EWR MODELS EWR820, EWR1023, EWR1227 PULL TYPE HAY RAKES Published 04/11 PARTS MANUAL SECTION 19 MATERIAL HANDLING PARTS MANUAL
PARTS ORDERING GUIDE The following instructions are offered to help eliminate needless delay and error in processing purchase orders for the equipment in this section. 1. The Parts Section is prepared in logical sequence and grouping of parts that belong to the basic machine featured in this manual. Part Numbers and Descriptions are given to help locate the parts and quantities required. 2. The Purchase Order must include the name and address of the person or organization ordering the parts, who should be charged, and if possible, the serial number of the machine for which the parts are ordered. 3. The Purchase Order must clearly list the quantity of each part, the complete and correct part number (be sure to include all periods), and the basic name of the part. 4. The Manufacturer reserves the right to substitute parts where applicable. 5. Some parts are unlisted items which are special production items not normally stocked and are subject to special handling. Request a quotation for such parts before sending a Purchase Order. 6. The Manufacturer reserves the right to change prices without prior notice. For maximum safety and to guarantee optimum product reliability, always use genuine BUSH HOG Parts. The use of inferior replacement parts may causepremature or catastrophic failure which could result in serious injury or death.direct any questions regarding parts to: BUSH HOG 2501 Griffin Ave. Selma, AL 36703 www.bushhog.com Contact Us 800-304-2836 2009 Alamo Group Inc.
To the Owner/Operator/Dealer All implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-minded operator who recognizes the potential hazards and follows reasonable safety practices. The manufacturer has designed this implement to be used with all its safety equipment properly attached to minimize the chance of accidents. BEFORE YOU START! Read the safety messages on the implement and shown in your manual. Observe the rules of safety and common sense! WARRANTY INFORMATION: Read and understand the complete Warranty Statement found in this Manual. Fill out the Warranty RegistrationForm in full and return it to within 30 Days. Make certain the Serial Number of the Machine is recorded on thewarranty Card and on the Warranty Form that you retain.
LIMITED WARRANTY Bush Hog warrants to the original purchaser of any new Bush Hog equipment, purchased from an authorized Bush Hog dealer, that the equipment be free from defects in material and workmanship for a period of one (1) year for non-commercial, state and municipalities use and ninety (90) days for commercial use from date of retail sale. The obligation of Bush Hog to the purchaser under this warranty is limited to the repair or replacement of defective parts. Replacement or repair parts installed in the equipment covered by this limited warranty are warranted for ninety (90) days from the date of purchase of such part or to the expiration of the applicable new equipment warranty period, whichever occurs later. Warranted parts shall be provided at no cost to the user at an authorized Bush Hog dealer during regular working hours. Bush Hog reserves the right to inspect any equipment or parts which are claimed to have been defective in material or workmanship. DISCLAIMER OF IMPLIED WARRANTIES & CONSEQUENTIAL DAMAGES Bush Hog s obligation under this limited warranty, to the extent allowed