Corrosion Control Equipment and Supplies

Distributed by:! Corrosion Control Equipment and Supplies Houston Office: 248 McCarty Dr. Houston, TX 77029-1195 (713) 672-8251 Fax (713) 672-6636 1-800-CLEMTEX www.clemtex.com clemtex@clemtex.com Dallas Branch: 4770 Gretna Dallas, TX 75207 (214) 631-0584 Fax (214) 631-5824 1-800-BLAST 97 Corpus Christi Branch: 4750 Westway Corpus Chrisi, TX 78408 (361) 882-8282 Fax (361) 882-6029

Binks Model 95A Automatic Conventional Air Spray Gun and Binks Model 95AV (For Ceramic Coatings) Conventional Air Spray Gun STANDARD SET-UPS AVAILABLE (SEE PG. 9). OPTIONAL SET-UPS PLEASE ORDER SEPARATELY (SEE PGS. 8 & 9). AUTOMATIC AIR SPRAY GUN WITH STAINLESS STEEL FLUID INLET MODEL 95A AND 95AV SPRAY GUN The Binks Model 95A Automatic Spray Gun is a conventional style air spray gun. It incorporates all stainless steel fluid inlet, fluid nozzle, and fluid needle for spraying a wide variety of conventional and waterborne coatings. Model 95AV incorporates tungsten carbite fluid nozzles used in ceramic and abrasive coating applications. It is also pneumatically activated for application with reciprocating, rotary, spindle machines, and in stationary gun set-ups. Exceptionally rugged in construction, the Binks Model 95A and 95AV guns are built to stand up under hard, continuous use. However, like any other fine precision instrument, their most efficient operation depends on a knowledge of their construction, operation, and maintenance. Properly handled and cared for, these guns will produce beautiful, uniform finishing results long after other spray guns have worn out. Replaces Part Sheet 77-2641R-7 Part Sheet 77-2641R-8

In this part sheet, the words WARNING, CAUTION and NOTE are used to emphasize important safety information as follows:!! CAUTION NOTE WARNING Hazards or unsafe practices which could result in severe personal injury, death or substantial property damage. Hazards or unsafe practices which could result in minor personal injury, product or property damage.! WARNING Read the following warnings before using this equipment. Important installation, operation or maintenance information. READ THE MANUAL Before operating finishing equipment, read and understand all safety, operation and maintenance information provided in the operation manual. INSPECT THE EQUIPMENT DAILY Inspect the equipment for worn or broken parts on a daily basis. Do not operate the equipment if you are uncertain about its condition. WEAR SAFETY GLASSES Failure to wear safety glasses with side shields could result in serious eye injury or blindness. NEVER MODIFY THE EQUIPMENT Do not modify the equipment unless the manufacturer provides written approval. DE-ENERGIZE, DISCONNECT AND LOCK OUT ALL POWER SOURCES DURING MAINTENANCE Failure to De-energize, disconnect and lock out all power supplies before performing equipment maintenance could cause serious injury or death. KNOW WHERE AND HOW TO SHUT OFF THE EQUIPMENT IN CASE OF AN EMERGENCY OPERATOR TRAINING All personnel must be trained before operating finishing equipment. PRESSURE RELIEF PROCEDURE Always follow the pressure relief procedure in the equipment instruction manual. EQUIPMENT MISUSE HAZARD Equipment misuse can cause the equipment to rupture, malfunction, or start unexpectedly and result in serious injury. NOISE HAZARD You may be injured by loud noise. Hearing protection may be required when using this equipment. KEEP EQUIPMENT GUARDS IN PLACE Do not operate the equipment if the safety devices have been removed. PROJECTILE HAZARD You may be injured by venting liquids or gases that are released under pressure, or flying debris. PINCH POINT HAZARD Moving parts can crush and cut. Pinch points are basically any areas where there are moving parts. STATIC CHARGE Fluid may develop a static charge that must be dissipated through proper grounding of the equipment, objects to be sprayed and all other electrically conductive objects in the dispensing area. Improper grounding or sparks can cause a hazardous condition and result in fire, explosion or electric shock and other serious injury. FIRE AND EXPLOSION HAZARD Never use 1,1,1-trichloroethane, methylene chloride, other halogenated hydrocarbon solvents or fluids containing such solvents in equipment with aluminum wetted parts. Such use could result in a serious chemical reaction, with the possibility of explosion. Consult your fluid suppliers to ensure that the fluids being used are compatible with aluminum parts. AUTOMATIC EQUIPMENT Automatic equipment may start suddenly without warning. FOR FURTHER SAFETY INFORMATION REGARDING BINKS AND DEVILBISS EQUIPMENT, SEE THE GENERAL EQUIPMENT SAFETY BOOKLET (77-5300). 2

