material HaNDlINg CompaCt Catalogue

MATERIal HANDLING Compact catalogue

A matter of trust. Paul, 46, Chief engineer POLYURETHANE TIMING BELTS optibelt polyurethane timing belts convince due to their impressive product features. They set standards regarding strength, elongation and wear. The thermal and chemical capacity is exceptional. It is good to know that these benefits are combined with a competent technical service. First class products for flexible drive solutions and conveyance challenges Optibelt is capable of implementing even the most challenging requirements economically. Professionalism you can also benefit from.

POWER TRANSMISSION DRIVES 5 MECHANICAL belt joints 28 LINEAR DRIVES 9 ROUND BELTS 30 CONVEYOR DRIVES 11 TIMING BELT PULLEYS 32 POWER TRANSMISSION DRIVES ALPHA Power LINEAR DRIVES ALPHA flex ALPHA linear CONVEYOR DRIVES ALPHA V ALPHA TORQUE ALPHA Special ALPHA SRP endless open-ended endless welded / endless APPLICATION EXAMPLES Machine tools Positioning drives Parallel conveyors Textile machines Lifting drives Synchronous conveyors Printing machines Handling devices Inclined conveyors Packaging machines Door and gate opening drives Accumulating conveyors Office machines Washing bays Vacuum conveyors Medical devices Plotters Take-up and transfer units Robots Packaging machines Separators Handling devices Gantry robots Workpiece positioners

4 Belt product range optibelt ALPHA Belt product range PRODUCT GROUPS ALPHA TORQUE ALPHA Power ALPHA SRP Casted, endless ALPHA flex ALPHA linear ALPHA V Extruded, endless Extruded, open-ended Welded, endless BASIC PROFILES Profile, imperial MXL, XL, L (ALPHA TORQUE) PROFILE H XL, L, H, XH XL, L, H, XH Profile T T2.5, T5, T10, T20 DT5, DT10 T5, T10, T20, DT5, DT10 T5, T10, T20 T5, T10, T20, DT5 1, DT10 1 Profile TK, wedge T5K6, T10K6, T10K13 Profile AT AT5, AT10 AT5, AT10, AT20, DAT5, DAT10 Profile ATK, wedge Profile ATL AT5, AT10, AT20 ATL5, ATL10, ATL20 AT5, AT10, AT20, DAT5 1, DAT10 1 AT5K6, AT10K6, AT10K13 Profile ATC, cleat ATC10 Profile HTD 5M, 8M, 14M, D5M, D8M 5M, 8M, 14M, 14ML 5M, 8M, 14M, 14ML D5M 1, D8M 1 Profile F, flat belts F2, F2.5, F3, FL3 F2, F2.5, F3, FL3 Steel Standard tension Steel Steel cord 2 Steel, high flexible Aramid excluding AT20, 14M, XH, F2.5, F3 Steel, high flexible, excluding imperial profiles, T5, ATL10, AT20, F2.5, F3 Stainless steel excluding L, 5M, 14M, T5, AT5, ATL10, AT20, F2.5, F3 Special tension cords Optionally without coiling sleeve Aramid Steel, high flexible Stainless steel Polyester Aramid Stainless steel On request + 3 1 Double toothed profiles on request 2 and without the according profiles TK, ATK 3 Profile T10 available without coiling sleeve, further profiles on request

POWER TRANSMISSION DRIVES

6 power transmission drives optibelt ALPHA TORQUE for power transmission drives Profiles MXL, XL, L, T2.5, T5, T10, T20 Endless, casted ALPHA TORQUE polyurethane timing belts have the following characteristics: Nominal sleeve height up to 380 mm Belt lengths up to 2250 mm DT2.5, DT5, DT10 Free choice of colour on request Position of the length tolerance field is definable, e. g. for fixed center distances Available profiles single-sided tooth: AT5, AT10, T2.5, T5, T10; T20, MXL, XL, L Double-sided tooth available for profiles DT2.5, DT5; DT10 AT5, AT10 Tension members: steel, high flexible steel, aramid, stainless steel, polyester, Vectran Casting process for alpha power and ALPHA TORQUE timing belts

power transmission drives 7 optibelt ALPHA Power For high performance power transmission drives Profiles Endless, casted alpha power polyurethane timing belts have the following characteristics: optimised properties of the ALPHA Power offer up to 30 % higher power ratings T2.5, T5, T10, T20 Available profiles single-sided tooth: AT5, AT10, T2.5, T5, T10; T20 Double-sided tooth available for profiles DT2.5, DT5; DT10 DT2.5, DT5, DT10 High indexing precision and narrow tolerances Strong adhesion between polyurethane and tension cord Position of the length tolerance field is definable, e. g. for fixed center distances Tension members: steel, high flexible steel, stainless steel AT5, AT10 Casting process for alpha power and ALPHA TORQUE timing belts

