SCHMEISER TILL AN PAK HYDRAULIC TRANSPORT KITS ASSEMBLY & PARTS MANUAL

SCHMEISER TILL AN PAK HYDRAULIC TRANSPORT KITS ASSEMBLY & PARTS MANUAL T.G. SCHMEISER CO., INC. P.O. BOX 07 FRESNO, CA. 97 (559) - FAX (559) -79 www.tgschmeiser.com VERSION.a 0-0 COPYRIGHT 0 T.G.SCHMEISER CO., INC.

INTRODUCTION Your Schmeiser Till An Pak Hydraulic Transport Kit is designed to give you many years of dependable service. This manual has been prepared to instruct you in the safe and efficient operation of this machine. Read and study it thoroughly. Follow all instructions carefully. Should your Hydraulic Transport Kit require replacement parts, go to your Schmeiser dealer. Always order genuine Schmeiser replacement parts. If you need information not contained in this manual, contact your Schmeiser dealer. Space has been provided below for you to record the model number of your Till An Pak Hydraulic Transport Kit. Be sure to bring this information with you to your dealer when ordering parts for your Hydraulic Transport Kit. Thank you for buying a Schmeiser Till An Pak Hydraulic Transport Kit. MODEL NUMBER DATE PURCHASED DEALER NAME

TABLE OF CONTENTS Introduction... Table of Contents... Till An Pak Hydraulic Transport Kit Models... Safety Sheet...5 TPP50 Transport Kit Assembly... TPP50 Transport Kit Assembly Instructions...7 TPP50 Transport Kit Assembly... TPP50 Transport Kit Assembly Instructions...9 TPP50 Transport Kit Assembly...0 TPP50 Wheel Axle Bearing Assembly... TPP50 Wheel Axle Hub Assembly... TPP50 Transport Kit Assembly Instructions... TPP50 Transport Kit Assembly...5 TPP50 Linkage Assembly... TPP50 Wheel Leg Assembly...7 TPP50 Transport Kit Assembly Instructions... Hydraulic Transport Kits Hub Assembly...9 TPP550 Transport Kit (Straddle Axle) Assembly...0 TPP550 Wheel Axle Assembly... TPP550 Heavy Duty Wheel Axle Assembly... TPP550 Transport Kit Assembly Instructions... Limited Warranty...5 Maintenance and Repair Record... Notes...7

SCHMEISER HYDRAULIC TRANSPORT KIT MODELS TPP50 TILL AN PAKS -0 TO 0-0 TPP50 TILL AN PAKS -0 TO -0 TPP50 TILL AN PAKS -0 TO -0 TPP50 TILL AN PAKS -0 TO -0 TPP50HD TILL AN PAKS -0 TO -0 TPP550 STRADDLE AXLE - -0 TO 0-0

SAFETY The safe operation of any machinery is an important concern to farmers and manufactures. There are obvious and hidden potential hazards involved in the operation of this implement. Carefully read and follow all safety precautions before operation. Serious injury or death may occur unless care is taken to insure the safety of both the operator and any other persons in the area.. Never permit anyone to ride on or walk beside the implement when moving.. Never permit anyone to ride on tractor when implement is being moved.. When performing operating functions, never allow anyone to be near the implement or the tractor.. Do not enter tractor when tractor is moving. Avoid serious injury or death from contact with rotating tires. Enter and exit the tractor only when it is completely stopped. 5. Be sure of water, gas, sewer, or electric line locations before operating implement.. When in transport, use accessory lights and devices for adequate warning to operators of other vehicles. Comply with all Federal, State and local laws when traveling on public roads. 7. Use Slow Moving Vehicle emblem for warning vehicles approaching from the rear.. When transporting, remember that the implement may be wider than your tractor and extreme care must be taken to allow for safe clearance. 9. Never allow inexperienced or untrained personnel to operate the implement or tractor without supervision. 0. When using compressed air to clean implement, wear safety glasses.. Check all fasteners for tightness or damage before and after operation. Repair immediately if required.. Store implement in a stable position. Insure that safety equipment (lockouts, stands, pins, etc.) is secure and in place before detaching from tractor. 5

