DIESEL FUEL FILTER/WATER SEPARATORS & Recycler Systems

DIESEL FUEL FILTER/WATER SEPARATORS & Recycler Systems

DAHL DIESEL FUEL FILTER/WATER SEPARATORS REMOVE DIESEL FUEL SYSTEM PROBLEMS ALONG WITH WATER Water and solid contaminants displace the diesel fuel s lubricative coating on high precision injection components. The loss of this protection results in wear, erosion, surface pitting and eventual pressure loss. Many existing fuel filters aren t designed to remove significant amounts of water. They are designed to do their job in a single step. This means they must be porous enough to allow sufficient flow volume which, in turn, limits filtering ability to between 10 and 30 microns. Any tighter media would plug too quickly and result in frequent element changes. The DAHL system takes care of those shortcomings. DAHL s functional dual-chamber 3-stage diesel fuel filter/water separators provide efficient suction side water separation and contaminant filtration. The key is the unique DAHL patented depressurizer cone which spreads the flow of the fuel. With more area to flow over, greater separation of water and dirt from the fuel is achieved. DAHL diesel fuel filter/water separators have less mechanical flow resistance than other separators, because the fuel changes direction only twice. The DAHL unit removes virtually 100% of the water and most of the contaminants from the diesel fuel. Why DAHL Is Right For Your Diesel Equipment 1. The DAHL system eliminates water from fuel before reaching the fuel pump and injectors. This prevents the major cause of diesel fuel injection system failure. a. It prolongs system life by eliminating pump and injector overhauls caused by water contaminated fuel. The cost of shop labor alone, just to repair the injection system on a 6-cylinder rig, exceeds the cost of the DAHL diesel fuel filter/water separator. b. It reduces the need to repair the fuel pump and/or injectors that could easily tie up equipment for one or two days. The loss of income in just a few hours of equipment downtime again would pay for a DAHL diesel fuel filter/water separator.. The DAHL system separates solid contaminants from the fuel before reaching the fuel pump and injectors. 3. The DAHL system is easily installed. a. Install it at any location before the fuel pump. (Complete installation instructions are included with each DAHL unit.) b. This system can replace all other primary filters and water separators. It both filters and separates. c. It takes minimal space to install. Clearance space for element removal is between 1 1/ to 3 1/ inches. Some models are installed with as few as two easily accessed bolts. 4. The DAHL system is easily serviced. a. Models 150, 00 and 300 are serviced by loosening the T-Bolt handle. They also feature a self-ejecting element. b. The transparent bowl (up to 4 ounce water capacity) makes constant draining unnecessary. The draincock is easy to use. An aluminum bowl is also available. 5. Most of the solid contaminants are separated by the patented depressurizer cone in the bowl BEFORE reaching the filter element. Another factor resulting in less frequent changes is the extra paper in the filter element. Under normal conditions, the element can last up to 40,000 miles. 6. The DAHL system includes a reverse flow valve. This holds the prime in the fuel system by not allowing flow back to the tank during shut-down. (Removable primer plug at top assists where complete priming is required.) 7. The DAHL system helps eliminate air entrapment because the inlet and outlet ports are at the top of the unit. The fuel changes directions only twice (see flow diagram), and so offers less mechanical resistance. Less resistance means longer pump and element life. PROVEN PERFORMANCE in the laboratory and in millions of miles/hours of commercial and industrial operation. You can be sure that each DAHL unit is designed right, built right and does its job right. MARINE DURABILITY is assured. Marine units 75, 100-M, 150-M, 00-M, 00-MMV, 300-M and 300-MMV have passed severe U.L. testing. Tests include fire endurance, vibration fatigue, impact and thermal shock. These filters have also met U.S. Coast Guard requirements for Marine Applications. CLEAN FUEL provided by a DAHL diesel fuel filter/water separator eliminates nearly all of the engine problems caused by water and solid contaminants in diesel fuel. In addition, you can expect: Longer Injection System Component Life Full Power Performance Lower Element Replacement Cost 1

Here s How The DAHL System Works 1. The contaminated fuel enters the inlet port.. The T-Bolt redirects the fuel downward through the centerpipe. 3. Fuel flows through the reverse flow valve. 1 3 4 5 6 7 4. Fuel flow is spread by the depressurizer cone. 5. As fuel is discharged from the depressurizer cone, 80% of contaminant separation takes place. Most of the solid particles and water settle into the quiet zone of the bowl. 6. As the fuel rises upward, any remaining minute water droplets coalesce on the cone, baffle and bowl surfaces. Droplet size and weight gradually increase, causing downward flow into the sump. 7. Fuel is filtered completely by the element, which contains HydroShield media. The clean fuel then continues upward through the outlet port and on to the pump and injection system. How To Select The Right DAHL Filter Choose the size which can accommodate the flow rate recommended in the chart. (Maximum flow rate listed is for convenience in comparing with other systems only.) For most efficient separation and filtration, select from the recommended column. Flow Rates in Gallons Per Hour The chart is for Fuel/Water Separators. Recyclers are limited by the pump. For example, a single 300 recycler unit has a flow rate limited to 180 GPH (U.S.), and a double 300 recycler unit has a flow rate limited to 360 GPH (U.S.). Flow Rates GPH (U.S.) Model Series Recommended Maximum Sump Capacity 65 & 75 0 30 4 oz. 100 40 65 8 oz. 100 Double 80 130 16 oz. 150 80 100 8 oz. 150 Double 160 00 16 oz. 00 10 00 4 oz. 00 Double 40 400 48 oz. 300 180 35 4 oz. 300 Double 360 650 48 oz. 300 Triple 540 975 7 oz. 500 1800 190 11 Gallons 500 Double 3600 3840 Gallons All Multiple Multiply Flow Rate and Sump Capacity Units by Number of Units Superior Engineering Die cast aluminum Impact-resistant large transparent bowl Element service life is several times longer than conventional Easy to install, service and clean Positive air elimination Advanced spring design assures positive element seal Less mechanical resistance because of streamlined flow path Baffle system is designed to stop emulsification and disperse trapped air Ball check valve to stop reverse flow Six series specifically designed to fit diesel engines of various capacities

