Automotive Data Solutions Inc. INSTALL GUIDE ADS-AL(DL)-CH5-EN AVAILABLE FOR : ADS-AL CA Rev. Date: July 8, 208 Doc. No.: ##52026## CH5 U.S. PATENT NO. 8,856,780 PLEASE VISIT WWW.IDATALINK.COM FOR COMPLETE PRODUCT DETAILS The brand names and logos found in this guide are property of their respective owners. Automotive Data Solutions Inc. 208 TERMS OF USE: Automotive Data solutions Inc. ( ADs ) products are strictly intended for installation by Certified Technicians who are employed by a registered business specialized in the installation of automotive aftermarket electronics products. prior to beginning installation of an ADs product in a vehicle, it is the Certified Technician s responsibility to review the most current product guide, Install guide and vehicle-specific notes available in Weblink. ADs is not responsible for any damages whatsoever, including but not limited to any consequential damages, incidental damages, damages for loss of time, loss of earnings, loss of profit, commercial loss, loss of economic opportunity and the like that may or may not have resulted from the use, misuse, improper installation or operation of its products. ADs reserves itself the right to suspend any Weblink account without notice and decline to offer technical support to non- Certified Technicians, non-compliant Certified Technicians or end users.
Page 2 of 9 ADS-AL(DL)-CH5-EN Doc. No.: ##52026## 208077 INSTALL TYPE SELECTION FEATURES MAKE MODEL YEAR MITSUBISHI RAM JEEP DODGE CHRYSLER INSTALL TYPE DATA IMMOBILIZER BYPASS PRIORITY UNLOCK DOOR LOCK DOOR UNLOCK ARM OEM ALARM DISARM OEM ALARM TRUNK/HATCH RELEASE DOOR STATUS OUTPUT TRUNK STATUS OUTPUT BRAKE PEDAL STATUS OUTPUT E-BRAKE OUTPUT TACHOMETER OUTPUT DATA/MUX STARTER CTRL RAP SHUTDOWN CTRL 200-4 3 or 8 300 / 300C 05-07 or 6 Aspen 07-0 3 or 8 PT Cruiser 06-0 or 6 Sebring 07-0 3 or 8 Avenger 08-4 3 or 8 Caliber (with start wire) 07 or 6 Caliber 07-2 3 or 8 Charger 06-07 or 6 Dakota 05-06 4 Dakota 07-3 Durango 04-06 4 Durango 07-0 3 or 8 Magnum 05-07 or 6 Nitro 07-3 or 8 Ram 500 06 2 Ram 500 07-08 3 or 8 Ram 500 SRT 06 3 Ram 2500 06 2 Ram 2500 07-09 3 or 8 Ram 3500 05-06 2 Ram 3500 07-09 3 or 8 Ram 3500 chassis cab 07-09 3 or 8 Ram 4500 chassis cab 08-0 3 or 8 Ram 5500 chassis cab 08-0 3 or 8 Sprinter (requires key) 07-0 5 Commander 06-07 or 6 Compass 07-7 3 or 8 Grand Cherokee 05-07 or 6 Liberty 08-2 3 or 8 Patriot 07-7 3 or 8 Wrangler JK STD Key AT 07-8 3 or 8 4500 chassis cab 0 3 or 8 5500 chassis cab 0 3 or 8 Raider 05-06 4 Raider 07-09 3 Visit our website for advanced features.
