15-7 U2 5.5 34 DN 1170 1062 7 1136 1 1455 446 D CRI15-9 U2 7.5 46 DN 1170 1062 7 1214 1 1455 500 D CRI15-2 U2 2.2 19 DN 1170 1950-764 1 1455 370 A CRI15-3 U2 3 26 DN 1170 1950-1068 1 1455 391 A CRI15-5 U2 4 32 DN 1170 1950-995 1 1455 447 A CRI15-7 U2 5.5 45 DN 1170 1382 7 1136 1 1455 559 D CRI15-9 U2 7.5 61 DN 1170 1382 7 1214 1 1455 631 D CRI15-2 U2 2.2 24 DN 150 1235 1704 0 764 1 1455 474 D CRI15-3 U2 3 32 DN 150 1235 1704 0 1068 1 1455 501 D CRI15-5 U2 4 DN 150 1235 1704 0 995 1 1455 571 D CRI15-7 U2 5.5 56 DN 150 1235 1704 7 1136 1 1455 716 D CRI15-9 U2 7.5 76 DN 150 1235 1704 7 1214 1 1455 806 D CRI15-2 U2 2.2 29 DN 150 1235 19 0 764 1 1455 551 D CRI15-3 U2 3 38 DN 150 1235 19 0 1068 1 1455 584 D CRI15-5 U2 4 48 DN 150 1235 19 0 995 1 1455 668 D CRI15-7 U2 5.5 67 DN 150 1235 19 800 1136 1 1455 850 D CRI15-9 U2 7.5 91 DN 150 1235 19 800 1214 1 1455 959 D 55
Technical data ydro MPC with CRI(E) 15 / CRI(E) 20 ydro MPC-E with CRIE 20 No. of ums Pum tye 2 3 4 5 6 ydro MPC-F with CRI 20 No. of ums Pum tye 2 3 4 5 6 Suly voltage Motor [V] [kw] Max. I N [A] Connection W L1 L2 1 2 3 Weight Design [kg] CRIE20-2 U2 2.2 9.5 DN 80 1150 1110-804 1 1455 206 A CRIE20-3 U2 4 16 DN 80 1150 1110-905 1 1455 236 A CRIE20-5 U2 5.5 22 DN 80 1150 1110-1046 1 1455 279 A CRIE20-7 U2 7.5 30 DN 80 1150 1110-1124 1 1455 298 A CRIE20-10 U2 11 43 DN 80 1150 920 380 1483 200 1495 439 D CRIE20-2 U2 2.2 14.3 DN 1170 1430-804 1 1455 317 A CRIE20-3 U2 4 24 DN 1170 1430-905 1 1455 363 A CRIE20-5 U2 5.5 33 DN 1170 1430-1046 1 1455 426 A CRIE20-7 U2 7.5 45 DN 1170 1430-1124 1 1455 454 A CRIE20-10 U2 11 64 DN 1170 1522 380 1483 200 1495 650 D CRIE20-2 U2 2.2 19 DN 1170 1750-804 1 1455 397 A CRIE20-3 U2 4 32 DN 1170 1750-905 1 1455 458 A CRIE20-5 U2 5.5 44 DN 1170 1750-1046 1 1455 542 A CRIE20-7 U2 7.5 DN 1170 1750-1124 1 1455 578 A CRIE20-10 U2 11 86 DN 1170 1950 0 1483 200 1495 859 D CRIE20-2 U2 2.2 24 DN 150 1235 1704 380 804 1 1455 509 D CRIE20-3 U2 4 DN 150 1235 1704 380 905 1 1455 586 D CRIE20-5 U2 5.5 55 DN 150 1235 1704 380 1046 1 1455 692 D CRIE20-7 U2 7.5 75 DN 150 1235 1704 0 1124 1 1455 749 D CRIE20-10 U2 11 107 DN 150 1235 2424 0 1443 1 1455 1086 D CRIE20-2 U2 2.2 29 DN 150 1235 19 0 804 1 1455 9 D CRIE20-3 U2 4 48 DN 150 1235 19 0 905 1 1455 701 D CRIE20-5 U2 5.5 66 DN 150 1235 19 0 1046 1 1455 829 D CRIE20-7 U2 7.5 90 DN 150 1235 19 0 1124 1 1455 883 D CRIE20-10 U2 11 128 DN 150 1235 2924 7 1443 1 1455 1313 D Suly voltage [V] Motor [kw] Max. I N [A] Connection W L1 L2 1 2 3 Weight Design [kg] CRI20-2 U2 2.2 9.5 DN 80 1150 7 800 804 1 1500 254 C CRI20-3 U2 4 16 DN 80 1150 7 800 905 1 1500 288 C CRI20-5 U2 5.5 22 DN 80 1150 7 800 1046 1 1500 344 C CRI20-7 U2 7.5 30 DN 80 1150 7 800 1124 1 1500 378 C CRI20-10 U2 11 43 DN 80 1150 920 800 1496 200 1500 447 C CRI20-2 U2 2.2 14.3 DN 1170 1062 800 804 1 1500 346 C CRI20-3 U2 4 24 DN 1170 1062 800 905 1 1500 395 C CRI20-5 U2 5.5 34 DN 1170 1062 800 1046 1 1500 475 C CRI20-7 U2 7.5 46 DN 1170 1062 800 1124 1 1500 527 C CRI20-10 U2 11 64 DN 1170 1522 800 1496 200 1500 625 C CRI20-2 U2 2.2 19 DN 1170 1382 800 804 1 1500 417 C CRI20-3 U2 4 32 DN 1170 1382 800 905 1 1500 483 C CRI20-5 U2 5.5 45 DN 1170 1382 800 1046 1 1500 588 C CRI20-7 U2 7.5 61 DN 1170 1382 800 1124 1 1500 656 C CRI20-10 U2 11 86 DN 1170 1950 800 1496 200 1500 791 C CRI20-2 U2 2.2 24 DN 150 1235 1704 800 804 1 1500 531 C CRI20-3 U2 4 DN 150 1235 1704 800 905 1 1500 614 C CRI20-5 U2 5.5 56 DN 150 1235 1704 800 1046 1 1500 746 C CRI20-7 U2 7.5 76 DN 150 1235 1704 800 1124 1 1500 832 C CRI20-10 U2 11 107 DN 150 1235 2424 0 1456 1 1500 1010 C CRI20-2 U2 2.2 29 DN 150 1235 19 800 804 1 1500 611 C CRI20-3 U2 4 48 DN 150 1235 19 800 905 1 1500 710 C CRI20-5 U2 5.5 67 DN 150 1235 19 0 1046 1 1500 889 C CRI20-7 U2 7.5 91 DN 150 1235 19 0 1124 1 1500 991 C CRI20-10 U2 11 128 DN 150 1235 2924 0 1456 1 1500 1186 C 56
Technical data ydro MPC with CRI(E) 15 / CRI(E) 20 ydro MPC-S with CRI 20 No. of ums Pum tye 2 3 4 5 6 Suly voltage [V] Motor [kw] Max. I N [A] Connection W L1 L2 1 2 Suly voltage U2: 3 x 380-415 V, ± 5 %, PE. Design A: ydro MPC booster system with a control cabinet mounted on the same base frame as the ums. Design B: ydro MPC booster system with a control cabinet centred on the base frame. Design C: ydro MPC booster system with a floor-mounted control cabinet. Design D: ydro MPC booster system with a control cabinet mounted on a searate base frame. All ums are fitted with three-hase motors. Dimensions may vary by ± 10 mm. 3 Weight Design [kg] CRI20-2 U2 2.2 9.5 DN 80 1150 780-804 1 12 190 B CRI20-3 U2 4 16 DN 80 1150 780-905 1 12 223 B CRI20-5 U2 5.5 22 DN 80 1150 1310-1046 1 1455 304 A CRI20-7 U2 7.5 30 DN 80 1150 1310-1124 1 1455 338 A CRI20-10 U2 11 43 DN 80 1150 920 0 1496 200 1495 387 D CRI20-2 U2 2.2 14.3 DN 1170 1630-804 1 1455 300 A CRI20-3 U2 4 24 DN 1170 1630-905 1 1455 349 A CRI20-5 U2 5.5 34 DN 1170 1062 7 1046 1 1455 4 D CRI20-7 U2 7.5 46 DN 1170 1062 7 1124 1 1455 491 D CRI20-10 U2 11 64 DN 1170 1522 7 1496 200 1495 582 D CRI20-2 U2 2.2 19 DN 1170 1950-804 1 1455 370 A CRI20-3 U2 4 32 DN 1170 1950-905 1 1455 435 A CRI20-5 U2 5.5 45 DN 1170 1382 7 1046 1 1455 551 D CRI20-7 U2 7.5 61 DN 1170 1382 7 1124 1 1455 619 D CRI20-10 U2 11 86 DN 1170 1950 7 1496 200 1495 747 D CRI20-2 U2 2.2 24 DN 150 1235 1704 0 804 1 1455 474 D CRI20-3 U2 4 DN 150 1235 1704 0 905 1 1455 556 D CRI20-5 U2 5.5 56 DN 150 1235 1704 7 1046 1 1455 706 D CRI20-7 U2 7.5 76 DN 150 1235 1704 7 1124 1 1455 791 D CRI20-10 U2 11 107 DN 150 1235 2424 7 1456 1 1455 939 D CRI20-2 U2 2.2 29 DN 150 1235 19 0 804 1 1455 551 D CRI20-3 U2 4 48 DN 150 1235 19 0 905 1 1455 650 D CRI20-5 U2 5.5 67 DN 150 1235 19 800 1046 1 1455 838 D CRI20-7 U2 7.5 91 DN 150 1235 19 800 1124 1 1455 9 D CRI20-10 U2 11 128 DN 150 1235 2924 800 1456 1 1500 1146 C 57
Technical data ydro MPC with CR(E) 32 ydro MPC with CR(E) 32 Fig. 47 Dimensional sketch of a ydro MPC booster system with a floor-mounted control cabinet (design C) TM03 1186 2310 TM03 3043 2310 Fig. 48 Dimensional sketch of a ydro MPC booster system with a control cabinet mounted on a searate base frame (design D) 58
Technical data ydro MPC with CR(E) 32 Electrical data, dimensions and weights ydro MPC-E with CRE 32 No. of ums Pum tye 2 3 4 5 6 ydro MPC-F with CR 32 No. of ums Pum tye 2 3 4 5 6 Suly voltage [V] Motor [kw] Max. I N [A] Connection W L1 L2 1 2 3 Weight Design [kg] CRE32-2 U2 4 16 DN 1170 1022 380 1017 175 1455 290 D CRE32-3 U2 5.5 22 DN 1170 1022 380 1106 175 1455 314 D CRE32-4 U2 7.5 30 DN 1170 1022 380 1164 175 1455 367 D CRE32-6 U2 11 43 DN 1170 1022 380 1546 215 1495 281 D CRE32-8 U2 15 56 DN 1170 1022 380 1686 215 1495 473 D CRE32-2 U2 4 24 DN 150 1235 1524 380 1017 175 1455 431 D CRE32-3 U2 5.5 33 DN 150 1235 1524 380 1106 175 1455 464 D CRE32-4 U2 7.5 45 DN 150 1235 1524 380 1164 175 1455 544 D CRE32-6 U2 11 64 DN 150 1235 1524 380 1546 215 1495 417 D CRE32-8 U2 15 84 DN 150 1235 1524 0 1686 215 1495 717 D CRE32-2 U2 4 32 DN 150 1235 2024 380 1017 175 1455 556 D CRE32-3 U2 5.5 44 DN 150 1235 2024 380 1106 175 1455 1 D CRE32-4 U2 7.5 DN 150 1235 2024 380 1164 175 1455 706 D CRE32-6 U2 11 86 DN 150 1235 2024 0 1546 215 1495 549 D CRE32-8 U2 15 112 DN 150 1235 2024 7 1686 215 1495 957 D CRE32-2 U2 4 DN 150 1235 2524 380 1017 175 1455 695 D CRE32-3 U2 5.5 55 DN 150 1235 