NATIONAL OFFICE FURNITURE CASEGOODS 2 21
PRODUCT SPECIFICATIONS WORKSURFACE Laminate surfaces are 13 16" HPL (high pressure laminate) or 11 8" TFL (thermally fused laminate), and feature a softened 3mm PVC rim Refer to page 25 for rim profiles and colors Grain direction runs left-to-right Always sold with base HEIGHT ADJUSTABLE BASES WITH POWERED PHASE 3 SYSTEM Rated for a maximum of 220 lbs. (including surface and other accessories) Adjustable glides are standard Digital readout of position, 4 programmable locations 27 ½" to 43 ½" (without surface) / 28 ½" to 44 ½" (with surface) Power cord for base is 124" long 2 stage telescoping leg Some assembly required All hardware and electrical included Electrical included with powered units. Phase 3 system; 3-circuit/5-wire system. UL Listed in full compliance with National Electric Code (NEC). 1, 2, 3, or hardwire circuit configurations can be selected for the receptacles. Standard-capacity power block, provides back-to-back or single user power, and has 2 receptacles per user. No more than 12 duplexes / 20 amp circuit. Phase 3 system is rated at 20 amps. The duplex receptacles are rated at 15 amp. The wiring consists of 5 wires: 3 hot, 1 neutral, and 1 ground. Hardwire selection will include 2 installed empty back-to-back or single junction boxes Items included with this model: base, worksurfaces, center beam, wire management trough, and electrical Double sided units can be ganged together or used as freestanding units Single sided units have both ganging and non-ganging models Single sided ganging can gang to single or double ganging models Ganging kits are sold separately Alloy adjustable height powered bases can be plugged into themselves. This will take up 1 of the power outlets in the unit automatically Only Underwriters' Laboratory (UL) or Canadian Standards Association (CSA) listed electrical components are used in electrical devices and are so labeled. The customer is responsible for the proper application of products to the local codes under which installation must be made HEIGHT ADJUSTABLE BASES (DOUBLE SIDED, NON-POWERED) Rated for a maximum of 220 lbs. (including surface and other accessories) Adjustable glides are standard Digital readout of position, 4 programmable locations 27 ½" to 43 ½" (without surface) / 28 ½" to 44 ½" (with surface) Power cord for base is 124" long 2 stage telescoping leg Some assembly required Items included with this model: base and worksurfaces Double sided units can be ganged together or used as freestanding units Ganging kits are sold separately HEIGHT ADJUSTABLE BASES (SINGLE SIDED, GANGING, POWERED) Rated for a maximum of 220 lbs. (including surface and other accessories) Adjustable glides are standard Digital readout of position, 4 programmable locations 27 ½" to 43 ½" (without surface) / 28 ½" to 44 ½" (with surface) Power cord for base is 124" long 2 stage telescoping leg Some assembly required Items included with this model: base, worksurface, beam wire management trough, electrical, and feet Ganging kits to gang to single or double sided units sold separately Alloy adjustable height powered bases can be plugged into themselves. This will use 1 of the power outlets in the unit HEIGHT ADJUSTABLE BASES (SINGLE SIDED, GANGING, NON-POWERED) Rated for a maximum of 220 lbs. (including surface and other accessories) Adjustable glides are standard Digital readout of position, 4 programmable locations 27 ½" to 43 ½" (without surface) / 28 ½" to 44 ½" (with surface) Power cord for base is 124" long 2 stage telescoping leg Some assembly required Items included with this model: base, worksurface, beam, and feet Ganging kits to gang to single or double sided units sold separately HEIGHT ADJUSTABLE BASES (SINGLE SIDED, NON-GANGING, NON-POWERED) Rated for a maximum of 220 lbs. (including surface and other accessories) Adjustable glides are standard Digital readout of position, 4 programmable locations 27 ½" to 43 ½" (without surface) / 28 ½" to 44 ½" (with surface) Power cord for base is 124" long 2 stage telescoping leg Some assembly required Items included with this model: base, worksurface, and feet HEIGHT ADJUSTABLE FEET Single sided, freestanding or single sided, ganging - feet must be used and are included with unit If ganging single sided to double sided, with double sided on each side of the single, no foot is required, however, if the single sided unit is at the end of the run, the foot is required Feet are not included in double sided models, but can be ordered separately FIXED HEIGHT BASES WITH POWERED PHASE 3 SYSTEM Adjustable glides are standard Some assembly required All hardware and electrical included Electrical included with powered units. Phase 3 system; 3-circuit/5-wire system. UL Listed in full compliance with National Electric Code (NEC). 1, 2, or 3 circuit configurations can be selected for the receptacles. Standardcapacity power block, provides back-to-back or single power, and has 2 receptacles per user. No more than 12 duplexes/ 20 amp circuit. Phase 3 system is rated at 20 amps. The duplex receptacles are rated at 15 amp. The system supports 3 circuits; 1, 2, 3, or hardwire circuits. The customer must order the coordinating duplex receptacles when wiring to the number of circuits needed. The wiring consists of 5 wires: 3 hot, 1 neutral, and 1 ground. Hardwire selection will include 2 installed empty back-to-back or single junction boxes Items included with this model: base, worksurfaces, center beam, wire management trough, and electrical Only Underwriters' Laboratory (UL) or Canadian Standards Association (CSA) listed electrical components are used in electrical devices and are so labeled. The customer is responsible for the proper application of products to the local codes under which installation must be made Double sided units can be ganged with a start", mid, and end or as freestanding Single sided units have both ganging and non-ganging models Single sided ganging can gang to single or double freestanding, start, or end units Ganging kits are sold separately Wire management cutout (2 ½") is standard on fixed height powered models No other grommet options available on these models FIXED HEIGHT BASES (SINGLE SIDED, GANGING, POWERED) Adjustable glides are standard Some assembly required Items included with this model: base, worksurfaces, beam, wire management trough, and electrical Ganging kits to gang to single sided, double sided freestanding, start, or end must be ordered separately Wire management cutout (2 ½") is standard on fixed height powered models No other grommet options available on these models 22 NATIONAL OFFICE FURNITURE CASEGOODS 2
