residential & commercial Generators

residential & commercial Generators Guardian Series QuietSource Series

Why choose Generac? Generac is known exclusively for generators. With a sole focus on power generation for over 50 years, our reputation as the generator experts has grown to include portable, RV, residential, commercial and industrial generators. Today, Generac is the undisputed leader, preferred five to one over the closest competition. Generac s OHVI engine the only engine designed specifically for extended generator use, not lawn and garden applications. Powers our most popular standby and many of our portable generators. Extensive, nationwide dealer network specializing in generators. Broadest home generator product line install the exact solution for any backup power need. Easiest installation on the market with our pre-wired solutions. Generac s standby and portable generators have earned the Seal after review by the Good Housekeeping Research Institute. The OHVI engine. The Power Behind the #1 Home Standby Generator The only engine designed specifically for generator use. Why is this important? Generators are often required to run for hours at a time, day after day. Generac s OHVI engine utilizes the same type of pressurized oil lubrication used to give automobile engines long and trouble free lives. This means a significantly longer life than competitive engines - an unprecedented three to four times longer. That s the reliability you need for the long run times emergency backup can require. Generac s OHVI engine powers all air-cooled and many portable generators. Generac OHVI engine Low Oil Pressure Protection When low oil level or overheated oil is detected, engine shuts down to prevent damage. Pressurized Lubrication System Positively lubricates from start-up to shut-down by pumping oil directly to every critical area. Automotive Grade Spin-on Filter Full pressure lubrication system allows for use of automotive grade oil filter to remove dirt and carbon solids. X-Torque TM Governor Fastest responding governor available. Maximizes engine performance and virtually eliminates stalling. OHV/Lawn mower engines No Oil Level Protection Engine continues to run even when oil level is low, possibly causing serious damage. Splash Lubrication Internal engine action splashes oil on moving parts, missing critical friction areas. No Filter Many OHV engines do not have oil filtration, relying only on oil changes to drain out impurities. This allows harmful debris to end up in the engine. Slow Governor A slow governor can result in poor/low voltage, potentially damaging to electronics.

A generator system for everyone. With the broadest product line in the industry, Generac ensures the best possible backup power system for every homeowner. The table below provides examples of how much power various necessities require. Take some time to consider homeowner requirements to develop an accurate solution. hvac bedroom 8 kw 10 kw 14 kw 17 kw 20 kw + Air Conditioning 3-ton 3-ton up to 4-ton* up to 5-ton* up to 5-ton* Kitchen n n n n n Furnace n n n n n Sump Pump n n n n n Number of Bathrooms Backed Up 1 1 1 2 2+ Number of Bedrooms Backed Up 1 2 2 3 3+ Family Room n n n n n Well Pump or Water Heater n n n n Home Office n n n Garage n * For multiple A/C units check with your installer for installation options. Rooms and appliances indicated here are for example only. Professional sizing is recommended. commercial models also available. lights kitchen Cover just the basics. Many homeowners choose to cover only a minimum number of rooms during a power outage. Generac s smaller kw units fit these requirements perfectly and are remarkably economical for example, an 8 kw can be purchased for less than $2000 plus installation to maintain power for essential needs. home entertainment Back up the whole house. Generac s full line of backup power solutions include larger generators capable of covering every circuit in any size home for true whole house protection. More coverage with less generator. Gain up to whole-house coverage through Load Shedding Power Management. If it is unlikely every appliance will be used at the same time, a smaller generator paired with a Generac load shedding switch is a cost effective option.

