A New Global Standard

PRESSURE SENSOR DIGITAL PRESSURE SENSOR DP- SERIES Conforming to EMC Directive Recognition Certification [DP-(A)/(A) only] A New Global Standard Dual display for the digital pressure sensors of the future

Dual -color display makes operation easier! The dual display means that the current value and the threshold value can be displayed at the same time to improve ease of operation and visual checking. Introducing a new standard in digital pressure sensor technology. A new global standard Current value and threshold value can be checked at the same time! Dual display allows direct setting of threshold value Equipped with a mm in square compact-sized dual display. Because the current value and the threshold value can be checked at the same time, the threshold value can be set and checked smoothly without having to switch screen modes. ON / OFF operations are still carried out while the threshold values are being set, so setting to the same sensitivity as dial control-type sensors is possible. And naturally a key lock function is also equipped. Threshold value setting method Previous model with single display -9.8 Note current value Operate MODE key Adjust threshold value Return to RUN operation DP- with dual display Man-hours reduced by during RUN operation /4 Simply press a button -color display (Red, Green, Orange) The main display changes color in line with changes in the status of output ON / OFF operation, and it also changes color while setting is in progress. The sensor status can therefore be understood easily, and operating errors can be reduced. Readable digital display! segments are used and an alphanumeric display has been adopted. This improves visual checking of letters and numbers. Main Display OFF: Green (or Red) ON: Red (or Green) SET: Orange During normal operation During setting

Dual Display Direct setting Current value Threshold value Direct setting means Works like a dial control type sensor Main display Comparative Output operation indicator Comparative Output operation indicator Multi-function type: Analog voltage output operation indicator Sub display Mode selection key Increment key Decrement key

Copy function lets work be carried out accurately and quickly Copy function reduces man-hours and human error Sensors can be connected to a master sensor one by one, and a copy of the setting details for the master sensor can be transmitted as data to the other sensors. If making the same settings for multiple sensors, this prevents setting errors from occurring with the other sensors and also reduces the number of changes required to instruction manuals when equipment designs are changed. Setting details can be copied. Copying via copy unit Copying via wiring Master sensor Power supply Slave sensor V V Comparative output Comparative output V V Comparative output Comparative output 56)46 Details transmitted Details received Details copied Advantage Setting man-hours are reduced and sensor setting time is shortened. 4th equipment: 5 minutes approx. Number of pressure sensor: For per equipment and 4 per line rd equipment: 5 minutes approx. nd equipment: 5 minutes approx. 4th equipment: seconds rd equipment: approx. nd equipment: st equipment: The setting details for the master sensor are retained, so continuous copying is possible! For nd and subsequent lines, only the data transmission time is needed. st equipment: 5 minutes approx. Sensor setting time: minutes approx. Master sensor 5 minutes approx. 4th equipment: seconds rd equipment: approx. nd equipment: st equipment: Sensor setting time: 5 minutes seconds approx. Sensor setting time: seconds approx. Previously DP-, st line DP-, nd line Advantage Human operating error is reduced. Because all details are copied automatically, it prevents problems occurring as a result of human error. Instruction manuals can be updated easily when changes occur to equipment design!

Setting is smooth and easy The sensor s setting operation mode has a -level configuration to suit the frequency of use. The setting levels are clearly separated into RUN mode for operation settings that are carried out daily, MENU SETTING mode for basic settings, and PRO mode for special and detailed setting. These make setting operations easy to understand and easy to carry out. RUN mode Settings such as threshold value adjustment and key lock operation can be carried out while the sensor is operating. Simple setting RUN mode Special and detailed setting MENU SETTING mode PRO mode MENU SETTING mode Basic settings such as output mode setting and NO / NC switching can be carried out. PRO mode High-level function settings such as hysteresis adjustment and the copy function can be carried out. Display is orange while setting is in progress The display appears in red and green during RUN operation, but it changes to orange while setting is in progress, so that the sensor status can be viewed at a glance. RUN operation RUN mode While setting MENU SETTING mode PRO mode or Red or green when output is ON / OFF Orange while setting is in progress Default settings that can be used straight away Easy-to-use default settings are provided for applications that are used frequently by pressure sensors. The default settings for low pressure types are ideal for suction checking applications, and those for high pressure types are ideal for checking reference pressure. Buttons with good clicking touch The buttons have a good clicking touch, allowing smooth setting. Low pressure type Comparative output ON OFF kpa Hysterisys digits 5 kpa Ideal for checking suction kpa High pressure type Comparative output MPa.5 MPa Hysterisys digits Ideal for checking reference pressure MPa The clicking feeling is transmitted even through gloves. Reset function If a problem ever occurs with the sensor settings, they can be returned to the default settings. 4