8 power transmission drives optibelt ALPHA flex for power transmission drives Profile H, T5, T10, T20 Endless, extruded alpha flex polyurethane timing belts have the following characteristics: length range from approx. 1500 mm to 24,000 mm DT5, DT10 Belt can be produced in every pitch step within length range Production widths 100 mm or 150 mm Optional with polyamide fabric on the teeth Direct weld on of cleats and guides possible AT5, AT10, AT20 Optional design includes high flexible or stainless steel tension members Dual cord with S+Z winding of the tension members for lower tracking force Available in profiles H, T5, T10, T20, AT5, AT10, AT20, 5M, 8M, 14M Double-sided tooth available for DT5, DT10, DAT5, DAT10, D5M, D8M DAT5, DAT10 5M, 8M, 14M D5M, D8M Concept of the alpha flex timing belt with dual (S+Z) tension members and extruded polyurethane

LINEAR DRIVES Arntz Optibelt Group, GerMAny

10 LINEAR DRIVES optibelt ALPHA linear FOR LINEAR DRIVES Profiles XL, L, H, XH, T5, T10, T20 OPEN-ENDED, EXTRUDED ALPHA LINEAR POLYURETHANE TIMING BELTS HAVE THE FOLLOWING CHARACTERISTICS: AT5, AT10, AT20, ATL5, ATL10, ATL20 High tension force with low elongation High positioning accuracy Optional design includes high flexible steel, aramid and stainless steel tension members Timing belts for linear drives in profile ATL Available with polyamide fabric layers on the teeth and / or the belt top surface 5M, 8M, 14M, 14ML PU optionally with FDA / EU approval for direct contact with food Optional with thicker belt back, T2, PU foam yellow and APLplus optional colours available F2, F2.5, F3, FL3 roll lengths 50 m or 100 m, > 100 m available on request Available in profiles XL, L, H, XH, T5, T10, T20, AT5, AT10, AT20, ATL5, ATL10, ATL20, 5M, 8M, 14M, 14ML, F2, F2.5, F3, FL3 Design of the ALPHA LINEAR timing belt with parallel tension cords and extruded polyurethane Arntz Optibelt Group, GerMAny

CONVEYOR DRIVES Arntz Optibelt Group, GerMAny

12 conveyor drives optibelt ALPHA SRP for conveyor drives process of extrusion Casting CHARACTERISTICS OF THE CASTed ALPHA SRP WITH CLEATS: Easy production of small belts with cleats through moulding process Large number of cleats within the narrowest space excellently formed, precisely shaped cleat geometries due to cast polyurethane process reproducible high precision High stability of the cleat on the base belt due to homogeneous compouding alpha srp timing belts with cleats process of centrifugal Casting CHARACTERISTICS OF THE CASTed ALPHA SRP WITH dual layer polyurethane backing: Production of small coated timing belts or flat belts by moulding process Backings without joints Highly stable production process High stability of the adhesion between backing and base belt due to homogeneous compouding The ALPHA SRP is based on the belt designs of the ALPHA Power or ALPHA TORQUE timing belt range. Further designs on request. alpha srp timing belts with dual layer backing

conveyor drives 13 optibelt ALPHA V for conveyor drives Profiles XL, L, H, XH, T5, T10, T20 WELDED ALPHA V POLYURETHANE TIMING BELTS HAVE THE FOLLOWING CHARACTERISTICS: Minimum belt length ranges from 450 mm to 1200 mm belt lengths available in every pitch step AT5, AT10, AT20 Low-priced and quick availability ideal for transport drives Available with polyamide fabric on the teeth and / or on the belt top surface PU optionally with FDA / EU approval for direct contact with food ATC10 Optional with thicker belt back, T2, PU foam yellow and APLplus Strong bonding of cleats and guides Despite discontinuous tension members approx. 50 % shear resistance versus the endless timing belts Available in profiles XL, L, H, XH, T5, T10, T20, AT5, AT10, AT20, 5M, 8M, 14M, 14ML, T5K6, T10K6, T10K13, AT5K6, AT10K6, AT10K13, F2, F2.5, F3, FL3, ATC10 5M, 8M, 14M, 14ML T5K6, T10K6, T10K13 AT5K6, AT10K6, AT10K13 F2, F2.5, F3, FL3 Finger-shaped punched-out belt ends and welded ALPHA V timing belt

