INSTRUCTION MANUAL (A037) Requires: 50cc gasoline engine, -channel radio w/ 6 high torque servos. Specifications Wing Span Wing Area Flying Weight Fuselage Length 118 in / 3000 mm 1990 sq in / 18 sq dm 18.5 lbs / 850 g 75 in / 1900 mm * Specifications are subject to change without notice. * Warning! This model is not a toy. It is designed for maximum performance. Please seek advice if one is not familiar with this kind of engine powered precision model. Operating this model without prior preparation may cause injuries. Remember, safety is the most important thing. Always keep this instruction manual at hand for quick reference. The World Models Manufacturing Co., LTD. www.theworldmodels.com FACTORY PRE-FABRICATED ALMOST-READY-TO-FLY (ARF) SERIES MADE IN CHINA A037PO798A109
BEFORE YOU BEGIN PARTS LIST ASSEMBLY SAFETY PRECAUTIONS INDEX P.1 P. P.3-P.13 P.13 BEFORE YOU BEGIN 1 3 Read through the manual before you begin, so you will have an overall idea of what to do. Check all parts. If you find any defective or missing parts contact your local dealer. Please DRY FIT and check for defects for all parts that will require CA or Epoxy for final assembly. Any parts you find to be defective after the gluing process may be difficult to remove for warranty replacement. The manufacturer will replace any defective parts, but will not extend to the parts that are good before gluing to defective parts during assembly. Warranty will not cover any parts modified by customer. Symbols used throughout this instruction manual comprise of the following :- Apply epoxy glue. Apply instant glue (C.A.glue, super glue.) Apply thread locker Must be purchased separately! Assemble left and right sides the same way. Ensure smooth non-binding movement while assembling. Peel off shaded portion covering film. Cut off shaded portion. 3mm Drill holes with the specified diameter (here: 3mm). Pierce the shaded portion covering film. Pay close attention here! Warning! Do not overlook this symbol! A037PO798A109 P.1
Parts List 1. MAIN WING -- 1 pair. SERVO MOUNTING PANEL (For Aileron) PL5310010 -- 1 pair HEAVY DUTY CLEVIS PL1100 -- sets SOCKET HEAD SCREW Mx60mm -- pcs SCREW PWA.3x8mm -- 8 pcs M NYLON INSERT LOCK NUT -- pcs HEAVY DUTY HORN BRACKET PL1100 -- sets HEAVY DUTY SERVO HORN PL1050 -- sets PUSHROD M3xD5x113mm w/ Threads (For Aileron) -- pcs SWIVEL CLEVIS HORN FAIRING PL610010 -- sets 3. SOCKET HEAD SCREW M3x18mm -- 8 pcs SOCKET HEAD SCREW Mx18mm -- pcs WIRE BRACKET PL5330030Y -- 8 pcs MAIN WING STRUTS -- 1 pair WING STRUT WIRE D3mm -- pcs M3 NYLON INSERT LOCK NUT -- pcs WASHER d3xd7mm -- 1 pcs WASHER d.5xd9mm -- pcs. FUSELAGE -- 1 pc. COVERING 30x550mm -- 1 pc. 