S C H M IN E I IN S E R T. G. SCHMEISER CO., INC. TPP 50 ASSEMBLY 9 5 SERIAL PLATE MANUAL CANISTER 7 9 5 7 TILL AN' PAK BEARING TILL AN' PAK FRAME TILL AN' PAK ROLLER 0 TILL AN' PAK TONGUE Ref No. Part No. Description Qty..... 5.. 7.. 9. 0..... 5.. 7.. 9. HT-00A000L(R) HT-00C00 HT-00B000 GHC-00T FMB 90 GWD-LB HT-(00)C000 GWT-5LBH GWT-750 TPP00 HT-00B007 HT-00A007 CSNC500 LWASHER-0 HXNUT-0NC CSNC5009 CSNC500 LWASHER-0 HXNUT-0NC PMCK-000 End Mount Weldment LH (RH) Wheel Axle Bearing - UHMW Center Frame Weldment " X " Tie Rod Hydraulic Cylinder /" X /" 90-degree Adapters Lockout Bar for " X " Hyd. Cylinder Wheel Axle Weldment (specify size) 5" X " Wheel (See p.9 for Hub Assembly) 7." X 5" Tire with Wheel (Optional) -/" X " Tongue Pin Weldment Center Frame Front Clamp Plate End Mount Bottom Clamp Plate 5/" X 5-/" Gr.5 NC Cap Screw 5/" Lock Washer 5/" NC Hex Nut 5/" X -/" Gr.5 NC Cap Screw /" X " Gr.5 NC Cap Screw /" Lock Washer /" NC Hex Nut Seal Kit for " X " Hyd. Cylinder 0 0 (559) - Fax (559) -79 www.tgschmeiser.com

T. G. SCHMEISER CO., INC. TPP 50 ASSEMBLY INSTRUCTIONS. Lay Till An' Pak Frame on ground.. Unbolt Till An' Pak Frame from Pillow Block Bearings on Roller. Leave Roller attached to Pillow Block Bearings.. Position each End Mount () between Till An' Pak Frame and Pillow Block Bearing (9). - Refer to the drawing for positioning.. Place Wheel Axle (7) with Plastic Bushings () between End Mounts ().The Cylinder anchor on the Wheel Axle should be facing in the upward position. 5. Bring in End Mounts () and install and tighten all fasteners. - Use () /" x " Bolts to fasten Pillow Block Bearing, End Mount, and Till An' Pak Frame. - Use () 5/" x " Bolts to attach End Mount to Bottom Clamp Plate ().. Remove Tongue Pin from Till An' Pak Frame. It is located at the base of the Frame tongue guide. 7. Position Center Frame () on the tongue guide of the Till An' Pak frame. The two ears at the bottom of the center bracket should slide over the tongue guide pin hole of the Till An' Pak frame. The cylinder anchor portion of the Center Frame should be facing upward at a 5-degree angle aimed toward the rear of the unit. Refer to the drawing for the positioning.. Place -/" x -/" Tongue Pin in the tongue guide hole. Remember, the tongue, the Center Frame and the tongue guide hole on the frame all have to line up in order to properly install the tongue pin. - Use () 5/" x 5-/" Bolts to attach Center Frame to Front Clamp Plate. 9. Attach " x " Tie Rod Hydraulic Cylinder () to Center Frame and Wheel Axle. The rod clevis of the cylinder should attach to the wheel axle cylinder anchor. 0. Install Cylinder Lockout Bar (). See drawing for proper installation.. Install tires on the wheel axle. (559) - Fax (559) -79 www.tgschmeiser.com 7

S C H M I S E T. G. SCHMEISER CO., INC. TPP 50 ASSEMBLY 5 7 7 9 0 5 9 0 E R IN IN Ref No. Part No. Description. HT-00A000L(R) Till An' Pak Mount Weldment LH or RH. HT-00A007 Bracket Mounting Clamp. HT-00B000L(R) Tire Axle Leg Weldment LH or RH. HT-00B00 Lockout Plate 5. GWT-5LBH 5 X Wheel Rim (See p.9 for Hub Assembly) GWT-750 7. X 5 Tire with Wheel (Optional). GHC-500T -/" X " Tie Rod Hyd. Cylinder 7. FMB 90 /" M - /" 90 Fitting. CSNC5009 5/" X " NC Cap Screw Gr.5 0 9. LWASHER-0 5/" Lock Washer 0 0. HXNUT-0NC 5/" NC Hex Nut 0. CSNC09 -/" X " NC Cap Screw Gr.. LWASHER- -/" Lock Washer. HXNUT-NC -/" NC Hex Nut. GPN-X00 /" X -/" Clevis Pin 5. GPN-00LYN /" Lynch Pin. GPN-5HC " X -/" Cylinder Pin 7. GPN-0CLIP 5/" Wire Dia. Hair Pin Clip. CSNC500 /" X " Gr.5 Cap Screw 9. LWASHER-0 /" Lock Washer 0. HXNUT-0NC /" NC Hex Nut. FWASHER-0 /" Flat Washer (559) - Fax (559) -79 www.tgschmeiser.com Qty.