Binks Models 95A and 95AV AUTOMATIC CONVENTIONAL SPRAY GUNS Typical Arrangement Diagram and Hook-up for Combined Fan and Atomizing Air Separate Fan Air Inlet Port (Unplug to operate) (See pg. 4 for instructions) Fluid Inlet Atomizing and Fan Air Combined Inlet Mounting Lockscrew Mounting Hole (1/2" Dia.) Cylinder Air Inlet Side Port Control Assembly (Fan Pattern Control) Fluid Needle Stroke Adjustment Fluid Inlet 3/8" NPS Atomizing Air Inlet 1/4" NPS Cylinder Air Inlet 1/4" NPS Oil and Water Extractor Regulated Cylinder Air From Oil and Water Extractor Regulated Fluid Inlet Four Gun Material Manifold 95A or 95AV Automatic Gun Combined Fan and Atomizing Air Four Gun Air Manifold 3-Way Solenoid For some applications each gun may require individually regulated fluid and air inlet lines. 3

Binks Models 95A and 95AV AUTOMATIC SPRAY GUNS Typical Arrangement Diagram and Hook-up for Separate Fan and Atomizing Air (See Page 5 for Internal Modifications to Gun) Fan Air Inlet Mounting Hole (1/2" Dia.) Mounting Lockscrew Side Port Control Assembly (Fan Pattern Size Control) Fluid Inlet Cylinder Air Atomizing Air Inlet Fluid Inlet 3/8" NPS Cylinder Air Inlet 1/4" NPS Atomizing Air Inlet 1/4" NPS Fan Air Inlet 1/4" NPS Oil and Water Extractor Regulated Cylinder Air From Oil and Water Extractor Regulated Fluid Inlet Four Gun Material Manifold Atomizing Air 3-Way Pilot Valve 4 Gun Air Manifold 3-Way Solenoid Fan Air For some applications each gun may require individually regulated fluid and air inlet lines. GENERAL NOTES 1. Have at least 55-60 P.S.I. air pressure for cylinder s operating air. (Maximum 90 PSIG) 2. To reduce overspray and obtain maximum efficiency, always spray with lowest possible fluid/air pressure that produces an acceptable spray pattern. 3. The air line from gun to 3-way valve should be as short as possible for rapid operation. 4. All air used in the gun should be dirt and moisture free. (This is accomplished by using an oil and water extractor). 5. Shut off all fluid and air lines to gun if gun is to stand idle for any length of time. (This is to prevent build up or accumulation of minute leaks in the system and turning on the gun). 4

TO CHANGE FROM COMBINED FAN AND ATOMIZING AIR TO SEPARATE FAN AND ATOMIZING AIR 1. Unscrew end cap (28) and remove material needle (22) and attached parts (23, 24, 25) (see assembly drawing page 10). 2. Remove piston assembly (18) by injecting low pressure air into cylinder air port (A).! WARNING Use of excessive pressure will cause piston to exit gun body at high velocity, possibly resulting in personal injury or damage to spray gun components. When removing the piston, aim back of gun in a safe direction and do not use excessive air pressure. 3. With 5/32" allen wrench, remove plug (16) from hole (B) on inside of cylinder. 4. Insert set screw (46) into position as shown in side cut-away. (Set screw is packaged loose.) 5. Re-install plug (16). NOTE D.M. Nipple (32) shipped loose in a separate bag. 6. Re-install piston (20), 2 springs (26, 27), material needle (22) and end cap (28). (See assembly drawing page 10). 7. Remove plug (43) from the fan air port (C). 8. Install fitting (32) into port (C). (Fitting is packaged loose.) Plug (43) Remove and install D.M. Nipple (32) Fan Air Inlet (Optional) 28 C A Fluid Inlet Atomizing Air Inlet Cylinder Air Inlet B B View A Set Screw (46) Side Cut-Away Plug (16) View A NOTE Set screw (46) shipped loose in a separate bag. 5

