MAGNETO-INDUCTIVE POSITION DETECTORS

MAGNETO-INDUCTIVE POSITION DETECTORS Series 88 Type 2 wires APPLICATION This four-wire proximity sensor will monitor stroke end and intermediate positions of pneumatic cylinders equipped with built-in permanent magnets. Do not use near welding areas. OPERATING SYSTEM The permanent magnet is mounted in the piston head. On getting closer, its own magnetic fi eld generates variations of the current within the detector oscillator. An amplifi er converts them into switch signals. GENERAL CHARACTERISTICS Function : closing Switching voltage : 0 to 65 V DC Residual ripple : < 0% Residual current (opening) : < 0.8 ma Max. switching current : 00 ma Min. switching current : ma I L max. voltage drop : < 5 V Hysteresis : < mm Ambient temperature : -0 C ; 70 C DIAGRAM Housing : circuit protected by an aluminium box No serial connection can be performed with External protection : IP65 several detectors. Electrical protection : non-polarised detector protected against (-) 0 / 65 V = short circuits and overcharges (00 ma) : Load Connection (three possibilities) : 0.8 m cable four-pin male connector Ø 2 mm, - () CNOMO E0.62.520.N 2 m cable with stripped ends integrated male connector Ø 2 mm (for different extension cords available, see overleaf) Indicator lamp : diode (yellow LED) which lights up when the contact is closed Mounting direction : any way - Do not use near welding areas Mounting on cylinder : ISO 5552 - AFNOR NF ISO 5552 - DIN ISO 5552, type PES series 50 Ø 2 to 200 mm with tie rods and Ø 2 to 2m with profi led barrel. ISO 6 Ø 2 to 200 mm with tie rods, type TRINORM PIS series 6 CNOMO 06.07.02/0 - NFE 900/002 Ø 2 to 200 mm with tie rods, type TRINORM PCN series 7 B CHOICE OF EQUIPMENT Adaptation for CNOMO PCN Ø 2m cylinder : consult us DESCRIPTION Can be mounted CODE of one detector on cylinders with bracket on its own Inductive magnetic position detector, with wire 0.8 m long and four-pin male connector Ø 2 mm type conprox () to CNOMO with tie rods Ø 2 to 00 mm 88676 E0.0.50.N and E0.62.520.N, CNOMO cutting oil resistant wire, delivered with mounting bracket for cylinders: with tie rods Ø 25 to 200 mm 88678 88672 Inductive magnetic position detector, with wire 2 m long, stripped ends without connector, CNOMO cutting oil resistant wire, delivered with mounting bracket for cylinders: Inductive magnetic position detector, with integrated four-pin male connector Ø 2 mm (2) type conprox, delivered with mounting bracket for cylinders: with tie rods Ø 2 to 00 mm 88677 with tie rods Ø 25 to 200 mm 88679 with tie rods Ø 2 to 00 mm () Wires connected to pins and of the connector (car industry applications) (2) Wires connected to pins and of the connector In the case of use of a BIM magnetic detector on PES series 50 Ø 2, it is necessary to add the option code = 99525! Mounting on U or H guiding units: The forward position detector support is specified (consult us) 8867 8867 with tie rods Ø 25 to 200 mm 88680 8866 with profi led barrel Ø 2 to 2m 8868 Marking male connectors view from contact side () 2 (2) 2 Detector with wire Detector with integrated connector Extension cord (see Accessories overleaf) 0027GB-2006/R0 P297-

MAGNETO-INDUCTIVE DETECTORS ACCESSORIES-MOUNTINGS EXTENDING CORDS MOUNTING DEVICES DESCRIPTION CNOMO extension cord, cutting oil resistant wire conductors, 0.m 2 with fi ve-pin straight socket connector Ø 2 mm, CNOMO E0.62.520.N () (other end of wire stripped) Standard extension cord, wire conductors, 0.m 2 with four-pin straight socket connector Ø 2 mm (2) (other end of wire stripped) Standard extension cord, wire conductors, 0.m 2 with four-pin curved socket connector Ø 2 mm (2) (other end of wire stripped) Mounting device type KLI for cylinders with tie rods Ø 2 to 00 mm Mounting device type KLI for cylinders with tie rods Ø 25 to 200 mm Mounting device type KLI 2 for