Food Waterjet cutting machine technical specifications

Food Waterjet cutting machine technical specifications

FOOD machines are innovation and revolutionized the food processing frozen or not Frozen cut of foods quickly, clean and without contact with any type of blade. They used either in food or in large gourmet confection with which many products reach given its versatility to cut any type of food and in any state. Food Waterjet cutting machine technical specifications Model OneJet Food 08*06 cutting Area 0.8m x 0.6m Maximum travel X axis Maximum travel Y axis Maximum travel Z axis cutting table type Motion Speed X / Y / Z axis (mm/min) Maximum cutting speed (mm/min) Maximum load on the table Dymanic cutting head Precise movements Lubrication system Tolerance in movement axis 850mm 650mm 200 mm Manual cantilever X & Y 10000 mm/min; Z Manual 0 a 10000 mm/min 100 kgs by square meter NO Recirculating ball screws and linear guides Auto lurbicate system X & Y Axis ±0.03 mm Re-Position precision ± 0.025 mm (±0.001") Limit switches Mechanic and soft end limit swith in all axis

1. The Machine came complete, Cutting Table CNC, CNC control, High pressure pump and all piping and wire conection. 2. Linear guide and ball srew shaft are brand "SKF (ABBA)" o "HIWIN" 3. Servo moto on Axis "X"&"Y" Brand MITSUBISHI, FUJI", "PANASONIC" o YASKAWA and for "Z" axis is servo motor made in Japan 4. All Axis longer than 6000 MM long, will be Tempered toothed rack and pinion so the accuracy will be lower Technical specifications of the Ultra High Pressure pump 420 MPA Nominal power of the main engine Nominal current of the main motor Main Engine Brand Main engine Low start Pressure control system Maximum Circuit Breaker at 380V/50Hz H.P Control System / Language PLC Inlet Water Pressure range request Inlet water pressure after Booster High Pressure Attenuator volume Inlet water Filter assembly Request for water treatment Maximum high-pressure limit Hydraulic High Pressure piping Outlet High Pressure tubing High Pressure tubing Inside Pump 37 kw(50 hp) 380 V/50 Hz 80 A SIEMENS Engine 37 kw (50 hp) SIEMENS Low Start Dual system pressure auto - control (Low/high range 70~380 MPa) 160 A Schneider Main swich SIEMENS PLC Control / English languaje 0.2~6.0 bar 6~10 bar 1.30 Liter maintenance free attenuator 5 μm, 1 μm, 0.1 μm 3 filtros According to the requirement of inlet water quality 420 MPa (4000 bar) 3 layers steel wired hydraulic piping from Germany 1/4 High Pressure tubing from USA 3/8 High Pressure tubing from USA

Display information Safety high Pressure protections (In display) Safety Hydraulic pressure overflow valve (In display) Safety Over stroke protected main Engine (In display) Safety Over oil temperature protected (In display) Safety Too low inlet water pressure protected (In display) Pressurization / intensifier rate Intensifier Type High Pressure stable Hydraulic Tank Capacity Capacidad del acumulador Potencia Nominal de motor principal Maximum Pressure Maximum noise level Maximum water flow rate Temperatura ambiente de operación oil Pump brand & model Válvula bi direccional Inlet water pressure, outlet high pressure, oil pressure, oil temperature Hidraulic 1:20 (oil : water) 50 hp Short type 25~380 MPa (3500~55,000 psi) 120 Liter 1,3 Liter 50 HP (37 kw) 420 MPA / 60000 PSI / 4000 bar 75 db (A) 3,7 liter /min mín 5 C (40 F) máx 40 C (104 F) LyYuan-Rexroth Mod: A10V a pistones axiales SUNNY(U.S.A) Oil Type and Brand Hidráulic Anti-Wear Shell Tellus S2 M 46

Controlled oil temp range 25~50 C Maximum Hydraulic Pressure Hidraulic Oil tank capacity Maximum Flow Rate at 1440rpm Maximum Input Power Maximum Torque Maximum Oil Pressure pump 210 bar 120 Li 156 lítros / min 37 kw 160 Nm 21.5 MPa (3000 psi) Technical specifications of the CNC control Easy and friendly Control 3D cutting Simulator The operator select the material, thickness, Press START and the machine do the rest. 3D cutting available interpolating 3 axes simultaneously standard in all machines Abrasive flow regulator on line On line on Screen viable 0 to 100% Keyboard wirless CNC Extension file accepted Dinamic speed NESTING SOFTWARE Dual high and low pressure system on line standard in all machines NC Studio PC Based Win XP English Language dwg. dxf. nce. nc. cnc. eng. plt. G-code etc. Dynamically controlled to speed corners and small radius One Licence incuding with the machine BOB CAD CAM V21 English you can chose to cut or engrave

Limit switches High Pressure control engrave possibility of cutting with water only Z automatic safety By software and by swich to avoid collisions Pressure control 0.001mm(μm control) with the same programe the operator can chose low pressure and make engrave Just chose only water cutting Using this to avoid collisions Optional Garnet Auto Feeder 120/200 L water cooler 10-15 C - Chiller Laser Point Sales@onejet.com.cn - www.onejet.com.cn