MAG-BEECO deliver the highest level of performance, reliability, ease of use and save time and money. BENEFITS Peace of Mind MAG-BEECO Backflow valves pass the most rigorous, stringent test standards and are designed with safety in mind. You won t be kept awake at night wondering if your backflow valve is doing its job. Savings on maintenance and commissioning MAG-BEECO s Modular Body construction means you can instantly convert from a Double Check to a Reduced Pressure Zone. Maintenance is easy as repair parts are modular: it only takes two relief valve kits and three check repair kits to cover all sizes. This means you don t need an unmanageable and costly array of parts making BEECO valves not only the easiest valves to service, but maintenance contracts will be cheaper. And your scheduling service won t be delayed either. Easy valve access MAG-BEECO covers for both our epoxy coated ductile iron and brass products are easily accessible. A single bolt enables you to remove the brass cover. On our large ductile iron products, we have eliminated the numerous bolts of other products and replaced them with a simple pipe coupling that is not under pressure. The valve can be exposed within minutes again saving time and money. Easily replaceable Check Valves Once you have accessed the valve with our easily removable covers, we have also solved the problem of broken checks with our easily replaceable checks. No more frustration, wastage and extra cost of checks being broken while prying them out for repair. A simple pair of pliers enables you to grab a well-designed, innovative metal nipple and just snap the part out with ease. AS/NZS 2845.1 Lic: WM 74542
Fire Detector Check Valves APPLICATIONS For installation on potable water lines Protects against back siphonage and back pressure Maximum protection in Low Hazard conditions (Single Detector Check Valve) and in Medium Hazard conditions (Double Detector Check Valve) in fire sprinkler systems Metered by-pass to detect unauthorised water use and leaks Single Detector Check Valve with Metered By-Pass Flanged or Roll Grooved Product Code Description Length of Device (mm) SDC80YV 80mm SDC with 20mm Metered By-Pass 470 SDC100YV 100mm SDC with 25mm Metered By-Pass 470 SDC150YV 150mm SDC with 25mm Metered By-Pass 578 SDC200YV 200mm SDC with 25mm Metered By-Pass 851 Single Detector Check Valve with Spacer By-Pass Flanged or Roll Grooved Product Code Description Length of Device (mm) SDC80SE/CW 80mm SDC with 20mm Spacer By-Pass 470 SDC100SE/CW 100mm SDC with 25mm Spacer By-Pass 470 SDC150SE/CW 150mm SDC with 25mm Spacer By-Pass 578 SDC200SE/CW 200mm SDC with 25mm Spacer By-Pass 851 Single Testable Check Valve Flanged or Roll Grooved Product Code Description Length of Device (mm) STCV80 80mm STCV Testable with Test Points 470 STCV100 100mm STCV Testable with Test Points 470 STCV150 150mm STCV Testable with Test Points 578 STCV200 200mm STCV Testable with Test Points 851 Double Detector Check Valve with Metered By-Pass Flanged or Roll Grooved Product Code Description Length of Device (mm) DDCV65/20 65mm DDCV with 20mm Metered By-Pass 470 DDCV80/20 80mm DDCV with 20mm Metered By-Pass 470 DDCV100/20 100mm DDCV with 20mm Metered By-Pass 470 DDCV150/20 150mm DDCV with 20mm Metered By-Pass 578
AS/NZS 2845.1 Lic: WM 74542 FEATURES AND BENEFITS Single Detector Check Valve: 80mm-200mm size options available with 20mm and 25mm metered or spacer by-pass Double Detector Check Valve: 65mm-150mm size options with 20mm metered by-pass Shorter lay lengths Fewer parts needed save money Servicing ability and commissioning is easy, simple and cost effective Entire valve can be fully serviced inline lightweight short lay length modular design makes this valve easy and quick to service Pipe Connections: Flanged and Grooved connections Epoxy coated ductile iron construction Ease of access means lower maintenance costs saving time and money Noryl Replacement check valves 300 series stainless steel springs Max. working pressure: 1200 kpa Max. working temperature: 60 C Hydrostatic Test Pressure: 2400 kpa