Index - Section 14 End Suction Pump Semi-Open Impeller

Index - Section End Suction Pump Semi-Open Impeller ITEM S Product Numbering System...1 Typical Architects / Engineers Specifi cations - Series 4000...2 Seal Application...3-4 Technical Charts...5-6 Pump Assembly, Fig. 4000 & 4011...7-8 Dimensions, Fig. 4001, Sizes: 1", 1½" & 2½"...9-10 Dimensions, Fig. 4001, Sizes: 1", 1½" (Special Flanged)...11-12 Dimensions, Fig. 4011, Sizes: 1¼S, 1½S, 1½M, 2S & 2M...13 - Dimensions, Fig. 4011, Sizes: 3S, 3M, 4S & 4M, (Special Flanged) 1¼S, 1½S, 1½M, 2S & 2M...15-16 Dimensions, Fig. 4011, w/type C Drip Lip Base, Sizes: 1¼S, 1½S, 1½M, 2S & 2M...17 Dimensions, Fig. 4011, Type C Drip Lip Base, Sizes: 3S, 3M, 4S & 4M, (Special Flanged) 1¼S, 1½S, 1½M, 2S & 2M...18 Dimensions, Fig. 4021 (4021H), Sizes: 1¼S, 1½S, 1½M, 1½L, 2S & 2M...19-20 Dimensions, Fig. 4021 (or 4021H), Sizes: 3S, 3M, 4M, 4MS, 5M, 5MS, 6M & 6ML, (Special Flanged) 1¼S, 1½S, 1½M, 1½L, 2S & 2M...21-22 Dimensions, Fig. 4021 (4021H), Type C Drip Lip Base, Sizes: 1¼S, 1½S, 1½M, 1½L, 2S & 2M...23 Dimensions, Fig. 4021 (4021H), Type C Drip Lip Base, Sizes: 3S, 3M, 4M, 4MS, 5M, 5MS, 6M & 6ML (Special Flanged) 1¼S, 1½S, 1½M, 1½L, 2S & 2M...24 Selection Curves Fig. 4001, 4011 & 4021, 1750, 3500 & 1150RPM...25-26 Performance Curve, Fig 4001, 1750RPM...27-28 Performance Curve, Fig 4011 & 4021 1750RPM...29-35 Performance Curve, Fig 4001, 4011, 4021 & 4021H, 3500RPM...36-39 Performance Curve, Fig 4011, 4021, 1150RPM...40-46

This page intentionally left blank

Series 4000 - Product Numbering System Semi-Open Impeller The Product Numbering System used, consists of 12 digits, and the following is a description of that system: 0000-000 - 0 0-000 1 thru 4 5 thru 7 8 9 10 thru 12 Digits 1 thru 4 describe the pump figure number. 1 thru 4 Description 4001 4011 4021 4021H Smallest Sizes, Frame Mounted, Open Impeller Intermediate Sizes, Frame Mounted, Open Impeller Large Sizes, Frame Mounted, Open Impeller Large Sizes with Heavy Duty Frames. Frame Mounted, Open Impeller Digits 5 thru 7 describe the pump size. 5 thru 7 Description 5 thru 7 Description 5 thru 7 Description 000 100 133 150 156 157 158 Power Frame Only 1 1-1/4S 1-1/2 1-1/2L 1-1/2M 1-1/2S Digits 8 describe the power frame. 1 2 3 4 1" Taper Standard (4001, 4011, 4021) 1" Taper Heavy Duty (4021H) 1-1/4" Taper Standard (4021) 1-1/4" Taper Heavy Duty (4021H) Digits 9 describe the rotation 0 1 Right Hand Left Hand 207 208 250 307 327 308 407 2M 2S 2-1/2 3M 3MD 3S 4M Digit 10 thru 12 describes the pump material and sealing method 10 thru 12 Description 10 thru 12 Description 400 300 031 331 051 551 700 417 750 021 725 002 032 332 052 552 SFAI with Standard Packing SFAI with Standard Packing & 316SS Shaft SFAI with S-21 BF1C1 Seal SFAI with S-21 BF171 Seal SFAI with D-21 BF1C1 Seal SFAI with D-21 BF171 Seal SFAI with Standard Packing & Split Gland SFAI with Standard Packing & 17-4PH Shaft SFAI with S-21 BF1C1 seal & 17-4PH Shaft SFAI with Standard Packing & Locked Bearings No Longer Available Bronze Fitted with Standard Packing Bronze Fitted with S-21 BF1C1 Seal Bronze Fitted with S-21 BF171 Seal Bronze Fitted with D-21 BF1C1 Seal Bronze Fitted with D-21 BF171 Seal 022 003 033 053 004 013 0 016 038 391 591 592 593 405 408 507 511 607 609 4S 5M 5MS 6M/6MD 6ML Bronze Fitted with Standard Packing & Locked Bearings #8 All Bronze with Standard Packing #8 All Bronze with S-21 BF1C1 Seal #8 All Bronze with D-21 BF1C1 Seal 316 Stainless Steel with Tefl on Packing (Power Frame) with Tefl on Packing, 316SS Shaft 1" Taper for 316SS LE (Power Frame) with Tefl on Packing, 316SS Shaft 1-1/4" Taper for 316SS LE HD (Power Frame) with Tefl on Packing, 316SS Shaft 1" Taper for 316SS LE With BF1C1 Special for Waukesha Special for Duncan Special for Duncan Special for Duncan Special for Duncan Special for Duncan 1 6/17

Typical Architects/Engineers Specifications Series: 4000 General The contractor shall furnish and install as show on the plans qty Deming horizontal frame mounted Series 4000 size centrifugal pump(s) as herein specifi ed. The pump(s) shall be rated for continuous service and of (all iron)(bronze fi tted)(all bronze) construction for the following operating conditions. Each pump shall be capable of delivering a primary condition of GPM of liquid against feet total head. A secondary point of GPM at feet of head and a shut off of feet within a minimum effi ciency of % at the primary conditions. Liquid Handled Temperature Specifi c gravity Viscosity of liquid at pumping temperature NPSH A NOTE: Add any additional facts concerning the nature of the liquid or installation which might affect pump construction, application or operation. Model 4001, 4011, 4021 Horizontal Frame Mounted The design requires a 416 stainless steel shaft sized for a maximum defl ection of.002 at the seal faces with the pump running at RPM maximum load conditions. The bearings shall be (grease)(oil) lubricated having a 2-year minimum life (AFBMA B 10 ) under the maximum load conditions and protected form outside contamination. The shaft and bearings are to be encased in a cast iron ASTM-A48 Class 30 frame and to be of a micrometer adjustment design. The pump and motor will be mounted on a common (fabricated steel with drip rim)(fabricated steel) baseplate. Pumps are to be coupled to the driver by means of an approved non-spacer type coupling with an OSHA approved coupling guard. Construction Details Casing shall be of (cast iron)(bronze) and suitable for the medium being pumped. The casing shall be vertically split with tangential discharge and capable of standing hydrostatic test pressures of 1-1/2 times maximum working pressure. All assembly points shall be of machine register fi t to assure proper pump alignment. The casing shall also have a tapped and plugged drain connection available for any of the eight (8) rotatable casing discharge positions. Casing Connection The threaded and fl anged casing nozzles shall conform to ANSI B16.1 and NPT specifi cations with a minimum 125 PSI ratings, all fl anged nozzle connections shall be standard fl at face. Flange units start with 3 discharge connections; below 3 are NPT threaded. Impeller The impeller shall be of the taper bore semi-enclosed single suction type of (cast iron)(bronze) both statically and hydraulically balanced for maximum effi ciency and smooth operation. Holes shall be provided through the impeller hub to keep positive pressure on the packing or mechanical seal and balance axial thrust loads. Impeller shall be positioned and securely locked to the shaft by the use of a Woodruff key, hex head castilated nut, pin, and washer. Motor The motor shall be not less than hp RPM. NEMA design B squirrel cage type, (drip proof)(tefc) EISA effi ciency motor with (1.15)(1.0) service factor and suitable for operation on (115)(230) volt, 1 phase, (50) (60) Hertz power supply OR (200)(230)(460)(575) volt, 3 phase, 60 Hertz power supply. Motor size shall be suffi cient to prevent overloading at operating conditions or at the lowest listed head conditions whichever point requires greater horsepower. Following installation, grouting and connection of all piping, pump and motor must be checked for alignment in accordance with standards of the Hydraulic Institute. 2 12/10