by law, is in lieu of all warranties, implied or expressed, INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE and any liability for incidental and consequential damages with respect to the sale or use of the items warranted. Such incidental and consequential damages shall include but not be limited to: transportation charges other than normal freight charges; cost of installation other than cost approved by Bush Hog; duty; taxes; charges for normal service or adjustment; loss of crops or any other loss of income; rental of substitute equipment, expenses due to loss, damage, detention or delay in the delivery of equipment or parts resulting from acts beyond the control of Bush Hog. THIS LIMITED WARRANTY SHALL NOT APPLY: 1. To vendor items which carry their own warranties, such as engines, tires, and tubes. 2. If the unit has been subjected to misapplication, abuse, misuse, negligence, fire or other accident. 3. If parts not made or supplied by Bush Hog have been used in connection with the unit, if, in the sole judgement of Bush Hog such use affects its performance, stability or reliability. 4. If the unit has been altered or repaired outside of an authorized Bush Hog dealership in a manner which, in the sole judgement of Bush Hog, affects its performance, stability or reliability. 5. To normal maintenance service and normal replacement items such as gearbox lubricant, hydraulic fluid, worn blades, or to normal deterioration of such things as belts and exterior finish due to use or exposure. 6. To expendable or wear items such as teeth, chains, sprockets, belts, springs and any other items that in the company s sole judgement is a wear item. NO EMPLOYEE OR REPRESENTATIVE OF BUSH HOG IS AUTHORIZED TO CHANGE THIS LIMITED WARRANTY IN ANY WAY OR GRANT ANY OTHER WARRANTY UNLESS SUCH CHANGE IS MADE IN WRITING AND SIGNED BY BUSH HOG S SERVICE MANAGER, 2501 GRIFFIN AVE., SELMA, ALABAMA 36703. Record the model number, serial number and date purchased. This information will be helpful to your dealer if parts or service are required. MODEL NUMBER SERIAL NUMBER DATE OF RETAIL SALE MAKE CERTAIN THE WARRANTY HAS BEEN FILED WITH BUSH HOG SELMA, ALABAMA
BUSH HOG / MATERIAL HANDLING REPAIR PARTS MANUAL APRIL, 2011 ALPHABETICAL INDEX SECTION 18 MODELS EWR820, EWR1023, EWR1227 ITEM PAGE Cart Assembly...............................................19-1-1 Decals - Safety and Marking....................................19-1-8 Frame Assembly EWR820......................................19-1-2 Frame Assembly EWR1023.....................................19-1-3 Frame Assembly EWR1227.....................................19-1-4 Hydraulic Cylinder............................................19-1-6 Wheel Kit (Center)............................................19-1-7
NOTES:
BUSH HOG / MATERIAL HANDLING REPAIR PARTS MANUAL CART ASSY. EWR820, EWR1023, EWR1227 APRIL, 2011 1 3660300 Drawbar 1 2 3660301 Cart Frame (EWR820 &1023) 1 3690292 Cart Frame (EWR 1227) 1 3 3660302 LH Arm 1 4 3660303 RH Arm 1 7 3660304 Plate 1 8 3660305 LH Base 1 9 3667530 Bushing 2 10 N/A RH Base 1 11 3668602 Parking Stand (EWR820 &1023) 1 3668627 Parking Stand (EWR1227) 1 12 3667531 Hinge Pin 2 13 3637523 Cylinder Pin 4 14 3638602 Pin, Frame 1 15 3667223 Hose (EWR820 &1023) 2 3667224 Hose (EWR1227) 2 16 3667219 Hose 2 17 3667224 Hose 1 18 3638404 Copper Washer 4 19 3667143 Hydraulic Fitting 2 20 3667105 Hydraulic Fitting 1 21 3667144 Hydraulic Fitting 1 22 N/A Hydraulic Tee