Automotive Data Solutions Inc. INSTALL GUIDE ADS-AL(DL)-NI NI Available for : ADS-AL CA Rev. Date: May 7, 0 Doc. No.: ##5455## 0055 Version FRançaise disponible en ligne au www.idatalink.com please visit www.idatalink.com/support for complete product details The brand names and logos found in this guide are property of their respective owners. Automotive Data Solutions Inc. 0 NOTICE: The manufacturer will accept no responsibility for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. This guide has been written for properly trained technicians; a certain level of skill & knowledge is therefore assumed. Please!review the Installation Guide carefully before beginning any work.
ADS-AL(DL)-NI PAGE 3-3 install guide install TYPE SELECTion FeATUReS Page of ADS-AL(DL)-NI Doc. No.: ##5455## 0055 MAKe MoDel YeAR nissan infiniti install TYPe DATA immobilizer BYPASS SeCURe TAKeoVeR PRioRiTY UnloCK DooR lock DooR UnloCK ARM oem AlARM DiSARM oem AlARM TRUnK/HATCH ReleASe DooR STAT output HooD STAT output* TRUnK STAT output TACHoMeTeR output FX35 03-04 FX35 05-08 FX35 Intelli-key 03-04 FX35 Intelli-key 05-08 FX45 03-04 FX45 05-08 FX45 Intelli-key 03-04 FX45 Intelli-key 05-08 G35 03-04 3 G35 05-06 G35 Intelli-Key 05-07 M35 05-07 M45 05-07 Q45 05-06 QX56 05-08 350Z 03-04 3 350Z 05-08 Altima 05-06 Armada 05-07 Frontier 05-08 Maxima 04 Maxima 05-08 Maxima Intelli-key 05-08 Murano 03-04 3 Murano 05-07 Murano Intelli-Key 05-07 Pathfinder 05-08 Quest 04 Quest 05-08 Titan 04 Titan 05-08 Xterra 05-08 * Hood status is only available when a factory hood switch is present.
Page 3 of ADS-AL(DL)-NI Doc. No.: ##5455## 0055 CoMPonEnT LoCATor M K J C H E F G D N
Page 4 of ADS-AL(DL)-NI Doc. No.: ##5455## 0055 TYPE - wire CroSS reference CHArT - of MAKe MoDel YeAR CAn H CAn l SeCURiTY light ConneCToR name TYPe location CoMPonenT locator nissan infiniti 350Z 05-08 6 Blue 4 Pink 3 Green/Orange M90 40 pin In Driver Kick Panel C Altima 05-06 6 Blue 4 Pink 3 Green/Orange M8 40 pin Left Of Steering Column J Armada 05-07 6 Blue 4 Pink 3 Green/Orange M8 40 pin Right Of Steering Column H Frontier 05-08 6 Blue 4 Pink 3 Green M8 40 pin Right Of Steering Column Over Brake Pedal E Maxima 04 6 Blue 4 Yellow 3 Green/Orange M8 40 pin Left Of Steering Column J Maxima 05-08 6 Blue 4 Pink 3 Green/Orange M8 40 pin Left Of Steering Column J Murano 05-08 6 Blue 4 Yellow 3 Green/Orange M34 40 pin Right Of Steering Column H Pathfinder 05-08 6 Blue 4 Pink 3 Green M65 40 pin Right Of Steering Column H Quest 04 6 Blue 4 Yellow 3 Green/Orange M8 40 pin At Bottom of A-Pilar Behind Air Duct M Quest 05-08 6 Blue 4 Pink 3 Green/Orange M8 40 pin At Bottom of A-Pilar Behind Air Duct M Titan 04 6 White 4 Red 3 Green/Orange M8 40 pin Right Of Steering Column H Titan 05-09 6 Blue 4 Pink 3 