2524 380 1106 175 1455 752 D CRE32-4 U2 7.5 75 DN 150 1235 2524 0 1164 175 1455 896 D CRE32-6 U2 11 107 DN 150 1235 2524 0 1546 215 1495 685 D CRE32-8 U2 15 1 DN 150 1235 2524 7 1686 215 1495 1189 D CRE32-2 U2 4 48 DN 150 1235 3024 0 1017 175 1455 834 D CRE32-3 U2 5.5 66 DN 150 1235 3024 0 1106 175 1455 902 D CRE32-4 U2 7.5 90 DN 150 1235 3024 0 1164 175 1455 10 D CRE32-6 U2 11 128 DN 150 1235 3024 7 1546 215 1495 831 D CRE32-8 U2 15 168 DN 150 1235 3024 7 1686 215 1495 17 D Suly voltage [V] Motor [kw] Max. I N [A] Connection W L1 L2 1 2 3 Weight Design [kg] CR32-2 U2 4 16 DN 1170 1022 800 1017 175 1500 344 C CR32-3 U2 5.5 22 DN 1170 1022 800 1106 175 1500 387 C CR32-4 U2 7.5 30 DN 1170 1022 800 1164 175 1500 446 C CR32-6 U2 11 43 DN 1170 1022 800 1546 215 1500 491 C CR32-8 U2 15 56 DN 1170 1022 800 1693 215 1500 544 C CR32-2 U2 4 24 DN 150 1235 1524 800 1017 175 1500 479 C CR32-3 U2 5.5 34 DN 150 1235 1524 800 1106 175 1500 5 C CR32-4 U2 7.5 46 DN 150 1235 1524 800 1164 175 1500 630 C CR32-6 U2 11 64 DN 150 1235 1524 800 1546 215 1500 695 C CR32-8 U2 15 84 DN 150 1235 1524 0 1693 215 1500 803 C CR32-2 U2 4 32 DN 150 1235 2024 800 1017 175 1500 1 C CR32-3 U2 5.5 45 DN 150 1235 2024 800 1106 175 1500 681 C CR32-4 U2 7.5 61 DN 150 1235 2024 800 1164 175 1500 799 C CR32-6 U2 11 86 DN 150 1235 2024 800 1546 215 1500 885 C CR32-8 U2 15 112 DN 150 1235 2024 0 1693 215 1500 1019 C CR32-2 U2 4 DN 150 1235 2524 800 1017 175 1500 738 C CR32-3 U2 5.5 56 DN 150 1235 2524 800 1106 175 1500 837 C CR32-4 U2 7.5 76 DN 150 1235 2524 800 1164 175 1500 986 C CR32-6 U2 11 107 DN 150 1235 2524 0 1546 215 1500 1114 C CR32-8 U2 15 1 DN 150 1235 2524 0 1693 215 1500 1249 C CR32-2 U2 4 48 DN 150 1235 3024 800 1017 175 1500 861 C CR32-3 U2 5.5 67 DN 150 1235 3024 0 1106 175 1500 1 C CR32-4 U2 7.5 91 DN 150 1235 3024 0 1164 175 1500 1178 C CR32-6 U2 11 128 DN 150 1235 3024 0 1546 215 1500 1311 C CR32-8 U2 15 168 DN 150 1235 3024 0 1693 215 1500 1468 C 59
Technical data ydro MPC with CR(E) 32 ydro MPC-S with CR 32 No. of ums Pum tye 2 3 4 5 6 Suly voltage [V] Motor [kw] Max. I N [A] Connection W L1 L2 1 Suly voltage U2: 3 x 380-415 V, ± 5 %, PE. Design C: ydro MPC booster system with a floor-mounted control cabinet. Design D: ydro MPC booster system with a control cabinet mounted on a searate base frame. All ums are fitted with three-hase motors. Dimensions may vary by ± 10 mm. 2 3 Weight Design [kg] CR32-2 U2 4 16 DN 1170 1022 380 1017 175 1455 280 D CR32-3 U2 5.5 22 DN 1170 1022 0 1106 175 1455 332 D CR32-4 U2 7.5 30 DN 1170 1022 0 1164 175 1455 391 D CR32-6 U2 11 43 DN 1170 1022 0 1546 215 1495 431 D CR32-8 U2 15 56 DN 1170 1022 0 1693 215 1495 483 D CR32-2 U2 4 24 DN 150 1235 1524 0 1017 175 1455 426 D CR32-3 U2 5.5 34 DN 150 1235 1524 7 1106 175 1455 504 D CR32-4 U2 7.5 46 DN 150 1235 1524 7 1164 175 1455 593 D CR32-6 U2 11 64 DN 150 1235 1524 7 1546 215 1495 652 D CR32-8 U2 15 84 DN 150 1235 1524 7 1693 215 1495 730 D CR32-2 U2 4 32 DN 150 1235 2024 0 1017 175 1455 544 D CR32-3 U2 5.5 45 DN 150 1235 2024 7 1106 175 1455 643 D CR32-4 U2 7.5 61 DN 150 1235 2024 7 1164 175 1455 761 D CR32-6 U2 11 86 DN 150 1235 2024 7 1546 215 1495 841 D CR32-8 U2 15 112 DN 150 1235 2024 800 1693 215 1495 9 D CR32-2 U2 4 DN 150 1235 2524 0 1017 175 1455 679 D CR32-3 U2 5.5 56 DN 150 1235 2524 7 1106 175 1455 796 D CR32-4 U2 7.5 76 DN 150 1235 2524 7 1164 175 1455 944 D CR32-6 U2 11 107 DN 150 1235 2524 7 1546 215 1495 1044 D CR32-8 U2 15 1 DN 150 1235 2524 800 1693 215 1500 1211 C CR32-2 U2 4 48 DN 150 1235 3024 0 1017 175 1455 799 D CR32-3 U2 5.5 67 DN 150 1235 3024 800 1106 175 1455 948 D CR32-4 U2 7.5 91 DN 150 1235 3024 800 1164 175 1455 1125 D CR32-6 U2 11 128 DN 150 1235 3024 800 1546 215 1500 1270 C CR32-8 U2 15 168 DN 150 1235 3024 800 1693 215 1500 1426 C
Technical data ydro MPC with CR(E) 45 / CR(E) 64 ydro MPC with CR(E) 45 / CR(E) 64 Fig. 49 Dimensional sketch of a ydro MPC booster system with a floor-mounted control cabinet (design C) TM03 1187 2310 TM03 1693 2310 Fig. 50 Dimensional sketch of a ydro MPC booster system with a control cabinet mounted on a searate base frame (design D) 61
Technical data ydro MPC with CR(E) 45 / CR(E) 64 Electrical data, dimensions and weights ydro MPC-E with CRE 45 No. of ums Pum tye 3 4 5 6 ydro MPC-F with CR 45 No. of ums Pum tye 3 4 5 6 Suly voltage Motor [V] [kw] Max. I N [A] Connection W L1 L2 1 2 3 Weight Design [kg] CRE45-2-2 U2 5.5 33 DN 200 1390 1526 380 1 210 1455 531 D CRE45-2 U2 7.5 45 DN 200 1390 1526 380 1088 210 1455 558 D CRE45-3 U2 11 64 DN 200 1390 1526 380 1410 250 1495 724 D CRE45-4 U2 15 84 DN 200 1390 1526 0 1490 250 1495 763 D CRE45-5 U2 18.5 102 DN 200 1390 1526 0 1614 250 1495 802 D CRE45-6 U2 22 126 DN 200 1390 1526 7 1720 250 1495 914 D CRE45-2-2 U2 5.5 44 DN 200 1390 2026 380 1 210 1455 688 D CRE45-2 U2 7.5 DN 200 1390 2026 380 1088 210 1455 723 D CRE45-3 U2 11 86 DN 200 1390 2026 0 1410 250 1495 956 D CRE45-4 U2 15 112 DN 200 1390 2026 7 1490 250 1495 1016 D CRE45-5 U2 18.5 136 DN 200 1390 2026 7 1614 250 1495 1069 D CRE45-6 U2 22 168 DN 200 1390 2026 7 1720 250 1495 1185 D CRE45-2-2 U2 5.5 55 DN 200 1390 2526 380 1 210 1455 862 D CRE45-2 U2 7.5 75 DN 200 1390 2526 0 1088 210 1455 918 D CRE45-3 U2 11 107 DN 200 1390 2526 0 1410 250 1495 1195 D CRE45-4 U2 15 1 DN 200 1390 2526 7 1490 250 1495 1264 D CRE45-5 U2 18.5 170 DN 200 1390 2526 7 1614 250 1495 1330 D CRE45-6 U2 22 210 DN 200 1390 2526 800 1720 250 1495 1490 D CRE45-2-2 U2 5.5 66 DN 200 1390 3026 0 1 210 1455 1032 D CRE45-2 U2 7.5 90 DN 200 1390 3026 0 1088 210 1455 1084 D CRE45-3 U2 11 128 DN 200 1390 3026 7 1410 250 1495 1441 D CRE45-4 U2 15 168 DN 200 1390 3026 7 1490 250 1495 1495 D CRE45-5 U2 18.5 204 DN 200 1390 3026 800 1614 250 1495 1589 D CRE45-6 U2 22 252 DN 200 1390 3026 800 1720 250 1495 1768 D Suly voltage [V] Motor [kw] Max. I N [A] Connection W L1 L2 1 2 3 Weight Design [kg] CR45-2-2 U2 5.5 34 DN 200 1390 1526 800 1 210 1500 588 C CR45-2 U2 7.5 46 DN 200 1390 1526 800 1088 210 1500 644 C CR45-3 U2 11 64 DN 200 1390 1526 800 1375 250 1500 750 C CR45-4 U2 15 84 DN 200 1390 1526 0 1490 250 1500 897 C CR45-5 U2 18.5 104 DN 200 1390 1526 0 1614 250 1500 897 C CR45-6 U2 22 125 DN 200 1390 1526 1200 1789 250 1900 1265 C CR45-2-2 U2 5.5 45 DN 200 1390 2026 800 1 210 1500 743 C CR45-2 U2 7.5 61 DN 200 1390 2026 800 1088 210 1500 816 C CR45-3 U2 11 86 DN 200 1390 2026 800 1375 250 1500 956 C CR45-4 U2 15 112 DN 200 1390 2026 0 1490 250 1500 1142 C CR45-5 U2 18.5 138 DN 200 1390 2026 0 1614 250 1500 1142 C CR45-6 U2 22 166 DN 200 1390 2026 1200 1789 250 2000 18 C CR45-2-2 U2 5.5 56 DN 200 1390 2526 800 1 210 1500 916 C CR45-2 U2 7.5 76 DN 200 1390 2526 800 1088 210 1500 8 C CR45-3 U2 11 107 DN 200 1390 2526 0 1375 250 1500 1204 C CR45-4 U2 15 1 DN 200 1390 2526 0 1490 250 1500 14 C CR45-5 U2 18.5 173 DN 200 1390 2526 1200 1614 250 2000 1514 C CR45-6 U2 22 208 DN 200 1390 2526 1200 1789 250 2000 1958 C CR45-2-2 U2 5.5 67 DN 200 1390 3026 0 1 210 1500 1093 C CR45-2 U2 7.5 91 DN 200 1390 3026 0 1088 210 1500 1202 C CR45-3 U2 11 128 DN 200 1390 3026 0 1375 250 1500 1416 C CR45-4 U2 15 168 DN 200 1390 3026 0 1490 250 1500 1651 C CR45-5 U2 18.5 207 DN 200 1390 3026 1200 1614 250 2000 1761 C CR45-6 U2 22 249 DN 200 1390 3026 1200 1789 250 2000 2297 C 62