14 ALPHA SpeCIal WITH COATINGS WITH MECHANICal PROCESSING WITH CleatS

optibelt ALPHA Special WITH COATINGS l us APLp! New Despite other PVC foils, this coating is applied on the optibelt ALPHA LINEAR directly during the extrusion process; Welding to form ALPHA V in combination with the coating is possible jointless; completely adhesive; easy and costeffective coating for conveyance. TIMING BELTS WITH COATINGS optibelt ALPHA Special are value-added with a coating on the belt top surface and can be mechanically processed. The wide range of coatings and forward machining options combined with the features of the timing belt allow for the development of innovative solutions for transport purposes.

16 conveyor drives Overview coatings, mate CHaracteristics Foam POLYURETHANE (PU) Sylomer R (see picture) Sylomer L Celloflex Sylomer M PU-foam yellow PU 06 RUBBER Porol (see picture) EPDM with profiles or structures Polyurethane (PU) PU longitudinal groove (see picture) Pointed cone PU longitudinal groove fine PU-spike profile Pebbles rounded cone RUBBER Supergrip black (see picture) Supergrip blue Polyvinylchloride (PVC) PVC shark tooth (see upper picture) PVC longitudinal groove Supergrip petrol blue Supergrip green Supergrip white (see picture below) Minigrip petrol blue Minigrip green PVC cleats PVC fishbone pattern PVC saw tooth PVC triangular profile

conveyor drives 17 rial and surface SmootH OR SLIGHtlY STRUCtuRED POLYURETHANE (PU) PU foil 65 Shore A Polythane D15 Polythane D44 PU foil blue PU foil 85 Shore A T2 (see picture) PU foil 92 Shore A Higher back RUBBER RP 400 (see picture) Correx beige Linatex Linaplus FGL NG red Linatrile Elastomer green POLYVINYLCHLORIDE (PVC) PVC foil petrol blue (see picture) PVC foil green PVC foil blue PVC foil white APL plus PVC pepita pa FABRIC PA fabric (see picture) PA fabric anti static Special PTFE (see upper picture) TT60 Para flees Chrome leather (see picture below) Viton

18 conveyor drives optibelt EXTRACT FROM StaNDARD CoatINGS Picture of the coating Name, colour, material Standard thickness s [mm] Hardness / density Temperature resistance Minimum pulley Ø [mm] Slaving capacity Abrasion resistance Sylomer L, green, PU foam s 6.0 12.0 15.0 20.0 25.0 300 kg/m 3 30 C...+70 C Ø 120 240 300 400 500 Slaving Abrasion resistance PU 06, yellow, fine pored PU s 2.0 3.0 4.0 5.0 6.0 8.0 55 Shore A 10 C...+60 C Ø 60 70 80 100 120 160 Slaving Abrasion resistance PU foil 85 shore a, transparent, PU s 2.0 3.0 4.0 85 Shore A 10 C...+70 C Ø 60 80 100 Slaving Abrasion resistance Linatex, red, natural rubber s 1.5 2.4 3.2 5.0 6.4 8.0 38 Shore A 40 C...+70 C Ø 30 50 65 100 140 180 Slaving Abrasion resistance PU longitudinal groove, fine, transparent, PU s 3.5 85 Shore A 10 C...+70 C Ø 70 Slaving Abrasion resistance Supergrip petrol blue, polyvinyl chloride s 4.0 40 Shore A 10 C...+90 C Ø 60 Slaving Abrasion resistance APLplus, red, elastic PVC s 2.0 3.0 65 Shore A 20 C...+100 C Ø 60 80 Slaving Abrasion resistance

conveyor drives 19 optibelt ALPHA Special WITH MECHANICAL PROCESSING Milled shapes MECHANICAL PROCESSING Additional geometrical and dimensional adaptations of standard timing belts, coated belts and belts cleats extend the application options. The following processes are available for forward machining: Carved coating Grinding Milling Water jet cutting Punching Drilling Cutting, Carving Longitudinal groove in the teeth Punched timing belt

