Platform Cylinder Series ø, ø, ø, ø, ø, ø highly rigid and highly accurate slide table integrated with an actuator. Two types of guide rod bearings to accommodate your application For heavy loads all bushing bearing For highly accurate and smooth operation uto switch can be mounted. shock absorber can be installed (option). Can be mounted on two sides. Mounting from the upper side Mounting from the bottom side djusting bolt with bumper is standard. Performs the function of a cushion and adjusts the stroke mm on each side, or mm for both sides. For moving and transferring workpieces. Series Variations Slide bearing M M M earing type all bushing bearing For moving the receptacle for workpieces used in stamping or press-fitting processes. For using as a Pick & Place unit in combination with other actuators. Stroke 0 7 0 1 0 17 0 0 300 Guide of high rigidity Series Maximum M () (all bushing bearing) load weight (1) Table llowable () Table (1) llowable () displacement static mass displacement static mass (kg) (kg) (kg) 3 7 30 0 Note 1) Table displacement 0.00 0.004 0.007 0.030 0.0 0.0 Note ) llowable static weight 30 00 900 900 10 1900 0.0 0.019 0.044 0.180 0.3 0.9 0 70 1 1 1 170 Table displacement is the amount of deflection of the guide rod that occurs when a maximum load weight is placed on the maximum stroke table while the table is at the center of the stroke (the amount of looseness is not included). n allowable static mass the allowable amount of static mass that can be applied vertically to the workpiece mounting surface of the table while the table is at the stroke end. CX CX CXSJ CXS M M M Standard stroke ong stroke 709 D- -X
Selection Step Series Model Selection NO Setting Conditions 1. Mounting (Horizontal, Inclined, Vertical). oad mass (kg) 3. Operating pressure P (MPa) P 0.7 MPa 4. Speed V (mm/s) V 00 mm/s Selection of bearing type Provisional selection of cylinder bore size Confirmation of sum of load ratio to the guide unit Σαn 1 YES Calculation of resistance force f Guideline for Selection of earing Type earing type Required conditions all bushing bearing Impact load and vibration load are added. Change in load is large. ong life span is required. High accuracy (ittle rattle is allowed.) Smooth operation oad mass [] Moment [mn] Σαn = + Maximum load mass [max] llowable moment [Mn] oad mass [] are as follows in compliance to the mounting way. Horizontal mounting: Inclined mounting: cosθ (θ: ngle of inclination, refer to the figure below.) Vertical mounting: 0 (None) The moment load rate must be calculated in accordance with the above formula for all types, M1 to M3. s for max and Mn, refer to the maximum load weight and allowable moment table in the next section. The moment for the inclined mounting must be calculated taking the moment caused by the load into consideration. Note) Make sure that the distance between the guide shaft center to the center of gravity of the load does not exceed the distance GP between the guide shafts given in the table below. If the distance must be exceeded due to unavoidable circumstances, decrease the load rate that is applied to the guide as indicated below in order to determine the distance. 