Green/Orange M8 40 pin Right Of Steering Column H Xterra 05-08 6 Blue 4 Pink 3 Green M8 40 pin Right Of Steering Column Over Brake Pedal E FX35 / FX45 03-08 6 Blue 4 Red 3 Green/Orange M3 40 pin In Driver Kick Panel C G35 Coupe 05 6 Blue 4 Red 3 Green/Orange M 40 pin In Driver Kick Panel C G35 05-06 6 Blue 4 Pink 3 Green/Orange M 40 pin In Driver Kick Panel C M35 / M45 05-07 6 Blue 4 Pink 3 White/Violet M 40 pin Behind Glove Box G Q45 05-06 6 Blue 4 Pink 65 Green M4 40 pin In Driver Kick Panel C QX56 05-08 6 Blue 4 Pink 3 Green/Orange M8 40 pin Right Of Steering Column H
Page 5 of ADS-AL(DL)-NI Doc. No.: ##5455## 0055 TYPE - wiring DIAGRAM - of BCM SEE CHART FOR LOCATION EXCEPTION: INFINITI Q45 05-06 SEE CHART FOR DETAILS 3 4 5 6 7 8 9 0 3 4 5 6 7 8 9 0 3 4 5 6 7 8 9 30 3 3 33 34 35 36 37 38 39 40 SECURITY LIGHT REMOTE STARTER TACH (AC) INPUT <- REQUIRED TRUNK (-) OUTPUT <- REQUIRED UNLOCK (-) OUTPUT <- REQUIRED LOCK (-) OUTPUT <- REQUIRED V(+) <- REQUIRED GROUND (-) <- REQUIRED GROUND WHEN RUNNING (-) INPUT <- REQUIRED REQUIRED -> IGNITION (+) OUTPUT OPTIONAL -> HOOD STATUS (-) INPUT OPTIONAL -> TRUNK STATUS (-) INPUT OPTIONAL -> DOOR STATUS (-) INPUT CONNECT EITHER OR STANDARD WIRING (RS3) PORT REQUIRED ON REMOTE STARTER. IF UNAVAILABLE USE STANDARD WIRING METHOD GWR (-) OUTPUT - BLUE/WHITE GROUND - BLACK V - RED LOCK/ARM (-) INPUT - GREEN/BLACK UNLOCK/DISARM (-) INPUT - BLUE/BLACK TRUNK (-) INPUT - RED/WHITE (NC) BROWN (NC) PURPLE/YELLOW (NC) PURPLE/BLACK (NC) BLACK/WHITE (NC) GREEN *TACH (AC) OUTPUT - PURPLE/WHITE WHITE/BLACK - LIGHT CONNECTOR SIDE WHITE/RED - LIGHT VEHICULE SIDE WHITE (NC) YELLOW/BLACK - DOOR STATUS (-) OUTPUT* YELLOW/RED - TRUNK STATUS (-) OUTPUT* YELLOW - HOOD STATUS (-) OUTPUT* BROWN/RED - CANH BROWN/YELLOW - CANL ORANGE/BLACK (NC) ORANGE/WHITE (NC) ORANGE (NC) PINK/BLACK (NC) PINK - IGNITION (+) INPUT LEGEND Wiring connections not required when installed in idatalink mode * Wiring connection not required in -way idatalink BLUE/RED (NC) BLUE/YELLOW (NC) GREEN/RED (NC) GREEN/YELLOW (NC) GRAY/RED (NC) GRAY/YELLOW (NC) OBDII CONNECTOR LOCATED UNDER DRIVER SIDE DASH SEE CHART FOR WIRE COLORS 9 0 CANL CANH 3 4 5 6 3 4 7 5 8 6
Page 6 of ADS-AL(DL)-NI Doc. No.: ##5455## 0055 TYPE - wire CroSS reference CHArT - of CAnH CAnl intelli-key (+) ConneCToR SeCURiTY light (-) ConneCToR MAKe MoDel YeAR nissan infiniti name TYPe location* name TYPe location* Maxima Intelli-key 05-07 6 Blue 4 Pink 6 Green M5 40 pin F 3 Green/Orange M8 40 pin K Maxima Intelli-key 08 6 Blue 4 Pink 6 Green M5 40 pin F 3 Green/Orange M8 40 pin K Murano 06 6 Blue 4 Yellow 6 Green M99 40 pin N 3 Green/Orange M35 40 pin H Murano 07 6 Blue 4 Yellow 6 Green M99 40 pin N 3 Green/Orange M35 40 pin H FX35 Intelli-key 03-04 6 Blue 4 Pink 6 Green/Red