BUTT-N-TOP GRAPPLE Weldco-Beales Manufacturing s Butt-n-Top Grapples load, unload, sort, and pile tree length wood with a log loader or standard excavator machine configuration. FEATURES & BENEFITS: Individually controlled hydraulic outriggers stabilize load Strong light weight body Large diameter pins for greater durability Powerful sorting or bunching jaws 360-degree continuous rotation Totally enclosed for internal component protection Enables loading from the side or rear Outriggers provide easier level loading Maximum productivity of excavator/log loader STANDARD SPECIFICATIONS: Tilt cylinder turret Pivot frame Four heavy-duty cylinders Two outriggers, Two jaws High pressure swivel Pin-on lugs Tilt cylinder and cylinder anchor Rugged, high torque motors OPTIONS: Valve-in-head Chain drive or gear drive Cut-off saw V or U shaped outriggers Bunching or Sorting jaws Bucket linkage lugging Shortwood jaw option Extended tool cylinder to use factory cylinder anchor with removal of bucket linkage Continued on next page»
FEATURES AND SPECIFICATIONS: DIMENSIONS (INCHES) MODEL A B C D E F G H J K XG-300 14 46 69 17 24 22 40 70 116 24 XG-400 15 52 74 21 26 27 41 70 116 24-1/2 B XG-500 S 18-1/4 14 66-1/2 64 86 83 24-1/2 21 25-1/2 30-1/2 50 50 81-1/2 81-1/2 127 127 B XG-600 S 19 15-1/2 69-1/2 68 91 87 26-1/2 25 30 36 34 33 50 50 81-1/2 81-1/2 127 127 XG-700 25 77 103 32 33-1/2 38-1/2 50-1/2 89 150 XG-800 25 77 104 32 36 39 52 89 150 Weights and specifications are approximate and subject to change without notice.
CLAM GRAPPLE Weldco-Beales Manufacturing s Clam Grapple is a versatile tool, offering 360 of rotation. It is normally configured with loader jaws and is used for log loading and handling. FEATURES & BENEFITS: Performs digging, loading brush piling, and log loading operations, depending on jaw type Pin-on or Quick Coupler connections 360 continuous rotation with dual high torque drive motors for load holding and handling May be used on log loader booms with optional tilt cylinder Configuration versatility to handle a variety of applications Large diameter rotation bearing for power tilting (heeling) Interchangeable jaw between series Dual drive high torque motors 6 Port hydraulic swivel Rotation soft start Bolt-on mount for fixed or hydraulic outrigger Quick change or pin-on style lugging Weld-on jaw tips High pressure cylinders OPTIONAL EQUIPMENT: Hydraulic outrigger(s) Fixed outrigger Shortwood jaws Clamshell buckets Butt-n-top jaws Control valve in head (2,3 or 4 Section) Cut-off saw Heavy duty tilt cylinder Rotate float Jaw timing link Trailer lifting hook Continued on next page»
MACHINE SIZE MODEL JAW TYPE BEARING DIA. (IN.) Series EX 200 Series EX 250 Series EX 300 Series EX 400 WIDTH (IN.) OPENING (IN.) CLOSED (IN.) CAPACITY (CU.YD.) CAPACITY (SQ.FT) WEIGHT (LBS.) XPC-500 LOADER 27.1 42 75 7-5.29 3900 XPC-500S SHORTWOOD 27.1 42 84 7-3/4-10 4300 XPC-500B BUCKET 27.1 36 90-3/4-4200 XPC-500 LOADER 27.1 42 75 7-5.29 3900 XPC-500S SHORTWOOD 27.1 42 92 7-3/4-12.72 4400 XPC-500B BUCKET 27.1 40 90-7/8-4300 XPC-600 LOADER 33.6 42 78 7-6.24 4500 XPC-600S SHORTWOOD 33.6 42 96 8-14 5000 XPC-600B BUCKET 33.6 42 115-1-1/4-5200 XPC-600 LOADER 33.6 42 81 7-7.2 4600 XPC-600S SHORTWOOD 33.6 42 102 8-16 5100 XPC-600B BUCKET 33.6 48 115-1-1/2-5400 *Cord Capacity = Capacity (Sq.Ft.) X Wood Length (Ft.) X.8 Fill Factor X.0078 Cubic Meter Capacity = Capacity (Sq. Ft.) X Wood Length (Ft.) X.8 Fill Factor X.0283 FEATURES: Flexible jaw configuration Superior loading and brush piling performance Excellent load handling with 360 continuous rotation and dual high torque drive motors Pin-on or Quick Coupler compatibility Log loader boom compatibility with optional tilt cylinder Large diameter rotation bearing supports power tilting (heeling)