1 Σαn (/GP) (Provided that > GP) β > 0. Calculation of theoretical output F Calculation of load ratio β to the theoretical output of cylinder β = f/f β 0. Confirmation of adjusting bolt capacity Refer to Theoretical Output on page 713. NO GP Distance between guide rods GP 0 Horizontal mounting: f = µ x Inclined mounting: f = µ x cosθ + sinθ (Refer to the figure on the right.) Vertical mounting: f = µ = 0.3 () µ = 0.1 (all bushing bearing) Determine the movable weight which can be operated only by adjusting bolts. θ 80 90 1 130 θ YES Model selected ithout shock absorber Model selected ith shock absorber 7
Model Selection Series Non-rotating ccuracy of Slide lock θp θr θy Pitching direction Rolling direction Yawing direction Maximum oad Mass and llowable Moment M () (all bushing bearing) θp (= θy) θr θp (= θy) θr ± 0.09 ± 0.08 ± 0.07 ± 0.07 ± 0.08 ± 0.0 ± 0. ± 0. ± 0.08 ± 0.07 ± 0.07 ± 0.0 ± 0.0 ± 0.0 ± 0.04 ± 0.04 ± 0.04 ± 0.03 ± 0.0 ± 0.04 ± 0.03 ± 0.03 ± 0.03 ± 0.03 earing all bushing bearing all bushing bearing all bushing bearing all bushing bearing all bushing bearing all bushing bearing Maximum load mass max (kg) 3 7 30 0 llowable moment (N m) M1 (= M3) M 1. 1.8 0.3 0.70 3.34 4. 1.3.11 11.4 17.1.0 7.8 11.4 19.3.0 8.19 19.8 3.3.1 14.8 37.3 4. 1.3 7. M1 dimension 19. 4 M 8 31 M3 Note) For the purpose of calculating the moment, the length of the arm is the distance that is measured from the guide shaft center ( mark). Dimension from the guide shaft center to the top surface of the table is indicated below. 39. 47. llowable oad Only by djustment olt If only the adjustment bolt is used for stopping the load, make sure that the load weight and the speed will be below the curve in the graph on the right, taking into consideration the durability of the rubber bumper that is attached to the end of the adjustment bolt and the vibration and noise that are created when stopping (provided that the maximum load weight is not exceeded). In conditions in which the load weight and the speed will be above the curve, use a shock absorber (provided that the maximum load weight not exceeded). Caution In the case of the ball bushing type, the service life could be drastically shortened if shocks or excessive moments are applied. Therefore, even if the conditions given above are not exceeded, the use of a shock absorber is recommended. oad weight (kg) 0 4 3 30 0 0 0 300 0 00 Speed (mm/s) Static Movable Mass when Stopped hen the series cylinder is used for moving the workpiece receptacle, such as in a stamping or press-fitting process, a vertical load will be applied to the top surface of the stopped slide block (refer to the figure on the right). In this case, the allowable mass is greater than the maximum load weight, as given in the table on the right. Caution 1. Make sure that the slide block is stopped at the stroke end.. Match the center of the mass to be applied with the center of the slide block. The direction of the mass must be vertically downward in relation to the surface on which the workpiece is mounted, as shown in the figure on the right. 3. Do not apply a load that involves shocks such as those caused by pounding (particularly with the ball bushing type). 4. If this mass is applied, the deflection of the guide shaft will also have a large value. llowable Static Mass (kg) M () (all bushing bearing) 30 00 900 900 10 1900 0 70 1 1 1 170 711 CX CX CXSJ CXS D- -X