65 & 75 Series Compact Fuel Filter/Water Separators Specifications MODEL 65 Diesel Fuel Filter/Water Separator Flow Resistance:...0.75 In. Mercury Maximum Working Pressure:...5 PSI (17 kpa) Temperature Range:...-50 to +5 F (-45 to +107 C) Port Thread:...9/16-18 w/o-ring Boss Height / 65:...6 3/8 In. (161.9 mm) Height / 75:...6 1/8 In. (155.6 mm) Width:...4 3/16 In. (106.4 mm) Depth:...4 3/4 In. (10.6 mm) Element Removal Clearance:...3 1/ In. (88.9 mm) Sump Capacity:...4 oz. (118 ml) Flow Rates Model 65 & 75 Series: Recommended:...0 GPH (U.S.) (75.7 LPH) Maximum:...30 GPH (U.S.) (113.5 LPH) Service Parts Elements: 61...(For Use on Model 60)...4 Micron Nominal (0 Absolute) Element 61-W...(For Use on Model 60)...5 Micron Nominal (5 Absolute) Element 66*...(For Use on Models 65 & 75)...4 Micron Nominal (0 Absolute) Element 66-W...(For Use on Models 65 & 75)...5 Micron Nominal (5 Absolute) Element 66-30...(For Use on Model 65, 65-W30 & 75, 75-W30)...9 micron nominal (40 absolute) Gaskets: 60-GK...Complete Gasket Kit for 60, 65 & 75 Form 4060: Installation, Operation, Parts & Service Information DAHL Model 60 Parts: Call for Availability Used On 65 & 75 Small Diesel Engines Where Space is Limited 75 Small Gasoline Engines & Marine Applications Cars & Light-Duty Trucks MODEL 75 Gasoline or Diesel Fuel Filter/Water Separator with Aluminum Bowl 65 & 75 Series Single Units 65 Diesel Fuel Filter/Water Separator 65-W30 Diesel Fuel Filter/Water Separator (30 Micron Element) 75 Gasoline or Diesel Fuel Filter/Water Separator with Aluminum Bowl U.L. Listed. Meets U.S. Coast Guard requirements. 75-W30 Gasoline or Diesel Fuel Filter/Water Separator with Aluminum Bowl (30 Micron Element) Accessories All Inlet & Outlet Fittings Require O-Ring Seals Fittings...See DAHL Fittings Chart 66*,-30,-W Primer Plug O-Ring (Incl. in 60-GK) Lid Bowl Gasket (Square Cut) (Incl. in 60-GK) Element 65-35A Pipe/ Depressurizer Assembly 60-1A Bowl Assembly (60-30 Draincock Included) 60-30 Draincock Mounting Hole Pattern Clearance for 5/16 In. Diameter Fasteners + + + + 1.81 in. 65 Series 75 Series (46 mm).1 in. (54 mm) + + 66*,-30,-W Primer Plug O-Ring (Incl. in 60-GK) Lid Bowl Gasket (Square Cut) (Incl. in 60-GK) Element 65-35A Pipe/ Depressurizer Assembly 75-1 Aluminum Bowl Brass Pipe Plug * Standard with Unit Unless Stated. U.L. Listed. Meets U.S. Coast Guard Requirements for Marine Applications. 3

100 Series Diesel Fuel Filter/Water Separators MODEL 100 Diesel Fuel Filter/Water Separator Specifications Flow Resistance:...0.75 In. Mercury Maximum Working Pressure:...5 PSI (17 kpa) Temperature Range:...-50 to +5 F (-45 to +107 C) Port Thread: Single Units:...9/16-18 w/o-ring Boss Double Units:...1/4-18 NPT Height:...1 1/ In. (317.5 mm) Width:...5 1/ In. (139.7 mm) Depth:...6 1/ In. (165.1 mm) Element Removal Clearance:...1 1/ In. (38.1 mm) Sump Capacity:...8 oz. (36 ml) MODEL 100-M Marine Diesel Fuel Filter/Water Separator Flow Rates Single Model 100 Series: Recommended:...40 GPH (U.S.) (151 LPH) Maximum:...65 GPH (U.S.) (46 LPH) Double Model 100 Series: Recommended:...80 GPH (U.S.) (30 LPH) Maximum:...130 GPH (U.S.) (49 LPH) MODEL 100-MFV Double Manifold Diesel Fuel Filter/Water Separator with Shut-Off Valves for Continuous Operation Service Parts Elements: 101*...4 Micron Nominal (0 Absolute) Element 101-W...5 Micron Nominal (5 Absolute) Element 101-30...9 Micron Nominal (40 Absolute) Element Gaskets: 100-GK...Complete Gasket Kit (See Accessories Page) Kits: 100-DEPR KIT...Depressurizer Kit (See Accessories Page) 100-MNTG KIT...Mounting Bracket Kit...(See Accessories Page) Form 4100: Installation, Operation, Parts & Service Information Form 413: Marine Installation, Operation, Parts & Service Information MODEL 100-MMV Double Marine Manifold Diesel Fuel Filter/Water Separator with Shut-Off Valves for Continuous Operation 4 U.L. Listed. Meets U.S. Coast Guard Requirements for Marine Applications. * Standard with Unit Unless Stated.

100 Series Diesel Fuel Filter/Water Separators Cont d. Accessories All Inlet & Outlet Fittings Require O-Ring Seals Aluminum Bowl...100-1AL Clear Bowl w/water Sensor Probes...100-1BP Clear Bowl w/heater Probes...100-1H Clear Bowl w/marine Collar for Marine Units...100-1M Fittings...See DAHL Fittings Chart Heat Deflector Shield for Marine Units...185-DS Heater Kit...See Accessories Page (Heater Kits & Heater Parts) Shock Pad Mounting Kit...186-SK Water Sensor Warning Light Kit (Use with 100-1BP) 4 Volt DC...4-WLK 100 Series Single Units 100 Diesel Fuel Filter/Water Separator 100-BP Diesel Fuel Filter/Water Separator with Water Sensor Bowl Probes Order Warning Light Kit separately. 100-H Diesel Fuel Filter/Water Separator with In-Filter Heater Dash-Mounted Toggle Switch included. Operates on either 1 or 4 Volt systems. (10 Micron Element) 100-M Marine Diesel Fuel Filter/Water Separator U.L. Listed. Meets U.S. Coast Guard requirements. 100-W Diesel Fuel Filter/Water Separator (5 Micron Nominal (5 Absolute) Element) 100-W30 Diesel Fuel Filter/Water Separator (9 Micron Nominal (40 Absolute) Element) Used On Small Diesel Engines Up to Approx. 00 HP (Except Cummins & Detroit Diesel Engines) Cars, Light-Duty Trucks & RV's Small Pleasure Crafts & Sailboats Caterpillar Engines Thru 3300 Series Small Generators & Farm Tractors Refrigeration Units 5.7L & 6.L GMC Engines + 1.5 in. (31.8 mm) + 3.65 in. (93 mm) Marine + + { Mounting Hole Pattern Clearance for 5/16 In. Diameter Fasteners Mounting Bracket (Incl. in 100-MNTG KIT) Fitting Bracket Bolt, Washer & Nut (Incl. in 100-MNTG KIT) Lid Cover Clamp Knob Seal Clamp with Knob Lid Cover Gasket (Incl. in 100-GK) Centerpipe O-Ring (Incl. in 100-GK) 101*,-W,-30 Element w/gasket Spring Centerpipe Body Reverse Flow Gasket (Incl. in 100-DEPR KIT & 100-GK) Reverse Flow Washer (Incl. in 100-DEPR KIT & 100-GK) Reverse Flow Ball (Incl. in 100-DEPR KIT) Bowl Gasket (Incl. in 100-GK) Depressurizer Set (Incl. in 100-DEPR KIT) 100-1 Bowl Bowl Ring Socket Head Bolt 10-3 x 3/4 (4 required) Bowl Plug O-Ring (Incl. in 100-GK) 100-9 Bowl Plug 100-30 Draincock (1/4 In.) 100 Series Double Manifold Units 100-MFV Two Diesel Fuel Filter/Water Separators Manifolded with Shut-Off Valves Allows continuous operation while servicing. 100-MMV Two Marine Diesel Fuel Filter/Water Separators Manifolded with Shut-Off Valves Allows continuous operation while servicing. U.L. Listed. Meets U.S. Coast Guard requirements. 100-MMV30 Two Marine Diesel Fuel Filter/Water Separators Manifolded with Shut-Off Valves Allows continuous operation while servicing. (9 Micron Nominal (40 Absolute) Element) Aluminum 100-1M Marine Bowl Bowl Ring Socket Head Bolt 10-3 x 3/4 (4 required) Bowl Plug O-Ring (Incl. in 100-GK) 185-DS Heat Deflector Shield 100-9 Bowl Plug Brass Pipe Plug (1/4 In.) 100-1AL Aluminum Bowl Bowl Ring Socket Head Bolt 10-3 x 3/4 (4 required) Brass Pipe Plug (1/4 In.) * Standard with Unit Unless Stated. U.L. Listed. Meets U.S. Coast Guard Requirements for Marine Applications. 5