cylinders with profi led barrels Ø 2 to 2m () Wires connected to pins (brown) and (black) of the connector (2) Wires connected to pins (blue) and (black) of the connector DIMENSIONS AND WEIGHTS It is possible to install magnetic detectors to monitor stroke end or intermediate positions Detectors may be mounted on any of the tie rods or profi led barrels long long long MOUNTING ON CYLINDER WITH TIE RODS M2 CODE 88675 8869 88620 88625 8867 88626 MOUNTING ON CYLINDER WITH PROFILED BARREL M * M M 0 * Weight of detector bracket Dimensions cylinder Ø (mm) (mm) 2 0 50 6 80 00 25 60 200 M 6 50 5 58 65 72 8 97 M2 9 8 52 60 68 78 96 0 M 6 50 55 60 67 75 88 - - M 8 2 6 50 56 65 76 - - Weight* (in g) 67 MOUNTING ON CYLINDERS MOUNTING ON CYLINDERS WITH TIE RODS Ø 2 TO 200 mm Mounting Screw bracket MOUNTING ON CYLINDERS WITH PROFILED BARREL Ø 2 TO 2m Mounting bracket P297-2 Screw LED 2 2 LED Connection by compound-fi lled wire or male connector Ø 2 mm Connection by male connector Ø 2 mm Mounting instructions - Install mounting bracket on detector 2 - Start screwing in the detector - Position at measuring point - Check that the detector is in contact with the tube and tighten on cylinder, screwing down moderately with key (2.m hexagonal) Mounting instructions - Install mounting bracket on detector 2 - Start screwing bracket on detector - Position at measuring point - Check that the detector is in contact with the tube and tighten on cylinder, screwing down moderately with key (2.5 hexagonal) 0027GB-2006/R0 ASCO/JOUCOMATIC reserves the right to alter the availability, design and specifi cations without notice.

"COMPACT" MAGNETIC POSITION DETECTORS reed switch type FUNCTIONAL DESCRIPTION A permanent magnet (M) which is mounted on the piston of the air cylinder activates the reed switch of the non-contact magnetic position detector fastened on the outside of the non-magnetic cylinder barrel. REST POSITION DETECTED POSITION Series 88 Type 2 wires B (M) (M) DETECTOR CHARACTERISTICS MAX. SWITCHING POWER DC = W / AC =0 VA SWITCHING VOLTAGE MAX. SWITCHING CURRENT 2 to 0 VDC and AC 00 ma VOLTAGE DROP (EN 60.97-5-2) < 2,6 volt (I = 00mA) CONTACT RESISTANCE max. 0, ohm 0 V max. INSULATION RESISTANCE 2x0 6 ohm at 500 V WITHSTAND VOLTAGE 0 V AC and DC SENSITIVITY min. 2 mtesla (20 Gauss) RESPONSE TIME opening 0,2 ms closing 0,s REPEATABILITY ± 0,m LIFE 2x0 7 operations WORKING TEMPERATURE - 25 C, 70 C HOUSING Thermoplastic housing (PA-FV) with polyamide resin encapsulated printed circuit DEGREE OF PROTECTION (CE I 529) IP67 SIGNAL INDICATION Yellow diode (LED) which lights up when the contact is established lead, 2 or long, 2 wires 0. mm 2, stripped ends 0.8 m lead -pin plug-in male connector and Ø M8 0,8 m lead -pin screw-type male connec tor, Ø M8 0.8 m PUR lead -pin screw-type male connector, Ø M2 (2) ( possibilities / 5 types at choice) 2 metres etres Weight (g) 2 5 6 2 Compatible cylinders K KN PEC P2L - P2B PES 5 PESΩ (5) ISOCLAIR PES 50 PES 50, PESΩ (50), PCN with tie rods Reed switch type COMPACT detector mounting kit () (for direct mounting on cylinders with swallow tail grooves) Reed switch type COMPACT detector the mounting kit for each cylinder is ordered separately (see following pages) CODES 8820 88202 8820 88209 8820 () Detector supplied with mounting kit (special nut screw) for direct fi tting to cylinder grooves (2) PUR cable resistant to cutting fl uids ACCESSORIES AND OTHER ELECTRICAL CHARACTERISTICS: see following page 88 20 0V-00mA max. P29-0020GB-2005/R0