FIXED HEIGHT BASES (SINGLE SIDED, GANGING, NON-POWERED) Adjustable glides are standard Some assembly required Items included with this model: base, worksurfaces, and beam Ganging kits to gang to single sided, double sided freestanding, start, or end must be ordered separately FIXED HEIGHT BASES (NON-POWERED, NON-GANGING) Adjustable glides are standard Some assembly required Items included with this model: base and worksurface FLOOR POWER ENTRY POLE Can be used on adjustable, fixed single, or double sided bases Attaches to underside of beam, used to conceal power in-feed and data cables Non-supporting and can enter at either end or in between benches at the connection point CEILING POWER/DATA POLE Routes power and data from ceiling access to Alloy units Electrical not included in power pole Do not recommend cutting in the field Must be used on an end of a run Fixed height base model and adjustable height base model available 132" length An optional 288" power entry whip ordered separately TACKABLE PRIVACY SCREEN - EDGE MOUNTED Privacy screens are 7 8" thick dual sided fabric Privacy screen holders are 12 gauge steel Privacy screens are not intended to be stand alone units For use with Alloy height adjustable units and single fixed units Screen extends 18" above the surface and 3 ½" below the surface TACKABLE PRIVACY SCREEN - BEAM MOUNTED Privacy screens are 7 8" thick dual sided fabric Privacy screens are not intended to be stand alone units For use with height adjustable and fixed height benching units Screen extends 18" above the surface RESIN PRIVACY SCREEN For fixed models only Mounts in track on beam Track available in Designer White, Cinder, or Platinum Metallic Screens are 3 16" thick 13" high and 18" high options MONITOR ARM - BEAM MOUNTED Features 4D adjustment; adjusting in and out, up and down, swiveling left and right, and tilting back and forward Arm with integrated cable management on single models have a reach of 20" and 10" on height adjustment Single monitor arm supports 1 monitor up to 20 lbs. VESA plates are 100mm x 100mm standard. The standard VESA plates are not compatible with Apple monitors Monitor arm is only available in beam mounted application MONITOR ARM - GROMMET MOUNTED Attachment method via bolt through grommet MFlex pole available with single arm or dual arms Fixed/dynamic arm Pole height 12"; monitor rotation - port/landscape 30" each side; monitor extension 21 1 5" and tilt adjustment 25 + or ; arm height adjustment - 10" dynamic, 8" manual 20 lb. weight capacity per monitor VERTICAL WIRE MANAGER Flexible nylon; available in black, white, and silver Can be used on powered adjustable height double sided bases Attaches to underside of worksurfaces; used to conceal power and data cables ADJUSTABLE HEIGHT SINGLE SIDED BASE VERTICAL WIRE MANAGER Flexible nylon; available in black, white, and silver Can be used with adjustable height single sided bases to conceal wires to the floor Attaches to underside of worksurfaces; used to conceal power and data cables DATA CUTOUTS Data jack covers and blanks not provided by National There is 1 data and 2 electrical cutouts per side in the horizontal wire manager Recommended use with Leviton Quickport Decora Inserts - Decora inserts accept all Quickport snap-in modules INSERTS http://www.leviton.com/oa_html/sectiondisplay.jsp?section=39381&minisite =10251 Black inserts: 80414-W White QuickPort Decora Multimedia Insert 80414-GY Grey QuickPort Decora Multimedia Insert 80414-E Black QuickPort Decora Multimedia Insert 1 port inserts: 41641-W White QuickPort Decora Multimedia Insert 41641-GY Grey QuickPort Decora Multimedia Insert 41641-E Black QuickPort Decora Multimedia Insert 2 port inserts (most common): 41642-W White QuickPort Decora Multimedia Insert 41642-GY Grey QuickPort Decora Multimedia Insert 41642-E Black QuickPort Decora Multimedia Insert ETHERNET PORTS http://www.leviton.com/oa_html/sectiondisplay.jsp?section=39138&minisite =10251 Any connector under this category will work AV PORTS http://www.leviton.com/oa_html/sectiondisplay.jsp?section=67286&minisite =10251 Any connector under this category will work FIBER PORTS http://www.leviton.com/oa_html/sectiondisplay.jsp?section=39161&minisite =10251 Any connector under this category will work NATIONAL OFFICE FURNITURE CASEGOODS 2 23
METAL STORAGE PRODUCT SPECIFICATIONS PEDESTALS AND MOBILE PEDESTALS Leveling glides with 1¾" of adjustment featured on all units except mobile pedestals Powder coated paint Counterweights included Mobile pedestals with cushions have a weight limit of 200 lbs. max DRAWERS 5 8" thick drawer front consists of 22-gauge cold-rolled steel Silencing bumpers ensure quiet drawer operation Cinder steel drawer interiors Drawer body consists of 22-gauge cold-rolled steel Drawers cannot be bottom loaded See interior drawer dimensions below DRAWER PULLS Available in 3 styles, refer to page 25 for styles and colors Full overlay drawers on all cabinets unless otherwise noted DRAWER SUSPENSION File drawers have full extension, progressive action slides with precision steel ball bearings Box drawers have full extension slides with ball bearing rollers All suspensions have a lifetime warranty FILING See filing capabilities below LOCKING Black and silver lock cores are available Key Random means lock cores/keys are randomly (1-5) picked and factory installed in unit Key Specific means you can pick any number (1-200) for black or (1-50) for silver lock core/key. Must specify the lock core model separately; not factory installed and will ship separately Specify a change key to remove and change lock cores To order key specific lock cores, change keys, and master keys, reference page 660 CONSTRUCTION VERTICAL STORAGE 2¼" glide adjustment Units made of 18-gauge cold-rolled steel Backs and sides finished Drawer bottoms not intended to be used as main support for storage items Wardrobe has 2 coat hooks and an adjustable shelf with ½" of adjustment All locker models have 3 lockers 42" tall units intended to match Alloy units with privacy panels (13") 53" tall units intended to match Alloy units with privacy panels (23") and to other WaveWorks storage units DRAWER INTERIOR DIMENSIONS FRONT-TO-BACK DESCRIPTION WIDTH DEPTH HEIGHT FILING CAPABILITIES Box Drawers (24" depth models) 123 16" 20" 35 8" N/A File Drawers (24" depth models) 123 16" 20" 103 16" Letter front-to-back Box Drawers (18" depth models) 123 16" 1515 16" 35 8" N/A File Drawers (18" depth models) 123 16" 1515 16" 103 16" Letter front-to-back 24 NATIONAL OFFICE FURNITURE CASEGOODS 2
