The multi-function machine

The multi-function machine Technical Description Multi

Clamping unit asic hydraulic 500 kn 800 kn 1100 kn 18,5 kw 22 kw 30 kw Injection unit/ Distance Screw between tie bars V V V 370 x 370 120 200 22/25/30 25/30/35 35 80 120 14/18 18/22 22/25 420 x 420 120 200 310 22/25/30 25/30/35 30/35/40 35 80 120 200 14/18 18/22 22/25 25/30 470 x 470 310 430 30/35/40 35/40/45 35 80 120 200 310 14/18 18/22 22/25 25/30 30/35 Clamping unit asic hydraulic 1250 kn 1500 kn 2000 kn 30 kw 30 kw 37 kw Injection unit/ Distance Screw between tie bars V+ V++R V++R 475 x 450 500 x 500 320 440 22/25/30 25/30/35 35 80 120 200 310 430 14/181) 18/22 22/25 25/30 30/35 35/40 440 610 25/30/35 40/45/50 35 80 120 200 310 430 14/181) 18/22 22/25 25/30 30/35 35/40 560 x 560 610 840 40/45/50 45/50/60 35 80 120 200 310 430 14/181) 18/22 22/25 25/30 30/35 35/40 Clamping unit asic hydraulic 2500 kn 3500 kn 4200 kn 45 kw 55 kw 55 kw Injection unit/ Distance Screw between tie bars V++R V++R V++R 630 x 630 840 1450 45/50/60 50/60/70 35 80 120 200 310 430 1) 14/18 18/22 22/25 25/30 30/35 35/40 710 x 630 810 x 710 840 1450 45/50/60 50/60/70 80 120 200 310 430 600 18/22 22/25 25/30 30/35 35/40 40/45 1450 2300 50/60/70 60/70/80 80 120 200 310 430 600 18/22 22/25 25/30 30/35 35/40 40/45 1) only V-variante

Technical parameterseev, EE, and EER-Modul Injection unit 35 80 120 200 Screw diameter [mm] 14 18 18 22 22 25 25 30 /D ratio 20 20 20 20 20 20 20 20 Spec. injection pressure (up to 400 C) [bar] 2755 0 2668 2061 2591 2006 2752 1995 Max. cylinder head volume [cm 3 ] 14 23 23 42 42 61 61 106 Max. shot weight (PS) [g] 12 20 20 37 37 54 54 94 Rate of injection (PS) 54 89 68 101 80 104 72 104 Plasticising rate (PS) motor 1 (120 bar) 2) [g/s] 2 6 6 10 8 13 11 18 motor 2 (120 bar) 2) [g/s] 1 5 5 8 6 11 8 14 Max. screw stroke [mm] 90 90 90 110 110 125 125 150 heating capacity of screw cylinder [ kw] 4.0 5.0 5.0 5.1 5.1 5.7 5.7 8.3 EEV-Modul Max. distance of nozzle retraction [mm] 400 505 505 505 Nozzle sealing force [kn] 30 30 30 30 opper capacity [ltr.] 20 20 20 20 Net weight (without oil) [ kg] 500 550 550 650 EE-Modul Max. distance of nozzle retraction [mm] 550 550 550 Nozzle sealing force [kn] 30 30 30 opper capacity [ltr.] 35 35 35 Net weight (without oil) [ kg] 700 700 750 EER-Modul Max. distance of nozzle retraction [mm] 500 500 500 Nozzle sealing force [kn] 50 50 50 opper capacity [ltr.] 20 20 20 Net weight (without oil) [ kg] 800 800 850 Injection unit 310 430 ET 50-250 430 ET 350/420 600 Screw diameter [mm] 30 35 35 40 35 40 40 45 /D ratio 20 20 20 20 20 20 20 20 Spec. injection pressure (up to 400 C) [bar] 2750 2020 2640 2020 2640 2020 2420 1910 Max. cylinder head volume [cm 3 ] 106 168 168 231 168 231 231 322 Max. shot weight (PS) [g] 94 149 149 205 149 205 205 291 Rate of injection (PS) 76 103 81 106 125 136 136 172 Plasticising rate (PS) motor 1 (120 bar) 2) [g/s] 14 19 19 28 24 35 18 23 motor 2 (120 bar) 2) [g/s] 11 15 15 25 19 28 15 19 Max. screw stroke [mm] 150 175 175 184 175 184 184 203 heating capacity of screw cylinder [ kw] 8.3 9.4 9.4 11.1 9.4 11.1 11.1 11.3 EEV-Modul Max. distance of nozzle retraction [mm] 470 470 470 470 Nozzle sealing force [kn] 30 30 30 30 opper capacity [ltr.] 20 20 20 20 Net weight (without oil) [ kg] 675 700 700 1100 EE-Modul Max. distance of nozzle retraction [mm] 306 400 400 400 Nozzle sealing force [kn] 30 30 30 30 opper capacity [ltr.] 35 35 35 35 Net weight (without oil) [ kg] 950 1000 1000 1250 EER-Modul Max. distance of nozzle retraction [mm] 500 500 500 500 Nozzle sealing force [kn] 50 50 50 50 opper capacity [ltr.] 20 20 20 20 Net weight (without oil) [ kg] 875 900 900 1200

Technical Data Multi 50 Sumitomo (SI) Demag Multi 50 International size description 500/370-120 50/370-120h/35v 50/370-120h/80v 50/370-120h/120v International size description 500/370-200 50/370-200h/35v 50/370-200h/80v 50/370-200h/120v Clamping unit 50/370 Clamping force [kn] 500 ocking force [kn] 500 Max. mould opening stroke [mm] 400 Min. mould height [mm] /310 90/190 1) Max. mould height [mm] - Overall size of platens [mm] 610/710 490/590 1) Mouldplaten(hxv) [mm] 540x530 Distance between tie bars (h x v) [mm] 370x370 Rotary table diameter [mm] 396 Rotary table height [mm] 120 Ejection stroke [mm] 125 Ejection force [kn] 41,2 Retraction force [kn] 14,8 Injection unit 1 120h 200h Screw diameter [mm] 22 25 30 25 30 35 /D ratio 20 20 20 20 20 20 Injection pressure (up to 400 C) [bar] 2510 1940 1350 2740 1900 1400 Cylinder head volume, max. [cm 3 ] 41,8 61,3 88,3 61,3 106 144,2 Max. shot weight (PS) [g] 37 54 78 54 94 128 Rate of injection (PS) 2) > without accumulator [cm 3 /s] 70/82 91/106 131/152 65/75 93/108 127/148 > with accumulator [cm 3 /s] 198 256 370 256 370 503 Plasticising rate (PS) 2) > motor 1 (120 bar) [g/s] 7/9 13/15 18/22 10/15 14/21 23/34 > motor 2 (120 bar) [g/s] 6/9 10/15 14/21 8/11 11/16 18/26 Max. screw stroke [mm] 110 125 125 125 150 150 Max. distance of nozzle retraction [mm] 200 200 Min. nozzle dipping depth (SVO) [mm] 40 40 Nozzle sealing force [kn] 60 60 eating capacity of screw cylinder [kw] 5,1 5,7 8,3 5,7 8,3 9,4 Electric screw drive [kw] 0 - opper capacity [ltr.] 35 35 Injection unit 2 Technical parameters see page 1 and page 32 General data 50/370-120h/... 50/370-200h/... Oil tank capacity [ltr.] 145 145 Pump unit [kw] 18,5 18,5 Total installed electrical rating 3) [kw] 23,6 24,2 26,8 24,2 26,8 27,9 > at electric screw drive [kw] - - - - - - Dry cycles (Euromap 6) 4) [s-mm] 1,80-259 1,80-259 Net weight (without oil) 3) [ kg] 3700 4000 We reserve the right to make changes as a result of further technical advantages 1) with rotary table (mould height adjustable on the machine) 2) parallel operation / mono-operation and serial injection 3) plus the values for the 2nd (and 3rd) injection unit 4) in mono-operation 2