SETUP FOR SPRAYING CONNECTING GUN TO MATERIAL HOSE Gun should be connected by a suitable length of 3/8" diameter material hose fitted with a connector with a 3/8" NPS(f) nut at gun end. 1/4" diameter hose is recommended for use with low viscosity materials. (Fluid hoses of different composition are available for special fluids. See Binks hose catalog for hose selection.) CONNECTING GUN TO ATOMIZING AIR Gun should be connected by a suitable length of 5/16" or 3/8" diameter air hose fitted with a connector and a 1/4" NPS(f) nut at gun end. CONNECTING GUN TO CYLINDER AIR Gun should be connected with 3/16" I.D. or 1/8" I.D. air hose of shortest length possible with 1/4" NPS(f) connector. Cylinder air must be connected to a 3-way manual air valve or 3-way solenoid valve to operate properly. OPERATING THE MODEL 95A AUTOMATIC SPRAY GUN CONTROLLING THE MATERIAL FLOW When fed from a pressure supply, an increase in the material pressure will increase the rate of flow. Correct fluid nozzle size insures correct material flow rate. If necessary, fluid flow can also be adjusted by adjusting the amount of needle travel. This is done by loosening lock nut (29) and adjusting control knob (30) until the correct needle travel is achieved. ADJUSTING AIR AND FLUID TIMING A 1/16" gap between the air piston assembly (18) and needle body (24) should be maintained (see figure 1). This will create needle motion that will allow adequate air flow before the fluid starts flowing. The gap may be adjusted by partially removing the material needle (22), screwing the needle (22) either in or out of the needle body (24) and locking it back into the gun while being sure to check the clearance between the air valve piston (18) and the needle body (24). ADJUSTING THE SPRAY PATTERN The width of the spray pattern is controlled by the side port control assembly (7). (See page 10). Turning this control clockwise until it is closed will give a round spray, turning it counterclockwise will widen the spray into a fan shape. The fan spray can be turned anywhere through 360 by positioning the air cap assembly (1) relative to the gun. To effect this, loosen air cap assembly, position nozzle, then, re-tighten air cap assembly. 22 1/16" Clearance 18 23 24 25 Figure 1 FLUID NEEDLE ADJUSTMENT DIAGRAM 6

MAINTENANCE LUBRICATION Monthly: Remove piston assembly (18) and lubricate the air cylinder chamber and needle valve spring with a coating of Gunners Mate (47). Also, lubricate side port control assembly (7) with oil. REMOVAL OF PISTON! CAUTION Never use lubricants containing silicone since these lubricants can cause finish defects. Binks Gunners Mate (47) is recommended. To remove the piston, first unscrew the end cap (28), remove 2 springs (26 & 27) and pull out the material needle (22) and attached parts (23, 24, & 25). Remove the piston by applying a few pounds of air pressure to the cylinder air inlet. This air pressure will cause the piston to pop out.! WARNING Excessive air pressure applied to the piston during removal may cause the piston to exit at a high velocity, resulting in personal injury. When removing the piston, aim back of gun in a safe direction and do not use excessive pressure. TO REPLACE NEEDLE SEAL AND GLAND ADAPTER IN FLUID INLET Remove end cap (28), springs (26 & 27) and assemble material needle (22) and attached parts (23, 24, & 25). Proceed to the front of the gun and remove air cap assembly (1) and fluid nozzle (2). Then, using wrench (44), unscrew head insert (4) and remove fluid inlet (33 or 34). Unscrew packing nut (39) and remove spring (38) and seal backup (37). Using a No. 10 x 1-1/4" coarse thread wood screw (Binks part no. 20-6536) or small sheet metal screw, remove the needle seal (36) and gland adapter (35). Replace gland adapter (35) and needle seal (36). Reinsert seal backup (37), spring (38) and screw on packing nut (39) a couple of turns so it fits loosely by hand. Reassemble fluid inlet (34) to gun body (5) with head insert (4). Tighten head insert using wrench (44). Reassemble fluid nozzle (2) and air cap assembly (1). Reinsert material needle (22) and attached parts (23, 24 & 25), springs (26 & 27) and screw on end cap (28). Finally, tighten packing nut (39) until it bottoms out on fluid inlet (34). CLEANING In certain states it is now against the law to spray solvents containing Volatile Organic Compounds (VOCs) into the atmosphere when cleaning a spray gun. In order to comply with these new air quality laws Binks recommends one of the following two methods to clean your spray finishing equipment: 1. Spray solvent through the gun into a closed system. An enclosed unit, or spray gun cleaning station, condenses solvent vapors back into liquid form which prevents escape of VOCs into the atmosphere. 2. Place spray gun in a washer type container. This system must totally enclose the spray gun, cups, nozzles, and other parts during washing, rinsing, and draining cycles. This type of unit must be able to flush solvent through the gun without releasing any VOC vapors into the atmosphere. Additionally, open containers for storage or disposal of solvent, or solvent-containing cloth or paper, used for surface preparation and cleanup may not be used. Containers shall be non-absorbent. To clean the gun, flush the fluid lines with solvent and blow air through the air lines to make sure all the air passages are dry.! CAUTION Never completely submerge the gun in solvent as this will dissolve the lubricating oil and dry out the seals. TROUBLESHOOTING FAULTY SPRAY A faulty spray may be caused by improper cleaning, dried materials around the fluid nozzle tip or in the air cap. Soak these parts in thinners that will soften the dried material and remove with a brush or cloth.! CAUTION Never use metal instruments to clean the air or fluid nozzles. These parts are carefully machined and any damage to them will cause faulty spray. If either the air cap assembly (1) or fluid nozzle (2) are damaged, these parts must be replaced before perfect spray can be obtained. INTERMITTENT SPRAY If the spray flutters, it is caused by one of the following faults: 1. Insufficient material available. Check supply and replenish if necessary. 2. Loose fluid nozzle (2). Tighten, but without using undue force. 3. Leakage at gland adapter (35) and needle seal (36). Tighten packing nut (39) if loose, and replace gland adapter and needle seal if necessary. 4. Fluid connection insufficiently tight or dirt on cone faces of connection. Correct as necessary. 5. Leaking cylinder air and/or inadequate pressure. 7

