Superstrut fittings and brackets are man u fac tured from hot rolled carbon steel. Dimensions The following standard dimensions apply to all fittings except as indicated on the individual drawings. Hole spacing 13/16 in. from end of fittings Hole spacing 1-7/8 in. centers Hole size 9/16 in. diameter 1-5/8 in. wide 1/4 in. thick Application Instructions Parts drawings illustrate a typical use for the fitting, and in many cases other uses for the part are appropriate. Design Data Load ratings vary depending fittings and brackets are used with 1, 14 or 16 gauge channel. Ratings are shown for each channel material. (See page A57 for Engineering Data and Specifications). Nuts and Bolts Required Unless otherwise noted, nuts and bolts for use with fittings and brackets should be ordered separately. The standard bolt for the 9/16 in. hole is a 1/ in. hex head cap screw 1 in. long. The 1 in. length may be used with all Series channel. Design Load For more information on design load, see page A57 Engineering Data and Specifications. Finishes and Special s Standard finishes are Hot Dipped Galvanized (HDGC) and GoldGalv (no suffix). Fittings are also available in (EG) and Stainless Steel 316 (SS6C). Contact your Regional Sales Office for availability and minimum quantities. Aluminum channel For Aluminum channel, we suggest fittings in HDG (C) or SS6 (C). A13
Flat Fittings AB06 AB07 X07 AB06HDGC AB06EG AB06 AB06SS6C Wt./C 35 lb. AB07HDGC AB07EG AB07 AB07SS6C Wt./C 5 lb. X07HDG X07EG X07 X07SS6 Wt./C 78 lb. X08 AB19 AB0 X08HDG X08EG X08 X08SS6C Wt./C 88 lb. AB19HDGC AB19EG AB19 AB19SS6C Wt./C 53 lb. AB0HDGC AB0EG AB0 AB0SS6C Wt./C 78 lb. AB40 AB41 AB4 AB40HDG AB40EG AB40 Wt./C 69 lb. C EG GoldGalv SS6C Cat. No. Bolt Size (in.) AB41-1/4* 1/4 18 AB41-5/16* 5/16 18 AB41-3/8* 3/8 18 AB41-1/* 1/ 17 AB41-5/8* 5/8 15 AB41-3/4* 3/4 14 Wt./C lb. AB4HDGC AB4EG AB4 Wt./C 9 lb. For use with either 3/8 in. or 1/ in. hanger rod. AB53 AB55 AB57 AB53HDGC AB53EG AB53 AB53SS6C Wt./C 97 lb. AB55HDGC AB55EG AB55 Wt./C 70 lb. AB57HDGC AB57EG AB57 Wt./C 105 lb. AB61 AB63 AB65 AB61HDGC AB61EG AB61 Wt./C 148 lb. AB63HDGC AB63EG AB63 AB63SS6 Wt./C 150 lb. AB65HDGC AB65EG AB65 Wt./C 105 lb. s (No suffix) GoldGalv A14
90º Fittings AB01 AB0 AB01HDGC AB0HDGC AB01EG AB0EG AB01 AB0 AB01SS6C AB0SS6C Wt./C 35 lb. Wt./C 35 lb. AB03 AB03HDGC AB03EG AB03 AB03SS6C AB04 AB05 AB13 AB04HDGC AB05HDGC AB13HDGC AB04EG AB05EG AB13EG AB04 AB04SS6 AB05 AB05SS6C Wt./C 78 lb. AB13 Wt./C 15 lb. AB14 AB14HDGC AB14EG AB16 AB16HDGC AB16EG AB5 C GoldGalv EG AB14 AB14SS6 Wt./C 15 lb. AB16SS6C Wt./C 135 lb. Cat. No. A (in.) Wt./C lb. AB5-1* 3-7/8 61 AB5-* 5-7/8 84 AB5-3* 7-7/8 107 AB5-4* 9-7/8 130 AB54R AB54L AB60R AB54RHDGC AB54LHDGC AB60RHDGC AB54REG AB54LEG AB60REG AB54R Wt./C 105 lb. AB54L Wt./C 105 lb. AB60R AB60L AB74 AB75 AB60LHDGC AB74HDG AB75HDGC AB60LEG AB74EG AB75EG AB60L AB74 Wt./C 70 lb. AB75SS6C Wt./C 77 lb. s (No suffix) GoldGalv A15