150 Series Diesel Fuel Filter/Water Separators MODEL 150 Diesel Fuel Filter/Water Separator Specifications Flow Resistance:...0.75 In. Mercury Maximum Working Pressure:...5 PSI (17 kpa) Temperature Range:...-50 to +5 F (-45 to +107 C) Port Thread: Single Units:...7/8-14 w/o-ring Boss Double Units:...3/4-14 NPT Height:...14 1/4 In. (368.3 mm) Width:...6 In. (15.4 mm) Depth:...6 11/3 In. (161.1 mm) Element Removal Clearance:... In. (50.8 mm) Sump Capacity:...8 oz. (36 ml) Flow Rates Single Model 150 Series: Recommended:...80 GPH (U.S.) (30 LPH) Maximum:...100 GPH (U.S.) (378 LPH) Double Model 150 Series: Recommended:...160 GPH (U.S.) (604 LPH) Maximum:...00 GPH (U.S.) (757 LPH) MODEL 150-M Marine Diesel Fuel Filter/Water Separator Service Parts Elements: 151*...4 Micron Nominal (0 Absolute) Element 151-W...5 Micron Nominal (5 Absolute) Element 151-30...9 Micron Nominal (40 Absolute) Element Gaskets: 150-GK...Complete Gasket Kit (See Accessories Page) Kits: 100-DEPR KIT...Depressurizer Kit (See Accessories Page) Form 405:...Installation, Operation, Parts & Service Information Form 413:...Marine Installation, Operation, Parts & Service Information 6 U.L. Listed. Meets U.S. Coast Guard Requirements for Marine Applications. * Standard with Unit Unless Stated.

150 Series Diesel Fuel Filter/Water Separators Cont d. Accessories All Inlet & Outlet Fittings Require O-Ring Seals Aluminum Bowl...100-1AL Clear Bowl w/water Sensor Probes...100-1BP Clear Bowl w/heater Probes...100-1H Clear Bowl w/marine Collar for Marine Units...100-1M Fittings...See DAHL Fittings Chart Heat Deflector Shield for Marine Units...185-DS Heater Kit...See Accessories Page (Heater Kits & Heater Parts) Shock Pad Mounting Kit...86-SK Water Sensor Warning Light Kit (Use with 100-1BP) 4 Volt DC...4-WLK 150 Series Units 150 Diesel Fuel Filter/Water Separator 150-H Diesel Fuel Filter/Water Separator with In-Filter Heater Dash-Mounted Toggle Switch included. Operates on either 1 or 4 Volt systems. (5 Micron Nominal (5 Absolute) Element) 150-M Marine Diesel Fuel Filter/Water Separator U.L. Listed. Meets U.S. Coast Guard requirements. 150-W30 Diesel Fuel Filter/Water Separator (9 Micron Nominal (40 Absolute) Element) Used On Small & Medium Size Heavy-Duty Diesel Engines (Up to Approx. 450 HP) Large Farm Tractors ++ ++ 3.67 in. (93 mm) 5.0 in. (13 mm) Marine { Mounting Hole Pattern Clearance for 3/8 In. Diameter Fasteners Detroit Diesel (53 & Small 71 Series) Some Cummins Six Cylinder Engines T-Bolt T-Bolt O-Ring (Incl. in 150-GK) Lid O-Ring (Incl. in 150-GK) 150-31 Primer Plug Primer Plug O-Ring (Incl. in 150-GK) Lid Cover Lid Cover Gasket (Incl. in 150-GK) Centerpipe O-Ring (Incl. in 150-GK) 151*,-W,-30 Element w/gasket Spring Centerpipe Body Reverse Flow Gasket (Incl. in 100-DEPR KIT & 150-GK) Reverse Flow Washer (Incl. in 100-DEPR KIT & 150-GK) Reverse Flow Ball (Incl. in 100-DEPR KIT) Bowl Gasket (Incl. in 150-GK) Depressurizer Set (Incl. in 100-DEPR KIT) 100-1 Bowl Bowl Ring Socket Head Bolt 10-3 x 7/8 (4 required) Bowl Plug O-Ring (Incl. in 150-GK) 100-9 Bowl Plug 100-30 Draincock (1/4 In.) Aluminum 100-1M Marine Bowl Bowl Ring Socket Head Bolt 10-3 x 7/8 (4 required) Bowl Plug O-Ring (Incl. in 150-GK) 185-DS Heat Deflector Shield 100-9 Bowl Plug Brass Pipe Plug (1/4 In.) 100-1AL Aluminum Bowl Bowl Ring Socket Head Bolt 10-3 x 7/8 (4 required) Brass Pipe Plug (1/4 In.) * Standard with Unit Unless Stated. U.L. Listed. Meets U.S. Coast Guard Requirements for Marine Applications. 7

00 Series Diesel Fuel Filter/Water Separators MODEL 00 Diesel Fuel Filter/Water Separator Specifications Flow Resistance:...1.0 In. Mercury Maximum Working Pressure:...5 PSI (17 kpa) Temperature Range:...-50 to +5 F (-45 to +107 C) Port Thread: Single Units:...7/8-14 w/o-ring Boss Double Units:...3/4-14 NPT Height:...16 3/4 In. (45.5 mm) Width:...7 1/ In. (190.5 mm) Depth:...7 3/4 In. (196.9 mm) Element Removal Clearance:... 1/ In. (63.5 mm) Sump Capacity:...4 oz. (708 ml) Top to Inlet Clearance:... 5/8 In. (66.7 mm) Top to Outlet Clearance:... 5/8 In. (66.7 mm) MODEL 00-M Marine Diesel Fuel Filter/Water Separator Flow Rates Single Model 00 Series: Recommended:...10 GPH (U.S.) (454 LPH) Maximum:...00 GPH (U.S.) (757 LPH) Double Model 00 Series: Recommended:...40 GPH (U.S.) (908 LPH) Maximum:...400 GPH (U.S.) (1,514 LPH) MODEL 00-MFV Double Manifold Diesel Fuel Filter/Water Separator with Shut-Off Valves for Continuous Operation Service Parts Elements: 01*...4 Micron Nominal (0 Absolute) Element 01-W...5 Micron Nominal (5 Absolute) Element 01-30...9 Micron Nominal (40 Absolute) Element Gaskets: 00-GK...Complete Gasket Kit (See Accessories Page) Kits: 00-DEPR KIT...Depressurizer Kit (See Accessories Page) Form 430: Installation, Operation, Parts & Service Information Form 413: Marine Installation, Operation, Parts & Service Information MODEL 00-MMV Double Marine Manifold Diesel Fuel Filter/Water Separator with Shut-Off Valves for Continuous Operation 8 U.L. Listed. Meets U.S. Coast Guard Requirements for Marine Applications. * Standard with Unit Unless Stated.

