INSTALL GUIDE DOCUMENT NUMBER 90 REVISI DATE 0809 IRMWARE OEM-AL(RS)-CH8-[OL-MDB-ALL] HARDWARE OL-MDB-ALL ESSORIES OL-LOADER (REQUIRED) TERMS O USE: Automotive Data Solutions Inc. ( ADS ) products are strictly intended for installation by Certified Technicians who are employed by a registered business specialized in the installation of automotive aftermarket electronics products. Prior to beginning installation of an ADS product in a vehicle, it is the Certified Technician s responsibility to review the most current Product Guide, Install Guide and vehicle-specific notes available in Weblink. ADS is not responsible for any damages whatsoever, including but not limited to any consequential damages, incidental damages, damages for loss of time, loss of earnings, loss of profit, commercial loss, loss of economic opportunity and the like that may or may not have resulted from the use, misuse, improper installation or operation of its products. ADS reserves itself the right to suspend any Weblink account without notice and decline to offer technical support to non-certified Technicians, non-compliant Certified Technicians or end users. Automotive Data Solutions Inc. 08 BEORE INSTALLATI - Connect module to computer - Login to Weblink account - lash firmware to module (module is not preloaded with firmware) - Use accessories accordingly (accessories are sold separately)
PAGE O DOC.: #90 0809 VEHICLE LIST - O EATURES DOOR UNLOCK ARM OEM ALARM DISARM OEM ALARM BRAKE PEDAL STATUS OUTPUT TACHOMETER OUTPUT SECURE TAKEOVER 00 / 00 / 00 Diesel STD key (Tip-Start) AT - 00 / 00 / 00 Diesel STD key (Tip-Start) AT 8 INSTALL TYPE MAKE RAM Automotive Data Solutions Inc. 08 RAP SHUTDOWN CTRL DOOR LOCK GLOW PLUGS STATUS X LOCK /STANDALE MOD. 8 TRUNK STATUS OUTPUT DATA IMMOBILIZER BYPASS - 00 / 00 / 00 STD key (Tip-Start) AT DOOR STATUS OUTPUT YEAR 00 / 00 / 00 STD key (Tip-Start) AT TRUNK/HATCH RELEASE MODEL NOTE I WARNING: All vehicle doors must be closed and locked prior to remote start sequence.
PAGE O DOC.: #90 0809 BOX CTENTS - O BOX CTENTS WHITE WHITE PIN BLACK CNECTOR PIN WHITE CNECTOR MODULE WHITE BLUE PROGRAMMING BUTT 0 PIN BLACK CNECTOR PIN WHITE CNECTOR LED A B C E D 0 9 8 BLACK PIN WHITE CNECTOR DATA CABLE PIN BLUE CNECTOR DATA CABLE BLACK DATA PORT (WEBLINK, R, TELEMATIC) WEBLINK CABLE (required accessory sold separately) WEBLINK CABLE MODULE DATA PORT COMPUTER USB PORT PIN BLACK CABLE Automotive Data Solutions Inc. 08
PAGE O DOC.: #90 0809 00 / 00 Diesel / 00 / 00 Diesel / STD key AT Automotive Data Solutions Inc. 08 POLARITY MODULE LOCATI COMPENT LOCATOR DA 0 Red (+) DA 0 (-) Key position DA 0 Purple/Brown (MUX) DA 0 White/Green CanH D0A pin 0 Gray/White OBDII connector CanL D0A pin Yellow OBDII connector Parking Light DA 0 pin 0 White/Brown (MUX) Parking light switch A - Imo Lin WIRE COLOR POSITI V Ground CNECTOR NAME CNECTOR TYPE WIRE DESCRIPTI CNECTOR COLOR RAM 00 / 00 Diesel STD key AT YEAR MODEL MAKE TYPE - WIRE CHART - O V DA 0 Red (+) Ground DA 0 (-) Key position DA 0 Purple/Brown (MUX) DA 0 White/Green CanH D0A pin 0 Gray/White OBDII connector CanL D0A pin Yellow OBDII connector Parking Light DA 0 pin 0 White/Brown (MUX) Parking light switch A - Imo Lin