90º Fittings AB84R AB84RHDG AB84REG AB84R Wt./C 30 lb. AB84L AB84LHDG AB84LEG AB84L Wt./C 30 lb. AB99 AB99HDG AB99EG AB99 Wt./C 40 lb. X01 X01HDG X01EG X01 Wt./C 65 lb. X04 X04HDG X04EG X04 Wt./C 90 lb. X89 X89HDGC X89EG X89 Wt./C 105 lb. X99 X99HDGC X99EG X99 Wt./C 38 lb. N05 N05HDGC N05EG N05 N05SS6C Wt./C 74 lb. N19 N19HDG N19EG N19 N19SS6 Wt./C 71 lb. s (No suffix) GoldGalv A16
Angular Fittings AB5 AB6 AB7 AB8 AB5HDGC AB5EG AB5 AB5SS6 AB6HDGC AB6SS6 Wt./C 119 lb. AB7HDGC AB7EG AB7 AB7SS6 AB8HDGC AB8SS6C Wt./C 69 lb. Other angles available. Contact your Regional Sales Office. Other angles available. Contact your Regional Sales Office. Other angles available. Contact your Regional Sales Office. Other angles available. Contact your Regional Sales Office. AB31 AB3 AB39 AB31EG AB3EG C GoldGalv EG Cat. No. A (in.) B (in.) Wt./C lb. AB39-1* 7-13/16 8-1/ 148 AB39-* 13-3/4 17 55 AB39-3* 19-3/4 5-1/ 363 Z Shape Fittings A09 B09 C09 A09HDGC A09EG A09 A09SS6 Wt./C 55 lb. B09HDG B09EG B09 Wt./C 43 lb. C09 Wt./C 49 lb. For attaching A and AR Series channel. For attaching B and BR Series channel. For attaching C Series channel. D09 1 " CZ09 EZ09 Wt./C 45 lb. EZ09HDGC EZ09EG EZ09 EZ09SS6 For attaching D Series channel. For attaching H Series and A back to back. For attaching E Series channel. s (No suffix) GoldGalv A17
U Shape Fittings A08 A08HDGC A08EG A08 A08SS6C Wt./C 75 lb. Does not include stud nut or bolts. For A and AR Series channel. A13 Inside Joiner Wt./C 40 lb. For A100 Series. Available only in GoldGalv finish. A10 A10HDGC A10EG A10 A10SS6C Wt./C 88 lb. For attaching A and AR Series channel. A11 A11HDGC A11EG A11 Wt./C 18 lb. For attaching A and AR Series double channel, and H Series. AN11 AN11HDG AN11EG AN11 Wt./C 181 lb. A1 A1HDG A1EG A1 A1SS6 Wt./C 113 lb. B10 B10HDG B10EG B10 B10SS6 Wt./C 65 lb. For attaching B and BR Series. C10 C10HDG C10EG C10 Wt./C 77 lb. For attaching C Series channel. D10 D10HDG D10EG D10 D10SS6 Wt./C 71 lb. For attaching D Series channel. E10 E10HDGC E10EG E10 Wt./C 11 lb. AB45 AB45HDG AB45EG AB45 Wt./C 70 lb. AB88 C GoldGalv EG For attaching E Series channel. For attaching A and AR Series double channel. Cat. No. Bolt Size (in.) Wt./C lb. AB88-3/8* 3/8 AB88-1/* 1/ 37 AB88-5/8* 5/8 s (No suffix) GoldGalv A18