Technical data ydro MPC with CR(E) 45 / CR(E) 64 ydro MPC-S with CR 45 No. of ums Pum tye 3 4 5 6 Suly voltage [V] Motor [kw] Max. I N [A] Connection W L1 L2 1 Suly voltage U2: 3 x 380-415 V, ± 5 %, PE. Design C: ydro MPC booster system with a floor-mounted control cabinet. Design D: ydro MPC booster system with a control cabinet mounted on a searate base frame. All ums are fitted with three-hase motors. Dimensions may vary by ± 10 mm. 2 3 Weight Design [kg] CR45-2-2 U2 5.5 34 DN 200 1390 1526 7 1 210 1455 552 D CR45-2 U2 7.5 46 DN 200 1390 1526 7 1088 210 1455 7 D CR45-3 U2 11 64 DN 200 1390 1526 7 1375 250 1495 707 D CR45-4 U2 15 84 DN 200 1390 1526 7 1490 250 1495 824 D CR45-5 U2 18.5 104 DN 200 1390 1526 7 1614 250 1495 823 D CR45-6 U2 22 125 DN 200 1390 1526 800 1789 250 1495 1087 D CR45-2-2 U2 5.5 45 DN 200 1390 2026 7 1 210 1455 705 D CR45-2 U2 7.5 61 DN 200 1390 2026 7 1088 210 1455 778 D CR45-3 U2 11 86 DN 200 1390 2026 7 1375 250 1495 912 D CR45-4 U2 15 112 DN 200 1390 2026 800 1490 250 1495 1083 D CR45-5 U2 18.5 138 DN 200 1390 2026 800 1614 250 1500 1104 C CR45-6 U2 22 166 DN 200 1390 2026 800 1789 250 1500 1433 C CR45-2-2 U2 5.5 56 DN 200 1390 2526 7 1 210 1455 875 D CR45-2 U2 7.5 76 DN 200 1390 2526 7 1088 210 1455 966 D CR45-3 U2 11 107 DN 200 1390 2526 7 1375 250 1495 1134 D CR45-4 U2 15 1 DN 200 1390 2526 800 1490 250 1500 1365 C CR45-5 U2 18.5 173 DN 200 1390 2526 800 1614 250 1500 1364 C CR45-6 U2 22 208 DN 200 1390 2526 0 1789 250 2000 1855 C CR45-2-2 U2 5.5 67 DN 200 1390 3026 800 1 210 1455 10 D CR45-2 U2 7.5 91 DN 200 1390 3026 800 1088 210 1455 1149 D CR45-3 U2 11 128 DN 200 1390 3026 800 1375 250 1500 1376 C CR45-4 U2 15 168 DN 200 1390 3026 800 1490 250 1500 19 C CR45-5 U2 18.5 207 DN 200 1390 3026 0 1614 250 2000 1688 C CR45-6 U2 22 249 DN 200 1390 3026 0 1789 250 2000 2183 C 63
Technical data ydro MPC with CR(E) 45 / CR(E) 64 ydro MPC-E with CRE 64 No. of ums Pum tye 3 4 5 6 Suly voltage Motor [V] [kw] Max. I N [A] Connection CR64-5-1 U2 30 336 DN 200 1390 3026 20 1762 250 2000 3084 C Suly voltage U2: 3 x 380-415 V, ± 5 %, PE. Design D: ydro MPC booster system with a control cabinet mounted on a searate base frame. All ums are fitted with three-hase motors. Dimensions may vary by ± 10 mm. W L1 L2 1 2 3 Weight Design [kg] CRE64-1 U2 5.5 33 DN 200 1390 1526 380 1022 210 1455 541 D CRE64-2-2 U2 7.5 45 DN 200 1390 1526 380 1093 210 1455 551 D CRE64-2 U2 11 64 DN 200 1390 1526 380 1335 250 1495 715 D CRE64-3-1 U2 15 84 DN 200 1390 1526 0 1417 250 1495 750 D CRE64-4-2 U2 18.5 102 DN 200 1390 1526 0 1544 250 1495 863 D CRE64-4 U2 22 126 DN 200 1390 1526 7 1570 250 1495 902 D CR64-5-1 U2 30 168 DN 200 1390 1526 0 1762 250 2000 1512 C CRE64-1 U2 5.5 44 DN 200 1390 2026 380 1022 210 1455 702 D CRE64-2-2 U2 7.5 DN 200 1390 2026 380 1093 210 1455 714 D CRE64-2 U2 11 86 DN 200 1390 2026 0 1335 250 1495 945 D CRE64-3-1 U2 15 112 DN 200 1390 2026 7 1417 250 1495 0 D CRE64-4-2 U2 18.5 136 DN 200 1390 2026 7 1544 250 1495 1150 D CRE64-4 U2 22 168 DN 200 1390 2026 7 1570 250 1495 1171 D CR64-5-1 U2 30 224 DN 200 1390 2026 20 1762 250 2000 2172 C CRE64-1 U2 5.5 55 DN 200 1390 2526 380 1022 210 1455 879 D CRE64-2-2 U2 7.5 75 DN 200 1390 2526 0 1093 210 1455 907 D CRE64-2 U2 11 107 DN 200 1390 2526 0 1335 250 1495 1181 D CRE64-3-1 U2 15 1 DN 200 1390 2526 7 1417 250 1495 1243 D CRE64-4-2 U2 18.5 170 DN 200 1390 2526 7 1544 250 1495 1431 D CRE64-4 U2 22 210 DN 200 1390 2526 800 1570 250 1495 1471 D CR64-5-1 U2 30 280 DN 200 1390 2526 20 1762 250 2000 2639 C CRE64-1 U2 5.5 66 DN 200 1390 3026 0 1022 210 1455 1052 D CRE64-2-2 U2 7.5 90 DN 200 1390 3026 0 1093 210 1455 1070 D CRE64-2 U2 11 128 DN 200 1390 3026 7 1335 250 1495 1424 D CRE64-3-1 U2 15 168 DN 200 1390 3026 7 1417 250 1495 1469 D CRE64-4-2 U2 18.5 204 DN 200 1390 3026 800 1544 250 1495 1710 D CRE64-4 U2 22 252 DN 200 1390 3026 800 1570 250 1495 1745 D 64
Technical data ydro MPC with CR(E) 45 / CR(E) 64 ydro MPC-F with CR 64 No. of ums Pum tye 3 4 5 6 Suly voltage [V] Motor [kw] Max. I N [A] Connection CR64-5-1 U2 30 336 DN 200 1390 3026 30 1762 250 2000 3161 C Suly voltage U2: 3 x 380-415 V, ± 5 %, PE. Design C: ydro MPC booster system with a floor-mounted control cabinet. All ums are fitted with three-hase motors. Dimensions may vary by ± 10 mm. W L1 L2 1 2 3 Weight Design [kg] CR64-1 U2 5.5 34 DN 200 1390 1526 800 1022 210 1500 620 C CR64-2-2 U2 7.5 46 DN 200 1390 1526 800 1093 210 1500 684 C CR64-2 U2 11 64 DN 200 1390 1526 800 1335 250 1500 785 C CR64-3-1 U2 15 84 DN 200 1390 1526 0 1417 250 1500 986 C CR64-4-2 U2 18.5 104 DN 200 1390 1526 0 1504 250 1500 1017 C CR64-4 U2 22 125 DN 200 1390 1526 1200 1570 250 1900 1241 C CR64-5-1 U2 30 168 DN 200 1390 1526 1200 1762 250 2000 1522 C CR64-1 U2 5.5 45 DN 200 1390 2026 800 1022 210 1500 786 C CR64-2-2 U2 7.5 61 DN 200 1390 2026 800 1093 210 1500 870 C CR64-2 U2 11 86 DN 200 1390 2026 800 1335 250 1500 4 C CR64-3-1 U2 15 112 DN 200 1390 2026 0 1417 250 1500 1262 C CR64-4-2 U2 18.5 138 DN 200 1390 2026 0 1504 250 1500 1302 C CR64-4 U2 22 166 DN 200 1390 2026 1200 1570 250 2000 1576 C CR64-5-1 U2 30 224 DN 200 1390 2026 1200 1762 250 2000 1937 C CR64-1 U2 5.5 56 DN 200 1390 2526 800 1022 210 1500 969 C CR64-2-2 U2 7.5 76 DN 200 1390 2526 800 1093 210 1500 1076 C CR64-2 U2 11 107 DN 200 1390 2526 0 1335 250 1500 1263 C CR64-3-1 U2 15 1 DN 200 1390 2526 0 1417 250 1500 1553 C CR64-4-2 U2 18.5 173 DN 200 1390 2526 1200 1504 250 2000 1714 C CR64-4 U2 22 208 DN 200 1390 2526 1200 1570 250 2000 1918 C CR64-5-1 U2 30 280 DN 200 1390 2526 30 1762 250 2000 2734 C CR64-1 U2 5.5 67 DN 200 1390 3026 0 1022 210 1500 1157 C CR64-2-2 U2 7.5 91 DN 200 1390 3026 0 1093 210 1500 1283 C CR64-2 U2 11 128 DN 200 1390 3026 0 1335 250 1500 1487 C CR64-3-1 U2 15 168 DN 200 1390 3026 0 1417 250 1500 1829 C CR64-4-2 U2 18.5 207 DN 200 1390 3026 1200 1504 250 2000 2001 C CR64-4 U2 22 249 DN 200 1390 3026 1200 1570 250 2000 2249 C 65
Technical data ydro MPC with CR(E) 45 / CR(E) 64 ydro MPC-S with CR 64 No. of ums Pum tye 3 4 5 6 Suly voltage [V] Motor [kw] Max. I N [A] Connection W L1 L2 1 Suly voltage U2: 3 x 380-415 V, ± 5 %, PE. Design C: ydro MPC booster system with a floor-mounted control cabinet. Design D: ydro MPC booster system with a control cabinet mounted on a searate base frame. All ums are fitted with three-hase motors. Dimensions may vary by ± 10 mm. 2 3 Weight Design [kg] CR64-1 U2 5.5 34 DN 200 1390 1526 7 1022 210 1455 584 D CR64-2-2 U2 7.5 46 DN 200 1390 1526 7 1093 210 1455 647 D CR64-2 U2 11 64 DN 200 1390 1526 7 1335 250 1495 742 D CR64-3-1 U2 15 84 DN 200 1390 1526 7 1417 250 1495 913 D CR64-4-2 U2 18.5 104 DN 200 1390 1526 7 1504 250 1495 943 D CR64-4 U2 22 125 DN 200 1390 1526 800 1570 250 1495 1063 D CR64-5-1 U2 30 168 DN 200 1390 1526 800 1762 250 1495 1327 D CR64-1 U2 5.5 45 DN 200 1390 2026 7 1022 210 1455 748 D CR64-2-2 U2 7.5 61 DN 200 1390 2026 7 1093 210 1455 832 D CR64-2 U2 11 86 DN 200 1390 2026 7 1335 250 1495 9 D CR64-3-1 U2 15 112 DN 200 1390 2026 800 1417 250 1495 1202 D CR64-4-2 U2 18.5 138 DN 200 1390 2026 800 1504 250 1500 1264 C CR64-4 U2 22 166 DN 200 1390 2026 800 1570 250 1500 12 C CR64-5-1 U2 30 224 DN 200 1390 2026 800 1762 250 2000 1807 C CR64-1 U2 5.5 56 DN 200 1390 2526 7 1022 210 1455 928 D CR64-2-2 U2 7.5 76 DN 200 1390 2526 7 1093 210 1455 1033 D CR64-2 U2 11 107 DN 200 1390 2526 7 1335 250 1495 1193 D CR64-3-1 U2 15 1 DN 200 1390 2526 800 1417 250 1500 1514 C CR64-4-2 U2 18.5 173 DN 200 1390 2526 800 1504 250 1500 1564 C CR64-4 U2 22 208 DN 200 1390 2526 0 1570 250 2000 1816 C CR64-5-1 U2 30 280 DN 200 1390 2526 1200 1762 250 2000 2308 C CR64-1 U2 5.5 67 DN 200 1390 3026 800 1022 210 1455 1104 D CR64-2-2 U2 7.5 91 DN 200 1390 3026 800 1093 210 1455 1230 D CR64-2 U2 11 128 DN 200 1390 3026 800 1335 250 1500 1446 C CR64-3-1 U2 15 168 DN 200 1390 3026 800 1417 250 1500 1787 C CR64-4-2 U2 18.5 207 DN 200 1390 3026 0 1504 250 2000 1928 C CR64-4 U2 22 249 DN 200 1390 3026 0 1570 250 2000 2135 C CR64-5-1 U2 30 336 DN 200 1390 3026 10 1762 250 2000 2754 C 66