Seal Application Use of Heat Exchanger on Centrifugal Pumps Equipped With Single Mechanical Seal and Choker Ring The single mechanical seal available on Deming 4000, 4100 and 4200 Series pumps is recommended for handling clear liquids at temperatures not exceeding 180 F. A small portion of the liquid being pumped is recirculated from the discharge thru the seal chamber to act as a lubricated and coolant. For Hot Water Service at higher temperatures Choker Ring Construction is recommended. The choker ring is installed in the annular space at the end of the seal chamber as shown in Figure 2 to restrict the fl ow back to the impeller. This increases the pressure in the seal chamber which in turn increases the boiling point of the water and the safe operating temperature. Satisfactory seal life is obtained at the moderate pressures generally encountered on hot water circulating applications with water temperatures up to 225 F. Water treatment, chromate content, operating pressure and temperature are interrelated factors effecting seal life. For more severe service conditions at higher pressures longer seal life can be obtained if the liquid in the seal chamber is cooled to approximately 170 F. This may be accomplished without dilution of the liquid being pumped by passing the recirculating liquid through a heat exchanger as shown in Figure 1. Where the temperature may exceed 225 F. Even when the pump is not running, special seal materials may be required. Refer conditions to factory for recommendation. FIGURE 2 FIGURE 1 3

Seal Application A valve must be used on the cooling line for control. This will enable one to cool the seal water suffi ciently at a minimum fl ow rating of cooling water. Heat exchanges can be selected as follows: 1. Determine the recirculation capacity from the graph shown in Figure 3. 2. Use Chart 1 below to select the proper heat exchanger. 3. Determine the cost for the heat exchanger also from Chart 1. Heat Exchanger Recir. Hot Water Cooling Water Whitlock Temp. F GPM Temp. F Model Size In Out In Out (App.) 1-3 BW-21 3" x 21" 280 170 3-5 (2 Pass) 5-7 75 130 1-3 BW-18 3" x 18" 260 170 3-5 75 120 5-7 1-3 BW-15 3" x 15" 240 170 3-5 75 110 5-7 CHART 1 GPM (App.) 4 8 12 4 8 12 4 8 12 SCHEDULE C List $150.00 $2.00 $134.00 4

Technical Chart Figure 4001 4011 4021 4021 HD Size 1 1½ 2½ 1¼ S 1½ S 2S 3S 4S 1½ M 2M 3M 4M 1½ M 2M 3M 4M 5M 5 MS 6M 1½ L 1¼ S 1½ S 2S 3S 1½ M 2M 3M 4M 5M 5 MS 6M 6 ML 1½ L Suction 1½ 2 3 1½ 2 2½ 4 5 2 3 4 5 2 3 4 5 6 6 6 2 1½ 2 2½ 4 2 3 4 5 6 6 6 6 2 Discharge 1 1½ 2½ 1¼ 1½ 2 3 4 1½ 2 3 4 1½ 2 3 4 5 5 6 1½ 1¼ 1½ 2 3 1½ 2 3 4 5 5 6 6 1½ Max. Impeller Dia. 6 6 7 8 8 8 8 8 10 10 10 10 10 10 10 10 10 10 10 12 8 8 8 8 10 10 10 10 10 10 10 10 12 Max. Dia. Solids ⅜ 11 /16 1 5/16 7 /16 11 /16 1⅛ 15 /16 7 /16 ⅝ 1-3 /16 1½ 7 /16 ⅝ 1-3 /16 1½ 1¼ 1½ 1⅜ 7 /16 5 /16 7 /16 11 /16 1⅛ 7 /16 ⅝ 1-3 /16 1-1½ 1¼ 1½ 1⅜ 9 7/16 /16 Shaft Dia. at Coupling Dia. at Bearing (St. Box End) Dia. at Bearing (Coupling End) ⅞ 1 1¼ 1¼.984 1.181 1.378 1.575.984 1.181 1.378 1.378 Dia. at St. Box ⅞ 1 1¼ 1½ Dia. at Impeller ⅞ 1 1 1¼ 1 1¼ Max. H.P. at 1750 RPM Max. H.P. at 3500 RPM 5 10 25 35 10 10 20 30 Stuffi ng Box I.D. 1⅜ 1⅝ 1⅞ 2⅛ Stuffi ng Box Length Lantern Ring Width 1¾ 2 5 /16 2 5 /16 2¾ ⅜ ½ ½ ¾ Packing Size ¼ SQ. 5/16 SQ. 5/16 SQ. 5/16 SQ. No. Length 5-3¾ 5-4⅜ 5-5¼ 6 Bearing at Stuffi ng Box End Bearing at Coupling End Bearing C.L. to Bearing C.L. Bearing C.L. to Impeller C.L. Suction Wall Thickness Volute (Casing) Wall Thickness Bolts on Glands (2) Max. Discharge Pressure (P.S.I.) C.L. to C.L. of Bolts on Gland Weight Bare Pump (Lbs.) Casing Capacity (Gal.) Casing Connector Avail. T=Threaded F=Flanged Hyrdostatic Test Pressure ND3205 ND7606WLI ND5607WLI ND5608WLI ND7505 OR ND5505LI ND7606 OR ND5606WLI ND7607 OR ND5607WLI ND5607WLI 4⅜ 6 6¼ 6½ 6⅜ 6½ 6⅞ 7½ 7-9/16 7-8- 11/16 1/16 8¼ 7-9/16 7-11/16 8-9- 1/16 8⅜ 8½ 8⅝ 9 5/16 9-9- 5/16 5/16 9½ 8-9/16 8-8- 8-8- 8-8- 8-9- 9-9- 9-11/32 13/32 17/32 29/32 15/32 19/32 31/32 9/32 9/32 9/32 15/32 9⅜ 8-9/16 ¼ ¼ ¼ 5 /16 5 /16 5 /16 5 /16 ⅜ 5 /16 5 /16 5 /16 ⅜ 5 /16 5 /16 5 /16 ⅜ ⅜ ⅜ ⅜ 5 /16 7 /16 5 /16 5 /16 5 /16 5 /16 5 /16 5 /16 ⅜ ⅜ ⅜ ⅜ ⅜ 5 /16 ¼ ¼ 5 /16 5/16 ⅜ 5/16 ⅜ 5/16 5/16 ⅜ 5/16 x 1½ 5/16 x 2 5/16 x 2 ⅜ x 2¼ 150 150 150 150 2⅜ 2⅞ 3⅛ 3⅜ 55 59 78 83 85 90 120 138 102 107 130 162 122 127 150 184 200 204 233 139 105 107 112 2 124 129 152 186 201 205 234 233 1 T F T F T T F T F T F F F T F T F T F F T F T F T F F F F F 225 P.S.I. T F T F T F T F F T F T F T F F F F F F T F Impeller Eye Area 2.76 3. 7.07 3.98 4.91 4.91 12.6 12.6 4.67 7.07 12.6 12.6 4.67 7.07 12.6 12.6 21.7 12.6 28.3 4.91 3.98 4.91 4.91 12.6 4.67 7.07 12.6 12.6 21.7 12.6 28.3 28.3 4.91 5 6/08