Machine dimensions Multi 50 4058 1333 1755 850 390 715 445 665 78 268 440 1160 630 440 390 844 1700 1642 1840 2035 390 1730 M 500 700 450 3312 3802 840 M Injection unit 35v 2387 3000 Injection unit 80v 2487 3100 Injection unit 120v 2537 3150 3

Technical Data Multi 50 Platen dimensions Multi 50 min. /310 max 610/710 Z 40 105 35 M12x23 Z ole pattern for robot/sprue picker on fixed platen 125 8 125 8 272.5 M16x32 420 10 70 Moving platen - ixed platen - 392 660 268 540 153 M12 32 23 420 370 175 140 105 85 153 530 70 370 420 368 ole pattern according universal k = minimum permissible mould-ø 200 mm Max. permissible mould weight 750 kg, max. 500 kg of it on the moving platen support bearings ore diameter 27 through holes 105 140 175 70 k 50 4

Technical Data Multi 80 Sumitomo (SI) Demag Multi 80 International size description 800/420-120 80/420-120h/35v 80/420-120h/80v 80/420-120h/120v 80/420-120h/200v International size description 800/420-200 80/420-200h/35v 80/420-200h/80v 80/420-200h/120v 80/420-200h/200v International size description 800/420-310 80/420-310h/35v 80/420-310h/80v 80/420-310h/120v 80/420-310h/200v Clamping unit 80/420 Clamping force [kn] 800 ocking force [kn] 800 Max. mould opening stroke [mm] 450 Min. mould height [mm] 250/350 130/230 1) Max. mould height [mm] - Overall size of platens [mm] 700/800 580/680 1) Mouldplaten(hxv) [mm] 590x600 Distance between tie bars (h x v) [mm] 420x420 Rotary table diameter [mm] 462 Rotary table height [mm] 120 Ejection stroke [mm] 150 Ejection force [kn] 41,2 Retraction force [kn] 14,8 Injection unit 1 120h 200h 310h Screw diameter [mm] 25 30 25 30 35 30 35 40 /D ratio 20 20 20 20 20 20 20 20 Injection pressure (up to 400 C) [bar] 1940 1350 2740 1900 1400 2750 2020 1550 Cylinder head volume, max. [cm 3 ] 61,3 88,3 61,3 106 144,2 106 168,3 219,8 Max. shot weight (PS) [g] 54 78 54 94 128 94 149 195 Rate of injection (PS) 2) > without accumulator [cm 3 /s] 106/145 152/209 75/103 108/148 148/201 74/102 102/139 133/182 > with accumulator [cm 3 /s] 256 370 256 370 503 370 503 657 Plasticising rate (PS) 2) > motor 1 (120 bar) [g/s] 15/16 22/23 15/15 21/21 34/34 16/18 26/30 37/41 > motor 2 (120 bar) [g/s] 15/15 21/21 11/13 16/18 26/30 13/14 21/24 29/33 Max. screw stroke [mm] 125 125 125 150 150 150 175 175 Max. distance of nozzle retraction [mm] 200 200 250 Min. nozzle dipping depth (SVO) [mm] 40 40 40 Nozzle sealing force [kn] 60 60 60 eating capacity of screw cylinder [kw] 5,7 8,3 5,7 8,3 9,4 8,3 9,4 11,1 Electric screw drive [kw] - - - opper capacity [ltr.] 35 35 35 Injection unit 2 Technical parameters see page 1 and page 32 General data 80/420-120h/... 80/420-200h/... 80/420-310h/... Oil tank capacity [ltr.] 180 180 180 Pump unit [kw] 22 22 22 Total installed electrical rating 3) [kw] 24,2 26,8 24,2 26,8 27,9 30,3 31,4 33,1 > at electric screw drive [kw] - - - - - - - - Dry cycles (Euromap 6) 4) [s-mm] 1,92-294 1,92-294 1,92-294 Net weight (without oil) 3) [ kg] 4750 4750 4750 We reserve the right to make changes as a result of further technical advantages 1) with rotary table (mould height adjustable on the machine) 2) parallel operation / mono-operation and serial injection 3) plus the values for the 2nd (and 3rd) injection unit 4) in mono-operation 5

Technical Data Multi 80 Machine dimensions Multi 80 2028 965 4310 390 1378 744 476 695 295 78 630 440 390 845 1 1732 1790 1886 2035 M 440 390 1730 610 960 3890 4268 890 510 M Injection unit 35v 2472 3085 Injection unit 80v 2572 3185 Injection unit 120v 2622 3235 Injection unit 200v 2785 3405 6

Platen dimensions Multi 80 min. 250/350 max 700/800 Z 40 Z ole pattern for robot/sprue picker on fixed platen 105 35 M16x28 M16x32 125 8 125 8 490 307.5 M16x32 10 70 Moving platen ixed platen - - 420 690 295 590 175 M16 38 32 600 480 420 85 590 175 245 175 140 105 70 420 480 600 426 ole pattern according universal k = minimum permissible mould-ø 215 mm Max. permissible mould weight 950 kg, max. 650 kg of it on the moving platen support bearings ore diameter 27 through holes 105 140 175 245 70 k 60 7

Technical Data Multi 110 Sumitomo (SI) Demag Multi 110 International size description 1100/470-310 110/470-310h/35v 110/470-310h/80v 110/470-310h/120v 110/470-310h/200v 110/470-310h/310v International size description 1100/470-430 110/470-430h/35v 110/470-430h/80v 110/470-430h/120v 110/470-430h/200v 110/470-430h/310v Clamping unit 110/470 Clamping force [kn] 1100 ocking force [kn] 1100 Max. mould opening stroke [mm] 600 Min. mould height [mm] 250/350 130/230 1) Max. mould height [mm] - Overall size of platens [mm] 850/950 730/830 1) Mouldplaten(hxv) [mm] 670x670 Distance between tie bars (h x v) [mm] 470x470 Rotary table diameter [mm] 562 Rotary table height [mm] 120 Ejection stroke [mm] 180 Ejection force [kn] 41,2 Retraction force [kn] 14,8 Injection unit 1 310h 430h Screw diameter [mm] 30 35 40 35 40 45 /D ratio 20 20 20 20 20 20 Injection pressure (up to 400 C) [bar] 2750 2020 1550 2640 2020 1600 Cylinder head volume, max. [cm 3 ] 106 168,3 219,8 168,3 231,2 292,6 Max. shot weight (PS) [g] 94 149 195 149 205 259 Rate of injection (PS) 2) > without accumulator [cm 3 /s] 130/161 176/219 230/287 135/168 176/219 223/278 > with accumulator [cm 3 /s] 370 503 657 503 657 830 Plasticising rate (PS) 2) > motor 1 (120 bar) [g/s] 21/21 35/35 48/48 28/32 39/45 52/60 > motor 2 (120 bar) [g/s] 17/20 28/32 39/45 22/25 31/35 42/47 Max. screw stroke [mm] 150 175 175 175 184 184 Max. distance of nozzle retraction [mm] 250 300 Min. nozzle dipping depth (SVO) [mm] 40 40 Nozzle sealing force [kn] 60 60 eating capacity of screw cylinder [kw] 8,3 9,4 11,1 9,4 11,1 11,3 Electric screw drive [kw] - - opper capacity [ltr.] 35 35 Injection unit 2 Technical parameters see page 1 and page 32 General data 110/470-310h/... 110/470-430h/... Oil tank capacity [ltr.] 220 220 Pump unit [kw] 30 30 Total installed electrical rating 3) [kw] 38,3 39,4 41,1 39,4 41,1 41,3 > at electric screw drive [kw] - - - - - - Dry cycles (Euromap 6) 4) [s-mm] 2,20-329 2,20-329 Net weight (without oil) 3) [ kg] 6350 6350 We reserve the right to make changes as a result of further technical advantages 1) with rotary table (mould height adjustable on the machine) 2) parallel operation / mono-operation and serial injection 3) plus the values for the 2nd (and 3rd) injection unit 4) in mono-operation 8