Fitting 2 23 3638408 Copper Washer 2 24 3637102 Coupling Tip 2 25 3667146 Cylinder, Hydraulic 2 3667147 Seal Kit 25 26 3668407 Washer 2 27 610914C8 Capscrew M16-2.0 x 150 12 28 758159 Roll Pin 2 29 3038445 Toplock Nut 12 30 N/A Nut M16 x 2 2 31 9313087 Capscrew M16-2 x 40 2 32 70502 Cotter PinM 6.3 X 36 8 33 N/A Roll Pin M8 X 50 2 34 3667525 Plate, Counter 2 35 3660307 Bracket, Hitch 1 37 3660235 Pin, Hitch 2 38 2568408 Grease Fitting 2 39 3638400 Hairpin Cotter 1 40 00762395 Bolt 2 41 3667504 Spindle, (EWR820 &1023) 2 3697549 Spindle, (EWR1227) 2 42 3666800 Seal 2 43 3666000 Bearing,Inner 2 44 3667505 Hub, Wheel 2 45 3666001 Bearing, Outer 2 46 3668408 Nut, Spindle 2 47 3638406 Nut 10 48 3666700 Cap, Hub 2 49 70487 Cotter Pin 2 50 3667800 Tire 2 51 N/A Wheel 2 52 3660106 Hub Assy (EWR820 &1023) 2 3660124 Hub Assy (EWR1227) 2 53 3660110 Mounted Tire Assembly 2 54 3668412 Hose Collar 2 55 3666253 Chain 1 56 3668603 Catch Spring 2 57 00757908 Chain, Safety Tow 1 19-1-1
BUSH HOG / MATERIAL HANDLING REPAIR PARTS MANUAL FRAME ASSY. EWR820 APRIL, 2011 2 3638401 Hairpin Cotter 1 4 3630233 Support Sector 1 5 3637500 Pin, Sector 1 6 N/A Washer 2 7 70503 Cotter Pin 2 8 3638602 Pin, Frame 1 9 3638400 Hairpin Cotter 5 10 N/A Bolt 1 11 N/A Nut, Top Lock 1 14 N/A Bolt 1 15 N/A Nut 1 16 3630204 Spring Mount, Upper 1 17 3637420 Spring, Extension 2 18 N/A Floating Arm 1 19 3630205 Spring Mount, Lower 1 20 3637501 Lock Plate 1 21 3637502 Lever Plate 3 22 3638402 Ring Retaining 6 23 3637503 Pin 3 24 3638601 Pin, Lever 3 25 3630235 Frame Main 1 26 3630105 Wheel Arm, Right 2 27 3630106 Wheel Arm, Left 2 30 3637509 Spindle, Weld-On 4 31 3736800 Seal 4 32 3736000 Bearing Set, Inner 4 33 3637504 Wheel Hub 4 34 3736001 Bearing Set, Outer 4 35 N/A Nut 4 36 N/A Cotter Pin 4 37 N/A Hub Cap 4 38 3630100 Hub & Spindle 4 39 N/A Bolt 24 40 00755954 Lock Washer 24 41 00755949 Nut 24 42 N/A Carriage Bolt 80 43 3637508 Tine Clamp 40 44 3637505 Flange 4 45 00755949 Nut 80 46 3637506 Rim 4 47 3737507 Tine 160 48 3630101 Wheel Assy. RH 4 49 3630102 Wheel Assy. LH 4 19-1-2
BUSH HOG / MATERIAL HANDLING REPAIR PARTS MANUAL FRAME ASSY. EWR 1023 APRIL, 2011 1 N/A Front Main Frame 1 2 3638401 Hairpin Cotter 1 3 N/A Nut, Top Lock 3 4 3630233 Support Sector 1 5 3637500 Pin Sector 1 6 N/A Washer 2 7 70503 Cotter Pin 2 8 3638602 Pin, Frame 1 9 3638400 Hairpin Cotter 5 10 N/A Bolt 1 11 N/A Nut, Top Lock 1 12 N/A Bolt 3 14 N/A Bolt 1 15 N/A Nut 1 16 3630204 Upper Spring Mount 1 17 3637420 Spring Extension 2 18 N/A Floating Arm 1 19 3630205 Lower Spring Mount 1 20 3637501 Lock Plate 1 21 3637502 Lever Plate 4 22 3638402 Retaining Ring 8 23 3637503 Pin 4 24 3638601 Pin, Lever 4 25 N/A Rear Main Frame 1 26 3630105 Wheel Arm, Right 2 27 3630106 Wheel Arm, Left 2 28 3630238 Arm, Front Wheel W/Hub 1 28a N/A Arm, Front Wheel W/O Hub 1 29 3630238 Arm, Front Wheel W/Hub 1 29a N/A Arm, Front Wheel W/O Hub 1 30 3637509 Spindle, Weld-On 5 31 3736800 Seal 5 32 3736000 Bearing Set, Inner 5 33 3637504 Wheel Hub 5 34 3736001 Bearing Set, Outer 5 35 N/A Nut 5 36 N/A Cotter Pin 5 37 N/A Hub Cap 5 38 3630100 Hub & Spindle 5 39 N/A Bolt 30 40 00755954 Lockwasher 30 41 00755949 Nut 30 42 N/A Carriage Bolt 100 43 3637508 Tine Clamp 50 44 3637505 Flange 5 45 00755949 Nut 100 46 3637506 Rim 5 47 3737507 Tine 200 48 3630101 Wheel Assy., RH 5 49 3630102 Wheel Assy., LH 5 19-1-3