Page 3 of 9 ADS-AL(DL)-CH5-EN Doc. No.: ##52026## 208077 TYPE - CROSS REFERENCE CHART - OF 2 MAKE MODEL YEAR CHRYSLER DESCRIPTION NAME TYPE DODGE POSITION POLARITY JEEP MODULE LOCATION COMPONENT LOCATOR 300 05-07 PT Cruiser 06-0 Caliber with start wire 07 Charger 06-07 Magnum 05-07 Commander 06 Commander 07 Mux ~ ~ 5 pin 2 Purple/Brown (DATA) Ignition switch ~ Ignition ~ ~ 5 pin 3 Pink/White (+) Ignition switch ~ Start ~ ~ 5 pin 4 Pink/DkGreen (+) Ignition switch ~ 2V ~ ~ 5 pin 5 LtBlue/Red (+) Ignition switch ~ Mux ~ ~ 5 pin 2 Purple/Brown (DATA) Ignition switch ~ Ignition ~ ~ 5 pin 3 Pink/White (+) Ignition switch ~ Start ~ ~ 5 pin 4 Pink/LtBlue (+) Ignition switch ~ 2V ~ ~ 5 pin 5 Red (+) Ignition switch ~ CanL ~ ~ 8 pin 7 White/Pink (DATA) Ignition switch ~ Mux ~ ~ 5 pin 2 Purple/Brown (DATA) Ignition switch ~ Ignition ~ ~ 5 pin 3 Pink/White (+) Ignition switch ~ Start ~ ~ 5 pin 4 Pink/LtBlue (+) Ignition switch ~ 2V ~ ~ 5 pin 5 Red/Orange (+) Ignition switch ~ Mux ~ ~ 5 pin 2 Purple/Brown (DATA) Ignition switch ~ Ignition ~ ~ 5 pin 3 Pink/White (+) Ignition switch ~ Start ~ ~ 5 pin 4 Pink/DkGreen (+) Ignition switch ~ 2V ~ ~ 5 pin 5 LtBlue/Red (+) Ignition switch ~ Mux ~ ~ 5 pin 2 Purple/Brown (DATA) Ignition switch ~ Ignition ~ ~ 5 pin 3 Pink/White (+) Ignition switch ~ Start ~ ~ 5 pin 4 Pink/DkGreen (+) Ignition switch ~ 2V ~ ~ 5 pin 5 LtBlue/Red (+) Ignition switch ~ Mux ~ ~ 5 pin 2 Purple/Brown (DATA) Ignition switch ~ Ignition ~ ~ 5 pin 3 Pink/LtGreen (+) Ignition switch ~ Start ~ ~ 5 pin 4 Pink/Orange (+) Ignition switch ~ 2V ~ ~ 5 pin 5 Blue/Red (+) Ignition switch ~ Mux ~ ~ 5 pin 2 Purple/Brown (DATA) Ignition switch ~ Ignition ~ ~ 5 pin 3 Pink/LtGreen (+) Ignition switch ~ Start ~ ~ 5 pin 4 Pink/Orange (+) Ignition switch ~ 2V ~ ~ 5 pin 5 Blue/Red (+) Ignition switch ~
Page 4 of 9 ADS-AL(DL)-CH5-EN Doc. No.: ##52026## 208077 TYPE - CROSS REFERENCE CHART - 2 OF 2 MAKE MODEL YEAR DESCRIPTION JEEP NAME TYPE POSITION POLARITY MODULE LOCATION COMPONENT LOCATOR Grand Cherokee 05-07 Mux ~ ~ 5 pin 2 Purple/Brown (DATA) Ignition switch ~ Ignition ~ ~ 5 pin 3 Pink/LtGreen (+) Ignition switch ~ Start ~ ~ 5 pin 4 Pink/Orange (+) Ignition switch ~ 2V ~ ~ 5 pin 5 Blue/Red (+) Ignition switch ~
Page 5 of 9 ADS-AL(DL)-CH5-EN Doc. No.: ##52026## 208077 TYPE - WIRING DIAGRAM IGNITION SWITCH 8 7 6 5 4 CANH CANL 3 2 5 AMPS START (+) 5 4 3 2 WARNING: DO NOT CONNECT ANY OTHER ACCESSORY, IGNITION OR START FROM THE REMOTE STARTER TO THE VEHICLE. REMOTE STARTER 2V (+) MUX IGNITION (+) STARTER (+) OUTPUT TACH (AC) INPUT E-BRAKE STATUS (-) INPUT TRUNK (-) OUTPUT UNLOCK (-) OUTPUT LOCK (-) OUTPUT 2V (+) GROUND (-) GROUND WHEN RUNNING (-) OUTPUT 2V (+) INPUT IGNITION (+) INPUT BRAKE (+) INPUT TRUNK STATUS (-) INPUT DOOR STATUS (-) INPUT CONNECT TO BCM OR BATTERY DO NOT CONNECT TO IGNITION SWITCH LEGEND NOT REQUIRED IN (-WAY) NOT REQUIRED IN (2-WAY) N400 DIODE USE OR HARD MODE GWR (-) INPUT - BLUE/WHITE