Wing Fittings AW04 AW04HDG AW04EG AW04 Wt./C 76 lb. AW14 AW14HDG AW14EG AW14 Wt./C 115 lb. A17 AW17HDG A17EG A17 Wt./C 155 lb. AW05L AW05R AW15L AW15R AW05LHDG AW05LEG AW05L Wt./C 59 lb. AW05REG AW05R Wt./C 59 lb. AW15LHDG AW15LEG AW15L Wt./C 98 lb. AW15RHDG AW15REG AW15R Wt./C 98 lb. 3 7 / 8 " 3 7 / 8 " AW0 AW0HDGC AW0EG AW0 Wt./C 90 lb. AW4 AW4HDGC AW4EG AW4 Wt./C 147 lb. AW19 AW19HDGC AW19EG AW19 Wt./C 187 lb. AW6 AW6HDG AW6 Wt./C 113 lb. A18 A18HDG A18EG A18 Wt./C 177 lb. AW8 AW8HDG AW8EG AW8 Wt./C 30 lb. s (No suffix) GoldGalv A19
Brackets S0 S03 S49 SS6C Cat. No. A (in.) B (in.) C (in.) Wt./C lb. S0-6* 6 5 75 S0-9* 9 8 100 S0-15* 15 14 8 175 S0-1* 1 0 14 50 S0-7* 7 6 0 35 S0-33* 33 3 6 400 Cat. No. A (in.) B (in.) Design Wt./C lb. S03-8* 8-1/ 4-1/16 180 S03-14* 14-1/ 5-3/8 35 S03-0* 0-1/ 6-11/16 55 100 S03-6* 6-1/ 8 675 S03-3* 3-1/ 8 840 S03-38* 38-1/ 8 1050 Cat. No. A (in.) B (in.) Design Wt./C lb. S49-8* 8-1/ 8 30 S49-14* 14-1/ 9 50 S49-0* 0-1/ 9 660 1500 S49-6* 6-1/ 11-1/ 870 S49-3* 3-1/ 11-1/ 1030 S49-38* 38-1/ 11-1/ 130 S50 S51 S56 SS6C SS6C SS6C Cat. No. A (in.) Design Wt./C lb. S50-6* 6 1500 150 S50-8* 8-1/ 1500 150 S50-1* 1 800 50 S50-14* 14-1/ 800 50 S50-18* 18 550 350 S50-0* 0-1/ 550 350 S50-4* 4 400 450 S50-6* 6-1/ 400 450 May be installed inverted with no change in load ratings. Cat. No. A (in.) Design Wt./C lb. S51-1* 1 1650 514 S51-14* 14-1/ 1650 514 S51-18* 18 1050 714 S51-0* 0-1/ 1050 714 S51-4* 4 800 914 S51-6* 6-1/ 800 914 S51-30* 30 650 1114 S51-3* 3-1/ 650 1114 S51-36* 36 500 1314 S51-38* 38-1/ 500 1314 Cat. No. A (in.) Design Wt./C lb. S56-6* 6 1000 151 S56-8* 8-1/ 1000 151 S56-1* 1 500 51 S56-14* 14-1/ 500 51 S56-18* 18 300 351 S56-0* 0-1/ 300 351 S56-4* 4 50 451 S56-6* 6-1/ 50 451 When installed in inverted position reduce load rating 40%. S47 S47HDG S47 S47SS6 Design Moment (channel upright as shown) When Supported By A-100 550 inch lb. A-1400 3650 inch lb. S48 S48HDGC S48 Design Moment (channel upright as shown) When Supported By A-10 10 800 inch lb. A-140 7550 inch lb. Applies to fitting only, not to the arm. Applies to fitting only, not to the arm. s (No suffix) GoldGalv A0
Brackets S04 S04HDGC S04 Wt./C 174 lb. S05 S05HDGC S05 Wt./C 64 lb. S17 S17HDG S17 S17SS6 Wt./C 64 lb. A-100 750 A-1400 500 A-100 750 A-1400 500 A-100 750 A-1400 650 S18 S18HDG S18 Wt./C 95 lb. S SHDG S Wt./C 385 lb. S6 S6HDG S6 Wt./C 41 lb. A-100 750 A-1400 650 A-100 1000 A-1400 750 A-100 1000 A-1400 750 A1
