LAW ENFORCEMENT VEHICLE EQUIPMENT 2926 Yelm Hwy SE - Olympia, WA 98501 PH (360) 491-6197 TF 1-800-426-2627 FAX (360) 459-0729 Cover Seat/ CAREFULLY READ INSTRUCTIONS BEFORE BEGINNING INSTALLATION. #12 PARTITION ALWAYS CHECK PARTS LIST FOR FUEL LINES, BRAKE LINES, WIRING OR ANY OBSTRUCTIONS BEFORE DRILLING ANY HOLES! TO AVOID TAMPERING WITH FASTENERS ALWAYS PLACE WASHER AND NUTS AWAY FROM THE GUARDED AREA!!! INSTALL THE SETINA SEAT PRIOR TO INSTALLING THE PARTITION. NOTE: SEAT BELT RETRACTORS ARE EQUIPPED WITH AN ORANGE/RED STOP FORK. DO NOT REMOVE UNTIL BELT IS FULLY INSTALLED. IF REMOVED DO NOT ALLOW BELT TO RETRACT PAST THAT POINT. COVER SEAT PARTS LIST 8 17 17 16 4 4 19 17 1 19 5 20 7 2 18 6 AP9174 - CENTER RETRACTOR ASSEMBLY ITEM QTY PART # DESCRIPTION 3 9 1 0115155 7/16 x 1 Bolt (not pictured) 10 4 0115159 7/16-20 x 1.5 Bolt (not pictured) 11 4 10404-02828 1/4 USS Fender Washer (not pictured) ITEM QTY PART # DESCRIPTION 1 1 SP9133 Setina Seat 2 1 SP8834 Lower Seat Belt Port - Cover 3 2 SP8857 End Release Partition - Buckle 4 2 SP8965 Rear Seat - Upper Seat Belt Port - Cover 5 1 SP9124 Lower Cover Bracket 6 2 SP12423 Twin Wire Seat Buckle 7 1 SPW9125 Lower Seat Belt Mount Bracket - Weldment 8 1 SP9123 Rear Deck Cover 12 10 1133816 7/16 Washer SEA Hard YZ (not pictured) 13 2 24072 5/16-18 x 1 1/4 BHSCS (not pictured) 14 5 37186 7/16 Nylock (not pictured) 15 2 37556 5/16 Nylock (not pictured) 16 1 SP9142 Center Retractor Stud - Strap Bracket 17 3 SP9143 Rear Deck Bracket - Washer Plate 18 1 SP9162 Pinch Weld Backing Plate 19 2 SP9631B Charger Seat Retractor S2931-001 20 1 SPW9147 Upper Retractor Mount Bracket - Weldment PAGE 1
Cover Seat/ IMPORTANT: BOLT BAG MAY CONTAIN EXTRA FASTENERS BOLT BAG BB9175 ITEM QTY PART # DESCRIPTION 1 2 0115159 7_16-20 x 1.5 Bolt 1 2 2 2 PB2781.5 Outer Spacer 3 2 10404-02824 1/4 Dome Cap 4 2 10404-02789 1/4 Wizlock 5 4 0162317 8mm x 1.25mm Hex Flg Nut 6 2 25C125KTCYO/ON PIN 1/4 x 1.25 THSCS 3 4 5 7 2 37186 7/16 Nylock 8 4 1172906 #6 x.75 Phillips Pan Head SMS 9 4 0149083 1/4 x 1 Phillips SMS 10 4 25C75KTCYO-NO PIN 1/4 x 3/4 THSCS 11 4 1133816 7/16 Washer SEA Hard YZ 6 7 12 5 0162638 1/4 Panel Retainer 13 10 10404-02791 1/4 Fender Washer 8 9 10 11 12 13 PAGE 2
Cover Seat/ Figure 1 STEP 1 Figure 2 STEP 2 SEAT BELT GUIDE PRY BAR FOR SEAT CLIP STEP 1 - Instructions Begin by removing the rear seat, back rest and rear deck cover from the vehicle, use a piece of flat bar that is 7 to eject the clips on the back rest). Repeat for passenger side. Remove the lower factory seat belt buckles. SEE FIGURE #1 STEP 2 - Instructions Remove the C pillar cover from the vehicle, (the seat belt guide will need to be notched and removed in order to free the belt form the C pillar). Repeat for passenger side. SEE FIGURE #2 Figure 3 STEP 3 Figure 4 STEP 4 ZIP TIED FACTORY SEAT BELT.5 SPACER BUCKLE STEP 3 - Instructions STEP 4 - Instructions Roll and zip tie the factor seat belts in place. See Figure #3. Return the C pillar cover. Repeat for passenger side. SEE FIGURE #3 Place the 1/2 spacer between the lower buckle and the vehicle s sheet metal. Secure to the factory mount point using a 7/16 x 1.5 fastener with washer. Repeat for passenger side. SEE FIGURE #4 PAGE 3