BUSH HOG / MATERIAL HANDLING REPAIR PARTS MANUAL FRAME ASSY. EWR 1227 APRIL, 2011 10 3638400 Split Pin 10 13 3638401 Split Pin 2 14 70096C Nut M14 Din 980 6 15 N/A Screw M14x40 Din 933 8.8 6 16 3630247 Pipe - 6 Wheel 2 17 3630248 RH Support 1 17a 3630249 LHSupport 1 18 2568408 Grease Nipple M8 2 19 3638602 Pin 2 20 3637529 Pin 2 21 N/A Washer 25 Lock, M24 X 3 2 22 700135C Nut M24 X 3 2 23 N/A Screw M14 X 120 Din 931 8.8 2 24 703517W Spring Pin 8 X 55 2 25 3677515 Bush 4 26 3630218 Supper Linkage, Spring 2 27 3637421 Spring 4 28 N/A Lower Linkage Spring 2 29 N/A Screw M12 X 30 Din 933 8.8 2 30 700219C Nut M24 X 3 2 31 3630245 Swinging Pipe 2 32 3637501 Lock Device 2 33 3637502 Lever 8 34 3638402 Snap Ring E 15 Din 471 16 35 3637503 Pin 8 36 3638601 Pin 8 37 3630250 Main Pipe 2 38 3630105 RH Wheel Arm 3 38A 3630106 LH Wheel Arm 3 39 3736800 Seal 12 40 3736000 Bearing 30205 12 41 3637504 Wheel Hub 12 42 3736001 Bearing 30204 12 43 N/A Nut M18 X 1,5 12 44 3736700 Safety Cap 12 45 3637505 Flange 12 46 3637506 Rim 12 47 3737507 Tine 0,276" -7mm 480 48 3637508 Tine Clamp 120 49 N/A Screw M10 X 25 Din 603 6.8 240 50 00765676 Nut M10 Din 980 240 51 61368C8 Screw M10 X 25 Din 933 8.8 120 52 00755954 Spring Washer 10,5 Din 127b 120 53 3637509 Spindle-Weld-On 12 54 N/A Split Pin 12 55 N/A Nut M14 Din 980 2 56 00755949 Nut M10 Din 934 120 57 3630100 Hub Assembly 12 58 3630101 RH Wheel Assy (Tine 0,276") 6 3630102 LH Wheel Assy (Tine 0,276") 6 19-1-4
BUSH HOG / MATERIAL HANDLING REPAIR PARTS MANUAL HYDRAULIC CYLINDER ASSEMBLY APRIL, 2011 2 5 4 3 1 6 7 1 3667151 Rod 1 2 3667152 Cylinder Tube 1 3 3667153 Cylinder Head 1 4 3667121 Piston 1 5 3667140 Nut 1 6 3667147 Seal Kit 1 7 3667146 Cylinder, Complete 1 19-1-5
BUSH HOG / MATERIAL HANDLING REPAIR PARTS MANUAL CENTER WHEEL KIT APRIL, 2011 1 3690278 Arm, Center Wheel 1 2 3630100 Hub Assembly 1 3 3630102 Wheel Assy., LH 1 4 3660309 Bracket 1 5 3668614 Pulley 1 6 61063c8 Screw M10 X 45 4 7 3667599 Wheel Support Hitch Block 4 8 N/A Screw M18 X 100 1 9 N/A Top Locknut 1 10 3667412 Cable 1 11 00762363 Bolt 4 12 00755949 Nut 4 13 00754517 Screw 1 14 3668417 Clamp, Wire Rope Cable 2 15 3668416 Thimble 2 16 3637506 Rim 1 17 N/A Carriage Bolt 20 18 3637508 Tine Clamp 10 19 3637505 Flange 1 20 00755949 Nut 20 21 3737507 Tine 40 22 3637509 Spindle, Weld-On 1 23 3736800 Seal 1 24 3736000 Bearing Set, Inner 1 25 N/A Cotter Pin 1 26 3637504 Hub 1 27 3736001 Bearing Set, Outer 1 28 N/A Nut 1 29 N/A Hub Cap 1 30 N/A Bolt 6 31 00755954 Lockwasher 6 32 00755949 Nut 6 33 3667529 Bushing 1 34 N/A Nut 1 35 3660310 Hook Spindle Arm 1 36 3668420 Clevis Yoke 1 19-1-6
BUSH HOG / MATERIAL HANDLING REPAIR PARTS MANUAL DECALS - SAFETY AND MARKING APRIL, 2011 REF. PART DESCRIPTION QTY. NO. NO. REQ D. 1 999001 Warning - Multi-Hazard 1 2 00786980 Use Genuine Bush Hog Parts 1 3 00763977 Information Notice To Owner 1 4 50058089 Bush Hog Logo 2 5 5W119 Warning Speed Restriction 1 6 03200347 Reflector - Smv Sign 1 7 02962764 Warning - Pinch Points 4 8 00756059 Warning - Oil Leak 3 9 3668308 Warning - Install Transport Lock When In Transport 2 10 02962765 Warning - Multi-Hazard 2 11 2738333 Reflector - Yellow Oblong Reflector 4 12 N/A Serial Plate 1 13 999200 Warning - To Avoid Serious Injury Or Death 1 14 00725746 Peligro Spanish Translation 1 15 50068828 Logo - Ewr Model Name 2 16 2738332 Reflector - Red Oblong Reflector 2 17 00776031 Canister, Operator s Manual (Inside) 1 18 50068753 Operator s Manual 1 19-1-7
2501 Griffin Ave. Selma, AL 36703 (334) 872 6261 (334) 874 2700 Parts Ordering 1 800 304 2836 Fax 1 800 572 1784 www.bushhog.com