20 conveyor drives optibelt ALPHA Special WITH CLEATS TIMING BeltS WITH CleatS Cleats can be additionally applied on ALPHA Linear, AlpHA V and ALPHA flex timing belts via various processes. These include welding, chemical bonding and mechanical connections. The in-house injection moulding process ensures good product availability. In case you cannot find the suitable cleat in our product range, we can produce or adapt it according to your requirements in a cost-effective way. We will be pleased to support you in finding the suitable solution for your transport tasks. Cleats including punched holes with attachments for tool carriers

conveyor drives 21 optibelt ALPHA Special WITH CLEATS Available standard polyurethane cleat materials: PU 92 Shore A, white pu 65 and 85 Shore A, transparent PU 98 Shore A, greyish white In contrast to coatings with frictional connection, cleats allow for a synchronous traction of the goods to be conveyed in conveyor drives. Furthermore, they e. g. convey the goods in longitudinal direction and / or sideways and align them if necessary position goods on the conveyor belt separate the goods allow for high acceleration and / or high speeds synchronise the goods to be conveyed with the belt The Optibelt cleat range offers a great number of cast blanks and cleats which can directly be used for many different applications. In case none of these cleats are suitable, an appropriate cleat can be produced by adapting the present cleat via mechanical processing by producing an appropriate cleat in a customised injection mould The production in a dedicated injection mould is suitable for simple cleat shapes in medium volumes and for more com - plex shapes in small volumes. It can be carried out in the company s own tool shop. pu FDA 85 Shore A, transparent / blue GFK (PU) Further materials and colours available on request Cleats as workpiece carriers Parallel conveyor with supporting table simple Shape and function of the cleat special rectangle round T-shaped L-shaped blades trapezoidal shape V-trapezoidal shape triangle concave, convex groove holes inserts

22 conveyor drives optibelt ALPHA Special CUStomISED SOLUTIONS The processing of PU timing belts is one of our specialities. Due to many years of experience we develop optimum solutions for special applications of our customers in the segments of conveyance, food, packaging, glass, wood, linear drives and medical applications. All product groups of endless and joined belts can be used for conveyance. Examples of applications are: parallel and synchronous conveyors, inclined conveyors, accumulating conveyors, vacuum conveyors, separators or workpiece postioners, exhaust units The base belts which were selected according to the requirements can be adapted to the special type of conveyance if necessary via coatings and /or cleats the base belt, the coating and the cleat can all be additionally adapted in geometry and dimension via mechanical processing. These forward machined special belts are labelled special in addition to their actual product group name. Example: The product group name of an endless welded optibelt ALPHA V polyurethane timing belt with additional coating is changed to optibelt ALPHA V Special. Coated timing belts have the following characteristics: improved chemical resistance, e. g. for applications in food industry High abrasion resistance, e. g. accumulation conveyors High temperature resistance, e. g. for the conveyance of heat treated parts Good cut resistance, e. g. for sharp-edged goods to be conveyed Non-stick, e. g. for contact with adhesives Antistatic, e. g. for the conveyance of electronic parts Absorption of shocks, e. g. when placing sensitive goods

conveyor drives 23 optibelt ALPHA Special APPLICatION EXAMPLES Picture 1: Customised solution for the conveyance of semi-finished goods The example given in picture 1 presents a customised solution for the conveyance of semi-finished products. In this particular case, an optibelt ALPHA V AT20 ST was coated with the coating material Sylomer L, green, PU foam. Afterwards, grooves and holes were cut out via water jet, and vacuum pockets were milled with an NC milling machine. With such belt the semi-finished products can be conveyed on to further processing steps via vacuum technology. For a special machinery manufacturer OPTIBELT has deve - loped a solution (see picture 2), for the conveyance of cuton-demand material (pipe, square and rectangular profiles) without changing the belt type. Furthermore, a slipping of the cutted material due to the startstop-frequency has to be prevented. The belts (depending on the number of pieces 4-6 belts) do run synchronously in parallel depending on the lengths of the cutted profile. The belt back is equipped with foam profiles (Sylomer R, blue, PU foam) and PU cleats in order to ensure a conveyance with exact positioning of the individually cut profiles. Picture 2: Customised solution for the conveyance of cut material The customised solution shown in picture 3 was ordered by a customer from the pet / animal food industry in order to convey empty pet / animal food packaging to filling stations. The belt back was coated with a natural rubber (RP 400, yellow) and equipped with cleats. The welded cleats have an additional glass fibre reinforced protective layer in order to counter the high shear forces of the sharp-edged pet / animal food packaging. Furthermore, the cleats ensure an exact positioning of the goods to be conveyed. Picture 3: Customised solution for the conveyance of pet / animal food packaging