Pump Assembly - Fig. 4001 Item No. Name of Part Item No. Name of Part Item No. Name of Part 1 2 6 9 11 *13 *16 17 *18 19 24 *29 32 37 40 46 Casing Impeller Pump Shaft Suction Cover Packing Box Cover Packing Ball Bearing (Inboard) Split Gland Ball Bearing (Outboard) Frame Impeller Nut Lantern Ring Impeller Key Bearing Cover (Outboard) Defl ector Coupling Key *49 66 *73 127 203 204 207 208 209 210 213 2 215 216 229 Bearing Cover Seal (Outboard) Shaft Adjusting Unit Casing Gasket Tubing Assembly with Connectors Name Plate Adjusting Lock Nut Grease Fitting Pipe Plug Cap Screw, Machine Bolt, or Stud Hex Nut Cap Screw Drive Screw Cap Screws Pipe Plug Lockwasher 236 239 240 *241 242 243 257 *269 270 *303 337 347 352 Pipe Plug Cap Screws Pipe Plug Stuffi ng Box Gasket Grease Fitting Grease Fitting Clamping Ring Cotter Pin Impeller Washer Bearing Cover Gasket Cap Screw Spring Pipe Plug * Recommended spare parts 7 7/08

Pump Assembly - Fig. 4011-4021 Item No. Name of Part Item No. Name of Part Item No. Name of Part 1 2 6 9 11 *13 *16 17 *18 19 24 *29 32 37 40 Casing Impeller Pump Shaft Suction Cover Packing Box Cover Packing Ball Bearing (Inboard) Split Gland Ball Bearing (Outboard) Frame Impeller Nut Lantern Ring Impeller Key Bearing Cover (Outboard) Defl ector 46 *49 66 *73 127 203 204 207 208 209 210 213 2 215 216 Coupling Key Bearing Cover Seal (Felt Ring) Shaft Adjusting Unit Casing Gasket Tubing Assembly with Connectors Name Plate Adjusting Lock Nut Grease Fitting Pipe Plug Cap Screw, Machine Bolt, or Stud Hex Nut Cap Screw Drive Screw Cap Screws Pipe Plug 229 236 239 240 *241 242 243 257 *269 270 *303 337 347 352 Lockwasher Pipe Plug Cap Screws Pipe Plug Stuffi ng Box Gasket Grease Fitting Grease Fitting Clamping Ring Cotter Pin Impeller Washer Bearing Cover Gasket Cap Screw Spring Pipe Plug * Recommended spare parts 8 7/08

Fig. 4001 - Sizes 1", 1½" & 2½" Pump with Steel Base, Coupling & Motor USE THIS DIMENSION WHEN USING BASE 17716-8 DIMENSIONS IN INCHES SIZE SUCT. DISCH. X Y Z CP HL * HL 1 1½ 1 4¼ 1 15 /16 3½ 16 4½ 4⅞ 1½ 2 1½ 5½ 2 7 /16 3¾ 16⅝ 5⅛ 5½ 2½ 3 2½ 6¼ 3 1 /16 4¾ 17¾ 6¼ 6⅝ BASE DIMENSIONS IN INCHES FRAME NO 48 56 3T 5T 182T 184T 213T 215T 254T 256T BASE NO. 17716-1 17716-2 11716-2 11716-2 16812 16812 17716-5 17716-5 17716-8 17716-8 HA 8 10 10 10 12 12 12 12 15 15 HB 22 24 24 24 26 26 30 30 36 36 C 11 13 11 /16 13⅛ 13⅛ ⅝ 15⅝ 17¾ 19¼ 22⅞ 24⅝ HD 7¾ 8⅛ 8⅛ 8⅛ 8½ 8½ 8½ 8½ 9¾ 9¾ HE 3 4 4 4 4¾ 4¾ 4¾ 4¾ 5¾ 5¾ HF 20¾ 22¾ 22¾ 22¾ 24¾ 24¾ 28¾ 28¾ 34 34 HG 2¼ 2⅝ 2⅝ 2⅝ 3 3 3 3 3½ 3½ HH ⅝ ⅝ ⅝ ⅝ ⅝ ⅝ ⅝ ⅝ ⅝ ⅝ HP ⅝ ⅝ ⅝ ⅝ ⅝ ⅝ ⅝ ⅝ 1 1 HT ½ ½ ½ ½ ¾ ¾ ¾ ¾ 1 1 DISCHARGE POSITIONS SHOWN EACH 45 Customer Shop Order No. Date: By: Pump Motor Fig. No. Size Curve No. GPM Head Sp. Gr. Temp. Rotation Packing/Seal MFGR Hp RPM Phase-Cycle Voltage Frame Enclosure Insulation Furnished by Mounted 9

Fig. 4001 - Sizes 1", 1½" & 2½" Basic Pump DIMENSIONS IN INCHES SIZE SUCT. DISCH. A B CP D DD E F G H L O P U V X Y Z KEYWAY 1 1½ 1 5 7½ 16 5½ 4 2 5½ ⅜ ½ 4⅞ 9¾ 1 ⅞ 2 4¼ 1 15 /16 3½ 1½ 2 1½ 5 7½ 16⅝ 5½ 4¼ 2 5½ ⅜ ½ 5½ 11 1 ⅞ 2 5½ 2 7 /16 3¾ 3/16 x 3 /32 x 2 2½ 3 2½ 5 7½ 17¾ 5½ 5½ 2 5½ ⅜ ½ 6⅝ 11¾ 1 ⅞ 2 6¼ 3 1 /16 4¾ Customer Shop Order No. Date: By: Pump Motor Fig. No. Size Curve No. GPM Head Sp. Gr. Temp. Rotation Packing/Seal MFGR Hp RPM Phase-Cycle Voltage Frame Enclosure Insulation Furnished by Mounted 10

Fig. 4001 - Sizes 1"& 1½" (Special Flanged) Pump with Steel Base, Coupling & Motor * USE THIS DIMENSION WHEN USING BASE 17716-8 PUMP SIZE SUCTION 125LB SIZE DIA. FLG. BOLTS BOLT CIRCLE DIMENSIONS IN INCHES DISCHARGE 125LB SIZE DIA. FLG. BOLTS BOLT CIRCLE X Y Z CP HL * HL 1 1½ 5 4 - ½ 3⅞ 1 4¼ 4 - ½ 3⅛ 5 3¼ 3½ 17⅜ 5⅞ 6¼ 1½ 2 6 4 - ⅝ 4¾ 1½ 5 4 - ½ 3⅞ 5½ 3⅜ 3¾ 17⅝ 6⅛ 6½ BASE DIMENSIONS IN INCHES FRAME NO 48 56 3T 5T 182T 184T 213T 215T 254T BASE NO. 17716-1 17716-2 11716-2 11716-2 16812 16812 17716-5 17716-5 17716-8 HA 8 10 10 10 12 12 12 12 15 HB 22 24 24 24 26 26 30 30 36 C 11 13 11 /16 13⅛ 13⅛ ⅝ 15⅝ 17¾ 19¼ 22⅞ HD 7¾ 8⅛ 8⅛ 8⅛ 8½ 8½ 8½ 8½ 9¾ HE 3 4 4 4 4¾ 4¾ 4¾ 4¾ 5¾ HF 20¾ 22¾ 22¾ 22¾ 24¾ 24¾ 28¾ 28¾ 34 HG 2¼ 2⅝ 2⅝ 2⅝ 3 3 3 3 3½ HH ⅝ ⅝ ⅝ ⅝ ⅝ ⅝ ⅝ ⅝ ⅝ HP ⅝ ⅝ ⅝ ⅝ ⅝ ⅝ ⅝ ⅝ 1 HT ½ ½ ½ ½ ¾ ¾ ¾ ¾ 1 DISCHARGE POSITIONS SHOWN EACH 45 Customer Shop Order No. Date: By: Pump Motor Fig. No. Size Curve No. GPM Head Sp. Gr. Temp. Rotation Packing/Seal MFGR Hp RPM Phase-Cycle Voltage Frame Enclosure Insulation Furnished by Mounted 11