00 Series Diesel Fuel Filter/Water Separators Cont d. Accessories All Inlet & Outlet Fittings Require O-Ring Seals Aluminum Bowl...00-1AL Clear Bowl w/water Sensor Probes...00-1BP Clear Bowl w/heater Probes...00-1H Clear Bowl w/water Sensor & Heater Probes...00-1HBP Clear Bowl w/marine Collar for Marine Units...00-1M Fittings...See DAHL Fittings Chart Heat Deflector Shield for Marine Units...85-DS Heater Kit...See Accessories Page (Heater Kits & Heater Parts) Shock Pad Mounting Kit...86-SK Water Sensor Warning Light Kit (Use with 00-1BP) 4 Volt DC...4-WLK Used On 8 Cylinder Cummins & Detroit Diesel Engines Caterpillar Engines to Approximately 1,000 HP (Including 399) Most Other Medium Size Diesel Engines to Approximately 1,000 HP Trucks & Buses Construction & Farm Equipment Medium Size Generators Smaller Commercial Boats + + 4.0 in. (101.6 mm) Mounting Hole Pattern Clearance for 3/8 In. Diameter Fasteners 00 Series Single Units 00 Diesel Fuel Filter/Water Separator 00-H Diesel Fuel Filter/Water Separator with In-Filter Heater Operates on either 1 or 4 Volt systems. (10 Micron Element) 00-M Marine Diesel Fuel Filter/Water Separator U.L. Listed. Meets U.S. Coast Guard requirements. 00-W30 Diesel Fuel Filter/Water Separator (9 Micron Nominal (40 Absolute) Element) 00 Series Double Manifold Units 00-MFV Two Diesel Fuel Filter/Water Separators Manifolded with Shut-Off Valves Allows continuous operation while servicing. 00-MMV Two Marine Diesel Fuel Filter/Water Separators Manifolded with Shut-Off Valves Allows continuous operation while servicing. U.L. Listed. Meets U.S. Coast Guard requirements. Marine Aluminum { T-Bolt Nylon Gasket (Incl. in 00-GK) Upper T-Bolt Seal (Incl. in 00-GK) Lower T-Bolt Seal (Incl. in 00-GK) 00-31 Primer Plug Primer Plug O-Ring (Incl. in 00-GK) Lid Cover Lid Cover Gasket (Incl. in 00-GK) Centerpipe O-Ring (Incl. in 00-GK) 01*,-W,-30 Element w/gasket Centerpipe Body Ejector Spring (4 required) Ejector Spring Clip (4 required) Reverse Flow Gasket (Incl. in 00-DEPR KIT & 00-GK) Reverse Flow Washer (Incl. in 00-DEPR KIT & 00-GK) Reverse Flow Ball (Incl. in 00-DEPR KIT) Bowl Gasket (Incl. in 00-GK) Depressurizer Set (Incl. in 00-DEPR KIT) 00-1 Bowl Bowl Ring Socket Head Bolt 1/4-0 x 5/8 (8 required) Bowl Plug O-Ring (Incl. in 00-GK) 100-9 Bowl Plug 100-30 Draincock (1/4 In.) 00-1M Marine Bowl 85-DS Bowl Ring Socket Head Bolt 1/4-0 x 5/8 (8 required) Bowl Plug O-Ring (Incl. in 00-GK) Heat Deflector Shield 100-9 Bowl Plug Brass Pipe Plug (1/4 In.) 00-1AL Aluminum Bowl Bowl Ring Socket Head Bolt 1/4-0 x 5/8 (8 required) Brass Pipe Plug (1/4 In.) * Standard with Unit Unless Stated. U.L. Listed. Meets U.S. Coast Guard Requirements for Marine Applications. 9

300 Series Diesel Fuel Filter/Water Separators MODEL 300 Diesel Fuel Filter/Water Separator MODEL 300-M Marine Diesel Fuel Filter/Water Separator MODEL 300-MFV Double Manifold Diesel Fuel Filter/Water Separator with Shut-Off Valves for Continuous Operation MODEL 300-MMV Double Marine Manifold Diesel Fuel Filter/Water Separator with Shut-Off Valves for Continuous Operation MODEL 300-MFV3 Triple Manifold Diesel Fuel Filter/Water Separator with Shut-Off Valves for Continuous Operation MODEL 300-MMV3 Triple Marine Manifold Diesel Fuel Filter/Water Separator with Shut-Off Valves for Continuous Operation Specifications Flow Resistance:...1.5 In. Mercury Maximum Working Pressure:...5 PSI (17 kpa) Temperature Range:...-50 to +5 F (-45 to +107 C) Port Thread: Single Units:...1 1/16-1 w/o-ring Boss Double Units:...1-11 1/ NPT Triple Units:...1-11 1/ NPT Height:... 1/4 In. (565. mm) Width:...7 1/ In. (190.5 mm) Depth:...7 3/4 In. (196.9 mm) Element Removal Clearance:... 1/ In. (63.5 mm) Sump Capacity:...4 oz. (708 ml) Top to Inlet Clearance:... 5/8 In. (66.7 mm) Top to Outlet Clearance:... 5/8 In. (66.7 mm) Flow Rates Single Model 300 Series: Recommended:...180 GPH (U.S.) (681 LPH) Maximum:...35 GPH (U.S.) (1,30 LPH) Double Model 300 Series: Recommended:...360 GPH (U.S.) (1,363 LPH) Maximum:...650 GPH (U.S.) (,460 LPH) Triple Model 300 Series: Recommended:...540 GPH (U.S.) (,043 LPH) Maximum:...975 GPH (U.S.) (3,690 LPH) Service Parts Elements: 301*...5 Micron Absolute Element 301-W...3 Micron Nominal (9 Absolute) Element 301-30...9 Micron Nominal (40 Absolute) Element 301-CS...Element with Water Absorbing Media...(for use with Hydraulic Recycler) 300-MPG...Maximum Performance Glass Element...(for use with Hydraulic Recycler) Gaskets: 00-GK...Complete Gasket Kit (See Accessories Page) Kits: 00-DEPR KIT...Depressurizer Kit (See Accessories Page) Form 430: Installation, Operation, Parts & Service Information Form 413: Marine Installation, Operation, Parts & Service Information 10 U.L. Listed. Meets U.S. Coast Guard Requirements for Marine Applications. * Standard with Unit Unless Stated.

300 Series Diesel Fuel Filter/Water Separators Cont d. Accessories All Inlet & Outlet Fittings Require O-Ring Seals Aluminum Bowl...00-1AL Clear Bowl w/water Sensor Probes...00-1BP Clear Bowl w/heater Probes...00-1H Clear Bowl w/water Sensor & Heater Probes...00-1HBP Clear Bowl w/marine Collar for Marine Units...00-1M Fittings...See DAHL Fittings Chart Heat Deflector Shield for Marine Units...85-DS Heater Kit...See Accessories Page (Heater Kits & Heater Parts) Shock Pad Mounting Kit...86-SK Water Sensor Warning Light Kit (Use with 00-1BP) 4 Volt DC...4-WLK 300 Series Single Units 300 Diesel Fuel Filter/Water Separator 300-H Diesel Fuel Filter/Water Separator with In-Filter Heater Operates on either 1 or 4 Volt systems. (10 Micron Element) 300-M Marine Diesel Fuel Filter/Water Separator U.L. Listed. Meets U.S. Coast Guard requirements. 300-W30 Diesel Fuel Filter/Water Separator (9 Micron Nominal (40 Absolute) Element) 300 Series Double Manifold Units 300-MFV Two Diesel Fuel Filter/Water Separators Manifolded with Shut-Off Valves Allows continuous operation while servicing. 300-MMV Two Marine Diesel Fuel Filter/Water Separators Manifolded with Shut-Off Valves Allows continuous operation while servicing. U.L. Listed. Meets U.S. Coast Guard requirements. 300 Series Triple Manifold Units 300-MFV3 Three Diesel Fuel Filter/Water Separators Manifolded with Shut-Off Valves Allows continuous operation while servicing. 300-MMV3 Three Marine Diesel Fuel Filter/Water Separators Manifolded with Shut-Off Valves Allows continuous operation while servicing. U.L. Listed. Meets U.S. Coast Guard requirements. Used On 1 & 16 Cylinder Cummins & Detroit Diesel Engines Caterpillar Engines (800 HP & Up) EMD & Alco Engine up to,000 HP + + 4.0 in. (101.6 mm) Marine { Aluminum Mounting Hole Pattern Clearance for 3/8 In. Diameter Fasteners T-Bolt Nylon Gasket (Incl. in 00-GK) Upper T-Bolt Seal (Incl. in 00-GK) Lower T-Bolt Seal (Incl. in 00-GK) 00-31 Primer Plug Primer Plug O-Ring (Incl. in 00-GK) Lid Cover Lid Cover Gasket (Incl. in 00-GK) Centerpipe O-Ring (Incl. in 00-GK) 301*,-W,-30, Element w/gasket -MPG,-CS Centerpipe Body Ejector Spring (4 required) Ejector Spring Clip (4 required) Reverse Flow Gasket (Incl. in 00-DEPR KIT) Reverse Flow Washer (Incl. in 00-DEPR KIT & 00-GK) Reverse Flow Ball (Incl. in 00-DEPR KIT) Bowl Gasket (Incl. in 00-GK) Depressurizer Set (Incl. in 00-DEPR KIT) 00-1 Bowl Bowl Ring Socket Head Bolt 1/4-0 x 5/8 (8 required) O-Ring (Incl. in 00-GK) 100-9 Bowl Plug 100-30 Draincock (1/4 In.) 00-1M Marine Bowl Bowl Ring Socket Head Bolt 1/4-0 x 5/8 (8 required) O-Ring (Incl. in 00-GK) 85-DS Heat Deflector Shield 100-9 Bowl Plug Brass Pipe Plug (1/4 In.) 00-1AL Locomotives Large Stationary Engines Large Boats & Generators Applications Requiring a # 1 Fuel Line Aluminum Bowl Bowl Ring Socket Head Bolt 1/4-0 x 5/8 (8 required) Brass Pipe Plug (1/4 In.) * Standard with Unit Unless Stated. U.L. Listed. Meets U.S. Coast Guard Requirements for Marine Applications. 11