T. G. SCHMEISER CO., INC. TPP 50 COMPLETE ASSEMBLY 0 0 7 9 5 SERIAL PLATE MANUAL CANISTER 5 5 9 7 ROLLER TILL AN' PAK FRAME 5 TILL AN' PAK TONGUE (559) - Fax (559) -79 www.tgschmeiser.com 0

T. G. SCHMEISER CO., INC. TPP 50 COMPLETE ASSEMBLY Ref No. Part No. Description Qty.. HT-00B000L(R) End Bracket Weldment LH (RH). HT-00B005 End Bracket to Frame Clamp Plate. HT-00B00 End Bracket to Cross Bar Clamp Plate. HT-00A000 Center Bracket 5. HT-00A007 Center Bracket to Frame Clamp Plate. HT-00A00 Center Bracket to Cross Bar Clamp Plate 7. HT-(00)D000 Main Bar Weldment (specify size). HT-00C000 Wheel Axle Weldment 9. GWT-5LBH GWT-750 5 X Wheel (see p.9 for Hub Assembly) 7. X 5 Tire with Wheel (Optional) 0. SLL5 Wheel Axle Bearing Assembly (See p. for details). GHC-500T -/" x 0" Tie Rod Hydraulic Cyl.. FMB 90 /" X /" 90-degree Adapters. PMCK-500 Seal Kit for -/" x 0" Hyd. Cylinder. CSNC5009 5/" X " Gr.5 NC Cap Screw 5. LWASHER-0 5/" Lock Washer. HXNUT-0NC 5/" NC Hex Nut 7. CSNC500 CSNC500 /" X " Gr.5 NC Cap Screw (5 ft. and under) 5/" X " Gr.5 NC Cap Screw ( ft. and up). LWASHER-0 /" Lock Washer (5 ft. and under) LWASHER-0 5/" Lock Washer ( ft. and up) 9. HXNUT-0NC /" NC Hex Nut (5 ft. and under) HXNUT-0NC 5/" NC Hex Nut ( ft. and up) 0..... CSNC50 /" X 7-/" Gr.5 NC Cap Screw LWASHER- /" Lock Washer HXNUT-NC /" NC Hex Nut CSNC500 /" X 5" Gr.5 NC Cap Screw GPN-X0 -/" X -/" Pin Weldment (559) - Fax (559) -79 www.tgschmeiser.com

T. G. SCHMEISER CO., INC. WHEEL AXLE BEARING ASSEMBLY 5 NOTE: - Ensure equal amount of space on each side before tightening U-Bolt. - Ensure equal number of threads on each side of U-Bolt. Ref No.. Part No. SLL 5 Description Bearing Cradle Cap Weldment Qty.. SLL 50 Bearing Cap Casting Machined. UBNCR " Bearing U-bolt. HXNUT-NC " NC Hex Nut 5. LWASHER- " Lock Washer SLL 5 SLL 5 U-Bolt Assembly (includes items,, and 5) Axle Bearing Assembly (includes items,,,, and 5) (559) - Fax (559) -79 www.tgschmeiser.com

