Hydraulic Caliper Disc rakes SF Series SF SF 30 SF 1 SF 4 4 380 3 3 30 80 0 1 1 10 0 rake torque in knm DIN ISO 01 : 0 QA-Nr.: 0 1941 SF 80 UENZER REMSEN is certified according to DIN EN ISO 01:0 00 1 1 10 0 0 0 800 0 rake disc diameter in mm Reliable High Performance Robust Design Easy Maintenance 1
Description SF Main Features Two identical caliper halves, ready for operation, with spring packs set to nominal force and limit switch for release control Up to mm airgap between brake pad and disc Easy, manual pad wear compensation Organic, non-asbestos linings Options Limit switch wear control Sintered linings Complete piped supports for one or more calipers Hydraulic power units Special seals for flame-proof fluids Cleaning pads rake discs Applications Operating Restrictions The high capacity of these brakes makes them particularly suitable as secondary emergency brakes on hoist gears and on downhill conveyor belts. Other applications are possible in material handling, requiring power and compact design in either direction of rotation, particularly in replacing band brakes. rakes of this range are tested both mechanically and hydraulically and are set to nominal force. This setting can only be changed by the manufacturer. Operating conditions other than described in this brochure require the manufacturer s approval and may influence the function of the caliper and its components. Use of the brakes for applications with high duty cycles should be specifically indicated during technical selection procedure. Please Note ubenzer Service We supply a detailed operating manual with every order. Nevertheless, we would point out that brakes are only as safe as the servicing and maintenance performed while they are in operation. The guarantee for the correct functioning of our brakes is therefore only valid if the user adheres to the German DIN standard 1434 part (drum and disc brakes, servicing and maintenance in operation), or to comparable standards in his own country. This includes the verification of the brake selection, if required. A detailed questionnaire is provided for this purpose. Installation and commissioning on site is possible by ubenzer service engineers. Drawings as DWG/DXF files for your engineering department are available upon request.
Disc rake SF Dimensions and technical data Rev. 11-04 leeder valve Type SF 1 4 30 b 16 16 19 80 b 3 4 4 480 6 70 b 4 1 1 1 17 b b 6 11 8 11 8 0 1 0 1 b 7 70 1 1 b 8 8 8 0 1 1 b 9 b 10 170 Pressure connection c 1 d 17 17 3 d 6 d 7 31 38 0 d 8 1 1 1 1 1 h 1 70 70 480 h 0 0 30 37 h 3 70 0 1 l 1 68 70 8 9 981 l 9 9 34 0 l 3 0 0 1 1 l 4min 1 olt ø M4 M4 M30 M36 M48 olt material.9.9.9.9.9 Tighten. torque, Nm 0 0 0 300 6 Contact force F A kn 0 10 *) Average friction factor of standard material combination All dimensions in mm Alterations reserved without notice rake torque M r in Nm = F A (kn) x µ x d 1 (mm) Data per caliper half Op. pressure bar Max. pressure bar Release stroke mm Oil volume l Pad surface cm Theor. friction µ* Weight (kg) 1 0,03 47 0,03 47 0,03 70 368 0,00 0 7 0,0 13 1 8 1 rake disc data SF SF1 SF4 SF30 SF 7 3 d 1 = d -170 mm d -170 mm d - mm d - mm d -30 mm d 4 = d - mm d - mm d -4 mm d - mm d -700 mm 6 Please indicate mounting position in case of order. 4 d = rake disc diameter in mm d 1 = Friction diameter in mm d 4 = Max. permissible drum or hub diameter in mm b 1 = Disc thickness in mm (min. 30) 3
Disc rake SF Hydraulic power unit for one or more calipers Rev. 09-0 Standard configuration up to 4 SF/SF1 up to SF4 Motor: Pump: Pressure: Tank: 3 kw 9 l/min bar 30 l The flow diagram shows the general arrangement of the hydraulic power unit, including handpump for emergency manual release of the brakes. The two solenoid valves are switched in parallel (redundancy). After the nominal pressure is reached, the idler valve switches into idle running. The motor is continuously energized. Pressure switch, temperature switch, space heater and other accessories are available options. Hydraulic power unit limit All dimensions in mm Alterations reserved without notice With every order we supply a complete hydraulic and electric diagram according to the order specification. 4
Piping Samples Disc brakes SF and SC Rev. 09-0 Piping of one brake unit one hydraulic power unit Distributor rake Power Unit Pipe Piping of two brake units - one hydraulic power unit Distributor Pipe rake Power Unit Attention: For operating two brake units with one power unit please note, that the power unit should be installed in the middle between the brakes to get almost equal pipe length on both sides (equal apply time of brakes).