500 Series Tank Diesel Fuel Filter/Water Separator 500 Series Single Units 500 Diesel Fuel Filter/Water Separator 500-BP Diesel Fuel Filter/Water Separator with Water Sensor Warning Light Kit Equipped with a 110 Volt Electrical Connector. MODEL 500-BP Diesel Fuel Filter/Water Separator Designed primarily for large marine engines, storage facilities, island fuel pumps and other permanent installations. Nearly 17,000 square inches (11 square meters) of filtering surface is provided by seven giant DAHL 501-W (10 Micron) elements. Because of the effective separation of water and dirt, the elements will give long service. Specifications Flow Resistance:...1.0 In. Mercury Maximum Working Pressure:...15 PSI (103 kpa) Temperature Range:...-60 to +50 F (-50 to +11 C) Port Thread:... In. NPT Height:...47 In. (1,194 mm) Width:...8 1/ In. (74 mm) Depth:... In. (559 mm) Element Removal Clearance:...10 In. (54 mm) Sump Capacity:...11 U.S. Gallons (41.6 Liters) Flow Rates Single Model 500 Series: Recommended:...1,800 GPH (U.S.) (6,813 LPH) Maximum:...1,90 GPH (U.S.) (7,68 LPH) Double Model 500 Series: Recommended:...3,600 GPH (U.S.) (13,66 LPH) Maximum:...3,840 GPH (U.S.) (14,536 LPH) Multiple Units: Multiply Flow Rate and Sump Capacity by Number of Units Service Parts Elements: 501...4 Micron Nominal (0 Absolute) Element 501-W*...5 Micron Nominal (5 Absolute) Element 501-30...9 Micron Nominal (40 Absolute) Element Gaskets:...See Illustration Form 4500: Installation, Operation, Parts & Service Information Used On Large Marine Diesel Engines Storage Facilities Fuel Storage Tank Pumps Large Stationary Engines Large Capacity Requirements 500-BP Diesel Fuel Filter/Water Separator with Water Sensor Warning Light Kit Equipped with a 0 Volt Electrical Connector. (For Overseas Operation) 500 Series Double Manifold Units 500-MFVBP Double Manifold Diesel Fuel Filter/Water Separator with Shut-Off Valves Allows for continuous operation and Water Sensor Warning Light Kit Equipped with a 0 Volt Electrical Connector. (For Overseas Operation) Features of 500-BP Unit Easy draining with convenient bleed and drain valves. Easy to service - simply remove the 0 inch seal clamp to remove the top lid assembly for element replacement. Easy priming because primer plug is at the top. Easy to clean - handy four inch clean-out hole. Ruggedly built of high quality heavy-gauge steel. Hand welded and pressure tested. Minimum mechanical flow resistance because of the streamlined fuel flow through the seven large centertubes. Troubleshooting vacuum/pressure gauges monitor inlet and outlet ports. The water sensor kit on the 500-BP alerts the operator by a light when the unit should be drained. { Primer Plug (1 In.) 100-30 Air Bleed Valve 500-15 O.D. O-Ring (0 In.) 500-1 Seal Clamp (0 In.) Replacement Light Bulb 501,-W*,-30 Elements (7 required) 85-P Vacuum Gauge/ 85-V Pressure Gauge ( required) Water Sensor Probe Clean-Out Plug (4 In.) 1 * Standard with Unit Unless Stated.

DAHL Hydraulic Recyclers The DAHL Hydraulic Recyclers are specifically designed to remove emulsified water from hydraulic oils. Since water emulsified in hydraulic oil is not removed by the normal DAHL coalescing action, Baldwin has designed a special filter element that absorbs water that has been emulsified in oil. The water remains in the filter element until the element is disposed. As the element absorbs water, the filtering media expands, increasing the restriction in the filter. By monitoring the pressure differential of the element, it is possible to determine when the element is saturated. Two unique DAHL elements have been developed in conjunction with the hydraulic units. The first element is the 301-CS. The 301-CS contains a special polymer enhanced media that absorbs water regardless of emulsification. The element has the capacity to absorb over 1 1/ quarts of water. (This is dependent upon oil viscosity, temperature and other factors.) When the element becomes saturated, the water is disposed along with the element. The second element is the 301-MPG. This has a synthetic grade media that is designed as a fine clean-up element. It has a Beta ratio of at 3 micron and 100 at 1 micron, making this element an excellent choice for most hydraulic clean-up applications. Baldwin has designed two portable clean-up carts based on these hydraulic elements. The 300-DHRAP5 is designed for applications requiring larger quantities of water removal with less concern about contaminant removal. The 300-DHRAS5 is a two stage unit with one absorbing element and one clean-up element. To allow effective removal of emulsified water, these units are best used in multiple-pass applications. 300-DHRAP5 Hydraulic Recycler Portable Unit DAHL 300-DHRAP5: Two DAHL 300 units mounted on a convenient dolly. The units are in a parallel arrangement using two of the special water absorbing elements (301-CS). A 5 GPM pump is furnished with the unit. The flow rate for this unit is dependent on the viscosity of the oil, but has been tested at about 00 gallons per hour initially with 0W SAE oil at room temperature. The flow rate will drop off as the element absorbs water. Included with the unit is a vacuum gauge that aids in monitoring the saturation of the filter. An automatic vacuum switch shuts the pump off at a predetermined vacuum setting to prevent pump and motor damage. Element water capacity is about 3 quarts. 300-DHRAS5 Hydraulic Recycler Portable Unit DAHL 300-DHRAS5: Two DAHL 300 units mounted on a convenient dolly. The units are connected in a series flow arrangement. The hydraulic oil flows through the first unit where Baldwin's special water absorbing element (301-CS) absorbs the emulsified water. The hydraulic oil next flows to a second DAHL unit where the 301-MPG synthetic media element filters contaminants out of the oil. This unit is furnished with a 3 GPM pump. Two vacuum gauges monitor the pressure drop across both filters. An automatic vacuum switch shuts the pump off at a predetermined vacuum setting. Element water capacity is about 1 1/ quarts. 13