GUARDIAN SERIES 8-20 kw

The #1 selling generator. Standby Power for Residential Applications Powered by Generac s OHVI engine, these units are built for reliability and long life, with a continuous fuel source from the existing LP or natural gas supply. With standard features competitor s don t have, it s easy to see why Generac automatic home standby generators are the number one choice in 24/7 power outage protection. A Weekly Self-test that Won t Wake the Neighbors. All automatic standby generators perform a weekly self-diagnostic test to validate proper operation. Quieter than the competition, only Generac s patented, programmable Quiet-Test mode kicks in for an ultra-quiet, neighborhood-friendly self-test. Safe for Sensitive Electronics. TruePower Technology provides confident operation of sensitive electronics such as heating, cooling, home theaters and computers. Less than 5% total harmonic distortion gives smooth and consistent electrical power quality and performance. Harsh Weather Conditions? Bring It On. Generac s patented galvanneal steel enclosures with RhinoCoat provide substantial protection from the elements. For added protection, the all-weather aluminum enclosure s corrosion resistance prolongs the life of your generator in salt air coastal communities. Generator Extras 10 20 kw features: System status LED light Emergency shut-off breaker 17 and 20 kw feature: External GFCI Outlet - safely plug in additional equipment for added flexibility during an outage. Added Sound Reduction Generac enclosures are lined with sound reducing foam panels for even further reduction in noise levels. User-Friendly Controls Electronic Controller and user-friendly, trilingual LCD display and controls for programmable diagnostics and information at-a-glance. Sophisticated codes alert you to generator status at all times. Base Fascia In addition to completing the stylish look of the generator, the base fascia provides added protection against debris and rodents. Standard on 20 kw, optional on 8-17 kw.

Guardian Series 8-20 kw System Options With Generac s Guardian Series of standby generators, homeowners can be assured their system will provide the amount of coverage they expect. Needs can be matched to a prepackaged system, or a custom system can be designed with the help of a dealer or contractor. Best Value and Easiest Installation or 8, 10, 14 and 17 kw 20 kw Prepackaged, Pre-wired Systems Essential Circuits through Whole House Coverage The best value and simplest installation on the market. The generator is installed in just a few hours. Easily match the correct system to homeowner s needs. Pre-packaged with 100 Amp transfer switch that is color-coded, numbered and labeled to easily match with existing circuits in the main service panel. Choose Your Generator & Transfer Switch Separately or or custom Solutions Essential Circuits through Whole House Coverage Generac offers the most generator and transfer switch options in the industry. Purchase components separately for flexibility to ensure a perfect system for any home. Includes units capable of providing whole house coverage for larger sized homes. Transfer switches available to meet codes in all areas of the country. More Power with a Smaller Generator or Load Shedding Whole House Coverage Pair a smaller generator with one of Generac s power management options and gain up to whole house coverage through load shedding. non-essential circuits are shed when generator approaches maximum capacity to eliminate overload. These cycle back on when essential circuits have been satisfied.

8, 10, 14 & 17 kw Cover your home s essential circuits with the #1 selling home standby generator. automatic, hands-free backup power supply for home or business. kicks in within ten seconds of determining power loss. Easiest installation and best value on the market - many models pre-packaged with a 100 Amp pre-wired transfer switch. All models include mounting pad. TruePower Technology provides clean, smooth operation of sensitive electronics and appliances. Quiet-Test mode for a weekly self test that s quieter than other brands. Simple field conversion from LP to natural gas. 17 kw offers optional aluminum enclosure and includes external GFCI outlet. System status LED light and main circuit breaker (10 20 kw). 20 kw One of the most powerful air-cooled generators on the market today, this unit provides whole house power protection for many homes. Additional features include: aluminum enclosure is standard. Recommended for coastal climates. Base fascia for added protection against debris and rodents. Pre-packaged unit comes with the 200 Amp service entrance rated transfer switch for whole house coverage. External GFCI outlet

GUARDIAN SERIES 22-60 25-60 Kw

Standby protection for home or business. As the world s number one manufacturer of home standby systems, Generac identified and responded to the need for affordable, higher kw units for larger residences and smaller businesses. Through innovative engineering, Generac has eliminated the noise, cost, and environmental issues that once made standby power impractical for these applications. When more power is necessary, install a quiet, clean and affordable solution from Generac. The solid, reliable, increased horsepower of an automotive-style, liquid cooled engine provides whole house power protection for larger homes, and small to medium size businesses such as convenience stores, restaurants and offices. continuous fuel choices in LP and natural gas are cleaner burning fuel solutions than the traditional diesel engines. The best liquid cooled engine packs more power into less footprint than competitive models. Neutral styling, color and small footprint fits unobtrusively into landscaping. Single phase Need three phase options or more than 60 kw? Ask about Generac s commercial custom generators. RhinoCoat Our RhinoCoat finish system uses a process that evenly joins paint particles to every part of the metal surface. Components are then baked to form a lasting bond for superior protection against the elements. This process allows for more consistent coverage to all surfaces for exceptional protection on not only the enclosure, but also the base frame. Patented Quiet-Test Mode All automatic standby generators perform a weekly self-diagnostic test to validate proper operation. Quieter than the competition, only Generac s patented, programmable Quiet-Test mode kicks in for an ultra-quiet, neighborhood-friendly self-test. Hour Meter The hour meter allows for run time monitoring to determine maintenance intervals.