Fig. 4001 - Sizes 1"& 1½" (Special Flanged) Basic Pump DIMENSIONS IN INCHES - FLANGES ARE 125LB A.S.A. STD SIZE SUCT. DISCH. A B CP D DD E F G H L O P U V X Y Z KEYWAY 1 1½ 1 5 7½ 17⅜ 5½ 4 2 5½ ⅜ ½ 6¼ 10½ 1 ⅞ 2 5 3¼ 3½ 3 /16 x 3 /32 x 2 1½ 2 1½ 5 7½ 17⅝ 5½ 4¼ 2 5½ ⅜ ½ 6½ 11 1 ⅞ 2 5½ 3⅜ 3¾ Customer Shop Order No. Date: By: Pump Motor Fig. No. Size Curve No. GPM Head Sp. Gr. Temp. Rotation Packing/Seal MFGR Hp RPM Phase-Cycle Voltage Frame Enclosure Insulation Furnished by Mounted 12

Fig. 4011 - Sizes 1¼S, 1½S, 1½M, 2S & 2M Pumps with Type A or B Steel Base, Coupling & Motor DIMENSIONS IN INCHES SIZE SUCT. DISCH. X Y Z CP HL 1¼S 1½ 1¼ 5½ 2 1 /16 4¾ 19¾ 5½ 1½S 2 1½ 5¾ 2⅛ 4¾ 19⅞ 5⅝ 1½M 2 1½ 6½ 2¼ 5¾ 20 5¾ 2S 2½ 2 6¼ 2¼ 4¾ 20⅛ 5⅞ 2M 3 2 7 2½ 5¾ 20⅜ 6⅛ DISCHARGE POSITIONS SHOWN EACH 45 BASE DIMENSIONS IN INCHES FRAME NO 56 3T 5T 182T 184T 213T 215T 254T 256T 284TS 284T 286TS 286T BASE NO. 27501 27501 27501 27502 27502 27503 27503 27504 27504 27504 27504 27504 27505 HA 12 12 12 12 12 12 12 15 15 15 15 15 15 HB 28 28 28 32 32 36 36 40 40 40 40 40 43 C 13 11 /16 13⅛ 13⅛ ⅝ 15⅝ 17¾ 19¼ 22⅞ 24⅝ 24½ 25⅞ 26 27⅜ HD 9 9 9 9 9 9 9 9⅝ 9⅝ 10⅜ 10⅜ 10⅜ 10⅜ HE 4¾ 4¾ 4¾ 4¾ 4¾ 4¾ 4¾ 6 6 6 6 6 6 HF 25½ 25½ 25½ 29½ 29½ 33½ 33½ 37½ 37½ 37½ 37½ 37½ 40½ HG 3 3 3 3 3 3 3 3⅜ 3⅜ 3⅜ 3⅜ 3⅜ 3⅜ HT ½ ½ ½ ¾ ¾ ¾ ¾ 1 1 1 1 1 1 Customer Shop Order No. Date: By: Pump Motor Fig. No. Size Curve No. GPM Head Sp. Gr. Temp. Rotation Packing/Seal MFGR Hp RPM Phase-Cycle Voltage Frame Enclosure Insulation Furnished by Mounted 13

Fig. 4011 - Sizes 1¼S, 1½S, 1½M, 2S & 2M Basic Pump DIMENSIONS IN INCHES SIZE SUCT. DISCH. A B CP D DD E F G H L O P U V X Y Z KEYWAY 1¼S 1½ 1¼ 7 10½ 19¾ 6 5⅜ 3 8¼ ½ 7 /16 5⅜ 11½ 1⅛ 1 2¼ 5½ 2 1 /16 4¾ 1½S 2 1½ 7 10½ 19⅞ 6 5⅜ 3 8¼ ½ 7/16 5½ 11¾ 1⅛ 1 2¼ 5¾ 2⅛ 4¾ 1½M 2 1½ 7 10½ 20 6 6⅜ 3 8¼ ½ 7 /16 5⅝ 12½ 1⅛ 1 2¼ 6½ 2¼ 5¾ ¼ x ⅛ x 2 2S 2½ 2 7 10½ 20⅛ 6 5¾ 3 8¼ ½ 7/16 5¾ 12¼ 1⅛ 1 2¼ 6¼ 2¼ 4¾ 2M 3 2 7 10½ 20⅜ 6 6½ 3 8¼ ½ 7/16 6 13 1⅛ 1 2¼ 7 2½ 5¾ Customer Shop Order No. Date: By: Pump Motor Fig. No. Size Curve No. GPM Head Sp. Gr. Temp. Rotation Packing/Seal MFGR Hp RPM Phase-Cycle Voltage Frame Enclosure Insulation Furnished by Mounted

Fig. 4011 - Sizes 3S, 3M, 4S & 4M Sizes 1¼S, 1½S, 1½M, 2S & 2M (Special Flanged) Pump with Type A & B Steel Base, Coupling & Motor DIMENSIONS IN INCHES SUCTION 125LB DISCHARGE 125LB PUMP BOLT SIZE DIA. FLG. BOLTS BOLT SIZE SIZE DIA. FLG. BOLTS CIRCLE CIRCLE X Y Z CP HL S 1¼S 1½ 5 4 - ½ 3⅞ 1¼ 4⅝ 4 - ½ 3½ 6 3⅜ 4¾ 21⅛ 6⅞ --- 1½S 2 6 4 - ⅝ 4¾ 1½ 5 4 - ½ 3⅞ 5¾ 3¾ 4¾ 21½ 7¼ --- 1½M 2 6 4 - ⅝ 4¾ 1½ 5 4 - ½ 3⅞ 6½ 3¾ 5¾ 21½ 7¼ --- 2S 2½ 7 4 - ⅝ 5½ 2 6 4 - ⅝ 4¾ 6¼ 3⅞ 4¾ 21¾ 7½ --- 2M 3 7½ 4 - ⅝ 6 2 6 4 - ⅝ 4¾ 7 3⅞ 5¾ 21¾ 7½ --- 3S 4 9 8 - ⅝ 7½ 3 7½ 4 - ⅝ 6 7 5⅞ 5¼ 24 9¾ --- 3M 4 9 8 - ⅝ 7½ 3 7½ 4 - ⅝ 6 8 5⅞ 6¼ 24 9¾ --- 4S 5 10 8 - ¾ 8½ 4 9 8 - ⅝ 7½ 7 6⅛ 6 24½ 10¼ ½ 4M 5 10 8 - ¾ 8½ 4 9 8 - ⅝ 7½ 9 6⅛ 6½ 24⅝ 10⅜ ½ BASE DIMENSIONS IN INCHES FRAME NO 56 3T 5T 182T 184T 213T 215T 254T 256T 284TS 284T 286TS 286T BASE NO. 27501 27501 27501 27502 27502 27503 27503 27504 27504 27504 27504 27504 27505 HA 12 12 12 12 12 12 12 15 15 15 15 15 15 HB 28 28 28 32 32 36 36 40 40 40 40 40 43 C 13 11 /16 13⅛ 13⅛ ⅝ 15⅝ 17¾ 19¼ 22⅞ 24⅝ 24½ 25⅞ 26 27⅜ HD 9 9 9 9 9 9 9 9⅝ 9⅝ 10⅜ 10⅜ 10⅜ 10⅜ HE 4¾ 4¾ 4¾ 4¾ 4¾ 4¾ 4¾ 6 6 6 6 6 6 HF 25½ 25½ 25½ 29½ 29½ 33½ 33½ 37½ 37½ 37½ 37½ 37½ 40½ HG 3 3 3 3 3 3 3 3⅜ 3⅜ 3⅜ 3⅜ 3⅜ 3⅜ HT ½ ½ ½ ¾ ¾ ¾ ¾ 1 1 1 1 1 1 DISCHARGE POSITIONS SHOWN EACH 45 Customer Shop Order No. Date: By: Pump Motor Fig. No. Size Curve No. GPM Head Sp. Gr. Temp. Rotation Packing/Seal MFGR Hp RPM Phase-Cycle Voltage Frame Enclosure Insulation Furnished by Mounted 15