8 TYPE OF FLUID VISCOSITY TO BE SPRAYED VERY THIN VISCOSITY 14-16 Seconds No. 2 ZAHN Wash Primers Dyes Stains Solvents Water Inks THIN VISCOSITY 16-20 Seconds No. 2 ZAHN Sealers Lacquers Primers Inks Zinc Chromates Acrylics Lubricants MEDIUM VISCOSITY 19-30 Seconds No. 2 ZAHN Synthetic Enamels Varnishes Shellacs Fillers Primers Epoxies Urethanes Lubricants Wax Emulsions HEAVY (CREAM-LIKE) VISCOSITY Over 28 Seconds No. 4 FORD House Paint Wall Paint (Oil, Latex) Block Sealers Mill Whites Vinyls Acrylics Epoxies VERY HEAVY VISCOSITY Unaggregated Block Fillers Textured Coatings Fire Retardants Road Marking Paint Bitumastics Cellular Plastisols ADHESIVES Waterbase White Vinyl Glue Solvent Base Neoprenes (Contact Cements) CERAMICS & SIMILAR ABRASIVE MATERIAL Glazes, Engobes Porcelain Enamel NOZZLE AND NEEDLE SELECTION CHART FOR 95A and 95AV AUTOMATIC GUNS CFM AT * MAX. FLUID x AIR NOZZLE 30 50 70 PATTERN FLUID NOZZLES TYPE + PSI PSI PSI AT 8" NEEDLE 63SS x 63P PE 4.5 7.5 10.0 5.0" 763 63ASS x 63P PE 5.1 8.7 12.2 11.0" 763A 63BSS x 63PB PE 9.0 14.3 20.0 14.0" 763A 66SS x 66SD SE 7.9 12.1 10.5" 765 66SS x 66SK SE 11.0 15.2 19.5 13.0" 765 63BSSS x 200 PI 3.1 5.2 6.4 12.0" 763A 63ASS x 63P PE 5.1 8.7 12.2 11.0" 763A 63BSS x 63PJ PE 9.5 14.2 19.0 15.0" 763A 66SS x 66SA SE 4.4 7.1 10.0" 765 66SS x 66SG SE 6.8 10.5 8.0" 765 66SS x 66SK SE 11.0 15.2 19.5 13.0" 765 63BSS x 200 PI 3.1 5.2 6.4 12.0" 763A 63BSS x 63PB PE 9.0 14.3 20.0 14.0" 763A 63CSS x 63PE PE 9.5 15.0 20.0 13.0" 763A 63CSS x 63PR PE 9.5 15.5 19.5 18.0" 763A 65SS x 63PR PE 11.0 16.5 22.0 15.0" 765 66SS x 66SD SE 7.9 12.1 11.0" 765 66SS x 66SK SE 11.0 15.2 19.5 13.0" 765 63CSS x 200 PI 3.1 5.2 6.4 12.0" 763A 67SS x 206 PI 6.0 9.5 13.0 15.0" 767 68SS x 201 PI 4.6 6.8 9.1 11.0" 768 68SS x 101 PI 4.6 6.8 9.1 11.0" 768 66SS x 63PB PE 9.0 14.3 20.0 14.0" 765 67SS x 67PB PE 9.5 14.9 19.5 12.0" 767 68SS x 68PB PE 9.5 14.1 19.1 12.0" 768 68SS x 206 PI 6.2 9.8 13.2 15.0" 768 6SS x 68PB PE 9.5 14.1 19.1 12.0" 768 59ASS x 243 PI 6.4 10.0 13.4 RND" 759 59ASS x 244 PI 7.8 11.5 15.2 12.0" 759 59ASS x 245 PI 7.3 11.5 15.2 6.0" 759 59BSS x 250 PI 7.8 11.0 14.7 RND" 759 59BSS x 251 PI 7.8 11.5 15.2 12.0" 759 59BSS x 252 PI 7.8 11.5 15.2 12.0" 759 63CSS x 63PB PE 9.0 14.3 20.0 14.0" 763A 66SS x 63PR PE 9.5 15.5 19.5 15.0" 765 67SS x 67PB PE 9.5 14.1 19.1 12.0" 767 63SS x 66SD PE 7.9 12.1 16.2 4.0" 763 63ASS x 66SD PE 7.9 12.1 16.2 7.0" 763A 66SS x 66SD-3 PE 10.4 15.4 20.4 9.0" 765 63CVT x 66PH PE 11.5 16.4 22.0 13.0" 763VT 64VT x 64PA PE 12.1 15.0 21.0 13.0" 764VT 67VT x 67PD PE 10.0 15.0 20.0 15.0" 767VT 68VT X 68PB PE 9.5 14.1 19.1 12.0" 768VT *Be certain your air supply is sufficient to operate Nozzle No. 59ASS 59BSS 59CSS 63ASS 63BSS 63CSS 65SS 66SS 67SS 68SS nozzles selected. Orifice Size.171.218.281.040.046.052.059.070.086.110 PE, Pressure feed, external. SE, Siphon feed, external. PI, Pressure feed, internal. VT, Tungsten Carbite Fluid Nozzles. Tungsten Carbite Air. Nitralloy Air Nozzle.