Full range of performance and functions in a compact body All models in the line-up are compound pressure types No sensor settings are required to switch between positive pressure and negative pressure, so that the number of registered part numbers can be decreased. High performance accomplished Low pressure type The low pressure type displays measurements in. kpa at a resolution of /, and has a response time of.5 ms (variable up to 5, ms),.5 % F.S. temperature characteristics and. % F.S. repeatability, giving it high performance. <For low pressure> Ideal for applications such as suction. No misoperations due to vacuum breakdown occur. kpa kpa For low pressure DP- For high pressure kpa <For high pressure> Ideal for applications such as checking reference pressure. Can also be used for simple suction. DP- MPa Resolution: /, Response time:.5 ms Temperature characteristics:.5 % F.S. Repeatability:. % F.S. Displays measurements in. kpa Equipped with independent dual output Standard type Equipped with two independent comparative outputs, and separate sensing modes can be selected for each of them. Since there are two comparative outputs, one of the comparative outputs can even be used for alarm output. In addition, if an output is not being used, it can be disabled. Vacuum breakdown can also be checked during suction applications! ON Comparative output EASY mode OFF ON Comparative output EASY mode OFF kpa Suction checking Vacuum breakdown checking P- kpa P- Reference pressure alarm output is possible during reference pressure checking! Three output modes are suitable for a wide range of applications EASY mode This mode is used for comparative output ON / OFF control. Pressure P ON Comparative output OFF Pressure Hi Lo ON Comparative output OFF H (Hysteresis) H (Hysteresis) H: Fixed Notes: ) Hysteresis can be fixed to one of eight different levels. ) appears in the sub display for comparative output, and appears for comparative output. Hysteresis mode This mode is used for setting comparative output hysteresis to the desired level and for carrying out ON / OFF control. H: digit or more ON Comparative output hysteresis mode OFF ON Comparative output EASY mode OFF kpa Reference pressure checking Alarm output Lo- Hi- P- Note: or appears in the sub display for comparative output, and or appears for comparative output. Window comparator mode This mode is used for setting comparative output ON and OFF at pressures within the setting range. Pressure Hi Lo ON Comparative output OFF H (Hysteresis) H (Hysteresis) H: Fixed Notes: ) Hysteresis can be fixed to one of eight different levels. ) or appears in the sub display for comparative output, and or appears for comparative output. 5

Equipped with auto-reference / remote zero-adjustment functions, More precise pressure management is possible with a minimum of effort If the reference pressure of the device changes, the autoreference function partially shift the comparative output judgment level by the amount that the reference pressure shifts, and the remote zeroadjustment function can reset the display value to zero via external input. These functions are ideal for places where the reference pressure fluctuates wildly, or where fine settings are desired. Multi-function type Without auto-reference and remote zero-adjustment functions Comparative output: Window comparator mode Hi-, Lo-5 4 5 5 Pressure Time Fixed set value Variation in the filling pressure Leak threshold level Trial Trial Trial NG? OK NG? Because the threshold level is fixed for conventional pressure sensors, changes in the reference pressure result in wrong decisions. With auto-reference function applied Comparative output: Window comparator mode Hi-, Lo-5 Sets the absolute threshold level Auto-reference input The display remains at and only the threshold level is changed. With remote zero-adjustment function applied Comparative output: Window comparator mode Hi-, Lo-5 Sets the absolute threshold level Remote zero-adjustment input The display is forced to, and only the filling pressure drop range is displayed. 5 5 Pressure Threshold level before applying auto-reference input Trial 5 Auto-reference input value Time When auto-reference input is applied, the reference pressure is added to the threshold level. If the reference pressure changes to or 4, the auto-reference input compensates for this every time by changing the threshold level, so any variation in the filling pressure can be ignored. OK Threshold level after applying auto-reference input 5 5 Pressure 5 Time 5 OK Threshold level after applying remote zero-adjustment input Threshold level before applying remote zero-adjustment input Trial Displayed when remote zeroadjustment input is applied When remote zero-adjustment input is applied, the reference pressure is forced to. If the reference pressure changes to or 4, the remote zero-adjustment input adjusts the reference pressure to every time the reference pressure changes, so any variation in the filling pressure can be ignored. Peak hold and Bottom hold functions The peak values and bottom values for fluctuating pressures can be displayed using the dual display. Energy-saving design! Equipped with an ECO mode This mode lowers the display luminance to cut power consumption by approximately %. The displays can also be turned off completely to achieve a power saving of approximately 4 %. Normal ECO-STD Power consumption Approx. % less Power consumption Approx. ECO-FULL 4 % less Blinks alternately Current consumption for 4 V power supply: 5 ma or less Current consumption for 4 V power supply: 5 ma or less Current consumption for 4 V power supply: ma or less 6

Other useful functions Sub display can be customized The sub display can be set to indicate any other desired values or letters apart from the threshold value. This eliminates the need for tasks such as affixing a label to the device to indicate the normal pressure value. Setting details can be understood at a glance The DP- setting details appear in the digital display. Because the settings are in numeric form that can be easily understood, it is useful for times such as when receiving technical support by telephone. What are the check codes for the setting? The code on the main display is 5. The sub display reads 7. nd digit: Setting status for comparative output st digit: Setting status for comparative output rd digit: Threshold value setting 4th digit: Display color setting Indicates desired values and letters <Unit display> <Number display> <Desired letter display> 5th digit: Response time setting 6th digit: Display unit setting 8th digit: ECO mode setting 7th digit: Display refresh rate setting Cable can be connected with one-touch connection The accessory connector attached cable ( m 6.56 ft) can be connected easily with one-touch connection. Types without connector attached DP--J cable are also available Commercially-available connectors can be used for cable connections. Only the required length of cable needs to be used, which contributes to a reduced amount of wastage for unneeded cable. Connection cable * Environmentally friendly Commercially-available parts can be used! * Options: m.8 ft / m 9.84 ft / 5 m 6.44 ft types are also available. M8 piug-in connector types are also available. (Only for Europe) DP--E-P-J Mating cable CN-4A-C (cable length m 6.56 ft) CN-4A-C5 (cable length 5 m 6.44 ft) M8 connector G /8 male thread 7