Fig. 4011 - Sizes 3S, 3M, 4S & 4M Sizes 1¼S, 1½S, 1½M, 2S & 2M (Special Flanged) Basic Pump DIMENSIONS IN INCHES - FLANGES ARE 125LB A.S.A STD. SIZE SUCT. DISCH. A B CP D DD E F G H L O P S U V X Y Z KEYWAY 3S 4 3 7 10½ 24 6 6 3 8¼ ½ 7/16 9⅝ 13 1⅛ --- 1 2¼ 7 5⅞ 5¼ 3M 4 3 7 10½ 24 6 7 3 8¼ ½ 7 /16 9⅝ 1⅛ --- 1 2¼ 8 5⅞ 6¼ ¼ x ⅛ x 2 4S 5 4 7 10½ 24½ 6 7¼ 3 8¼ ½ 7/16 10⅛ 13 1⅛ ½ 1 2¼ 7 6⅛ 6 4M 5 4 7 10½ 24⅝ 6 7½ 3 8¼ ½ 7 /16 10¼ 15 1⅛ ½ 1 2¼ 9 6⅛ 6½ 1¼S 1½ 1¼ 7 10½ 21⅛ 6 5⅜ 3 8¼ ½ 7/16 6¾ 12 1⅛ --- 1 2¼ 6 3⅜ 4¾ 1½S 2 1½ 7 10½ 21½ 6 5⅜ 3 8¼ ½ 7 /16 7⅛ 11¾ 1⅛ --- 1 2¼ 5¾ 3¾ 4¾ 1½M 2 1½ 7 10½ 21½ 6 6⅜ 3 8¼ ½ 7/16 7⅛ 12½ 1⅛ --- 1 2¼ 6½ 3¾ 5¾ 2S 2½ 2 7 10½ 21¾ 6 5¾ 3 8¼ ½ 7/16 7⅜ 12¼ 1⅛ --- 1 2¼ 6¼ 3⅞ 4¾ 2M 3 2 7 10½ 21¾ 6 6½ 3 8¼ ½ 7 /16 7⅜ 13 1⅛ --- 1 2¼ 7 3⅞ 5¾ ¼ x ⅛ x 2 NOTE: Flanged Connectors are special on size 2M and larger. Customer Shop Order No. Date: By: Pump Motor Fig. No. Size Curve No. GPM Head Sp. Gr. Temp. Rotation Packing/Seal MFGR Hp RPM Phase-Cycle Voltage Frame Enclosure Insulation Furnished by Mounted 16

Fig. 4011 - Sizes 1¼S, 1½S, 1½M, 2S & 2M Pump with Type C Drip Lip Steel Base, Coupling & Motor DIMENSIONS IN INCHES SIZE SUCT. DISCH. X Y Z CP HL 1¼S 1½ 1¼ 5½ 2 1 /16 4¾ 19¾ 5½ 1½S 2 1½ 5¾ 2⅛ 4¾ 19⅞ 5⅝ 1½M 2 1½ 6½ 2¼ 5¾ 20 5¾ 2S 2½ 2 6¼ 2¼ 4¾ 20⅛ 5⅞ 2M 3 2 7 2½ 5¾ 20⅜ 6⅛ DISCHARGE POSITIONS SHOWN EACH 45 BASE DIMENSIONS IN INCHES FRAME NO 56 3T 5T 182T 184T 213T 215T 254T 256T 284TS 284T 286TS 286T BASE NO. 27501 27501 27501 27502 27502 27503 27503 27504 27504 27504 27504 27504 27505 HA 12 12 12 12 12 12 12 15 15 15 15 15 15 HB 28 28 28 32 32 36 36 40 40 40 40 40 43 C 13 11 /16 13⅛ 13⅛ ⅝ 15⅝ 17¾ 19¼ 22⅞ 24⅝ 24½ 25⅞ 26 27⅜ HD 9 9 9 9 9 9 9 9⅝ 9⅝ 10⅜ 10⅜ 10⅜ 10⅜ HE 4¾ 4¾ 4¾ 4¾ 4¾ 4¾ 4¾ 6 6 6 6 6 6 HF 25½ 25½ 25½ 29½ 29½ 33½ 33½ 37½ 37½ 37½ 37½ 37½ 40½ HG 3 3 3 3 3 3 3 3⅜ 3⅜ 3⅜ 3⅜ 3⅜ 3⅜ HT ½ ½ ½ ¾ ¾ ¾ ¾ 1 1 1 1 1 1 Customer Shop Order No. Date: By: Pump Motor Fig. No. Size Curve No. GPM Head Sp. Gr. Temp. Rotation Packing/Seal MFGR Hp RPM Phase-Cycle Voltage Frame Enclosure Insulation Furnished by Mounted 17