QUIETSOURCE SERIES 22-48 Kw

The premium in home or business backup. QuietSource Series 22, 27, 36, 48 kw Premium features are standard on the ultimate standby generator. For discerning homeowners with larger residences, these units are powered by a low speed engine for extra quiet operation and come standard with an aluminum enclosure. QuietSource generators also include all the features of the Guardian Series 25 60 kw. Ideal for homes requiring higher kw backup for amenities such as additional living areas, garages and air conditioners, pools, greenhouses, guest houses, mother-in-law suites, medical needs and more. Powerful low-speed, liquid-cooled engine is engineered to run at only 1800 rpm for a substantially quieter generator, consuming less fuel and giving both the engine and alternator a longer life. Standard aluminum, all-weather enclosure provides the ultimate protection from the elements. Aluminum s corrosion resistance prolongs the life of your generator and is highly recommended for salt-air, coastal locations.

200 AMP LOAD SHEDDING AUTOMATIC TRANSFER SWITCH UTILITY SERVICE DISCONNECT INSIDE NEMA 3R - INDOOR/OUTDOOR RATED AUTOMATIC TRANSFER SWITCHES Generac designs and manufactures a complete line of automatic transfer switches to meet the requirements of virtually any emergency standby application and codes in all areas of the country. All switches are UL 1008. Pre-wired Transfer Switch Generac s Distributed Load Center is the answer for homeowners who choose to backup selected circuits rather than an entire house. Pre-wired, they are the easiest installation on the market and offer the greatest value. Available with 8, 10, 12, 14 or 16 circuits 30 ft. pre-wired conduit for connecting the transfer switch to the external connection box 2 ft. pre-wired conduit for moving circuits from the main panel to the transfer switch Pre-wired external connection box with a weatherproof conduit for generator connections RTS Transfer Switches RTS transfer switches are designed for a wide variety of applications requiring up to 400 Amps. The RTS is integrated with the R-Series digital controller and operates only with standby generators through 60 kw. NEMA 3R (outdoor rated) enclosures are standard. (Shown without cover) RTS-E with Service Disconnect (Single-Phase) Use RTS-E models with service disconnect for quick and easy installations. 100, 200, or 400 Amp Service-entrance rated and UL Listed (U.S. only) RTS-N (Single and Three-Phase) Use RTS-N models for custom installations or with applications that require a sub-panel. 100, 200, or 400 Amp RTS-S models RTS-E models RTS-N models Use RTS-S and RTS-E models with service disconnect for quick and easy installations. Use RTS-N models for custom installations or with installations that require a sub panel.

Load Management PowerManager LTS Load Shed Switch Pair a smaller generator with the PowerManager switch and gain up to whole house coverage through load shedding. This switch cycles off non-essential circuits when the generator approaches overload condition, allowing essential circuits to remain powered. When essential circuit demand is satisfied the non-essential circuits are powered back on. 200 Amp, service-entrance rated Aluminum NEMA 3R outdoor-rated enclosure Load shedding capability 16 circuit load center built-in PowerMaster Load Shedding device Add the PowerMaster Load Shedding device to existing generator systems and manage two large electrical loads instead of only one, such as an air-conditioner and an electrical water heater. Locks out non-essential load until demand for the essential load is satisfied Compatible with Generac models up to 60 kw Up to 6 may be used with a single generator for 12 managed circuits GenReady Load Center Simplicity and Savings for New Home Building Traditional Installation New home construction or renovations with electrical upgrades are the ideal time to install Generac s GenReady Load Center. Enjoy substantial savings on installation and a simplified generator system. 200 Amp Main Load Center 42-Space Automatic Transfer Switch Emergency Load Center The advanced engineering of the GenReady Load Center replaces the home s main circuit panel and incorporates the automatic transfer switch in the form of the EZ Transfer Operator with the emergency panel. All power switching is handled within one unit. It becomes a hybrid circuit panel capable of separating out only the electrical circuits chosen to be backed up during a power outage. 40 circuit capacity with the use of tandem breakers Dimensions same as a standard 42-circuit main load center Utilizes standard Siemens Load components Compatible with generators rated up to 125 Amps/30 kw UL Listed, Single-Phase applications only 2 panels can be used together to accommodate a 400 Amp service GenReady Installation GenReady Installation Levels Basic Advanced Complete The innovative GenReady load center combines three boxes into one, saving space and money on generator installations! basic installation Install only the GenReady Load Center instead of a traditional distribution panel for a considerable reduction in installation costs when a generator is added in the future. Complete installation Install the GenReady Load Center and a Generac standby generator for substantial savings in equipment and labor charges compared to a traditional installation. EZ Transfer Operator Locks out non-protected circuits during an outage, allowing the generator to power only the essential circuits. GenReady Panel