M34 40 pin F 3 Green/Orange M3 40 pin D FX35 Intelli-key 05 6 Blue 4 Yellow 6 Green/Red M34 40 pin M 3 Green/Orange M3 40 pin C FX35 Intelli-key 06 6 Blue 4 Yellow 6 White M34 40 pin M 3 Green/Orange M3 40 pin C FX35 Intelli-key 07 6 Blue 4 Yellow 6 White M34 40 pin M 3 Green/Orange M3 40 pin C FX35 Intelli-key 08 6 Blue 4 Pink 6 White M34 40 pin M 3 Green/Orange M3 40 pin C FX45 Intelli-key 03-04 6 Blue 4 Pink 6 Green/Red M34 40 pin F 3 Green/Orange M3 40 pin D FX45 Intelli-key 05 6 Blue 4 Red 6 Green/Red M34 40 pin M 3 Green/Orange M3 40 pin C FX45 Intelli-key 06 6 Blue 4 Yellow 6 White M34 40 pin M 3 Green/Orange M3 40 pin C FX45 Intelli-key 07 6 Blue 4 Yellow 6 White M34 40 pin M 3 Green/Orange M3 40 pin C FX45 Intelli-key 08 6 Blue 4 Pink 6 White M34 40 pin M 3 Green/Orange M3 40 pin C G35 Intelli-key Sedan 05 6 Blue 4 Pink 6 Yellow/Green M75 40 pin G 3 Green/Orange M 40 pin C G35 Intelli-key 06 6 Blue 4 Pink 6 Yellow/Green M75 40 pin G 3 Green/Orange M 40 pin C G35 Intelli-key Coupe 07 6 Blue 4 Pink 6 Yellow/Green M75 40 pin G 3 Green/Orange M 40 pin C G K H C F M L D N *legend - CoMPonenT locator Behind glove box Above drivers kick panel Right of steering column At drivers kick panel Right of steering column above gas pedal Behind cluster, left of dash, near "A" Pillar Behind mirror controls, left of steering column At BCM in passenger kick panel Behind glove box, near "A" Pillar
Page 7 of ADS-AL(DL)-NI Doc. No.: ##5455## 0055 TYPE - wiring DIAGRAM - of INTELLIGENT KEY UNIT REFER TO CHART FOR INTELLIGENT KEY UNIT LOCATION REFER TO CHART FOR PIN LOCATION AND WIRE COLOR BCM SEE CHART FOR LOCATION 3 4 5 6 7 8 9 0 3 4 5 6 7 8 9 0 3 4 5 6 7 8 9 30 3 3 33 34 35 36 37 38 39 40 SECURITY LED ARE NOT PRESENT IN ALL VEHICULES. IF DURING YOUR REMOTE START SEQUENCE THE SECURITY LED STAYS ON OR FLASHES, YOU MUST CUT OFF THE SECURITY LED WIRE. CONNECTOR SIDE VEHICLE SIDE 3 4 5 6 7 8 9 0 3 4 5 6 7 8 9 0 3 4 5 6 7 8 9 30 3 3 33 34 35 36 37 38 39 40 REMOTE STARTER SECURITY LED REFER TO CHART FOR PIN LOCATION AND WIRE COLOR CONNECTOR SIDE TACH (AC) INPUT <- REQUIRED TRUNK (-) OUTPUT <- REQUIRED UNLOCK (-) OUTPUT <- REQUIRED LOCK (-) OUTPUT <- REQUIRED V(+) <- REQUIRED GROUND (-) <- REQUIRED GROUND WHEN RUNNING (-) INPUT <- REQUIRED CONNECT EITHER OR STANDARD WIRING REQUIRED -> IGNITION (+) OUTPUT OPTIONAL -> HOOD STATUS (-) INPUT OPTIONAL -> TRUNK STATUS (-) INPUT OPTIONAL -> DOOR STATUS (-) INPUT VEHICLE SIDE (RS3) PORT REQUIRED ON REMOTE STARTER. IF UNAVAILABLE USE STANDARD WIRING METHOD GWR (-) OUTPUT - BLUE/WHITE GROUND - BLACK V - RED LOCK/ARM (-) INPUT - GREEN/BLACK UNLOCK/DISARM (-) INPUT - BLUE/BLACK TRUNK (-) INPUT - RED/WHITE (NC) BROWN (NC) PURPLE/YELLOW (NC) PURPLE/BLACK (NC) BLACK/WHITE (NC) GREEN *TACH (AC) OUTPUT - PURPLE/WHITE WHITE/BLACK - SMART KEY INTERRUPT OUT WHITE/RED - SMART KEY INTERRUPT IN WHITE (NC) YELLOW/BLACK - DOOR STATUS (-) OUTPUT* YELLOW/RED - TRUNK STATUS (-) OUTPUT* YELLOW - HOOD STATUS (-) OUTPUT* BROWN/RED - CANH BROWN/YELLOW - CANL ORANGE/BLACK (NC) ORANGE/WHITE (NC) ORANGE (NC) PINK/BLACK (NC) PINK - IGNITION (+) INPUT LEGEND Wiring connections not required when installed in idatalink mode * Wiring connection not required in -way idatalink BLUE/RED - SECURITY LED IN BLUE/YELLOW - SECURITY LED OUT GREEN/RED (NC) GREEN/YELLOW (NC) GRAY/RED (NC) GRAY/YELLOW (NC) OBDII CONNECTOR LOCATED UNDER DRIVER SIDE DASH SEE CHART FOR WIRE COLORS 9 0 3 4 5 3 6 4 CANH 7 5 8 6 CANL
Page 8 of ADS-AL(DL)-NI Doc. No.: ##5455## 0055 TYPE 3 - wire CroSS reference CHArT - of MAKe MoDel YeAR CAn H CAn l SeCURiTY light ConneCToR name TYPe location CoMPonenT locator nissan infiniti 350Z 03-04 70 Blue 7 Red 55 Green/Orange M3 4 pin In Driver Kick Panel C Murano 03-04 70 Blue 7 Yellow 55 Green/Orange M37 4 pin Right Of Steering Column H G35 Sedan 03-04 70 Blue 7 Red 55 Green/Orange M3 4 pin In Driver Kick Panel C G35 Coupe 03-04 70 Blue 7 Red 55 Green/Orange M3 4 pin In Driver Kick Panel C
Page 9 of ADS-AL(DL)-NI Doc. No.: ##5455## 0055 TYPE 3 - wiring DIAGRAM - of BCM SEE CHART FOR LOCATION REMOTE STARTER 63 6 6 60 59 58 57 56 55 54 53 76 75 74 73 7 7 70 69 68 67 66 65 64 CANL CANH SECURITY LIGHT TACH (AC) INPUT <- REQUIRED TRUNK (-) OUTPUT <- REQUIRED UNLOCK (-) OUTPUT <- REQUIRED LOCK (-) OUTPUT <- REQUIRED V(+) <- REQUIRED GROUND (-) <- REQUIRED GROUND WHEN RUNNING (-) INPUT <- REQUIRED REQUIRED -> IGNITION (+) OUTPUT OPTIONAL -> HOOD STATUS (-) INPUT OPTIONAL -> TRUNK STATUS (-) INPUT OPTIONAL -> DOOR STATUS (-) INPUT CONNECT EITHER OR STANDARD WIRING (RS3) PORT REQUIRED ON REMOTE STARTER. IF UNAVAILABLE USE STANDARD WIRING METHOD GWR (-) OUTPUT - BLUE/WHITE GROUND - BLACK V - RED LOCK/ARM (-) INPUT - GREEN/BLACK UNLOCK/DISARM (-) INPUT - BLUE/BLACK TRUNK (-) INPUT - RED/WHITE (NC) BROWN (NC) PURPLE/YELLOW (NC) PURPLE/BLACK (NC) BLACK/WHITE (NC) GREEN *TACH (AC) OUTPUT - PURPLE/WHITE LEGEND Wiring connections not required when installed in idatalink mode * Wiring connection not required in -way idatalink WHITE/BLACK - SECURITY LIGHT (-) CONNECTOR SIDE WHITE/RED - SECURITY LIGHT (-) VEHICULE SIDE WHITE (NC) YELLOW/BLACK - DOOR STATUS (-) OUTPUT* YELLOW/RED - TRUNK STATUS (-) OUTPUT* YELLOW - HOOD STATUS (-) OUTPUT* BROWN/RED - CANH BROWN/YELLOW - CANL ORANGE/BLACK (NC) ORANGE/WHITE (NC) ORANGE (NC) PINK/BLACK (NC) PINK - IGNITION (+) INPUT BLUE/RED (NC) BLUE/YELLOW (NC) GREEN/RED (NC) GREEN/YELLOW (NC) GRAY/RED (NC) GRAY/YELLOW (NC)