T. G. SCHMEISER CO., INC. TPP50 HYDRAULIC TRANSPORT KIT HUB ASS'Y 7 5 5 7 9 0 Ref No. Part No. GHB-XORC GHB-XOCN GSP-SPWA GSP-CANT GPN-0X0C GHB-XCAP GWT-5LBH GWT-750 CSNC50705 LWASHER-07 HXNUT-07NC SSNCS0X Description. HT-00C00 " x " Removable Single Ended Spindle TBU-0G0 " x 0-/" Removable Double Ended Spindle. GHB-XGSL Grease Seal. WHB-0X0 /" x " UNF Wheel Bolts for on Std. Hub. GHB-XICN Inner Bearing Cone for on Std. Hub 5. GHB-XIRC Inner Bearing Cup for on Std. Hub. GHB-XSTD Standard on Hub Assembly Complete (includes items,,, 5, 7,, ) 7.. 9. 0..... 5.. 7. Outer Bearing Cup for on Std. Hub Outer Bearing Cone for on Std. Hub Spindle Washer Spindle Castle Nut /" x " Cotter Pin Hub Cap 5 x Wheel - Standard 7. x 5 Ply Tire with Wheel - Optional 7/" x -/" Gr.5 NC Cap Screw 7/" Lock Washer 7/" NC Hex Nut /" x " Set Screw Quantity -Wheel Option -Wheel Option - - (559) - Fax (559) -79 www.tgschmeiser.com

T. G. SCHMEISER CO., INC. TPP 50 ASSEMBLY INSTRUCTIONS. Lay Till An' Pak Frame on ground.. Unbolt Till An' Pak Frame from Pillow Block Bearings on Roller. Do not remove Pillow Block Bearings from Roller.. Position each End Bracket () between Till An' Pak Frame and Pillow Block Bearing. - Be sure that the angle iron leg of the End Bracket points inward. Refer to the drawing for positioning. - Use () /" x " or () 5/" x " Bolts to fasten Pillow Block Bearing, End Bracket, and Till An' Pak Frame. - Use () 5/" x " Bolts to attach End Bracket - Roller Frame Mount Plate. All fasteners - hand tighten only!. Remove Tongue Pin from Till An' Pak Frame. It is located at the base of the Frame tongue guide. 5. Position Center Bracket () on the tongue guide of the Till An' Pak frame. The two ears at the bottom of the center bracket should slide over the tongue guide pin hole of the Till An' Pak frame. The cylinder anchor portion of the Center Bracket should be facing upward at a 5-degree angle aimed toward the rear of the unit. Refer to the drawing for the positioning. - Place -/" x -/" Tongue Pin in the tongue guide hole. Remember, the tongue, the Center Bracket and the tongue guide hole on the frame all have to line up in order to properly install the tongue pin. - Use () 5/" x " Bolts to attach Center Bracket - Roller Frame Mount Plate. All fasteners - hand tighten only!. Position Main Cross Bar (7) on top of the End Bracket. The bar should be placed between the two holes on the topside of the End Bracket. The truss strap should be positioned on the top and the two sets of the Bearing Mount Plates welded on the Main Cross Bar should be placed to the back side of the machine. - Use () /" x 5" Bolts to attach Center Bracket - Main Cross Bar Mount Plate. - Use () /" x 7-/" Bolts to attach Main Cross Bar - End Bracket Mount Plate. All fasteners - hand tighten only! 7. Attach Wheel Axle () to Main Cross Bar (7) using the Bearing Assemblies. The Cylinder anchor on the Wheel Axle should be facing in the upward position.. Attach -/" x 0" Hydraulic Cylinder () to Center Bracket and Wheel Axle. The rod clevis of the cylinder should attach to the wheel axle cylinder anchor. 9. Securely tighten all fasteners. (559) - Fax (559) -79 www.tgschmeiser.com

T. G. SCHMEISER CO., INC. TPP 50 ASSEMBLY -CYLINDER UNIT -CYLINDER UNIT (HEAVY DUTY) 7 5 Ref No. Part No. Description Qty.. HT-00A00 Pull Frame for -Cyl. Units. HT-(00)B00 Main Frame for -Cyl. Units (specify size). HT-00A00 Pull Frame Pin. HT-00D000L Axle Leg with Hub, Left 5. HT-00D000R Axle Leg with Hub, Right. HT-00A00 Pull Frame for -Cyl. Units 7. HT-(00)B00 Main Frame for -Cyl. Units (specify size). GPN-0CA0 -/" X 5-/" Pin or (559) - Fax (559) -79 www.tgschmeiser.com 5