Platform cylinder M Nil TN TF M 0 earing type all bushing bearing Port thread type M thread ø to ø Rc NPT ø, ø G /Stroke Stroke 0 7 0 1 0 17 0 0 300 Standard stroke ong stroke For minimum strokes for auto switch equipped type, refer to page 718. Platform Cylinder Series ø, ø, ø, ø, ø, ø How to Order Shock bsorbers uto switch Nil ithout auto switch (uilt-in magnet) For the applicable auto switch model, refer to the table below. Option pplicable uto Switches/Refer to pages 1119 to 4 for further information on auto switches. Type Solid state auto switch Reed auto switch Special function Diagnostic indication (-color indicator) ater resistant (-color indicator) Magnetic field resistant(-color indicator) Electrical entry Grommet Grommet Since there are other applicable auto switches than listed, refer to page 7 for details. For details about auto switches with pre-wired connector, refer to pages 119 and 1193. Indicator light Yes Yes No iring (Output) 3-wire (NPN) 3-wire (PNP) -wire 3-wire (NPN) 3-wire (PNP) 4 V -wire 3-wire (PNP) 3-wire (PNP) -wire -wire (Non-polar) 3-wire (NPN equivalent) -wire 4 V Nil S M9 Standard (shock absorber R series) Shock absorber soft type RJ series type (-X) Made to Order Refer to page 713 for details. Number of auto switches Nil S n pcs. 1 pc. n pcs. djusting bolt with bumper only (Standard) ith shock absorbers (Set on the driving cylinder side only when packed.) ith 1 shock absorber (Set on the driving cylinder side when packed.) 1 ater resistant type auto switches can be mounted on the above models, but in such case SMC cannot guarantee water resistance. Consult with SMC regarding water resistant types with the above model numbers. 1 m type lead wire is only applicable to D-93. ead wire length symbols: 0. m Nil (Example) M9N 1 m M (Example) M9NM Solid state auto switches marked with are produced upon receipt of order. D-P3D is compatible with ø to ø. 3 m (Example) M9N m Z (Example) M9NZ Type, R080 RJ080H R1411 RJ14H R07 RJ07H, R The shock absorber service life is different from that of the cylinder. Refer to Specific Product Precautions for each shock absorber for the replacement period. The shock absorber soft type RJ series type (-X) is a made to order specification. For details, refer to page 9. oad voltage DC V, V V V, V V V, V V V V V, V C 0 V 0 V or less uto switch part no. Perpendicular M9PV 1 M9V 1 9V 93V 90V In-line M9NV M9N M9PV M9P M9V M9 M9NV M9N M9PV M9P M9V M9 M9NV 1 M9N 1 M9P 1 M9 1 P3D 9 93 90 0. (Nil) ead wire length 1 (M) 3 () None (Z) (N) Pre-wired connector pplicable load IC circuit IC circuit IC circuit IC circuit IC circuit Relay, PC Relay, PC 7
Platform Cylinder Series Specifications Fluid ction Proof pressure Maximum operating pressure Minimum operating pressure mbient and fluid temperature Piston speed Cushion ubrication Stroke adjusting range ir Double acting 1. MPa 0.7 MPa Note) 0. MPa to 0 C (No freezing) 0 to 00 mm/s umper (oth ends/standard), Shock absorber (Option) Not required (Non-lube) mm (Extension end, Retraction end: mm each) Note) Maximum operating pressure for this product with the bumper feature. The maximum operating pressure for the cylinder alone is 1 MPa. Shock bsorber