systems Systems Emergency Lighting Inverter 120 or 277V 60 Hz Power

systems Systems Emergency Lighting Inverter 120 or 277V 60 Hz Power

RATINGS TABLE Size Batteries Volts S = Series SP = Series Parallel Total Weight 525 2 24 V S 153 700 4 48 V S 193 1000 4 48 V S 444 1250 4 48 V S 516 1500 4 48 V S 516 1800 8 48 V SP 648 2000 8 48 V SP 648 2200 8 48 V SP 648 2600 8 96 V S 792 3000 8 96 V S 792 3400 8 96 V S 792 3500 16 96 V SP 918 3800 16 96 V SP 1126 4000 16 96 V SP 1126 4500 16 96 V SP 1126 4800 16 96 V SP 1126 APPLICATIONS Airports Apartments/Condominium Complexes Assisted Living Centers Banks, Financial Casinos City, County, State, Federal Buildings Grocery Stores Hospitals Hotels Industrial Medical Offices Military Complexes Movie Theaters Office Buildings Parking Garages Prisons Race Tracks Train, Subway, Bus Stations Religious Facilities Restaurants Department Stores Schools, Colleges Shopping malls Sport facilities Superstores Tunnel and Toll Bridges 1

Dimensions for A: Up to 3.4kW 26W X 38H x 19D 38 Dimensions for B: Up to 4.8kW 26W X 62H x 19D 26 19 38 62 26 19 62 26 19 26 19 2

System Overview: The GNS Series Inverter maintain efficient AC Emergency Power to operate all emergency lighting fixtures at full-light output providing superior dependability and security to commercial/ industrial environments in a small footprint. The GNS Series Emergency Lighting Inverter from IEP Systems is designed to provide power to emergency and other critical loads in the event of a power failure or brownout situation. The line voltage output allows the remote fixtures to be located up to 2000 feet from the unit. Power Factor:.9 leading to.9 lagging GNS series inverter is designed to occupy a minimum footprint and has a separate compartment for main electronics and for batteries. The GNS series is a compact, modular emergency lighting inverter. Typical applications include all types of LED, fluorescent, incandescent, quartz restrike and low voltage lighting. The modular design and low MTTR (mean-time-to-repair) ensure easy maintenance. The GNS is well suited for stairwell, hallway, and outdoor emergency egress lighting, medium size office buildings and warehouses. GNS Series inverter employs premium (*VRLA) batteries, designed with an expected service life of 10 years per battery manufacturer guidelines. Theory of Operation: The GNS is designed to power the emergency egress lighting at full brightness for 90 minutes. The system is installed between the lighting distribution panel and the emergency circuit (s) and ahead of any local switches. Upon failure of the normal power source to the connected lights, the GNS will continue to power the emergency fixtures connected to it for a minimum of 90 minutes utilizing standard building lighting components. When the normal power is restored the GNS will automatically switch the lighting fixtures back to the normal source and recharge the batteries so that they are ready for the next power outage. The system may also be configured for normally off or for switched load capability as an option. Applications: The GNS Series Inverter will operate incandescent, fluorescent, and LED lamps with power factor greater than.9. *Self ballasted compact fluorescent and replacement LED screw in lamps may be used provided they have rated power factor of.9 or greater. *We recommend that only Energy Star recognized compact fluorescent or LED lamps be used with this equipment. *VRLA do not need to be watered. Periodic checks, coupled with standard record keeping and maintenance of the inverter would ensure the longevity of the battery module. Battery: Sealed, maintenance-free, lead calcium (AGM) batteries with10 year prorated warranty. The GNS employs Smart Battery Monitoring System which is temperature compensated and maintains maximum run-time and battery life. 3

Order Information GNS 700 120 120 OPTIONS GNS GNS Series Pure Sine Wave Lighting Inverter Watts 525 700 1000 1250 1500 1800 2000 2200 2600 3000 3400 3500 3800 4000 4500 4800 AC Input 120V 277V AC Output RUNTIME 120V (Other than 90 Minutes) 277V R30-30 Minutes R120-120 Minutes OUTPUT BREAKERS Example A 20 06 POLE A-1-Pole OC OPTIONS F- Fast Charge I - Inverter on Dry Form C Contact S - Summary Dry Form C Contacts T - Output Trip (supervised) Alarm Z - Seismic Mounting QTY maximum 6 pole positions WARRANTY 1-Year full warranty on system electronics. Bat tery warranty 1-year with 9-years prorata. Maintenance contracts available N - normally on O - normally off S - switched (Distribution Breakers) 10, 16, 20, 25, 32, 40, 50, 63 Note: 20 Amp output breakers standard unless otherwise ordered. A: PO Box 20302 Lehigh Valley PA 18002 V: (610) 628 1488 W: www.iepsystems.com E: info@iepsys.com 4

OVERVIEW: white powder coated paint Transformer Circuit Breaker Terminal Block Main Circut Board Display Panel Fan Ground 5