Accessories Heater Kits & Heater Parts Diesel fuel can become a problem in cold weather. Wax forms, plugging fuel lines and filters. DAHL has models 100-H and 150-H diesel fuel filter/water separators with the 55-EK Heater Kit included and models 00-H and 300-H with the 85-EK Heater Kit included. Or you can retrofit DAHL 100 and 150 series diesel fuel filter/water separators with the 55-EK Heater Kit. DAHL 00 and 300 series diesel fuel filter/water separators can be retrofitted with the 85-EK Heater Kit. Both sizes feature an electric heating element between the body and the filter element. This simultaneously heats the filter element and the fuel around it. An illuminated toggle switch conveniently located in the operator s area makes it easy to turn on and off. The unit is simple to install and operate. No seasonal adjustment or other maintenance is needed. Operates on 1 or 4 Volt Systems (Negative or Positive Ground) Low Amperage Requirements (Only 10 Amps at -40 F) Heats Fuel & Element In-Filter Heater Kits Use 55-EK for DAHL 100 or 150 Series and 85-EK (shown) for DAHL 00 or 300 Series 55-EK 85-EK Numbers Description & (Quantity) Numbers Heater Element (1) 100-1H Heater Probes in Clear Bowl (1) 00-1H Bowl Gasket (1) Toggle Switch & Connectors Instructions 55-EK has Replaced the 45-EK Sensors 4-WLK Dash-Mounted Water Sensor 4 Volt Warning Light Kit DAHL Literature All printed materials are listed here as individual items. Form 4005 DAHL Catalog Form 4005-S DAHL Catalog (Spanish) Form 4011 DAHL 55-EK and 85-EK In-Filter Heater Kit Installation Instructions Form 401 Recycler, Recycler/Blender & Fuel Transfer Models - Installation, Operation, Parts & Service Information Form 4013 DAHL 140-50 Hand Primer Kit Form 405 Model 150 - Installation, Operation, Parts & Service Information Form 4060 Form 4100 Form 413 Form 430 Form 4500 Model 65 & 75 - Installation, Operation, Parts & Service Information Model 100 - Installation, Operation, Parts & Service Information Marine - Installation, Operation, Parts & Service Information Model 00 & 300 - Installation, Operation, Parts & Service Information Model 500 - Installation, Operation, Parts & Service Information 14 There is no association or affiliation between Baldwin Filters and Racor. Racor is a registered trademark and division of Parker Hannifin Corp.

Accessories (Cont d.) Vacuum Gauges Vacuum gauge indicates the remaining life in filter elements. Replacement of the filter should be made when the gauge reading is -6 inches greater than the new element reading. (The exact reading depends on the characteristics of the fuel system, such as the engine, normal flow rate, component height, fuel line size, etc.) To accurately determine when to replace the element, a reading of the gauge should be taken at the first noticeable power loss of the engine. Reduce this gauge reading by 1 inch of mercury for reference of future filter servicing. The gauge is designed to be connected to the outlet side of the DAHL filter unit and can be mounted directly on the unit or dashmounted. 85-V Vacuum Gauge 85-P Pressure Gauge Draincocks 60-30 1/4 In. Draincock (See Model 65) 100-30 1/4 In. Draincock 00-30U 1/4 In. U.L. Approved Draincock Depressurizer Kits 100-DEPR KIT Includes Depressurizer Set, Reverse Flow Gasket, Reverse Flow Washer and Reverse Flow Ball for 100 Series and 150 Series 00-DEPR KIT Includes Depressurizer Set, Reverse Flow Gasket, Reverse Flow Washer and Reverse Flow Ball for 00 Series and 300 Series Mounting Bracket Kit 100-MNTG KIT Includes Mounting Bracket, [] Bracket Bolts, [] Washers and [] Nuts for 100 Series Gasket Kits 60-GK 100-GK 150-GK Gaskets for 60, 65 & 75 Models includes Bowl Gasket, Bowl O-Ring, Hub Assembly Gasket and Primer Plug O-Ring Gaskets for 100 Series includes Bowl Gasket, [] Bowl Plug Gaskets (older models), Centerpipe O-Ring, Lid Cover Gasket, Primer Plug O-Ring, Reverse Flow Gasket and Reverse Flow Washer Gaskets for 150 Series includes Bowl Gasket, [] Bowl Plug Gaskets (older models), [] Bowl Plug O-Rings, Centerpipe O-Ring, Lid Cover Gasket, Lid O-Ring, Primer Plug O-Ring, Reverse Flow Gasket, Reverse Flow Washer and T-Bolt O-Ring 00-GK Gaskets for 00 & 300 Series includes Bowl Gasket, [] Bowl Plug Gaskets (older models), Bowl Plug O-Ring, Centerpipe O-Ring, Lid Cover Gasket, Lower T-Bolt Seal, Nylon Gasket, [] Primer Plug O-Rings, Reverse Flow Gasket, Reverse Flow Washer and T-Bolt O-Ring Hand Primer For DAHL Models 65, 75 & 100 140-50 KIT 3/8 In. Fuel Hose The DAHL primer is designed to make draining and/or element changing easy. Kit includes primer bulb and hose clamps. Marine Shield & Shock Pad Kits 185-DS 85-DS 186-SK Aluminum Heat Deflector Shield for 100 & 150 Series Aluminum Heat Deflector Shield for 00 & 300 Series Mounting Bracket Shock Pad Kit for 100 Series 86-SK Mounting Bracket Shock Pad Kit for 150, 00 & 300 Series 15

DAHL Fittings Chart 90 Elbow Straight Thread with O-Ring/37 Male JIC 90 Elbow Straight Thread 1 with O-Ring/37 Male JIC Drilled & Tapped for #4 Vacuum Gauge Hose 37 Male JIC Straight Thread with O-Ring 37 Female JIC Swivel-Push-On Hose Fitting Female Pipe Straight Thread with O-Ring FITTING FOR DAHL UNIT THREAD 1 THREAD 90 Swivel Elbow Straight Thread with O-Ring/37 Female JIC 90 Swivel Elbow Straight Thread with O-Ring/37 Female JIC Drilled & Tapped for #4 Vacuum Gauge Hose 1 1 1 1 65, 75 & 100 Series 9/16-18 UNF 7/16-0 65, 75 & 100 Series 9/16-18 UNF 9/16-18 150 & 00 Series 7/8-14 UNF 3/4-16 150 & 00 Series 7/8-14 UNF 7/8-14 300 Series 1 1/16-1 UNF 7/8-14 300 Series 1 1/16-1 UNF 1 1/16-1 65, 75 & 100 Series 9/16-18 UNF 7/16-0 65, 75 & 100 Series 9/16-18 UNF 9/16-18 65, 75 & 100 Series 9/16-18 UNF 9/16-18 150 & 00 Series 7/8-14 UNF 3/4-16 150 & 00 Series 7/8-14 UNF 3/4-16 150 & 00 Series 7/8-14 UNF 3/4-16 150 & 00 Series 7/8-14 UNF 3/4-16 150 & 00 Series 7/8-14 UNF 7/8-14 300 Series 1 1/16-1 UNF 7/8-14 300 Series 1 1/16-1 UNF 1 1/16-1 65, 75 & 100 Series 9/16-18 UNF 7/16-0 65, 75 & 100 Series 9/16-18 UNF 9/16-18 150 & 00 Series 7/8-14 UNF 3/4-16 150 & 00 Series 7/8-14 UNF 7/8-14 300 Series 1 1/16-1 UNF 7/8-14 300 Series 1 1/16-1 UNF 1 1/16-1 65, 75 & 100 Series 7/16-0 1/4 Hose 150 & 00 Series 3/4-16 1/ Hose 150, 00 & 300 Series 7/8-14 5/8 Hose 300 Series 1 1/16-1 3/4 Hose 65, 75 & 100 Series 9/16-18 UNF 1/4-18 NPT 65, 75 & 100 Series 9/16-18 UNF 3/8-18 NPT 150 & 00 Series 7/8-14 UNF 3/8-18 NPT 150 & 00 Series 7/8-14 UNF 1/-14 NPT 150 & 00 Series 7/8-14 UNF 3/4-14 NPT 300 Series 1 1/16-1 UNF 1/-14 NPT 300 Series 1 1/16-1 UNF 3/4-14 NPT 300 Series 1 1/16-1 UNF 3/4-14 150 & 00 Series 7/8-14 UNF 1/-14 16