Specifications For detailed specifications about shock absorber, /refer to est Pneumatics No. -3. Symbol X138 X777 Made to Order: Individual Specifications (For details, refer to page 71.) Specifications djustable stroke type Fluororubber seals (ctuating cylinder unit only) Made to Order (For details, refer to pages 47 to 14.) Model Shock absorber model Max. energy absorption (J) Stroke absorption Collision speed Max. operating frequency * (cycle/min) mbient temperature Spring force (N) eight (g) Extended Retracted Operating Piston area direction (mm ) IN OUT IN OUT IN OUT IN OUT IN OUT IN OUT R080.94 80 1.9 4. (N) Operating pressure (MPa) 84.8 113 1 1 3 314 378 491 03 804 17 0.3 34 4 0 71 94 113 147 181 41 317 377 0. 4 7 7 1 118 7 189 4 30 8 8 0.7 9 79 141 4 344 4 3 739 880 R07.88 7 R1411 14.7 11 R 8.8 70 0.0 to m/s 4 to 80 C 4..8.8.30 8.34.0 0 It denotes the values at the maximum energy absorption per one cycle. Therefore, the operating frequency can be increased according to the energy absorption. Symbol Specifications The shock absorber service life is different from that of the cylinder depending on the X13 ow speed cylinder ( to 0 mm/s) operating conditions. Refer to the Specific Product Precautions for the replacement period. X Shock absorber soft type RJ series type Theoretical Output OUT IN CX CX CXSJ CXS 713 D- -X
Series eight M () ore size (all bushing bearing) ore size Stroke Stroke 0 7 0 1 0 17 0 0 300 0.8 (0.3) 1.18 (0.0) (kg) 0 7 0 1 0 17 0 0 300 0.7 (0.41) 1.0 (0.7) 0.90 (0.3) 1.4 (0.0).3 (0.8).7 (1.09) 4.1 (.0) 8.8 (3.71) 0.78 (0.4) 1.08 (0.7).00 (1.0).41 (1.) 4. (.) 7.3 (4.31) 1.0 (0.3) 1.39 (0.1).1 (0.87) 3.03 (1.11) 4.9 (.) 8.79 (3.7) 0.8 (0.4) 1.18 (0.8). (1.04).7 (1.8) 4.4 (.30) 7.83 (4.3) 1.13 (0.3) 1.4 (0.).89 (0.88) 3.34 (1.14). (.14) 9.9 (3.79) 0.9 (0.4) 1.7 (0.9). (1.0).77 (1.30) 4.9 (.34) 8.13 (4.39) 1. (0.37) 1.8 (0.3) 3. (0.90) 3. (1.).7 (.17) 9.79 (3.83) 0.98 (0.43) 1.3 (0.0).4 (1.07).9 (1.33) 4.9 (.38) 8.4 (4.43) 3.41 (0.91) 3.89 (1.18).9 (.1).34 (3.87).0 (1.08) 3.08 (1.3).08 (.4) 8.7 (4.47) 3. (0.93) 4. (1.1).31 (.).84 (3.91).7 (1.) 3.4 (1.37). (.4) 9.0 (4.1) Note 1) ( ): Denotes the values of the movable parts weight. (Movable parts weight of a cylinder is included, too.) Note ) The weight indicated above does not include a shock absorber. 3.9 (0.94) 4.43 (1.3).4 (.9) 11.3 (3.9).89 (1.11) 3. (1.39).4 (.0) 9.37 (4.) 4.18 (0.9) 4.70 (1.).99 (.33) 11.87 (3.99) 3.03 (1.13) 3. (1.4).77 (.4) 9.7 (4.9). (1.30) 3.78 (1.4) 7.7 (.41).88 (4.07).1 (.).7 (4.7) (kg).79 (1.34) 8.3 (.49) 13.91 (4.) 4.19 (1.0). (.70).88 (4.74) Series pplicable to Operating Environments that Do Not ccept Copper Copper/Fluorine-free specifications - series For details, refer to the SMC website. 714
Platform Cylinder Series Construction!4! e r t q!1 i w @ @3 #4 @7 M Guide rod/bearing #3 @8 @ @4 Guide rod/bearing @9 @ #!!7!8 u y @0!!3!0 o @1!9 ø ong stroke!1 #1 #0 #4 @ Component Parts Component Parts No. Description Material Note No. Description Material Note 1 Slide block luminum alloy nodized 19 Hexagon socket head cap screw Carbon steel Zinc chromated Plate luminum alloy nodized Grease nipple ø to ø Nickel plating 3 Plate luminum alloy nodized 1 Hexagon socket head cap screw Carbon steel Zinc chromated 4 Guide rod