TYPE OF FLUID TO BE SPRAYED CONCRETE CURING COMPOUNDS MULTICOLOR PAINTS TEFLONS HAMMERS WRINKLE ENAMELS ZINC RICH COATINGS SPATTER VEILING DISTRESS NOZZLE AND NEEDLE SELECTION CHART FOR 95A and 95AV AUTOMATIC GUNS (cont.) CFM AT * MAX. FLUID x AIR NOZZLE 30 50 70 PATTERN FLUID NOZZLES TYPE PSI PSI PSI AT 8" NEEDLE 63SS x 200 PI 3.1 5.2 6.4 15.0" 765 67SS x 206 PI 6.0 9.5 13.0 18.0" 767 68SS x 206 PI 6.2 9.8 13.2 20.0" 768 66SS x 200 PI 3.1 5.2 12.0" 765 67SS x 206 PI 6.0 9.5 15.0" 767 63ASS x 63PB PE 9.0 14.3 20.0 10.0" 763A 63BSS x 63PR PE 9.5 15.5 19.5 15.0" 763A 66SS x 66SD SE 7.9 12.1 7.0" 765 63CSS x 63PB PE 9.0 14.3 14.0" 763A 66SS x 63PB PE 9.0 14.3 14.0" 765 66SS x 66SD SE 7.9 12.1 7.0" 765 63CSS x 63PB PE 9.0 14.3 20.0 10.0" 763A 66SS x 63PB PE 9.0 14.3 20.0 10.0" 765 66SS x 67PD PE 12.0 18.0 24.0 15.0" 765N 67VT x 67PB PE 9.5 14.1 19.1 12.0" 767VT 66SS x 66PD PE 3 at 15 PSI 765 794SS x 793 PE 3 at 17 PSI 794 794SS x 797 PE 3 at 15 PSI 794 *Be certain your air supply is sufficient to operate Nozzle No. 59ASS 59BSS 59CSS 63ASS 63BSS 63CSS 65SS 66SS 67SS 68SS nozzles selected. Orifice Size.171.218.281.040.046.052.059.070.086.110 PE, Pressure feed, external. SE, Siphon feed, external. PI, Pressure feed, internal. VT, Tungsten Carbite Fluid Nozzles. Tungsten Carbite Air. Nitralloy Air Nozzle. 95A GUN 6469-1900-7...95A GUN 62SS-63PB 6469-2500-7...95A GUN 63ASS-63PB 6469-2800-7...95A GUN 63BSS-63PB 6469-3100-7...95A GUN 63CSS-63PB 6469-4307-9...95A GUN 66SS-66SD 6469-4308-8...95A GUN 66SS-66SK 6469-5111-5...95A GUN 68SS-68PB 6469-8219-1...95A GUN 59CSS-262 STANDARD PART NUMBERS for 95A and 95AV GUNS with Fluid Nozzles, Air Caps and Needles Included. NOTE See pgs. 11-13 for 95A fluid nozzles, air nozzles and needle ordering information. (95AV set-ups appear below.) 95AV GUN 6487-3206-3...95AV GUN 63CVT-66PH 6487-3603-5...95AV GUN 64VT-64PA 6487-4909-5...95AV GUN 67VT-67PB 6487-4909-9...95AV GUN 67VT-67PD 6487-5211-5...95AV GUN 68VT-68PB 95AV NOZZLE SET-UPS (95A Nozzle set-ups shown on pages 12-13) TUNGSTEN CARBITE CARBITE TIP CARBITE TIP CARBITE TIP FLUID NOZZLE FLUID NOZZLE FLUID NEEDLE FLUID NEEDLE COMPATIBLE DESIGNATION PART NUMBER DESIGNATION PART NUMBER AIR CAPS AIR CAP PART NUMBER 63CVT 45-6332 763VT 47-762 63P 46-6000 63PB 46-6002 63PR 46-6079 200 46-2200 Tip and 54-1583 Base, 54-1584 Ring 64VT 45-6402 764VT 47-764 64PA 46-6007 67VT 45-6702 767VT 47-767 67PB 46-6026 67PD 46-6028 206 46-2206 Tip and 54-1583 Base, 54-1584 Ring 706 46-2013 Tip and 54-372 Base 709SS 46-2020 Tip and 54-372 Base 713 46-2025 Tip and 54-372 Base 797 46-156 Tip and 54-372 Base 68VT 45-6802 768VT 47-769 68PB 46-6032 201 46-2201 Tip and 54-1583 Base, 54-1584 Ring 206 46-2206 Tip and 54-1583 Base, 54-1584 Ring 706 46-2013 Tip and 54-372 Base 709SS 46-2020 Tip and 54-372 Base 713 46-2025 Tip and 54-372 Base 797 46-156 Tip and 54-372 Base 9