Technical data ydro MPC with CR(E) 90 ydro MPC with CR(E) 90 Fig. 51 Dimensional sketch of a ydro MPC booster system with a floor-mounted control cabinet (design C) TM03 1190 2310 TM03 3046 2310 Fig. 52 Dimensional sketch of a ydro MPC booster system with a control cabinet mounted on a searate base frame (design D) 67
Technical data ydro MPC with CR(E) 90 Electrical data, dimensions and weights ydro MPC-E with CRE 90 No. of ums Pum tye Suly voltage Motor [V] [kw] Max. I N [A] Connection CRE90-2-2 U2 11 64 DN 200 15 1526 380 1354 250 1495 733 D CRE90-2 U2 15 84 DN 200 15 1526 0 1354 250 1495 754 D CRE90-3-2 U2 18.5 102 DN 200 15 1526 0 1490 250 1495 982 D 3 CRE90-3 U2 22 126 DN 200 15 1526 7 1516 250 1495 957 D CR90-4-2 U2 30 168 DN 200 15 1526 0 1713 250 2000 1439 C CR90-4 U2 30 168 DN 200 15 1526 0 1718 250 2000 1521 C CR90-5-2 U2 37 216 DN 200 15 1526 20 1862 250 2000 1797 C CRE90-2-2 U2 11 86 DN 250 15 2026 0 1354 250 1495 984 D CRE90-2 U2 15 112 DN 250 15 2026 7 1354 250 1495 1020 D CRE90-3-2 U2 18.5 136 DN 250 15 2026 7 1490 250 1495 1324 D 4 CRE90-3 U2 22 168 DN 250 15 2026 7 1516 250 1495 1257 D CR90-4-2 U2 30 224 DN 250 15 2026 20 1713 250 2000 2088 C CR90-4 U2 30 224 DN 250 15 2026 20 1718 250 2000 2198 C CR90-5-2 U2 37 288 DN 250 15 2026 20 1862 250 2000 2262 C CRE90-2-2 U2 11 107 DN 250 15 2526 0 1354 250 1495 1367 D CRE90-2 U2 15 1 DN 250 15 2526 7 1354 250 1495 16 D CRE90-3-2 U2 18.5 170 DN 250 15 2526 7 1490 250 1495 1786 D 5 CRE90-3 U2 22 210 DN 250 15 2526 800 1516 250 1495 1718 D CR90-4-2 U2 30 280 DN 250 15 2526 20 1713 250 2000 2672 C CR90-4 U2 30 280 DN 250 15 2526 20 1718 250 2000 2809 C CR90-5-2 U2 37 3 DN 250 15 2526 30 1862 250 2000 3087 C CRE90-2-2 U2 11 128 DN 250 15 3026 7 1354 250 1495 1619 D CRE90-2 U2 15 168 DN 250 15 3026 7 1354 250 1495 1637 D CRE90-3-2 U2 18.5 204 DN 250 15 3026 800 1490 250 1495 2107 D 6 CRE90-3 U2 22 252 DN 250 15 3026 800 1516 250 1495 2013 D CR90-4-2 U2 30 336 DN 250 15 3026 20 1713 250 2000 3096 C CR90-4 U2 30 336 DN 250 15 3026 20 1718 250 2000 3261 C CR90-5-2 U2 37 432 DN 250 15 3026 4800 1862 250 2000 3747 C Suly voltage U2: 3 x 380-415 V, ± 5 %, PE. Design C: ydro MPC booster system with a floor-mounted control cabinet. Design D: ydro MPC booster system with a control cabinet mounted on a searate base frame. All ums are fitted with three-hase motors. Dimensions may vary by ± 10 mm. W L1 L2 1 2 3 Weight Design [kg] 68
Technical data ydro MPC with CR(E) 90 ydro MPC-F with CR 90 No. of ums Pum tye 3 4 5 6 Suly voltage [V] Motor [kw] Max. I N [A] Connection CR90-5-2 U2 37 432 DN 250 15 3026 30 1862 250 2000 3435 C Suly voltage U2: 3 x 380-415 V, ± 5 %, PE. Design C: ydro MPC booster system with a floor-mounted control cabinet. All ums are fitted with three-hase motors. Dimensions may vary by ± 10 mm. W L1 L2 1 2 3 Weight Design [kg] CR90-2-2 U2 11 64 DN 200 15 1526 800 1354 250 1500 806 C CR90-2 U2 15 84 DN 200 15 1526 0 1361 250 1500 8 C CR90-3-2 U2 18.5 104 DN 200 15 1526 0 1490 250 1500 1012 C CR90-3 U2 22 125 DN 200 15 1526 1200 1466 250 1900 1194 C CR90-4-2 U2 30 168 DN 200 15 1526 1200 1713 250 2000 1449 C CR90-4 U2 30 168 DN 200 15 1526 1200 1718 250 2000 1531 C CR90-5-2 U2 37 216 DN 200 15 1526 20 1862 250 2000 1751 C CR90-2-2 U2 11 86 DN 250 15 2026 800 1354 250 1500 1046 C CR90-2 U2 15 112 DN 250 15 2026 0 1361 250 1500 1081 C CR90-3-2 U2 18.5 138 DN 250 15 2026 0 1490 250 1500 1310 C CR90-3 U2 22 166 DN 250 15 2026 1200 1466 250 2000 1528 C CR90-4-2 U2 30 224 DN 250 15 2026 1200 1713 250 2000 1853 C CR90-4 U2 30 224 DN 250 15 2026 1200 1718 250 2000 1963 C CR90-5-2 U2 37 288 DN 250 15 2026 30 1862 250 2000 2397 C CR90-2-2 U2 11 107 DN 250 15 2526 0 1354 250 1500 1454 C CR90-2 U2 15 1 DN 250 15 2526 0 1361 250 1500 1466 C CR90-3-2 U2 18.5 173 DN 250 15 2526 1200 1490 250 2000 1862 C CR90-3 U2 22 208 DN 250 15 2526 1200 1466 250 2000 1996 C CR90-4-2 U2 30 280 DN 250 15 2526 30 1713 250 2000 2767 C CR90-4 U2 30 280 DN 250 15 2526 30 1718 250 2000 2905 C CR90-5-2 U2 37 3 DN 250 15 2526 30 1862 250 2000 2995 C CR90-2-2 U2 11 128 DN 250 15 3026 0 1354 250 1500 1688 C CR90-2 U2 15 168 DN 250 15 3026 0 1361 250 1500 1697 C CR90-3-2 U2 18.5 207 DN 250 15 3026 1200 1490 250 2000 2150 C CR90-3 U2 22 249 DN 250 15 3026 1200 1466 250 2000 2314 C CR90-4-2 U2 30 336 DN 250 15 3026 30 1713 250 2000 3173 C CR90-4 U2 30 336 DN 250 15 3026 30 1718 250 2000 3338 C 69
Technical data ydro MPC with CR(E) 90 ydro MPC-S with CR 90 No. of ums Pum tye 3 4 5 6 Suly voltage [V] Motor [kw] Max. I N [A] Connection W L1 L2 1 Suly voltage U2: 3 x 380-415 V, ± 5 %, PE. Design C: ydro MPC booster system with a floor-mounted control cabinet. Design D: ydro MPC booster system with a control cabinet mounted on a searate base frame. All ums are fitted with three-hase motors. Dimensions may vary by ± 10 mm. 2 3 Weight Design [kg] CR90-2-2 U2 11 64 DN 200 15 1526 7 1354 250 1495 763 D CR90-2 U2 15 84 DN 200 15 1526 7 1361 250 1495 768 D CR90-3-2 U2 18.5 104 DN 200 15 1526 7 1490 250 1495 938 D CR90-3 U2 22 125 DN 200 15 1526 800 1466 250 1495 1016 D CR90-4-2 U2 30 168 DN 200 15 1526 800 1713 250 1495 1254 D CR90-4 U2 30 168 DN 200 15 1526 800 1718 250 1495 1336 D CR90-5-2 U2 37 216 DN 200 15 1526 0 1862 250 2000 1484 C CR90-2-2 U2 11 86 DN 250 15 2026 7 1354 250 1495 2 D CR90-2 U2 15 112 DN 250 15 2026 800 1361 250 1495 1022 D CR90-3-2 U2 18.5 138 DN 250 15 2026 800 1490 250 1500 1272 C CR90-3 U2 22 166 DN 250 15 2026 800 1466 250 1500 1353 C CR90-4-2 U2 30 224 DN 250 15 2026 800 1713 250 2000 1723 C CR90-4 U2 30 224 DN 250 15 2026 800 1718 250 2000 1833 C CR90-5-2 U2 37 288 DN 250 15 2026 10 1862 250 2000 2008 C CR90-2-2 U2 11 107 DN 250 15 2526 7 1354 250 1495 1384 D CR90-2 U2 15 1 DN 250 15 2526 800 1361 250 1500 1428 C CR90-3-2 U2 18.5 173 DN 250 15 2526 800 1490 250 1500 1712 C CR90-3 U2 22 208 DN 250 15 2526 0 1466 250 2000 1893 C CR90-4-2 U2 30 280 DN 250 15 2526 1200 1713 250 2000 2341 C CR90-4 U2 30 280 DN 250 15 2526 1200 1718 250 2000 2479 C CR90-5-2 U2 37 3 DN 250 15 2526 10 1862 250 2000 21 C CR90-2-2 U2 11 128 DN 250 15 3026 800 1354 250 1500 1647 C CR90-2 U2 15 168 DN 250 15 3026 800 1361 250 1500 1655 C CR90-3-2 U2 18.5 207 DN 250 15 3026 0 1490 250 2000 2077 C CR90-3 U2 22 249 DN 250 15 3026 0 1466 250 2000 2200 C CR90-4-2 U2 30 336 DN 250 15 3026 10 1713 250 2000 2766 C CR90-4 U2 30 336 DN 250 15 3026 10 1718 250 2000 2931 C CR90-5-2 U2 37 432 DN 250 15 3026 10 1862 250 2000 3041 C 70
Technical data ydro MPC with CR(E) 120 / CR(E) 150 ydro MPC with CR(E) 120 / CR(E) 150 Fig. 53 Dimensional sketch of a ydro MPC booster system with a control cabinet mounted on a searate base frame (design C) TM04 44 2410 TM04 4826 2410 Fig. 54 Dimensional sketch of a ydro MPC booster system with a control cabinet mounted on a searate base frame (design D) 71