l (ma) DC 00 AC "COMPACT" DETECTORS - REED SWITCH TYPE MAXIMUM ELECTRICAL CHARACTERISTICS AND PROTECTION OF MAGNETIC DETECTOR (REED SWITCH) Note: The switching point must remain within the limits of the shaded area. Any excess voltage or power may damage the detector. INDUCTIVE RESISTIVE V R C 0 0 20 0 00 Ω W 0, μf 250 V 75 50 25 0 0 20 0 0 00 Ω W 0, μf 250 V Protection not necessary REED SWITCH : possibilities V View from male contact side of connector PARTICULAR APPLICATIONS (valid for all models) Detectors used for direct control of incandescent lamps: The capacity specifi ed on the lamp is based on its resistance when hot. When switched on, the resistance of the cold lamp is very low. Therefore, the current rises quickly and may exceed the reed switch rating. Allowance should therefore be made for the real power of the cold lamp. With leads longer than 0 m, a 000 Ω resistor must be fi tted in series with the detector to reduce the capacitive effect caused by the wiring. R = W resistor. Standard CCTU resistors code RP 59, C = paper, polycarbonate or metallized mylar capacitor. The user is responsible for supplying and assembling of components. The detectors reed switch are not polarized 0,8 m 0,8 m 2 / lead outlet Ø mm with stripped ends, 2 wires 0. mm 2 lead outlet Ø mm with -pin plug-in male connector screw Ø 8 mm (2 pins connected) 0,8 m lead outlet Ø mm with -pin screw-type male connector, Ø M8, VCS compatible (2 pins connected) PUR lead outlet Ø mm resistant to cutting fl uids, with -pin screw-type male connector, Ø M2 (2 pins connected) ACCESSORIES () Extension for M8 connector detectors. (2) Detector connection: brown and black wires (detector is unpolarised), blue wire not used () For your order please add the requested length (in metres) to the order code - example: 2 m = 8822 2 P29-2 Extension consisting of, length, wire conductors 0.2m 2 with screw-on femal M8 connector (other end plain) () (2) Extension consisting of, length, wire conductors 0.2m 2 with screw-on femal M2 connector (other end plain) (2) Straiht -pin female connector Ø M8, IP67 Right angle -pin female connector Ø M8, orientable 90 x 90, IP67 Cable cover and holder (sold by the metre - minimum length = m) br = blu= blk= br = blu= 2 blk= CODE 880029 880028 8800202 880020 8822 () 0020GB-2005/R0 ASCO/JOUCOMATIC reserves the right to alter the availability, design and specifi cations without notice.

"COMPACT" MAGNETIC POSITION DETECTORS magneto-resistive (MR) Series 88 Type wires PRINCIPLE Static non-contact proximity switch on air cylinders equipped with built-in permanent magnets. FUNCTIONAL DESCRIPTION When the permanent magnet which is mounted on the piston approaches the detector the magnetic fi eld it generates causes the semiconductors resistors to change. This current variation increases the resistance and a switching signal is generated. B DETECTOR CHARACTERISTICS MAX. SWITCHING POWER W SWITCHING VOLTAGE 0 to 0 VDC MAX. SWITCHING CURRENT 00 ma PNP VOLTAGE DROP (EN 60.97-5-2) <, volt (I = 50 ma) VOLTAGE DROP (EN 60.97-5-2) <,2 volt (I = 00 ma) MAX: LEAKAGE CURRENT 0 µa MAX. ALLOWABLE OVERVOLTAGE max. 0 volt (0 seconds) INSULATION RESISTANCE (500V) 20x0 6 ohm SENSITIVITY min. 2 mtesla (20 Gauss) RESPONSE TIME opening 0,2 ms closing 0, ms REPEATABILITY ± 0, mm LIFE 5x0 7 operations WORKING TEMPERATURE - 25 C, 70 C ELECTRICAL PROTECTION Polarized detector, protectec against short-circuits and overs (see opposite) HOUSING Thermoplastic housing (PA-FV) with polyamide resin encapsulated printed circuit DEGREE OF PROTECTION (CE I 529) IP67 SIGNAL INDICATION Yellow diode (LED) which lights up during switching lead, 2 or long, wires 0. mm 2, stripped ends 0,8 m lead -pin plug-in male connector and Ø M8 0,8 m lead -pin screw-type male connec tor, Ø M8 0,8 m PUR lead -pin screw-type male connector, Ø M2 (2) ( possibilities / 5 types at choice) Compatible cylinders K KN PEC P2L - P2B PES 5 PESΩ (5) Magneto-resistive type COMPACT detector mounting kit () (for direct mounting on cylinders with swallow tail grooves) 2 metres etres Weight (g) 2 5 6 2 CODES 88205 88206 88207 8820 88208 ISOCLAIR PES 50 Magneto-resistive type COMPACT detector PES 50, the mounting kit for PESΩ (50), each cylinder is ordered separately (see PCN with tie rods following pages) () Detector supplied with mounting kit (special nut screw) for direct fi tting to cylinder grooves (2) PUR cable resistant to cutting fl uids ACCESSORIES AND OTHER ELECTRICAL CHARACTERISTICS: see following page 88 20 0V-00mA max. P29-00205GB-2005/R0