Replacement Parts Filter Bowls Filter Elements 60-1A Amber Bowl for 60 & 65 Series Draincock included. 75-1 Aluminum Bowl for 75 Series 100-1 Clear Replacement Bowl for 100 & 150 Series 100-1AL Aluminum Replacement Bowl for 100 & 150 Series 100-1BP Clear Bowl w/water Sensor Probes for 100 & 150 Series 100-1H Clear Bowl w/heater Probes for 100 & 150 Series (Part of 55-EK Heater Kit) 100-1M Clear Bowl w/marine Collar for 100 & 150 Series Marine Units 00-1 Clear Replacement Bowl for 00 & 300 Series 00-1AL Aluminum Replacement Bowl for 00 & 300 Series 00-1BP Clear Bowl w/water Sensor Probes for 00 & 300 Series 00-1H Clear Bowl w/heater Probes for 00 & 300 Series (Part of 85-EK Heater Kit) 00-1HBP Clear Bowl w/water Sensor and Heater Probes for 00 & 300 Series (Upper Holes for Heater, Lower Holes for Bowl Probes) 00-1M Clear Bowl w/marine Collar for 00 & 300 Series Marine Units DAHL Equivalents For Racor Assemblies Racor Racor Flow DAHL Flow DAHL Assembly (Max.) (Max.) Assembly 00FG 15 30 65 00FGM 15 30 75 500FG 60 65 100 500MA 60 65 100-M 900FG 90 100 150 900MA 90 100 150-M 1000FG 180 00 00 1000MA 180 00 00-M 73/1000FG 360 400 00-MFV* 73/1000MA 360 400 00-MMV* 75/1000FG 360 400 00-MFV* 75/1000M 360 400 00-MMV* 79/1000FG 540 650 300-MFV3* 79/1000MA 540 650 300-MMV* * Unit includes shut-off valves. As with all filter elements made by Baldwin, you can be sure that DAHL filter elements are made just right. Not only do we make sure the paper conforms to our exacting requirements, but we also use more paper in a given size filter if this is needed to do the job. (The 10 micron elements are designed for winter or severe conditions.) 61 Micron Filter Element for DAHL 60 Series 61-W 10 Micron Filter Element for DAHL 60 Series 66 Micron Filter Element for DAHL 65 & 75 Series 66-W 10 Micron Filter Element for DAHL 65 & 75 Series 66-30 30 Micron Filter Element for DAHL 65 & 75 Series 101 Micron Filter Element for DAHL 100 Series 101-W 10 Micron Filter Element for DAHL 100 Series 101-30 30 Micron Filter Element for DAHL 100 Series 151 Micron Filter Element for DAHL 150 Series 151-W 10 Micron Filter Element for DAHL 150 Series 151-30 30 Micron Filter Element for DAHL 150 Series 01 Micron Filter Element for DAHL 00 Series 01-W 10 Micron Filter Element for DAHL 00 Series 01-30 30 Micron Filter Element for DAHL 00 Series 301 Micron Filter Element for DAHL 300 Series 301-W 10 Micron Filter Element for DAHL 300 Series 301-30 30 Micron Filter Element for DAHL 300 Series 301-CS Water Absorbing Element for DAHL 300 Series 301-MPG High Performance Glass Media for DAHL 300 Series 501 Micron Filter Element for DAHL 500 Series 501-W 10 Micron Filter Element for DAHL 500 Series 501-30 30 Micron Filter Element for DAHL 500 Series (See Product Guide for filter element specifications) Replacements For Racor Elements Racor Racor Baldwin Element Housing Element 00 Series 000SM-OR...PF599 000TM-OR...PF599-10 000PM-OR...PF599-30 500FG Series 010SM-OR...PF598 010TM-OR...PF598-10 010PM-OR...PF598-30 900FG Series 040SM-OR...PF7889 040TM-OR...PF7889-10 040PM-OR...PF7889-30 1000FG Series 00SM-OR...PF7890 00TM-OR...PF7890-10 00PM-OR...PF7890-30 There is no association or affiliation between Baldwin Filters and Racor. Racor is a registered trademark and division of Parker Hannifin Corp. 17

MARINE INSTALLATION A. FILTER MOUNTED ABOVE FUEL STORAGE TANK 1. Select a location in the fuel line between the fuel tank and the fuel pump, ahead of the vacuum side filters. All secondary or pressure side filters located between the pump and the engine should be serviced and left in place.. Mount the DAHL unit vertically on the vacuum (suction) side of all fuel pumps in a convenient location for servicing and inspection of contaminants in the bowl. Locate the height of the unit between the bottom of the fuel tank and the inlet of the fuel pump if possible. See Figure 1. Install furnished shock pads as indicated in Figure 3. Engine Fuel Pump Factory Primary Filter (if applicable) FIGURE 1 Outlet Inlet Fuel Tank NOTE: Allow 1/ inches (1 1/ for 100-M) vertical clearance below the unit for servicing the element and draining the contaminants. 3. Install the fuel line from the fuel tank to the DAHL filter INLET using appropriate non-galvanized fittings. See DAHL Fittings Chart on Page 4. 4. Install the fuel line from the DAHL filter OUTLET to the INLET of the transfer or fuel pump. NOTE: To obtain maximum element life, remove as much mechanical restriction as possible from the system by doing the following: a. Remove the primary filter (if this does not affect warranty). b. Use the largest diameter fuel line that is practical. c. Mount the unit as near to the level of the pump as possible. d. Eliminate sharp bends in the fuel lines wherever possible. The best indicator of a fuel element s condition is a vacuum gauge. (See 85-VK Series in the Baldwin Product Guide catalog.) A tapped fitting is recommended for mounting the gauge on the OUTLET port of the DAHL filter unit. (Manifold units are already tapped and plugged.) Remove the 1/8 inch plug and install the vacuum gauge there. Fittings and gauges are available from your dealer or contact Baldwin Filters. Prime the filter as indicated under ELEMENT REPLACEMENT section. B. FILTER MOUNTED BELOW FUEL STORAGE TANK FIGURE 3 Installation procedures are the same as above plus an addition to Step 3: A ball- or butterfly-type shut-off valve must be installed ahead of the DAHL unit INLET. See Figure. This valve is necessary to shut off the fuel when changing the element. Valves are available from your dealer. NOTE: Valve not required when installing DAHL valved manifold units. FIGURE Mounting Hardware Sequence (00-M Shown) NOTE: Fasteners Not Supplied with Unit Vacuum Gauge Installation FIGURE 4 If it is ever necessary to dismantle the unit for inspection and/or possible repairs, refer to the parts illustration. Then follow these simple steps: 1. Refer to ELEMENT REPLACEMENT section for disassembly. (Dismount if desired.). Remove the socket head bolts from the bowl ring to release the bowl. Stubborn bolts are easily removed by shocking the head. Place the allen wrench into the bolt and lightly rap the wrench with a hammer. Remove the bolt. 3. Unscrew the depressurizer cone to inspect the reverse flow valve. Caution: Cone edges are sharp. Use gloves or a rag REBUILD PROCEDURE 100-M 150-M/00-M/300-M All Manifold Units for protection. 4. Check all parts for damage. Replace all damaged parts or hard gaskets. (Order Gasket Kit 100-GK, 150-GK or 00-GK, as appropriate.) 5. Refer to the parts illustration for reassembly. Clean all gasket grooves and contact surfaces of foreign matter. Coat the lid cover and bowl gaskets with grease and all other gaskets and O-Rings with oil. Hand tighten the depressurizer cone and wrench tighten the socket head bolts. 6. Again, refer to ELEMENT REPLACEMENT section to finish reassembly.