Technical data ydro MPC with CR(E) 120 / CR(E) 150 Electrical data, dimensions and weights ydro MPC-E with CR(E) 120 No. of ums Pum tye 3 4 5 6 ydro MPC-F with CR 120 No. of ums Pum tye 3 4 5 6 Suly voltage [V] Motor [kw] Max. I N [A] Connection CR120-5-1 U2 45 528 DN 300 2632 3928 30 2335 345 2000 5498 C Suly voltage U2: 3 x 380-415 V, ± 5 %, PE. Design C: ydro MPC booster system with a floor-mounted control cabinet. All ums are fitted with three-hase motors. Dimensions may vary by ± 10 mm. W L1 L2 1 2 3 Weight Design [kg] CRE120-2-1 U2 22 126 DN 300 2632 1978 7 1675 345 1555 1843 D CRE120-2 U2 22 126 DN 300 2632 1978 7 1701 345 1555 19 D CR120-3 U2 37 216 DN 300 2632 1978 20 1961 345 2000 2506 C CR120-4-1 U2 37 216 DN 300 2632 1978 20 2174 345 2000 2626 C CR120-5-1 U2 45 264 DN 300 2632 1978 20 2335 345 2000 2955 C CRE120-2-1 U2 22 168 DN 300 2632 2628 7 1675 345 1555 2486 D CRE120-2 U2 22 168 DN 300 2632 2628 7 1701 345 1555 2642 D CR120-3 U2 37 288 DN 300 2632 2628 20 1961 345 2000 3255 C CR120-4-1 U2 37 288 DN 300 2632 2628 20 2174 345 2000 3415 C CR120-5-1 U2 45 352 DN 300 2632 2628 30 2335 345 2000 57 C CRE120-2-1 U2 22 210 DN 300 2632 3278 800 1675 345 1555 3026 D CRE120-2 U2 22 210 DN 300 2632 3278 800 1701 345 1555 3220 D CR120-3 U2 37 3 DN 300 2632 3278 30 1961 345 2000 4102 C CR120-4-1 U2 37 3 DN 300 2632 3278 30 2174 345 2000 4302 C CR120-5-1 U2 45 4 DN 300 2632 3278 30 2335 345 2000 4851 C CRE120-2-1 U2 22 252 DN 300 2632 3928 800 1675 345 1555 3555 D CRE120-2 U2 22 252 DN 300 2632 3928 800 1701 345 1555 3789 D CR120-3 U2 37 432 DN 300 2632 3928 4800 1961 345 2000 49 C CR120-4-1 U2 37 432 DN 300 2632 3928 4800 2174 345 2000 5180 C CR120-5-1 U2 45 528 DN 300 2632 3928 4800 2335 345 2000 5844 C Suly voltage Motor [V] [kw] Max. I N [A] Connection W L1 L2 1 2 3 Weight Design [kg] CR120-2-1 U2 18.5 104 DN 300 2632 1978 0 1678 345 1500 1678 C CR120-2 U2 22 125 DN 300 2632 1978 1200 1770 345 1900 2061 C CR120-3 U2 37 216 DN 300 2632 1978 20 1961 345 2000 2459 C CR120-4-1 U2 37 216 DN 300 2632 1978 20 2174 345 2000 2578 C CR120-5-1 U2 45 264 DN 300 2632 1978 20 2335 345 2000 2897 C CR120-2-1 U2 18.5 138 DN 300 2632 2628 0 1678 345 1500 2245 C CR120-2 U2 22 166 DN 300 2632 2628 1200 1770 345 2000 2730 C CR120-3 U2 37 288 DN 300 2632 2628 30 1961 345 2000 3388 C CR120-4-1 U2 37 288 DN 300 2632 2628 30 2174 345 2000 3548 C CR120-5-1 U2 45 352 DN 300 2632 2628 30 2335 345 2000 3965 C CR120-2-1 U2 18.5 173 DN 300 2632 3278 1200 1678 345 2000 2803 C CR120-2 U2 22 208 DN 300 2632 3278 1200 1770 345 2000 3271 C CR120-3 U2 37 3 DN 300 2632 3278 30 1961 345 2000 07 C CR120-4-1 U2 37 3 DN 300 2632 3278 30 2174 345 2000 4207 C CR120-5-1 U2 45 4 DN 300 2632 3278 30 2335 345 2000 4725 C CR120-2-1 U2 18.5 207 DN 300 2632 3928 1200 1678 345 2000 3253 C CR120-2 U2 22 249 DN 300 2632 3928 1200 1770 345 2000 3818 C CR120-3 U2 37 432 DN 300 2632 3928 30 1961 345 2000 4625 C CR120-4-1 U2 37 432 DN 300 2632 3928 30 2174 345 2000 4865 C 72
Technical data ydro MPC with CR(E) 120 / CR(E) 150 ydro MPC-S with CR 120 No. of ums Pum tye 3 4 5 6 Suly voltage Motor [V] [kw] Max. I N [A] Connection W L1 L2 1 2 3 Weight Design [kg] CR120-2-1 U2 18.5 104 DN 300 2632 1978 7 1678 345 1555 14 D CR120-2 U2 22 125 DN 300 2632 1978 800 1770 345 1555 1881 D CR120-3 U2 37 216 DN 300 2632 1978 0 1961 345 2000 2191 C CR120-4-1 U2 37 216 DN 300 2632 1978 0 2174 345 2000 2310 C CR120-5-1 U2 45 264 DN 300 2632 1978 1200 2335 345 2000 2650 C CR120-2-1 U2 18.5 138 DN 300 2632 2628 800 1678 345 1500 2207 C CR120-2 U2 22 166 DN 300 2632 2628 800 1770 345 1500 2555 C CR120-3 U2 37 288 DN 300 2632 2628 10 1961 345 2000 2998 C CR120-4-1 U2 37 288 DN 300 2632 2628 10 2174 345 2000 3157 C CR120-5-1 U2 45 352 DN 300 2632 2628 10 2335 345 2000 3556 C CR120-2-1 U2 18.5 173 DN 300 2632 3278 800 1678 345 1500 2653 C CR120-2 U2 22 208 DN 300 2632 3278 0 1770 345 2000 3167 C CR120-3 U2 37 3 DN 300 2632 3278 10 1961 345 2000 3611 C CR120-4-1 U2 37 3 DN 300 2632 3278 10 2174 345 2000 3811 C CR120-5-1 U2 45 4 DN 300 2632 3278 10 2335 345 2000 4307 C CR120-2-1 U2 18.5 207 DN 300 2632 3928 0 1678 345 2000 3179 C CR120-2 U2 22 249 DN 300 2632 3928 0 1770 345 2000 3703 C CR120-3 U2 37 432 DN 300 2632 3928 10 1961 345 2000 4228 C CR120-4-1 U2 37 432 DN 300 2632 3928 10 2174 345 2000 4467 C CR120-5-1 U2 45 528 DN 300 2632 3928 10 2335 345 2000 5073 C ydro MPC-E with CR(E) 150 No. of ums Pum tye 3 4 5 6 Suly voltage [V] Motor [kw] Max. I N [A] Connection CR150-4-1 U2 45 528 DN350 2850 3930 4800 2180 345 2000 6152 C Suly voltage U2: 3 x 380-415 V, ± 5 %, PE. Design C: ydro MPC booster system with a floor-mounted control cabinet. Design D: ydro MPC booster system with a control cabinet mounted on a searate base frame. All ums are fitted with three-hase motors. Dimensions may vary by ± 10 mm. W L1 L2 1 2 3 Weight Design [kg] CRE150-2-1 U2 22 126 DN350 2850 1980 7 1701 345 1555 21 D CR150-3-2 U2 30 168 DN350 2850 1980 0 1961 345 2000 2456 C CR150-3 U2 37 216 DN350 2850 1980 20 2018 345 2000 2797 C CR150-4-1 U2 45 264 DN350 2850 1980 20 2180 345 2000 3125 C CR150-5-2 U2 55 315 DN350 2850 1980 20 23 345 2000 3572 C CRE150-2-1 U2 22 168 DN350 2850 2630 7 1701 345 1555 2923 D CR150-3-2 U2 30 224 DN350 2850 2630 20 1961 345 2000 3507 C CR150-3 U2 37 288 DN350 2850 2630 20 2018 345 2000 3657 C CR150-4-1 U2 45 352 DN350 2850 2630 30 2180 345 2000 4298 C CR150-5-2 U2 55 420 DN350 2850 2630 30 23 345 2000 4887 C CRE150-2-1 U2 22 210 DN350 2850 3280 800 1701 345 1555 3544 D CR150-3-2 U2 30 280 DN350 2850 3280 20 1961 345 2000 4191 C CR150-3 U2 37 3 DN350 2850 3280 30 2018 345 2000 4578 C CR150-4-1 U2 45 4 DN350 2850 3280 30 2180 345 2000 5126 C CR150-5-2 U2 55 525 DN350 2850 3280 30 23 345 2000 5863 C CRE150-2-1 U2 22 252 DN350 2850 3930 800 1701 345 1555 4156 D CR150-3-2 U2 30 336 DN350 2850 3930 20 1961 345 2000 4872 C CR150-3 U2 37 432 DN350 2850 3930 4800 2018 345 2000 5489 C 73
Technical data ydro MPC with CR(E) 120 / CR(E) 150 ydro MPC-F with CR 150 No. of ums Pum tye 3 4 5 6 ydro MPC-S with CR 150 No. of ums Pum tye 3 4 5 6 Suly voltage Motor [V] [kw] Max. I N [A] Connection W L1 L2 1 Suly voltage U2: 3 x 380-415 V, ± 5 %, PE. Design C: ydro MPC booster system with a floor-mounted control cabinet. Design D: ydro MPC booster system with a control cabinet mounted on a searate base frame. All ums are fitted with three-hase motors. Dimensions may vary by ± 10 mm. 2 3 Weight Design [kg] CR150-2-1 U2 22 125 DN350 2850 1980 1200 1770 345 1900 2261 C CR150-3-2 U2 30 168 DN350 2850 1980 1200 1961 345 2000 2465 C CR150-3 U2 37 216 DN350 2850 1980 20 2018 345 2000 2750 C CR150-4-1 U2 45 264 DN350 2850 1980 20 2180 345 2000 3068 C CR150-5-2 U2 55 315 DN350 2850 1980 20 23 345 2000 3513 C CR150-2-1 U2 22 166 DN350 2850 2630 1200 1770 345 2000 3011 C CR150-3-2 U2 30 224 DN350 2850 2630 1200 1961 345 2000 3270 C CR150-3 U2 37 288 DN350 2850 2630 30 2018 345 2000 3790 C CR150-4-1 U2 45 352 DN350 2850 2630 30 2180 345 2000 4206 C CR150-5-2 U2 55 420 DN350 2850 2630 30 23 345 2000 4792 C CR150-2-1 U2 22 208 DN350 2850 3280 1200 1770 345 2000 3595 C CR150-3-2 U2 30 280 DN350 2850 3280 30 1961 345 2000 