Installation is also easy! Tight installation to panels is possible An exclusive mounting bracket that is suitable for to 6 mm.9 to.6 in panel thickness is available. Tight installation is possible Takes up much less space Front protection cover available MS-DP- A single mounting hole! An exclusive mounting bracket (MS-DP-) that supports tight installation is available Space savings can also be obtained if an L-shaped mounting bracket is used. MS-DP- MS-DP-5 Tight installation is possible Ceiling mounting Floor mounting Rear mounting Positioning bosses for easier mounting bracket installation Short pressure port type is lightweight and takes up little space Space saving! Compact size with a depth of only mm in, so that it can easily fit into narrow spaces. Standard type R 8 male thread Elbow joint Light weight of g! * g lighter than standard types. This reduces the loads on movable parts such as robot arms. Short pressure port type DP--M Short pressure port type * Excluding cables with connector attached Shortened to.5 mm.49 in! Light weight g approx. Ideal for clean environments! Stainless steel (SUS) which does not rust or generate gas is used as the port material. mm [Material: Stainless steel (SUS)] in * The illustration shows connection using an elbow joint. The elbow joint is sold separately. 8

Switch-over of the pressure port or flat mounting on the wall is possible For short pressure port type By mounting the flat attachment to DP--M(-P), pressure port and cable can now be pulled out in downward, left or right directions. Flat mounting on surfaces such as the wall is made possible. Previous model DP / DP series can be switched over to DP- series. Previous model Rc /8 conversion bushing improves compatibility with the previous model For short pressure port type By equipping the push-in converter with DP--M(-P), pressure port can be converted from to Rc /8 female thread. Bore diameter conversion to the DP / DP series is possible. Rc /8 female thread Flat attachment MS-DP-F mm.787 in pitch mm.787 in pitch Model No. MS-DP-FM MS-DP-FR MS-DP-FN MS-DP-FE Pressure port Rc /8 female thread NPT /8 female thread G /8 female thread Conversion bushing MS-DP-7 possible directions to mount ORDER GUIDE Type Appearance Rated pressure range Model No. Pressure port Comparative output Standard pressure port type Short pressure port type Europe Asia North America Asia M8 plug-in connector type Standard Multi-function Standard Multi-function Standard Multi-function Standard Multi-function Standard Multi-function For low pressure For high pressure For low pressure For high pressure For low pressure For high pressure For low pressure For high pressure For low pressure For high pressure For low pressure For high pressure For low pressure For high pressure For low pressure For high pressure For low pressure For high pressure For low pressure For high pressure * CN-4A-C Connector attached ( cable m 6.56 ft ) is attached. Excluding M8 plug-in ( connector type ). to. kpa. to. MPa. to. kpa. to. MPa. to. kpa. to. MPa. to. kpa. to. MPa. to. kpa. to. MPa. to. kpa. to. MPa. to. kpa. to. MPa. to. kpa. to. MPa. to. kpa. to. MPa. to. kpa. to. MPa DP- DP- DP-A DP-A DP--E-P DP--E-P DP-A-E-P DP-A-E-P DP--E-P-J DP--E-P-J DP-A-E-P-J DP-A-E-P-J DP--N DP--N-P DP--N DP--N-P DP-A-N DP-A-N-P DP-A-N DP-A-N-P DP--M DP--M-P DP--M DP--M-P DP-A-M DP-A-M-P DP-A-M DP-A-M-P R /8 male thread G /8 male thread G /8 male thread NPT /8 male thread NPN open-collector transistor NPN open-collector transistor NPN open-collector transistor NPN open-collector transistor NPN open-collector transistor NPN open-collector transistor NPN open-collector transistor NPN open-collector transistor NPN open-collector transistor Type without connector attached cable Type without connector attached cable CN-4A-C is available. When ordering this type, suffix -J to the Model No. (e.g.) Type without connector atlached cable of DP--N is DP--N-J Accessory CN-4A-C (Connector attached cable m 6.56 ft) 9

OUT -ADJ OUT MODE OPTIONS Designation Connector attached cable Connector attached cable (Flexible cable) M8 connector attached cable Connector Sensor mounting bracket Panel mounting bracket Front protection cover Conversion bushing Flat attachment Copy unit Note: The connector attached cable CN-4A-C is supplied with the DP- series. (Excluding M8 plug-in connector type). Panel mounting bracket, Front protection cover MS-DP- MS-DP-4 MS-DP- Front protection cover DPX-4 (optional) can be installed on MS-DP-4. Front protection cover MS-DP- Flat attachment MS-DP-FM Model No. CN-4A-C CN-4A-C(Note) CN-4A-C CN-4A-C5 CN-4A-R-C CN-4A-R-C CN-4A-R-C CN-4A-R-C5 CN-4A-C CN-4A-C5 CN-4A MS-DP- MS-DP-5 MS-DP- MS-DP-4 MS-DP- MS-DP-7 MS-DP-FM MS-DP-FR MS-DP-FN MS-DP-FE SC-SU Panel mounting bracket MS-DP- MS-DP-FR MS-DP-FN MS-DP-FE Length: m.8 ft Length: m 6.56 ft Length: m 9.84 ft Length: 5m 6.44 ft Length: m.8 ft Length: m 6.56 ft Length: m 9.84 ft Length: 5m 6.44 ft Length: m 6.56 ft Length: 5m 6.44 ft Description. mm 4-core cabtyre cable with connector on one end Cable outer diameter: ".7 mm ".46 in. mm 4-core flexible cabtyre cable with connector on one end Cable outer diameter: ".7 mm ".46 in For M8 plug-in connector type The connector on one end Cable outer diameter: "4 mm ".57 in Set of housings and 4 contacts Allows sensors to be installed on the flooring or ceiling. Multiple sensors can also be mounted closely. Allows sensors to be installed on the wall. Multiple sensors can also be mounted closely. Allows installation to panels with thickness of to 6 mm.9 to.6 in. Multiple sensors can also be mounted closely. Allows replacement from DP / DP series to DP- series. For newly designed set-up, please use panel mounting bracket MS-DP- for panel mounting. Protects the adjustment surfaces of sensors. (Can be attached when using the panel mounting bracket) By equipping with DP--M(-P), pressure port can be converted to Rc /8 female thread. Replacement from DP / DP series is possible. Pressure port and cable can now be Rc /8 female thread pulled out in downward, left or right NPT /8 female thread directions. Flat mounting on surfaces such as the wall is made possible. G /8 female thread Copy the controller settings to other controllers. DP- DP / DP DP- ñ.kpa Remove Connector attached cable CN-4A-C CN-4A-R-C M8 connector attached cable CN-4A-C.4.6 "4 ".57 "9 ".54 (Unit: mm in) Sensor mounting bracket MS-DP- Sensor mounting bracket MS-DP- Remove MS-DP-5 Insert Mounting holes for DP / DP series can be used as is. Panel mounting bracket MS-DP-4 Sensor mounting bracket MS-DP-5 M (length 6 mm.6 in) screws with washers Accessory for ( MS-DP- ) M (length 6 mm.6 in) screws with washers ( ) Accessory for MS-DP-5 Recommended connector Contact: SPHD-T-P.5, Housing: PAP-4V-S (Manufactured by J.S.T. Mfg.Co., Ltd.) Note: Contact the manufacturer for details of the recommended products. Recommended crinping tool Model No.: YC-6R (Manufactured by J.S.T. Mfg. Co., Ltd.) Note: Contact the manufacturer for details of the recommended products. Net weight: MS-DP-FM 5g approx. MS-DP-FR/FN/FE 5g approx. Two M (length 8 mm.5 in) screws, two M4 (length mm.787 in) screws are attached. Copy unit SC-SU Conversion bushing MS-DP-7 M5 female thread Rc /8 female thread Conversion bushing MS-DP-7