"COMPACT" DETECTORS - MAGNETO-RESISTIVE (MR) ELECTRICAL PROTECTION Output protected against short-circuit as long as the output current is restricted to 0. A. Improper wire connection may prevent the detector from operating or even destroy it. It is recommended to install a protection diode (mounted in parallel) on an inductive in spite of the internal protection. (PNP) () (--) brown blue black Polarities to be observed! OF MAGNETO-RESISTIVE DETECTORS: possibilities View from male contact side of connector 0,8 m 2 / lead outlet Ø mm, stripped ends wires 0. mm 2 - Brown wire : Blue wire : - Black wire : 0,8 m lead outlet Ø mm with -pin plug-in male connector screw Ø M8 0,8 m lead outlet Ø mm with -pin screw-type male connector Ø M8, VCS compatible ACCESSORIES P29- Extension consisting of, length, wire conductors 0.2m 2 with screw-on femal M8 connector (other end plain) () (2) Extension consisting of, length, wire conductors 0.2m 2 with screw-on femal M2 connector (other end plain) (2) Straiht -pin female connector Ø M8, IP67 Right angle -pin female connector Ø M8, orientable 90 x 90, IP67 Cable cover and holder (sold by the metre - minimum length = m) PUR lead outlet Ø mm resistant to cutting fl uids, with -pin screw-type male connector Ø M2 () Extension for M8 connector detectors. (2) Detector connection, brown wire =, blue wire = -, black wire = () For your order please add the requested length (in metres) to the order code - example: 2 m = 8822 2 br = blu= blk= br = blu= 2 blk= CODE 880029 880028 8800202 880020 8822 () 00205GB-2005/R0 ASCO/JOUCOMATIC reserves the right to alter the availability, design and specifi cations without notice.

"T SLOT" MAGNETIC POSITION DETECTORS reed switch type for series 5 PES type cylinders Series 88 Type 2 wires FUNCTIONAL DESCRIPTION A permanent magnet (M) which is mounted on the piston of the air cylinder activates the reed switch of the non-contact magnetic position detector fastened on the outside of the non-magnetic cylinder barrel. REST POSITION DETECTED POSITION B (M) (M) DETECTOR CHARACTERISTICS MAX. SWITCHING POWER 6 W SWITCHING VOLTAGE 0 to 0 VDC and AC MAX. SWITCHING CURRENT 200 ma VOLTAGE DROP (EN 60.97-5-2) < volt (I = 200mA) CONTACT RESISTANCE max. 0,5 Ω INSULATION RESISTANCE > 00 MΩ WITHSTAND VOLTAGE 200 V DC SENSITIVITY min. 2,Tesla (25 Gauss) RESPONSE TIME opening 0, ms closing 0, ms REPEATABILITY ± 0,m LIFE 0 7 operations (resistive ) WORKING TEMPERATURE - 5 C, 70 C HOUSING Thermoplastic housing (PA) with epoxy resin encapsulated printed circuit DEGREE OF PROTECTION (CE I 529) IP67 SIGNAL INDICATION orange diode (LED) which lights up when the contact is established lead, 2 m long, 2 wires 0. mm 2, stripped and tinned ends lead, long, 2 wires 0. mm 2, stripped and tinned ends 0, lead -pin plug-in male connector and Ø M8 0. lead -pin screw-type male connec tor, Ø M2 ( possibilities / types at choice) 2 metres etres Weight (g) 2 5 7 Compatible CODES cylinders PES series 5 Reed switch type "T" detector mounting kit () (for direct mounting on cylinders with "T" slot) 88007 88007 880075 880076 () Detector supplied with mounting kit (integrated) for direct fi tting to cylinder grooves ACCESSORIES AND OTHER ELECTRICAL CHARACTERISTICS: see following page P292-0028GB-2005/R0