ACCESSORIES

Remote Wireless Monitor for Air-Cooled Generators Add convenience and efficiency by allowing for remote viewing of generator status and parameters from inside the home. Scheduled Maintenance Kits A scheduled maintenance program will ensure that the generator system is always in top operating condition and that your warranty requirements are met. Generac offers a comprehensive line of scheduled maintenance kits to ensure long life and top performance of your generator system. Cold Weather Kit Cold weather kits are recommended for areas where the temperature drops below 30 F. Fascia for Air-Cooled Units Complement the enclosure with a fascia base wrap that snaps together around the bottom of the generator. Fits air-cooled generators manufactured after April 2008. Fascia continues the sleek, contoured appearance as well as offering protection from rodents and debris by covering the lifting holes located in the base. Available in grey only. Standard on 20 kw air-cooled model. Generator Transport Cart for Air-Cooled Units Moving a 400 lb generator can be hard work. The Generator Transport Cart will assist with moving the generator from the truck to the planned installation site. Allows for a single person to easily maneuver any air-cooled product to the desired installation location. 5-Year Extended Warranty A 5-Year Extended Warranty is available for Generac automatic standby generators.

Guardian Series Residential Generators Pre-packaged model 5501 5502 5503 5504 5505 5744 Non pre-packaged models 5518 5520 5522 5523 5524 5525 Rated Power (LPG/NG) 8/7 kw 10/9 kw 14/13 kw 17/16 kw 17/16 kw 20/18 Voltage (Single Phase) 120/240V 120/240V 120/240V 120/240V 120/240V 120/240V Amps @ 240V LPG 33.3 41.6 58.3 70.8 70.8 83.3 Amps @ 240V NG 29.2 37.5 54.2 66.6 66.6 75 Engine/Alternator RPM 3600/3600 3600/3600 3600/3600 3600/3600 3600/3600 3600/3600 Engine OHVI / 410cc OHVI / 530cc OHVI / 992cc OHVI / 992cc OHVI / 992cc OHVI / 999cc Fuel Consumption LPG 62 (1.68) 70 (1.93) 84 (2.36) 94 (2.57) 94 (2.57) 1065 (2.9) Fuel Consumption NG 139 156 80 (2.18) 245 245 262 Quiet-Test Mode No No No Yes Yes Yes db(a) at exercise 62 63 66 60 60 60 db(a) at normal operating load 62 63 66 66 66 66 Automatic Transfer Switch 100 Amp 100 Amp 100 Amp 100 Amp 100 Amp 200 SE Rated Circuits Included 8 10 14 16 16 NA Enclosure Steel Steel Steel Steel Aluminum Aluminum Enclosure Color Bisque Bisque Bisque Bisque Gray Gray Dimensions (L" x W" x H") 48 x 24 x 29 48 x 24 x 29 48 x 24 x 29 48 x 24 x 29 48 x 24 x 29 48 x 24 x 29 Generator Weight (lbs.) 336 375 425.5 445 414 451 Transfer Switch Weight (lbs.) 62 72 78 80 80 70 CARB Model Larger Residential and Small Business Generators Model QT02516ANSN QT03016ANSN QT04524ANSN QT04524ANSY QT06024ANSN QT06024AVSN Rated Power (LPG/NG) 25/24 kw 30/29 kw 45/45 kw 45/45 kw 60/60 kw 60/60 kw Voltage (Single Phase) 120/240V 120/240V 120/240V 120/240V 120/240V 120/240V Amps @ 120/240V LPG 208.3/104.2 250/125 375/187.5 375/187.5 250 N/A Amps @ 120/240V NG 200/100 241.6/120.8 375/187.5 375/187.5 N/A 250 Engine/Alternator RPM 3600/3600 3600/3600 3600/3600 3600/3600 3600/3600 3600/3600 Engine In-line 4-Cyl. In-line 4-Cyl. In-line 4-Cyl. In-line 4-Cyl. V6 V6 Fuel Consumption LPG 175 (4.81) 209 (5.7) 286 (7.86) 286 (7.86) N/A 376.3 (10.34) Fuel Consumption NG 437 525 720 720 862 N/A Quiet-Test Mode Yes Yes Yes Yes Yes Yes db(a) at exercise 62 62 61 61 65 65 db(a) at normal operating load 74 75 73 73 72 72 Enclosure Steel Steel Steel Steel Steel Steel Enclosure Color Bisque Bisque Bisque Bisque Bisque Bisque Dimensions (L" x W" x H") 62.2 x 29 x 33.5 62.2 x 29 x 33.5 77 x 33.5 x 45 77 x 33.5 x 45 77 x 33.5 x 45 77 x 33.5 x 45 Generator Weight (lbs.) 875 935 1414 1464 1650 1650 SCAQMD Model QuietSource Series Model QT02224ANAN QT02724ANAN QT03624ANAN QT04824ANAN Rated Power (LPG/NG) 22/22 kw 27/25 kw 36/35 kw 48/46 kw Voltage (Single Phase) 120/240V 120/240V 120/240V 120/240V Amps @ 120/240V LPG 183.3/91.6 225/112.5 300/150 400/200 Amps @ 120/240V NG 183.3/91.6 208.3/104.2 292/146 384/192 Engine/Alternator RPM 1800/1800 1800/1800 1800/1800 1800/1800 Engine In-line 4-Cyl. In-line 4-Cyl. In-line 4-Cyl. V-6 Fuel Consumption LPG 120 (3.3) 149 (4.1) 196 (5.4) 261 (7.20) Fuel Consumption NG 316 359 503 661 Quiet-Test Mode Yes Yes Yes Yes db(a) at exercise 61 61 58 60 db(a) at normal operating load 70 70 64 65 Enclosure Aluminum Aluminum Aluminum Aluminum Enclosure Color Gray Gray Gray Gray Dimensions (L" x W" x H") 62.2 x 29 x 33.5 62.2 x 29 x 33.5 77 x 33.5 x 45 77 x 33.5 x 45 Generator Weight (lbs.) 843 891 1312 1703 SCAQMD Model