DP- SPECIFICATIONS Asia (Note ) Europe M8 plug-in connector type Item North America (Note ) Type of pressure Rated pressure range Set pressure range Pressure withstandability Applicable fluid Selectable unit Supply voltage Power consumption Comparative output Environmental resistance Model No. Output operation / Output modes Hysteresis Repeatability Response time Short-circuit protection External input (Note ) Auto-reference function / Remote zero-adjustment function Type Analog voltage output (Note ) Display Indicator Displayable pressure range Protection Ambient temperature Ambient humidity Voltage withstandability Insulation resistance Vibration resistance Shock resistance Temperature characteristics Pressure port Material Connecting method / Cable length Weight Standard Multi-function For low pressure For high pressure For low pressure For high pressure DP-(-M)(-P) DP-(-M)(-P) DP-A(-M)(-P) DP-A(-M)(-P) DP--E-P DP--E-P DP-A-E-P DP-A-E-P DP--E-P-J DP--E-P-J DP-A-E-P-J DP-A-E-P-J DP--N(-P) DP--N(-P) DP-A-N(-P) DP-A-N(-P) Gauge pressure. to. kpa. to. MPa. to. kpa. to. MPa. to. kpa. to. MPa. to. kpa. to. MPa. to. kgf/cm to, kpa. to. kgf/cm to, kpa. to. bar 4.5 to 4.5 psi. to. kgf/cm. to. bar 4.5 to 4.5 psi. to. kgf/cm 75 to 75 mmhg. to. bar 75 to 75 mmhg. to. bar 9.5 to 9.5 inhg 4.6 to 45. psi 9.5 to 9.5 inhg 4.6 to 45. psi 5 kpa.5 MPa 5 kpa.5 MPa Non-corrosive gas For low pressure: kpa, kgf/cm, bar, psi, mmhg, inhg, For high pressure: MPa, kpa, kgf/cm, bar, psi to 4 V DC % Ripple P-P % or less Normal operation: 84 mw or less (Current consumption 5 ma or less at 4 V supply voltage) ECO mode: 6 mw or less at STD (Current consumption 5 ma or less at 4 V supply voltage) 48 mw or less at FULL (Current consumption ma or less at 4 V supply voltage) <Asia (NPN output), North America (NPN output)> NPN open-collector transistor Maximum sink current: ma Applied voltage: V DC or less (between comparative output and V) Residual voltage: V or less (at ma sink current) <Asia (PNP output), Europe, North America (PNP output)> Maximum source current: ma Applied voltage: V DC or less (between comparative output and V) Residual voltage: V or less (at ma source current) NO / NC (selectable by key operation) / EASY mode / Hysteresis mode / Window comparator mode Minimum digit (variable) (however, digits when using psi unit). % F.S. (within digits). % F.S. (within digits). % F.S. (within digits). % F.S. (within digits).5 ms, 5 ms, ms, 5 ms, 5 ms, ms, 5 ms, 5 ms,, ms, 5, ms, selectable by key operation Incorporated <Asia (NPN output), North America (NPN output)> <Asia (PNP output), Europe, North America (PNP output)> ON voltage:.4 V DC or less ON voltage: 5 V to V DC OFF voltage: 5 to V DC, or open OFF voltage:.6 V DC or less, or open Input impedance: kω approx. Input impedance: kω approx. Input time: ms or more Input time: ms or more Output voltage: to 5 V DC Output voltage:.6 to 5 V Zero point: within V 5 % F.S. Zero point: within V5 % F.S. Span: within 4 V 5 % F.S. Span: within 4.4 V5 % F.S. Linearity: within % F.S. Linearity: within % F.S. Output impedance: kω approx. Output impedance: kω approx. 4 digits 4 digits -color LCD display (Display refresh rate: 5 ms, 5 ms,, ms, selectable by key operation). to. kpa. to. MPa. to. kpa. to. MPa. to. kgf/cm to, kpa. to. kgf/cm to, kpa. to. bar 4.5 to 4.5 psi. to. kgf/cm. to. bar 4.5 to 4.5 psi. to. kgf/cm 75 to 75 mmhg. to. bar 75 to 75 mmhg. to. bar 9.5 to 9.5 inhg 4.6 to 45. psi 9.5 to 9.5 inhg 4.6 to 45. psi Orange LED Orange LED Comparative output operation indicator, comparative output operation indicator: Comparative output operation indicator: Lights up when comparative output is ON, ( Lights up when each comparative output is ON ) ( Analog voltage output operation indicator: Lights up when setting ) IP4 (IEC) to 5 C 4 to F, Storage: to 6 C 4 to 4 F 5 to 85 % RH (No dew condensation or icing allowed), Storage: 5 to 85 % RH, V AC for one min. between all supply terminals connected together and enclosure 5 MΩ, or more, with 5 V DC megger between all supply terminals connected together and enclosure to 5 Hz frequency, mm.8 in amplitude, in X, Y and Z directions for two hours each (when panel is mounted: to 5 Hz frequency,.75 mm. in amplitude, in X, Y and Z directions for two hours each) Within.5 % F.S. (at C 68 F) m/s acceleration ( G approx.) in X, Y and Z directions for three times each Within % F.S. (at C 68 F) Within.5 % F.S. (at C 68 F) Asia: R (PT) /8 male thread [excluding DP--M(-P)], Europe: G /8 male thread, North America: NPT /8 male thread Enclosure: PBT (glass fiber reinforced), LCD display: Acrylic, Pressure port: Brass (nickel plated)[dp--m(-p), DP--J: Stainless steel (SUS)], Mounting threaded part: Brass (nickel plated), Switch part: Silicone rubber Connector / Total length up to m 8.84 ft (less than m.88 ft when conforming to CE marking) is possible with. mm, or more, cable Net weight: 4 g approx., Gross weight: 5 g approx. (DP--M(-P):5 g approx.) Within % F.S. (at C 68 F) Accessories CN-4A-C (Connector attached cable m 6.56 ft): pc. (excluding M8 plug-in connector type) Notes: ) Where measurement conditions have not been specified precisely, the conditions used were an ambient temperature of C 68 F. ) Model Nos. of Asia type having -M are short pressure port type. Model Nos. of Asia and North America types having the suffix -P are PNP output type. ) Cannot be used at the same time.