Carbon steel Hard chrome plating Cylinder tube luminum alloy Hard anodized earing alloy 3 Collar luminum alloy nodized all bushing bearing 4 Piston luminum alloy Chromated 7 Type C retaining ring Carbon tool steel Phosphate coating Stainless steel ø to ø Piston rod 8 dapter Carbon steel Electroless nickel plating Carbon steel ø, ø Hard chrome plating 9 Connected disk Carbon steel Electroless nickel plating Type C retaining ring Carbon tool steel Phosphate coating asher Carbon steel Zinc chromated 7 umper Urethane 11 Type C retaining ring Carbon tool steel Phosphate coating 8 umper Urethane Hexagon socket head cap screw Carbon steel Zinc chromated 9 Magnet 13 Spring washer Steel wire Zinc chromated 30 ottom plate luminum alloy nodized 14 djusting bolt (ith bumper) Carbon steel, Urethane Zinc chromated 31 ear ring Resin Nut Carbon steel Zinc chromated Rod seal NR Shock absorber Option 33 Piston seal NR 17 Nut Carbon steel Zinc chromated 34 Tube gasket NR 18 Parallel pin Carbon steel Replacement Parts/Seal Kit Cylinder Model Stroke Standard stroke ong stroke CDQS CQS-PS CQS--PS CDQS CQS-PS CQS--PS Seal kit includes #, #3 and #4. Order the seal kit with the kit number. Since the seal kit does not include a grease pack, order it separately. Grease pack part no.: GR-S-0 ( g) Kit no. CDQS CDQS CQS-PS CQS-PS CQS--PS CQS--PS CDQ CQ-PS CQ--PS CDQ CQ-PS CQ--PS 7 CX CX CXSJ CXS D- -X
Series Dimensions: ø to ø S + Stroke X + Stroke 4 x ød through, counterbore ø depth C ack side 4 x J depth JK 4 x MM Depth M T P T (N) H H HP HG Q ød ød P Y NN E Z P R GP x M x 0.8 R U (N) G G x R (Option) HT HN (Max.) Q + Stroke (N) Cylinder form ø ø Standard stroke,,, 0, 0 8. 7. 9. 9. 8 9. 11 11 C 4.. Slide 18 d all bushing E 9 3 G 7.. 8. 8. GP 0 80 90 H 34 4 4 H. 9 9 HG 14. 18 3 HN 34 39. 44.1 HP 33 39 4 3 HT 18 1 4 8 J M x 0.8 M x 1 M8 x 1. M8 x 1. JK 9. 9. 8 7 8 8 D 4.3..9.9 MM M4 x 0.7 M x 0.8 M x 1 M x 1 M 8 (N) (N) 8 7 8 7 9 0 ong Stroke Stroke range 0, 7, 0 0, 7, 0 7, 0, 1, 0, 17, 0 7, 0, 1, 0, 17, 0, 0, 300 NN M8 x 1.0 M8 x 1.0 M x 1.0 M14 x 1. P 30 4 0 0 P 0 70 0 0 P 80 9 1 130 Q 8 90 Q 4 0 R R080 R080 R07 R1411 R 17. S 9 3 T 13 13 17 17 P dimension is the center sorted factor of the dimension. X Y Z 7. 7. 7. 7. 41 8 8 44 9 9 U 1 77 9 117 7 X 9.. Y 7. 7. 8 9 Z.. 7
Platform Cylinder Series Dimensions: ø, ø (N) S + Stroke X + Stroke 4 x ø8.7 through, counterbore ø14 depth 8 ack side 4 x M x 1. depth T 4 x M8 x 1. Depth P T (N) H HP HG ød M 1. R Z Q P ød E P GP x P (Rc,NPT,G) R G G Y x R F HT (N) Q + Stroke (N) HN (Max.) Standard stroke d Slide all bushing E F G GP H HG HN HP HT (N) (N) P Note) P P P Q, 0, 7, 0. 8 4 7 9. 1. 7. 4 33. 0 14 3 1/8 70 1 0 1, 0, 7, 0 11. 3 31. 130 78 30. 77. 74. 13 1 1/8 90 1 190 9 Q 0 84 ong Stroke R 33 3 S 1 180 T 19 1 7 187 X 33 39. Y. Z 7. 7. P dimension is the center sorted factor of the dimension. Note) Rc, NPT and G ports can be selected. CX CX Stroke range 1, 0, 17, 0, 0, 300 X 4. Y Z 1, 0, 17, 0, 0, 300.. CXSJ CXS D- 717 -X