24 conveyor drives optibelt ALPHA Special online CLEAT SELEcToR SYStematically selecting the adequate cleat With help of a new online tool, OPTIBELT now offers a quick and easy access to their comprehensive range of cleats. With the cleat selector, customers are now able to systematically select the perfect cleat for their individual conveyance solution from a standard range of over 300 different cleat shapes. Furthermore the cleats can also be adapted according to customers own specifications. This way, the new cleat selector helps to find the suitable cleat shape for every application. The most important basic data concerning shape, material and size of the cleats can be accessed via the selection screen. Thus the customer can search for their best suited solution. The according search result lists all available cleat designs with a detailed picture including all technical specifications such as width, height, thickness, welding thickness and material. Every hit can easily be downloaded as pdf-file or CAD file for free. In case there is no suitable cleat in our product range though, OPTIBELT can produce individual shapes and designs on demand even in small series. All cleats are suitable for the use on thermo-plastic belts by optibelt: ALPHA V, ALPHA flex or ALPHA linear. According to the requirements of the customer, the cleats are either welded on, chemically bound or attached mechanically. The cleat selector can be directly accesses via http://www.optibelt.com/cleat-selector

conveyor drives 25 optibelt ATC system FOR FLEXIBLE CONVEYOR APPLICatIONS Profile ATC10 ATC profile with cut-outs for ATC inserts in every tooth Punching of a through hole with the ATC punching tool Users of the ATC system are able to install screw-on cleats quickly and easily upon any tooth onsite. The user can easily screw-on and detach the connection. This way, the same drives and base belt can be adapted to different goods simply by using different types of screw-on cleats. The costs for stocking up wear and tear spare parts can be reduced by using a detachable cleat fixing. ATC inserts allow for the direct screwing-on of e. g. high-precision metal workpiece carriers without welded, specially manufactured cleats with inserts. Screwon cleats are able to transmit more power than permanent cleats. Furthermore, the minimum pulley diameter is smaller despite the same connection size. Screw-on cleats for the ATC system are available on request. Using the ATC system, ATC inserts are placed in the pre-moulded cut-out in the belt tooth to fix the screw-on cleat in place. These cut-outs are standard features for all teeth of the optibelt ALPHA V timing belt in profile ATC10. Installation size of a screw-on cleat, centre-to-centre distance a according to the ATC insert Cleats for the belt width 50 mm and 100 mm which were designed for a common mounting system in the belt market using single inserts are also compatible with the ATC system for the profile ATC10. Existing cleats can be used without any additional effort. accessories 1 2 3 ATC profile with punched holes for ATC inserts and installation of a screw-on cleat 1 2 3 optibelt ATC-PT punching tool optibelt ATC-IN insert material: Zinc, stainless steel Screw-on cleat

26 conveyor drives optibelt ATC system CLaSSIFIcation and characteristics ATC standard belt width [mm] ATC belt profile ATC insert Number of ATC inserts / blind holes per belt tooth Centre-to-centre distance blind holes or threads [mm] Thread size Minimum belt length ALPHA V [mm] Note 50 ATC10 ATC-IN M4 25 1/2 25 M4 850 ex stock 100 ATC10 ATC-IN M4 25 2/4 25 M4 1050 ex stock 150 ATC10 ATC-IN M4 25 3/6 25 M4 1150 ex stock The top surface of the belt is smooth and, at the start, does not have any punched holes. Before placing the ATC insert, the preformed blind holes within the cut-out of the chosen tooth have to be punched with the ATC-PT punching tool in order to get through holes. Making the punching easier, the optibelt ALPHA V profile ATC10 has no tension members in the area where the blind holes are. The AlpHA ATC in standard design is optionally available with polyamide fabric on the teeth (PAZ). For applications in the food or pharmaceutical industry, a special design with stainless steel tension cords is also available. The zinc-die cast (ZN) or stainless steel (RF) ATC insert consists of two bushes which are joined by a durable bar. The ATC insert completely follows the contour of the belt tooth, not touching the teeth of the timing belt pulley. Position of the cut-outs of the profiles 50, 100 and 150 ATC10 for inserts ATC-in M4 25

