EDIU VOLTAGE DRIVE STARTER TYPE V-S-L1 UP TO 20 W UP TO 12 KV UP TO 520/2500 A
OCOTECH PRESENTS THE VARIABLE FREQUENCY DRIVE STARTER TYPE V-S & The V- is based on multi level voltage source inverter technology for continuous operation and designed as V-S for short time operation. Drive starter applications: Starting of standard asynchronous and synchronous motors. Retrofit to any existing inductionand wound rotor motor. The highly sophisticated guarantees a very smooth continuous speed control and step-less acceleration without any mechanical shock to the motor and the load (if used as S drive starter until full speed and the bypass is closed). CUSTOER ADVANTAGES Up to 520 A output and 2500 A by-pass current at 2,3 kv Starting current rated motor current up to rated motor torque Starting current is a fraction of motor current at reduced load No need to oversize feeding transformers or generators No starting related voltage drop in the power supply Synchronized by-pass control Zero active power losses after by-pass closed Improves efficiency saves operation cost Perfect sinusoidal waves No harmonic filter required inimum common mode voltage to motor winding Negligible torque ripple, noise and heat caused by harmonics in. du/dt and di/dt very low EI Long motor cables possible PW based U/f also called VVVF control PW based vector control incl. field orientation control Open and closed loop control Increases lifetime of drives and machines Highest availability and operation stability Cost saving compact modular design with many options All equipment available in the drive starter, ready for operation: Input contactor Output contactor By-pass contactor ulti level phase shift input transformer Starting power electronics HI + central controller + PLC for starting control Totally digital controlled with self-test diagnostic function any acceleration/starting ramps possible Soft start/stop function with lowest mechanical stress Load dependent calculated starting voltage and current Inductive full load test before delivery
COPONENTS U PERFECT SINUSOIDAL WAVES V DRAW OUT POWER CELLS SERIAL H-BRIDGE TOPOLOGY TEP. SENSOR IN EACH IGBT W INTERCHANGEABLE POWER CELLS EASY SERVICE & AINTENANCE ODULAR ATTACHABLE PANELS V CONTACTORS ATTACHED UP TO 30 PULSE RIGID, STRONG, VERY RELIABLE HEAVY DUTY DESIGN
ON OFF ON OFF ON OFF SINGLE LINE DIAGRA SINGLE LINE DIAGRA OPTIONS A 1 9 + 10 1 External power supply feeder panel 2 S starter panel HI 3 By-pass contactor 12 4 S line contactor 5 S output contactor 7 V voltage sensor 7 Current sensor Earthing bolts 9 ulti winding transformer B 1 2 9 10 10 Power cells panel 4 Power cells 3 S HI 12 12 HI + central controller + starting control PLC 5 7 INSTALLATION ALTERNATIVES A Stand alone B Stand alone S C AINS IN OUT IN 1 1 DOL 2 2 DOL C Double bus bar V panels with S and cascade control for many motors
TECHNICAL DATA Rated voltage up to 12 kv Input voltage 2,3 kv Output voltage 2,3 kv Starting voltage range 0 kv Rated starting time 5 90 sec Rated starting current up to 520 A Rated by-pass current up to 2500 A Rated short time current up to 40 ka Rated peak withstand current up to 100 ka Rated starting power up to 10.000 kva full load otor starting up to 20.000 kw partial loaded Operating frequency 0 5 Hz Output frequency resolution 0,01 Hz Control totally digital with signal processor, PLC and 5 color HI Control mode V/F or vector control, open & closed loop with encorder Cooling method NA / FA air cooling Heat dissipation sample < 0,15 kwh by-pass closed (without stand still heater) Additional heat dissipation sample 0, 2,1 kwh one start/h for 0,25 5 W/30s Enclosure protection class IP 3x acc to IEC 100 Painting of doors RAL 7035 (light grey) Steel sheet panel covers powder coated, frame galvanized Ambient requirements Indoor, normal air, refer to 4.2..2.2 of IEC 100-5-1 pollution degree 2 Altitude above sea level 1000 m Rated ambient temperature 40 C Ambient temperature 0 + 55 C de-rated operating - 40 + 70 C storage Designed under consideration of IEC 100-5-1; IEEE 519-2000 Height / Depth 2400 / 1300 mm Width 3250 700 mm complete with V contactors & control AVAILABLE OPTIONS DTC (direct torque control) By-pass up to kv/2500a/40ka-1s Soft stop Braking stop AFE (active front end) power modules Iron core ct s Earthing switch Protection relays Different control signals and bus options Approval BV; DNV GL; LR; RINA; CE EXPLANATIONS Some illustrations in this brochure are typical or show options and might vary from standard and real design. Higher and other values can be offered on request. Please demand our general technical specification (GTS) describing all product features and options in detail.
PROFILE The first choice for the start of your motors should be a company that concentrates on your specific project requirement and bear full responsibility for design and realization of your starters. Based on well proven technology the company produces tailor made solutions combined with the flexibility to implement your individual project goals with high quality. We pay our full attention to the targets, select, design, produce and test our motor starters individually with solid equipment for your applications. We guarantee the service availability and operation stability of your plants with our motor starters. 0 years experiences in drive technology ensure your success. PRODUCT The surfer in the perfect wave represents the analogy of perfect sinusoidal wave output modulated from the V-S-L1 as shown on the cover page of this brochure. Our customers can reach the best performance in starting induction motors, synchronous motors and old slipring motors. It is possible to start and accelerate all kinds of load to full speed such as mills, belt, conveyers, compressors, blowers, fans, shredder, refiners, extruder, mixer, propellers, thrusters etc. We prove frequently that our products reach and exceed the demands from our customers even for disadvantageous load and power requirement in harsh and difficult environment. You receive at ocotech the highest value for your drive technology budget. SERVICE Qualified and experienced engineers, technicians and commercial staff take every day the full responsibility for the design, engineering, production, quality control, logistic, after sales service and training of our customers and partners in our headquarter in Rheinberg, Germany. Site support may be provided from our local dealer and agents located in many areas around the world. COITENT We are pleased to serve the steady increasing number of single and frequent customers that donate their trust in our company. Our commitment is the reliability and availability of your drives in top quality. You can always expect the best from ocotech. mocotech gmbh Nordring 20 47495 Rheinberg Germany phone +49 (0)243 904-0 fax +49 (0)243 904-44 info@mocotech.de www.mocotech.de