5. STABILIZER & ELEVATOR -- 1 set SCREW PWM.5x1mm -- pcs STABILIZER WIRE Øx170mm -- pcs 6. VERTICAL FIN & RUDDER -- 1 set 7. TAIL GEAR ASSEMELY (PL310033) --1 set COPPER PLATE (For Stays on Tail Fueslage Bottom) 1.5x1x60mm -- 1 pc. SCREW PA3x18mm -- 3 pcs SCREW PWA.5x1mm -- pcs SPRING Ø5x50mm -- pcs 8. MAIN LANDING GEAR -- 1 set SCREW HMx0mm -- pcs SCREW PA3x18mm -- 1 pcs SCREW PAx0mm -- pcs WASHER dxd9mm -- pcs MOUNTING PLATE 1x0mm PL1100 -- 6 pcs ALUMINUM PLATE 3mm -- pcs 9. LARGE SCALE TREADED INFLATABLE WHEELS Ø118mm -- sets SCREW PA1.7x8mm -- 6 pcs SCREW PM3x1mm -- 8 pcs WASHER d3xd7mm -- 16 pcs M3 NUT -- 8 pcs COLLAR Ø5.1mm w/ set screw -- sets WIRE BRACKET PL5330050Y -- 8 pcs PLYWOOD x178x186.mm (Main Langing Gear Cover) --1 pair 10. BLIND NUT M5 -- pcs WASHER d5xd1mm -- pcs SOCKET HEAD SCREW M5x50mm -- pcs THROTTLE PUSHROD Ø1.8x30mm -- 1 pc. PLASTIC TUBE d.5xdx300mm -- 1 pc. 11. COWLING -- 1 pc. TRANSPARENT 3D TEMPLATE -- 1 pc. SCREW PA3x1mm -- pcs WASHER d3xd7mm -- pcs SILICON GROMMET d.5xd8.5mm -- pcs DUMMY ENGINE COVER -- 1 pair 1. FUEL TANK 800cc PL1111810G -- 1 set CABLE TIE 1.5x8x500mm -- 1 pc. DOUBLE-SIDED TAPE 0x160mm -- 1 pc. 13. PUSHROD M3xD5x170mm w/ Threads (For Elevator) -- pcs SOCKET HEAD SCREW Mx50mm -- pcs M NYLON INSERT LOCK NUT -- pcs SWIVEL CLEVIS HORN FAIRING PL610010 -- sets HEAVY DUTY HORN BRACKET PL1100 -- sets HEAVY DUTY SERVO HORN PL1050 -- sets HEAVY DUTY CLEVIS PL1100 -- sets 1. PUSHROD M3xD5x16mm w/ Threads (For Rudder) -- 1 pc. SOCKET HEAD SCREW Mx50mm -- 1 pc. M NYLON INSERT LOCK NUT -- 1 pc. SWIVEL CLEVIS HORN FAIRING PL610010 -- 1 set HEAVY DUTY HORN BRACKET PL1100 -- 1 set HEAVY DUTY SERVO HORN PL1050 -- 1 set HEAVY DUTY CLEVIS PL1100 -- set 15. SCREW PMx16mm -- 6 pcs WASHER dxd5mm -- 1 pcs M NUT -- 6 pcs FLYING WIRE CLEVIS -- 6 pcs SCREW PMx8mm -- 6 pcs WIRE Ø1x1700mm -- 1 pc. FLYING WIRE BRACKET -- 6 pcs EYE SCREW -- 6 pcs COPPER TUBE d.5xd3.x8mm (For Rudder) -- 8 pcs 16. WIND SHIELD & SIDE WINDOWS -- 1 set BALSA ROD Ø6x190mm -- pcs 17. LINKAGE CONNECTOR Ø.1mm w/ set screw -- 1 set 18. PLYWOOD 3x161.5x5mm (For Fuselage Servos) -- 1 set BALSA 10x10x0.5mm (For Fuselage Servo Stand) -- pcs SPONGE 10x80x00mm -- pcs 19. PILOT PC101110A -- 1 set SCREW PWAx1mm -- pcs COCKPIT BASE PANEL 3x161x373mm -- 1 set 0. M NYLON INSERT LOCK NUT -- pcs SCREW PMx1mm -- pcs WASHER dxd5mm -- pcs MOUNTING PLATE 5x15mm PL11015 -- pcs 1. WING TUBE Øx85mm -- pcs SELF-TIGHTENING LATCHING PIN PL910010 -- pcs WIRE Ø0.8mm -- pair M3x8mm SET SCREW -- pcs. SCREW HMx1mm -- pcs WASHER dxd1mm -- pcs M NYLON INSERT LOCK NUT -- pcs 3. DECALS: A037DEC -- 1 set COVERING: TOUGHLON STL 331 CUB YELLOW LIGHTEX SGX 01 BLACK A037PO798A109 P.