CONFIGURATION OPTIONS - RIM PROFILE OPTIONS Softened PVC (V) METAL CHASSIS PAINT COLORS 405 Designer White 419 Wallaby 425 Shadow 440 Cloud 461 Graphite 462 Cinder 485 Dark Chocolate 488 Frosty White 501 Platinum Metallic* 503 Satin Nickel Metallic* 504 Taupe Metallic* 505 Satin Bronze Metallic* *10% List Upcharge LOCKING KEY RANDOM KRB Black KRS Silver PVC SOFTENED RIM AC2 Autumn 2 AD Almond CL Caramel CW Cordovan DW Judicial HN2 Honey 2 IM Brighton MC Amber MH Mocha NM Natural PB Portobello PT Portico SK Skyline SM Sonoma TF Truffle KEY SPECIFIC KS1B Black, 1 lock per unit KS1S Silver, 1 lock per unit KS2B Black, 2 locks per unit KS2S Silver, 2 locks per unit KS3B Black, 3 locks per unit KS3S Silver, 3 locks per unit Unit list price will be reduced by $ 15 per lock when selecting Key Specific option. Must order specific lock cores separately ($ 15 list each). See page 660 for Key Specific model numbers. 405 Designer White 417 Mojave 418 Mouse 419 Wallaby 425 Shadow 440 Cloud 461 Graphite 462 Cinder 478 Platinum Grey 488 Frosty White 491 Designer White Linear 492 Cinder Linear 791 Palisander 792 Sable 793 Acorn PULL OPTIONS Integrated (5) Beam (87) 87SN Satin Nickel Metallic 87MB Cinder 87PL Platinum Metallic (Boring Pattern 128mm) Malibu (7) 7SN Satin Nickel Metallic 7MB Cinder 7PL Platinum Metallic (Boring Pattern 128mm) NATIONAL OFFICE FURNITURE CASEGOODS 2 25
- CONFIGURATION OPTIONS GROMMET OPTIONS If no grommet is desired, specify an X (No Grommet) Round Grommet, Black Nylon $25 list for each grommet G1L Left G1R Right G1LR Left & Right G1C Center Racetrack Grommet, Cinder 1¾" 2¾" 47 32" Cutout Option for 1 Touch Pivoting Power Grommet $25 list upcharge per cutout location CUT-G17L Left 5" CUT-G17R Right CUT-G17LR Left & Right CUT-G17C Center Reference below for cutout locations of CUT-G17 3 ¾" $30 list for each grommet G11MBL Left G11MBR Right G11MBLR Left & Right G11MBC Center Racetrack Grommet, Platinum Metallic $30 list for each grommet G11PLL Left G11PLR Right G11PLLR Left & Right G11PLC Center 223 32" 223 32" 47 32" NACG17AELPGB, NACG17AELPGS, and NACG17AELPGW (Sold Separately) NACG17BELPGB, NACG17BELPGS, and NACG17BELPGW (Sold Separately) NACG17AELPDIQ18B, NACG17AELPDIQ18S, NACG17AELPDIQ18W, NACG17AELPDIQ1B, NACG17AELPDIQ1S, NACG17AELPDIQ1W, NACG17AELPDIQ2B, NACG17AELPDIQ2S, and NACG17AELPDIQ2W (Sold Separately) Reference page 79A for pricing and details NACG17CELPGB, NACG17CELPGS, and NACG17CELPGW (Sold Separately) Reference pages 78-79 for pricing and details NACG17BELPDIQ18B, NACG17BELPDIQ18S, NACG17BELPDIQ18W, NACG17BELPDIQ1B, NACG17BELPDIQ1S, NACG17BELPDIQ1W, NACG17BELPDIQ2B, NACG17BELPDIQ2S, and NACG17BELPDIQ2W (Sold Separately) Reference page 79B for pricing and details NACG17CELPDIQ18B, NACG17CELPDIQ18S, NACG17CELPDIQ18W, NACG17CELPDIQ1B, NACG17CELPDIQ1S, NACG17CELPDIQ1W, NACG17CELPDIQ2B, NACG17CELPDIQ2S, and NACG17CELPDIQ2W (Sold Separately) Reference page 80 for pricing and details 26 NATIONAL OFFICE FURNITURE CASEGOODS 2
CONFIGURATION OPTIONS - 121 8" 121 8" 33 16" 37 8" Left Center Right 6¼" 2½" 6¼" 22¼" for 24" models 28¼" for 30" models Grommet options are available on adjustable height powered, adjustable height non-powered, and fixed height non-powered For double tables, the grommet location consists of the same grommets on both surfaces (upcharge will reflect double grommets) Wire management cutout standard on fixed height powered models. No other grommet options available on these models METAL SPACER CUTOUT OPTIONS If no cutout is desired, specify an X (No Cutout) $ 25 list for each cutout CT1 Cutout, for Adjustable Height CT2 Cutout, for Fixed Height CIRCUIT OPTIONS (POWERED MODELS ONLY) 1 Circuit 1 2 Circuit 2 3 Circuit 3 H Hardwire (Chicago Code) 81 8-wire, Circuit 1 82 8-wire, Circuit 2 83 8-wire, Circuit 3 84 8-wire, Circuit 4 $ 500 list upcharge for the 4 circuit/8 wire option NATIONAL OFFICE FURNITURE CASEGOODS 2 27
- CONFIGURATION OPTIONS LAMINATE WORKSURFACES WOODGRAIN LAMINATE SOLID LAMINATE AC2 Autumn 2 405 Designer White AD Almond 417 Mojave CL Caramel 418 Mouse CW Cordovan DW Judicial HN2 Honey 2 419 Wallaby 425 Shadow 440 Cloud IM Brighton 461 Graphite MC Amber MH Mocha NM Natural 462 Cinder 478 Platinum Grey 488 Frosty White PB Portobello 491 Designer White Linear PT Portico 492 Cinder Linear SK Skyline SM Sonoma TF Truffle 791 Palisander 792 Sable 793 Acorn CSL available; see page 9 for program details and upcharge PATTERN LAMINATE 809 Tungsten Evolv 814 White Tigris 818 Crisp Linen 819 Flax Gauze 820 Paloma Bisque 821 Elemental Concrete 822 Smoke Quarstone 874 Bronze Legacy BEAM PAINT COLOR 21 White 22 Silver 23 Black BASE PAINT COLOR 21 White 22 Silver 23 Black FABRIC PRIVACY SCREEN HOLDER PAINT COLOR 21 White 22 Silver 23 Black PRIVACY SCREEN FABRIC OPTIONS Dune (Grade A) 100% Polyester 8600 Drift 8601 Windblown 8602 Erosion 8603 Haze 8604 Kamelos 8606 Pebble 8607 Gecho 8608 Nectar 8610 Clear Sky 8614 Basin 8615 Raven 8620 Darkness 8621 Golden Repetition (Grade A) 100% Pre-Consumer Recycled Polyester 3700 Ash 3703 White 3705 Willow 3709 Java 3713 Stainless 3715 Almond 3721 Reed 3744 Tawny 3775 Grey Green COM (Grade B) Pact (Grade B) 65% Pre-Consumer Recycled Polyester, 35% Post-Consumer Recycled Polyester 25401 Aloe 25402 Azure 25403 Calla 25404 Coastal 25405 Delft 25406 Dove 25407 Dragon 25408 Eureka 25409 Fern 25410 Harbour 25411 Lily 25412 Lime 25413 Midnight 25414 Nectar 25415 Patina 25416 Putty 25417 Roast 25418 Roma 25419 Rubine 25420 Sketch 25421 Tanzanite 25422 Taupe 25423 Toasty PRIVACY SCREEN RESIN OPTIONS Grade 1 1677 Frosted Grade 2 2877 Ting Ting 2977 Scribble Cloud Grade 3 3377 Wisp Silver RESIN PRIVACY SCREEN HOLDER PAINT COLOR 405 Designer White 462 Cinder 501 Platinum Metallic 27A NATIONAL OFFICE FURNITURE CASEGOODS 2
NATIONAL OFFICE FURNITURE CASEGOODS 2 27B