Machine dimensions Multi 110 2431 1127 4831 390 1445 786 532 727 344 78 630 440 390 865 1260 1963 1902 1937 2035 M 440 390 1730 630 1110 4191 4781 980 590 M Injection unit 35v 2557 3170 Injection unit 80v 2657 3270 Injection unit 120v 2707 3320 Injection unit 200v 2880 3500 Injection unit 310v 2995 3695 9

Technical Data Multi 110 Platen dimensions Multi 110 min. 250/350 max 850/950 Z 40 105 35 Z ole pattern for robot/sprue picker on fixed platen M16x28 M16x32 125 8 125 8 342.5 M16x32 490 10 70 Moving platen - ixed platen - 476 727 344 38 670 195 M16 32 540 470 245 175 140 85 120 195 670 70 470 540 487 ole pattern according universal k = minimum permissible mould-ø 230 mm Max. permissible mould weight 1500 kg, max. 1000 kg of it on the moving platen support bearings ore diameter 27 through holes 175 245 140 70 k ø 70 10

Technical Data Multi 125 Sumitomo (SI) Demag Multi 125 International size description 1250/475-320 125/475-320h/35v 125/475-320h/80v 125/475-320h/120v 125/475-320h/200v 125/475-320h/310v 125/475-320h/430v International size description 1250/475-440 125/475-440h/35v 125/475-440h/80v 125/475-440h/120v 125/475-440h/200v 125/475-440h/310v 125/475-440h/430v Demag Plastics Group Multi 125 International size description 1250/475-320 125/475-320h/80l 125/475-320h/120l 125/475-320h/200l 125/475-320h/310l 125/475-320h/430l International size description 1250/475-440 125/475-440h/80l 125/475-440h/120l 125/475-440h/200l 125/475-440h/310l 125/475-440h/430l Clamping unit 125/475 Clamping force [kn] 1250 ocking force [kn] 1375 Max. mould opening stroke [mm] 450 Min. mould height [mm] 230/130 1) Max. mould height [mm] 560/460 1) Overall size of platens [mm] 1010/910 1) Mouldplaten(hxv) [mm] 690x660 Distance between tie bars (h x v) [mm] 475x450 Rotary table diameter [mm] 620 Rotary table height [mm] 100 Ejection stroke [mm] 140/65 1) Ejection force [kn] 59/59 Retraction force [kn] 29 Injection unit 1 320h 440h Screw diameter [mm] 30 35 40 35 40 45 /D ratio 20 20 20 20 20 20 Injection pressure (up to 400 C) [bar] 2420 1877 1437 2423 1855 1466 Cylinder head volume, max. [cm 3 ] 124 168 220 177 231 293 Max. shot weight (PS) [g] 110 150 200 160 260 Rate of injection (PS) 2) > without accumulator [cm 3 /s] 120/170 160/230 /300 120/180 160/230 /290 > with accumulator [cm 3 /s] 460 595 735 595 735 880 Plasticising rate (PS) 2) > motor 1 (120 bar) [g/s] 20/29 28/39 41/58 22/31 32/46 41/58 > motor 2 (120 bar) [g/s] 16/23 22/31 32/46 17/24 24/35 31/44 Max. screw stroke [mm] 175 184 Max. distance of nozzle retraction [mm] 350 350 Min. nozzle dipping depth (SVO) [mm] 20 20 Nozzle sealing force [kn] 80 80 eating capacity of screw cylinder [kw] 7,9 8,3 11,7 8,3 11,7 13 Electric screw drive [kw] 12,6 12,6 opper capacity [ltr.] 70 70 Injection unit 2 Technical parameters see page 1 and page 32 General data 125/475-320h/... 125/475-440h/... Oil tank capacity [ltr.] 400 400 Pump unit [kw] 30 30 Total installed electrical rating 3) [kw] 37,9 38,3 41,7 38,3 41,7 43 > at electric screw drive [kw] 50,5 50,9 54,3 50,9 54,3 55,6 Dry cycles (Euromap 6) 4) [s-mm] 1,85-332 1,85-332 Net weight (without oil) 3) [ kg] 6300 6600 We reserve the right to make changes as a result of further technical advantages 1) with rotary table 2) parallel operation / mono-operation and serial injection 3) plus the values for the 2nd (and 3rd) injection unit 4) in mono-operation 11

Technical Data Multi 125 Machine dimensions Multi 125 V-version Tie ar Removal 2240 330 2340 1100 985 85 1635 800 665 1500 600 345 950 450 2000 1295 2077 K 275 M 440 630 800 4200 520 730 425 4910 460 K M Injection unit 320h 218 2042 Injection unit 440h 436 2057 Injection unit 35v 2632 3245 Injection unit 80v 2732 3345 Injection unit 120v 2782 3395 Injection unit 200v 2945 3565 Injection unit 310v 3060 3760 Injection unit 430v 3185 3885 Machine dimensions Multi 125 -version Tie ar Removal 1500 2240 330 2340 1100 985 800 665 85 1295 600 2000 950 K 2070 1880 775 450 2077 275 710 630 345 800 4200 4910 990 520 730 425 460 K Injection unit 320h 218 2042 Injection unit 440h 436 2057 Injection unit 80l 2286 Injection unit 120l 2286 Injection unit 200l 2286 Injection unit 310l 2825 Injection unit 430l 2825 1120 12

Platen dimensions Multi 125 100 450 min. 230 max. 560 Z 20 10 105 35 Z ole pattern for robot/sprue picker on fixed platen 27 125 8 125 8 330 175 M16 x 32 12 Moving platen - ixed platen - 621 766 M16 690 203.2 88.9 50.8 40 540 475 88,9 50,8 660 139,7 245 175 140 70 450 515 670 470 ole pattern according Euromap k = minimum permissible mould-ø 285 mm Max. permissible mould weight 1400kg, 1160kg with rotary table max. 1000 kg of it on the moving platen support bearings, 760kg with rotary table ore diameter 27 through holes 140 175 245 70 65 k 13

Technical Data Multi 150 Sumitomo (SI) Demag Multi 150 International size description 1500/500-440 150/500-440h/35v 150/500-440h/80v 150/500-440h/120v 150/500-440h/200v 150/500-440h/310v 150/500-440h/430v International size description 1500/500-610 150/500-610h/35v 150/500-610h/80v 150/500-610h/120v 150/500-610h/200v 150/500-610h/310v 150/500-610h/430v Demag Plastics Group Multi 150 International size description 1500/500-440 150/500-440h/80l 150/500-440h/120l 150/500-440h/200l 150/500-440h/310l 150/500-440h/430l International size description 1500/500-610 150/500-610h/80l 150/500-610h/120l 150/500-610h/200l 150/500-610h/310l 150/500-610h/430l Demag Plastics Group Multi 150 International size description 1500/500-440 150/500-440h/80r 150/500-440h/120r 150/500-440h/200r 150/500-440h/310r 150/500-440h/430r International size description 1500/500-610 150/500-610h/80r 150/500-610h/120r 150/500-610h/200r 150/500-610h/310r 150/500-610h/430r Clamping unit 150/500 Clamping force [kn] 1500 ocking force [kn] 1650 Max. mould opening stroke [mm] 500 Min. mould height [mm] 250/150 1) Max. mould height [mm] 660/560 1) Overall size of platens [mm] 1160/1060 1) Mouldplaten(hxv) [mm] 750x750 Distance between tie bars (h x v) [mm] 500x500 Rotary table diameter [mm] 670 Rotary table height [mm] 100 Ejection stroke [mm] 160/95 1) Ejection force [kn] 59 Retraction force [kn] 26 Injection unit 1 440h 610h Screw diameter [mm] 35 40 45 40 45 50 /D ratio 20 20 20 20 20 20 Injection pressure (up to 400 C) [bar] 2423 1855 1466 2418 1973 1598 Cylinder head volume, max. [cm 3 ] 177 231 293 255 323 399 Max. shot weight (PS) [g] 160 260 230 290 360 Rate of injection (PS) 2) > without accumulator [cm 3 /s] 120/180 160/230 /290 120/170 150/220 190/270 > with accumulator [cm 3 /s] 595 735 880 735 880 1020 Plasticising rate (PS) 2) > motor 1 (120 bar) [g/s] 22/31 32/46 41/58 24/35 31/44 44/62 > motor 2 (120 bar) [g/s] 17/24 24/35 31/44 16/23 21/29 29/42 Max. screw stroke [mm] 184 203 Max. distance of nozzle retraction [mm] 350 350 Min. nozzle dipping depth (SVO) [mm] 20 20 Nozzle sealing force [kn] 80 80 eating capacity of screw cylinder [kw] 8,3 11,7 13 11,7 13 14,8 Electric screw drive [kw] 12,6 12,6 opper capacity [ltr.] 70 70 Injection unit 2 Technical parameters see page 1 and page 32 General data 150/500-440h/... 150/500-610h/... Oil tank capacity [ltr.] 400 400 Pump unit [kw] 30 30 Total installed electrical rating 3) [kw] 38,3 41,7 43 41,7 43 44,8 > at electric screw drive [kw] 50,9 54,3 55,6 60,3 61,6 63,4 Dry cycles (Euromap 6) 4) [s-mm] 2,15-350 2,15-350 Net weight (without oil) 3) [ kg] 7500 7500 We reserve the right to make changes as a result of further technical advantages 1) with rotary table 2) parallel operation / mono-operation and serial injection 3) plus the values for the 2nd (and 3rd) injection unit 4) in mono-operation 14