4283 C CR150-3 U2 37 3 DN350 2850 3280 30 2018 345 2000 4482 C CR150-4-1 U2 45 4 DN350 2850 3280 30 2180 345 2000 5000 C CR150-5-2 U2 55 525 DN350 2850 3280 30 23 345 2000 5742 C CR150-2-1 U2 22 249 DN350 2850 3930 1200 1770 345 2000 4185 C CR150-3-2 U2 30 336 DN350 2850 3930 30 1961 345 2000 4945 C CR150-3 U2 37 432 DN350 2850 3930 30 2018 345 2000 5174 C CR150-4-1 U2 45 528 DN350 2850 3930 30 2180 345 2000 5805 C CR150-5-2 U2 55 630 DN350 2850 3930 30 23 345 2000 6693 C Suly voltage Motor [V] [kw] Max. I N [A] Connection W L1 L2 1 2 3 Weight Design [kg] CR150-2-1 U2 22 125 DN350 2850 1980 800 1770 345 1555 2081 D CR150-3-2 U2 30 168 DN350 2850 1980 800 1961 345 1555 2268 D CR150-3 U2 37 216 DN350 2850 1980 0 2018 345 2000 2482 C CR150-4-1 U2 45 264 DN350 2850 1980 1200 2180 345 2000 2821 C CR150-5-2 U2 55 315 DN350 2850 1980 1200 23 345 2000 3263 C CR150-2-1 U2 22 166 DN350 2850 2630 800 1770 345 1500 2836 C CR150-3-2 U2 30 224 DN350 2850 2630 800 1961 345 2000 3138 C CR150-3 U2 37 288 DN350 2850 2630 10 2018 345 2000 30 C CR150-4-1 U2 45 352 DN350 2850 2630 10 2180 345 2000 3797 C CR150-5-2 U2 55 420 DN350 2850 2630 10 23 345 2000 4381 C CR150-2-1 U2 22 208 DN350 2850 3280 0 1770 345 2000 3491 C CR150-3-2 U2 30 280 DN350 2850 3280 1200 1961 345 2000 3855 C CR150-3 U2 37 3 DN350 2850 3280 10 2018 345 2000 87 C CR150-4-1 U2 45 4 DN350 2850 3280 10 2180 345 2000 4582 C CR150-5-2 U2 55 525 DN350 2850 3280 10 23 345 2000 5315 C CR150-2-1 U2 22 249 DN350 2850 3930 0 1770 345 2000 70 C CR150-3-2 U2 30 336 DN350 2850 3930 10 1961 345 2000 4534 C CR150-3 U2 37 432 DN350 2850 3930 10 2018 345 2000 4777 C CR150-4-1 U2 45 528 DN350 2850 3930 10 2180 345 2000 5381 C CR150-5-2 U2 55 630 DN350 2850 3930 10 23 345 2000 6257 C 74
Otional equiment ydro MPC All otional equiment, if required, must be secified when ordering the ydro MPC booster system, as it must be fitted from factory rior to delivery. Redundant rimary sensor Diahragm tank TM04 4125 0809 Fig. 56 Redundant rimary sensor In order to increase the reliability, a redundant rimary sensor can be connected as backu sensor for the rimary sensor. Note: The redundant rimary sensor must be of the same tye as the rimary sensor. Fig. 55 Diahragm tanks In buildings it is usually necessary to install a diahragm tank on the discharge side of the booster system. As standard, the ydro MPC booster system is designed for a maximum system ressure of 16 bar. A standard ydro MPC booster system includes ressure transmitters and one ressure gauge with a nominal ressure of 16 bar (full scale). TM02 9027 1904 Descrition Range [bar] Product number Redundant rimary sensor 1) 10 96741462 16 920350 1) The redundant rimary sensor is normally connected to analog inut AI3 of the CU 351. If this inut is used for another function, such as "External setoint", the redundant sensor must be connected to analog inut AI2. If, however, this inut is also occuied, the number of analog inuts must be increased by installing an IO 351B module. See age 79. ydro MPC booster systems designed for PN 16 Diahragm tanks u to 33 litres are mounted on the manifold on the discharge side of the booster system. For information about diahragm tanks larger than 25 litres, see Diahragm tank on age 82. Max. system Descrition ressure [bar] Diahragm tank and ydro MPC 16 booster system for PN 16 Volume [litres] Connection Product number 8 G 3/4 920346 12 G 3/4 920347 25 G 3/4 920348 75
Otional equiment ydro MPC Dry-running rotection The booster system must be rotected against dryrunning. The inlet conditions determine the tye of dry-running rotection: If the system draws from a tank or a it, select an electrode relay for dry-running rotection. If the system has an inlet ressure, select a ressure transmitter or a ressure switch for dryrunning rotection. Descrition Range [bar] Product number Dry-running rotection by means of electrode relay (without electrodes and electrode cable) 1) - 920079 Pressure switch 1) Inlet ressure sensor 2) 1) Only one tye of dry-running rotection can be selected, as it must be connected to the same digital inut of the CU 351. This also alies to level switches. For further information about the CU 351, see age 10. 2) The inlet ressure sensor is normally connected to analog inut AI2 of the CU 351. If this inut is used for another function, such as "External setoint", the sensor must be connected to analog inut AI3. If, however, this inut is also occuied, the number of analog inuts must be increased by installing an IO 351B module. See age 79. For further information about the IO 351B, see age 10. Pilot um Fig. 57 Pilot um 2 920071 4 920070 8 920072 16 920065 1 96155335 4 920074 6 920066 10 920075 16 920067 The ilot um takes over the oeration from the main ums in eriods when the consumtion is so small that the sto function of the main ums is activated. A ilot um is tyically used in booster systems as from 5.5 kw. Pilot ums are available for all control variants. TM04 4197 9 Pilot um Suly voltage [V] Byass connection Total height Fig. 58 Booster system with byass connection Product number CRIE 3-7 (0.55 kw) 1 x 220-2 520 97526996 CRIE 3-10 (0.75 kw) 1 x 220-2 620 97526998 CRIE 5-8 (1.1 kw) 1 x 220-2 656 97527000 CRIE 5-10 (1.5 kw) 3 x 0 776 97527011 A byass connection is a ie diversion consisting of a manifold, two isolating valves and a non-return valve. The byass connection allows water to byass the ums from the suction to the discharge manifold. We offer byass connections for the following ydro MPC systems: Descrition Connection Product number CRI(E) 3 (2 to 3 ums) CRI(E) 5 (2 to 3 ums) R 2 9697 CRI(E) 3 (4 to 6 ums) CRI(E) 5 (4 to 6 ums) R 2 1/2 966101 CRI(E) 10 (2 to 3 ums) R 2 1/2 966104 CRI(E) 10 (4 to 5 ums) DN 80 966106 CRI(E) 10 (6 ums) DN 966107 CRI(E) 15, 20 (2 ums) DN 80 966109 CRI(E) 15, 20 (3 to 4 ums) CR(E) 32 (2 ums) DN 966111 CR(E) 15, 20 (5 to 6 ums) CR(E) 32 (3 to 6 ums) DN 150 966112 CR(E) 45 (2 ums) CR(E) 64 (2 ums) DN 150 966113 CR(E) 45 (3 to 6 ums) CR(E) 64 (3 to 6 ums) DN 200 966114 CR(E) 90 (2 ums) DN 150 96417308 CR(E) 90 (3 to 4 ums) DN 200 96417306 CR(E) 90 (5 to 6 ums) DN 250 96417303 TM04 4126 0809 76
Otional equiment ydro MPC Position of non-return valve As standard, non-return valves are fitted on the discharge side of the ums of the booster system. In installations with suction lift, it is advisable to install non-return valves on the suction side of the ums to revent dry running. Descrition Product number Non-return valve on suction side 96615832 Stainless steel non-return valve As standard, the ydro MPC booster system includes non-return valves of olyoxymethylene (POM). Stainless steel non-return valves are available for umed liquids containing abrasive articles. Note: Order 1 valve for each um. Descrition 1) Connection Max. oerating ressure is 25 bar. Emergency oeration switch The emergency oeration switch enables emergency oeration if a fault occurs in the CU 351. Note: The motor rotection and the dry-running rotection are not activated during emergency oeration. Note: Order 1 switch for each um. Product number Non-return valve 1) CRI(E) 10 to CRI(E) 20 96499128 CRI(E) 3 to CRI(E) 5 96499127 CR(E) 32 to CR(E) 90 96499129 Descrition Location Product number CR(I)E ums 920 CR(I) um with external frequency converter In control cabinet 920099 