801 Avenida Acaso, Camarillo, Ca. 93012 (805) 494-0622 www.sdcsecurity.com E-mail: service@sdcsecurity.com INSTALLATION INSTRUCTIONS E300 SERIES MAGNETIC CABINET/DISPLAY CASE LOCK The E300 Series magnetic lock is mounted to the underside of the cabinet housing or vertically inside the cabinet. Electrical Specifications: Dual Voltage 12 or 24VDC Power Consumption 360mA@12VDC 180mA@24VDC LS Lock Status Sensor SPDT, 250mA@30VDC Select jumper position for 12VDC or 24VDC. Connect power to magnetic lock. 24VDC 12VDC Voltage Jumper 1 2 + - Power Supply N/O CLOSED WITH POWER & DOOR CLOSED COM N/C OPEN WITH POWER & DOOR CLOSED } Lock Status Switch A/C MAINS POWER SUPPLY + - 12VDC or 24VDC SWITCH or ACCESS CONTROL Test operation. After verifying proper operation, tighten all screws as shown. Install anti-tamper plugs over socket screws using a soft hammer to avoid damage to the housing. P:\INSTALLATION INST\Electromagnetic Locks\EXCEL\INST-E300.vsd REV B 06-15 Page 1 Any suggestions or comments to this instruction or product are welcome. Please contact us through our website or email engineer@sdcsecurity.com
STEP 1 FOLD TEMPLATE ALONG DOTTED LINE. PLACE TEMPLATE AGAINST CABINET DOOR AND FRAME. DRILL HOLES AS INDICATED ON TEMPLATE. STEP 2 MOUNT THE ARMATURE PLATE TO DOOR USING (1 ) RUBBER WASHER SANDWICHED BETWEEN (2) STEEL WASHERS (THE RUBBER WASHER AND (2) STEEL WASHERS ARE INSTALLED ON THE MOUNTING BOLT BETWEEN THE ARMATURE PLATE AND DOOR). STEP 3 INSTALL THE MOUNTING PLATE ADJUST THE MOUNTING PLATE SO THAT IT AND THE ARMATURE FORM A RIGHT ANGLE. INSTALL THE REMAINING MOUNTING SCREWS. STEP 4 INSTALL MAGNET TO MOUNTING PLATE. CAUTION: The lock body must be held in place until secured with mounting screws. Secure socket head screws provided inside the housing at each end. Start screws into threads carefully to avoid stripping the threads. Check alignment and tighten screws. Pull wires through frame, mounting plate and magnet housing P:\INSTALLATION INST\Electromagnetic Locks\EXCEL\INST-E300.vsd REV B 06-15 Page 2
3580 Willow Lane, Westlake Village, CA 91361-4921 (805) 494-0622 Fax: (805) 494-8861 www.sdcsecurity.com E-mail: service@sdcsecurity.com INSTALLATION INSTRUCTIONS E6200 SERIES MAGNETIC LOCK The E6200 Series magnetic lock is mounted to the underside of the header, on the stop side of the door. Frame Mounting Screws Armature Outswing Electrical Instructions: Use properly fused U. L. Listed Power Supply Do not install a diode in parallel with any magnetic lock. A diode will cause a delay when releasing the door and residual magnetism to occur. Although SDC recommends the use of a DC power supply, a transformer with an adjacent mounted full wave bridge rectifier may be used. A significant drop will occur when using a full wave bridge rectifier. Any low voltage condition will cause erratic operation of the optional board sensor. When using a full wave bridge rectifier all access controls and/or release contacts must be located between the EMlock and rectifier to ensure quick release. P:\INSTALLATION INST\Electromagnetic Locks\EXCEL\INST-E6200.vsd REV - 07-10 Page 1 Electrical Specifications: Dual Voltage Power Consumption 12 or 24VDC.250mA@12VDC.125mA@24VDC DS Door Status Sensor SPDT, 500mA@30VDC LS Lock Status Sensor SPDT, 2A@30VDC Any suggestions or comments to this instruction or product are welcome. Please contact us through our website or email engineer@sdcsecurity.com