Machine dimensions Multi 150 V-version Tie ar Removal 2520 330 2340 1240 985 85 1680 820 690 1500 450 2000 1320 555 320 950 2077 K M 440 275 810 900 570 4480 750 450 5190 485 K M Injection unit 440h 436 2082 Injection unit 610h 661 2082 Injection unit 35v 2702 3315 Injection unit 80v 2 3415 Injection unit 120v 2852 3465 Injection unit 200v 3015 3635 Injection unit 310v 3130 3830 Injection unit 430v 3255 3955 Machine dimensions Multi 150 -version Tie ar Removal 1500 2520 330 2340 1240 985 820 690 85 2000 1320 555 950 K 800 2095 1905 450 2077 275 710 840 320 900 4480 5190 970 570 750 450 485 K Injection unit 440h 436 2082 Injection unit 610h 661 2082 Injection unit 80l 2276 Injection unit 120l 2276 Injection unit 200l 2276 Injection unit 310l 2825 Injection unit 410l 2825 1120 15

Technical Data Multi 150 Platen dimensions Multi 150 100 500 min. 250 max. 660 Z 20 105 35 Z ole pattern for robot/sprue picker on fixed platen 27 160 8 160 8 375 175 M16 x 32 15 Moving platen - ixed platen - 656 786 750 M16 570 500 139.7 32 750 50.8 350 70 140 500 570 70 70 50.8 140 510 203.2 350 k ole pattern according Euromap k = minimum permissible mould-ø 300 mm Max. permissible mould weight 2050 kg, 1770kg with rotary table max. 1500 kg of it on the moving platen support bearings, 1220kg with rotary table ore diameter 27 through holes 16

Technical Data Multi 200 Sumitomo (SI) Demag Multi 200 International size description 2000/560-610 200/560-610h/35v 200/560-610h/80v 200/560-610h/120v 200/560-610h/200v 200/560-610h/310v 200/560-610h/430v International size description 2000/560-840 200/560-840h/35v 200/560-840h/80v 200/560-840h/120v 200/560-840h/200v 200/560-840h/310v 200/560-840h/430v Demag Plastics Group Multi 200 International size description 2000/560-610 200/560-610h/80l 200/560-610h/120l 200/560-610h/200l 200/560-610h/310l 200/560-610h/430l International size description 2000/560-840 200/560-840h/80l 200/560-840h/120l 200/560-840h/200l 200/560-840h/310l 200/560-840h/430l Demag Plastics Group Multi 200 International size description 2000/560-610 200/560-610h/80r 200/560-610h/120r 200/560-610h/200r 200/560-610h/310r 200/560-610h/430r International size description 2000/560-840 200/560-840h/80r 200/560-840h/120r 200/560-840h/200r 200/560-840h/310r 200/560-840h/430r Clamping unit 200/560 Clamping force [kn] 2000 ocking force [kn] 2200 Max. mould opening stroke [mm] 575 Min. mould height [mm] 310/200 1) Max. mould height [mm] 760/650 1) Overall size of platens [mm] 1335/1225 1) Mouldplaten(hxv) [mm] 830x830 Distance between tie bars (h x v) [mm] 560x560 Rotary table diameter [mm] 760 Rotary table height [mm] 110 Ejection stroke [mm] 180/160 1) Ejection force [kn] 69 Retraction force [kn] 31 Injection unit 1 610h 840h Screw diameter [mm] 40 45 50 45 50 60 /D ratio 20 20 20 20 20 20 Injection pressure (up to 400 C) [bar] 2418 1973 1598 2402 1946 1351 Cylinder head volume, max. [cm 3 ] 255 323 399 358 442 636 Max. shot weight (PS) [g] 230 290 360 320 400 570 Rate of injection (PS) 2) > without accumulator [cm 3 /s] 170/200 220/250 270/310 180/ 220/250 320/370 > with accumulator [cm 3 /s] 735 880 1020 880 1020 1 Plasticising rate (PS) 2 > motor 1 (120 bar) [g/s] 35/40 44/50 62/72 29/33 41/48 64/74 > motor 2 (120 bar) [g/s] 23/27 29/34 42/48 21/24 29/34 46/53 Max. screw stroke [mm] 203 225 Max. distance of nozzle retraction [mm] 400 400 Min. nozzle dipping depth (SVO) [mm] 20 20 Nozzle sealing force [kn] 80 80 eating capacity of screw cylinder [kw] 11,7 13 14,8 13 14,8 23,1 Electric screw drive [kw] 18,6 20,5 opper capacity [ltr.] 70 70 Injection unit 2 Technical parameters see page 1 and page 32 General data 200/560-610h/... 200/560-840h/... Oil tank capacity [ltr.] 500 500 Pump unit [kw] 37 37 Total installed electrical rating 3) [kw] 48,7 50 51,8 50 51,8 60,1 > at electric screw drive [kw] 67,3 68,8 66,6 70,5 72,3 80,6 Dry cycles (Euromap 6) 4) [s-mm] 2,20-392 2,20-392 Net weight (without oil) 3) [ kg] 9800 10100 We reserve the right to make changes as a result of further technical advantages 1) with rotary table 2) parallel operation / mono-operation and serial injection 3) plus the values for the 2nd (and 3rd) injection unit 4) in mono-operation 17

Technical Data Multi 200 Machine dimensions Multi 200 V-version Tie ar Removal 1500 2845 330 2540 1390 985 85 1880 970 740 2000 1350 555 310 950 K 275 2077 M 440 960 1000 4930 5715 450 670 800 495 530 K M Injection unit 610h 511 2112 Injection unit 840h 880 2122 Injection unit 35v 2772 3385 Injection unit 80v 2872 3485 Injection unit 120v 3035 3535 Injection unit 200v 3150 3705 Injection unit 310v 3265 3900 Injection unit 430v 3390 4025 Machine dimensions Multi 200 -version Tie ar Removal 1500 2845 330 2540 1390 985 970 740 85 2000 555 1350 950 K 830 2125 1935 450 2077 275 785 960 310 1000 4930 5715 570 800 495 485 K Injection unit 610h 511 2112 Injection unit 840h 880 2122 Injection unit 80l 2296 Injection unit 120l 2296 Injection unit 200l 2296 Injection unit 310l 2855 Injection unit 430l 2855 1120 18

