PFT-61 LH & RH Sidelite Transom Patch Fitting w/stop & Fin Installation Instructions For Installation Assistance, Call 855.594.6989 www.assaabloyglass.us Tools Needed: Torque Wrench and Bit Screwdriver (Phillips) 5mm Hex Wrench 4 3 /16" (106) 4 3 /16" (106) 2 1 /16" (52) Fin Panel Side Panel Top Panel NOT TO SCALE Parts Included 2 1 /16" (52) Exterior View PFT-61RH } Bracket Cover Plate PFT-61LH Cover Plate } Bracket z Cover Plate { Screws (3) w Bushings (5) u Cover Plate w Bushings (5) u Cover Plate { Screws (3) y Screws (5) v Bracket PFT-61RH Parts List 1 Cover Plate 2 Bracket 3 Bushings (5) 4 Bracket 5 1 1 /16" - M6 x 27 Screws (5) 6 Cover Plate 7 3 /4" - M4 x 20 Phillips Head Screws (3) 8 Cover Plate 9 Bracket z Cover Plate y Screws (5) v Bracket PFT-61LH Parts List 1 Cover Plate 2 Bracket 3 Bushings (5) 4 Bracket 5 1 1 /16" - M6 x 27 Screws (5) 6 Cover Plate 7 3 /4" - M4 x 20 Phillips Head Screws (3) 8 Cover Plate 9 Bracket without the express written permission of ASSA ABLOY Inc. is prohibited. PFT-61-06/17
1. Prepare the Glass USE FABRICATION SKETCH TO CUT AND DRILL GLASS. Cut away glass (shaded area) along dotted line to match sketch dimensions. Drill five 13 /16" (20 mm) diameter holes. NOT TO SCALE DIMENSIONS IN INCHES (MILLIMETERS) rad. 7 / 16 " (11) 2 3 /8" (60) 1 3 /16" (30) Fin Panel 7 / 16 " (11) 1 3 / 16 " (30) 1 3 / 4 " (45) 1 / 8 " (3) Top Panel Sketch shown for RIGHT HAND. Flip horizontal for LEFT HAND preparation. 2 7 / 8 " (73) 1 / 8 " (3) Side Panel Caution: Office copiers, printers and facsimile machines may change the size of a drawing and make it inaccurate to use as a template. without the express written permission of ASSA ABLOY Inc. is prohibited. PFT-61-06/17 2
2. Attach Fin to Support Bracket (following diagrams show RIGHT HAND bracket) Make sure the surface is thoroughly cleaned and remove all screws. Attach Bracket 11 to Bracket x with Screws { using screwdriver ensuring that the bushing side of Bracket x is facing the glass. { Screws (3) 3. Fasten Support Brackets Make sure the surface is thoroughly cleaned and remove all screws. Insert three Bushings w into prepped 13 /16" (20 mm) diameter holes to join Brackets v & x. Place Bracket x into prepped area of glass, join Bracketv from the other side. Insert two Screws y into holes and tighten with 5mm hex wrench to hold Brackets together. Do not tighten completely to allow for adjustments throughout installation. Insert Screw y into Bracket v, align fitting to desired position. Torque three Screws y to 12 nm. w Bushings y Screws 5 mm Hex Wrench v Bracket without the express written permission of ASSA ABLOY Inc. is prohibited. PFT-61-06/17 3
4. Adhere Cover Plates Remove adhesive strip paper on both Brackets v & x to adhere Cover Plates u & z. Hook Cover Plates u & z over hinge side locking pins. Push in spring loaded locking pin on opposite side of Bracket. Snap on Cover Plates. z Cover Plate u Cover Plate 5. Install Fin Insert two Bushings w into prepped 13 /16" (20 mm) diameter holes to join Brackets } & 11. Place Bracket 11 into prepped area of glass, join Bracket } from the other side. Insert Screw y into hole and tighten with 5mm hex wrench to hold Brackets together. Do not tighten completely to allow for adjustments throughout installation. Insert Screw y into Bracket }, align fitting to desired position. Torque both Screws y to 12 nm. w Bushings } Bracket y Screws without the express written permission of ASSA ABLOY Inc. is prohibited. PFT-61-06/17 4
6. Adhere Cover Plates Remove adhesive strip paper on both Brackets } & 11 to adhere Cover Plates & 10. Hook Cover Plates & 10 over hinge side locking pin. Push in spring loaded locking pin on top and bottom of Bracket. Snap on Cover Plates. Cover Plate without the express written permission of ASSA ABLOY Inc. is prohibited. PFT-61-06/17 5
www.assaabloyglass.us USA: ASSA ABLOY Glass Solutions Rockwood, PA 15557 Phone: 855.594.6989 without the express written permission of ASSA ABLOY Inc. is prohibited. PFT-61-06/17