Page 0 of ADS-AL(DL)-NI Doc. No.: ##5455## 0055 installation MoDE SELECTion Press and release programming button to select installation mode. LED flashes (X) once = DATA MODE LED flashes (X) twice = STANDARD HARDWIRE MODE! Press and hold programming button until LED turns solid GREEN to register selection. After registration, follow Factory Reset Procedure to change installation mode and restart this procedure. MoDULE ProgrAMMing ProCEDUrE Insert key into ignition. 3 Wait, LED will turn solid GREEN for seconds. ON Turn key to ON position. 4 5 OFF Turn key to OFF position. Module Programming Procedure completed.
Page of ADS-AL(DL)-NI Doc. No.: ##5455## 0055 identify VEHiCLE YEAr Locate the Vehicle Identification Number (VIN) and identify the 0th character. 4 3 A 5 Y N 5 T A L 8 D 5 R 0 X Match the VIN s 0th character to its corresponding year. l > 990 S > 995 Y > 000 5 > 005 A > 00 M > 99 T > 996 > 00 6 > 006 B > 0 n > 99 V > 997 > 00 7 > 007 C > 0 P > 993 W > 998 3 > 003 8 > 008 D > 03 R > 994 X > 999 4 > 004 9 > 009 e > 04 led STATUS Flashing RED DiAGnoSTiCS DURinG PRoGRAMMinG DURinG ReMoTe START WiTH ignition off Missing/wrong information from firmware or vehicle Incorrectly programmed Solid RED Waiting for more vehicle information Incorrectly programmed Flashing GREEN Additional steps required to complete programming MoDULE DiAgnoSTiCS Correctly programmed and operational Incorrectly programmed or connected Not programmed waiting for more vehicle information False ground when running status from remote starter Solid GREEN then OFF Correctly programmed Reset in progress Reset in progress OFF No activity or already programmed Invalid ground when running status from remote starter At rest and ready for a remote start sequence factory reset ProCEDUrE DISCONNECT all connectors from module EXCEPT the black 4-PIN standard or optional data connector. DISCONNECT black 4-PIN standard or optional data connector. 5 6 LED will turn solid red for seconds. RESET COMPLETED. RECONNECT all connectors. 3 4 PRESS AND HOLD programming button while connecting either 4-PIN standard or optional data connector. When LED flashes red, RELEASE programming button. 7! Repeat programming procedure. Failure to follow procedure may result with a DTC or a CHECK ENGINE error message. This product is protected by one or more of the following patents: U.S. LETTErS PATEnT no. 5,79,55; 6,0,460; 6,43,004; 6,49,6; 6,75,47; 6,97,73; 6,346,876; 6,39,534; 6,59,4; 6,696,97; 6,756,885; 6,756,886; 6,77,67; 6,8,89; 6,94,750; 7,00,40; 7,03,86; 7,046,6; 7,06,37; 7,068,53; 7,05,830; 7,05,679; 7,4,083; 7,369,936; 7,378,945; 7,489,33; 7,50,937; CAnADiAn PATEnT no.,30,48;,45,03;,46,670;,44,99;,45,0;,45,07;,45,038;,45,04;,50,893;,45,490;,45,96;,45,487; EUroPEAn PATEnT no.,053,8; DE 69807-94T; U.S. 00045535; 006098; 0060984; 00400784; 008003036; 009007955; EP500565; 538038; 538037;