INSTALLATION Install device as per AS3500 and any local applicable codes and manufacturer s instructions. SPECIFICATION SAMPLE The MAG-BEECO Single/Double Detector Check Valve backflow preventer shall be WaterMark approved rated at le Detector 60 C. Check The main Valve body Specification shall be epoxy Sheet coated ductile iron construction with Noryl replaceable check valves. del SDC (3-8 ) The Single/Double Detector Check Valve shall be MAG-BEECO. Flomatic Corporation FLOW CHARACTERISTICS P R E S S U R E L O S S kpa M/W C psi 69 7 10 55 5.6 8 42 4.2 6 28 2.8 4 FLOW CURVES 3" (80mm) 4" (100mm) 6" (150mm) 14 1.4 2 TYPICAL INSTALLATION 0 350 700 1050 1400 1750 2100 gpm 79.49 158.97 238.45 317.94 397.43 476.91 M /H 22.08 44.17 66.26 88.34 110.43 132.51 lps FLOW RATE 3 DC Single Detector Check Valve Backflow ters should be installed with adequate clearance sy accessibility for testing and maintenance and protected from freezing. Local codes shall installation requirements. Unless otherwise d, the assembly shall be mounted at a minimum ce of 12 (305mm) between port and floor or The assembly shall have a maximum of 30 ) above adequate drains with sufficient side ce for testing and maintenance. The installation made so that no part of the unit can be ged. Thermal water expansion can cause ive pressure. Excessive pressure situations be eliminated to avoid possible damage to the Capacity thru Schedule 40 Pipe (GPM) Pipe size 5 ft/sec 7.5 ft/sec 10 ft/sec 15 ft/sec 2 ½ 75 112 149 224 3 115 173 230 346 4 198 298 397 595 6 450 675 900 1351 8 780 1169 1559 2339 Design is for illustrative purposes.
In Wall Backflow Tundish - Single or Dual Assembly MAG purpose made tundishes with Beeco s Reduced Pressure Zone Backflow Device for maximum protection in high hazard applications. Single or Dual configurations in Stainless Steel Cabinets. APPLICATIONS For installation on potable water lines Protects against back siphonage and back pressure Maximum protection in High Hazard applications Configuration: Single or Dual Suitable for hot and cold water FEATURES AND BENEFITS Cover available as either lockable Perspex front cover with key lock or solid stainless steel cover Cabinet: Stainless Steel Fully assembled, pre-plumbed with RPZD Body, Barrel Unions, Y Strainer and Ball Valves Sizes: 15mm to 50mm single and dual assemblies (above 32mm is custom built enclosure) RPZs fully serviceable inline Test points from top of backflow device Noryl Replacement check valves Maximum working pressure: 1200 kpa Maximum working temperature: 82 C Hydrostatic test pressure: 2400kPa INSTALLATION Unless otherwise specified, install device at a minimum of 300mm above adequate drain with sufficient clearance for testing and maintenance. Note: Illustrated dimensions apply only to 15mm, 20mm and 25mm assemblies. SPECIFICATION SAMPLE The Backflow in Wall Tundish assembly shall be WaterMark approved rated at 82 C. The Tundish cabinet shall be stainless steel. The main RPZs shall be all brass construction with easily replaceable check valves. The assembly shall be MAG-BEECO. Figure 1- Flow Rates FRP-0.50LF, FRP0.75LF and FRP1.00LF
AS/NZS 2845.1 Lic: WM 74542 Product Code / Model Dual RPZ Assembly Product Code / Model Single RPZ Assembly MAG/IBT15/D 15mm Dual hot and cold MAG/IBT15/S 15mm Single hot and cold MAG/IBT20/D 20mm Dual hot and cold MAG/IBT20/S 20mm Single hot and cold MAG/IBT25/D 25mm Dual hot and cold MAG/IBT25/S 25mm Single hot and cold MAG/IBT32/D 32mm Dual hot and cold MAG/IBT32/S 32mm Single hot and cold MAG/IBT40/D 40mm Dual hot and cold MAG/IBT40/S 40mm Single hot and cold MAG/IBT50/D 50mm Dual hot and cold MAG/IBT50/S 50mm Single hot and cold MAG BACKFLOW INWALL CABINET With Hot & Cold RPZ Valves ISOLATION VALVE TEST COCKS ISOLATION VALVE WATER INLET WATER OUTLET ISOLATION VALVE WATER INLET 900 WATER OUTLET TEST COCKS ISOLATION VALVE Y STRAINER 90 Note: - Pre plumbed - Clear Lockable Viewing Panel - Full Stainless Steel Panel Available - Sizes available: 15-32mm (above 32mm is custom built enclosure) - Pressure loss: 49kPa - Depth: 90mm 100 430 65