conveyor drives 27 optibelt atc-in INSERTS CLASSIFICatION TO BELT PROFILES AND CHARACTERISTICS Belt width Belt profile ATC insert Number of inserts per belt tooth Centre-to-centre distance for through holes Thread size Minimum length 1 for the narrowest belt width Note [mm] [mm] [mm] 40-150 AT10 ATC-IN M4 25 free choice depending on belt width 25-150 AT10 ATC-IN M4 14 free choice depending on belt width 25 M4 700 ALPHA Special made to order 14 M4 700 ALPHA Special made to order 1 Minimum length for wider width on request, please note minimum lengths of the basic belts. For an optibelt ALPHA Special of 32 mm belt width we recommend the second standard insert ATC-IN M4 14. This insert has similar installation sizes as the insert ATC-IN M4 25, the centre-to-centre distance, however, is reduced from 25 mm to 14 mm. optibelt ALPHA Special with AT tooth with forward machined cut-outs including through holes optibelt ATC-PP punch plier optibelt ATC-IN inserts available in lot sizes of 10 / 25 /100 pieces

28 MecHanical connections mechanical BESIDES THE TIMING Belt joint ZS / ZSi, CONNECTIONS HAS BEEN EXTENDED BY TIMING BELT joint ZS AND ZSi THE TIMING BELT joint ZS / ZSi IS DESIGNED FOR THE REPEATED DETACHING AND joining OF TtIMIMG BELTS IN THE application. Both designs are available in stainless steel for the profiles AT10 and H ex stock. Thus, this connection can be used in combination with the suitable timing belts in the food and pharmaceutical industry. For the profile T10 the inserts for the toothed side are made of brass which is not suitable for the application in the food and pharmaceutical industry. The back plates are connected with the inserts on the toothed side via bolts that are screwed on through the belt. The belt back of the design ZSi is 1 mm higher so that the back plates are enbedded into the timing belt and end at the height of the belt back. The standard widths belt joints for the profiles AT10 and T10 are 25; 32 and 50 mm, and for the H profile 25.4; 38.1 and 50.8 mm. Further intermediate widths and width exceeding 50 mm on request.

MecHanical connections 29 TIMING BELT joints THE RANGE OF MECHANICAL THE Version PINJOIN TIMING BELT joint PINJOIN THE TIMING BELT joint PINJOIN IS Designed for a singular connection of timing belts directly into the application on site. The belt is joined via threaded pins made of stainless steel in cross holes all through the tooth. Thus, this connection can be used in combination with the suitable timing belts in the food and pharmaceutical industry. The pinjoin connection is also suitable for the connection of coated belts. In the spot of the connection, however, the coating is bluntly placed face to face. The standard width ranges of lock connections for the profile AT10 are 25, 32 and 50 mm. Further profiles, intermediate widths and width exceeding 50 mm on request.

30 RoUND belts optibelt RR / RR Plus polyurethane RoUND belts optibelt round belts consist of high quality materials which are produced as openended rolls in different diameters from 2 mm to 20 mm in special production processes. The design optibelt RR PLUS is equipped with an additional polyester tension cord. CHARACteRISTICS Advantageous friction coefficient Good skid resistance during conveyance Good wear and abrasion resistance High elasticity, good absorption High tensile strength Colour proof, leaves no stains resistant against grease, oil and various chemical UV and ozone resistant In the design optibelt RR PLUS extremely low stretch ADvaNtageS welding on the spot, also in design optibelt RR PLUS No disassembly of the drive / shafts Quick breakdown elimination Short downtimes Simple storage (on rolls) Immediately available Diverse construction designs, as every desired length can be produced optibelt RR RouND BeltS ARE MAINLY USED IN transport SYStems, E. G. FOR THE CONveYaNCE OF: Tiles, plates, flat glass Veneers in wood processing Roof tiles, marble, concrete slabs Cardboard conveyance in the packaging sector Also as guiding belts for the conveyance of bottles and cans optibelt RR PLUS is especially suitable for use in long conveyors