Platen dimensions Multi 200 175 Z ole pattern for robot/sprue picker on fixed platen 100 575 min. 310 max. 760 20 Z 35 27 160 8 160 8 415 350 M20 x 40 15 Moving platen - ixed platen - 706 936 830 M20 640 560 40 830 203.2 350 140 560 640 50.8 70 50.8 70 203.2 140 80 600 ole pattern according Euromap k = minimum permissible mould-ø 350 mm Max. permissible mould weight 2500 kg, 2110kg with rotary table max. 1700 kg of it on the moving platen support bearings, 1310 kg with rotary table ore diameter 27 through holes 350 k 19

Technical Data Multi 250 Sumitomo (SI) Demag Multi 250 International size description 2500/630-840 250/630-840h/35v 250/630-840h/80v 250/630-840h/120v 250/630-840h/200v 250/630-840h/310v 250/630-840h/430v International size description 2500/630-1450 250/630-1450h/35v 250/630-1450h/80v 250/630-1450h/120v 250/630-1450h/200v 250/630-1450h/310v 250/630-1450h/430v Demag Plastics Group Multi 250 International size description 2500/630-840 250/630-840h/80l 250/630-840h/120l 250/630-840h/200l 250/630-840h/310l 250/630-840h/430l International size description 2500/630-1450 250/630-1450h/80l 250/630-1450h/120l 250/630-1450h/200l 250/630-1450h/310l 250/630-1450h/430l Demag Plastics Group Multi 250 International size description 2500/630-840 250/630-840h/80r 250/630-840h/120r 250/630-840h/200r 250/630-840h/310r 250/630-840h/430r International size description 2500/630-1450 250/630-1450h/80r 250/630-1450h/120r 250/630-1450h/20r 250/630-1450h/310r 250/630-1450h/430r Clamping unit 250/630 Clamping force [kn] 2500 ocking force [kn] 2750 Max. mould opening stroke [mm] 675 Min. mould height [mm] 310/200 1) Max. mould height [mm] 830/720 1) Overall size of platens [mm] 1505/1395 1) Mouldplaten(hxv) [mm] 950x950 Distance between tie bars (h x v) [mm] 630x630 Rotary table diameter [mm] 870 Rotary table height [mm] 110 Ejection stroke [mm] 200/160 1) Ejection force [kn] 80 Retraction force [kn] 35 Injection unit 1 840h 1450h Screw diameter [mm] 45 50 60 50 60 70 /D ratio 20 20 20 20 20 20 Injection pressure (up to 400 C) [bar] 2402 1946 1351 2426 1905 1400 Cylinder head volume, max. [cm 3 ] 358 442 636 530 763 1039 Max. shot weight (PS) [g] 320 400 570 480 690 940 Rate of injection (PS) 2) > without accumulator [cm 3 /s] /260 250/320 370/460 180/230 260/330 350/440 > with accumulator [cm 3 /s] 880 1020 1 1020 1 1500 Plasticising rate (PS) 2) > motor 1 (120 bar) [g/s] 33/42 48/60 74/93 34/42 53/66 75/94 > motor 2 (120 bar) [g/s] 24/30 34/42 53/66 21/27 33/41 47/59 Max. screw stroke [mm] 225 270 Max. distance of nozzle retraction [mm] 440 440 Min. nozzle dipping depth (SVO) [mm] 20 20 Nozzle sealing force [kn] 80 110 eating capacity of screw cylinder [kw] 13 14,8 23,1 14,8 23,1 27 Electric screw drive [kw] 20,5 20,5 opper capacity [ltr.] 70 110 Injection unit 2 Technical parameters see page 1 and page 32 General data 250/630-840h/... 250/630-1450h/... Oil tank capacity [ltr.] 700 700 Pump unit [kw] 45 45 Total installed electrical rating 3) [kw] 58 59,8 68,1 59,8 68,1 72 > at electric screw drive [kw] 78,5 80,3 88,6 89,8 98,1 110,6 Dry cycles (Euromap 6) 4) [s-mm] 2,30-441 2,30-441 Net weight (without oil) 3) [ kg] 12600 13100 We reserve the right to make changes as a result of further technical advantages 20 1) with rotary table 2) parallel operation / mono-operation and serial injection 3) plus the values for the 2nd (and 3rd) injection unit 4) in mono-operation

Machine dimensions Multi 250 V-version Tie ar Removal 3230 330 2910 1625 985 85 2040 1050 820 1800 1385 520 300 950 450 2097 2000 K 2232 275 2077 M 440 1040 1200 5580 6470 780 880 580 615 K M Injection unit 840h 550 2157 Injection unit 1450h 1073 2292 Injection unit 35v 2867 3480 Injection unit 80v 2967 3580 Injection unit 120v 3017 3630 Injection unit 200v 3180 3800 Injection unit 310v 3295 3995 Injection unit 430v 3420 4120 Machine dimensions Multi 250 -version Tie ar Removal 1800 3230 330 2910 1625 985 1050 820 85 1385 2097 2000 520 950 2232 K 865 2160 1970 450 2077 300 275 890 1040 1200 5580 6470 910 780 880 580 615 K Injection unit 840h 550 2157 Injection unit 1450h 1073 2292 Injection unit 80l 2315 Injection unit 120l 2315 Injection unit 200l 2315 Injection unit 310l 2895 Injection unit 430 2895 1120 21

Technical Data Multi 250 Platen dimensions Multi 250 Z ole pattern for robot/sprue picker on fixed platen 175 125 675 min. 330 max. 830 20 Z 35 27 160 8 160 8 475 420 M20 X 40 15 Moving platen - ixed platen - 766 996 950 M20 720 630 50.8 203.2 40 630 720 950 140 50.8 420 350 203.2 690 350 420 140 k 90 ole pattern according Euromap k = minimum permissible mould-ø 400 mm Max. permissible mould weight 3300 kg, 2790kg with rotary table max. 2200 kg of it on the moving platen support bearings, 1690kg with rotary table ore diameter 27 through holes 22

Technical Data Multi 350 Sumitomo (SI) Demag Multi 350 International size description 3500/710-840 350/710-840h/80v 350/710-840h/120v 350/710-840h/200v 350/710-840h/310v 350/710-840h/430v 350/710-840h/600v International size description 3500/710-1450 350/710-1450h/80v 350/710-1450h/120v 350/710-1450h/200v 350/710-1450h/310v 350/710-1450h/430v 350/710-1450h/600v Demag Plastics Group Multi 350 International size description 3500/710-840 350/710-840h/80l 350/710-840h/120l 350/710-840h/200l 350/710-840h/310l 350/710-840h/430l 350/710-840h/600l International size description 3500/710-1450 350/710-1450h/80l 350/710-1450h/120l 350/710-1450h/200l 350/710-1450h/310l 350/710-1450h/430l 350/710-1450h/600l Demag Plastics Group Multi 350 International size description 3500/710-840 350/710-840h/80r 350/710-840h/120r 350/710-840h/200r 350/710-840h/310r 350/710-840h/430r 350/710-840h/600r International size description 3500/710-1450 350/710-1450h/80r 350/710-1450h/120r 350/710-1450h/200r 350/710-1450h/310r 350/710-1450h/430r 350/710-1450h/600r Clamping unit 350/710 Clamping force [kn] 3500 ocking force [kn] 3850 Max. mould opening stroke [mm] 675 Min. mould height [mm] 330/220 1) Max. mould height [mm] 830/720 1) Overall size of platens [mm] 1505/1395 1) Mouldplaten(hxv) [mm] 1040x950 Distance between tie bars (h x v) [mm] 710x630 Rotary table diameter [mm] 920 Rotary table height [mm] 110 Ejection stroke [mm] 200/160 1) Ejection force [kn] 69 Retraction force [kn] 31 Injection unit 1 840h 1450h Screw diameter [mm] 45 50 60 50 60 70 /D ratio 20 20 20 20 20 20 Injection pressure (up to 400 C) [bar] 2402 1946 1351 2426 1905 1400 Cylinder head volume, max. [cm 3 ] 358 442 636 530 763 1039 Max. shot weight (PS) [g] 320 400 570 480 690 940 Rate of injection (PS) 2) > without accumulator [cm 3 /s] 260/300 320/380 460/540 230/270 330/380 440/520 > with accumulator [cm 3 /s] 880 1020 1 1020 1 1500 Plasticising rate (PS) 2) > motor 1 (120 bar) [g/s] 42/49 60/71 93/110 42/50 66/78 94/111 > motor 2 (120 bar) [g/s] 30/35 42/50 66/78 27/31 41/49 59/70 Max. screw stroke [mm] 225 270 Max. distance of nozzle retraction [mm] 470 470 Min. nozzle dipping depth (SVO) [mm] 20 20 Nozzle sealing force [kn] 80 110 eating capacity of screw cylinder [kw] 13 14,8 23,1 14,8 23,1 27 Electric screw drive [kw] 20,5 30 opper capacity [ltr.] 70 110 Injection unit 2 Technical parameters see page 1 and page 32 General data 350/710-840h/... 350/710-1450h/... Oil tank capacity [ltr.] 700 700 Pump unit [kw] 55 55 Total installed electrical rating 3) [kw] 68 69,8 78,1 69,8 78 82 > at electric screw drive [kw] 88,5 100,8 101,2 99,8 108 112 Dry cycles (Euromap 6) 4) [s-mm] 2,80-497 2,80-497 Net weight (without oil) 3) [ kg] 14800 15300 We reserve the right to make changes as a result of further technical advantages 1) with rotary table 2) parallel operation / mono-operation and serial injection 3) plus the values for the 2nd (and 3rd) injection unit 4) in mono-operation 23