1 Main Wing Aileron Servo Lead Aileron Servos Mx60mm Socket Head Screw PWA.3x8mm Screw 8 Mx8mm Socket Head Screw PL10300 M Nylon Insert Lock Nut Heavy Duty Clevis M Nylon Insert Lock Nut M x 10mm M Nut 1.5mm Pushrod PWA.3x8mm Heavy Duty Horn Bracket M Nylon Insert Lock Nut M Nylon Insert Lock Nut 1.5mm Heavy Duty Clevis Pushrod M x 10mm M x 60mm Pushrod w/ Threads(For Aileron) M3xD5x113mm PA1.7 x 8mm Completed A037PO798A109 P.3
3 Wing Struts M3x18mm Socket Head Screw 8 17.5mm 3mm Mx18mm Socket Head Screw M3x18mm 389.mm 15mm 01.6mm 15.5mm d.5xd9mm M3 Nylon Insert Lock Nut d3xd7mm Mx18mm d3xd7mm 1 M3 Nylon Insert Lock Nut M3x18mm d3xd7mm d.5xd9mm Completed Fuselage Covering 30x550mm Completed A037PO798A109 P.
5 Stabilizer & Elevator PWM.5x1mm Screw A A' B B=B' (Stabilizer) B' (Main Wing) A=A' Temporary install the main wing, adjust leveling of the stabilizer to make it as parallel to the main wing as possible Stabilizer Tube Øx170mm PWM.5x1mm Completed 6 Vertical Fin & Rudder C C' C=C' Remove coverings for all surfaces in contact before applying A/B epoxy glue. Completed A037PO798A109 P.5
7 Tail Landing Gear PA3x18mm PWA.5x1mm Screw 3 Screw PA3 x18mm PWA.5 x 1mm Spring.5mm Copper Plate 1.5x1x60mm 1.5mm 8 Main Landing Gear PAx0mm Screw PA3x18mm HMx0mm dxd9mm Screw 1 Screw.5mm PA3x18mm HMx0mm PAx0mm dxd9mm ALU. Plate 3MM 9 Main Wheel PA1.7X8mm Screw 6 D5.1mm Collar PM3x1mm Screw 8 M3 Nut 8 d3xd7mm 16 Front Front M3 x 3mm Set Screw 5.1 mm Collar M3 x 3mm Set Screw Wire Bracket Ø5 d3xd7mm Mounting Plate Wheel Ø118mm 5.1 mm Collar Wheel Cover d3xd7mm PA1.7x8 mm PM3x1mm M3 Nut Main Langing Gear Cover A037PO798A109 P.6
10 Engine M5x50 SOCKET HEAD SCREW d5xd1mm Throttle Pushrod Ø1.8x30mm d5xd1mm M5x50 mm Plastic Tube d.5xdx300mm M5 Blind Nut M5 Blind Nut 11 Cowling PA3x1mm Screw Please refer to the attached sheet for usage of the transparent 3D template. First insert the grommet to the cowling then apply screw. d.5x8.5mm Silicon Grommet d3xd7mm 17mm 6.77 in. Dummy Engine Cowling Fuselage Cowling d3xd7mm PA3x1mm d.5x8.5mm Silicon Grommet Completed 1.5mm A037PO798A109 P.7
1 Fuel Tank Cable Tie 1.5x8x500mm 1 3 Double-sided Tape 0x160mm Fuel Tank 800cc UP Completed 13 Elevator Pushrod Mx50 SOCKET HEAD SCREW M NYLON INSERT LOCK NUT Heavy Duty Servo Horn M Nylon Insert Lock Nut M x 10mm Pushrod Mx8mm Socket Head Screw PL10300 Heavy Duty Horn Bracket M Nylon Insert Lock Nut M Nylon Insert Lock Nut Heavy Duty Clevis Pushrod M x 10mm M Nut M x 50mm PA1.7 x 8mm 1 Rudder Pushrod Pushrod M x 10mm M Nylon Insert Lock Nut Mx50 SOCKET HEAD SCREW 1 M NYLON INSERT LOCK NUT 1 Heavy Duty Servo Horn PA1.7 x 8mm Mx8mm Socket Head Screw PL10300 M x 50mm Heavy Duty Clevis M Nylon Insert Lock Nut M Nut M Nylon Insert Lock Nut Pushrod M x 10mm Heavy Duty Horn Bracket PA1.7 x 8mm A037PO798A109 P.8
15 Flying Wire PMx16mm Screw 6 PMx8mm PMx8mm Screw 6 M dxd5mm Nut 6 1 PMx16mm M Wire Press down the center 1/3 portion PMx16mm dxd5mm mm Copper Tube mm d.5xd3.x8mm M NUT 16 Windows Securely glue the windows to the fuselage. Balsa Rod d6x190mm 17 Servo Set 3x3mm 3x3mm Set Screw 1 Linkage Connector 1 M Nut 1 mm Throttle Pushrod 1.5mm mm mm M Nut Throttle Servo. Please refer to the attached sheet for linkage connector installation. A037PO798A109 P.9