Binks Model 95A, 95AV AUTOMATIC AIR SPRAY GUN ASSEMBLY DRAWING 47 44 45 9 7 10 12 13 11 8 15 16 14 22 46 18 21 6 20 19 56 5 17 27 4 26 3 25 24 2 37 23 30 1 35 29 38 39 53 36 28 34 42 41 52 Double Male Nipple (32) and Set Screw (46) are for installations requiring separate fan and atomizing air control. (See pg. 4) Items 31, 32 and 46 are packaged loose. 32 43 55 40 32 54 33 49 48 50 51 Item 42 must be compressed and inserted inside Item 41 for proper seal function. Accessory item. Order separately. 55 55 95AV FLUID INLET REFERENCE KIT 54-4511 31 10

ITEM PART NO. NO. DESCRIPTION QTY. 1 * AIR CAP ASSEMBLY... 1 2 * FLUID NOZZLE... 1 3 54-918 SEALING RING... 1 4 54-4215 HEAD INSERT... 1 5 54-4206 95A GUN BODY ASSEMBLY... 1 6 20-1359 SQ. HD. BOLT 5/16-18 X 3/4... 1 7 54-3720 SIDE PORT CONTROL ASSEMBLY. 1 8 54-3721 CONTROL SPINDLE... 1 9 31-258 RETAINING PIN... 1 10 31-256 STUFFING BOX... 1 11 31-259 INNER WASHER... 3 12 20-3620 O-RING... 1 13 31-241 CONTROL SPRING... 1 14 54-4269 JAM NUT... 1 15 54-3987 PLUG... 1 16 54-3988 PLUG 1/16" NPT... 2 17 20-5286 O-RING... 1 18 54-3706 PISTON ASSEMBLY... 1 19 54-3729 SEAL... 1 20 54-3722 PISTON... 1 21 20-4511 O-RING... 1 22 * NEEDLE... 1 23 20-3515 O-RING... 1 24 54-3713 NEEDLE BODY... 1 25 54-3709 NEEDLE LOCKING NUT... 1 26 54-3719 SPRING Needle Return... 1 27 54-1876 SPRING Piston Return... 1 28 54-3708 END CAP... 1 29 54-3732 LOCKNUT... 1 30 54-3731 CONTROL KNOB... 1 31 54-3715 STOP SCREW... 1 ITEM PART NO. NO. DESCRIPTION QTY. 60 54-1584 RETAINING RING... 1 61 54-1583 NOZZLE TIP BASE ASSEMBLY... 1 62 54-2065 RING... 1 63 659 NEEDLE ASSEMBLY... 1 PARTS LIST (When ordering, please specify Part No.) OPTIONAL NOZZLE SET-UPS (When ordering, please specify Part No.) ITEM PART NO. NO. DESCRIPTION QTY. 32 71-28 DOUBLE MALE NIPPLE 1/8 NPT x 1/4 NPS... 2 33 54-4208 FLUID INLET Recirculating (Optional).. 1 34 54-4210 FLUID INLET (95A Gun)... 1 35 54-4264 GLAND ADAPTER (95A Gun)... 1 36 54-4265 NEEDLE SEAL (95A Gun)... 1 37 54-4266 SEAL BACKUP (95A Gun)... 1 38 54-4267 SPRING (95A Gun)... 1 39 54-4263 PACKING NUT (95A Gun)... 1 40 57-13 DOUBLE MALE NIPPLE 1/4 NPT x 1/4 NPS... 1 41 54-3716 AIR VALVE GLAND ASSEMBLY... 1 42 20-3859 O-RING... 1 43 54-3986 PLUG 1/8-27 NPT... 1 44 54-4213 WRENCH (Optional)... 1 45 82-469 GUN BRUSH... 1 46 20-2141 SET SCREW 1/4"-20 UNC... 1 47 54-3871 GUNNERS MATE... 1 48 54-4568 FLUID INLET (95AV Gun)... 1 49 20-2227 O-RING (95AV Gun)... 1 50 54-4531 SPACER (95AV Gun)... 1 51 54-4542 NUT ASSEMBLY (95AV Gun)... 1 52 54-3592 FLUID INLET SEAL... 1 53 54-4270 NEEDLE COVER... 1 54 73-24 90º S.S. CONNECTION (Optional)... 1 55 73-12 90º CONNECTION (Optional)... 3 56 54-3719 SPRING Heavy Duty (Optional)... 1 * See Air Cap, Fluid Nozzle, and Needle Selection Chart on pgs. 6-7. Part of Repair Kit 54-4225. Part of Repair Kit 54-3579. Part of Gun Body Assembly, item 5. Part of item 18. Also available separately. Accessory item. Order separately. Included in 54-4511 kit for vitreous set-up. ITEM PART NO. NO. DESCRIPTION QTY. 70 797 AIR NOZZLE... 1 71 790 STRAIGHT CORE... 1 72 794SS FLUID NOZZLE... 1 73 794 NEEDLE ASSEMBLY... 1 74 792 SPIRAL CORE... 1 75 793 AIR NOZZLE... 1 INTERNAL MIX HEAVY MATERIAL NOZZLES (OPTIONAL) Air Nozzle 200, 201, 206 Nitralloy 62 60 61 63 SPECIAL EFFECTS NOZZLES (OPTIONAL) 70 71 DISTRESSING VEILING 72 Fluid Nozzle (see pg. 6) 59ASS, 59BSS, 59CSS Air Nozzle (see pg. 6) 244, 250, 252, 262 75 74 73 11

