INSTRUCTIONS FOR OUTDOOR WALL LANTERN, MODEL LPT-1032 Page 1
Thank you for purchasing this Langport Lighting outdoor wall lantern. This product has been manufactured with the highest standards of safety and quality. FEATURES: Easy to install Solid cast aluminum to resist the elements For energy savings this fixture has been engineered to safely use a Self Ballasted Compact Fluorescent Lamp in place of an incandescent lamp. GENERAL: Questions, Problems, Missing Parts? Please contact our Customer Service Team at 1-877-698-2157. Customer service hours are Monday through Friday, between 8 AM and 5 PM Pacific time. You may also contact us via fax at 1-310-886-3719 or e-mail at Info@Langportlighting.com. KEEP this instruction manual. KEEP your receipt for proof of purchase. TOOLS AND ITEMS REQUIRED FOR INSTALLATION AND ASSEMBLY (NOT INCLUDED): SAFETY GOOGLES #2 PHILIPS SCREWDRIVER PLIERS LIGHT BULB (100 WATT MAX OR CFL EQUIVALENT) ELECTRICAL TAPE WIRE CUTTERS WIRE STRIPPERS Page 2
PARTS: Remove fixture and mounting package from box and make sure that parts are are not missing by referencing illustrations below. (Parts are not to scale.) HOOD BRACKET MOUNTING SCREWS (2) WIRE NUTS (3) MOUNTING BRACKET HOOD SCREWS (2) NIPPLE MAIN FIXTURE BODY SCREWS (4) HEX NUT CLIPS (4) GLASS S (4) LOCK NUT Page 3
CAUTION: All electrical connections must be in accordance with local and National Electrical Code (N.E.C.) standards. If you are unfamiliar with proper electrical practices, obtain services of a qualified electrician. Turn off the main power at circuit breaker before installing fixture, in order to prevent possible shock. Before cleaning fixture, turn off power and allow several minutes for the fixture to cool down. BEFORE YOU BEGIN: The OUTLET BOX described in the following section is not provided. To install this fixture, a standard OUTLET BOX needs to be pre-installed at the selected mounting location. Power supply wires need to be run into the OUTLET BOX, extending approximately 6 from its opening. If an OUTLET BOX does not exist, contact a qualified electrician to have one installed. ASSEMBLY AND INSTALLATION: 1. DISCONNECT POWER AT THE CIRCUIT BREAKER. 2. Thread the HEX NUT onto the NIPPLE. Thread the NIPPLE into the center hole of the MOUNTING BRACKET. Do not tighten the HEX NUT at this time. (FIG. 1) 3. Pull the power supply wires out from the OUTLET BOX, and attach the MOUNTING BRACKET to the OUTLET BOX, using the BRACKET MOUNTING SCREWS. (FIG. 1) 4. Strip approximately ¼ of insulation from each supply wire from the OUTLET BOX. Raise the MAIN FIXTURE BODY to the wall, bringing the WALL PLATE close to the OUTLET BOX. Make the following wire connections using the WIRE NUTS (FIG. 1): WHITE (NEUTRAL) SUPPLY WRE to WHITE FIXTURE WIRE BLACK (HOT) SUPPLY WIRE to BLACK FIXTURE WIRE SUPPLY GROUND WIRE to FIXTURE GROUND WIRE Wrap each wire connection with 2 of electrical tape. 5. Place the WALL PLATE over the OUTLET BOX, making sure the NIPPLE feeds through the hole of the WALL PLATE. Adjust the NIPPLE until it protrudes out from the WALL PLATE ¼. Remove the WALL PLATE and secure the position of the NIPPLE by tightening the HEX NUT against the MOUNTING BRACKET. (FIG. 1) 6. Carefully tuck all WIRES and WIRE NUTS into the OUTLET BOX. Place the WALL PLATE back onto the NIPPLE, and secure it into place using the LOCK NUT. (FIG. 1) Page 4
ASSEMBLY AND INSTALLATION (CONT.): WALL PLATE WHITE FIXTURE WIRE BRACKET MOUNTING SCREW NIPPLE HEX NUT MOUNTING BRACKET BLACK (HOT) SUPPLY WIRE LOCK NUT BLACK FIXTURE WIRE FIXTURE GROUND WRE WIRE NUT SUPPLY GROUND WRE WHITE OUTLET (NEUTRAL) BOX SUPPLY WRE FIG. 1 7. Slide the four GLASS S into the CAGE. Secure each GLASS with a CLIP and SCREW, as shown. (FIG. 2) Page 5
ASSEMBLY AND INSTALLATION (CONT.): SCREW CLIP GLASS CAGE FIG. 2 8. Install an incandescent LIGHT BULB or a Listed SBCFL (Self-Ballasted Compact Fluorescent Lamp [not provided]) into the socket of the CAGE. Do not exceed a 100 Watt incandescent LIGHT BULB, or a 26 Watt SBCFL.. (FIG. 3) Page 6
ASSEMBLY AND INSTALLATION (CONT.): 9. Slide the HOOD onto the CAGE and secure it in place using the HOOD SCREWS. (FIG. 3) HOOD LIGHT BULB CAGE HOOD SCREW FIG. 3 10. After installing the fixture, caulk the upper 2/3s of the WALL PLATE to the mounting surface. Leave the bottom 1/3 un-caulked to allow for drainage of any water that might leak into the enclosure. The manufacturer recommends a non-drying exterior caulking material. A good example is a clear silicone rubber sealant for exterior use. 11. RESTORE POWER AT THE CIRCUIT BREAKER. Turn on the wall switch. Page 7
TROUBLESHOOTING: SYMPTOM POSSIBLE CAUSE CORRECTIVE ACTION Lights will not turn on. 1. Power is off. 1. Make sure power supply is on. 2. Faulty switch. 2. Test or replace switch. 3. Faulty wire connection. 3. Check wiring. Fuse blows or circuit breaker trips when light is turned on. 1. Crossed wires or power wire is grounding out. 1. Check wire connections. PRODUCT MAINTENANCE: To clean the fixture, disconnect power to the fixture by turning off the circuit breaker or by removing the fuse at the fuse box. Wait a few minutes for the fixture to cool down. Use a dry or slightly dampened clean cloth (use clean water, never a solvent) to wipe the glass and surface of the fixture. Do not use any cleaners with chemicals, solvents or harsh abrasives. If necessary, use a mild soap to clean off any dirt or stains. ONE YEAR LIMITED WARRANTY Patriot Lighting warrants this product to be free from defects in material and workmanship for one year from the original date of purchase by the consumer. This warranty is limited to the counter replacement at the time of purchase, with the original purchase receipt. Patriot Lighting will not be liable for the loss or damage of any kind, incidental or consequential damages of any kind, whether based on warranty contract or negligence, and arising in connection with the sale, use or repair of the product claimed to be defective. Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation may not apply to you. This warranty gives you specific legal rights and you may also have other rights, which vary from state to state. Misuse, accident, improper installation or maintenance will also void the warranty. Page 8