S C I S T. G. SCHMEISER CO., INC. TPP 50 LINKAGE ASSEMBLY 5 7 7 0 0 9 E R PULL FRAME 0 MAIN FRAME IN IN TILL AN' PAK ROLLER Ref No. Part No. Description Qty. -Cyl. -Cyl..... 5.. 7. GHC-00T HT-00C00 HT-00C000 GWD-LB FMB 90 HT-00A00 GPN-00LYN " X " Tie Rod Hydraulic Cylinder Hydraulic Cylinder Linkage Pivot Plate Hydraulic Cylinder Linkage Weldment Lockout Bar for " X " Hydraulic Cylinder /" X /" 90 degree Adapters Pull Frame Pin /" Lynch Pin. PMCK-000 Seal Kit for " X " Hydraulic Cylinder 9. GPN-HC " X " Cylinder Pin 0.. GPN-0X0C GPN-X0 /" Cotter Pin " X -/" Std. Clevis Pin (red). GPN-X00 " X -/" Std. Clevis Pin. GPN-05SL /" X -/" Lockout Bar Pin (559) - Fax (559) -79 www.tgschmeiser.com

T. G. SCHMEISER CO., INC. TPP 50 WHEEL LEG ASSEMBLY 5 7 0 9 Ref No. Part No. Description Qty. per Leg.... 5.. 7.. 9. 0.. HT-00D000 HT-00C00 GHB-XSTD Wheel Axle Leg " x " Single Ended Removable Spindle on Hub Complete (see p.9 for Hub Assembly) UBNC0XT 5/" NC Tri Bend U-Bolt HXNUT-0 5/" NC Hex Nut LWASHER-0 5/" Lock Washer HT-00D00 Wheel Axle Leg Spacer SSNCS0X /" X " NC Set Screw CSNC50705 7/" X -/" NC Cap Screw LWASHER-07 7/" Lock Washer HXNUT-07NC 7/" NC Hex Nut (559) - Fax (559) -79 www.tgschmeiser.com 7

T. G. SCHMEISER CO., INC. TPP 50 ASSEMBLY INSTRUCTIONS. Lay Till An' Pak Roller on ground. Position Main Frame over Roller and bolt frame to Pillow Block Bearings. - Use () /" x -/" Gr.5 NC Bolts ( ft. to ft. units) or 5/" x -/" Gr.5 NC bolts (9 ft. & up units.). Position Wheel Leg between the bottom cross bars and top cross bar with wheel facing outward (saddle mounting plates on bottom of wheel axle should face downward.). Place saddle pads under wheel axle on two bottom cross bars (see Wheel Leg Assembly drawing on page ).. Position Wheel Leg to desired distance from side end of unit (spacing of wheel is based upon customer's needs.) 5. Position third saddle between top cross bar and Wheel Leg. Tilt Wheel Leg and place into position (use of a mallet hammer may be necessary.). Fasten Wheel Leg with two Tri-Bend U-Bolts on each mount. Same procedure is required for center Wheel Leg (wheels face inward, opposite direction of end wheels.) 7. Mount tires to Wheel Legs and tighten (Tires are optional).. Fasten outer set of ears of Pull Frame to the Main Frame (-/" x 5-/" yellow Pin and /" Cotter Pin.) After fastening be sure to grease both zerk holes (see Assembly drawing on page.) 9. Position Pivot Plate between Main Frame center ears and fasten with -/" x 5-/" yellow Clevis Pin (refer to the drawing on page 5 for proper positioning). 0. Slide Pull Frame in front of Main Frame. Position -/" x -/" Tongue Pin in Pull Frame tongue hole.. Position Hydraulic Cylinder with rod facing toward rear of unit. Align holes with Pivot Plate and lockout bar (elevation of Pull Frame may be necessary.) - Use " x -/" Red Clevis Pin with /" Lynch Pn.. Remove plugs from cylinder before extending.. Thread in place () 90-degree adapters into cylinder.. Check tightness of all bolts and make sure all pins are in place. (559) - Fax (559) -79 www.tgschmeiser.com