Technical Data Multi 350 Machine dimensions Multi 350 V-version Tie ar Removal 3230 330 2910 1625 985 85 2125 1135 820 1800 275 1405 520 2135 2000 300 950 2232 K 450 2077 M 440 1370 1200 6470 5910 965 780 580 615 K M Injection unit 840h 580 2177 Injection unit 1450h 1103 2312 Injection unit 80v 2987 3600 Injection unit 120v 3037 3650 Injection unit 200v 3200 3820 Injection unit 310v 3315 4015 Injection unit 430v 3440 4140 Injection unit 600v 3640 4340 Machine dimensions Multi 350 -version Tie ar Removal 1800 3230 330 2910 1625 985 1135 820 85 2135 2000 1405 520 950 2232 K 885 2180 1990 450 275 2077 560 1370 300 1200 5910 6470 780 965 580 615 K Injection unit 840h 580 2177 Injection unit 1450h 1103 2312 Injection unit 80l 2481 Injection unit 120l 2481 1120 Injection unit 200l 2481 Injection unit 310l 3000 Injection unit 430l 3000 Injection unit 600l 3400 24

Platen dimensions Multi 350 125 675 min. 330 max. 830 Z 20 175 35 Z ole pattern for robot/sprue picker on fixed platen 27 160 8 160 8 475 490 350 M20 X 40 15 Moving platen - ixed platen - 780 1095 1040 M20-815 710 40 420 350 950 630 735 50.8 203.2 140 50.8 203.2 690 350 420 490 140 k 105 ole pattern according Euromap k = minimum permissible mould-ø 400 mm Max. permissible mould weight 3600 kg, 3030 kg with rotary table max. 2400 kg of it on the moving platen support bearings, 1830 kg with rotary table ore diameter 27 through holes 25

Technical Data Multi 420 Sumitomo (SI) Demag Multi 420 International size description 4200/810-1450 420/810-1450h/80v 420/810-1450h/120v 420/810-1450h/200v 420/810-1450h/310v 420/810-1450h/430v 420/810-1450h/600v International size description 4200/810-2300 /810-2300h/80v 420/810-2300h/120v 420/810-2300h/200v 420/810-2300h/310v 420/810-2300h/430v 420/810-2300h/600v Demag Plastics Group Multi 420 International size description 4200/810-1450 420/810-1450h/80l 420/810-1450h/120l 3420/810-1450h/200l 420/810-1450h/310l 420/810-1450h/430l 420/810-1450h/600l International size description 4200/810-2300 420/810-2300h/80l 420/810-2300h/120l 420/810-2300h/200l 420/810-2300h/310l 420/810-2300h/430l 420/810-2300h/600l Demag Plastics Group Multi 420 International size description 4200/810-1450 420/810-1450h/80r 420/810-1450h/120r 420/810-1450h/200r 420/810-1450h/310r 420/810-1450h/430r 420/810-1450h/600r International size description 4200/810-2300 420/810-2300h/80r 420/810-2300h/120r 420/810-2300h/200r 420/810-2300h/310r 420/810-2300h/430r 420/810-2300h/600r Clamping unit 420/810 Clamping force [kn] 4200 ocking force [kn] 4620 Max. mould opening stroke [mm] 710 Min. mould height [mm] 380/260 1) Max. mould height [mm] 940/820 1) Overall size of platens [mm] 1650/1530 1) Mouldplaten(hxv) [mm] 1200x1100 Distance between tie bars (h x v) [mm] 810x710 Rotary table diameter [mm] 1070 Rotary table height [mm] 120 Ejection stroke [mm] 230/165 1) Ejection force [kn] 96 Retraction force [kn] 41 Injection unit 1 1450h 2300h Screw diameter [mm] 50 60 70 60 70 80 /D ratio 20 20 20 20 20 20 Injection pressure (up to 400 C) [bar] 2426 1905 1400 2420 1877 1437 Cylinder head volume, max. [cm 3 ] 530 763 1039 891 1212 1583 Max. shot weight (PS) [g] 480 690 940 800 1090 1430 Rate of injection (PS) 2) > without accumulator [cm 3 /s] 270/270 330/380 440/520 240/290 330/390 430/510 > with accumulator [cm 3 /s] 1020 1 1500 1 1500 1600 Plasticising rate (PS) 2) > motor 1 (120 bar) [g/s] 42/50 66/78 94/111 41/49 59/70 83/98 > motor 2 (120 bar) [g/s] 27/31 41/49 59/70 29/34 42/49 58/69 Max. screw stroke [mm] 270 315 Max. distance of nozzle retraction [mm] 620 620 Min. nozzle dipping depth (SVO) [mm] 20 20 Nozzle sealing force [kn] 110 110 eating capacity of screw cylinder [kw] 15 23 27 23 27 31 Electric screw drive [kw] 30 36 opper capacity [ltr.] 110 110 Injection unit 2 Technical parameters see page 1 and page 32 General data 420/810-1450h/... 420/810-2300h/... Oil tank capacity [ltr.] 730 730 Pump unit [kw] 55 55 Total installed electrical rating 3) [kw] 70 78 82 78 82 86 > at electric screw drive [kw] 100 108 112 114 118 122 Dry cycles (Euromap 6) 4) [s-mm] 2,7-560 2,7-560 Net weight (without oil) 3) [ kg] 19700 20000 We reserve the right to make changes as a result of further technical advantages 26 1) with rotary table 2) parallel operation / mono-operation and serial injection 3) plus the values for the 2nd (and 3rd) injection unit 4) in mono-operation

Machine dimensions Multi 420 V-version Tie ar Removal 3725 330 3685 1870 985 85 2380 1070 940 1800 1530 520 2315 2000 275 370 950 2322 K 450 2077 M 440 1740 1200 7740 7095 940 1050 700 735 K M Injection unit 1450h 478 2437 Injection unit 2300h 916 2467 Injection unit 80v 3187 3800 Injection unit 120v 3237 3850 Injection unit 200v 3400 4020 Injection unit 310v 3515 4215 Injection unit 430v 3640 4140 Injection unit 600v 3840 4340 Machine dimensions Multi 420 -version Tie ar Removal 1800 3725 330 3685 1625 985 1070 940 85 2315 2000 1530 520 560 1740 300 1200 7095 7740 950 2232 K 2305 2000 1010 925 940 1050 700 735 450 275 2077 K Injection unit 1450h 478 2437 Injection unit 2300h 916 2467 1120 Injection unit 80l 2580 Injection unit 120l 2580 Injection unit 200l 2580 Injection unit 310l 3080 Injection unit 430l 3080 Injection unit 600l 3480 27