Reduced Pressure Zone Device (RPZs) - 15mm-50mm Testable High Hazard Designed with ease of access in mind and with very few spare parts needed, the modular design makes MAG-BEECO valves the easiest and quickest valve to perform your mandatory yearly recertification on. APPLICATIONS For installation on potable water lines Protects against back siphonage and back pressure Maximum protection in High Hazard applications FEATURES AND BENEFITS Fewer parts needed save money Servicing ability and commissioning is easy, simple and cost effective Easy Repair: Checks are designed with a unique thumb screw holding in the disc to allow for easy removal with a simple pair of pliers dramatically reducing part breakage during repair Ease of access means lower maintenance costs saving time and money Single threaded cover enables quick access inside the valve Repair parts are modular - only takes two relief valve kits and three check repair kits to cover all sizes Entire valve can be fully serviced inline lightweight short lay length modular design makes valve easy and quick to service Sizes: 15mm to 50mm device Body: Brass Noryl Replacement check valves Relief valve port independent of check valves Maximum working pressure: 1200kPa Maximum working temperature: 82 C Hydrostatic test pressure: 2400kPa 300 series stainless steel springs INSTALLATION Unless otherwise specified, install device at a minimum of 300mm above adequate drain with sufficient clearance for testing and maintenance. SPECIFICATION SAMPLE The RPZD shall be WaterMark approved rated at 82 C. The main body shall be all brass construction with Noryl replaceable check valves. The RPZD shall be MAG-BEECO.
AS/NZS 2845.1 Lic: WM 74542 Reduced Pressure Zone Device Model Dimensions MAG Product Code Valve Size mm A (Device only) B (Device, Y Strainer and 2 Ball Valves) Device Only With Y Strainer and 2 Ball Valves FRP-0.50LF - 15mm RPZ Device 15mm 169 346 B9315 B9315C FRP-0.75LF - 20mm RPZ Device 20mm 169 346 B9320 B9320C FRP-1.00LF - 25mm RPZ Device 25mm 201 413 B9325 B9325C FRP-1.25LF - 32mm RPZ Device 32mm 230 488 B9332 B9332C FRP-1.50LF - 40mm RPZ Device 40mm 228 516 B9340 B9340C FRP-2.00LF - 50mm RPZ Device 50mm 272 615 B9350 B9350C Figure 1 - Flow Rates FRP-0.50LF, FRP-0.75LF and FRP-1.00LF Figure 2- Flow Rates FRP-1.25LF, FRP-1.50LF and FRP-2.00LF
Reduced Pressure Zone Device (RPZs) - 65mm-250mm Testable High Hazard Designed with ease of access in mind and with very few spare parts needed, the modular design makes MAG-BEECO valves the easiest and quickest valve to perform your mandatory yearly recertification on. APPLICATIONS For installation on potable water lines Protects against back siphonage and back pressure Maximum protection in High Hazard applications FEATURES AND BENEFITS Shorter lay lengths Fewer parts needed save money Servicing ability and commissioning is easy, simple and cost effective Single threaded cover enables quick access inside the valve Ease of access means lower maintenance costs saving time and money Repair parts are modular - only takes two relief valve kits and three check repair kits to cover all sizes Entire valve can be fully serviced inline lightweight short lay length modular design makes this valve easy and quick to service Epoxy coated ductile iron construction Noryl Replacement check valves Relief valve port independent of check valves Maximum working pressure: 1200kPa Maximum working temperature: 60 C Hydrostatic test pressure: 2400kPa 300 series stainless steel springs Figure 1- Flow Rates FRP-2.50LF, FRP-3.00LF and FRP-4.00LF INSTALLATION Unless otherwise specified, install device at a minimum of 300mm above adequate drain with sufficient clearance for testing and maintenance. Figure 2- Flow Rates FRP-6.00LF, FRP-8.00LF and FRP-10.00LF SPECIFICATION SAMPLE The RPZD shall be WaterMark approved rated at 60 C. The main body shall be epoxy coated ductile iron construction with Noryl replaceable check valves. Both checks 1st and 2nd shall be accessible for maintenance without removing the device from the system. The RPZD shall be MAG-BEECO.