MAXIMUM ELECTRICAL CHARACTERISTICS AND PROTECTION OF MAGNETIC DETECTOR (REED SWITCH) l (ma) DC 200 AC "T SLOT" DETECTORS - REED SWITCH TYPE Note: The switching point must remain within the limits of the shaded area. Any excess voltage or power may damage the detector. INDUCTIVE RESISTIVE Load Load V R C 0 0 20 0 00 Ω W 0, μf 250 V 50 00 50 0 0 20 0 0 00 Ω W 0, μf 250 V Protection not necessary V PARTICULAR APPLICATIONS (valid for all models) Detectors used for direct control of incandescent lamps: The capacity specifi ed on the lamp is based on its resistance when hot. When switched on, the resistance of the cold lamp is very low. Therefore, the current rises quickly and may exceed the reed switch rating. Allowance should therefore be made for the real power of the cold lamp. With leads longer than 0 m, a 000 W resistor must be fi tted in series with the detector to reduce the capacitive effect caused by the wiring. R = W resistor. Standard CCTU resistors code RP 59, C = paper, polycarbonate or metallized mylar capacitor. The user is responsible for supplying and assembling of components. REED SWITCH : possibilities 2 / 0, 0, View from male contact side of connector lead outlet Ø mm with stripped ends, 2 wires 0. mm 2 The detectors reed switch are not polarized (Diode polarized) lead outlet Ø mm with -pin plug-in male connector screw Ø M8 (2 pins connected) lead outlet Ø mm with -pin screw-type male connector, Ø M2 (2 pins connected) brown blue - ACCESSORIES Extension cord made of, length, wires 0.2m 2 with screw-type female M8 connector (other end stripped) () (2) Extension cord made of, length, wires 0.2m 2 with screw-type female M2 connector (other end stripped) (2) Straight -pin female connector Ø M8, IP67 Right angle -pin female connector Ø M8, orientable 90 x 90, IP67 Cable cover and holder (sold by the metre - minimum length = m) br = blu= blk= br = blu= 2 blk= () Extension for M8 connector detectors. (2) Detector connection: brown and black wires (detector is unpolarised), blue wire not used () For your order please add the requested length (in metres) to the order code 880076. Example: 2 m = 880076 2 CODE 880029 880028 8800202 880020 880076 () 2, = 880076 DIMENSIONS The magnetic detector fi ts directly into the grooves in the cylinder body. Detection of very small movements or very short strokes means that more than one groove will have to be used. 5 INSTALLATION RECOMMENDATION In order to control the max. end of cylinder stroke, the detectors must be mounted in the following direction: PES cylinders series 5 Ø 2-00 : cable oriented towards the cylinder barrel. P292-2 0028GB-2005/R0 ASCO/JOUCOMATIC reserves the right to alter the availability, design and specifi cations without notice.

"T SLOT" MAGNETIC POSITION DETECTORS magneto-resistive (MR) for series 5 PES type cylinders Series 88 Type wires PRINCIPLE Static non-contact proximity switch on air cylinders equipped with built-in permanent magnets. FUNCTIONAL DESCRIPTION When the permanent magnet which is mounted on the piston approaches the detector the magnetic fi eld it generates causes the semiconductors' resistors to change. This current variation increases the resistance and a switching signal is generated. B DETECTOR CHARACTERISTICS MAX. SWITCHING POWER W SWITCHING VOLTAGE 0 to 0 VDC MAX. SWITCHING CURRENT 200 ma PNP N.O. VOLTAGE DROP (EN 60.97-5-2) < 0,7 volt (I = 200 ma) INSULATION RESISTANCE > GΩ SENSITIVITY min. 2,Tesla (25 Gauss) RESPONSE TIME opening 0,8 µs closing 0, µs REPEATABILITY ± 0,2 mm LIFE 0 operations (resistive ) WORKING TEMPERATURE - 5 C, 80 C ELECTRICAL PROTECTION Polarized detector, protectec against short-circuits and overs (see opposite) HOUSING Thermoplastic housing (PA) with epoxy resin encapsulated printed circuit DEGREE OF PROTECTION (CE I 529) IP67 SIGNAL INDICATION orange diode (LED) which lights up during switching lead, 2 m long, wires 0. mm 2, stripped and tinned ends lead, long, wires 0. mm 2, stripped and tinned ends 0, lead -pin plug-in male connector and Ø M8 0, PCV lead - pin screw-type male connec tor, Ø M2 ( possibilities / types at choice) Magneto-resistive type "T" detector mounting kit () (for direct mounting on cylinders with "T" slot) 2 metres etres Weight (g) 2 5 7 Compatible cylinders CODES PES series 5 Coaxial valve series 287-87 () Detector supplied with mounting (integrated) kit for direct fi tting to cylinder grooves 880077 880078 880079 880070 ACCESSORIES AND OTHER ELECTRICAL CHARACTERISTICS: see following page P292-0029GB-2005/R0