Fig. 4011 - Sizes 3S, 3M, 4S & 4M Sizes 1¼S, 1½S, 1½M, 2S & 2M (Special Flanged) Pump with Type C Drip Lip Steel Base, Coupling & Motor DIMENSIONS IN INCHES SUCTION 125LB DISCHARGE 125LB PUMP BOLT SIZE DIA. FLG. BOLTS BOLT SIZE SIZE DIA. FLG. BOLTS CIRCLE CIRCLE X Y Z CP HL S 1¼S 1½ 5 4 - ½ 3⅞ 1¼ 4⅝ 4 - ½ 3½ 6 3⅜ 4¾ 21⅛ 6⅞ --- 1½S 2 6 4 - ⅝ 4¾ 1½ 5 4 - ½ 3⅞ 5¾ 3¾ 4¾ 21½ 7¼ --- 1½M 2 6 4 - ⅝ 4¾ 1½ 5 4 - ½ 3⅞ 6½ 3¾ 5¾ 21½ 7¼ --- 2S 2½ 7 4 - ⅝ 5½ 2 6 4 - ⅝ 4¾ 6¼ 3⅞ 4¾ 21¾ 7½ --- 2M 3 7½ 4 - ⅝ 6 2 6 4 - ⅝ 4¾ 7 3⅞ 5¾ 21¾ 7½ --- 3S 4 9 8 - ⅝ 7½ 3 7½ 4 - ⅝ 6 7 5⅞ 5¼ 24 9¾ --- 3M 4 9 8 - ⅝ 7½ 3 7½ 4 - ⅝ 6 8 5⅞ 6¼ 24 9¾ --- 4S 5 10 8 - ¾ 8½ 4 9 8 - ⅝ 7½ 7 6⅛ 6 24½ 10¼ ½ 4M 5 10 8 - ¾ 8½ 4 9 8 - ⅝ 7½ 9 6⅛ 6½ 24⅝ 10⅜ ½ BASE DIMENSIONS IN INCHES FRAME NO 56 3T 5T 182T 184T 213T 215T 254T 256T 284TS 284T 286TS 286T BASE NO. 27501 27501 27501 27502 27502 27503 27503 27504 27504 27504 27504 27504 27505 HA 12 12 12 12 12 12 12 15 15 15 15 15 15 HB 28 28 28 32 32 36 36 40 40 40 40 40 43 C 13 11 /16 13⅛ 13⅛ ⅝ 15⅝ 17¾ 19¼ 22⅞ 24⅝ 24½ 25⅞ 26 27⅜ HD 9 9 9 9 9 9 9 9⅝ 9⅝ 10⅜ 10⅜ 10⅜ 10⅜ HE 4¾ 4¾ 4¾ 4¾ 4¾ 4¾ 4¾ 6 6 6 6 6 6 HF 25½ 25½ 25½ 29½ 29½ 33½ 33½ 37½ 37½ 37½ 37½ 37½ 40½ HG 3 3 3 3 3 3 3 3⅜ 3⅜ 3⅜ 3⅜ 3⅜ 3⅜ HT ½ ½ ½ ¾ ¾ ¾ ¾ 1 1 1 1 1 1 Customer Shop Order No. Date: By: Pump Motor DISCHARGE POSITIONS SHOWN EACH 45 Fig. No. Size Curve No. GPM Head Sp. Gr. Temp. Rotation Packing/Seal MFGR Hp RPM Phase-Cycle Voltage Frame Enclosure Insulation Furnished by Mounted 18

Fig. 4021 (or 4021H) - Sizes 1¼S, 1½S, 1½M, 1½L 2S & 2M Pumps with Type A or B Steel Base, Coupling & Motor DIMENSIONS IN INCHES SIZE SUCT. DISCH. X Y Z CP HL 1¼S 1½ 1¼ 5½ 2 1 /16 4¾ 21¾ 5 7 /16 1½S 2 1½ 5¾ 2⅛ 4¾ 22 5 11 /16 1½M 2 1½ 6½ 2¼ 5¾ 22⅛ 5 13 /16 1½L 2 1½ 7½ 2¼ 6¾ 22⅛ 5 13 /16 2S 2½ 2 6¼ 2¼ 4¾ 22¼ 5 15 /16 2M 3 2 7 2½ 5¾ 22½ 6 3 /16 BASE DIMENSIONS IN INCHES FRAME NO 3T 5T 182T 184T 213T 215T 254T 256T 284TS 284T 286TS 286T BASE NO. 27501 27502 27502 27503 27503 27503 27504 27505 27504 27505 27505 27505 HA 12 12 12 12 12 12 15 15 15 15 15 15 HB 28 32 32 36 36 36 40 43 40 43 43 43 C 13⅛ 13⅛ ⅝ 15⅝ 17¾ 19¼ 22⅞ 24⅝ 24½ 25⅞ 26 27⅜ HD 10 10 10 10 10 10 10⅜ 10⅜ 10⅜ 10⅜ 10⅜ 10⅜ HE 4¾ 4¾ 4¾ 4¾ 4¾ 4¾ 6 6 6 6 6 6 HF 25½ 29½ 29½ 33½ 33½ 33½ 37½ 40½ 37½ 40½ 40½ 40½ HG 3 3 3 3 3 3 3⅜ 3⅜ 3⅜ 3⅜ 3⅜ 3⅜ HT ¾ ¾ ¾ ¾ ¾ ¾ 1 1 1 1 1 1 DISCHARGE POSITIONS SHOWN EACH 45 Customer Shop Order No. Date: By: Pump Motor Fig. No. Size Curve No. GPM Head Sp. Gr. Temp. Rotation Packing/Seal MFGR Hp RPM Phase-Cycle Voltage Frame Enclosure Insulation Furnished by Mounted 19

Fig. 4021 (or 4021H) - Sizes 1¼S, 1½S, 1½M, 1½L, 2S & 2M Basic Pump DIMENSIONS IN INCHES SIZE SUCT. DISCH. A B CP D DD E F G H L O P U V X Y Z KEYWAY 1¼S 1½ 1¼ 8 11 11 /16 21¾ 7 5⅜ 3⅜ 8½ ½ ⅝ 5⅞ 12½ 1 11 /16 1¼ 2¾ 5½ 2 1 /16 4¾ 1½S 2 1½ 8 11 11 /16 22 7 5⅜ 3⅜ 8½ ½ ⅝ 6⅛ 12¾ 1 11 /16 1¼ 2¾ 5¾ 2⅛ 4¾ 1½M 2 1½ 8 11 11 /16 22⅛ 7 6⅜ 3⅜ 8½ ½ ⅝ 6¼ 13½ 1 11 /16 1¼ 2¾ 6½ 2¼ 5¾ 1½L 2 1½ 8 11 11 /16 22⅛ 7 7⅜ 3⅜ 8½ ½ ⅝ 6¼ ½ 1 11 /16 1¼ 2¾ 7½ 2¼ 6¾ ¼ x ⅛ x 2¼ 2S 2½ 2 8 11 11 /16 22¼ 7 5¾ 3⅜ 8½ ½ ⅝ 6⅜ 13¼ 1 11 /16 1¼ 2¾ 6¼ 2¼ 4¾ 2M 3 2 8 11 11 /16 22½ 7 6½ 3⅜ 8½ ½ ⅝ 6⅝ 1 11 /16 1¼ 2¾ 7 2½ 5¾ Customer Shop Order No. Date: By: Pump Motor Fig. No. Size Curve No. GPM Head Sp. Gr. Temp. Rotation Packing/Seal MFGR Hp RPM Phase-Cycle Voltage Frame Enclosure Insulation Furnished by Mounted 20