AS/NZS 2845.1 Lic: WM 74542 Reduced Pressure Zone Device Model Dimensions MAG Product Code FRP-2.50LF - 65mm RPZ Device FRP-3.00LF - 80mm RPZ Device FRP-4.00LF - 100mm RPZ Device FRP-6.00LF - 150mm RPZ Device FRP-8.00LF - 200mm RPZ Device FRP-10.00LF - 250mm RPZ Device Valve Size mm A (Device only) B (Strainer) C (Device, Y Strainer and 2 Butterfly Valves) C1 (Device, Y Strainer and 2 Gate Valves) Flange Type Number of Holes Device Only With Butterfly Valves and Y Strainer With Gate Valves and Y Strainer 65mm 470 290 852 1140 Table D 4 B9265 B9265C B9265GVS 80mm 470 320 882 1196 Table D 4 B9280 B9280C B9280GVS 100mm 470 380 954 1308 Table E 8 B92100 B92100C B92100GVS 150mm 578 570 1210 1632 Table E 8 B92150 B92150C B92150GVS 200mm 851 600 1573 2035 Table E 8 B92200 B92200C B92200GVS 250mm 851 730 1744 2241 Table E 12 B92250 B92250C B92250GVS Easy One-Clamp Access Design Easily Maintained Strong Durable Internal Checks Easily Repairable Seat & Diaphragm Easily Repairable Seat & Diaphragm Relief Valve is located at the bottom of the body when installed vertically. This ensures that all water will drain from the body.
Double Check Valve (DCVs) - 20mm-50mm Testable Medium Hazard Designed with ease of access in mind and with very few spare parts needed, the modular design makes MAG-BEECO valves the easiest and quickest valve to perform your mandatory yearly recertification on. APPLICATIONS For installation on potable water lines Protects against back siphonage and back pressure Maximum protection in Medium Hazard applications FEATURES AND BENEFITS Fewer parts needed save money Servicing ability and commissioning is easy, simple and cost effective Easy Repair: Checks are designed with a unique thumb screw holding in the disc to allow for easy removal with a simple pair of pliers dramatically reducing part breakage during repair Ease of access means lower maintenance costs saving time and money Entire valve can be fully serviced inline lightweight short lay length modular design makes this valve easy and quick to service Single threaded cover enables quick access inside the valve Repair parts are modular - only takes two relief valve kits and three check repair kits to cover all sizes Sizes: 20mm to 50mm Body: Brass Noryl TM Replacement check valves Relief valve port independent of check valves Maximum working pressure: 1200kPa Maximum working temperature: 82 C Hydrostatic test pressure: 2400kPa 300 series stainless steel springs INSTALLATION Install device as per AS3500 and any local applicable codes and manufacturer s instructions. SPECIFICATION SAMPLE The Double Check Valve backflow preventer shall be WaterMark approved rated at 82 C. The main body shall be all brass construction with Noryl replaceable check valves. Both checks 1st and 2nd shall be accessible for maintenance without removing the device from the system. The DCV shall be MAG-BEECO.