DP- SPECIFICATIONS Item Designation Model No. Copy unit SC-SU Applicable sensor Digital pressure sensor DP- series, DPC- series, Digital fiber sensor FX- series Supply voltage (Note ) Repeatability of connecting and disconnecting (Note ) Ambient temperature Ambient humidity Material Weight V DC [AC adapter (accessory): Input to 4 V AC 5 / 6 Hz)] 5, times approx. to 4 C to 4 F (No dew condensation allowed), Storage: to 6 C 4 to 4 F 5 to 85 % RH, Storage: 5 to 85 % RH Enclosure base: ABS, Top cover: ABS, Rubber foot: Natural rubber Net weight: 9 g approx., Gross weight: 5 g approx. Notes: ) For destinations where the shape of the AC adapter plug differs from the shape for Japan, please prepare a separate conversion adapter. ) Number of repeatability may vary depending on the usage conditions. I/O CIRCUIT AND WIRING DIAGRAMS I/O circuit diagram Standard type Sensor circuit Tr DP- Tr D ZD Internal circuit NPN output type Terminal No. Color code of connector attached cable (Brown) V (Black) Load Comparative output Load ma max. ZD (White) Comparative output ma max. 4 (Blue) V Users circuit Symbols D : Reverse supply polarity protection diode ZD, ZD : Surge absorption zener diode Tr, Tr : NPN output transistor to 4 V DC % Multi-function type Sensor circuit 5 V Tr Tr kω D D ZD Internal circuit 4 Terminal No. Color code of connector attached cable (Brown) V (White) Analog voltage output or External input Load (Black) Comparative output (Blue) V Users circuit ma max. Symbols D, D : Reverse supply polarity protection diode ZD : Surge absorption zener diode Tr : PNP input transistor Tr : NPN output transistor to 4 V DC % Terminal arrangement diagram 4 Terminal Designation V Comparative output Standard type: Comparative output Multi-function type: Analog voltage output or External input 4 V I/O circuit diagram Standard type Sensor circuit DP--P PNP output type Terminal No. Color code of connector attached cable (Brown) V D ZD ma max. Tr (Black) Comparative output ZD ma max. Load Tr (White) Comparative output Load (Blue) V 4 Internal circuit Users circuit Symbols D : Reverse supply polarity protection diode ZD, ZD : Surge absorption zener diode Tr, Tr : PNP output transistor to 4 V DC % Multi-function type Sensor circuit Tr Tr kω D Internal circuit (Brown) V D ZD ma max. (Black) Comparative output 4 Terminal No. Color code of connector attached cable (White) Analog voltage output or External input (Blue) V Users circuit Load Symbols D, D : Reverse supply polarity protection diode ZD: Surge absorption zener diode Tr : PNP output transistor Tr : NPN input transistor to 4 V DC % Terminal arrangement diagram 4 Terminal Designation V Comparative output Standard type: Comparative output Multi-function type: Analog voltage output or External input 4 V

