June 2003 Hydropac Hydropac Waterside Control Fan Coil Units For Horizontal and Vertical Applications Features Flush panel extra rigid construction. Low noise levels. Eleven speed transformer. Full acoustic and thermal insulation. Various filter options. All types of controls available, fitted and wired. Outputs available up to 6.4kW cooling and 6.9kW heating. Horizontal Hydropac PHW173 Illustrated Designed and Built in Britain Patent Nos. Pending
Hydropac PHW230 and PHW170 Series Hydropac (Series PHW) Actionair Hydropac horizontal ceiling void mounted type fan coils are waterside control, suitable for operation against moderate duct resistances, using chilled water cooling medium and low pressure hot water heating medium. Temperature control is by means of modulating 4-port diverting valves on heating and cooling, operated by stand alone or BMS controller with room or return air temperature sensor. Designated PHW, the series consists of standard 230mm (PHW230) deep and slimline 170mm (PHW170) deep versions. Robust construction 1.6mm top panel and fan deck, all other panels 1.2mm galvanised steel. Interchangeable spun steel spigots and insulated blanking plates. High quality EBM Ziehl external rotor motor fans. Fully insulated with Class O open cell thermal and acoustic foam. Quick installation with recessed reinforced slotted mounting points. 2
Hydropac Detail Construction Easy filter removal with three filter options: EU3 Filter Media. EU2 Metal Mesh. Commissioning filter (EU2 Metal Mesh + Media Filter.) High performance coils with vents and drains. Circuited to provide full contra flow. Pipe support plate. Insulated removable powder coated drain tray, with connection options. Illuminated on/off switch with 3 speed fan and fine adjustment switches. Giving 9 speeds on exterior of units. Enclosure incorporating 11 speed transformer with 24 volt output for FCU controller. 3
Hydropac PHW 230 Series PHW 230 Series Waterside control 230mm deep ceiling void mounted chassis unit Thermal Performance Data 11 C min air off 14 C min air off ChW 6 C flow, 11 C return ChW 10 C flow,14 C return LPHW 82 C flow 72 C return Model Speed Airflow Sensible Total Sensible/Total Cooling Heating Fan Input N.R. Setting (I/s) Cooling Cooling (Watts) (Watts) (Watts) Guide* (Watts) (Watts) 2 75 905 1040 730 1050 33 30 3 85 990 1125 790 1130 47 32 PHW231 4 100 1120 1255 880 1240 57 35 5 115 1240 1385 980 1345 66 38 6 125 1325 1475 1050 1415 78 40 2 110 1530 1890 1180 2150 50 30 3 125 1710 2080 1300 2290 70 32 PHW232 4 150 2020 2430 1520 2500 90 35 5 175 2320 2800 1730 2700 110 38 6 185 2400 2890 1780 2800 144 40 2 90 1310 1640 1010 1960 60 30 3 120 1620 2000 1240 2220 75 32 PHW232X 4 160 2110 2540 1570 2500 114 35 5 200 2690 3240 1990 2900 125 38 6 230 3050 3720 2260 3200 160 40 2 175 2450 3020 1830 3200 110 30 3 200 2800 3460 2070 3400 140 32 PHW233 4 240 3360 4150 2460 3800 180 35 5 280 3920 4850 2870 4100 220 38 6 305 4270 5270 3110 4400 270 40 2 170 2660 3460 1970 3810 110 30 3 210 3200 4160 2360 4200 140 32 PHW234 4 255 3650 4950 2820 4610 220 35 5 300 4000 5740 3280 5010 275 38 6 330 4200 6050 3530 5300 370 40 2 195 2800 3400 2150 4110 165 30 3 235 3350 4050 2610 4410 200 32 PHW234X 4 290 4000 4770 3180 4910 240 35 5 340 4300 4960 3680 5410 300 38 6 375 4500 5100 4010 5700 356 40 2 185 2650 3210 2000 4510 165 30 3 225 3100 3710 2400 4910 