RoUND belts 31 shore A 82 YELLOW Application: for small deflecting pul - leys, flexible at low temperatures, very elastic quality, low power transmission capability. shore A 85 LIGHT BLUE FDA Application: food industry for direct contact with food. shore A 88 GREEN (SMOOTH / ROUGH) Application: in all areas with medium loads; the rough surface design offers advantages for the conveyance of wet or greasy products plus the slaving effect is optimised. shore A 92 WHITE Application: for medium to heavy loads; the design white still offers enough flexibility. For continuous operation even at higher temperatures. shore A 98 BLUE Application: especially for extreme loads and high temperatures; very strong quality, please respect the minimum pulley diameter by all means. shore A 65 BLACK Application: for special applications, belt diameters from 5 mm to 12 mm available, very flexible at low temperatures, extremely soft material.

Timing belt pulleys StaNDARD-Timing belt pulleys Timing belt pulley according to draft Arntz Optibelt Group, GerMAny

Timing belt pulleys 33 optibelt ZRS StaNDARD TIMING BELT pulley pre-bored Profile width code number of teeth XL 037 10 72 L 050 10 84 075 10 84 100 10 84 H 075 14 48 100 14 120 150 14 120 200 14 120 300 16 120 XH 200 18 96 300 18 96 400 18 96 Standard timing belt pulley with cylindrical drilled hole Profile belt width [mm] number of teeth 5M 9 12 72 15 12 72 25 12 72 8M 20 22 192 30 22 192 50 22 192 85 22 192 14M 40 28 216 55 28 216 85 28 216 115 28 216 170 28 216 Profile belt width [mm] number of teeth T5 10 10 60 16 10 60 25 10 60 T10 16 10 60 25 10 60 32 18 60 50 18 60 AT5 10 12 60 16 12 60 25 12 60 AT10 16 15 60 25 15 60 32 18 60 50 18 60 Arntz Optibelt Group, GerMAny

34 timing belt pulleys optibelt ZRS StaNDARD timing belt pulleys for taper bushes Profile belt width [mm] number of teeth 5M 15 34 150 8M 20 22 90 30 22 144 50 28 192 85 34 192 14M 40 28 216 55 28 216 85 28 216 115 28 216 170 38 216 Taper bushes Standard timing belt pulley with taper bushes Profile width code number of teeth L 050 18 120 075 18 120 100 18 120 H 100 16 120 150 18 120 200 18 120 300 20 120 XH 200 18 48 300 18 48 400 20 48

Timing belt pulleys 35 Timing belt pulley according to draft CUStomISED SOLUTION 50 Ø 62,85-0,05 Profile: Profil: T5 T5 Number Zähnezahl: of teeth: z = 40z = 40 Pitch: Teilung: 5 5 Tolerance Toleranzband: band: 0,05 0,05 R0,3 1,95 +0,05 R0,2 1,85 +0,05 A A (1:1) 8 JS9 / 3,3 +0,2 8 2 0,013 A Ra1,6 28,3 +0,2 66,4 54 1 x 45 A A Ra1,6 1 x 45 24,5 27 Ø25 G7 3,2 3-D-view 3-D-Ansicht M 1:2 Sole and exclusive holder of all copyright and usage rights as well as other rights of usage and exploitation: ARNTZ OPTIBELT GROUP, HöXTER / GERMANy. Any type of use, reproduction or any exploitation or passing on to third parties requires the previous written approval of the Arntz Optibelt Group, HöXTER / GERM ANy. Arntz Optibelt Group, GerMAny Print: 314584/0113Hux

OPTIBELT GmbH 37671 Höxter T + 49 (0) 52 71-6 21 F + 49 (0) 52 71-97 62 00 GERMANY E info @ optibelt.com Corveyer Allee 15 ECOBELT GmbH Im Emerten 11 T + 49 (0) 57 51-9 67 79-0 31737 Rinteln F + 49 (0) 57 51-9 67 79-10 GERMANY E info@ecobelt.com www.optibelt.com