Transfer Switches Model LTS Load Shedding Switch RTSD100A1 RTSF100A1 RTSH100A1 RTSP100A1 RTSW100A1 RTSN100A3 RTSE100A3 Amp Rating 200 100 100 100 100 100 100 100 Load Transition Type Open Open Open Open Open Open Open Open Transition w/ Service Disconnect Voltage 120/240 120/240 120/240 120/240 120/240 120/240 120/240 120/240 Phase Single Single Single Single Single Single Single Single Enclosure Type NEMA 1/3R NEMA 1 NEMA 1 NEMA 1 NEMA 1 NEMA 1 NEMA 3R NEMA 3R Dimensions H" x W" x D" 42 x 20 x 7.25 26.5 x 12.5 x 7.5 26.5 x 12.5 x 7.5 26.5 x 12.5 x 7.5 26.5 x 12.5 x 7.5 26.5 x 12.5 x 7.5 20 x 15 x 7 (2) 23.5 x 13.05 x 7 (2) Weight (lbs) 80 62 72 76 78 80 35 52 Model RTSN200A3 RTSE200A3 RTSN400A3 RTSE400A3 Amp Rating 200 200 400 400 Load Transition Open Open Transition w/ Service Disconnect Open Open Transition w/ Service Disconnect Voltage 120/240 120/240 120/240 120/240 Phase Single Single Single Single Enclosure Type NEMA 3R NEMA 3R NEMA 3R NEMA 3R Model 5448 GenReady 5447 EZ Transfer Operator 5449 GenReady with EZ Transfer Operator Amp Rating 200/125 N/A 200/125 Number of Circuits 40 N/A 40 Breakers N/A N/A N/A Load Transition Type N/A Open Open Voltage 120/240 N/A 120/240 Phase Single N/A Single Enclosure Type NEMA 1 N/A NEMA 1 Dimensions (H" x W" x D") 42 x 15 x 4 N/A 42 x 15 x 4 Weight (lbs) 45.5 3.5 49 Accessories Air-cooled Remote Monitoring Options Model Description 5636 Remote wireless monitor Air-cooled Scheduled Maintenance Kit Model Description 5661 7 kw, 410 cc kit 5662 8 kw, 410 cc kit 5663 10 kw, 530 cc kit 5664 12,13, 14,15, 16 kw, 17 & 18 kw, 760/990cc kit 5665 20 kw, 999 cc kit Liquid-cooled Scheduled Maintenance Kit 18 kw low speed aluminum, 20, 25 & 30 kw steel, 5655 3600 RPM units, 1.6L 5656 25 kw low speed aluminum & 45 kw steel, 3600 RPM units, 2.4L 5657 60 kw unit, 3.0L 5658 35 & 45 kw low speed, aluminum, 4.2L Miscellaneous Model Description 5651 Base plug for all liquid-cooled models 5652 Base plug for all air-cooled models mfg prior to 4/08 5654 Grey paint kit Units mfg prior to 4/08 5653 Tan paint kit Units mfg prior 4/08 5703 Bisque paint kit Units mfg after 4/08 5704 Medium grey paint kit Units mfg after 4/08 5685 Air-cooled generator transport cart 5666 Fascia for air-cooled units mfg after 4/08 Load Management Options Model Description Contents 5239 PowerMaster load shedding device PowerMaster 5621 Auxiliary transfer switch contact kit Contact, screws, and washers Air-cooled Cold Weather Kit Model Description Contents 5634 For air-cooled units mfg prior to 4/08 Battery wrap with internal thermostat 5635 For air-cooled units mfg after 4/08 Battery wrap with internal thermostat Liquid-cooled Cold Weather Kit 5629 