NOTE: The bowl should always be drained before water or contaminant levels reach the bottom of the depressurizer cone. Check daily with the engine off. A. DAHL Units Mounted HIGHER Than Fuel Storage Tank 1. Turn engine off.. Vent the DAHL filter to allow draining as follows: (a) On DAHL Model 100-M without a primer bulb, loosen the outlet port swivel fitting connection. Remove the pipe plug and drain all contaminants. (b) On DAHL Models 75 & 100-M with a primer bulb, remove the pipe plug and squeeze the primer bulb to evacuate all contaminants. MARINE SERVICING DRAINING WATER A. When To Replace As a general guideline, depending on fuel quality and engine use, elements should be replaced as follows: 1. DAHL 75 and DAHL 100 & 150 series, 500 hours or 0,000 miles. DAHL 00 & 300 series, 1000 hours or 40,000 miles. If you have a vacuum gauge, the first replacement should be made at the very first indication of power loss at high RPMs. Make a note of the vacuum gauge reading at this point. The differences in various fuel system requirements make it impossible to predict what this reading will be. Mark the reading on the gauge dial or the unit for future element replacement. B. How To Replace Contaminated Element 1. Follow directions for Draining Water. Drain all water and sufficient fuel for easy handling of the filter body.. Loosen the lid clamp knobs on 100-M series or the T-Bolt handle on 150, 00 & 300 series to release the filter body from the lid. (It is not necessary to completely remove the seal clamp or T-Bolt from the DAHL filter lids.) Support the filter body with your hand prior to release. 3. Remove the element with a turning motion. At this point, you may clean the outside of the filter body. Use only clean diesel fuel or kerosene and wipe clean. 4. Inspect the ejector spring(s) at the bottom of the body. Also check the centerpipe O-Ring and replace if hard or damaged. 5. Remove and replace the lid cover gasket. Be sure the lid groove and body lip are clean. (Grease lid gasket before positioning.) TROUBLESHOOTING Engine starting and power loss problems from the fuel system are usually caused by one or more of the following: A. Air Leaks 1. Fittings. Insure O-Rings on fittings in DAHL filter ports are lubricated and not damaged, cracked or dirty. NOTE: When using JIC 37 fittings, be sure only mating JIC 37 fittings are used. Misalignment will occur and air leakage will result from an attempt to fasten a 45 fitting to a JIC 37 fitting. Check for fitting looseness, seat dents, misalignment or unmatched threads. All fittings must be wrench tight.. Bubbles In The Bowl. If bubbles appear at the depressurizer cone, a leak is indicated between the fuel tank and the inlet port. NOTE: Old fuel lines (rubber hose or metal tubing) may crack when moved. Check areas around push-on fittings, pipe adapters, hose clamps, etc. If air bubbles appear at the pipe plug, check for particles stuck in the valve seat or a partly open pipe plug. Also check for defective, miscentered or unlubricated bowl gaskets. Check bowl plug O-Ring to to make sure it is not cracked to extruded out of place. The bowl plug shoud be hand tightened only. 3. Gaskets. If the lid or bowl has been removed, make sure the gasket grooves are clean. Inspect gaskets for proper seating in the grooves. Lubricate gasket(s) with oil or grease. NOTE: On DAHL Model 100-M, the arrow on the lid clamp must point up (large lip on top). Be sure the lid and body lips are inside the clamp lips for a complete seal. Knob must be hand tight. (c) On DAHL 150, 00 & 300 series, open the primer plug. Remove the pipe plug and drain all contaminants. 3. Replace the pipe plug and follow the priming instructions shown below. B. DAHL Units Mounted LOWER Than Fuel Storage Tank 1. Turn engine off and close shut-off valve. (Valved Manifold units may be drained and elements replaced with the engine running at idle. Close inlet and outlet valves to isolate the filter being serviced.). Remove the pipe plug and drain all contaminants. 3. Replace the pipe plug and follow the priming instructions shown below. ELEMENT REPLACEMENT C. Reassembly 1. Lubricate the top and bottom element gaskets. Install the element onto the centerpipe with a turning motion.. Fill the filter body with clean diesel fuel to within one inch of the top. 3. Double check the lid cover gasket position in the lid groove. 4. Attach the body to the lid and hand tighten the lid clamp knob or the T-Bolt handle. NOTE: On DAHL Model 100-M, check the entire circumference of the body and lid for proper clamp alignment. (Clamp must be oriented with the knob to the right. See up arrow on band for correct orientation.) D. Priming 1. Eliminate air use existing fuel system primer, if so equipped. (a) On DAHL Model 100-M with a primer bulb, loosen the outlet port swivel fitting connection and squeeze the bulb repeatedly until diesel fuel appears at swivel. Then tighten swivel fitting. (b) If there is no primer bulb on a DAHL 100-M, remove the inlet port elbow fitting and fill to the top with clean diesel fuel. (Or, if you can pivot the unit upside down, prime it through the bowl plug.) (c) On DAHL 150, 00 & 300 series, remove the primer plug and fill to the top with clean diesel fuel. NOTE: Clean the heat deflector shield to remove any accumulated diesel fuel.. Start engine and check for leaks. B. Clogging and Restriction 1. Fuel Lines. Check for collapsed lines caused by sharp bends or excessive turns. Check tank and/or filter shut-off valve(s).. Filter Elements. Early clogging can occur from badly contaminated fuel (micro-organism growth, rust, sludge, dirt, etc.) Always carry a spare DAHL element. Asphaltinic materials (fuel oxidation products), which are normally harmless to the injection system, can eventually plug original equipment filters remaining in the fuel system. If problems persist after the DAHL element has been replaced, also replace the other fuel filter elements. 3. Filter Inlet. Severely contaminated fuel may cause inlet plugging. In this event, close the fuel tank supply shut-off valve (if equipped) and disconnect the inlet line. Remove the bowl and clean the inlet. Should the depressurizer cone also be plugged, disassemble and clean out. 4. Bleed Back. If fuel in the DAHL filter bleeds back to the fuel tank, an air leak or reverse flow valve problem is indicated. Inspect fuel lines and fittings first as indicated above. If the reverse flow valve is clogged, use air or clean fuel to flush out. C. Malfunction of Engine Parts Pre-existing conditions in pumps and injectors can also cause power loss and engine starting problems. See your equipment dealer if the above troubleshooting guides do not cover your problem. 3