GUN DIMENSIONS 4" 1/2" Diameter Hole for Gun Mate Bracket 4" 2" 7" 2" Approximate Weight 1.2 lbs. ACCESSORIES (Optional) MOUNTING BRACKETS Use for automatic guns. Adjustable to any position. 18" bracket arm. 1" diameter bracket clamp hole for attachment to facility hardware. 1" Diameter 54-380 Steel bracket for automatic guns. Shipping weight: 5 lbs. 54-551 Aluminum bracket for automatic guns on reciprocators. Shipping weight: 3 lbs. Part Sheet 1185. 1/2" Dia. Gun Mounting GUN COVER ASSEMBLY 54-3691 Use over the 95A and 95AV automatic spray guns to protect them from overspray. Drawing at right shows gun cover with 95A automatic spray gun. (Package of 20 covers). Gun Cover 95A NOZZLE SET-UPS STAINLESS STAINLESS STAINLESS STAINLESS STEEL FLUID STEEL FLUID STEEL FLUID STEEL FLUID NOZZLE NOZZLE PART NEEDLE NEEDLE PART COMPATIBLE AIR CAP DESIGNATION NUMBER DESIGNATION NUMBER AIR CAPS PART NUMBER 62SS 45-6201 762 47-760 63P 46-6000 63PB 46-6002 63PR 46-6079 66PH 46-6016 66SD 46-6020 66SD-3 46-6092 66SK 46-6082 63ASS 45-6311 763A 47-763 63P 46-6000 63PB 46-6002 63PR 46-6079 66PH 46-6016 66SD 46-6020 66SD-3 46-6092 66SK 46-6082 Continued on next page. 12

95A NOZZLE SET-UPS (cont.) STAINLESS STAINLESS STAINLESS STAINLESS STEEL FLUID STEEL FLUID STEEL FLUID STEEL FLUID NOZZLE NOZZLE PART NEEDLE NEEDLE PART COMPATIBLE AIR CAP DESIGNATION NUMBER DESIGNATION NUMBER AIR CAPS PART NUMBER 63BSS 45-6321 763A 47-763 63P 46-6000 63PB 46-6002 200 46-2200 Tip and 54-1583 Base, 54-1584 ring 201 46-220 Tip and 54-1583 Base, 54-1584 Ring 63PR 46-6079 63CSS 45-6331 763A 47-763 63P 46-6000 63PB 46-6002 200 46-2200 Tip and 54-1583 Base, 54-1584 Ring 201 46-2201 Tip and 54-1583 Base, 54-1584 Ring 66SS 45-6601 765 47-765 63P 46-6000 63PB 46-6002 63PR 46-6079 66PD 46-6013 66PE 46-6014 66PH 46-6016 66R 46-6041 66S 46-6018 66SD 46-6020 66SD-3 46-6092 66SK 46-6082 67SS 45-6701 767 47-766 67PB 46-6101 67PD 46-6028 706 46-2013 Tip and 54-372 Base 709SS 46-2020 Tip and 54-372 Base 713 46-2025 Tip and 54-372 Base 797 46-156 Tip and 54-372 Base 68SS 45-6801 768 47-768 68PB 46-6032 201 46-2206 Tip and 54-1583 Base, 54-1584 Ring 206 46-2206 Tip and 54-1583 Base, 54-1584 Ring 706 46-2013 Tip and 54-1583 Base, 54-1584 Ring 709SS 46-2020 Tip and 54-372 Base 713 46-2025 Tip and 54-372 Base 797 46-156 Tip and 54-372 Base 59ASS 45-5911 759 47-75900 244 46-2244 Tip and 54-2065 Ring 59BSS 45-5912 759 47-75900 250 46-2250 Tip and 54-2065 Ring 252 46-2252 Tip and 54-2065 Ring 59CSS 45-5913 759 47-75900 262 46-2262 Tip and 54-2065 Ring L6SS 45-6605 759 47-75900 63P 46-6000 63PB 46-6002 66PD 46-6013 66PE 46-6014 66PH 46-6016 66S 46-6018 66SK 46-6082 13

14 NOTES

NOTES 15

ITW Industrial Finishing Binks has authorized distributors throughout the world. For technical assistance or the distributor nearest you, see listing below. U.S./Canada Technical Service Office: 195 Internationale Blvd., Glendale Heights, IL 60139 Toll-Free Telephone: 1-888-992-4657 (U.S.A. and Canada only) Toll-Free Fax: 1-888-246-5732 Binks Worldwide Sales and Service Listing: www.binks.com WARRANTY This product is covered by Binks 1 Year Limited Warranty. 77-2641R-8 Revisions: (P1) Corrected text; (P9) Updated Standard part Number chart; (P11) Updated Parts List. 3/08 2008 Illinois Tool Works Inc. All rights reserved. Printed in U.S.A.