PAGE O DOC.: #90 0809 TYPE - WIRING DIAGRAM - O IGNITI NODE MODULE A A B MUX - 0 KEY POSITI (MUX) GROUND (-) - 0 C E DATA D. A A B BLACK IMO LIN - 0 0 GRAY/YELLOW (NC) 0 GRAY/RED (NC) 0 GREEN/YELLOW (NC) 0 GREEN/RED (NC) 0 BLUE/YELLOW (NC) 0 BLUE/RED (NC) 0 PINK - KEY POSITI (MUX) INPUT 0 PINK/BLACK (NC) 0 ORANGE - KEY POSITI (MUX) OUTPUT 0 ORANGE/WHITE (NC) 0 ORANGE/BLACK - IMO LIN 0 BROWN/YELLOW - CANL 0 BROWN/RED - CANH 0 YELLOW - PARKING LIGHT (MUX) OUTPUT 0 YELLOW/RED (NC) 0 YELLOW/BLACK (NC) C OBDII CNECTOR OBDII CANL - CANH - 0 8 9 0 PARKING LIGHT SWITCH 0 WHITE (NC) 0 WHITE/RED - LIN CUT VEHICLE SIDE 0 WHITE/BLACK - LIN CUT CNECTOR SIDE BLACK PARKING LIGHT (MUX) - 0 E V (+) - 0 B D 0 0 0 0 BLUE/WHITE (NC) WHITE (NC) BLACK - GROUND RED - V (+) 8 9 0 WITHOUT A COMPATIBLE ESSORY OR 8 9 0 DATA CABLE COMPATIBLE ESSORY 0 GREEN/BLACK- HOOD STATUS (-) INPUT 0 BLUE/BLACK (NC) 0 RED/WHITE (NC) 0 BROWN (NC) 0 PURPLE/YELLOW (NC) 0 PURPLE/BLACK (NC) 0 WHITE (NC) 08 BLACK/WHITE (NC) 09 GREEN (NC) 0 PURPLE/WHITE (NC) Automotive Data Solutions Inc. 08 WITH A COMPATIBLE ESSORY. IMPORTANT: SEE THE COMPATIBLE ESSORIES PAGE OR DETAILS. WITHOUT OEM HOOD SWITCH: INSTALL AND CNECT TO ATERMARKET HOOD SWITCH ATERMARKET HOOD SWITCH (-)
PAGE O DOC.: #90 0809 00 Diesel / 00 Diesel / 00 Diesel STD key AT Automotive Data Solutions Inc. 08 8 POLARITY MODULE LOCATI COMPENT LOCATOR DA 0 Red (+) DA 0 (-) Key position DA 0 Purple/Brown (MUX) Imo Lin DA 0 White/Green CanH Gray 0 pin 0 Orange Trailer module, right of steering column CanL Gray 0 pin 0 Yellow Trailer module, right of steering column Parking Light DA 0 pin 0 White/Brown (MUX) Parking light switch WIRE COLOR POSITI V Ground CNECTOR NAME CNECTOR TYPE WIRE DESCRIPTI CNECTOR COLOR 8 RAM 00 / 00 / 00 STD key AT YEAR MODEL MAKE TYPE - WIRE CHART - O V DA 0 Red (+) Ground DA 0 (-) Key position DA 0 Purple/Brown (MUX) Imo Lin DA 0 White/Green CanH Gray 0 pin 0 Orange Trailer module, right of steering column CanL Gray 0 pin 0 Yellow Trailer module, right of steering column Parking Light DA 0 pin 0 White/Brown (MUX) Parking light switch
PAGE O DOC.: #90 0809 TYPE - WIRING DIAGRAM - O IGNITI NODE MODULE A A B MUX - 0 KEY POSITI (MUX) GROUND (-) - 0 C E DATA D. A A B BLACK IMO LIN - 0 0 GRAY/YELLOW (NC) 0 GRAY/RED (NC) 0 GREEN/YELLOW (NC) 0 GREEN/RED (NC) 0 BLUE/YELLOW (NC) 0 BLUE/RED (NC) 0 PINK - KEY POSITI (MUX) INPUT 0 PINK/BLACK (NC) 0 ORANGE - KEY POSITI (MUX) OUTPUT 0 ORANGE/WHITE (NC) 0 ORANGE/BLACK - IMO LIN 0 BROWN/YELLOW - CANL 0 BROWN/RED - CANH 0 YELLOW - PARKING LIGHT (MUX) OUTPUT 0 YELLOW/RED (NC) 0 YELLOW/BLACK (NC) C TRAILER PACK CNECTOR B CANL - 0 CANH - 0 GRAY 8 9 0 0 WHITE (NC) 0 WHITE/RED - LIN CUT VEHICLE SIDE 0 WHITE/BLACK - LIN CUT CNECTOR SIDE 0 0 0 0 BLUE/WHITE (NC) WHITE (NC) BLACK - GROUND RED - V (+) PARKING LIGHT SWITCH BLACK PARKING LIGHT (MUX) - 0 E V (+) - 0 C D 8 9 0 WITHOUT A COMPATIBLE ESSORY OR 8 9 0 DATA CABLE COMPATIBLE ESSORY 0 GREEN/BLACK- HOOD STATUS (-) INPUT 0 BLUE/BLACK (NC) 0 RED/WHITE (NC) 0 BROWN (NC) 0 PURPLE/YELLOW (NC) 0 PURPLE/BLACK (NC) 0 WHITE (NC) 08 BLACK/WHITE (NC) 09 GREEN (NC) 0 PURPLE/WHITE (NC) Automotive Data Solutions Inc. 08 WITH A COMPATIBLE ESSORY. IMPORTANT: SEE THE COMPATIBLE ESSORIES PAGE OR DETAILS. WITHOUT OEM HOOD SWITCH: INSTALL AND CNECT TO ATERMARKET HOOD SWITCH ATERMARKET HOOD SWITCH (-)
PAGE 8 O DOC.: #90 0809 MODULE PROGRAMMING PROCEDURE - O 0 Close driver door. Re-open driver door to wake up data bus. 0 0 0 Press Unlock on OEM remote. If the vehicle is not equipped with an OEM remote, press the module programming button. 08 Wait, LED will flash GREEN once [x]. If LED does not flash GREEN, press Unlock on OEM remote again. 09 Turn key to position. 0 Wait, LED will turn solid RED. 0 Insert key into ignition. WARNING: Do not press module programming button. Connect power first. Connect module to vehicle. Turn key to position. Turn key to position. Connect module to computer and proceed with extended programming. Turn key to position. Wait, LED will flash GREEN. Turn key to position. Wait, LED will turn solid GREEN for seconds. 0 0 Remove key. Automotive Data Solutions Inc. 08 Turn key to position. WARNING: Disconnect power last. Disconnect module from vehicle. 8 Turn key to position.