For 1.6L engines 28 Battery warmer w/oil filter 5630 For 2.4L engines 28" Battery warmer, zip ties, thermostat 5631 For 4.2L engines 44" Battery warmer, zip ties, thermostat 5632 For 3.0, 4.6, 7 6.8L direct drive units 44" Battery warmer, zip ties, thermostat 5633 For 6.8L gear drive units 44" Battery warmer, zip ties, thermostat & gear oil Liquid-cooled Extreme Cold Weather Kit Model Description Contents Use with 5615 18 kw (3600 rpm), 20, 25, 30 kw (1.6L) 5616 25 kw (1800 rpm), 45 kw (2.4L) 5618 35 & 45 kw - both 1800 RPM (4.2L) 5617 60 kw (3.0L) Block heater & associated mounting hardware Block heater & associated mounting hardware Block heater & associated mounting hardware Block heater & associated mounting hardware 5629 5630 5631 5632

Commitment to Service Generac is committed to providing our customers with unsurpassed after-the-sale service and support. Our nationwide dealer network has factory trained technicians on staff and maintains large inventories of Generac parts, components and accessories. Our state-of-the-art training center ensures that Generac service technicians are always up to date on new product innovations and improvements. Technicians receive comprehensive technical training and extensive hands-on experience in the installation, repair and maintenance of Generac products. Generac s commitment to service includes scheduled maintenance programs, warranty assistance and emergency service to ensure that Generac customers are never left powerless. A Tradition of Quality and Innovation For over 50 years, Generac Power Systems has led the industry with innovative design and superior manufacturing. When it comes to developing products that are both durable and reliable, we stand head and shoulders above our competition. That s because our sole focus has been, and continues to be, standby power. The result of our efforts can be seen in every inch of our product offerings. We design and build our own air-cooled engines, alternators, control systems, automatic transfer switches, enclosures and base tanks. Our vertical integration allows us to control the quality, availability and flow of materials throughout the manufacturing process. Our products are fully integrated as complete power systems and each genset is factory tested prior to shipment. Because of our ongoing commitment to quality and innovation, Generac is the name that home and business owners have come to trust. Bulletin 0183170SBY Printed in USA Rev. 07/09 2009 Generac Power Systems, Inc. All rights reserved. Specifications are subject to change without notice Generac Power Systems, Inc. S45 W29290 Hwy. 59 Waukesha, WI 53189 1-888-GENERAC (1-888-436-3722) Generac.com