Post Bases AP3 AP35 AP3HDGC AP35HDGC AP3EG AP35EG AP3 AP35 Wt./C 384 lb. Wt./C 400 lb. AP3SQ AP35SQ AP3SQHDGC AP35SQHDGC AP3SQEG AP35SQEG AP3SQSS6 AP35SQ Wt./C 384 lb. AP35SQSS6 Wt./C 400 lb. AN70 EG TS7 Track Support TS7HDG TS73 Track Support TS73HDG Cat. No. A B Wt./C lb. AN70-1* -3/8 6 113 AN70-* 4-3/8 8 151 AN70-3* 6-3/8 10 199 AN70-4* 8-3/8 1 46 AN70-* 10-3/8 14 93 Requires 3/8 in. x -1/ in. bolt and nut (not included) Design load: 1000 lb. Wt./C 104 lb. For use over channel splice Requires 3/8 in. x -1/ in. bolt and nut (not included) Design load: 000 lb. Wt./C 8 lb. A
Superstrut Special Application TR9 TR94 Can be used for Series A, E and H channels only. Can be used for Series A, E and H channels only. Standard finish is. Standard finish is. Frictionless needle bearings. Frictionless needle bearings. Design load: 500 lb. Design load: 1000 lb. Cast aluminum rollers, steel brackets. Designed for standard saddles. Order separately for each pair of rollers: two 1/ in. x 5/16 in. hex head cap screws and two 1/ in. channel nuts. Space to suit O.D. of pipe and wrapping. Safety factor of 5. Safety factor of 5. Design Load: 350 lb. Wt./C 59 lb. Wt./C 106 lb. Wt./C : 300 lb. C78 Pipe Roller (Pair) Adjustable Universal Support Support building services and access equipment on flat roofs and flat surfaces Riser Kit Cat. No. AUS14-96 AUS-RISER-KIT A100HS100PG H104-1/X10EGC E145-1/EGC E147-1/EGC E148-1/EGC The T&B Adjustable Universal Support (AUS) provides an easy method for supporting pipes, conduit and equipment on flat roofs, below raised floors and even on level ground applications. The AUS reduces installation time compared to other support solutions such as wooden blocks, cement blocks, straps and clips. These labor intensive solutions also increase the danger of roof membrane penetration. The AUS system also allows for tool free adjustment of the pedestal height from 6 to 9 inches with a twist of the wrist. This ensures that the supported objects or pipes are uniformly supported and no high stress supports are carrying a disproportionate load in a single location. w w w. t nb. c a AUS-STRUT-KIT A100HS100PG E14-1/X00EGC E145-1/EGC E147-1/EGC E148-1/EGC Description Ajustable Universal Support (Base only) Qty. 1 Riser Kit 14 in. strut 1 in. threaded rod Nut Washer Lock washer 1 8 8 4 Bolt Kit 14 in. strut Bolt Nut Washer Lock washer 1 4 AUS15PCSS6 4-1/ in. stainless steel 316 strap (to restrain 1-1/4 in. pipe) AUS150PCSS6 5 in. strap (to restrain 1-1/ in. pipe) AUS00PCSS6 6 in. strap (to restrain in. pipe) Bolt Kit Straps Pipe Grooves 1 in. Platform Adjustable Height Jackscrew Locking Mechanism Sturdy Jackscrew Base to Distribute Load Flexible PVC Mat to Eliminate Stress Points A3