DP- I/O CIRCUIT AND WIRING DIAGRAMS DP--E-P-J PNP output type I/O circuit diagram Standard type Sensor circuit Tr Tr ZD D 4 ZD Terminal No. Color code of connection cable (Brown) V ma max. (Black) Comparative output ma max. Load (White) Comparative output Load (Blue) V to 4 V DC % Multi-function type Sensor circuit Tr Tr kω D Internal circuit Terminal No. Color code of connection cable (Brown) V D ZD ma max. 4 (Black) Comparative output (White) Analog voltage output Load or External input (Blue) V Users circuit to 4 V DC % Internal circuit Users circuit Symbols D : Reverse supply polarity protection diode ZD, ZD : Surge absorption zener diode Tr, Tr : PNP output transistor Symbols D, D : Reverse supply polarity protection diode ZD: Surge absorption zener diode Tr : PNP output transistor Tr : NPN input transistor Terminal arrangement diagram 4 Terminal Designation V Standard type: Comparative output Multi-function type: Analog voltage output or External input V 4 Comparative output PRECAUTIONS FOR PROPER USE Never use this product as a sensing device for personnel protection. In case of using sensing devices for personnel protection, use products which meet laws and standards, such as OSHA, ANSI or IEC etc., for personnel protection applicable in each region or country. The DP- series is designed for use with non-corrosive gas. It cannot be used with liquid or corrosive gas. Wiring Make sure that the power supply is off while wiring. Verify that the supply voltage variation is within the rating. If power is supplied from a commercial switching regulator, ensure that the frame ground (F.G.) terminal of the power supply is connected to an actual ground. In case noise generating equipment (switching regulator, inverter motor, etc.) is used in the vicinity of this sensor, connect the frame ground (F.G.) terminal of the equipment to an actual ground. Do not run the wires together with high-voltage lines or power lines or put them in the same raceway. This can cause malfunction due to induction. Incorrect wiring will cause problems with operation. Connection Connector attached cable Do not apply stress directly to the [CN-4A(-R)-C] connection cable leader or to the connector. Mounting MS-DP- / MS-DP-5 sensor mounting brackets are available separately, and it should be used for mounting. When tightening the sensor to the sensor mounting bracket, use a tightening torque of.5 Nm or less. Sensor mounting bracket MS-DP- (Optional) M (length 6 mm.6 in) screws with washers Accessory for MS-DP- ( and MS-DP-5 ) The MS-DP- panel mounting bracket (optional) and the MS-DP- front protection cover (optional) are also available. Front protection cover MS-DP- (optional) Conditions in use for CE conformity The DP- series is a CE conformity product complying with EMC Directive. The harmonized standard with regard to immunity that applies to this product is EN 6-6- and the following condition must be met to conform to that standard. Panel mounting bracket MS-DP- (optional) Condition The sensor should be connected less than m.88 ft from the power supply. The signal line to connect with this sensor should be less than m 98.45 ft.

OUT -ADJ OUT MODE PRECAUTIONS FOR PROPER USE Mounting The MS-DP-4 panel mounting bracket is available when switching from the DP/ DP series. Front protective cover DPX-4 (Optional) can be installed on MS-DP-4. DP- DP / DP An conversion bushing is available for when using the DP--M short pressure port type. It can be used to switch between this model and the DP / DP series. When connecting to the pressure port, use a tightening torque of. Nm or less. Rc 8 female thread DP- ñ.kpa Remove Insert Panel mounting bracket MS-DP-4 Remove Mounting holes for DP / DP series can be used as is. Piping If connecting a commercially-available coupling to the pressure port, attach a mm.47 in spanner (4 mm.55 in spanner for DP--E type) to the hexagonal section of the pressure port to secure it, and tighten at a torque of 9.8 Nm or less. If it is tightened using excessive torque, it may damage the coupling or the pressure port. In addition, wrap sealing tape around the coupling when connecting it to prevent leaks. 4 mm.55 in spanner mm.47 in spanner If connecting a commercially-available joint to the pressure port of the DP--M, hold the main unit in your hand to steady it, and tighten to a torque of. N m or less. If it is tightened to an excessive torque, the joint or the main unit may become damaged. If connecting a commercially-available joint to the pressure port of the MS-DP-7, tighten to a torque of 9.8 N m or less. Conversion bushing MS-DP-7 The MS-DP-F flat attachment is available. If using the MS-DP-F flat attachment (optional), install by following the procedures given below. Decide the direction of this product to mount with the sensor. The tightening torque should be N m or less when connecting a coupling to the pressure port of MS-DP-FM. Pressure port Coupling (Please arrange separately) Pressure port faces downward Pressure port faces leftward Note: It is not possible to mount this product such that the pressure port faces upward. Pressure port faces rightward When connecting the coupling to the pressure port of MS-DP-FR/FE/FN, hold the pressure port with a 4 mm.55 in spanner and make sure that the tightening torque is 9.8 Nm or less. In addition, in order to prevent any leakage, wind a sealing tape on the coupling when connecting. Pressure port faces upward Mount this product with the M female threads of the sensor by using the attached M (length 8 mm.5 in) screws. The tightening torque should be.5 Nm or less. M female thread M (length 8 mm.5 in) screw (Accessory) 4 mm.55 in spanner M female thread Note: Do not tighten the pressure port by holding the product with the spanner. It may cause the product breakage. Mount this product with the mounting surface by using the attached M4 (length mm.787 in) screws. The tightening torque should be. Nm or less. Groove Connector attached cable M4 (length mm.787 in) screw (Accessory) Note: Take care that if the cable with connector is sticking out of the side groove of this product when mounting, the cable may disconnected. Flat attachment Make sure to mount MS-DP-F with the sensor properly. If it is not mounted properly, air leakage may occur. Take care that the excessive mounting and dismounting of this product may cause deterioration of the O-ring. If you touch the O-ring of MS-DP-F, or any scratch or dust, etc. is attached to it, air leakage may occur and the sensing performance may deteriorate. Take sufficient care when using and storing MS-DP-F. 4