Fig. 4021 (or 4021H) - Sizes 3S, 3M, 4M, 4MS, 5M, 5MS, 6M & 6ML Sizes 1¼S, 1½S, 1½M, 1½L, 2S & 2M (Special Flanged) Pump with Type A or B Steel Base, Coupling & Motor DIMENSIONS IN INCHES SUCTION 125LB DISCHARGE 125LB PUMP SIZE SIZE DIA. BOLTS BOLT SIZE DIA. BOLTS BOLT FLG. CIRCLE FLG. CIRCLE X Y Z CP HL S 1¼S 1½ 5 4 - ½ 3⅞ 1¼ 4⅝ 4 - ½ 3½ 6 3⅜ 4¾ 23⅛ 6 13 /16 --- 1½S 2 6 4 - ⅝ 4¾ 1½ 5 4 - ½ 3⅞ 5¾ 3¾ 4¾ 23½ 7 3 /16 --- 1½M 2 6 4 - ⅝ 4¾ 1½ 5 4 - ½ 3⅞ 6½ 3¾ 5¾ 23⅝ 7 5 /16 --- 1½L 2 6 4 - ⅝ 4¾ 1½ 5 4 - ½ 3⅞ 7½ 3¾ 6¾ 23⅝ 7 5 /16 2S 2½ 7 4 - ⅝ 5½ 2 6 4 - ⅝ 4¾ 6¼ 3⅞ 4¾ 23¾ 7 7 /16 --- 2M 3 7½ 4 - ⅝ 6 2 6 4 - ⅝ 4¾ 7 3⅞ 5¾ 23⅞ 7 9 /16 --- 3S 4 9 8 - ⅝ 7½ 3 7½ 4 - ⅝ 6 7 5⅞ 5¼ 26 9¾ --- 3M 4 9 8 - ⅝ 7½ 3 7½ 4 - ⅝ 6 8 5⅞ 6¼ 26 9¾ --- 4M, 4MS 5 10 8 - ¾ 8½ 4 9 8 - ⅝ 7½ 9 6⅛ 6½ 26⅝ 10 5 /16 ½ 5M, 5MS 6 11 8 - ¾ 9½ 5 10 8 - ¾ 8½ 9 6 7⅛ 26½ 10 3 /16 ½ 6M, 6ML 6 11 8 - ¾ 9½ 6 11 8 - ¾ 9½ 9 6¼ 8 26⅞ 10 9 /16 --- DISCHARGE POSITIONS SHOWN EACH 45 BASE DIMENSIONS IN INCHES FRAME NO 3T 5T 182T 184T 213T 215T 254T 256T 284TS 284T 286TS 286T 324TS 324T 326TS 326T 364TS 364T 365TS 365T BASE NO. 27501 27502 27502 27503 27503 27503 27504 27505 27504 27505 27505 27505 27507 27507 27507 27507 27507 27507 27507 27508 HA 12 12 12 12 12 12 15 15 15 15 15 15 18 18 18 18 18 18 18 18 HB 28 32 32 36 36 36 40 43 40 43 43 43 46 46 46 46 46 46 46 51 C 13⅛ 13⅛ ⅝ 15⅝ 17¾ 19¼ 22⅞ 24⅝ 24½ 25⅞ 26 27⅜ 27¼ 28¾ 28¾ 30¼ 31 33⅛ 32 34⅛ HD 10 10 10 10 10 10 10⅜ 10⅜ 10⅜ 10⅜ 10⅜ 10⅜ 12 12 12 12 13 13 13 13 HE 4¾ 4¾ 4¾ 4¾ 4¾ 4¾ 6 6 6 6 6 6 7½ 7½ 7½ 7½ 7½ 7½ 7½ 7½ HF 25½ 29½ 29½ 33½ 33½ 33½ 37½ 40½ 37½ 40½ 40½ 40½ 43½ 43½ 43½ 43½ 43½ 43½ 43½ 48½ HG 3 3 3 3 3 3 3⅜ 3⅜ 3⅜ 3⅜ 3⅜ 3⅜ 4 4 4 4 4 4 4 4 HT ¾ ¾ ¾ ¾ ¾ ¾ 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Customer Shop Order No. Date: By: Pump Motor Fig. No. Size Curve No. GPM Head Sp. Gr. Temp. Rotation Packing/Seal MFGR Hp RPM Phase-Cycle Voltage Frame Enclosure Insulation Furnished by Mounted 21

Fig. 4021 (or 4021H) - Sizes 3S, 3M, 4M, 4MS, 5M, 5MS, 6M & 6ML Sizes 1¼S, 1½S, 1½M, 1½L, 2S & 2M (Special Flanged) Basic Pump DIMENSIONS IN INCHES - FLANGES ARE 125LB A.S.A STD. SIZE SUCT. DISCH. A B CP D DD E F G H L O P S U V X Y Z KEYWAY 3S 4 3 8 11 11 /16 26 7 6 3⅜ 8½ ½ ⅝ 10 3 /16 1 11 /16 --- 1¼ 2¾ 7 5⅞ 5¼ 3M 4 3 8 11 11 /16 26 7 7 3⅜ 8½ ½ ⅝ 10 3 /16 15 1 11 /16 --- 1¼ 2¾ 8 5⅞ 6¼ 4M 4MS 5M 5MS 6M 6ML 5 4 8 11 11 /16 26⅝ 7 7½ 3⅜ 8½ ½ ⅝ 10¾ 16 1 11 /16 ½ 1¼ 2¾ 9 6⅛ 6½ 6 5 8 11 11 /16 26½ 7 8⅜ 3⅜ 8½ ½ ⅝ 10⅝ 16 1 11 /16 ½ 1¼ 2¾ 9 6 7⅛ 6 6 8 11 11 /16 26⅞ *7 10 3⅜ 8½ ½ ⅝ 11 16 1 11 /16 --- 1¼ 2¾ 9 6¼ 8 ¼ x ⅛ x 2¼ 1¼S 1½ 1¼ 8 11 11 /16 23⅛ 7 5⅜ 3⅜ 8½ ½ ⅝ 7¼ 13 1 11 /16 --- 1¼ 2¾ 6 3⅜ 4¾ 1½S 2 1½ 8 11 11 /16 23½ 7 5⅜ 3⅜ 8½ ½ ⅝ 7⅝ 12¾ 1 11 /16 --- 1¼ 2¾ 5¾ 3¾ 4¾ 1½M 2 1½ 8 11 11 /16 23⅝ 7 6⅜ 3⅜ 8½ ½ ⅝ 7¾ 13½ 1 11 /16 --- 1¼ 2¾ 6½ 3¾ 5¾ 1½L 2 1½ 8 11 11 /16 23⅝ 7 7⅜ 3⅜ 8½ ½ ⅝ 7¾ ½ 1 11 /16 --- 1¼ 2¾ 7½ 3¾ 6¾ 2S 2½ 2 8 11 11 /16 23¾ 7 5¾ 3⅜ 8½ ½ ⅝ 7⅞ 13¼ 1 11 /16 --- 1¼ 2¾ 6¼ 3⅞ 4¾ 2M 3 2 8 11 11 /16 23⅞ 7 6½ 3⅜ 8½ ½ ⅝ 8 1 11 /16 --- 1¼ 2¾ 7 3⅞ 5¾ (*) Suffi cient shims must be added for volute to clear fl oor NOTE: Flanged Connectors are special on size 2M and smaller. ¼ x ⅛ x 2¼ Customer Shop Order No. Date: By: Pump Motor Fig. No. Size Curve No. GPM Head Sp. Gr. Temp. Rotation Packing/Seal MFGR Hp RPM Phase-Cycle Voltage Frame Enclosure Insulation Furnished by Mounted 22 6/17