T. G. SCHMEISER CO., INC. HYDRAULIC TRANSPORT KITS HUB ASSEMBLY 5 7 9 0 Ref No. Part No. Description. GHB-XSTD Standard on Hub Assembly Complete (includes items,,, 5, 7,, ) Quantity per spindle TPP50 TPP50. GSP-7S " x " Single Ended Spindle. GHB-XGSL Grease Seal. WHB-0X0 /" x " UNF Wheel Bolts for on Std. Hub. GHB-XICN Inner Bearing Cone for on Std. Hub 5. GHB-XIRC Inner Bearing Cup for on Std. Hub 7.. 9. 0.... GHB-XORC Outer Bearing Cup for on Std. Hub GHB-XOCN Outer Bearing Cone for on Std. Hub GSP-SPWA GSP-CANT GPN-0X0C GHB-XCAP GWT-5LBH Spindle Washer Spindle Castle Nut /" x " Cotter Pin Hub Cap 5 X Wheel - Standard GWT-750 7. x 5 Ply Tire with Wheel - Optional (559) - Fax (559) -79 www.tgschmeiser.com 9

T. G. SCHMEISER CO., INC. TPP 550 COMPLETE ASSEMBLY 5 5 5 7 0 9 5 7 TILL AN' PAK RING ROLLER (559) - Fax (559) -79 www.tgschmeiser.com 0

T. G. SCHMEISER CO., INC. TPP 550 COMPLETE ASSEMBLY Ref No. Part No. Description Qty.. TSA-(00)A000 Straddle Axle Main Frame Weldment (specify size). TSA-00C000 Wheel Axle Weldment TSA-00C00 Heavy Duty Wheel Axle Weldment. TSA-(00)D000 Pull Frame Assembly (specify size). GPN-L " X 7" General Lock Pin Weldment 5. GPN-00LYN /" Lynch Pin. TSA-00E000 Straddle Axle Tongue Weldment 7. TSA-00G000 Straddle Axle Ratchet Weldment. GPN-X0 " X " Standard Clevis Pin Weldment 9. TSA-00F00 Straddle Axle Tongue Pin 0. GHC-00T " X " Tie Rod Hydraulic Cylinder. GWD-LB Lockout Bar for " X " Hydraulic Cylinder SA. GPN-05SL /" X -/" Swivel Lock Pin. CSNC " X 9" Gr. NC Cap Screw. NYNUT-NC " NC Hex Nylon Lock Nut 5. CSNC5 " X " Gr.5 NC Cap Screw. FTP-00C000 FTP Pull Frame Hitch Clevis Weldment 7. PMCK-000 Seal Kit for " X " Hydraulic Cylinder (559) - Fax (559) -79 www.tgschmeiser.com

T. G. SCHMEISER CO., INC. TPP550 WHEEL AXLE ASSEMBLY 7 5 9 0 Ref No..... 5.. 7.. 9. 0.... Part No. TSA-00C000 TSA-00B000 GHB-XGSL WHB-0X0 GSP-SPWA Description Wheel Axle Weldment Wheel Axle Bearing Weldment Grease Seal /" x " UNF Wheel Bolts for on Std. Hub GHB-XICN Inner Bearing Cone for on Std. Hub GHB-XIRC Inner Bearing Cup for on Std. Hub GHB-XSTD Standard on Hub Assembly Complete (includes items,, 5,,, 9, ) GHB-XORC Outer Bearing Cup for on Std. Hub GHB-XOCN Outer Bearing Cone for on Std. Hub GSP-CANT GPN-0XC GHB-XCAP Spindle Washer Spindle Castle Nut /" x " Cotter Pin Hub Cap. GWT-9550 9.5 x 5 Ply Tire with Wheel Qty. (559) - Fax (559) -79 www.tgschmeiser.com

T. G. SCHMEISER CO., INC. TPP550 HEAVY DUTY WHEEL AXLE ASS'Y 7 5 9 0 Ref No..... 5.. 7.. 9. 0.... Part No. TSA-00C00 TSA-00B000 GHB-XGSL WHB-09X0 GSP-SPWA Description Heavy Duty Wheel Axle Weldment Wheel Axle Bearing Weldment Grease Seal Wheel Bolts for on Heavy Hub GHB-XICN Inner Bearing Cone for on Heavy Hub GHB-XIRC Inner Bearing Cup for on Heavy Hub GHB-XHVY Heavy on Hub Assembly Complete (includes items,, 5,,, 9, ) GHB-XORC Outer Bearing Cup for on Heavy Hub GHB-XOCN Outer Bearing Cone for on Heavy Hub GSP-CANT GPN-0XC GHB-XCAP 7/" Spindle Flat Washer 7/" NF Spindle Castle Nut /" x " Cotter Pin Hub Cap. GWT-.5 x Ply Tire with Wheel Qty. (559) - Fax (559) -79 www.tgschmeiser.com