- FIXED HEIGHT BASE SIZING DOUBLE SIDED FREESTANDING UNITS POWERED PHASE 3 CENTER BEAM NON-POWERED CENTER BEAM SINGLE SIDED FREESTANDING UNITS POWERED PHASE 3 BEAM GANGING (OPTIONAL) FIXED HEIGHT 48" x 48", 54", 60", 66", 72" 60" x 48", 54", 60", 66", 72" DOUBLE SIDED STARTER UNITS POWERED PHASE 3 CENTER BEAM 48" x 48", 54", 60", 66", 72" 60" x 48", 54", 60", 66", 72" NON-POWERED CENTER BEAM 24" x 48", 54", 60", 66", 72" 30" x 48", 54", 60", 66", 72" NON-POWERED, GANGING (OPTIONAL) 24" x 48", 54", 60", 66", 72" 30" x 48", 54", 60", 66", 72" 48" x 48", 54", 60", 66", 72" 60" x 48", 54", 60", 66", 72" 48" x 48", 54", 60", 66", 72" 60" x 48", 54", 60", 66", 72" NON-POWERED, NON-GANGING (NO CENTER BEAM) DOUBLE SIDED MID UNITS POWERED PHASE 3 CENTER BEAM NON-POWERED CENTER BEAM 24" x 48", 54", 60", 66", 72" 30" x 48", 54", 60", 66", 72" 48" x 48", 54", 60", 66", 72" 60" x 48", 54", 60", 66", 72" 48" x 48", 54", 60", 66", 72" 60" x 48", 54", 60", 66", 72" DOUBLE SIDED END UNITS POWERED PHASE 3 CENTER BEAM NON-POWERED CENTER BEAM 48" x 48", 54", 60", 66", 72" 60" x 48", 54", 60", 66", 72" 48" x 48", 54", 60", 66", 72" 60" x 48", 54", 60", 66", 72" 28 NATIONAL OFFICE FURNITURE CASEGOODS 2
ADJUSTABLE HEIGHT BASE SIZING - DOUBLE SIDED GANGING OR FREESTANDING UNITS POWERED PHASE 3 CENTER BEAM NON-POWERED CENTER BEAM 48" x 48", 54", 60", 66", 72" 60" x 48", 54", 60", 66", 72" SINGLE SIDED FREESTANDING UNITS POWERED PHASE 3 BEAM GANGING (OPTIONAL) 48" x 48", 54", 60", 66", 72" 60" x 48", 54", 60", 66", 72" NON-POWERED, GANGING (OPTIONAL) NON-POWERED, NON-GANGING (NO CENTER BEAM) ADJUSTABLE HEIGHT 24" x 48", 54", 60", 66", 72" 30" x 48", 54", 60", 66", 72" 24" x 48", 54", 60", 66", 72" 30" x 48", 54", 60", 66", 72" NOTE: Power will always be in these units strictly for the height adjustability. 24" x 48", 54", 60", 66", 72" 30" x 48", 54", 60", 66", 72" NOTE: Power will always be in these units strictly for the height adjustability. NATIONAL OFFICE FURNITURE CASEGOODS 2 29
- ELECTRICAL Electrical included with powered units are a Phase 3 system; 3-circuit/5-wire system. 1, 2, 3, or hardwire circuit configurations can be selected for the receptacles. Standard-capacity power block, provides back-to-back or single power, and has 2 receptacles per user. Hardwire selection will include 2 installed empty back-to-back or single junction boxes Power entry whips are available in 72", 144" and 288" long and must be ordered separately. The power entry whip has a modular connector at 1 end, attached to a flexible metal conduit with exposed wiring at the other end which is hardwired to the building power. Power entry whips may connect at the end of a run or anywhere within the run, providing power in 1 or both directions Jumpers must be ordered separately and are used to connect power between benches Duplex receptacles are labeled as to the specific circuit they are connected to: I, II, and III CIRCUIT ARRANGEMENT Power Receptacle I II III Hot 1 Black III Circuit label Duplex Neutral White Ground Hot 2 Hot 3 Green/Bare Red Blue Maximum run of double sided powered center beam units on 1 power entry whip is 9 Maximum run of single sided powered beam units on 1 power entry whip is 18 The maximum amount of duplexes that can be used on 1 power entry whip is 36 duplexes. (12) of the 1-circuit, (12) of the 2-circuit, and (12) of the 3-circuit Each double unit has 4 duplexes (2 per side) Each single unit has 2 duplexes (per user) 30 NATIONAL OFFICE FURNITURE CASEGOODS 2
THOUGHT STARTERS ADJUSTABLE HEIGHT - NON-POWERED DOUBLE SIDED CENTER BEAM The overall number of units ganged is only limited based on electrical and floor space. Units can be used as freestanding models or can be ganged together to create a run of units. Ganging kits must be ordered separately. 3 " gap between worksurfaces Worksurface depths in 22 ½" or 28 ½" Widths available in 48", 54", 60", 66", and 72" 1 ½" gap between worksurfaces Depths available in 48" or 60" for double depth bases. Worksurfaces available in HPL or TFL. 6 USER STATION **Image shown above PART NUMBER PART DESCRIPTION PRICE QUANTITY EXT 71N6072AB2NGLL Adjustable Height Base, Double, Non-Powered, Ganging - TFL Top $ 3627 3 $10,881 71NGBK23 Adjustable Ganging Bracket/Cover Kit, Black $ 47 2 $ 94 Total $10,975 10 USER STATION PART NUMBER PART DESCRIPTION PRICE QUANTITY EXT 71N6072AB2NGLL Adjustable Height Base, Double, Non-Powered, Ganging - TFL Top $ 3627 5 $18,135 71NGBK23 Adjustable Ganging Bracket/Cover Kit, Black $ 47 4 $ 188 Total $18,323 12 USER STATION PART NUMBER PART DESCRIPTION PRICE QUANTITY EXT 71N6072AB2NGLL Adjustable Height Base, Double, Non-Powered, Ganging - TFL Top $ 3627 6 $21,762 71NGBK23 Adjustable Ganging Bracket/Cover Kit, Black $ 47 5 $ 235 Total $21,997 Each adjustable height double sided unit must be plugged in separately Center beam mounted and edge mounted privacy screens can be ordered separately Grommet mounted monitor arms can be ordered separately Non-powered double sided adjustable height units ship with the base, top, and center beam support Worksurface grommet cutouts can be selected to add power above the worksurface (see page 26 for grommet selections). The G17A, G17B, or G17C powered grommet must be ordered separately to be installed in the grommet cutout Each worksurface is sized 1½" smaller in width than the model number dimensions to eliminate creep factor and pinch points when ganged together NOTE: Power will always be in these units strictly for the height adjustability NATIONAL OFFICE FURNITURE CASEGOODS 2 31
THOUGHT STARTERS ADJUSTABLE HEIGHT - NON-POWERED SINGLE SIDED BEAM, GANGING The overall number of units ganged is only limited based on electrical and floor space. Units can be used as freestanding models or can be ganged together to create a run of units. Ganging kits must be ordered separately. Worksurface depths in 22 ½" or 28 ½" Widths available in 48", 54", 60", 66", and 72" 1 ½" gap between worksurfaces Worksurfaces available in HPL or TFL. 3 USER STATION PART NUMBER PART DESCRIPTION PRICE QUANTITY EXT 71N2460AB1NGLL Adjustable Height Base, Single, Non-Powered, Ganging - TFL Top $ 1900 3 $ 5,700 71NGBSA23 Adjustable Single Ganging Bracket/Cover Kit, Black $ 225 2 $ 450 Total $ 6,150 6 USER STATION **Image shown above PART NUMBER PART DESCRIPTION PRICE QUANTITY EXT 71N2460AB1NGLL Adjustable Height Base, Single, Non-Powered, Ganging - TFL Top $ 1900 6 $11,400 71NGBSA23 Adjustable Single Ganging Bracket/Cover Kit, Black $ 225 5 $ 1,125 Total $12,525 Each adjustable height single sided unit must be plugged in separately Beam mounted and edge mounted privacy screens can be ordered separately Non-powered single sided adjustable height units ship with the base, top, beam, and feet Worksurface grommet cutouts can be selected to add power above the worksurface (see page 26 for grommet selections). The G17A, G17B, or G17C powered grommet must be ordered separately to be installed in the grommet cutout Grommet mounted monitor arms can be ordered separately Each worksurface is sized 1½" smaller in width than the model number dimensions to eliminate creep factor and pinch points when ganged together Powered single sided ganging models available Feet must be used Ganging bracket/cover kit must be ordered separately NOTE: Power will always be in these units strictly for the height adjustability 32 NATIONAL OFFICE FURNITURE CASEGOODS 2