18 Radio Equipment lnstall and arrange the servo as shown in the diagram. Plywood 3x161.5x5mm Battery Battery Plastic tube d.5xdx300mm Balsa 10x10x0mm Sponge Receiver Throttle Servo Throttle Pushrod D1.8x30mm 19 Pilot PWA x1mm Screw Instrument Panel PWAx1mm Screw PC101110A 0 Wind Shield PMx1mm Screw M Nylon Insert Lock Nut d x D5mm dxd5mm Mounting Plate M Nylon Insert Lock Nut dxd5mm PMx1mm A037PO798A109 P.10
1 Main Wing M3 x 8mm Set Screw Lead to Aileron Servo Wing Tube Øx85mm Wire Ø0.8mm Set Screw M3x8mm Self Tightening Wing Latch Set Screw M3X8mm Wing Tube PWAx8mm Completed Wing Struts PMx1mm dx D1mm Screw M NYLON INSERT LOCK NUT HMx1mm dxd1mm M NYLON INSERT LOCK NUT A037PO798A109 P.11
3 Wing Setting Adjust the wing and fuselage configuration as shown in the diagrams. A A' A = A' B B' C C' B = B' C = C' A037PO798A109 P.1
Control Throws Rudder Elevator 60mm 60mm Adjust the control throws as shown in the diagram. These throws are good for general flying. You can adjust according to your personal preference. 5mm 5mm Aileron 35mm 35mm 5 C.G. The ideal C.G. position is 1mm (.9in.) behind the leading edge measured at where the wing meets the fuselage. In order to obtain the C.G. specified, add weight to the fuselage or move the battery position. Check the C.G. before flying. If you are converting this model to electric, please move the C.G. forward 10% of current C.G. distance from leading edge to compensate for weight of fuel. 1 mm.9 in. C.G. http://www.theworldmodels.com/para/instruction/instructionmanuals.php Warning! Important Safety Precautions # First time flyer should never fly by himself / herself. Assistance from experienced flyer is absolutely necessary. # Pre-flight adjustment must be done before flying, it is very dangerous to fly a badly pre-adjusted aircraft. # is specially designed to be powered by 50c.c. gasoline engine, using a more powerful engine does not mean better performance. In fact, over powered engine may cause structural damage and injuries. # Make sure the air field is spacious, never fly the plane too close to people and never get too close to a running propeller. # If you find wrinkles on the covering as a result of weather changes, you can use hot iron to remove the wrinkles. Please begin with lower temperature setting and gradually raise the temperature until the wrinkles are gone. Too hot an iron may damage the covering. Don't use hot iron near the seams or edges, hot iron will melt the glue and shrink the covering at the same time, causing the seams to pull away. # Check and re-tighten up all factory assembled screws, use thread locker if necessary. A037PO798A109 P.13
Usage of the transparent 3D template This transparent 3D template is used for position guidance of the actual cutting of the pre-painted cowling. 1 3 Simply cut the transparent 3D template to fit your engine and exhaust pipe, then slide onto the actual cowling and use as template to mark the openings required for final cutting. A037PO798A109
A037PO798A109