200 32 PHW235 4 280 4000 4830 3010 5410 290 35 5 340 4800 5800 3640 5910 365 38 6 375 5300 6400 3920 6310 495 40 2 230 3300 4010 2550 4910 227 30 3 275 3900 4720 2990 5410 288 32 PHW235X 4 340 4800 5800 3640 5910 364 35 5 405 5400 6370 4290 6510 440 38 6 445 5600 6450 4670 6910 556 40 The Fan Coil selections are based on the following entering air conditions: Cooling: Summer On-coil air 23 C Dry Bulb, 16 C Wet Bulb. Max Coil Pd = 20kPa Heating: Winter On-coil air temperature 20 C Dry Bulb. Max Coil Pd = 10kPa General: External Resistance 30Pa. Electrical Supply 230 Volts/ 1 phase /50 Hz. Please refer to our Fan Coil Technical Department for alternative conditions. * see page 7 for NR Predictor. 4
Hydropac PHW 230 Series PHW 230 Series Dimensions Model Dim A Dim B Weights Spigots PHW 231 380 350 25kg 1-4-7 PHW 232/2X 730 700 35kg 1-2-6-7 PHW 233 1080 1050 50kg 1-2-4-6-7 PHW 234/4X 1430 1400 70kg 1-2-3-5-6-7 PHW 235/5X 1780 1750 90kg 1-2-3-4-5-6-7 5
Hydropac PHW 170 Series PHW 170 Series Waterside control 170mm deep ceiling void mounted chassis unit Thermal Performance Data 11 C min air off 14 C min air off ChW 6 C flow, 11 C return ChW 10 C flow,14 C return LPHW 82 C flow 72 C return Model Speed Airflow Sensible Total Sensible/Total Cooling Heating Fan Input N.R. Setting (I/s) Cooling Cooling (Watts) (Watts) (Watts) Guide* (Watts) (Watts) 2 90 1192 1407 978 1982 40 30 3 105 1385 1602 1120 2187 50 32 PHW172 4 120 1532 1786 1255 2357 62 35 5 135 1701 1673 1394 2525 74 38 6 155 1928 2225 1579 2742 89 40 2 145 1893 2225 1550 3081 80 30 3 170 2187 2257 1790 3390 101 32 PHW173 4 185 2380 2751 1932 3355 133 35 5 205 2592 3011 2123 3772 160 38 6 235 2941 3403 2410 4092 189 40 2 155 2237 2738 1675 3655 80 30 3 180 2573 3136 1916 4026 101 32 PHW174 4 195 2774 3374 2067 4246 133 35 5 215 3035 3680 2268 4519 160 38 6 245 3399 4092 2557 4861 189 40 2 200 2825 3427 2127 4740 113 30 3 230 3228 3905 2423 5191 143 32 PHW175 4 245 3429 4145 2577 5415 187 35 5 265 3696 4481 2786 5706 224 38 6 290 4002 4808 3031 5997 267 40 The Fan Coil selections are based on the following entering air conditions: Cooling: Summer On-coil air 23 C Dry Bulb, 16 C Wet Bulb. Max Coil Pd = 20kPa Heating: Winter On-coil air temperature 20 C Dry Bulb. Max Coil Pd = 10kPa General: External Resistance 30Pa. Electrical Supply 230 Volts/ 1 phase /50 Hz. Please refer to our Fan Coil Technical Department for alternative conditions. * see page 7 for NR Predictor. Dimensions Unit Dim A Dim B Dim C Weight SPIGOT OPTIONS PHW 172 730 700 225 32kg 1-2-4-7-8 PHW 173 1080 1050 267 45kg 1-2-3-6-7-8 PHW 174 1430 1400 287 65kg 1-2-3-4-6-7-8 PHW 175 1780 1750 300 85kg 1-2-3-4-5-6-7-8 6
Hydropac PHW 230 / 170 Series Acoustic Performance Data Typical Horizontal Fan Coil Unit Arrangement Fresh air supply duct. Fan coil unit. Minimum 1 metre length Sonodec 25 acoustic flex. Diffuser plenum. Building structure. Wall/glazing. Return air grille/diffuser (not positioned directly below unit intakes). T Bar grid false ceiling with either 10mm thick fibre board tiles or insulated metal pan tiles. Internal room. * Notes on NR predictions NR predictions quoted are based upon extensive acoustic independent tests to the above arrangement and are intended as a guide to levels which can be expected. The following qualifications must apply:- Units must be mounted correctly, using rubber