Call Today: 601.628.1488 6

Operating Parameters: Run Time: minimum 90 minutes Housing: Heavy duty steel construction finished in powder coat paint. Environment: Operating temperature: 32F (0C) 104F (40C) Altitude: 10,000 feet above sea level without derating Storage temperature: -20 to 70 degrees C. Note batteries will require frequent recharging if stored above 35 degrees C. Options: Suffix NOR - Normally off relay 1 required per every 20 amps of load (coil voltage matches input voltage of unit). Suffix ITP Input breaker trip alarm Suffix OTP Output breaker trip alarm, 1 per output breaker Suffix BTP Battery breaker trip alarm Suffix OCB_ Additional output circuit breakers (note 20 amp output breakers are standard unless otherwise specified. Suffix R30 - Battery capacity of 30 minutes for when the system is used with a permanently installed emergency generator. Suffix R120 Battery capacity of 120 minutes ( may require additional enclosures depending on the rating of the unit). Suffix RS232 - Suffix 208 or 240 or multiple voltage outputs may require additional cabinets. Standard features: footprint 26W by 18D for all models. Floor or wall mountable (with optional kit). 16 gauge cold-rolled steel construction finished in powder coat paint. PWM/MOSFET technology, low THD with high reliability and high efficiency. MTTR of less than 30 minutes for any one component. ETL listed to UL 924, meets or exceeds the requirements of OSHA, NEC, NFPA and other codes Input, one output and battery circuit breakers standard. Additional output breakers are optional. Two door access to electrical/electronic cabinet for ease of installation, wiring and maintenance. Front mounted meter panel for intuitive system status. Basic alarms for overload, overload shutdown, high temperature, near low battery and low battery shutdown. 2 knockouts furnished for contractor access. 98% efficiency on standby. Fan operation is de pendent upon internal temperature and battery condition to elongate fans useful service life. Power Rating Capacity: 350W 4800W single phase output with latest PWM technology to provide the most advanced performance and reliability. Input: 120V, 208V, 240V or 277V input 60Hz* Output: 120V, 208V, 277V or 120/277 VAC true on-line design Efficiency: >98% efficient at 100% linear load Electronics: Microprocessor controlled; recharge and overcharge protection standard 7

Specifications: Input: Voltage: 120 or 277 VAC 2 wire plus ground +/- 15% Frequency: 60 Hz +/- 3 Hz Protection: Circuit Breaker Output: Voltage: 120 or 277 VAC 2 wire plus ground Frequency: 60 Hz +/-.5 Hz THD: > 3% Linear load Regulation: +/- 3% for 50% load change Inverter overload: 110% for 5 minutes Protection: Output Circuit Breaker Battery: Type: Premium 10 year design life Valve Regulated Lead Acid (VRLA) Voltage: See chart for string voltage and number of strings Protection: Battery circuit breaker Lamps and Loads: Emergency power provides FULL LIGHT OUTPUT from all lamps and fixtures for the entire run-time. GNS Series Inverter operates fluorescent, CFL, incandescent, quartz, LED and other approved lamp types and loads. Protection: Provides overload, surge and undercurrent protection. Surge protection against load surges as defined in ANSI/IEEE C62.45 category A and B. Diagnostics and Maintenance: GNS Series On-board Monitoring System provides complete self checking capabilities and LED Indicator light Monitor. Informative advanced Metering Display and Alarms keep you in control of your emergency lighting environ ment 24/7. Automatically performs checking ensuring a safely lighted environment prior to an emergency Single point of testing instead of hundreds with battery packs. Cabinet: Space saving small footprint Free Standing Indoor NEMA 1 enclosure with modular design enables flexible installation. Installation: Modular design and small footprint allow easy installation in electrical closet or other convenient locations. Extended warranty available Warranty: 1-Year full warranty on system electronics. Bat tery warranty 1-year with 9-years prorata. Maintenance contracts available. Codes: Listed to UL 924, NFPA 101, NFPA 70, NEC and OSHA 8

systems GNS Series Sine Wave CONTACT US IEP Systems A PO Box 20302 Lehigh Valley PA 18002 P tel.:(610) 628 1488 W website: www.iepsys.com E e-mail: info@iepsys.com

CONTACT US IEP Systems A PO Box 20302 Lehigh Valley PA 18002 P tel.:(610) 628 1488 W website: www.iepsystems.com E e-mail: info@iepsys.com System W H D Dimensions A 22.75 8.75 6 B 23 12 9 C 23 18 9 HEADING Add text to a document by typing or by pasting or placing text from a word-processing application. If your word-processing application supports drag-and-drop, you can also drag text into InDesign frames. For large blocks of text, the Place command is an efficient, versatile way to add text to your document. InDesign supports a variety of word-processing, spreadsheet, and text file formats. When you place or paste text, you do not need to create a text frame first; InDesign will create one for you automatically. Add text to a document by typing or by pasting or placing text from a word-processing application. If your word-processing application supports drag-and-drop, you can also drag text into InDesign frames. For large blocks of text, the Place command is an efficient, versatile way to add text to your document. InDesign supports a variety of word-processing, spreadsheet, and text file formats. When you place or paste text, you do not need to create a text frame first; InDesign will create one for you automatically.