Series uto Switch Mounting 1 Minimum Stroke for Mounting of uto Switch pplication to No. uto switch of auto model switches mounted 1 1 D-P3D is compatible with ø to ø. pplication uto switch model No. of auto switches mounted 1 D-M9 V D-F7 V D-J79C D-9 V D-7 D-8 D-73C D-80C D-9 D-F7 V D-F7V D-M9 V D-M9 V D-7 H D-80H D-F7 D-J79 D-M9 D-79 D-M9 D-M9 D-F7 D-J79 D-F7 D-F7NT D-F79F D-P3D Proper uto Switch Mounting Position (Detection at stroke end) and Its Mounting Height D-M9 D-M9 D-M9 D-M9 V D-M9 V D-M9 V D-9 D-9 V D-P3D ø ø,, ø, Proper uto Switch Mounting Position/Standard Stroke uto switch D-M9 /M9 V D-M9 D-9 model D-M9 /M9 V D-M9 V D-9 V. 4... 4. 7. 1. 0 1. (4) 4 4 8 0 (4.) 7.. 7. 4. 3. 1. (1) 11 9. 0. 11 9.. 7. 3. ( 1). 9 1 9 3 8 3 ( 0.) 7. 11. 1. 11. 0. 7.. ( 3) 11. Proper uto Switch Mounting Position/ong Stroke uto switch D-M9 /M9 V D-M9 D-9 model D-M9 /M9 V D-M9 V D-9 V 9 11 1 9 11 1 7 (.) 9.. 0. 9.. 1.. 4. ( ) 13 13 4 9 11. ( 7.) 14 18 8 14 18 13. ( 9.)...... 8. 8.. 14. ( ) 8... 14... ( 18) 11. Note 1) ( ): Denotes the values of D-93. Note ) is applicable when mounting D-9, D-M9, D-M9 and D-M9. Note 3) djust the auto switch after confirming the operating conditions in the actual setting. 718 D-P3D 4. 7 D-P3D uto Switch Mounting Height/ Standard Stroke, ong Stroke uto switch D-M9 V model D-M9 V D-M9 V D-9 V D-P3D 19 1 4 9. 17 19. 4. 7 30. 33 3. 39
uto Switch Mounting Series uto Switch Proper Mounting Position (Detection at Stroke End) and Its Mounting Height D-7 D-80 D-73C D-80C D-79 D-7 H D-80H D-F7 D-J79 D-F7 D-J79 D-F7 D-F79F D-F7NT D-F7 V D-J79C D-F7 V D-F7V ø, uto Switch Proper Mounting Position/Standard Stroke uto switch model D-7/7 H D-80H/73C D-80C/F7 /J79 D-73 D-F7 /J79 D-80 D-F7 V/F7 V D-79 D-F7NT D-F79F/J79C D-F7/F7V 9 13 8. 9. 13.. 9.. 3. 14. 18.. 13 uto Switch Proper Mounting Position/ong Stroke uto switch D-7/7 H model D-80H/73C D-80C/F7 /J79 D-73 D-F7 /J79 D-80 D-F7 V/F7 V D-79 D-F79F/J79C D-F7/F7V 9. 13 17. 3. 13. 18 4 7. 1 Operating Range 18. Note ) djust the auto switch after confirming the operating conditions in the actual setting. uto Switch Mounting Height/Standard Stroke, ong Stroke uto switch model uto switch model D-7 D-80 31. 3 D-M9 /M9 V D-M9 /M9 V D-M9 /M9 V D-9 /9 V D-F7 /F7 V D-J79/J79C D-F7 /F7 V D-J79 D-F7/F7V D-F7NT/F79F D-7 /80 D-79 D-P3D D-7 H D-80H D-F7 D-J79 D-F7 D-J79 D-F79F D-F7 D-F7NT. 3 D-73C D-80C 38. 4 D-79 34 37.. 4 7. D-F7 V D-F7 V D-F7V 3 38. Since this is a guideline including hysteresis, not meant to be guaranteed. (ssuming approximately ±30% dispersion) There may be the case it will vary substantially depending on an ambient environment. uto switch mounting brackets Q-0 are not used for sizes over ø of D-9 (V)/M9 (V)/M9 (V)/M9 (V) types. The above values indicate the operating range when mounted with the current auto switch installation groove... 9. 13. 9. 11 14 D-F7NT 3 9 D-J79C 38 41. 719 CX CX CXSJ CXS D- -X
Series uto Switch Mounting uto Switch Mounting racket: Part No. pplicable auto switch D-M9 /M9 V D-M9 /M9 V D-M9 /M9 V D-9 /9 V D-F7 /F7 V/J79/J79C/F7 /J79/F7 V D-F7/F7V/F79F/F7NT D-7 /80/7 H/80H/73C/80C/79 ø to ø ø, ø uto switch mounting bracket part no. Q-0 uto switch mounting bracket fitting parts lineup/eight uto switch fixing screw (M. x ) uto switch mounting screw (M3 x 8) uto switch spacer uto switch mounting nut eight: 3. g Port side D-P3D ø, ø Surfaces with auto switch mounting slot //C side except port side Surfaces with auto switch mounting slot ø ø uto switch mounting surface ø, ø ø, ø C Mounting of auto switch uto