THOUGHT STARTERS ADJUSTABLE HEIGHT - POWERED DOUBLE SIDED PHASE 3 CENTER BEAM The overall number of units ganged is only limited based on electrical and floor space. Units can be used as freestanding models or can be ganged together to create a run of units. Ganging kits must be ordered separately. Worksurface depths in 22 ½" or 28 ½" Widths available in 48", 54", 60", 66", and 72" 1 ½" gap between worksurfaces Depths available in 48" or 60" for double depth bases. Worksurfaces available in HPL or TFL. 6 USER STATION **Image shown above PART NUMBER PART DESCRIPTION PRICE QUANTITY EXT 71N6072AB2PGLL Adjustable Height Base, Double, Powered, Ganging - TFL Top $ 4457 3 $13,371 71NGBK23 Adjustable Ganging Bracket/Cover Kit, Black $ 47 2 $ 94 71N40VWM23 Vertical Wire Manager $ 132 6 $ 792 71N72ELE Power Entry Whip Hardwire $ 100 1 $ 100 71N22ELJ 22" Ganging Jumper $ 58 2 $ 116 71N7023PVCPFA Edge Mounted Privacy Screen - Railroad, Grade A $ 756 6 $ 4,536 Total $19,009 10 USER STATION PART NUMBER PART DESCRIPTION PRICE QUANTITY EXT 71N6072AB2PGLL Adjustable Height Base, Double, Powered, Ganging - TFL Top $ 4457 5 $22,285 71NGBK23 Adjustable Ganging Bracket/Cover Kit, Black $ 47 4 $ 188 71N40VWM23 Vertical Wire Manager $ 132 10 $ 1,320 71N72ELE Power Entry Whip Hardwire $ 100 1 $ 100 71N22ELJ 22" Ganging Jumper $ 58 4 $ 232 71N7023PVCPFA Edge Mounted Privacy Screen - Railroad, Grade A $ 756 10 $ 7,560 Total $31,685 Electrical included with powered units are a Phase 3 system; 3-circuit/5-wire system. 1, 2, 3, or hardwire circuit configurations can be selected for the receptacles. Standard-capacity power block, provides back-to-back power, and has 2 receptacles per side. Hardwire selection will include 2 installed empty back to back junction boxes Vertical wire managers must be ordered separately and are used to conceal conduit and cables between the worksurface and center beam Ganging jumpers must be ordered separately and are used to jump power from 1 unit to the next Center beam mounted or edge mounted privacy screens can be ordered separately Power entry pole can be used to conceal power to the system. This is sold separately and is used to conceal the data and power cables from the floor to the unit. This is non-supporting and can enter at either end or in between benches at the connection point Horizontal wire manager included with the base model provides a trough for cable to the power/data through tray cut-outs Powered double sided adjustable height units ship with the base, top, center beam support, horizontal wire manager and electrical Grommet cutouts can be selected in the worksurface to add above worksurface power (see page 26 for grommet selections). The G17A, G17B, or G17C powered grommet must be ordered separately to be installed in the grommet cutout Grommet mounted monitor arms can be ordered separately Each worksurface is sized 1½" smaller in width than the model number dimensions to eliminate creep factor and pinch points when ganged together NATIONAL OFFICE FURNITURE CASEGOODS 2 33
THOUGHT STARTERS ADJUSTABLE HEIGHT - POWERED DOUBLE SIDED PHASE 3 CENTER BEAM The overall number of units ganged is only limited based on electrical and floor space. Worksurface depths in 22 ½" or 28 ½" Widths available in 48", 54", 60", 66", and 72" 1 ½" gap between worksurfaces Depths available in 48" or 60" for double depth bases. Worksurfaces available in HPL or TFL. 12 USER STATION PART NUMBER PART DESCRIPTION PRICE QUANTITY EXT 71N6072AB2PGLL Adjustable Height Base, Double, Powered, Ganging - TFL Top $ 4457 6 $26,742 71NGBK23 Adjustable Ganging Bracket/Cover Kit, Black $ 47 5 $ 235 71N40VWM23 Vertical Wire Manager $ 132 12 $ 1,584 71N72ELE Power Entry Whip Hardwire $ 100 1 $ 100 71N22ELJ 22" Ganging Jumper $ 58 5 $ 290 71N7023PVCPFA Edge Mounted Privacy Screen - Railroad, Grade A $ 756 12 $ 9,072 Total $38,023 Electrical included with powered units are a Phase 3 system; 3-circuit/5-wire system. 1, 2, 3, or hardwire circuit configurations can be selected for the receptacles. Standard-capacity power block, provides back-to-back power, and has 2 receptacles per side. Hardwire selection will include 2 installed empty back to back junction boxes Vertical wire managers must be ordered separately and are used to conceal conduit and cables between the worksurface and center beam Ganging jumpers must be ordered separately and are used to jump power from 1 unit to the next Center beam mounted or edge mounted privacy screens can be ordered separately Power entry pole can be used to conceal power to the system. This is sold separately and is used to conceal the data and power cables from the floor to the unit. This is non-supporting and can enter at either end or in between benches at the connection point Horizontal wire manager included with the base model provides a trough for cable to the power/data through tray cut-outs Powered double sided adjustable height units ship with the base, top, center beam support, horizontal wire manager and electrical Grommet cutouts can be selected in the worksurface to add above worksurface power (see page 26 for grommet selections). The G17A, G17B, or G17C powered grommet must be ordered separately to be installed in the grommet cutout Grommet mounted monitor arms can be ordered separately Each worksurface is sized 1½" smaller in width than the model number dimensions to eliminate creep factor and pinch points when ganged together 34 NATIONAL OFFICE FURNITURE CASEGOODS 2