CR(I) um for mains oeration 920098 Reair switch By means of a reair switch fitted to the individual ums of the ydro MPC booster system, the suly voltage to the um can be switched off during reair, etc. Note: Order 1 switch for each um. Descrition Motor current/ starting method Isolating switch Location By means of an isolating switch fitted inside the control cabinet, the suly voltage to the um can be switched off during reair etc. Note: This otion only alies to ydro MPC-F control variants. Note: Order 1 switch for each um. Product number 16 A, DOL 920262 > 16 A < 25 A, DOL 920263 > 25 A < A, DOL 920264 > A < 63 A, DOL 920265 > 63 A < 80 A, DOL 96616871 > 80 A < A, DOL 920267 > A < 125 A, DOL 920268 >125 A < 175 A, DOL 920269 Reair switch > 175 A < 250 A, DOL 920282 On the um 16 A, Y/Δ 920270 > 16 A < 25 A, Y/Δ 920271 > 25 A < A, Y/Δ 920272 > A < 63 A, Y/Δ 920273 > 63 A < 80 A, Y/Δ 920274 > 80 A < A, Y/Δ 920275 > A < 125 A, Y/Δ 920276 > 125 A < 175 A, Y/Δ 920277 > 175 A < 250 A, Y/Δ 920283 Descrition Isolating switch Motor current/ starting method Location Product number 16 A, DOL 920101 > 16 A < 25 A, DOL 920102 > 25 A < A, DOL 920103 > A < 63 A, DOL 920104 > 63 A < 80 A, DOL 920105 > 80 A < A, DOL 920106 > A < 125 A, DOL 920107 > 125 A < 175 A, DOL In control 920108 16 A, Y/Δ cabinet 920109 > 16 A < 25 A, Y/Δ 920110 > 25 A < A, Y/Δ 920111 > A < 63 A, Y/Δ 920112 > 63 A < 80 A, Y/D 920113 > 80 A < A, Y/Δ 920114 > A < 125 A, Y/Δ 920115 > 125 A < 175 A, Y/Δ 920116 77
Otional equiment ydro MPC Main switch with switching off of the neutral conductor Main switch with switching off of the neutral conductor is only used in connection with single-hase motors. This otion is to be selected according to the local rules for the installation site. As standard, the main switch does not switch off the neutral conductor. Descrition Main switch with switching off of the neutral conductor Nominal current of ydro MPC [A] Oerating light, system Location Product number 920023 920022 175 920021 250 920020 0 920019 630 In control cabinet 920018 800 920017 1250 920016 1750 920015 2000 920014 2500 920013 Oerating light, um Fig. Oerating light, system The oerating light is on when the relevant um is in oeration. Note: Order 1 oerating light for each um. Descrition Oerating light for Oerating light, um Location Examle: For a ydro MPC-ES booster system consisting of 1 CRIE um with integrated frequency converter and 2 mains-oerated CRI ums, order 1 oerating light No 920330 and 2 oerating lights No 920139. TM04 4112 0709 Product number ydro MPC-E In door of 920330 ydro MPC-F control 920136 ydro MPC-S cabinet 920139 Fig. 59 Oerating light, system The oerating light is on when the system is in oeration. Descrition Location Product number Oerating light, system In door of control cabinet 920286 TM04 4112 0709 Fault light, system Fig. 61 Fault light, system The fault light is on if a fault occurs in the system. Note: Phase failure causes no fault indication. TM04 3254 3908 Descrition Location Product number Fault light, system In door of control cabinet 920132 78
Otional equiment ydro MPC Fault light, um IO 351B interface TM04 3254 3908 Fig. 62 Fault light, um The fault light is on if a fault occurs in the um. Note: Order 1 fault light for each um. Descrition Fault indicator light for Location Fault light, um Panel light and socket Product number ydro MPC-E In door of control 920332 cabinet ydro MPC-F 920131 ydro MPC-S 920331 The anel light is on when the door of the control cabinet is oen. Panel lights for 50 z are in accordance with EN 529/ 10.91. Note: The anel light and socket are to be connected to a searate ower suly. Descrition Tye Location Panel light Product number 14 W, 2 V, 50 z, socket 920296 14 W, 220-230 V, 50 z, In control socket cabinet 920126 14 W, 120 V, z, socket 920076 Fig. 63 IO 351B interface This otion features a factory-fitted and nonrogrammed IO 351B interface enabling exchange of nine additional digital inuts, seven additional digital oututs and two additional analog inuts. Note: As standard the CU 351 suorts the installation of one IO 351B interface. Descrition Location Product number I/O interface via IO 351B In control cabinet 920259 Ethernet The ethernet connection makes it ossible to get unlimited access to the setting and monitoring of the ydro MPC from a remote PC. GrA 0815 Descrition Product number Ethernet 920338 79
Otional equiment ydro MPC GENIbus module The GENIbus module is an add-on module that enables data communication with external GENIbus devices, such as Grundfos CIU communication interfaces. Note: The GENIbus module is needed when you wish to transfer oerational data from the ydro MPC to a building management system. Descrition Location Product number GENIbus module In control cabinet 920339 CIU communication interface Note: This otion includes a CU 351 with a factoryfitted GENIbus module which is necessary for external data communication. Descrition Fieldbus rotocol Location Product number CIU 110 LON 96943635 CIU 150 PROFIBUS 96943636 CIU 200 Modbus RTU 96943637 In control cabinet CIU 250 GSM 96943638 CIU 271 GRM 96943639 CIU 300 BACnet 96943641 For further information about data communication via CIU units, data to transfer and fieldbus rotocols, see the CIU documentation available in WebCAPS. GrA 6118 Fig. 64 Grundfos CIU communication interface The CIU enables communication of oerating data, between the ydro MPC and a building management system. The CIU enables transfer of these data: oerating mode setoint control mode warnings and alarms ower/energy consumtion. We offer the following CIU units: CIU 110 For communication via LON. CIU 150 For communication via PROFIBUS. CIU 200 For communication via Modbus RTU. CIU 250 For communication via GSM. CIU 271 For communication via Grundfos Remote Management (GRM). CIU 300 For communication via BACnet. 80
Otional equiment ydro MPC Transient voltage rotection The transient voltage rotection rotects the booster system against high-energy transients. Descrition Transient voltage rotection Lightning rotection Range The booster system can be rotected against strokes of lightning. The lightning rotection is in accordance with IEC 61024-1: 1992-10, class B and C. Note: Additional earthing facilities must be arranged by the customer at the site of installation. Descrition Lightning rotection Phase failure monitoring Product number 3 x 0 V, N, PE, 50/ z 920181 3 x 0 V, PE, 50/ z 920182 Range Product number 3 x 0 V, N, PE, 50/ z 920125 3 x 0 V, PE, 50/ z 920180 The booster system should be rotected against hase failure. Note: A otential-free switch is available for external monitoring. Descrition Location Product number Phase-failure monitoring In controller 920117 Voltmeter A voltmeter indicates the mains voltage between the mains hases and between the neutral conductor, N, and the mains hases. Note: Order 1 voltmeter for each um. Descrition Voltmeter, 500 V (2 hases) Voltmeter, 500 V, with changeover switch (all hases) Ammeter Location In door of control cabinet An ammeter indicates the current of one hase er um. Note: Order 1 ammeter for each um. Descrition Current [A] Location Ammeter Product number 920118 920119 Product number 6 920120 16 920121 25 920284 In door of control 920122 cabinet 920123 1 920124 250 920285 0 920281 Beacon The beacon is on in case of a system alarm. Note: Phase failure causes no alarm indication. Descrition Beacon Location Product number On to of control cabinet 920176 External 1) 920177 1) Cable is not included. Audible alarm The audible alarm sounds in case of a system alarm. Descrition Audible alarm Sound ressure level Location Product number 80 db(a) 920178 In control cabinet db(a) 920179 81