GROUND - BLACK 2V (+) - RED LOCK/ARM (-) INPUT - GREEN/BLACK UNLOCK/DISARM (-) INPUT - BLUE/BLACK TRUNK (-) INPUT - RED/WHITE (NC) BROWN (NC) PURPLE/YELLOW (NC) PURPLE/BLACK STARTER (+) INPUT - BLACK/WHITE E-BRAKE STATUS (-) OUTPUT - GREEN TACH (AC) OUTPUT - PURPLE/WHITE WHITE/BLACK - IGNITION (+) OUTPUT WHITE/RED - IGNITION STATUS (+) OUTPUT WHITE - 2V (+) YELLOW/BLACK - DOOR STATUS (-) OUTPUT YELLOW/RED - TRUNK STATUS (-) OUTPUT YELLOW - MUX BROWN/RED - CANH BROWN/YELLOW - CANL ORANGE/BLACK (NC) ORANGE/WHITE (NC) ORANGE - BRAKE (+) OUTPUT PINK/BLACK (NC) PINK - IGNITION (+) INPUT BLUE/RED (NC) BLUE/YELLOW (NC) GREEN/RED (NC) GREEN/YELLOW (NC) GRAY/RED (NC) GRAY/YELLOW (NC)
Page 6 of 9 ADS-AL(DL)-CH5-EN Doc. No.: ##52026## 208077 TYPE 2 - CROSS REFERENCE CHART - OF MAKE MODEL YEAR DESCRIPTION NAME DODGE TYPE POSITION POLARITY MODULE LOCATION COMPONENT LOCATOR Ram 500 06 Ram 2500 06 Ram 3500 06 Mux ~ ~ 6 pin 2 Purple/Brown (DATA) Ignition switch ~ Ignition ~ ~ 6 pin 3 Pink/White (+) Ignition switch ~ Start ~ ~ 6 pin 4 DkGreen/Yellow (+) Ignition switch ~ 2V ~ ~ 6 pin 6 ~ (+) Ignition switch ~ Mux ~ ~ 6 pin 2 Purple/Brown (DATA) Ignition switch ~ Ignition ~ ~ 6 pin 3 Pink/White (+) Ignition switch ~ Start ~ ~ 6 pin 4 DkGreen/Yellow (+) Ignition switch ~ 2V ~ ~ 6 pin 6 ~ (+) Ignition switch ~ Mux ~ ~ 6 pin 2 Purple/Brown (DATA) Ignition switch ~ Ignition ~ ~ 6 pin 3 Pink/White (+) Ignition switch ~ Start ~ ~ 6 pin 4 DkGreen/Yellow (+) Ignition switch ~ 2V ~ ~ 6 pin 6 ~ (+) Ignition switch ~
Page 7 of 9 ADS-AL(DL)-CH5-EN Doc. No.: ##52026## 208077 TYPE 2 - WIRING DIAGRAM IGNITION SWITCH 8 7 6 5 4 CANH CANL 3 2 5 AMPS START (+) 6 5 4 3 2 WARNING: DO NOT CONNECT ANY OTHER ACCESSORY, IGNITION OR START FROM THE REMOTE STARTER TO THE VEHICLE. REMOTE STARTER 2V (+) MUX IGNITION (+) STARTER (+) OUTPUT TACH (AC) INPUT E-BRAKE STATUS (-) INPUT TRUNK (-) OUTPUT UNLOCK (-) OUTPUT LOCK (-) OUTPUT 2V (+) GROUND (-) GROUND WHEN RUNNING (-) OUTPUT 2V (+) INPUT IGNITION (+) INPUT BRAKE (+) INPUT TRUNK STATUS (-) INPUT DOOR STATUS (-) INPUT CONNECT TO BCM OR BATTERY DO NOT CONNECT TO IGNITION SWITCH LEGEND NOT REQUIRED IN (-WAY) NOT REQUIRED IN (2-WAY) N400 DIODE USE OR HARD MODE GWR (-) INPUT - BLUE/WHITE GROUND - BLACK 2V (+) - RED LOCK/ARM (-) INPUT - GREEN/BLACK UNLOCK/DISARM (-) INPUT - BLUE/BLACK TRUNK (-) INPUT - RED/WHITE (NC) BROWN (NC) PURPLE/YELLOW (NC) PURPLE/BLACK STARTER (+) INPUT - BLACK/WHITE E-BRAKE STATUS (-) OUTPUT - GREEN TACH (AC) OUTPUT - PURPLE/WHITE WHITE/BLACK - IGNITION (+) OUTPUT WHITE/RED - IGNITION STATUS (+) OUTPUT WHITE - 2V (+) YELLOW/BLACK - DOOR STATUS (-) OUTPUT YELLOW/RED - TRUNK STATUS (-) OUTPUT YELLOW - MUX BROWN/RED - CANH BROWN/YELLOW - CANL ORANGE/BLACK (NC) ORANGE/WHITE (NC) ORANGE - BRAKE (+) OUTPUT PINK/BLACK (NC) PINK - IGNITION (+) INPUT BLUE/RED (NC) BLUE/YELLOW (NC) GREEN/RED (NC) GREEN/YELLOW (NC) GRAY/RED (NC) GRAY/YELLOW (NC)