AS/NZS 2845.1 Lic: WM 74542 Double Check Valve Model Dimensions MAG Product Code Valve Size mm A (Device only) B (Device, Y Strainer and 2 Ball Valves) Device Only With 2 Ball Valves and Strainer FDC-0.75LF - 20mm DCV Device 20mm 169 346 B9120 B9120C FDC-1.00LF - 25mm DCV Device 25mm 201 413 B9125 B9125C FDC-1.25LF - 32mm DCV Device 32mm 230 488 B9132 B9132C FDC-1.50LF - 40mm DCV Device 40mm 228 516 B9140 B9140C FDC-2.00LF - 50mm DCV Device 50mm 272 615 B9150 B9150C Figure 1 - Flow Rate FDC-0.75LF and FDC-1.00LF Figure 2 - Flow Rates FDC-1.25LF, FDC-1.50LF and FDC-2.00LF
Double Check Valve (DCVs) - 65mm-250mm Testable Medium Hazard Designed with ease of access in mind and with very few spare parts needed, the modular design makes MAG-BEECO valves the easiest and quickest valve to perform your mandatory yearly recertification on. APPLICATIONS For installation on potable water lines Protects against back siphonage and back pressure Maximum protection in Medium Hazard applications FEATURES AND BENEFITS Shorter lay lengths Fewer parts needed save money Servicing ability and commissioning is easy, simple and cost effective Epoxy coated ductile iron construction Ease of access means lower maintenance costs saving time and money Single threaded cover enables quick access inside the valve Entire valve can be fully serviced inline lightweight short lay length modular design makes this valve easy and quick to service Repair parts are modular - only takes two relief valve kits and three check repair kits to cover all sizes Noryl TM Replacement check valves Relief valve port independent of check valves Maximum working pressure: 1200kPa Maximum working temperature: 60 C Hydrostatic test pressure: 2400kPa 300 series stainless steel springs INSTALLATION Install device as per AS3500 and any local applicable codes and manufacturer s instructions. SPECIFICATION SAMPLE The Double Check Valve backflow preventer shall be WaterMark approved rated at 60 C. The main body shall be epoxy coated ductile iron construction with Noryl replaceable check valves. Both checks 1st and 2nd shall be accessible for maintenance without removing the device from the system. The DCV shall be MAG-BEECO.
AS/NZS 2845.1 Lic: WM 74542 Double Check Valve Model Dimensions MAG Product Code FDC-2.50LF - 65mm DCV Device FDC-3.00LF - 80mm DCV Device FDC-4.00LF - 100mm DCV Device FDC-6.00LF - 150mm DCV Device FDC-8.00LF - 200mm DCV Device FDC-10.00LF - 250mm DCV Device Valve Size mm A (Device only) B (Strainer) C (Device, Strainer and 2 Butterfly Valves) C1 (Device, Strainer and 2 Gate Valves) Flange Type Number of Holes Device Only With Butterfly Valves and Strainer With Gate Valves and Strainer 65mm 470 290 852 1140 Table D 4 B9165 B9165C B9165GVS 80mm 470 320 882 1196 Table D 4 B9180 B9180C B9180GVS 100mm 470 380 954 1308 Table E 8 B91100 B91100C B91100GVS 150mm 578 570 1210 1632 Table E 8 B91150 B1150C B91150GVS 200mm 851 600 1573 2035 Table E 8 B91200 B91200C B91200GVS 250mm 851 730 1744 2241 Table E 12 B91250 B91250C B91250GVS Figure 1 - Flow Rates FDC-2.50LF and FDC-3.00LF Figure 2 - Flow Rates FDC-4.00LF Figure 3 - Flow Rates FDC-6.00LF, FDC-8.00LF and FDC-10.00LF
Reduced Pressure Zone Components Reduced Pressure Zone (2 1/2-10 ) Test Cock Lid Lid Clamp Lid Gasket Check Retainers Second Check Valve First Check Valve Epoxy Coated Ductile Iron Body Pressure Relief Valve Check Valve (2 1/2-10 ) Disk Seat Stem Stem O-Ring Bolts Washer Seat O-Ring Spring Diaphragm Piston Piston O-RIng Relief Valve (2 1/2-10 ) Nut Spring Check O-Ring Seat Bolt Disk Washer Disk Holder
Reduced Pressure Zone Components Reduced Pressure Zone (1/2-2 ) Test Cock Lid Lid O-Ring First Check Valve Plastic Spacer S Second Check Valve Ball Valve Cast Bronze Body Relief Valve Relief Check Valve Check Valve (1/2-2 ) Spring Disk Cap Screw Check Valve Body Check Valve Disc Retainer Check Valve O-Ring Check Valve Base Relief Valve (1/2-2 ) Seat Sub-Assembly Screw Stem Piston Seat O-Ring Spring Disc Diaphragm Piston O-Ring