SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 HP PELZER MATERIALS TESTING LABORATORY 1175 Crooks Road Troy, MI 48084 Renata Machnik Phone: 248 280 2500 x176 MECHANICAL Valid To: November 30, 2018 Certificate Number: 1976.01 In recognition of the successful completion of the A2LA evaluation process, accreditation is granted to this laboratory to perform the following tests on automotive interior trim components: Test Test Method(s) 1 Abrasion (Taber) SAE J1530; Chrysler CLP 463 KB-21-01; GM 9337P; GMW 3208; Ford FLTM BN108-02; ASTM D3884 Adhesion Test ASTM D903, D413, D751 (Sections 45-48); Chrysler CLP 463 LB-10-01; Ford FLTM BN 151-05, 113-01; GMW 16596 (Section 3.4.1.3), GMW 14892 (Sections 3.1, 5.1); DIN 53357 Ash Content ASTM D1278 (Sections 14-17) Bearding SAE J1530 (Section 5.0) Charpy Impact (Unnotched Specimen) ISO 179-1 Cleanability Cold Cracking Chrysler CLP 463 KC-04-01; Ford FLTM BN 112-08; GMW 3026 (Section 3.4.7), 3402 Chrysler CLP 463 LB-11-01 (Methods A and B); GMW 3026 (Section 3.3.6), 14108, 14171; SAE J323; DBL 5306 (Sections 7.2, 7.3) (A2LA Cert. No. 1976.01) 11/28/2016 Page 1 of 4
Color Evaluation ASTM D6290; SAE J1767, J361; Chrysler CS-9022; Ford FLTM BI 109-01 Compression Set Corrosion ASTM D3574 (Test D), D395 (Method B); ISO 1856, 3386-1; SAE J1352; PV 3919 SAE J1389 Crocking AATCC 8; ISO 105-A01; SAE J861; Ford FLTM BN 107-01, 02 Density ASTM D3574 (Test A) Dye Transfer Color Bleeding Color Transfer to Water AATCC 107; GMW 14141; Chrysler CLP 463KC-01-01; Ford FLTM AN 101-01 Dust - Out GM 9635P (Inactive September 2013) 2 ; GMW 16998 Environmental Conditioning GMW 3221 (Code A) Environmental Exposure Chrysler CLP 463LB-12-01B; GM 9200P; GMW 14124 (Cycles M, R, W) Fiber Degradation GM 9771P (Inactive July 2015) 2 ; GMW 3387 Flammability ISO 3795; FMVSS 302; SAE J369; Honda C206A, D6003-99; GM 9070P; GMW 3232; TSM 0500G; TL 1010; GB 8410; DBL 5307 (Section 5.1) Fluid Resistance ASTM D896 (A2LA Cert. No. 1976.01) 11/28/2016 Page 2 of 4
Fogging SAE J1756; GMW 3235; Chrysler LP463DB 12-01 Force Deflection ASTM D3574 (Tests B 1 and C) Fungus/Mildew GMW 3259 Hardness Heat Aging Humidity Exposure Moisture Content/Water Absorption/ Thickness Swell ASTM D2240 (Type A); ISO 868 Chrysler CLP 463LB-13-01, MS-AY352, MS-HZ100; Ford WSS-M15P6; GMW 14194, 14196; DBL 5972 (Section 4.3) Chrysler CLP 463 CB-10-01A; GMW 14729 GMW 14777 Odor SAE J1351; Chrysler CLP 463KC-9-01; GMW 3205; VDA270; PV3900 Shrinkage/Dimensional Stability ASTM D2646 (Sections 17 and 18); SAE J315 (Section 15), J883, J855; Ford FLTM BN 105-01, 03; GMW 4217 Stain Resistance GMW 16596 (Section 3.4.2.2), 16597 Stiffness SAE J949; ASTM D790 Tear Strength Tongue Method (Single Leg Rip) Trapezoid Method Trouser Method C Block Method Tensile Strength Grab Method Dumbbell Method ASTM D2261, D3574 (Test F); Chrysler CLP 463 KB-03-01 ASTM D5587; GMW 3326 ISO 13937-2 ASTM D624; ISO 34-1 ASTM D5034, D751 (Section 11, Procedure A) ASTM D412 (Method A), D3574 (Test E) GMW 3010 (A2LA Cert. No. 1976.01) 11/28/2016 Page 3 of 4
Thickness (1 anvil) ISO 5084; SAE J882, J1355; Chrysler CLP 463LB-07-01 Tuft Lock ASTM D1335; Chrysler CLP 463KB-22-01; GM 9127P (Inactive March 2011) 2 ; GMW 14148 Water Spotting AATCC 22; Chrysler CLP 463KC-03-01; GM 9133P (Inactive March 2016) 2 ; GMW 14102 Weight/Mass ASTM D3776; SAE J860; Chrysler CLP 463LB-07-01; Ford FLTM BN 106-01; GMW 3182 Water Wicking SAE J913 1 The laboratory is accredited for the test methods listed above. The accredited test methods are used in determining compliance with the material specifications listed below; however, the inclusion of these material specifications on this Scope does not confer laboratory accreditation to the material specifications. Inclusion of these material specifications on this Scope also does not confer accreditation for every method embedded within the specification. Only the methods listed above on this Scope are accredited. Chrysler: CLP 463LB-12-01B, MS-HZ100, MS-JB2000, MS-JP1-3, MS-JP9-4 Ford: WSS-M15P6, WSS-M15P32, WSS-M15P44, WSS-M8P16, WSS-M99P32 GM: 2715M, 2780M, 6090M GMW: 157571 2 This laboratory s scope contains withdrawn or superseded methods. As a clarifier, this indicates that the applicable method itself has been withdrawn or is now considered historical and not that the laboratory s accreditation for the method has been withdrawn. (A2LA Cert. No. 1976.01) 11/28/2016 Page 4 of 4
Accredited Laboratory A2LA has accredited HP PELZER MATERIALS TESTING LABORATORY Troy, MI for technical competence in the field of Mechanical Testing This laboratory is accredited in accordance with the recognized International Standard ISO/IEC 17025:2005 General requirements for the competence of testing and calibration laboratories. This accreditation demonstrates technical competence for a defined scope and the operation of a laboratory quality management system (refer to joint ISO-ILAC-IAF Communiqué dated 8 January 2009). Presented this 28 th day of November 2016. President and CEO For the Accreditation Council Certificate Number 1976.01 Valid to November 30, 2018 For the tests to which this accreditation applies, please refer to the laboratory s Mechanical Scope of Accreditation.