Technical Data Multi 420 Platen dimensions Multi 420 175 125 710 min. 380 max. 940 Z 20 35 Z ole pattern for robot/sprue picker on fixed platen 27 160 8 160 8 550 490 350 M20 X 40 15 Moving platen - ixed platen - 900 1230 1200 M20 40 930 810 490 420 350 1100 710 830 50.8 203.2 140 50.8 850 203.2 350 420 490 560 140 k 120 ole pattern according Euromap k = minimum permissible mould-ø 420 mm Max. permissible mould weight 5100 kg, 4500 kg with rotary table max. 3400 kg of it on the moving platen support bearings, 0 kg with rotary table ore diameter 27 through holes 28

Equipment Multi 50... 420 Clamping unit > Compact units with fully hydraulic clamping system with two clamp cylinders and a volume multiplier for fast machine cycles and low energy consumption (up to 1.100kN) > Compact 5-point twin toggle with two internal clamping cylinders (from1.250kn) Clamping unit > Pilot operated non return valve combination for moulds with sprung ejector > Stroke measuring system (ultrasonic) via CN-us for injection operation and movement of the injection unit, clamp- and ejector movement and flowmultiplier > Moving platen supported by roller bearings on machine base > Clamp force adjustable at Ergocontrol panel, including indication of actual value > Clamp force control with indication (from 1.250kN) > Mould platen layout universal (Euromap and DIN; up to 1.100kN) > Mould mounting dimensions similar to Euromap (from 1.250kN) > Mould mounting dimensions in accordance to Euromap, with side ejector platen (from 1.250kN) > Mould mounting dimensions similar to DIN (from1.250kn) > Mould mounting dimensions similar to SPI > dd-on rotary table (up to 1.500 kn) > Machine-integrated rotary table, 180º left/right rotation (from 1.250 kn) > utomatic central oil lubrication for toggle (up to 1.250kN) > Upper tiebar on non-operator side retractable > Manual clamping mechanism for tiebar retraction (from 1.250kN) > utomatic tiebar retraction (from 1.250kN) > Two-stage adjustable clamp force (up to 1.100 kn) > utomatic mould height adjustment (from 1.250kN) > ydraulic central ejector with jolt stroke feature and mechanical quick coupling > Chute for small parts (up to 1.100kN) > Short/long stroke ejector > Programmable ejector stroke, pressure and speed > Programmable pressure and speed of ejector simultaneous with mould movement (ejector via on-off valve) > Speed and pressure of ejector programmable simultaneous to mould movement > Programmable pressure and speed of ejector simultaneous with mould movement, with positional control (ejector via on-off valve) > Mould and ejector movements only when safety gate closed (up to 1.100 kn) > Increased mould closing speed with hydraulic differential circuit (mould movement and ejector foreward, with closed safety door only; from 1.250 kn) > Sequence matrix for free programming of ejectors and core pullers (simultaneous to mould movement) > Core puller with 1, 2 or 4 circuits and sequence matrix for independent (serial operation) programming of speed control > Core puller with 2 or 4 circuits and sequence matrix for independent (parallel operation) programming of speed control (from 1.250 kn) > dditional ports for 2 core pullers on fixed mould platen (from 1.250 kn) > xial movement of the indexing plate or centring of a non-demag rotary table via on-off valve (from 1.250 kn) > Rotating function, mould integrated with end switch monitoring > Manual pressure relief for 1, 2 or 4 core pullers > 1 or 2 pneumatic 5/2 directional valves, mounted to moving platen and freely programmable > 1 or 2 pneumatic 5/2 directional valves, mounted to fixed platen and freely programmable > 4-way cooling water volume controller (10l/min) > 4 additional cooling water volume controllers (10l/min) > 8 additional cooling water volume controllers (10l/min) > Time-programmable switch-off of mould cooling > low-through feature for mould cooling lines > utomatic safety gate on operator side > Safety gate prepared for handling device Injection unit > Vertical injection unit (V-version) or > orizontal injection unit (-version, from 1.250 kn) or > R-version injection unit (piggy-back arrangement, from 1.500 kn) or > P-version injection unit (parallel arrangement from 1.250 kn) > Preparation for subsequent replacement of the second injection unit by another Demag Multi modular IU size > Easy access to the mould space by moving the vertical injection unit back over the fixed platen towards the horizontal injection unit > Wear and corrosion resistant universal thermoplastic screw, nitrided cylinder asic equipment dditional price We reserve the right to make changes as a result of further technical advances 29

Equipment Multi 50... 420 Injection unit > Special screws for processing various materials, also available with homogenisation and mixing section, with screws and non-return valves in wear and corrosion resistant or heavy duty design (powder metal) > Open nozzle with M 24x1,5 connection thread, from 18 mm screw diameter onwards incl. adapter (basic equipment up to 1.100 kn) > arrels for up to 3 injection units, /D ratio 20:1 for all diameters > Open nozzle with M60x3 connection thread from screwdiameter 30 mm. Up to 18-25 mm connection thread M40x3 > Extended open nozzle > Pneumatic shut off nozzle incl. control > Needle valve nozzle > Melt temperature measurement can be specified for each injection unit (only with open nozzles) > Controlled barrel heating zones (ceramic heaters), number of zones dependent on injection unit, and one controlled nozzle heating zone > Each temperature control circuit with setpoint deviation control and thermocouple break restistance; barrel operating temperatures up to 450ºC, above 400 ºC with pressure limitation > Integrated hot runner control, 1 to 16 zones, from 1.250 kn up to 24 zones > ydraulic control for hot runner valve gates (possible for each injection unit) Injection unit > ack-pressure profile can be set in several steps on each injection unit > Switch-over to follow-up pressure depending on hydraulic pressure, with acquisition of maximum value and pressure recording to both injection units > Switch-over to holding pressure depending on cavity pressure, with pressure recording for 1 or 2 pressure transducer per injection unit > Programmable nozzle contact pressure (per injection unit) > Resedual nozzle sealing force programmable (per injection unit) > Two-stage injection unit movement with programmable nozzle contact pressure ydraulics > Double pump for simultaneous movements on clamp unit and for separate oil supply for both injection units > Separate circuits for oil an mould cooling > Closed-loop control of oil temperature depending on temperature reading > Pre-heating circuit for hydraulic oil > Ports for external oil cleaning during production (bypass filtration) > utomatic control and display of oil filter contamination > dditional integrated oil cleaning unit for microfine bypass filtration > Pneumatic control for hot runner valve gates (possible for each injection unit) Electronics > ydraulic screw motor for high screw speeds (rpm) (can be specified for each injection unit) > Ergocontrol: Operator-friendly NC4 microprocessor-based operating panel with large colour monitor, alphanumerical keyboard, and disk drive option for data downloads > ydraulic screw drive for high torque (can be specified for each injection unit) > Operation of the second injection unit via Ergocontrol (separate function keys) > requency regulated electrical screw drive (from 1.250 kn; only for injection unit 1) > Stainless steel feed hopper > Drill pattern for material conveyor > dditional operating panel on the non-operating side with keys for injection unit forward/back, screw forward/back and metering (only for -version) > Setpoint entry switch-over to physical values (bar, ccm, mm/s...) > Closed-loop control for feed zone temperature (per injection unit) > ault log with trouble shooting hints > arrel quick change with central connectors for heaters and thermocouples, and automatic barrel recognition > Injection unit regulated via servo valve (available for each injection unit) > djustable profiles for closed-loop control of injection speed, holding pressure, back pressure and screw speed parameters > Quality control with reject parts recognition > Integrated disk drive for software downloads and saving machine and peripheral set-up data > Universal printer port > Print programme for external printer > Injection with DE pump and closed-loop control of pressures and speed > ydraulic central accumulator for high injection capacity and dynamic acceleration > Integrated printer including driver software > Smart card reader for controlled access > dditional Ergocontrol operating language 30