ELECTRICAL PROTECTION Improper wire connection may prevent the detector from operating or even destroy it. "T SLOT" DETECTORS - MAGNETO RESISITIVE TYPE (PNP) () (--) brown blue black Polarities to be observed! OF MAGNETO-RESISTIVE DETECTORS: possibilities View from male contact side of connector 0, 2 / lead outlet Ø mm, stripped ends wires 0. mm 2 - Brown wire : Blue wire : - Black wire : 0, lead outlet Ø mm with -pin plug-in male connector screw Ø M8 (2 pins connected) lead outlet Ø mm with -pin screw-type male connector Ø M2 ACCESSORIES Extension cord made of, length, wires 0.2m 2 with screw-type female M8 connector (other end stripped) () (2) Extension cord made of, length, wires 0.2m 2 with screw-type female M2 connector (other end stripped) (2) br = blu= blk= br = blu= 2 blk= CODE 880029 880028 Straight -pin female connector Ø M8, IP67 8800202 Right angle -pin female connector Ø M8, orientable 90 x 90, IP67 Cable cover and holder (sold by the metre - minimum length = m) () Extension for M8 connector detectors. (2) Detector connection, brown wire =, blue wire = -, black wire = () For your order please add the requested length (in metres) to the order code 88 00 76. Example: 2 m = 880076 2 2, = 880076 DIMENSIONS The magnetic detector fi ts directly into the grooves in the cylinder body. Detection of very small movements or very short strokes means that more than one groove will have to be used. P292-5 880020 880076 () INSTALLATION RECOMMENDATION In order to control the max. end of cylinder stroke, the detectors must be mounted in the following direction: PES cylinders series 5, Ø 2-00 : cable oriented towards the cylinder barrel 0029GB-2005/R0 ASCO/JOUCOMATIC reserves the right to alter the availability, design and specifi cations without notice.

"UNI" MAGNETIC POSITION DETECTORS reed switch type Series 88 Type 2 wires FUNCTIONAL DESCRIPTION A permanent magnet (M) which is mounted on the piston of the air cylinder activates the reed switch of the non-contact magnetic position detector fastened on the outside of the non-magnetic cylinder barrel. REST POSITION DETECTED POSITION 88000 60V-500mA max. 88002 60V-500mA max. B (M) DETECTOR CHARACTERISTICS (M) 00207GB-2008/R0 Availability, design and specifications are subject to change without notice. All rights reserved. MAX. SWITCHING POWER DC = 0 W / AC = 2 VA SWITCHING VOLTAGE 0 to 60 V DC and AC MAX. SWITCHING CURRENT 500 ma 60 V () VOLTAGE DROP (EN 60.97-5-2) < 2.7 volt (I = 200mA) max. < 2.9 volt (I = 500mA) CONTACT RESISTANCE max. 0. ohm INSULATION RESISTANCE 0 0 ohm WITHSTAND VOLTAGE DC = 70 V - AC = 600 V SENSITIVITY min. mtesla (0 Gauss) RESPONSE TIME opening 0.2 ms closing 0.6 ms REPEATABILITY ± 0. mm LIFE 0 7 operations WORKING TEMPERATURE -20 C, 70 C HOUSING Thermoplastic housing (PPS) with expoxy resin encapsulated printed circuit DEGREE OF PROTECTION (CE I 529) IP67 SIGNAL INDICATION Green diode (LED) which lights up when the contact is established (5 possibilities / 6 types at option) Integrated connector -pin screw-type male connector, Ø M8 lead, 2 or long, 2 wires 0. mm 2, stripped ends 0.8 m lead -pin plug-in male connector, Ø 8 UNI detector supplied with mounting kit (special nut screw) for direct fi tting to cylinder grooves () Version for 20 V AC/DC max. (50 ma -.5 VA), on request, with 2 m PUR cable, detector only, code: 88008 detector mini mounting kit ( ), code: 88007 ACCESSORIES AND OTHER ELECTRICAL CHARACTERISTICS: see opposite MOUNTING KITS, INSTALLATION ON CYLINDERS: see following pages 5 lead outlet