Page 8 of 9 ADS-AL(DL)-CH5-EN Doc. No.: ##52026## 208077 TYPE 3 - CROSS REFERENCE CHART - OF 2 MAKE CHRYSLER MODEL YEAR DODGE DESCRIPTION NAME TYPE POSITION POLARITY MODULE LOCATION COMPONENT LOCATOR 200-4 Aspen 07-0 Sebring 07-0 Avenger 08-4 Caliber 07-2 Dakota 07- Durango 07-0 Nitro 07- Ram Pickup 07-0 Ignition ~ ~ 8 pin 3 Pink (+) Ignition switch ~ 2V ~ ~ 8 pin 5 Red (+) Ignition switch ~ Ignition ~ ~ 8 pin 3 Pink/Gray (+) Ignition switch ~ 2V ~ ~ 8 pin 5 Red (+) Ignition switch ~ Ignition ~ ~ 8 pin 3 Pink (+) Ignition switch ~ 2V ~ ~ 8 pin 5 Red (+) Ignition switch ~ Ignition ~ ~ 8 pin 3 Pink (+) Ignition switch ~ 2V ~ ~ 8 pin 5 Red (+) Ignition switch ~ CanL ~ ~ 8 pin 7 White/Pink (DATA) Ignition switch ~ Ignition ~ ~ 8 pin 3 Pink/White (+) Ignition switch ~ 2V ~ ~ 8 pin 5 Red/LtBlue (+) Ignition switch ~ Ignition ~ ~ 8 pin 3 Pink/Gray (+) Ignition switch ~ 2V ~ ~ 8 pin 5 Red/LtBlue (+) Ignition switch ~ CanL ~ ~ 8 pin 7 White/LtBlue (DATA) Ignition switch ~ Ignition ~ ~ 8 pin 3 Pink/Gray (+) Ignition switch ~ 2V ~ ~ 8 pin 5 Red (+) Ignition switch ~ CanH ~ ~ 8 pin 6 White/LtGreen (DATA) Ignition switch ~ Ignition ~ ~ 8 pin 3 Pink/White (+) Ignition switch ~ 2V ~ ~ 8 pin 5 Red (+) Ignition switch ~ Ignition ~ ~ 8 pin 3 Pink/White (+) Ignition switch ~ 2V ~ ~ 8 pin 5 Gray/Red (+) Ignition switch ~
Page 9 of 9 ADS-AL(DL)-CH5-EN Doc. No.: ##52026## 208077 TYPE 3 - CROSS REFERENCE CHART - 2 OF 2 MAKE JEEP MODEL YEAR RAM DESCRIPTION NAME TYPE POSITION MITSUBISHI POLARITY MODULE LOCATION COMPONENT LOCATOR Compass 07-7 Liberty 08-2 Patriot 07-7 Wrangler JK STD Key AT Pickup 0 07-8 Raider 07-09 CanL ~ ~ 8 pin 7 White/Pink (DATA) Ignition switch ~ Ignition ~ ~ 8 pin 3 Pink/White (+) Ignition switch ~ 2V ~ ~ 8 pin 5 Red/LtGreen (+) Ignition switch ~ CanH ~ ~ 8 pin 6 White/Black (DATA) Ignition switch ~ CanL ~ ~ 8 pin 7 White/Blue (DATA) Ignition switch ~ Ignition ~ ~ 8 pin 3 Pink/White (+) Ignition switch ~ 2V ~ ~ 8 pin 5 Red (+) Ignition switch ~ CanL ~ ~ 8 pin 7 White/Pink (DATA) Ignition switch ~ Ignition ~ ~ 8 pin 3 Pink/White (+) Ignition switch ~ 2V ~ ~ 8 pin 5 Red/LtGreen (+) Ignition switch ~ CanH ~ ~ 8 pin 6 White/Black (DATA) Ignition switch ~ CanL ~ ~ 8 pin 7 White/LtBlue (DATA) Ignition switch ~ Ignition ~ ~ 8 pin 3 Pink/White (+) Ignition switch ~ 2V ~ ~ 8 pin 5 Red (+) Ignition switch ~ Ignition ~ ~ 8 pin 3 Pink/White (+) Ignition switch ~ 2V ~ ~ 8 pin 5 Gray/Red (+) Ignition switch ~ Ignition ~ ~ 8 pin 3 Pink/Gray (+) Ignition switch ~ 2V ~ ~ 8 pin 5 Red/LtBlue (+) Ignition switch ~