T. G. SCHMEISER CO., INC. TPP 550 ASSEMBLY INSTRUCTIONS. Lay Till An' Pak Roller on ground. Install flange bearings of ring roller shafts.. Position Main Frame over Roller and bolt frame and roller to flange bearings. - Use () 5/" x -/" Gr.5 NC bolts with lock washers and hex nuts.. Install Wheel Axle to Main Frame. Tighten wheel axle bearings onto main frame bearing mounts. - Use /" x " Gr.5 NC bolts with lock washers and hex nuts.. Install tire and wheel assemblies onto hubs on the wheel axle. Refer to page (standard duty) or (heavy duty) for details. 5. Mount Pull Frame large brace (with clevis attached) to the main frame, then mount secondary brace to the main frame. - Use " x " Gr.5 NC bolts with nylon lock nuts. Connect to each other for field use with lock pin. See drawing on page 0 for reference. For transport, remove lock pin and swing both braces forward onto storage plate and secure with same lock pin.. Install transport tongue. Fasten with " x 9" Gr. NC bolt and " nylon lock hex nut. 7. Install Ratchet weldment. Bushing side - to the tongue, clevis side - to main frame. - Use " x " standard clevis pin with lynch pin on tongue side and cylinder pin with cotter pins on main frame side.. Mount " x " Hydraulic cylinder to Main Frame and then to Wheel Axle. Install Lockout Bar. Refer to assembly drawing on page 0 for details. 9. Install Jack Stand to front of Main Frame. (559) - Fax (559) -79 www.tgschmeiser.com

T.G. SCHMEISER CO., INC. Limited Warranty Statement T. G. Schmeiser Co., Inc. warrants each new Schmeiser product to be free from defects in material and workmanship. This warranty is applicable only for the normal service life expectancy of the product or components, not to exceed twelve () consecutive months from the date of delivery of the new Schmeiser product to the original purchaser. Genuine T. G. Schmeiser Co., Inc. replacement parts and components will be warranted for 90 days from date of purchase, or the remainder of the original equipment warranty period, whichever is longer. Under no circumstances will it cover any merchandise or components thereof, which, in the opinion of the company, has been subjected to misuse, unauthorized modifications, alteration, an accident or if repairs have been made with parts other than those obtainable through T. G. Schmeiser Co., Inc. The Company in no way warrants engines, batteries, cylinders, tires or other trade accessories since these items are warranted separately by their respective manufacturer. Expendable components such as points, shanks, blades, rings, bearings, teeth, and the like are excluded from this warranty. Our obligation under this warranty shall be limited to repairing or replacing, free of charge to the original purchaser, any part that, in our judgment, shall show evidence of such defect, provided further that such part shall be returned within thirty (0) days from date of failure to T. G. Schmeiser Co., Inc., routed through the dealer and distributor from whom the purchase was made, transportation charges prepaid. This warranty shall not be interpreted to render T. G. Schmeiser Co., Inc. liable for injury or damages of any kind or nature to person or property. This warranty does not extend to the loss of crops, loss because of delay in harvesting, or any expense or loss incurred for labor, substitute machinery, rental or for any other reason. Except as set forth above, T. G. Schmeiser Co., Inc. shall have no obligation or liability of any kind on account of any of its equipment and shall not be liable for special or consequential damages. T. G. Schmeiser Co., Inc. makes no other warranty, expressed or implied, and, specifically, T. G. Schmeiser Co., Inc. disclaims any implied warranty or merchantability or fitness for a particular purpose. Some states or provinces do not permit limitations or exclusions of implied warranties or incidental or consequential damages, so the limitations or exclusion in this warranty may not apply. This warranty is subject to any existing conditions of supply, which may directly affect our ability to obtain materials or manufacture replacement parts. T. G. Schmeiser Co., Inc. reserves the right to make improvements in design or changes in specifications at any time, without incurring any obligation to owners of units previously sold. No one is authorized to alter, modify or enlarge this warranty nor the exclusion, limitations and reservations. WARRANTY VOID IF NOT REGISTERED WITHIN 0 DAYS OF PURCHASE DATE 5

Schmeiser Till An' Pak Hydraulic Transport Kit Maintenance & Repair Record Date of Service or Repair Performed Parts Service Replaced

Notes 7

Notes