Fig. 4021 (or 4021H) - Sizes 1¼S, 1½S, 1½M, 1½L, 2S & 2M Pumps with Type C Drip Lip Steel Base, Coupling & Motor DIMENSIONS IN INCHES SIZE SUCT. DISCH. X Y Z CP HL 1¼S 1½ 1¼ 5½ 2 1 /16 4¾ 21¾ 5 7 /16 1½S 2 1½ 5¾ 2⅛ 4¾ 22 5 11 /16 1½M 2 1½ 6½ 2¼ 5¾ 22⅛ 5 13 /16 1½L 2 1½ 7½ 2¼ 6¾ 22⅛ 5 13 /16 2S 2½ 2 6¼ 2¼ 4¾ 22¼ 5 15 /16 2M 3 2 7 2½ 5¾ 22½ 6 3 /16 BASE DIMENSIONS IN INCHES FRAME NO 3T 5T 182T 184T 213T 215T 254T 256T 284TS 284T 286TS 286T BASE NO. 27501 27502 27502 27503 27503 27503 27504 27505 27504 27505 27505 27505 HA 12 12 12 12 12 12 15 15 15 15 15 15 HB 28 32 32 36 36 36 40 43 40 43 43 43 C 13⅛ 13⅛ ⅝ 15⅝ 17¾ 19¼ 22⅞ 24⅝ 24½ 25⅞ 26 27⅜ HD 10 10 10 10 10 10 10⅜ 10⅜ 10⅜ 10⅜ 10⅜ 10⅜ HE 4¾ 4¾ 4¾ 4¾ 4¾ 4¾ 6 6 6 6 6 6 HF 25½ 29½ 29½ 33½ 33½ 33½ 37½ 40½ 37½ 40½ 40½ 40½ HG 3 3 3 3 3 3 3⅜ 3⅜ 3⅜ 3⅜ 3⅜ 3⅜ HT ¾ ¾ ¾ ¾ ¾ ¾ 1 1 1 1 1 1 DISCHARGE POSITIONS SHOWN EACH 45 Customer Shop Order No. Date: By: Pump Motor Fig. No. Size Curve No. GPM Head Sp. Gr. Temp. Rotation Packing/Seal MFGR Hp RPM Phase-Cycle Voltage Frame Enclosure Insulation Furnished by Mounted 23

Fig. 4021 (or 4021H) - Sizes 3S, 3M, 4M, 4MS, 5M, 5MS, 6M & 6ML Sizes 1¼S, 1½S, 1½M, 1½L, 2S & 2M (Special Flanged) Pumps with Type C Drip Lip Steel Base, Coupling & Motor DIMENSIONS IN INCHES SUCTION 125LB DISCHARGE 125LB PUMP SIZE SIZE DIA. BOLTS BOLT SIZE DIA. BOLTS BOLT FLG. CIRCLE FLG. CIRCLE X Y Z CP HL S 1¼S 1½ 5 4 - ½ 3⅞ 1¼ 4⅝ 4 - ½ 3½ 6 3⅜ 4¾ 23⅛ 6 13 /16 --- 1½S 2 6 4 - ⅝ 4¾ 1½ 5 4 - ½ 3⅞ 5¾ 3¾ 4¾ 23½ 7 3 /16 --- 1½M 2 6 4 - ⅝ 4¾ 1½ 5 4 - ½ 3⅞ 6½ 3¾ 5¾ 23⅝ 7 5 /16 --- 1½L 2 6 4 - ⅝ 4¾ 1½ 5 4 - ½ 3⅞ 7½ 3¾ 6¾ 23⅝ 7 5 /16 2S 2½ 7 4 - ⅝ 5½ 2 6 4 - ⅝ 4¾ 6¼ 3⅞ 4¾ 23¾ 7 7 /16 --- 2M 3 7½ 4 - ⅝ 6 2 6 4 - ⅝ 4¾ 7 3⅞ 5¾ 23⅞ 7 9 /16 --- 3S 4 9 8 - ⅝ 7½ 3 7½ 4 - ⅝ 6 7 5⅞ 5¼ 26 9¾ --- 3M 4 9 8 - ⅝ 7½ 3 7½ 4 - ⅝ 6 8 5⅞ 6¼ 26 9¾ --- 4M, 4MS 5 10 8 - ¾ 8½ 4 9 8 - ⅝ 7½ 9 6⅛ 6½ 26⅝ 10 5 /16 ½ 5M, 5MS 6 11 8 - ¾ 9½ 5 10 8 - ¾ 8½ 9 6 7⅛ 26½ 10 3 /16 ½ 6M, 6ML 6 11 8 - ¾ 9½ 6 11 8 - ¾ 9½ 9 6¼ 8 26⅞ 10 9 /16 --- DISCHARGE POSITIONS SHOWN EACH 45 BASE DIMENSIONS IN INCHES FRAME NO 3T 5T 182T 184T 213T 215T 254T 256T 284TS 284T 286TS 286T 324TS 324T 326TS 326T 364TS 364T 365TS 365T BASE NO. 27501 27502 27502 27503 27503 27503 27504 27505 27504 27505 27505 27505 27507 27507 27507 27507 27507 27507 27507 27508 HA 12 12 12 12 12 12 15 15 15 15 15 15 18 18 18 18 18 18 18 18 HB 28 32 32 36 36 36 40 43 40 43 43 43 46 46 46 46 46 46 46 51 C 13⅛ 13⅛ ⅝ 15⅝ 17¾ 19¼ 22⅞ 24⅝ 24½ 25⅞ 26 27⅜ 27¼ 28¾ 28¾ 30¼ 31 33⅛ 32 34⅛ HD 10 10 10 10 10 10 10⅜ 10⅜ 10⅜ 10⅜ 10⅜ 10⅜ 12 12 12 12 13 13 13 13 HE 4¾ 4¾ 4¾ 4¾ 4¾ 4¾ 6 6 6 6 6 6 7½ 7½ 7½ 7½ 7½ 7½ 7½ 7½ HF 25½ 29½ 29½ 33½ 33½ 33½ 37½ 40½ 37½ 40½ 40½ 40½ 43½ 43½ 43½ 43½ 43½ 43½ 43½ 48½ HG 3 3 3 3 3 3 3⅜ 3⅜ 3⅜ 3⅜ 3⅜ 3⅜ 4 4 4 4 4 4 4 4 HT ¾ ¾ ¾ ¾ ¾ ¾ 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Customer Shop Order No. Date: By: Pump Motor Fig. No. Size Curve No. GPM Head Sp. Gr. Temp. Rotation Packing/Seal MFGR Hp RPM Phase-Cycle Voltage Frame Enclosure Insulation Furnished by Mounted 24

Fig. 4001, 4011, 4021 Selection Curves, 1750 & 3500RPM 25

Fig. 4011 & 4021 Selection Curve, 1150RPM 26

Fig. 4001 Sizes: 1" & 1½", 1750RPM 27

Fig. 4001 Sizes: 2½", 1750RPM 28

Fig. 4011 Sizes: 1¼S & 1½S, 1750RPM 29

Fig. 4011 & 4021 Sizes: 1½M & 2S, 1750RPM 30

Fig. 4011 & 4021 Sizes: 2M & 1½L, 1750RPM 31

Fig. 4011 & 4021 Sizes: 3S & 3M, 1750RPM 32

Fig. 4011 & 4021 Sizes: 4S & 4M, 1750RPM 33

Fig. 4021 Sizes: 5M & 5MS, 1750RPM 34

Fig. 4021 Sizes: 6M & 6ML, 1750RPM 35

Fig. 4001 Sizes: 1" & 1½", 3500RPM 36

Fig. 4001 & 4021H Sizes: 2½" & 1¼S, 3500RPM 37

Fig. 4011, 4021 & 4021H Sizes: 1½S & 2S, 3500RPM 38

Fig. 4021 & 4021H Sizes: 2M & 3M, 3500RPM 39

Fig. 4011 Sizes: 1¼S & 1½S, 1150RPM 40

Fig. 4011 & 4021 Sizes: 1½M & 1½L, 1150RPM 41

Fig. 4011 Sizes: 2S & 2M, 1150RPM 42

Fig. 4011 Sizes: 3S & 3M, 1150RPM 43

Fig. 4011 & 4021 Sizes: 4S & 4M, 1150RPM 44

Fig. 4021 Sizes: 5MS & 5M, 1150RPM 45

Fig. 4021 Sizes: 6M & 6ML, 1150RPM 46 6/09