Page 0 of 9 ADS-AL(DL)-CH5-EN Doc. No.: ##52026## 208077 TYPE 3 - WIRING DIAGRAM IGNITION SWITCH MUX IGNITION (+) 2V (+) 8 7 6 5 4 3 2 CANH CANL WARNING: DO NOT CONNECT ANY OTHER ACCESSORY, IGNITION OR START FROM THE REMOTE STARTER TO THE VEHICLE. REMOTE STARTER CONNECT TO BCM OR BATTERY DO NOT CONNECT TO IGNITION SWITCH MANUAL TRANSMISSION ONLY TACH (AC) INPUT E-BRAKE STATUS (-) INPUT STARTER (+) OUTPUT TRUNK (-) OUTPUT UNLOCK (-) OUTPUT LOCK (-) OUTPUT 2V (+) GROUND (-) GROUND WHEN RUNNING (-) OUTPUT <- OPTIONAL <- OPTIONAL 2V (+) INPUT IGNITION (+) INPUT BRAKE (+) INPUT TRUNK STATUS (-) INPUT DOOR STATUS (-) INPUT LEGEND NOT REQUIRED IN (-WAY) NOT REQUIRED IN (2-WAY) N400 DIODE USE OR HARD MODE GWR (-) INPUT - BLUE/WHITE GROUND - BLACK 2V (+) - RED LOCK/ARM (-) INPUT - GREEN/BLACK UNLOCK/DISARM (-) INPUT - BLUE/BLACK TRUNK (-) INPUT - RED/WHITE (NC) BROWN (NC) PURPLE/YELLOW (NC) PURPLE/BLACK STARTER (+) INPUT - BLACK/WHITE E-BRAKE STATUS (-) OUTPUT - GREEN TACH (AC) OUTPUT - PURPLE/WHITE WHITE/BLACK - IGNITION (+) OUTPUT WHITE/RED - IGNITION STATUS (+) OUTPUT WHITE - 2V (+) YELLOW/BLACK - DOOR STATUS (-) OUTPUT YELLOW/RED - TRUNK STATUS (-) OUTPUT YELLOW - MUX BROWN/RED - CANH BROWN/YELLOW - CANL ORANGE/BLACK (NC) ORANGE/WHITE (NC) ORANGE - BRAKE (+) OUTPUT PINK/BLACK (NC) PINK - IGNITION (+) INPUT BLUE/RED (NC) BLUE/YELLOW (NC) GREEN/RED (NC) GREEN/YELLOW (NC) GRAY/RED (NC) GRAY/YELLOW (NC)
Page of 9 ADS-AL(DL)-CH5-EN Doc. No.: ##52026## 208077 TYPE 4 - CROSS REFERENCE CHART - OF MAKE MODEL YEAR DODGE DESCRIPTION NAME MITSUBISHI TYPE POSITION POLARITY MODULE LOCATION COMPONENT LOCATOR Dakota 05-06 Durango 04-06 Raider 05-06 Ignition ~ ~ 8 pin 3 Pink/Gray (+) Ignition switch ~ Ignition ~ ~ 8 pin 3 Pink/Gray (+) Ignition switch ~ Ignition ~ ~ 8 pin 3 Pink/Gray (+) Ignition switch ~
Page 2 of 9 ADS-AL(DL)-CH5-EN Doc. No.: ##52026## 208077 TYPE 4 - WIRING DIAGRAM IGNITION SWITCH 8 7 6 5 4 3 CANH CANL 2 IGNITION (+) WARNING: STANDARD REMOTE STARTER CONNECTIONS TO VEHICLE ARE REQUIRED. TEST S AND CONNECT ACCORDINGLY. MAY TAKE UP TO: 2x IGNITION (+) 3x ACCESSORY (+) / (-) x START (+) x KEYSENSE (-) REMOTE STARTER TACH (AC) INPUT E-BRAKE STATUS (-) INPUT STARTER (+) OUTPUT TRUNK (-) OUTPUT UNLOCK (-) OUTPUT LOCK (-) OUTPUT 2V (+) GROUND (-) GROUND WHEN RUNNING (-) OUTPUT BRAKE (+) INPUT TRUNK STATUS (-) INPUT DOOR STATUS (-) INPUT LEGEND NOT REQUIRED IN (-WAY) NOT REQUIRED IN (2-WAY) USE OR HARD MODE GWR (-) INPUT - BLUE/WHITE GROUND - BLACK 2V (+) - RED LOCK/ARM (-) INPUT - GREEN/BLACK UNLOCK/DISARM (-) INPUT - BLUE/BLACK TRUNK (-) INPUT - RED/WHITE (NC) BROWN (NC) PURPLE/YELLOW (NC) PURPLE/BLACK STARTER (+) INPUT - BLACK/WHITE E-BRAKE STATUS (-) OUTPUT - GREEN TACH (AC) OUTPUT - PURPLE/WHITE WHITE/BLACK (NC) WHITE/RED (NC) WHITE (NC) YELLOW/BLACK - DOOR STATUS (-) OUTPUT YELLOW/RED - TRUNK STATUS (-) OUTPUT YELLOW (NC) BROWN/RED - CANH BROWN/YELLOW - CANL ORANGE/BLACK (NC) ORANGE/WHITE (NC) ORANGE - BRAKE (+) OUTPUT PINK/BLACK (NC) PINK - IGNITION (+) INPUT BLUE/RED (NC) BLUE/YELLOW (NC) GREEN/RED (NC) GREEN/YELLOW (NC) GRAY/RED (NC) GRAY/YELLOW (NC)