switch mounting screw uto switch hen tightening the auto switch mounting screw, use a watchmakers screwdriver with a handle to mm in diameter. Tightening torque for auto switch mounting screw (N m) uto switch model Tightening torque D-M9 (V) D-M9 (V) 0.0 to 0. D-M9 (V) D-9 (V) 0. to 0. qinsert the nut into the auto switch mounting slot on the cylinder tube, and place it in the roughly estimated setting position. with the lower tapered part of the auto switch spacer facing the outside of the cylinder tube, line up the M. through hole with the M. female thread of the auto switch mounting nut. egently screw the auto switch mounting nut fixing screw (M.) into the thread of the auto switch mounting nut through the mounting hole. rengage the ridge on the auto switch mounting arm with the recess in the auto switch spacer. ttighten the auto switch mounting screw (M3) to fix the auto switch. The tightening torque of the M3 screw must be 0.3 to 0.4 N m. yconfirm where the mounting position is, and tighten the auto switch fixing screw (M.) to fix the auto switch mounting nut. The tightening torque of the M. screw must be 0. to 0.3 N m. uthe detection position can be changed under the conditions in step t. uto switch mounting screw (M3 x 0. x 8) uto switch uto switch fixing screw (M. x 0.4 x ) uto switch spacer uto switch mounting nut qinsert the mounting bracket into the mating groove of the cylinder tube. wcheck the detecting position of the auto switch and fix the auto switch firmly with the hexagon socket head cap screw (M. x ). eif the detecting position is changed, go back to step q. Note 1) Ensure that the auto switch is covered with the mating groove to protect the auto switch. Note ) The tightening torque for the hexagon socket head cap screw (M. x ) is 0. to 0.3 N m. Hexagon socket head cap screw (M. x ) (Included with auto switch) Note ) hen shipping cylinders, auto switch mounting brackets and auto switches are shipped together. Other pplicable uto Switches/Refer to pages 1119 to 4 for the detailed specifications of auto switches. uto switch type Model Electrical entry (Fetching direction) Features Reed D-73 D-80 D-73H, 7H D-80H D-F7NV, F7PV, F7V D-F7NV, F7V D-F7V Grommet (Perpendicular) Grommet (In-line) Grommet (Perpendicular) ithout indicator light ithout indicator light Diagnostic indication (-color indicator) ater resistant (-color indicator) Solid state D-F79, F7P, J79 D-F79, F7P, J79 Diagnostic indication (-color indicator) Grommet (In-line) ater resistant D-F7 (-color indicator) D-F7NT ith timer For solid state auto switches, auto switches with a pre-wired connector are also available. Refer to pages 119 and 1193 for details. Normally closed (NC = b contact), solid state auto switch (D-F9G/F9H type) are also available. For details, refer to page 1137. D-7/8/F7/J7 types cannot be mounted on ø to ø. 7 If the cylinder is used in an application in which a magnetic material is placed in close contact around the cylinder as shown in the graph on the below (including cases in which even one of the sides is in close contact) the operation of auto switches could become unstable. Therefore, please check with SMC for this type of application. Magnetic substance (Iron plate, etc.) Magnetic substance (Iron plate, etc.)