DP- PRECAUTIONS FOR PROPER USE Others This product has been developed / produced for industrial use. Use within the rated pressure range. Do not apply pressure exceeding the pressure withstandability value. The diaphragm will get damaged and correct operation shall not be maintained. Do not use during the initial transient time (.5 sec. approx.) after the power supply is switched on. Avoid dust, dirt, and steam. Take care that the sensor does not come in direct contact with water, oil, grease, or organic solvents, such as, thinner, etc. Do not insert wires, etc., into the pressure port. The diaphragm will get damaged and correct operation shall not be maintained. Do not operate the keys with pointed or sharp objects. RUN mode This is the normal operating mode. Setting item Threshold value setting Zero-adjustment function Key lock function Peak hold / bottom hold function MENU SETTING mode If the mode selection key is pressed and held for seconds in RUN mode, the mode will switch to MENU SETTING mode. If the mode selection key is pressed while a setting is being made, the mode will switch to RUN mode. In this case, the settings that have been changed will be entered. Setting item Comparative output output mode setting Comparative output output mode setting (standard type only) Analog voltage output / external input switching (multi-function type only) NO / NC switching Response time setting Description The threshold values for ON / OFF operation can be changed directly by pressing the increment key (UP) and the decrement key (DOWN). This forces the pressure value display to be reset to zero when the pressure port is open on the atmospheric pressure side. Stops key operations from being accepted. Displays the peak value and bottom value for fluctuating pressure. The peak value appears in the main display, and the bottom value appears in the sub display. Description Sets the output mode for comparative output. Sets the output mode for comparative output. Allows switching between analog voltage output and auto-reference input / remote zero-adjustment input. Sets normally open (NO) or normally closed (NC). Sets the response time. The response time can be selected from.5 ms, 5 ms, ms, 5 ms, 5 ms, ms, 5 ms, 5 ms,, ms and 5, ms. PRO mode If the mode selection key is pressed and held for 5 seconds in RUN mode, the mode will switch to PRO mode. If the mode selection key is pressed while a setting is being made, the mode will switch to RUN mode. In this case, the settings that have been changed will be entered. Setting item Sub display switching Display refresh rate switching Hysteresis fix value switching Linked display color switching (standard type only) ECO mode setting Setting check code Setting copy mode Reset setting Table of codes Code Comparative output NO / NC output mode switching EASY Hysteresis st digit Window comparator NO NC Description Changes the information in the sub display during RUN mode operation to the desired alphanumeric display. Changes the display refresh rate for the pressure value displayed in the main display. OFF OFF P-, Lo- Auto- NC NO reference Hi- EASY Remote NO NC P-, Lo- zero-adjustment NC NO Hi- NO NC Sets the hysteresis for EASY mode and window comparator mode. (8 steps) Allows the display color for the main display to be switched in line with the output operation for comparative output or comparative output. Allows power consumption to be reduced by dimming the display or turning it off. Allows the setting details to be checked via codes. Allows the setting details for the master sensor to be copied to slave sensors. Resets the settings to the factory settings. nd digit Multi-function rd digit Standard type Comparative output NO / NC output mode switching Hysteresis Window comparator NC NO type Analog voltage output / External input Analog voltage output Threshold value display ADJ. Display color for main display Red when ON Green when ON Always red Always green 4th digit Standard type only Display color linking Comparative output Comparative output Comparative output Comparative output Comparative output Comparative output Comparative output Comparative output Display color switching for main display Allows the color for the main display to be changed. The colors can be set to red / green or green / red to correspond to ON / OFF output, or it can be fixed at red or green all the time. Unit switching (high pressure type only) Pressure unit can be changed. Code 5th digit 6th digit 7th digit 8th digit Response time Unit switching Display reflesh rate ECO mode.5 ms MPa 5 ms OFF 5 ms kpa 5 ms STD ms kgf/cm, ms FULL 5 ms bar 5 ms psi ms mmhg 5 ms inchhg 5 ms, ms 5, ms 5

DP- DIMENSIONS (Unit: mm in) The CAD data in the dimensions can be downloaded from the SUNX website: http://www.sunx.com DP- Sensor 4.5.67 5.5 7.5 9.5.4.95.74.787 Connector.787.47.5.59 R (PT) /8 male thread (North America: NPT /8) M female thread, 4.57 deep Europe.94.76 7 Europe 4.55 G /8 male thread DP--M(-P) Sensor 5.5.4 4.5.77.787 "8. ".7.787 connector.5.59 M female thread, 4.57 deep, 4.57 deep DP--E-P-J Sensor 5.5.4 47.5.87 7.76.787 M8 connector 9.5.74 4.5.77.787 4.55 G /8 male thread.5.59 5.59 7.76 M female thread, 4.57 deep 6