XX-XX SOLDERING NOTICE INSTALL GUIDE PAGE X-X ADS-AL(DL)-CH5-EN Page 3 of 9 Doc. No.: ##52026## 208077 NOTICE SOLDERING NOTICE THIS MODIFICATION REQUIRES PRECISION SOLDERING SKILLS AND NEEDS TO BE PERFORMED WITH EXTREME CARE BY AN EXPERIENCED INSTALLER. USE It is very important not to overheat the electronic component during the soldering process. In order to do so, we recommend to use the following precision soldering station. DO NOT USE XX-XX ADS-AL(DL)-CH3 R The following equipment is NOT RECOMMENDED for this modification as it may burn, damage, move or unsolder electronic components on the circuit board due to overheating. PAGE X-X S IGNITION CYLINDER MODIFICATION TYPE 5 READ CAREFULLY AND EXECUTE WITH EXTREME CARE. MANUFACTURER TAKES NO RESPONSIBILITY FOR DAMAGES TO THE KEY CYLINDER. Press the release pins to open the plastic casing. 3 Solder ORANGE/WHITE and ORANGE/BLACK wires on circuit board as show below. Be careful not to overheat the welding points as it may seriously damage components on the board. ORANGE/WHITE FROM MODULE WARNING: PLEASE MAKE SURE THAT THE KEYSENSE TAB SHOWN IN THE PICTURE REMAINS IN ITS EXACT POSITION AND FREE TO MAKE ITS MECHANICAL MOVEMENT UPON IGNITION CYLINDER REASSEMBLY. 2 Locate the serial number on your circuit board. If the number is equal to EZS NCV3 DODGE as shown below, proceed to step 3. ORANGE/BLACK FROM MODULE CIRCUIT BOARD FOUND AT KEYPORT 4 EZS NCV3 DODGE EZS NCV3 DODGE WARNING: IF THE SERIAL NUMBER DOESN T MATCH, DO NOT PROCEED WITH MODIFICATION AND CALL TECHNICAL SUPPORT FOR FURTHER ASSISTANCE. WWW.IDATALINK.COM We strongly recommend using glue to secure the wires and to ensure long term integrity of the welds. Do not hesitate to zoom into the document to obtain a better view. HOT GLUE 5 Place the circuit board inside the key barrel and reassemble the plastic casing. Automotive Data Solutions Inc. 208
Page 4 of 9 ADS-AL(DL)-CH5-EN Doc. No.: ##52026## 208077 TYPE 5 - WIRING DIAGRAM RED/GREEN 87 BLACK 2 3 4 5 RED/GRAY BLACK/ORANGE BLACK 85 87A 30 86 WHITE 4 3 2 8 7 6 5 BROWN/RED BROWN 5-6 LOOPS AROUND KEY 5-6 LOOPS AROUND KEYBARREL REMOTE STARTER GRW (-) OR IGN 3 (-) TACH (AC) INPUT E-BRAKE STATUS (-) INPUT STARTER (+) OUTPUT UNLOCK BACKDOOR ONLY (-) OUTPUT UNLOCK (-) OUTPUT LOCK (-) OUTPUT 2V (+) GROUND (-) GROUND WHEN RUNNING (-) OUTPUT BATTERY IGNITION (+) IGNITION 2 (+) BRAKE (+) INPUT TRUNK STATUS (-) INPUT DOOR STATUS (-) INPUT LEGEND NOT REQUIRED IN (-WAY) NOT REQUIRED IN (2-WAY) USE OR HARD MODE GWR (-) INPUT - BLUE/WHITE GROUND - BLACK 2V (+) - RED LOCK/ARM (-) INPUT - GREEN/BLACK UNLOCK/DISARM (-) INPUT - BLUE/BLACK UNLOCK BACKDOOR ONLY (-) INPUT - RED/WHITE (NC) BROWN (NC) PURPLE/YELLOW (NC) PURPLE/BLACK STARTER (+) INPUT - BLACK/WHITE E-BRAKE STATUS (-) OUTPUT - GREEN TACH (AC) OUTPUT - PURPLE/WHITE WHITE/BLACK WHITE/RED (NC) WHITE YELLOW/BLACK - DOOR STATUS (-) OUTPUT YELLOW/RED - TRUNK STATUS (-) OUTPUT YELLOW (NC) BROWN/RED - CANH BROWN/YELLOW - CANL ORANGE/BLACK ORANGE/WHITE! ORANGE - BRAKE (+) OUTPUT PINK/BLACK (NC) PINK - IGNITION (+) INPUT! BLUE/RED (NC) BLUE/YELLOW (NC) GREEN/RED (NC) GREEN/YELLOW (NC) GRAY/RED (NC) GRAY/YELLOW (NC)! SEE IGNITION MODIFICATION PROCEDURE