MODULE PROGRAMMING PROCEDURE - O 9 Turn key to position. 0 PAGE 9 O DOC.: #90 0809 Module Programming Procedure completed. Automotive Data Solutions Inc. 08
VALET MODE PROGRAMMING PROCEDURE - O NOTE: In Valet Mode, the Remote starter is not functional. Keyless entry, Lock and Unlock will remain functional. See R kit user manual for alternate valet mode programming. 0 Time restriction. Complete next step within seconds. 0 PAGE 0 O DOC.: #90 0809 To exit valet mode: repeat steps to. Cycle ignition five times [x /] rapidly. ENGINE STOP 0 0 Wait, LED will turn solid RED for seconds. Set ignition to position. ENGINE STOP 0 Valet Mode Programming Procedure completed. Automotive Data Solutions Inc. 08
PAGE O DOC.: #90 0809 MODULE NAVIGATI PROCEDURE - O It is mandatory to exit the Module Navigation at the end of this procedure. ailure to exit the Module Navigation will drain vehicle battery. To exit the Module Navigation at any time: ollow STEP. 0 Module must be programmed to the vehicle. 0 Use the Module Navigation Chart on the next page. 0 Set ignition to position. 0 TO ESS THE MENUS: Press and hold programming button until LED turns solid GREEN. 08 IN THE MENUS: Press the programming button as many times as the menu number indicates. LED will flash GREEN an equal amount of times continuously. 09 0 TO ESS THE OPTIS: Press and hold programming button until LED turns solid RED. 0 IN THE OPTIS: Press the programming button as many times as the option number indicates. LED will flash RED an equal amount of times continuously. TO ESS THE SETTINGS: Press and hold programming button until LED turns solid GREEN. Configure every other setting and proceed to step. [Z] LED will flash GREEN as many times as the current (or default) setting number, continuously. MANDATORY: EXIT MODULE NAVIGATI. Press and hold programming button for seconds. LED will flash RED rapidly. Release programming button. LED will turn. [Z] IN THE SETTINGS: Press the programming button as many times as necessary to access your setting. LED will flash GREEN an equal amount of times continuously. Module navigation completed. To return to the MENUS: exit the Module Navigation and redo the Module Navigation Procedure. ailure to exit the Module Navigation will drain vehicle battery. [Y] To save and return to the OPTIS: Press and hold programming button until LED turns solid RED. [Y] LED will flash RED as many times as the current option number continuously. ENGINE STOP 0 0 [X] Automotive Data Solutions Inc. 08
PAGE O DOC.: #90 0809 [Y] OPTIS [X] MENUS MODULE NAVIGATI CHART: NOTES I Default settings are listed in bold. 0 0 0 0 0 0 0 0 0 ENABLE 0 DISABLE* 0 SEC 0 90 SEC 0 0 MIN 0 0 MIN 0 N/A 0 0 MIN 0 0 MIN 0 0 MIN 0 MIN 0 MIN 0 0 MIN 0 MIN 08 MIN 0 0 SEC 0 0 SEC 0 08 SEC 0 0 SEC 0 SEC 0 0 SEC 0 SEC 08 0 SEC 0- N/A 0 N/A 0 0 N/A 0 II Make sure the option is covered on the vehicle before attempting to change the setting. 0 0 0 0 0 0 0 [Z] SETTINGS MODULE NAVIGATI CHART - O DISARM/UNLOCK BEORE RELOCK ATER RELOCK ATER SHUTDOWN ORCE UNLOCK ALL IRST PRESS TAKEOVER SECURE TAKEOVER DELAY N/A CIGURATI 08 09 0-0 Technical Support only MODULE RUN TIME WAIT TO DELAY N/A *Vehicle will shutdown when a door is opened. Automotive Data Solutions Inc. 08
[X] NUMBER O PARKING LIGHT LASHES DIAGNOSTIC REMOTE ER ERROR CODES - O I WARNING: The following applies only when the parking lights are connected and supported by the system. 0 oot brake is. 0 Hood is open. II After a remote starter failure, the parking lights will flash [X] number times to indicate an error code. See table. 0 Engine tach signal is lost. 0 System is in Valet Mode. 0 Vehicle is moving (VSS). 08 Glow plug timeout error. REMOTE ER ERROR CODES: NOTES Automotive Data Solutions Inc. 08 PAGE O DOC.: #90 0809