washers, onto a solid structure. The units should be mounted into a false ceiling of not less than 300mm deep, constructed of a standard T bar grid with 10mm thick fibre board tiles or insulated metal pan tiles. Rooms of open plan or partitioned design should be furnished, carpeted and have no more than 20% glass area with no highly reflective surfaces such as ceramic tiles etc. Where a single unit is serving a room the dimensions should be based upon a cooling load of 120w/sq.m e.g a unit giving 1.2kW total cooling output should be serving a room with a floor area of not less than 10sq.m. In an open plan area units should be mounted at a minimum of 4.5m centres and no closer than 1.5m from a corner. Return air grilles should not be positioned directly below unit intakes. At least 1m of acoustic flexible ducting (Sonodec 25 or similar) is used on each spigot outlet. A maximum air velocity of 3.0m/s per outlet spigot to achieve NR35. The above should give the predicted Lp at 1.5m from the nearest diffuser. For detailed acoustic data of Inlet/Casing Radiated and Discharge Sound Power Levels, please refer to Actionair Sales Office. 7
Hydropac PVW230 Series Detail Constru Hydropac (Series PVW) Actionair vertical chassis and cased wall mounted fan coils are waterside control, suitable for free-blow, applications or vertical ducted arrangements operating up to 60 Pa external resistance, using chilled water cooling medium and low pressure hot water medium. Temperature control is by means of modulating 4-port diverting valves on heating and cooling. Designated PVW the series consists of five models 230mm deep, with six non-cased/cased variations. Protected control enclosure. Discharge spigot can be vertical or horizontal. Slide out filters. EBM Ziehl external rotor motor fans. Condensate removal pump when used. Removable front access. 8
Hydropac ction PVW 230 Cases Options and Mounting Arrangements Option 1. Low level mounting with front angled grille outlet. Option 2. Low level mounting with front angled grille outlet and front face grille inlet. Option 3. High level mounting as per option 2 but with protection panel on underside. Option 4. High level mounting with front grille outlet and underside grille inlet. 9
Hydropac Series PVW 230 PVW 230 Series 230mm deep vertical wall mounted chassis / cased units Thermal Performance Data 11 C min air off 14 C min air off ChW 6 C flow, 11 C return ChW 10 C flow, 14 C return LPHW 82 C flow 72 C return Model Speed Airflow Sensible Total Sensible/Total Cooling Heating Fan Input N.R. Setting (I/s) Cooling Cooling (Watts) (Watts) (Watts) Guide* (Watts) (Watts) 2 40 419 463 350 704 17 30 3 50 489 534 380 829 20 32. PVW231 4 60 557 570 400 883 22 35 5 60 557 605 410 934 25 38 6 70 617 668 430 1017 28 40 2 90 888 971 778 1737 32 30 3 100 957 1041 840 1851 36 32 PVW232 4 110 1025 1113 903 1964 40 35 5 120 1093 1185 968 2077 45 38 6 130 1162 1259 1034 2188 49 40 2 115 1292 1446 1017 2458 50 30 3 140 1525 1695 1170 2757 60 32 PVW233 4 160 1715 1898 1296 2992 65 35 5 180 1905 2105 1428 3224 75 38 6 215 2229 2455 1666 3604 90 40 2 140 1530 1701 1246 3066 58 30 3 160 1702 1881 1363 3303 63 32 PVW234 4 200 2057 2263 1608 3767 80 35 5 220 2241 2463 1738 3995 90 38 6 240 2428 2866 1873 4220 100 40 2 185 1925 2122 1578 4018 85 30 3 225 2213 2428 1784 4436 120 32 PVW235 4 250 2472 2706 1970 4788 150 35 5 