Page 5 of 9 ADS-AL(DL)-CH5-EN Doc. No.: ##52026## 208077 TYPE 6 - WIRING DIAGRAM TACH (AC) INPUT E-BRAKE STATUS (-) INPUT STARTER (+) OUTPUT TRUNK (-) OUTPUT UNLOCK (-) OUTPUT LOCK (-) OUTPUT 2V (+) GROUND GROUND WHEN RUNNING (-) OUTPUT LEGEND NOT REQUIRED IN (-WAY) NOT REQUIRED IN (2-WAY) USE OR HARD MODE REMOTE STARTER J PURPLE GREEN/RED DOOR STATUS (-) - YELLOW/BLACK TRUNK STATUS (-) - YELLOW/RED BRAKE STATUS (+) - ORANGE IGNITION (+) - WHITE/RED 2V (+) - RED/WHITE GROUND (-) - BLACK 5 4 3 2 START MUX F H IDATALINK MODE GWR (-) INPUT - BLUE/WHITE GROUND - BLACK 2V (+) - RED E D LOCK/ARM (-) INPUT - GREEN/BLACK UNLOCK/DISARM (-) INPUT - BLUE/BLACK TRUNK (-) INPUT - RED/WHITE (NC) BROWN (NC) PURPLE/YELLOW (NC) PURPLE/BLACK STARTER (+) INPUT - BLACK/WHITE E-BRAKE STATUS (-) OUTPUT - GREEN *TACH (AC) OUTPUT - PURPLE/WHITE A B C BLUE/RED (NC) BLUE/YELLOW (NC) GREEN/RED (NC) GREEN/YELLOW (NC) GRAY/RED (NC) GRAY/YELLOW (NC) ADS-HRN CH5 F E D A B C CUT AND INSULATE THE PURPLE (NEXT TO WHITE ) ASSEMBLY SOLD SEPARATELY VEHICLE HARNESS G J H G
Page 6 of 9 ADS-AL(DL)-CH5-EN Doc. No.: ##52026## 208077 TACH (AC) INPUT E-BRAKE STATUS (-) INPUT STARTER (+) OUTPUT TRUNK (-) OUTPUT UNLOCK (-) OUTPUT LOCK (-) OUTPUT 2V (+) GROUND GROUND WHEN RUNNING (-) OUTPUT LEGEND NOT REQUIRED IN (-WAY) NOT REQUIRED IN (2-WAY) USE OR HARD MODE TYPE 7 - WIRING DIAGRAM REMOTE STARTER IGNITION (+) OUTPUT J PURPLE GREEN/RED DOOR STATUS (-) - YELLOW/BLACK TRUNK STATUS (-) - YELLOW/RED BRAKE STATUS (+) - ORANGE IGNITION (+) - WHITE/RED 2V (+) - RED/WHITE GROUND (-) - BLACK START F 6 5 4 3 2 H MUX IGNITION (+) GWR (-) INPUT - BLUE/WHITE GROUND - BLACK 2V (+) - RED E D LOCK/ARM (-) INPUT - GREEN/BLACK UNLOCK/DISARM (-) INPUT - BLUE/BLACK TRUNK (-) INPUT - RED/WHITE (NC) BROWN (NC) PURPLE/YELLOW (NC) PURPLE/BLACK STARTER (+) INPUT - BLACK/WHITE E-BRAKE STATUS (-) OUTPUT - GREEN TACH (AC) OUTPUT - PURPLE/WHITE A B C BLUE/RED (NC) BLUE/YELLOW (NC) GREEN/RED (NC) GREEN/YELLOW (NC) GRAY/RED (NC) GRAY/YELLOW (NC) ADS-HRN CH5 F E D A B C CUT AND INSULATE THE PURPLE (NEXT TO WHITE ) ASSEMBLY SOLD SEPARATELY VEHICLE HARNESS G J H G
Page 7 of 9 ADS-AL(DL)-CH5-EN Doc. No.: ##52026## 208077 TYPE 8 - WIRING DIAGRAM TACH (AC) INPUT E-BRAKE STATUS (-) INPUT STARTER (+) OUTPUT TRUNK (-) OUTPUT UNLOCK (-) OUTPUT LOCK (-) OUTPUT 2V (+) GROUND GROUND WHEN RUNNING (-) OUTPUT REMOTE STARTER DOOR STATUS (-) - YELLOW/BLACK TRUNK STATUS (-) - YELLOW/RED BRAKE STATUS (+) - ORANGE IGNITION (+) - WHITE/RED 2V (+) - RED/WHITE GROUND (-) - BLACK F LEGEND NOT REQUIRED IN (-WAY) NOT REQUIRED IN (2-WAY) USE OR HARD MODE GWR (-) INPUT - BLUE/WHITE GROUND - BLACK 2V (+) - RED E D LOCK/ARM (-) INPUT - GREEN/BLACK UNLOCK/DISARM (-) INPUT - BLUE/BLACK TRUNK (-) INPUT - RED/WHITE (NC) BROWN (NC) PURPLE/YELLOW (NC) PURPLE/BLACK STARTER (+) INPUT - BLACK/WHITE E-BRAKE STATUS (-) OUTPUT - GREEN TACH (AC) OUTPUT - PURPLE/WHITE A B C BLUE/RED (NC) BLUE/YELLOW (NC) GREEN/RED (NC) GREEN/YELLOW (NC) GRAY/RED (NC) GRAY/YELLOW (NC) ADS-HRN CH5 F E D A B C ASSEMBLY VEHICLE HARNESS SOLD SEPARATELY G G