DIMENSIONS (Unit: mm in) The CAD data in the dimensions can be downloaded from the SUNX website: http://www.sunx.com MS-DP- 4.5.57 Sensor mounting bracket (Optional) 9.5.74.787 t t.79.787 4..65 R R.5.866.787.5 ". ".9.9 -R. R.8 -".5 ".8 ( ) 5..9 5.5.7 44.7 Material: Cold rolled carbon steel (SPCC) (Uni-chrome plated) Two M (length 6 mm.6 in) screws with washers are attached. Assembly dimensions Mounting drawing with DP- 45.77.866 -R. R.8 9.5.74 4..65 5.59 4.5.57 5.5.4 45.77 7.5.95 4.5.67.5.59 9.5.74 t t.79.47 MS-DP-5.75.896 Sensor mounting bracket (Optional) Assembly dimensions Mounting drawing with DP--M R6.75 R.66 4.5.77.787 9.5.6.787.5.5.787 "4.5 ".77 8.5.5 44.5.75 -".5 ".8 8. t.5 t.59 Material: Cold rolled carbon steel (SPCC) (Uni-chrome plated) Two M (length 6 mm.6 in) screws with washers are attached. 6.6 49.5 ( ).949 "4.5 ".77.787 9.5.6 49.5.787 8.5.949. 4.5.77 4.5.77.5.59 8. 5.5.6 "8. ".7 t.5 t.59 MS-DP- MS-DP- Assembly dimensions Mounting drawing with DP- Panel mounting bracket (Optional), Front protection cover (Optional) Panel cut-out dimensions When unit is installed.4..6 ( ) 4.5.58.787 ( ) 9..547 4.5.58 5.969.4.5 7..8.4 Front protection cover 8.7.4 8..7 7.5.95 9.5.74.47 R(PT) /8 male thread Panel thickness dimension to 6 mm.9 to.6 in When n units are installed horizontally in series 55.65 or more. n.5.8 (n-).4..6.4..6 When n units are installed vertically in series.4..6. n.5.8 (n-).4.5 Connector, 4.57 deep M female thread, (5.47 max) 4.57 deep View A Material: POM (Panel mounting bracket) Polycarbonate (Front protection cover) Note: The panel thickness should be to 6 mm.9 to.6 in. 55.65 or more Note: The panel thickness should be to 6 mm.9 to.6 in. 7

DIMENSIONS (Unit: mm in) The CAD data in the dimensions can be downloaded from the SUNX website: http://www.sunx.com MS-DP-4 Assembly dimensions Mounting drawing with DP- 4.575 Panel mounting bracket (Optional) ( ) 4.7.68 4.575 9.7 (.8) 4.7.68 6.47 6.5.4 6.5.56.8 R /8 male thread.47 Panel mounting bracket body Connector M5 female thread Spacer Panel cut-out dimensions 8.5 56.5 6.47.5. 6.47.5. Front protection cover (DPX-4) 8.5 Panel thickness dimension to. mm.9 to.6 in Panel mounting bracket Note: The panel tickness should be to mm.9 to.6 in. Material: Panel mounting bracket body Nylon 6 Panel mounting bracket Stainless steel (SUS4) Spacer Cold rolled carbon steel (SPCC)(Uni-chrome plated) MS-DP-7 Conversion bushing (Optional) 5.8.6.5.8.5 (. ) 7.8.7 4.55 M5 male thread Gasket.4.94 8.5 Rc /8 female thread Material: Brass (Nickel plated) Weight: g approx. MS-DP-FM Assembly dimensions Mounting drawing with DP--M 44.5.75 -"4. ".69 ( ) ( ) 44.5.75 4.945.787 4.945 Flat attachment (Optional) 4.945 6.5.56 5.5.7 7.457.5.45 7.5.689.4 Material: EnclosurePolybutylene terephthalate (PBT) (Glass fiber reinforced) Pressure portstainless steel (SUS) 8.5.5 O-ringHydrogenated Nitrile Butadiene Rubber (H-NBR) Weight: 5 g approx. (flat attachment only) Two M (length 8 mm.5 in) screws, two M4 (length mm.787 in) screws are attached. MS-DP-FR/FN/FE Assembly dimensions Mounting drawing with DP--M 5.5.67 -"4. ".69 Pressure port G /8 female thread (Note) 4.55.787 4.945 ( ) 5.5.67 4 (.945) Note: MS-DP-FR has a Rc/8 female thread. MS-DP-FN has a NPT/8 female thread. Flat attachment (Optional) 4.945 6.5.56 5.5.7.5.5 Product distinguishing mark MS-DP-FR: line MS-DP-FN: line MS-DP-FE: line 7.457.5.45 7.5.689.4 8.5.5 Material: EnclosurePolybutylene terephthalate (PBT) (Glass fiber reinforced) Pressure portstainless steel (SUS) O-ringHydrogenated Nitrile Butadiene Rubber (H-NBR) Weight: 5 g approx. (flat attachment only) Two M (length 8 mm.5 in) screws, two M4 (length mm.787 in) screws are attached. 8

DIMENSIONS (Unit: mm in) The CAD data in the dimensions can be downloaded from the SUNX website: http://www.sunx.com CN-4A(-R)-C Connector attached cable (Optional, CN-4A-C is attached to the sensor) 5 5 (.78) (.969) 8 (.5) 8 ( ) L ".7 ".46 cable.5 Model No. CN-4A(-R)-C CN-4A(-R)-C CN-4A(-R)-C CN-4A(-R)-C5 Cable length L (mm in), 9.7, 78.74, 8. 5, 96.85 SC-SU Copy unit (Optional) V DC entry DC IN V 4 5.5.787.79 45.77.5.8 Power indicator (Green) 9.54 MASTER SLAVE MASTER SLAVE POWER ENTER SC-SU MADE IN JAPAN ENTER key.9 ".8 ".54 All information is subject to change without prior notice. SUNX Limited 4- Ushiyama-cho, Kasugai-shi, Aichi, 486-9, Japan Phone: +8-568--7 FAX: +8-568--6 http://www.sunx.com Overseas Sales Dept. Phone: +8-568--786 FAX: +8-568--859 Printed on % recycled paper PRINTED IN JAPAN No.CE-DP--7 April, 8