Cover Seat/ Figure 5 STEP 5 Figure 6 STEP 6 RETRACTOR ASSEMBLY CENTER FACTORY RETRACTOR STRAP BRACKET REAR DECK MOUNT HOLES 2 OF 3 STEP 5 - Instructions STEP 6 - Instructions Remove and store the factory center retractor from the vehicle. Drill out the (3) existing mount holes on the rear deck located behind child anchors using a 7/16 drill bit. SEE FIGURE #5 Remove the (3) washer plates from the center retractor assembly. Rotate the strap bracket and place over the factory center retractor stud. SEE FIGURE #6 Figure 7 STEP 7 Figure 8 STEP 8 RETRACTOR BRACKET WASHER PLATES PINCH WELD W/BACKING PLATE STEP 7 - Instructions Secure the retractor mount bracket weldment and washer plates to the rear deck using the provided 7/16 x 1.5 bolts, 7/16 washer (on both sides) and 7/16 nyloc nuts. SEE FIGURE #7 STEP 8 - Instructions Move to the lower portion where the retractor bracket meets the pinch weld. Drill the (2) mount points using 21/64 drill bit. Place the backing plate on the backside. Secure using the provided 5/16 x 1.25 bolt, 1/4 USS fender washer (on both sides) and 5/16 nyloc nuts. Return the backrest to the vehicle. SEE FIGURE #8 PAGE 4
Cover Seat/ Figure 9 STEP 9 Figure 10 STEP 10 LOWER SEAT MOUNTING BRACKET STEP 9 - Instructions Secure the lower cover bracket to the riv nuts on the seat belt mount bracket weldment using the provided 1/4 x 3/4 bolts. Place the lower bracket weldment over the existing studs and secure with the existing fasteners. SEE FIGURE #9 STEP 10 - Instructions Using a tie down, synch the Setina seat and move it into the vehicle. Lean the seat forward. SEE FIGURE #10 Figure 11 STEP 11 Figure 12 STEP 12 UPPER PORT OPENING STEP 11 - Instructions Return the factory seat to the vehicle. Tucking the center portion under the lower seat bracket weldment. SEE FIGURE #11 STEP 12 - Instructions Thread the center retractor seat belts through the upper port openings. SEE FIGURE #12 PAGE 5
Cover Seat/ Figure 13 STEP 13 Figure 14 STEP 14 8MM HEX FLANGE NUT SEAT BELT END STEP 13 - Instructions Adjust the seat so the rear deck portion slides over the existing studs. Secure the seat loosely to the rear deck using the 8mm x 1.25 Hex Flange nut. SEE FIGURE #13 STEP 14 - Instructions Secure the seat belt end to the studs on the lower bracket weldment, using the 7/16 nyloc and 7/16 washer. NOTE: The socket will get stuck. Use channel locks to pull it out. SEE FIGURE #14 Figure 15 STEP 15 Figure 16 STEP 16 LOWER COVER LOWER PHILLIPS SMS STEP 15 - Instructions Place the lower cover over the lower port opening and secure using the provided 1/4 x 1.25 bolt with 1/4 fender washer. SEE FIGURE #15 STEP 16 - Instructions Move to the lower portion of the seat. Drill the (4) mounting points into the vehicle using a 7/32 drill bit. Secure using the provided 1/4 x 1 Phillips SMS with 14 fender washers. Repeat for passenger side. SEE FIGURE #16 PAGE 6
Cover Seat/ Figure 17 STEP 17 Figure 18 STEP 18 UPPER PORT COVERS ROCKER MOLDING STEP 17 - Instructions STEP 18 - Instructions Slide the seat belt through the upper port covers and secure to Setina seat using the provided #6 x 3/4 SMS. SEE FIGURE #17 Notch the rocker molding as shown in figure #18. NOTE: Make adjustments as needed to fit around the seat. NOTE: Driver side shown. SEE FIGURE #18 Figure 19 STEP 19 Figure 20 STEP 20 Figure 21 STEP 21 ROCKER MOLDING IN VEHICLE TPO REAR DECK COVER END RELEASE BUCKLE STEP 19 - Instructions STEP 20 - Instructions STEP 21 - Instructions Return the rocker molding to the vehicle. Repeat for passenger side. NOTE: Driver side shown. SEE FIGURE #19 Set the TPO rear deck cover into place. Secure to the seat using the 1/4 black plugs. SEE FIGURE #20 Align the parking buckle to the lower mounting hole on the mount plate. Secure using the provided 1/4 x 3/4 fastener, 1/4 fender washer (on both sides) and 1/4 wizlocks. Place dome caps over wizlocks. SEE FIGURE #21 PAGE 7