Series Made to Order: Individual Specifications Please contact SMC for detailed dimensions, specifications and lead times. 1 djustable Stroke The stroke adjustment range may be expanded with a long adjustment bolt. How to Order Symbol -X138 Standard model no. X138 Specifications Model Stroke adjustment range, mm (Single side 13 mm) djustable stroke, 8 mm (Single side 14 mm) 44 mm (Single side mm) mm (Single side mm) Specifications other than the above are the same as the standard type. Dimensions (Dimensions other than those below are the same as the standard type.) N t Cylinder bore N N t 8. to 1..8 4 7. to..8 4 9. to 3. 37 4.7 4 9. to 3. 39 7.3. to. 49 73. 11. to 31. 49 73. N Fluororubber Seal (Cylinder unit only) Fluororubber is used only for the cylinder unit seal. Symbol -X777 How to Order Standard model no. X777 Fluororubber seal (Cylinder unit only) Specifications Seal material Fluororubber (Cylinder unit only) Specifications other than the above are the same as the standard type. CX CX CXSJ CXS 71 D- -X
Series Specific Product Precautions e sure to read this before handling the products. Refer to back page 0 for Safety Instructions and pages 3 to for ctuator and uto Switch Precautions. Caution Operating Precautions 1. Make sure not to apply to the slide block a load that exceeds the value that has been calculated in the selection procedures.. Operate the cylinder securing it by its plates, not by securing it by its slide block. 3. The clearance between the slide block and the plate at the stroke end is approximately 1 mm to mm. It could be extremely dangerous, as there is the risk of getting your fingers caught. Install a cover as necessary. 4. t both stroke ends, adjust the damper portion at the end of the adjusting bolt so that it comes in contact with the slide block. (The clearance between the slide block and the plate must be 1 mm or more.) If it is operated without making any contact, the piston rod of the actuating cylinder or the connecting hardware (adapter) could become damaged by an excessive impact, or the slide block could collide with the plate and create an abnormal noise.. The load weight or operating speed will be limited if only the adjusting bolt is used. Refer to the section on llowable load when only the adjustment bolt is used on page 711. Please contact SMC if this product will be used in an environment in which the piston rod and the guide shaft surfaces will be exposed to water (hot water), coolant, cutting chips, or dust. 7. The slide block bearings must be greased periodically. Inject grease (Class 1 or lithium soap grease consistency) through the grease inlet. Note) On those with a cylinder bore of ø, apply grease to the guide shaft. 8. To operate the cylinder, use a non-lubricating air supply. Use turbine oil Class 1 (ISO VG), if lubricated. (Using machine oil or spindle oil are not allowed.) Caution Mounting 1. hile a high level of flatness is desired for the surface on which the cylinder is to be mounted, if sufficient flatness cannot be attained, use shims to adjust the installation of the cylinder so that the slide block can operate throughout its stroke under the minimum operating pressure.. Do not scratch or gouge the piston rod of the actuating cylinder, as this could damage the rod seal and lead to air leaks. The same applies to the guide shaft. 3. Make sure not to apply shocks or excessive moment to the slide block of the ball bushing type. 4. The port direction of the actuating cylinder can be changed in 90 increments by removing the four bolts that secure the cylinder in place. fter changing the direction, verify the operation at the minimum operating pressure.. efore the installation, thoroughly flush out the piping to prevent dust or cutting chips from entering the cylinder.. The mounting position of the adjusting bolt and the shock absorber cannot be inverted due to the constraints imposed by the locating pin for the shock absorber that is provided on the slide block. To invert the position, please contact SMC. Handling on Shock bsorber Caution 1. The R series (SMC made) shock absorbers can absorb a wide range of energy without requiring adjustment. (No adjustment screw is provided.). The screw at the bottom is not for adjustment. Never turn this screw as it could cause an oil leak (lowered performance). 3. Do not scratch the surface of the shock absorber rod because doing so could affect the shock absorber s durability or lead to poor retraction. For detailed specifications about the shock absorber, refer to est Pneumatics No. -3. Service ife and Replacement Period of Shock bsorber Caution 1.llowable operating cycle under the specifications set in this catalog is shown below. 1. million cycles R08 million cycles R to R7 Note) Specified service life (suitable replacement period) is the value at room temperature ( to C). The period may vary depending on the temperature and other conditions. In some cases the absorber may need to be replaced before the allowable operating cycle above. 7