EXCAVATOR HEEL GRAPPLE Weldco-Beales Manufacturing s Heel Grapple is specifically designed for loading, sorting, decking, and hoe-chucking (shoved, forwarding) tree length wood. FEATURES & BENEFITS: 360 continuous gear drive rotation Equipped with cross over relief valves Hydraulic motor, hose, and cylinder protection 100,000 psi steel plate jaws Available in various jaw configurations and sizes Easier penetration of log piles Tight closure for smaller wood Good versatility for both large and small wood Durable, tough design STANDARD SPECIFICATIONS: Knuckle Turret Bearing with single motor and gear drive By-pass jaws with single pin OPTIONS: Heel cylinder (live heel)
SHORTWOOD/PULPWOOD GRAPPLE - DANGLING Weldco-Beales Manufacturing s Shortwood/Pulpwood Grapples - Dangling are primarily used in loading and unloading of cut to length wood. FEATURES AND BENEFITS 360 continuous rotation Heavy-duty construction High strength, high capacity box-type jaws Heavy-duty chain to weigh down load (on tip-to-tip jaws) Timing link to synchronize jaws (on bypass jaws) Proven jaw profile maximizes capacity, increases productivity, and reduces loading cycles Heavy-duty construction promotes durability in a harsh environment STANDARD SPECIFICATIONS Turret Pivot frame Two heavy-duty cylinders Shortwood jaws Butt plates Choice of bypass jaws complete with timing link(s), or tip-to-tip jaws complete with load chain Continued on next page»
BYPASS JAWS TIP TO TIP JAWS
EXTREME SERVICE HEEL GRAPPLE Weldco-Beales Manufacturing s Extreme Service Heel Grapple is specially designed to hoe-chuck (forward) large trees and is ideal for logging in difficult terrain. FEATURES & BENEFITS: Continuous 360 gear drive rotation Heavy-duty construction Fully protected hydraulic swivel, hoses, and cylinders 100,000 psi steel jaws High abrasion resistant solid steel tips for longer life Available in various jaw configurations and sizes Long life durability Efficiently rear loads and hoe chucks Designed to reduce log damage STANDARD SPECIFICATIONS: Heel Knuckle Turret Bearing with single motor and gear drive Heavy-duty by-pass jaws with two pins* Cylinder guards* Heavy-duty pin retainers* * Denotes options that make the Extreme Service Grapple more robust than a regular Heel Grapple. OPTIONS: Heel cylinder (live heel) Continued on next page»
GRAPPLE SIZE 60 66 72 AI - Open 60 66 72 A2 - Closed 7 7 7 B1 - Height Open 81-1/2 83-1/16 86-1/2 B2 - Height Closed 84-3/4 88-3/8 93 C1 - Inside Jaw Width 11-1/4 11-1/4 11-1/4 C2 - Outside Jaw Width 16-3/4 16-3/4 16-3/4 C3 - Body Width 20-5/8 20-5/8 20-5/8 Weight 3000 00 3225
MAG GRAB GRAPPLE (MG 50 / 75 / 100 / 125 / 150) Our MagGrab is ideal for single crane scrap yards providing 100% handling of all incoming & outgoing ferrous scrap. STANDARD SPECIFICATIONS: 360 continuous rotation. High Torque reversing drive motor comes with an integral relief valve. Slew ring and pinion fully guarded to prevent damage and contamination. High pressure, low friction rotary swivel seals, with J-style back up rings. Cylinder hoses are routed internally to prevent damage during operation. Open framework design gives easy access to cylinders, hoses and fittings. Heavy Duty Aluminum wound Ohio brand magnet rated at 4 kw. Custom designed corner dowels eliminate loose magnet Magnet slip rings rated for 60W / 230 VAC. Tines have deep box section construction with AR400 steel in high wear areas. Mechanical tine stops limit cylinders stress.
MAG GRAB GRAPPLE Grapple Model Magnet Size (in.) Grapple Capacity (yd 3 ) Grapple Capacity (m 3 ) Closed Height (in.) A Open Height (in.) B Jaw Opening (in.) C Outside Width (in.) D Grapple Weight (lbs.) MG50-30 30 ½ 0.38 80 56 84 62 3700 MG75-30 30 ¾ 0.57 87 66 92 67 3850 MG75-36 36 ¾ 0.57 87 66 92 67 4000 MG100-36 36 1 0.76 90 66 98 73 4900 MG100-40 40 1 0.76 90 68 98 73 5400 MG125-40 40 1 ¼ 0.96 97 68 112 83 5700 MG150-44 44 1 ½ 1.15 100 74 118 88 6700 MG150-50 50 1 ½ 1.15 100 74 118 88 7800