Page 8 of 9 ADS-AL(DL)-CH5-EN Doc. No.: ##52026## 208077 INSTALLATION MODE SELECTION Press and release programming button to select installation mode. LED flashes (X) once = LED flashes (2X) twice = STANDARD HARD MODE 2! Press and hold programming button until LED turns solid GREEN to register selection. After registration, follow Factory Reset Procedure to change installation mode and restart this procedure. TYPE -4 & 6-8 - MODULE PROGRAMMING PROCEDURE Insert key into ignition. 6 Remove key. 2 ON Turn key to ON position. 7 UNLOCK Press UNLOCK on the OEM remote. 3 LED will turn solid RED. If vehicle is not equipped with OEM remote, press module programming button. 4 Within 5 seconds, LED will flash GREEN rapidly. 8 Wait, LED will turn solid GREEN for 2 seconds. 5 OFF Turn key to OFF position. 9 Module Programming Procedure completed. TYPE 5 - MODULE PROGRAMMING PROCEDURE Insert key into ignition. 4 OFF Turn key to OFF position. 2 ON Turn key to ON position. 5 Remove key. 3 Wait, LED will turn solid GREEN for 2 seconds. 6 Module Programming Procedure completed.
Page 9 of 9 ADS-AL(DL)-CH5-EN Doc. No.: ##52026## 208077 IDENTIFY VEHICLE YEAR Locate the Vehicle Identification Number (VIN), identify the 0th character then match it to its corresponding year. Æ 4 3 A 5 Y N 5 T A L 8 D 5 R 0 X Æ A 980 L 990 Y 2000 A 200 B 98 M 99 200 B 20 C 982 N 992 2 2002 C 202 D 983 P 993 3 2003 D 203 E 984 R 994 4 2004 E 204 F 985 S 995 5 2005 F 205 G 986 T 996 6 2006 G 206 H 987 V 997 7 2007 H 207 J 988 W 998 8 2008 J 208 K 989 X 999 9 2009 K 209 LED STATUS Flashing RED DIAGNOSTICS DURING PROGRAMMING DURING REMOTE START WITH IGNITION OFF Missing/wrong information from firmware or vehicle Incorrectly programmed Solid RED Waiting for more vehicle information Incorrectly programmed Flashing GREEN Additional steps required to complete programming MODULE DIAGNOSTICS Correctly programmed and operational Incorrectly programmed or connected Not programmed waiting for more vehicle information False ground when running status from remote starter Solid GREEN then OFF Correctly programmed Reset in progress Reset in progress OFF No activity or already programmed Invalid ground when running status from remote starter At rest and ready for a remote start sequence FACTORY RESET PROCEDURE 2 DISCONNECT all connectors from module EXCEPT the black 4-PIN standard or optional data connector. DISCONNECT black 4-PIN standard or optional data connector. 5 6 LED will turn solid red for 2 seconds. RESET COMPLETED. RECONNECT all connectors. 3 PRESS AND HOLD programming button while connecting either 4-PIN standard or optional data connector. 7! Repeat programming procedure. Failure to follow procedure may result with a DTC or a CHECK ENGINE error message. 4 When LED flashes red, RELEASE programming button.