DC610 Series Multi-Sized 1 thru 6 DC610 Series Half-Size 1 thru 6 Installation Instructions Universal Closers with Heavy Duty Spring Stop Parallel Arms A11 - Non- Arm A1 - Arm STANDARD APPLICATION WITH DEEP REVEAL APPLICATION WITH M103 OPTION(615F59 CLAMP KIT) FLUSH PARTITION APPLICATION WITH M10 OPTION (615F60 ) IMPORTANT: An improperly installed or incorrectly adjusted door closer may cause property damage or personal injury; and will void product warranty. To avoid personal injury, DO NOT DISASSEMBLE THIS CLOSER BODY. closers must be securely fastened to a properly reinforced door and frame with fasteners provided. closers with a HOLD OPEN ARM (A1) are not permitted to be installed in fire door assemblies. and frame must be specifically templated for 85,, 95, 100, 105 or 110 door swing. Type of Installation Interior Parallel Arm ' " ' 6" 3' 0" 3' 6" ' 0" ' 6" Size of & Closer Exterior In -swinging Exterior Out -swinging ' 6" 3' 0" *3' 6" *' 0" Recommended Closer Size 1 3 5 6 **Max. Opening lbs/f 8 1 16 6 RHR TO DETERMINE HAND OF YOUR : LEFT HAND RIGHT HAND LHR *DC610 Series Recommended **NOTE: These forces are for standard templating with bearing type hinges and do not account for pressure differentials and draft. Half size closers DC610 are capable of being adjusted to next higher setting. 80-9360-6003-15 Rev. 07/1
Parallel Arm Application A11 or A1 Arm SEE CHART TO SELECT DEGREE OF OPENING AND WIDTH FOR YOUR. THEN, DETERMINE FRAME CONDITION: STANDARD & DEEP REVEAL (use Dim s. A & B) or FLUSH PARTITION (use Dim s A & C) *Dimension C is only used for Flush Partition application (Frame Template 1C). S 8 " TO 3 S 33 " TO 1 S " TO 8 Opening 615F5 NHO ARM (A11) 615F5 NHO ARM (A11) 615F56 NHO ARM (A11) 615F51 HO ARM (A1) 615F53 HO ARM (A1) 615F55 HO ARM (A1) HOLD OPEN 85 95 100 105 110 DEAD STOP 95 100 105 110 115 Dim. A 11 (79) 10-1/(67) 10 (5) 9-1/ (1) 9 (9) 8-1/ (16) 1. Templates Mark (for closer bracket) and Jamb (for arm bracket). FRAME TEMPLATE 1A (Standard Application with Bracket) For Deep use Frame Template 1B (Page 3). For Flush Partition use Frame Template 1C (Page 3). Frame s 1-7/8 " to -5/8 " (8mm to 117mm) Dim. B *Dim. C 10 (5) 10-1/8(57) 9-1/ (1) 9-5/8 () 9 (9) 9-1/8 (3) 8-1/ (16) 8-5/8 (19) 8 (03) 8-1/8 (06) 7-1/ (191) 7-5/8 (19) Dim. A Dim. B *Dim. C Dim. A Dim. B *Dim. C 13-1/8(333) 1-5/8(31) 1 (305) 11-5/8(95) 11 (79) 10-1/(67) FRAME STOP REVEAL 1-1/(311) 11-5/8(95) 11-1/8(83) 10-5/8(70) 10-1/8(57) 9-1/ (1) 7/16 (11.1) FRAME STOP TOP OF 1-(31) 11-3/(98) 11-1/(86) 10-3/(73) 10-1/(60) 9-5/8 () (50.8) 1-1/ (31.8) 15-1/8(38) 1-1/(368) 13-7/8(35) 13-1/(337) 1-3/(3) 1-1/(311) 3/ (19) -3/ (70) 1-(365) 13-3/(39) 13-1/8(333) 1-1/(318) 1-1/8(308) 11-1/(9) B TYP. (9.5) HINGE 1/ OR C L (1.7) PIVOT 1-1/(368) 13-7/8(35) 13-1/(337) 1-5/8(31) 1-1/(311) 11-5/8(95) Template is Typical for all Frame Templates 1A, 1B, and 1C MOUNTING SCREW SPECIFICATIONS ARM AND CLOSER 1/-0 oval head machine screw or 1/-1 self-drilling screw. 3/16 (.8) diameter pilot hole required for Wood Applications. CLOSER NOTES: Check hand of door, see page 1. Right Hand Application Shown Left Hand Opposite 1 (5.) Dimensions given in inches (mm). Do Not Scale Drawing. Closer must be installed in a true horizontal plane to ensure proper closer performance. }or{option M5: Sex nuts, furnished when ordered Drill thru 9/3 (7.1) Enlarge to (9.5) Dia. This Side Only ( Places) -5/16 (109.5) L 1/-0 THREAD (10) 1-1/8 (9) -3/ (70) A THICKNESS " 1- (35mm) 1-3/ " (mm) & OVER SEX NUT LENGTH L 1-9/3 " (33mm) 1-1/3 " (mm) 80-9360-6003-15 Rev. 07/1 Page