Accessories ydro MPC All accessories can be fitted on the ydro MPC booster system after delivery. Dry-running rotection The booster system must be rotected against dryrunning. Dry-running rotection by means of level switches is used in installations where the booster system draws water from a tank or well. Descrition Product number Level switch including 5 metres of cable 1) 920142 1) The inut for level switch is not included. See age 76. Only one tye of dry-running rotection can be selected, as it must be connected to the same digital inut of the CU 351. This also alies to level switches. Diahragm tank Diahragm tank, 10 bar Caacity [litres] Connection Product number 8 G 3/4 96528335 12 G 3/4 96528336 18 G 3/4 96528337 24 G 1 96528339 33 G 1 965283 G 1 96528341 80 G 1 96528342 G 1 96528343 130 G 1 96528344 170 G 1 96528345 2 G 1 96528346 300 G 1 96528347 450 G 1 96528348 0 G 1 1/2 963451 800 G 1 1/2 963452 0 G 1 1/2 963453 1500 DN 65 96573283 2000 DN 65 96573284 3000 DN 65 96573285 Diahragm tank, 16 bar Fig. 65 Diahragm tanks A diahragm tank must always be installed on the discharge side of the booster system. TM02 9097 1904 Caacity [litres] Connection Product number 8 G 3/4 96573347 12 G 3/4 96573348 25 G 3/4 96573349 80 G 1 963420 G 1 963421 200 G 1 1/4 963422 300 G 1 1/2 963423 0 G 1 1/2 963424 500 G 1 1/2 963425 0 G 1 1/2 963426 800 G 1 1/2 963427 0 G 1 1/2 963428 Note: The diahragm tanks are searate tanks without valve, fittings and ies. 82
Accessories ydro MPC Foot valve Machine shoe TM04 3245 3908 Fig. 66 Foot valves The booster system must be rotected against dry running. Dry-running rotection by means of level switches is used in installations where the booster system draws water from a tank or well. Foot valves are tyically used in minor booster systems with suction lift. For examle when the ydro MPC draws water from a break tank laced at a lower geodetic height than the booster system. Foot valves are designed to ensure otimal suction conditions. Descrition Connection Product number Foot valve R 2 956120 R 3 956130 R 4 956449 TM04 4128 0809 Fig. 67 Machine shoes Machine shoes reduce any vibrations from the system to the floor, allowing the system to be height-adjusted by ± 20 mm. Descrition ydro MPC with Product number Machine shoe CRI(E) 1 to CRI(E) 3 96412344 CRI(E) 10 to CRI(E) 20 96412345 CR(E) 32 to CR(E) 90 96412347 Note: The roduct number covers one (1) machine shoe. Extra documentation The documents and ublication numbers below refer to rinted documentation of ydro MPC (grou versions). Document Publication number Data booklets ydro MPC, z 9659 Installation and oerating instruction ydro MPC 965907 Quick guide ydro MPC 965941 Catalogue ydro booster systems - Custom-built 96881732 solutions 50/ z In addition to rinted documentation, Grundfos offers roduct documentation in WebCAPS on Grundfos homeage, www.grundfos.com. See age 85. 83
Alternative booster systems ydro MPC Alternative booster systems Booster system ydro Multi-E Data and features Max. head 10 to m Flow rate 2 to 85 m 3 /h Max. oerating ressure 16 bar Number of ums 2 to 3 Pum tyes CRE Features Secially designed for water suly in buildings. % adatation to consumtion. Easy to install and commission. Small foot rint. Data communication via Grundfos R remote control. GrA0762 ydro Multi-S ydro Solo-E/-S GrA5733 - GrA5734 Max. head 9 to 103 m Flow rate 0.5-69 m 3 /h Max. oerating ressure 16 bar Number of ums 2 to 3 Pum tyes CR, C Features Secially designed for water suly in buildings. % adatation to consumtion. Easy to install and commission. Small foot rint. Data communication via Grundfos R, etc. Max. head 10 to m Flow rate 2 to 55 m 3 /h Max. oerating ressure 16 bar Number of ums 1 Pum tyes CRE, CR 1) Features Easy to install and commission. Constant ressure. Data communication via Grundfos R remote control. 2) Gr5164 - Gr5165 1) ydro Solo-E is equied with a CRE um; ydro Solo-S with a CR um. 2) Alies only to ydro Solo-E. 84
Further roduct documentation ydro MPC WebCAPS WebCAPS is a Web-based Comuter Aided Product Selection rogram available on www.grundfos.com. WebCAPS contains detailed information on more than 185,000 Grundfos roducts in more than 20 languages. In WebCAPS, all information is divided into 6 sections: Catalogue Literature Service Sizing Relacement CAD drawings. Catalogue This section is based on fields of alication and um tyes, and contains technical data curves (Q, Eta, P1, P2, etc.) which can be adated to the density and viscosity of the umed liquid and show the number of ums in oeration roduct hotos dimensional drawings wiring diagrams quotation texts, etc. Literature In this section you can access all the latest documents of a given um, such as data booklets installation and oerating instructions service documentation, such as Service kit catalogue and Service kit instructions quick guides roduct brochures. Service This section contains an easy-to-use interactive service catalogue. ere you can find and identify service arts of both existing and discontinued Grundfos ums. Furthermore, this section contains service videos showing you how to relace service arts. 85
0 1 Further roduct documentation ydro MPC Sizing This section is based on different fields of alication and installation examles, and gives easy ste-by-ste instructions in how to select the most suitable and efficient um for your installation carry out advanced calculations based on energy consumtion, ayback eriods, load rofiles, life cycle costs, etc. analyse your selected um via the built-in life cycle cost tool determine the flow velocity in wastewater alications, etc. Relacement In this section you find a guide to selecting and comaring relacement data of an installed um in order to relace the um with a more efficient Grundfos um. The section contains relacement data of a wide range of ums roduced by other manufacturers than Grundfos. Based on an easy ste-by-ste guide, you can comare Grundfos ums with the one you have installed on your site. When you have secified the installed um, the guide will suggest a number of Grundfos ums which can imrove both comfort and efficiency. CAD drawings In this section it is ossible to download 2-dimensional (2D) and 3- dimensional (3D) CAD drawings of most Grundfos ums. These formats are available in WebCAPS: 2-dimensional drawings:.dxf, wireframe drawings.dwg, wireframe drawings. 3-dimensional drawings:.dwg, wireframe drawings (without surfaces).st, solid drawings (with surfaces).ert, E-drawings. WinCAPS WinCAPS is a Windows-based Comuter Aided Product Selection rogram containing detailed information on more than 185,000 Grundfos roducts in more than 20 languages. The rogram contains the same features and functions as WebCAPS, but is an ideal solution if no Internet connection is available. WinCAPS is available on CD-ROM and udated once a year. Fig. 68 WinCAPS CD-ROM Subject to alterations. 86