1. Fold template as indicated on dotted line. For single doors locate template against the door and header on the lock jamb side of the frame. 2. Mark and drill holes as indicated by the template. STEPS 1 & 2 3. Mount armature to door. STEP 3 4. WIRING DETAILS: * ACCESS CONTROL(S) (+) To Properly Fused DC Power source (-) (+) RED BLU BLK BRN (-) 12VDC CONFIGURATION E6200 EMLOCK 12VDC @.250 Amps BOND SENSOR (BAS) WIRING WIRE COLOR CONTACT YEL GRN ORG N/O COM N/C DESCRIPTION GOOD BOND COMMON NO/POOR BOND * ACCESS CONTROL(S) (+) (+) RED BLU To Properly BLK Fused DC Power BRN source (-) (-) 24VDC CONFIGURATION E6200 EMLOCK 24VDC @.125 Amps DOOR POSITION SENSOR (DPS) WIRING WIRE COLOR CONTACT WHT GRY VIO N/O COM N/C DESCRIPTION ACTIVATE WHEN DOOR OPEN COMMON ACTIVATE WHEN DOOR CLOSED P:\INSTALLATION INST\Electromagnetic Locks\EXCEL\INST-E6200.vsd REV - 07-10 Page 2
5. Install magnet onto the header with the magnetic face towards the door side of the stop. Assure that the magnet and armature line up properly, then tighten down ALL mounting screws. STEP 5 6. Test operation. When all is operating properly, install antitamper plugs over socket head screws using a soft hammer to avoid damage to the housing. P:\INSTALLATION INST\Electromagnetic Locks\EXCEL\INST-E6200.vsd REV - 07-10 Page 3
MODEL E6200 #1/4-20 x 2 8.00 (203.20) 7.20 (182.88) 1.00 (25.40) C L 2.25 (67.15).50 (12.70) 4.00 (101.60).375 (9.525) 6.00 (152.40) 2.25 (67.15).75 (19.05) 1.84 (46.74) 2.875 (73.03).64 (16.26) 2.75 (69.85) P:\INSTALLATION INST\Electromagnetic Locks\EXCEL\INST-E6200.vsd REV - 07-10 Page 4
801 Avenida Acaso, Camarillo, Ca. 93012 (805) 494-0622 Fax: (805) 494-8861 www.sdcsecurity.com E-mail: service@sdcsecurity.com INSTALLATION INSTRUCTIONS E1200 SERIES MAGNETIC LOCK Interlocking Mounting Plate Quick Mount Interlocking Mounting Assembly Frame Mounting Screws Armature Outswing Electrical Instructions: Use properly fused U. L. Listed Power Supply Do not install a diode in parallel with any magnetic lock. A diode will cause a delay when releasing the door and residual magnetism to occur. Although SDC recommends the use of a DC power supply, a transformer with an adjacent mounted full wave bridge rectifier may be used. A significant drop will occur when using a full wave bridge rectifier. Any low voltage condition will cause erratic operation of the optional board sensor. Electrical Specifications: Dual Voltage Power Consumption 12 or 24VDC.500mA@12VDC 250mA@24VDC DS Door Status Sensor SPDT, 500mA@30VDC LS Lock Status Sensor SPDT, 2A@30VDC When using a full wave bridge rectifier all access controls and/or release contacts must be located between the EMlock and rectifier to ensure quick release. P:\INSTALLATION INST\Electromagnetic Locks\EXCEL\INST-E1200.vsd REV A1 04-11 Page 1 Any suggestions or comments to this instruction or product are welcome. Please contact us through our website or email engineer@sdcsecurity.com
1. Inspect the frame header to determine if mounting accessories are required (refer to page 4). 2. Fold template as indicated on dotted line. For single doors locate template against the door and header on the lock jamb side of the frame. 3. Mark and drill holes as indicated by the template. STEPS 2 & 3 4. Mount armature to door. STEP 4 5/16-18 SOC HD SCREW WITH 3/16 (5MM) ALLEN HEX STEEL WASHER 2X REINFORCEMENT TUBE 5/8 DRILL 1-3/4 HOLLOW METAL DOOR ARMATURE RUBBER WASHER 1/2 DRILL SEXNUT HOLLOW METAL DOOR From Sexnut side of door, drill exactly 1/2 hole thru one metal thickness only. From Armature side of door, drill 5/8 hole to insert reinforcement tube. Press in sexnut and reinforcement tube all the way and mount armature to door using hardware provided. 5. Install magnet onto the header with the magnetic stripes towards the door side of the stop. Assure that the magnet and armature line up properly, then tighten down ALL mounting screws. STEP 5 P:\INSTALLATION INST\Electromagnetic Locks\EXCEL\INST-E1200.vsd REV A1 04-11 Page 2