Equipment Multi 50... 420 unctions > unctions and programs apply to both injection units > Process data acquisition with 100% control as well as graphic recording of process parameters Interfaces > Drill pattern for handling device conf. to VDM 24466 (from 1.250 kn) > 32-pin handling device interface conf. to Euromap 67 (VDM) > Integrated Statistical Process Control (SPC) with display of process control charts > Data interface for three signals: drycycling, automatic, and semi-automatic operation > Saving of statistical data in SCII format on disk > Integrated production data acquisition (DE) > Change log > dditional operating language > Three-stepped start-up programme each injection unit separat inspire > On/Off program (without purging), effective for both injection units > lexible movement of the clamp unit with or without multiple movement of the ejector and core pullers > Data interface for main computer systems in accordance with Euromap 63 > Ergolink modem interface > Portable Ergolink modem utomation > Quality reject feature in part removal > Integrated handling device with separate control cabinet > Integrated handling device with integrated control cabinet > lexible sequence for machine movements (setting injection unit functions) > Integrated temperature controllers (2 circuits) > Simple switching of machine to "mono" operation > Precise regulation with real-time stroke measurement > 1, 2, 3, 5, or 6 freely programmable inputs/outputs Interfaces > VG interface and interface for T keyboard (M-II standard) > Interfaces for ejector end switch in mould > Interface for mould protection (ejector plate safety) > Interface for failure monitoring > Interface for slide bar safety > CN-us interface for temperature controllers (2 circuits), signal specified according Demag > Mould temperature display with monitoring for 1 or 2 circuits > Interface with three-point controllers for 2 temperature controllers > Interface with three-point controllers for 4 temperature controllers (from 1.250 kn) > 20m interface (TTY-V24) for up to 6 units integrated temperature controllers (6 single or3twincircuits) > dditional two-point controller for nozzle heater band (can be specified for each injection unit) > Socket for second nozzle heater band (can be specified for each injection unit) > Drill pattern for handling device according Demag shot weight = melt correction factor x swept volume The melt correction factor takes into account the change in volume at process temperature and also includes a factor for the flow characteristics of the shut off device on the end of the screw General > Separate power supply for both drive and heating (basic equipment from 1.250 kn) > Single-phase 230V/50z/6mp socket in specific national version > Set of sockets in separate cabinet near fixed platen on non-operator side, with lockout through mains switch and switch-off matrix, 2x 16 three-phase IECEE and 2x 10 C shockproof plugs in specific national versions > Supply voltage 400V, 3/N/PE, 50 z > Specific national supply voltage > "Supply voltage I/O" switch > asic equipment in compliance with European safety standard (EN 201) > asic equipment in compliance with national safety standards > ault indication by flashing signal > ault indication by acoustic alarm > reely assignable output for fault indication > Maintenance display > lexible machine supports with rubber-to-metal components (anti-vibration mounts) > Three-colour paint trim: machine bed and injection unit light grey R 7035, clamping unit dark grey R 7016; cladding light grey R 7035, red R 3003, ultramarine R 5002 or light blue 571C MD > Paintwork to customer's specification asic equipment dditional price We reserve the right to make changes as a result of further technical advances 31

Machine dimensions and nozzle range of adjustment EER- unit Range of nozzle adjustment for the EEV and EE units O V ges. EV V E Vmax. Vmin. Typ Multi 50 Multi 80 Multi 110 Multi 125 Multi 150 Multi 200 Multi 250 Multi 350 Multi 420 345 375 415 475 520 600 272.5 307.5 342.5 330 375 415 475 475 550 Range of EEV unit nozzle adjustment for ET50 to ET110 EEV-Modul Injection unit PZE EV*) V Vmin Vmax Vges O Ø14 159 35 Ø18 293 400 90 240 480 Ø18 298 80 Ø22 369 505 90 240 480 Ø22 319 120 Ø25 381 505 90 240 480 Ø25 291 200 Ø30 414 505 110 240 480 Ø30 206 310 Ø35 350 470 110 240 480 230 Range of EEV and EE unit nozzle adjustment for ET125 to ET420 EEV-Modul EE-Modul Injection unit PZE EV*) V Vmin Vmax Vges O E*) Vmin Vmax Ø14 109 35 Ø18 243 400 90 230 430 Ø18 248 154 80 Ø22 319 505 90 230 430 225 550 85 300 Ø22 269 225 120 Ø25 331 505 90 230 430 287 550 85 300 Ø25 241 90 287 200 Ø30 364 505 110 230 430 410 550 85 300 Ø30 156 72 310 Ø35 300 470 110 230 430 230 216 306 85 300 Ø35 177 216 430 Ø40 300 470 110 230 430 230 339 400 85 300 Ø40 137 183 600 Ø45 293 470 110 230 430 230 339 400 85 300 *) Values apply only to SVO

Range of nozzle adjustment for the EEV and EE units Machine dimensions and nozzle range of adjustment R-version R ER D Typ Multi 150 ca. 2920 Multi 200 ca. 2950 Multi 250 ca. 2985 Multi 350 ca. 3005 Multi 420 ca. 3130 Injection unit PZE D*) ER R Ø18 80 Ø22 150 20 500 Ø22 120 Ø25 150 20 500 Ø25 200 Ø30 150 20 500 Ø30 310 Ø35 150 20 500 Ø35 430 Ø40 150 20 500 Ø40 600 Ø45 150 20 500 *) Standard distance, alternative distances subject to consultation Multi rotary table, integrated 50,8 203,2 Ø D M øe G-(connecting thread) Z- cooling circuits 10 mm dia min.(cooling channels) 30 l/min (max. flow rate) ø N1 dia. through-hole with rotary manifold ø N2 dia. through-hole without rotary manifold MG ø27 (8x) T 50 P 50,8 K Max. mould diameter øc earing diameter Rotary table thickness x rea without ejector 207; 10 depth Q 50 Typ C D E G * K M N1 N2 MG T P Q Z Multi 125/475 540 515 260 620 675 3/8 97 139,7 75-12 40 M16 32 100-2 Multi 150/500 570 570 260 670 730 3/8 97 139,7 75-12 40 M16 32 100-2 Multi 200/560 640 640 270 760 810 3/8 107 203,2 80 60 26 110 M20 40 200-4 Multi 250/630 720 720 310 870 920 3/8 107 203,2 80 60 26 110 M20 40 200-4 Multi 350/710 815 735 320 920 985 3/8 107 203,2 80 60 26 110 M20 40 225-4 Multi 420/810 930 830 320 1070 1120 1/2 117 203,2 180 70 25 175 M20 40-250 6

Practical values of melt correction factor for use in calculation of shot weight for some common plastics Material Melt correction factor D-PE 0,75 D-PE 0,73 PP 0,73 PS 0,91 S 0,91 S 0,91 SN 0,91 P 0,93 P 6 +30 % G 1,14 PC 0,97 PC/S 0,94 PMM 0,97 POM 1,15 PET 1,08 PT 1,08 C 1,03 C 0,98 PVC-w 1,05 PVC-h 1,15 The melt correction factor takes into account the change in volume at process temperature and also includes a factor for the flow characteristics of the shut off device on the end of the screw Certified according to VD 6.4 Sumitomo (SI) Demag Plastics Machinery Gmb ltdorfer Str. 15 90571 Schwaig Tel.: +49-9 11-50 61-0 ax: +49-9 11-50 61-2 65 E-Mail: info-dpde@dpg.com www.sumitomo-shi-demag.eu 18311265 gb fd shot weight = melt correction factor x swept volume