THOUGHT STARTERS ADJUSTABLE HEIGHT - POWERED SINGLE SIDED PHASE 3 BEAM, GANGING The overall number of units ganged is only limited based on electrical and floor space. Units are used as freestanding models or can be ganged together to create a run of units. These can gang to single ganging or double units. Ganging kits must be ordered separately. Worksurface depths in 22 ½" or 28 ½" Widths available in 48", 54", 60", 66", and 72" 1 ½" gap between worksurfaces Worksurfaces available in HPL or TFL. 3 USER STATION **Image shown above PART NUMBER PART DESCRIPTION PRICE QUANTITY EXT 71N2460AB1PGLL Adjustable Height Base, Single, Powered, Ganging - TFL Top $ 2425 3 $ 7,275 71NGBSA23 Adjustable Single Ganging Bracket/Cover Kit, Black $ 225 2 $ 450 71N40VWM23 Vertical Wire Manager $ 132 3 $ 396 71N72ELE Power Entry Whip Hardwire $ 100 1 $ 100 71N22ELJ 22" Ganging Jumper $ 58 2 $ 116 Total $ 8,337 6 USER STATION PART NUMBER PART DESCRIPTION PRICE QUANTITY EXT 71N2460AB1PGLL Adjustable Height Base, Single, Powered, Ganging - TFL Top $ 2425 6 $14,550 71NGBSA23 Adjustable Single Ganging Bracket/Cover Kit, Black $ 225 5 $ 1,125 71N40VWM23 Vertical Wire Manager $ 132 6 $ 792 71N72ELE Power Entry Whip Hardwire $ 100 1 $ 100 71N22ELJ 22" Ganging Jumper $ 58 5 $ 290 Total $16,857 Electrical included with powered units are a Phase 3 system; 3-circuit/5-wire system. 1, 2, 3, or hardwire circuit configurations can be selected for the receptacles. Standard-capacity power block, provides single power, and has 2 receptacles per user. Hardwire selection will include 2 installed empty back to back or single junction boxes Vertical wire managers must be ordered separately and are used to conceal conduit and cables between the worksurface and center beam Ganging jumpers must be ordered separately and are used to jump power from 1 unit to the next Beam mounted or edge mounted privacy screens can be ordered separately Power entry pole can be used to conceal power to the system. This is sold separately and is used to conceal the data and power cables from the floor to the unit. This is non-supporting and can enter at either end or in between benches at the connection point Grommet mounted monitor arms can be ordered separately Horizontal wire manager included with the base model provides a trough for cable to the power/data through tray cut-outs Powered single sided adjustable height units ship with the base, top, beam support, horizontal wire manager, electrical, and feet Each worksurface is sized 1½" smaller in width than the model number dimensions to eliminate creep factor and pinch points when ganged together Feet must be used Ganging bracket/cover kit must be ordered separately NATIONAL OFFICE FURNITURE CASEGOODS 2 35
THOUGHT STARTERS ADJUSTABLE HEIGHT - POWERED SINGLE SIDED PHASE 3 BEAM, GANGING (CONTINUED) The overall number of units ganged is only limited based on electrical and floor space. Worksurface depths in 22 ½" or 28 ½" Widths available in 48", 54", 60", 66", and 72" 1 ½" gap between worksurfaces Worksurfaces available in HPL or TFL. 12 USER STATION PART NUMBER PART DESCRIPTION PRICE QUANTITY EXT 71N2448AB1PGLL Adjustable Height Base, Single, Powered, Ganging - TFL Top $ 2299 12 $27,588 71NGBSA23 Adjustable Single Ganging Bracket/Cover Kit, Black $ 225 11 $ 2,475 71N40VWM23 Vertical Wire Manager $ 132 12 $ 1,584 71N72ELE Power Entry Whip Hardwire $ 100 1 $ 100 71N22ELJ 22" Ganging Jumper $ 58 11 $ 638 Total $32,385 Electrical included with powered units are a Phase 3 system; 3-circuit/5-wire system. 1, 2, 3, or hardwire circuit configurations can be selected for the receptacles. Standard-capacity power block, provides power, and has 2 receptacles per user. Hardwire selection will include 2 installed empty back to back or single junction boxes Vertical wire managers must be ordered separately and are used to conceal conduit and cables between the worksurface and center beam Ganging jumpers must be ordered separately and are used to jump power from 1 unit to the next Center beam mounted or edge mounted privacy screens can be ordered separately Power entry pole can be used to conceal power to the system. This is sold separately and is used to conceal the data and power cables from the floor to the unit. This is non-supporting and can enter at either end or in between benches at the connection point Grommet mounted monitor arms can be ordered separately Horizontal wire manager included with the base model provides a trough for cable to the power/data through tray cut-outs Powered single sided adjustable height units ship with the base, top, beam, horizontal wire manager, electrical, and feet Each worksurface is sized 1½" smaller in width than the model number dimensions to eliminate creep factor and pinch points when ganged together Ganging bracket/cover kit must be ordered separately Feet must be used 36 NATIONAL OFFICE FURNITURE CASEGOODS 2
THOUGHT STARTERS FIXED HEIGHT - NON-POWERED DOUBLE SIDED CENTER BEAM The overall number of units ganged is only limited based on electrical and floor space. Units are sold as a Start, Mid, or End model. A continuous run of units always require a start and end. Additional Mid models can be added in the middle to create a longer run. Widths available in 48", 54", 60", 66", and 72" Start Mid End Worksurface depths in 22 ¼" or 28 ¼" Depths available in 48" or 60" for double depth bases. Worksurfaces available in HPL or TFL. 6 USER STATION **Image shown above PART NUMBER PART DESCRIPTION PRICE QUANTITY EXT 71N6072FB2NSLL Fixed Height Base, Double, Non-Powered, Start - TFL Top $ 1861 1 $ 1,861 71N6072FB2NMLL Fixed Height Base, Double, Non-Powered, Mid - TFL Top $ 1704 1 $ 1,704 71N6072FB2NELL Fixed Height Base, Double, Non-Powered, End - TFL Top $ 1704 1 $ 1,704 Total $ 5,269 10 USER STATION PART NUMBER PART DESCRIPTION PRICE QUANTITY EXT 71N6072FB2NSLL Fixed Height Base, Double, Non-Powered, Start - TFL Top $ 1861 1 $ 1,861 71N6072FB2NMLL Fixed Height Base, Double, Non-Powered, Mid - TFL Top $ 1704 3 $ 5,112 71N6072FB2NELL Fixed Height Base, Double, Non-Powered, End - TFL Top $ 1704 1 $ 1,704 Total $ 8,677 Non-powered double fixed height units ship with the base, top, and center beam support Center beam mounted privacy screens can be ordered separately Center beam mounted or grommet mounted monitor arms can be ordered separately Grommet cutouts can be selected in the worksurface to add above worksurface power (see page 26 for grommet selections). The G17A, G17B, or G17C powered grommet must be ordered separately to be installed in the grommet cutout NATIONAL OFFICE FURNITURE CASEGOODS 2 37