Parallel Arm Application A11 or A1 Arm FRAME TEMPLATE 1B DEEP REVEAL APPLICATION with M103 OPTION (615F59 CLAMP KIT) -3/ Frame s Over -5/8 " (117mm) B HINGE FRAME STOP (70) C L OR TYP. PIVOT (50.8) (9.5) FRAME CLAMP REVEAL 7/16 (11.1) - (111.1) -1/8 (5) 1/ (1.7) 615F59 CLAMP (TYP) 5/16 (8) SPACER CLAMP Clamps Only Clamps with Spacer FRAME FRAME TEMPLATE 1C FLUSH PARTITION APPLICATION with M10 OPTION (615F60 ) 3/ (19.1) Frame s 0 to 1/8 (0mm to 3mm) C " " 615F60 Frame 1-3/ () 1-1/ (38.1) -1/ (63.5) 1/ (1.7). Install Closer Bracket 3. Mount Closer Body to Closer Bracket 1/-1 x 1-1/ OH Self-Drilling () or 1/-0 x 3/ OHMS w/ Sex Nuts () (M5 Option) Pin Hole End Countersunk Hole End Holding Pins 1/-0 x 1/ OHMS () 80-9360-6003-15 Rev. 07/1 Page 3
Parallel Arm Application A11 or A1 Arm. Connect Arm To Closer Using hex wrench provided, close (turn clockwise) CLOSING SPEED VALVE (see page for location on closer). DO NOT OVER TIGHTEN. Open door to approximately 60 Using wrench on underside of spindle, rotate spindle approximately 135 toward hinge edge of door. Install arm on spindle at an approximate angle to door. Reopen CLOSING SPEED VALVE. Install and tighten arm washer and screw. ARM ALL ANGLES SHOWN ARE APPROXIMATE 60 135 WRENCH Rotate 135 SPINDLE SPINDLE AT REST ARM CENTERLINE SPINDLE ROTATED 135 HOLD OPEN ADJUSTMENTS - A1 ARMS ONLY On Rotate Off To Decrease To Increase 80-9360-6003-15 Rev. 07/1 Page
Spring Power Adjustment Locate spring power adjuster from Illustration below DC600 Half Size Adjustment as Desired DC600 Size 1 thru 6 Adjustment See Chart DC600 SPRING POWER ADJUSTMENT CHART All DC600 closers are factory set at an approximate Size 3. Adjust closer as necessary for door size using this chart. Readjustment may be required to suit prevailing conditions. CLOSING SPEED VALVE SPRING POWER ADJUSTER (5/16 WRENCH or SOCKET) " OPTION M71 DELAYED ACTION VALVE BACKCHECK LOCATION VALVE BACKCHECK INTENSITY VALVE (FLAT TIP SCREWDRIVER W/ 5 " (17mm) Min. Shaft Length) Interior (71) 6 (76) 3 0 (915) 3 6 (1067) Size of Exterior Exterior In Out Swing Swing 6 (76) 3 0 (915) 3 6 (1067) 6 (76) ' 0 " (119) 3 0 (915) No. of Full (360 ) Turns Clockwise of Power Adjuster 8 1 16 Date Stamp Equivalent Closer Size (Approx.) 3 5 LATCHING SPEED VALVE Power Size Stamp Latch Closing Speed De la ye Action Option M-71 d Backcheck Closing Speed Valve (3/3 Allen Wrench Provided) To adjust speed of door closing from fully open to a position " to 5 from closed, turn Closing Speed Valve CLOCKWISE to SLOW closing, COUNTER-CLOCKWISE to SPEED closing. Latching Speed Valve (3/3 Allen Wrench Provided) After closing speed has been obtained, turn latching speed valve CLOCKWISE to SLOW latching or COUNTER-CLOCKWISE to SPEED latching for last " to 5 " of door travel. NOTE: Set combination of CLOSING and LATCHING speeds to between 3 and 7 seconds Use of door by handicapped, elderly or small children, may require even greater closing time. Backcheck Location Valve (3/3 Allen Wrench Provided) Valve is closed, as shipped, from factory. To increase the degree of door opening where backcheck takes effect, turn valve counter-clockwise. VALVE CLOSED OCCURS AT 65-70 OPEN 95-100 Degrees shown are approximate Backcheck Intensity Valve Turn valve COUNTER- CLOCKWISE to reduce backcheck or CLOCKWISE to increase backcheck. (Backcheck should be set to give a soft cushioning action, not a sudden stop). Installing Cover Full Cover (Standard) Slip cover over closer. Hold tightly against closer mounting surface. Secure on each side with 6-3 x 1/ " PBHMS screws. Delayed Action Valve (3/3 Allen Wrench Provided) Turn valve CLOCKWISE to SLOW closing, COUNTER- CLOCKWISE to SPEED closing. Delayed action may be adjusted from 0 seconds to 90 seconds, depending on degree of door swing. Delay occurs at the beginning of the door closing cycle from fully open down to 70, where the closing speed valve then begins its control. Copyright 006, 01 Corbin Russwin, Inc., an Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Corbin Russwin, Inc. is prohibited. 80-9360-6003-15 Rev. 07/1 Page 5