protected by feed-through sleeve 0.8 m lead -pin screw-type male connec tor, Ø M2 Recommendation for application For cylinder detector applications with long travels and large movements you must use the mini-detector with M8 connector integrated in the housing and lead outlets with cable (2- or - wire) type class 6 especially intented for this purpose (specifi c accessory: consult us) 2 metres etres Weight (g) 6 0 70 22 86 5 Compatible cylinders CODES CAS - CIS CIB PES-PES Ω 50 PCN TUB R - RS K KN PEC P2L - P2B PES-PES Ω 5 Reed switch type UNI detector only the mounting kit for each cylinder is ordered separately (see following pages) Reed switch type UNI detector mounting kit ( ) (for direct mounting on cylinders with swallow tail grooves) 88000 60V-500mA max. 88002 60V-500mA max. 88000 88002 8800 88006 880059 88008 88006 60V-500mA max. lead -pin screw-type male connec tor, Ø M8 88008 60V-500mA max. 880085 880086 880089 880090 8800592 88009 880059 60V-500mA max. All leafl ets are available on: www.asconumatics.eu P295-

"UNI" DETECTORS - REED SWITCH TYPE MAXIMUM ELECTRICAL CHARACTERISTICS AND PROTECTION OF MAGNETIC DETECTOR (REED SWITCH) Note: The switching point must remain within the limits of the shaded area. Any excess voltage or power may damage the detector. INDUCTIVE RESISTIVE V R C 60 V max. models 20 V max. (AC/DC) model l (ma) Max. power =,5 VA (50 ma max.) Life = 0 6 operations DC 500 AC To obtain the maximum service life, there should be no arcing betwen contacts. The voltage and current values indicated must 00 therefore not be exceeded. In the case of electrical circuits with induction coils, protection 00 devices should be used to absorb cut-off overvoltage. The ideal protection component is the varistor (507K250). 200 60 5 2 220 Ω W 5 00 Ω W 0, μf/250 V 00 0 5 0 5 60 00 Ω W 0, μf 250 V Protection not necessary V Varistor R = W resistor. Standard CCTU resistors code RP 59, C = paper, polycarbonate or metallized mylar capacitor. The user is responsible for supplying and assembling of components. Inductive PARTICULAR APPLICATIONS (valid for all models) Detectors used for direct control of incandescent lamps: The capacity specifi ed on the lamp is based on its resistance when hot. When switched on, the resistance of the cold lamp is very low. Therefore, the current rises quickly and may exceed the reed switch rating. Allowance should therefore be made for the real power of the cold lamp. With leads longer than 0 m, a 000 Ω resistor must be fi tted in series with the detector to reduce the capacitive effect caused by the wiring. REED SWITCH : 5 possibilities View from male contact side of connector The UNI detectors reed switch are not polarized -pin screw-type male connector Ø M8 (2 pins connected) 2 / 0.8 m Lead outlet Ø mm with stripped ends, 2 wires 0. mm 2 Lead outlet Ø mm with -pin plug-in male connector, Ø 8 mm (2 pins connected) ACCESSORIES () Extension for integral M8 connector detectors. Coupling to snap-on Ø 8 male connectors is not advised. (2) Detector connection: brown and black wires (detector is unpolarised), blue wire not used All leafl ets are available on: www.asconumatics.eu P295-2 0.8 m Extension consisting of, length, wire conductors 0.2m 2 with screw-on femal M8 connector (other end plain) () (2) Extension consisting of, length, wire conductors 0.2m 2 with screw-on femal M2 connector (other end plain) (2) Straiht -pin female connector Ø M8, IP67 Right angle -pin female connector Ø M8, orientable 90 x 90, IP67 Lead outlet Ø mm with -pin screw-type male connector, Ø M8 (2 pins connected) (adaptable on inputs VCS connectors) Lead outlet Ø mm with -pin screw-type male connector, Ø M2 (2 pins connected) br = br = blu= blk= blu= 2 blk= CODE 880029 880028 8800202 880020 00207GB-2006/R0 Availability, design and specifications are subject to change without notice. All rights reserved.