THOUGHT STARTERS FIXED HEIGHT - NON-POWERED DOUBLE SIDED CENTER BEAM The overall number of units ganged is only limited based on electrical and floor space. Worksurface depths in 22 ¼" or 28 ¼" Widths available in 48", 54", 60", 66", and 72" Start Mid Mid Mid Mid End Depths available in 48" or 60" for double depth bases. Worksurfaces available in HPL or TFL. 12 USER STATION PART NUMBER PART DESCRIPTION PRICE QUANTITY EXT 71N6072FB2NSLL Fixed Height Base, Double, Non-Powered, Start - TFL Top $ 1861 1 $ 1,861 71N6072FB2NMLL Fixed Height Base, Double, Non-Powered, Mid - TFL Top $ 1704 4 $ 6,816 71N6072FB2NELL Fixed Height Base, Double, Non-Powered, End - TFL Top $ 1704 1 $ 1,704 Total $10,381 Non-powered double fixed height units ship with the base, top, and center beam support Center beam mounted privacy screens can be ordered separately Center beam mounted or grommet mounted monitor arms can be ordered separately Grommet cutouts can be selected in the worksurface to add above worksurface power (see page 26 for grommet selections). The G17A, G17B, or G17C powered grommet must be ordered separately to be installed in the grommet cutout 38 NATIONAL OFFICE FURNITURE CASEGOODS 2
THOUGHT STARTERS FIXED HEIGHT - NON-POWERED SINGLE SIDED BEAM, GANGING The overall number of units ganged is only limited based on electrical and floor space. Units are used as freestanding or can be ganged together to create a run of units. These can gang to single ganging or start, end and double freestanding units. Ganging kits must be ordered separately. Worksurface depths in 22 ¼" or 28 ¼" Widths available in 48", 54", 60", 66", and 72" Worksurfaces available in HPL or TFL. 3 USER STATION **Image shown above PART NUMBER PART DESCRIPTION PRICE QUANTITY EXT 71N2460FB1NGLL Fixed Height Base, Single Sided, Non-Powered - TFL Top $ 1077 3 $ 3,231 71NGBSF23 Fixed Height Single Ganging Bracket/Cover Kit, Black $ 75 2 $ 150 Total $ 3,381 6 USER STATION PART NUMBER PART DESCRIPTION PRICE QUANTITY EXT 71N2460FB1NGLL Fixed Height Base, Single Sided, Non-Powered - TFL Top $ 1077 6 $ 6,462 71NGBSF23 Fixed Height Single Ganging Bracket/Cover Kit, Black $ 75 5 $ 375 Total $ 6,837 Non-powered single sided fixed height units ship with the base, top, and beam Ganging bracket/cover kit must be ordered separately Beam mounted privacy screens can be ordered separately Beam mounted or grommet mounted monitor arms can be ordered separately Grommet cutouts can be selected in the worksurface to add above worksurface power (see page 26 for grommet selections). The G17A, G17B, or G17C powered grommet must be ordered separately to be installed in the grommet cutout NATIONAL OFFICE FURNITURE CASEGOODS 2 39
THOUGHT STARTERS FIXED HEIGHT - NON-POWERED SINGLE SIDED BEAM, GANGING The overall number of units ganged is only limited based on electrical and floor space. Worksurface depths in 22 ¼" or 28 ¼" Widths available in 48", 54", 60", 66", and 72" Worksurfaces available in HPL or TFL. 12 USER STATION PART NUMBER PART DESCRIPTION PRICE QUANTITY EXT 71N2448FB1NGLL Fixed Height Base, Single Sided, Non-Powered - TFL Top $ 996 12 $11,952 71NGBSF23 Fixed Height Single Ganging Bracket/Cover Kit, Black $ 75 11 $ 825 71N4813PVDP Privacy Screen, Rectangular - Resin, Grade 1 $ 507 12 $ 6,084 Total $18,861 Non-powered single sided fixed height units ship with the base, top, and beam Ganging bracket/cover kit must be ordered separately Beam mounted privacy screens can be ordered separately Beam mounted or grommet mounted monitor arms can be ordered separately Grommet cutouts can be selected in the worksurface to add above worksurface power (see page 26 for grommet selections). The G17A, G17B, or G17C powered grommet must be ordered separately to be installed in the grommet cutout 40 NATIONAL OFFICE FURNITURE CASEGOODS 2
THOUGHT STARTERS FIXED HEIGHT - POWERED DOUBLE SIDED PHASE 3 CENTER BEAM The overall number of units ganged is only limited based on electrical and floor space. Units are sold as a Start, Mid, or End model. A continuous run of units always require a start and end. Additional Mid models can be added in the middle to create a longer run. Widths available in 48", 54", 60", 66", and 72" Start End Depths available in 48" or 60" for double depth bases. Worksurfaces available in HPL or TFL. 4 USER STATION **Image shown above PART NUMBER PART DESCRIPTION PRICE QUANTITY EXT 71N6072FB2PSLL Fixed Height Base, Double, Powered, Start - TFL Top $ 2561 1 $ 2,561 71N6072FB2PELL Fixed Height Base, Double, Powered, End - TFL Top $ 2403 1 $ 2,403 71N72ELE Power Entry Whip Hardwire $ 100 1 $ 100 71N22ELJ 22" Ganging Jumper $ 58 1 $ 58 71N6918PVBPFA Beam Mounted Privacy Screen - Railroad, Grade A $ 735 2 $ 1,470 Total $ 6,592 8 USER STATION PART NUMBER PART DESCRIPTION PRICE QUANTITY EXT 71N6072FB2PSLL Fixed Height Base, Double, Powered, Start - TFL Top $ 2561 1 $ 2,561 71N6072FB2PMLL Fixed Height Base, Double, Powered, Mid - TFL Top $ 2403 2 $ 4,806 71N6072FB2PELL Fixed Height Base, Double, Powered, End - TFL Top $ 2403 1 $ 2,403 71N72ELE Power Entry Whip Hardwire $ 100 1 $ 100 71N22ELJ 22" Ganging Jumper $ 58 3 $ 174 71N6918PVBPFA Beam Mounted Privacy Screen - Railroad, Grade A $ 735 4 $ 2,940 Total $12,984 Electrical included with powered units are a Phase 3 system; 3-circuit/5-wire system. 1, 2, 3, or hardwire circuit configurations can be selected for the receptacles. Standard-capacity power block, provides back-to-back power, and has 2 receptacles per side. Hardwire selection will include 2 installed empty back to back junction boxes Ganging jumpers must be ordered separately and are used to jump power from 1 unit to the next Center beam mounted privacy screens can be ordered separately Power entry pole can be used to conceal power to the system. This is sold separately and is used to conceal the data and power cables from the floor to the unit. This is non-supporting and can enter at either end or in between benches at the connection point Center beam mounted monitor arms can be ordered separately Horizontal wire manager included with the base model provides a trough for cable to the power/data through tray cut-outs Powered double sided fixed height units ship with the base, top, center beam support, horizontal wire manager, and electrical Wire management cutout comes standard in the worksurface of a powered fixed height unit; this allows easy access to the below surface electrical NATIONAL OFFICE FURNITURE CASEGOODS 2 41