I II III DURING PROGRAMMING DURING REMOTE WITH IGNITI Automotive Data Solutions Inc. 08 DIAGNOSTIC TEST MODULE LED STATUS MODULE DIAGNOSTICS - O lashing RED Missing/wrong information from firmware or vehicle. Solid RED Module waiting for more vehicle information. lashing GREEN Additional steps required to complete module programming. Solid GREEN then Module correctly programmed. No activity or module already programmed. lashing RED Module incorrectly programmed. Solid RED Module incorrectly programmed. lashing GREEN Module correctly programmed and operational. Solid GREEN then Reset in progress. Invalid ground when running status from remote starter. lashing RED Module incorrectly programmed or connected. Solid RED Module not programmed. Waiting for more vehicle information. lashing GREEN alse ground when running status from remote starter. Solid GREEN then Reset in progress. Module at rest and ready for a remote start sequence. PAGE O DOC.: #90 0809
MODULE RESET PROCEDURE - O 0 Disconnect all connectors from module except the BLACK -PIN connector. 0 Reconnect all connectors. 0 Disconnect the BLACK -PIN connector. 08 Repeat programming procedure. 0 PRESS AND HOLD programming button while connecting the BLACK -PIN connector. ailure to follow procedure may result with a DTC or a CHECK ENGINE error message. 0 Wait, LED will flash RED. RELEASE programming button. 0 LED will turn RED for seconds. 0 Module RESET completed. Automotive Data Solutions Inc. 08 PAGE O DOC.: #90 0809
TAKEOVER PROCEDURE - O All vehicle doors must be closed and locked prior to remote start sequence. 0 Press and release BRAKE pedal. 0 Time restriction. Complete steps to within seconds. 0 Take over procedure completed. 0 Press unlock on OEM or aftermarket remote. ailure to follow procedure will result in vehicle engine shutdown. 0 Open driver door and enter vehicle. 0 Close driver door. 0 PAGE O DOC.: #90 0809 Turn key to position. Automotive Data Solutions Inc. 08
INSTALLATI CHECKLIST - O PAGE O DOC.: #90 0809 CHECKLIST WARNING: Vehicle engine will start many times. Test in a well ventilated area. Close all vehicle doors, hood and trunk. Press LOCK button three times [x] rapidly on the OEM keyfob to remote start vehicle. Question : Does the vehicle remote start? YES: Go to next step. NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call technical support, if the problem persists. Press LOCK button three times [x] rapidly on the OEM keyfob to shut down vehicle. Question : Does the vehicle shut down? YES: Go to next step. NO: Repeat step. If the problem persists, press on the brake pedal once [x] to shut down the vehicle and call technical support. RAP Shutdown test Question : Did the radio, interior controls, and headlights turn off within 0 seconds after remote start shutdown? YES: Go to next step. NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support, if the problem persists. Open hood. If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 8 Press LOCK button three times [x] rapidly on the OEM keyfob to remote start vehicle. Question : Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 9 Close hood. 0 Enter vehicle and close the doors. Press LOCK button three times [x] rapidly on the OEM keyfob to remote start vehicle. Wait for the vehicle to start. Press brake pedal. Question : Does the vehicle shut down? YES: Go to next step. Exit vehicle. Installation checklist completed. NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support. Automotive Data Solutions Inc. 08