"UNI" MAGNETIC POSITION DETECTORS magneto-resistive (MR) Series 88 Type wires PRINCIPLE Static non-contact proximity switch on air cylinders equipped with built-in permanent magnets. 8800 0V-200mA max. MR FUNCTIONAL DESCRIPTION When the permanent magnet which is mounted on the piston approaches the detector the magnetic fi eld it generates causes the semiconductors' resistors to change. This current variation increases the resistance and a switching signal is generated. 8800 0V-200mA max. MR B DETECTOR CHARACTERISTICS MAX. SWITCHING POWER 6 W SWITCHING VOLTAGE 0 to 0 V DC MAX. SWITCHING CURRENT 200 ma PNP VOLTAGE DROP <. Volt (I = 50 ma) <. Volt (I = 200 ma) MAX: LEAKAGE CURRENT 0 µa MAX. ALLOWABLE OVERVOLTAGE 50 Volt (0 seconds) INSULATION RESISTANCE 0 0 ohm SENSITIVITY min. mtesla (0 Gauss) RESPONSE TIME opening 0.2 ms closing 0. ms REPEATABILITY ± 0. mm WORKING TEMPERATURE -20 C, 70 C ELECTRICAL PROTECTION Polarized detector, protectec against short-circuits and overs (see opposite) and incorporated recovery diode HOUSING Thermoplastic housing (PPS) with epoxy resin encapsulated printed circuit DEGREE OF PROTECTION (CE I 529) IP67 SIGNAL INDICATION Green diode (LED) which lights up during switching (5 possibilities / 6 types at option) Integrated connector -pin screw-type male connector, Ø M8 lead, 2 or long, wires 0. mm 2, stripped ends 5 lead outlet protected by feed-through sleeve 0.8 m lead -pin plug-in male connector, Ø 8 lead -pin screw-type male connec tor, Ø M8 0.8 m lead -pin screw-type male connec tor, Ø M2 00208GB-2008/R0 Availability, design and specifi cations are subject to change without notice. All rights reserved. Recommendation for application For cylinder detector applications with long travels and large movements you must use the mini-detector with M8 connector integrated in the housing and lead outlets with cable (- wire) type class 6 especially intented for this purpose (specifi c accessory: consult us) Detector supplied with mounting kit (special nut screw) for direct fi tting to cylinder grooves ACCESSORIES AND OTHER ELECTRICAL CHARACTERISTICS: see opposite MOUNTING KITS, INSTALLATION ON CYLINDERS: see following pages 8800 0V-200mA max. MR Weight (g) 6 0 70 22 86 5 Compatible cylinders CAS - CIS CIB PES-PES Ω 50 PCN TUB R - RS K KN PEC P2L - P2B PES-PES Ω 5 Magneto-resistive type UNI detector only the mounting kit for each cylinder is ordered separately (see following pages) Magneto-resistive type UNI detector mounting kit ( ) (for direct mounting on cylinders with swallow tail grooves) 8800 0V-200mA max. MR 2 metres etres 88007 0V-200mA max. CODES 8800 8800 88005 88007 8800595 88009 880092 88009 88009 880095 880059 880096 MR 8800595 0V-200mA max. 88009 0V-200mA max. All leafl ets are available on: www.asconumatics.eu MR MR P295-

"UNI" DETECTORS - MAGNETO-RESISTIVE (MR) ELECTRICAL PROTECTION Output protected against short-circuit as long as the output current is restricted to 0.2 A. Improper wire connection may prevent the detector from operating or even destroy it. It is recommended to install a protection diode (mounted in parallel) on an inductive in spite of the internal protection. (PNP) () (--) brown blue black Polarities to be observed OF MAGNETO-RESISTIVE DETECTORS: 5 possibilities View from male contact side of connector 0.8 m 2 / -pin screw-type male connector Ø M8 - pins Lead outlet Ø mm, stripped ends wires 0. mm 2 - Brown wire : Blue wire : - Black wire : Lead outlet Ø mm with -pin plug-in male connector Ø 8 mm 0.8 m Lead outlet Ø mm with -pin screw-type male connector Ø M8 (adaptable on inputs VCS connectors) Lead outlet Ø mm with -pin screw-type male connector Ø M2 ACCESSORIES () Extension for integral M8 connector detectors. Coupling to snap-on Ø 8 male connectors is not advised. (2) Detector connection, brown wire =, blue wire = -, black wire = All leafl ets are available on: www.asconumatics.eu P295- Extension consisting of, length, wire conductors 0.2m 2 with screw-on femal M8 connector (other end plain) () (2) Extension consisting of, length, wire conductors 0.2m 2 with screw-on femal M2 connector (other end plain) (2) Straiht -pin female connector Ø M8, IP67 Right angle -pin female connector Ø M8, orientable 90 x 90, IP67 br = br = blu= blk= blu= 2 blk= CODE 880029 880028 8800202 880020 00208GB-2006/R0 Availability, design and specifications are subject to change without notice. All rights reserved.