THOUGHT STARTERS FIXED HEIGHT - POWERED DOUBLE SIDED PHASE 3 CENTER BEAM The overall number of units ganged is only limited based on electrical and floor space. Widths available in 48", 54", 60", 66", and 72" Start Mid Mid Mid Mid End Depths available in 48" or 60" for double depth bases. Worksurfaces available in HPL or TFL. 12 USER STATION PART NUMBER PART DESCRIPTION PRICE QUANTITY EXT 71N6072FB2PSLL Fixed Height Base, Double, Powered, Start - TFL Top $ 2561 1 $ 2,561 71N6072FB2PMLL Fixed Height Base, Double, Powered, Mid - TFL Top $ 2403 4 $ 9,612 71N6072FB2PELL Fixed Height Base, Double, Powered, End - TFL Top $ 2403 1 $ 2,403 71N72ELE Power Entry Whip Hardwire $ 100 1 $ 100 71N22ELJ 22" Ganging Jumper $ 58 5 $ 290 71N6918PVBPFA Beam Mounted Privacy Screen - Railroad, Grade A $ 735 6 $ 4,410 Total $19,376 Electrical included with powered units are a Phase 3 system; 3-circuit/5-wire system. 1, 2, 3, or hardwire circuit configurations can be selected for the receptacles. Standard-capacity power block, provides back-to-back power, and has 2 receptacles per side. Hardwire selection will include 2 installed empty back to back junction boxes Ganging jumpers must be ordered separately and are used to jump power from 1 unit to the next Center beam mounted privacy screens can be ordered separately Power entry pole can be used to conceal power to the system. This is sold separately and is used to conceal the data and power cables from the floor to the unit. This is non-supporting and can enter at either end or in between benches at the connection point Center beam mounted monitor arms can be ordered separately Horizontal wire manager included with the base model provides a trough for cable to the power/data through tray cut-outs Powered double sided fixed height units ship with the base, top, center beam support, horizontal wire manager, and electrical Wire management cutout comes standard in the worksurface of a powered fixed height unit; this allows easy access to the below surface electrical 42 NATIONAL OFFICE FURNITURE CASEGOODS 2
THOUGHT STARTERS FIXED HEIGHT - POWERED SINGLE SIDED PHASE 3 CENTER BEAM, GANGING The overall number of units ganged is only limited based on electrical and floor space. Units are used as freestanding or can be ganged together to create a run of units. These can gang to single ganging or start, end and double freestanding units. Ganging kits must be ordered separately. Worksurface depths in 22 ¼" or 28 ¼" Widths available in 48", 54", 60", 66", and 72" Worksurfaces available in HPL or TFL. 4 USER STATION PART NUMBER PART DESCRIPTION PRICE QUANTITY EXT 71N2460FB1PGLL Fixed Height Base, Single Sided, Powered - TFL Top $ 1477 4 $ 5,908 71NGBSF23 Fixed Height Single Ganging Bracket/Cover Kit, Black $ 75 3 $ 225 71N72ELE Power Entry Whip Hardwire $ 100 1 $ 100 71N22ELJ 22" Ganging Jumper $ 58 3 $ 174 71N6013PVDP Beam Mounted Privacy Screen - Rectangular - Resin, Grade 1 $ 567 4 $ 2,268 Total $ 8,675 5 USER STATION **Image shown above PART NUMBER PART DESCRIPTION PRICE QUANTITY EXT 71N2460FB1PGLL Fixed Height Base, Single Sided, Powered - TFL Top $ 1477 5 $ 7,385 71NGBSF23 Fixed Height Single Ganging Bracket/Cover Kit, Black $ 75 4 $ 300 71N72ELE Power Entry Whip Hardwire $ 100 1 $ 100 71N22ELJ 22" Ganging Jumper $ 58 4 $ 232 71N6013PVDP Beam Mounted Privacy Screen - Rectangular - Resin, Grade 1 $ 567 5 $ 2,835 Total $10,852 Electrical included with powered units are a Phase 3 system; 3-circuit/5-wire system. 1, 2, 3, or hardwire circuit configurations can be selected for the receptacles. Standard-capacity power block, provides single power, and has 2 receptacles per user. Hardwire selection will include 2 installed empty back to back or single junction boxes Ganging jumpers must be ordered separately and are used to jump power from 1 unit to the next Beam mounted privacy screens can be ordered separately Power entry pole can be used to conceal power to the system. This is sold separately and is used to conceal the data and power cables from the floor to the unit. This is non-supporting and can enter at either end or in between benches at the connection point Beam mounted monitor arms can be ordered separately Horizontal wire manager included with the base model provides a trough for cable to the power/data through tray cut-outs Powered single sided fixed height units ship with the base, top, beam, horizontal wire manager, and electrical Wire management cutout comes standard in the worksurface of a powered fixed height unit; this allows easy access to the below surface electrical Ganging bracket/cover kit must be ordered separately NATIONAL OFFICE FURNITURE CASEGOODS 2 43
THOUGHT STARTERS FIXED HEIGHT - POWERED SINGLE SIDED PHASE 3 CENTER BEAM, GANGING The overall number of units ganged is only limited based on electrical and floor space. Worksurface depths in 22 ¼" or 28 ¼" Widths available in 48", 54", 60", 66", and 72" Worksurfaces available in HPL or TFL. 12 USER STATION PART NUMBER PART DESCRIPTION PRICE QUANTITY EXT 71N2448FB1PGLL Fixed Height Base, Single Sided, Powered - TFL Top $ 1396 12 $16,752 71NGBSF23 Fixed Height Single Ganging Bracket/Cover Kit, Black $ 75 11 $ 825 71N72ELE Power Entry Whip Hardwire $ 100 1 $ 100 71N22ELJ 22" Ganging Jumper $ 58 11 $ 638 Total $18,315 Electrical included with powered units are a Phase 3 system; 3-circuit/5-wire system. 1, 2, 3, or hardwire circuit configurations can be selected for the receptacles. Standard-capacity power block, provides single power, and has 2 receptacles per user. Hardwire selection will include 2 installed empty back to back or single junction boxes Ganging jumpers must be ordered separately and are used to jump power from 1 unit to the next Beam mounted privacy screens can be ordered separately Power entry pole can be used to conceal power to the system. This is sold separately and is used to conceal the data and power cables from the floor to the unit. This is non-supporting and can enter at either end or in between benches at the connection point Beam mounted monitor arms can be ordered separately Horizontal wire manager included with the base model provides a trough for cable to the power/data through tray cut-outs Powered single sided fixed height units ship with the base, top, beam, horizontal wire manager, and electrical Wire management cutout comes standard in the worksurface of a powered fixed height unit; this allows easy access to the below surface electrical Ganging bracket/cover kit must be ordered separately 44 NATIONAL OFFICE FURNITURE CASEGOODS 2