275 2697 2949 2133 5078 165 38 6 320 3117 3404 2449 5594 185 40 The Fan Coil selections are based on the following entering air conditions: Cooling: Summer On-coil air 23 C Dry Bulb, 16 C Wet Bulb. Max Coil Pd = 20kPa Heating: Winter On-coil air temperature 20 C Dry Bulb. Max Coil Pd = 10kPa General: External Resistance 10Pa. Electrical Supply 230 Volts/ 1 phase /50 Hz. * see page 11 for NR Predictor. Chassis Dimensions Unit Dim A Dim B Weight PVW 231 785 310 30kg PVW 232 1035 660 43kg PVW 233 1385 1010 62kg PVW 234 1735 1360 86kg PVW 235 2085 1710 110kg 10
Hydropac Series PVW 230 PVW 230 Series * Notes on NR predictions Case Dimensional Data NR predictions are based upon extensive acoustic independent tests and are intended as a guide to levels which can be expected, when measured at 2.0m. The following qualifications apply:- Units must be mounted correctly, using fixing points provided onto a flat, solid surface, such as concrete or brick wall in such a way that they are not subjected to undue stress and are checked for accuracy of horizontal levelling. Rooms of open plan or partitioned design should be furnished, carpeted and have no more than 20% glass area with no highly reflective surfaces such as ceramic tiles etc. Where a single unit is serving a room the dimensions should be based upon a cooling load of 120w/sq.m e.g a unit giving 1.2kW total cooling output should be serving a room with a floor area of not less than 10sq.m. In an open plan area units should be mounted at a minimum of 3m centres and no closer than 1.5m from a corner. Units installed in accordance with the above should give the predicted N.R. level when measured at a distance of 2.0m from any surrounding flat surface. For detailed acoustic data of Radiated Sound Power Levels, please refer to Technical Sales Office. Option 1 Case Option 2 and 3 Case Option 4 Case Unit Dim A Dim B Weight PVW 231 815 310 35kg PVW 232 1065 660 50kg PVW 233 1415 1010 70kg PVW 234 1785 1360 95kg PVW 235 2115 1710 120kg 11
Actionair www.actionair.co.uk Also available NEW Environpac EMC Motor Technology 40% Less Motor Energy 1/3 Less Fan Heat Constant Volume NEW Systempac Fancoil, Ductwork and Diffuser Package Fast Track Delivery Fully Acoustically Tested Sample Design Selection Aeropac Airside Control Fancoil 230mm Deep Horizontal Mounted High Energy Efficiency Technical Support Actionair provide quality products backed by a dedicated team committed to providing the very best in customer service. Specialist response from the Actionair Sales Team, administrative response from the Computerised Sales Office and product maintenance from the Team of Experienced Service Engineers, who understand fully the needs of the industry. Actionair Products For information on our comprehensive range of Fire, Smoke and Air Control Dampers, as well as Application, Technical and Pricing Advice, please refer to the Actionair Sales Office. NO COMPROMISE Quality System Certificate No 017 Assessed to ISO 9001 : 2000 Actionair, South Street, Whitstable, Kent CT5 3DU England Tel: (01227) 276100 Fax: (01227) 264262 International Code: +441227 Email: sales@actionair.co.uk Website: www.actionair.co.uk The information contained herein is subject to change without notice due to continuing research and development. PRODUCED BY GRAPHIC PARTNERSHIP 01227 280877 Part of Ruskin Air Management Limited