6. Holding the magnet housing at each end, engage the entire length of the interlock detail, by pushing towards the door. Tap with a soft hammer to ensure proper alignment and engagement. CAUTION: The lock body must be held in place until secured with mounting screws. Secure socket head screws provided inside the housing at each end. Start screws into threads carefully to avoid stripping the threads. Check alignment and tighten screws. Pull wires through frame, mounting plate and magnet housing STEP 6 7. Select jumper position for 12VDC or 24VDC. Connect power to magnetic lock. Lock Status Switch (Relay) Power Supply 1 + 2-3 NO 4 C 5 NC A/C MAINS POWER SUPPLY + - 12VDC or 24VDC SWITCH or ACCESS CONTROL Door Position Sensor 6 NO 7 C 8 NC W R GB ATTACH THE RED SIDE OF THE CONNECTOR HERE FOR A GREEN LED ENERGIZED & SECURE (RED=ENERGIZED & UNSECURE) G BR LED RED GRN Voltage Jumper ATTACH THE GREEN SIDE OF THE CONNECTOR HERE FOR A RED LED ENERGIZED AND UNSECURE (GREEN=ENERGIZED & SECURE) 12VDC 24VDC Door Position Sensor (Reed switch) NC COM RED (open with door closed) BLACK GREEN (closed with door closed) NO 8. Test operation. When all is operating properly, tighten all screws as shown. Install security pins and screws as shown. Install anti-tamper plugs over socket head screws using a soft hammer to avoid damage to the housing. P:\INSTALLATION INST\Electromagnetic Locks\EXCEL\INST-E1200.vsd REV A1 04-11 Page 3
MOUNTING ACCESSORIES: STOP FILLER PLATE EF02 Inches: 10.5" L x 0.5" H x 0.75" D mm: 266 L x 12.7 H x 19 D ANGLE BRACKET E12L Inches: 10.5" L x 0.5" H x 0.75" D mm: 266 L x 12.7 H x 19 D ADJUSTABLE ANGLE BRACKET E12A For use with Model E1200 Series GLASS DOOR ARMATURE BRACKET E12U For use with Model E600 Series Field adjustable for glass thickness TOP JAMB MOUNTING BRACKET E12Z For use with Model E1200 Series Supplied Mounting Hardware To maintain surface plating from corrosion: Do not touch the lock face with your hands. Clean lock face with Scotch-Brite pad by 3M (do not use sandpaper). Apply a thin film of rust inhibitor (LPS-3) on lock face. Repeat application on armature plate. P:\INSTALLATION INST\Electromagnetic Locks\EXCEL\INST-E1200.vsd REV A1 04-11 Page 4
801 Avenida Acaso, Camarillo, Ca. 93012 (805) 494-0622 Fax: (805) 494-8861 www.sdcsecurity.com E-mail: service@sdcsecurity.com INSTALLATION INSTRUCTIONS E600 SERIES MAGNETIC LOCK The E600 Series magnetic lock is mounted to the underside of the header, on the stop side of the door. An inswing mounting kit (optional) can be used when mounting on the hinge side of the door. Interlocking Mounting Plate Quick Mount Interlocking Mounting Assembly Frame Mounting Screws Armature Outswing Electrical Instructions: Use properly fused U. L. Listed Power Supply Do not install a diode in parallel with any magnetic lock. A diode will cause a delay when releasing the door and residual magnetism to occur. Although SDC recommends the use of a DC power supply, a transformer with an adjacent mounted full wave bridge rectifier may be used. A significant drop will occur when using a full wave bridge rectifier. Electrical Specifications: Dual Voltage Power Consumption 12 or 24VDC 500mA@12VDC 250mA@24VDC DS Door Status Sensor SPDT, 500mA@30VDC LS Lock Status Sensor SPDT, 2A@30VDC Any low voltage condition will cause erratic operation of the optional board sensor. When using a full wave bridge rectifier all access controls and/or release contacts must be located between the magnetic lock and rectifier to ensure quick release. P:\INSTALLATION INST\Electromagnetic Locks\EXCEL\INST-E600.vsd REV A1 04-11 Page 1 Any suggestions or comments to this instruction or product are welcome. Please contact us through our website or email engineer@sdcsecurity.com
1. Inspect the frame header to determine if mounting accessories are required (refer to page 4). 2. Fold template as indicated on dotted line. For single doors locate template against the door and header on the lock jamb side of the frame. 3. Mark and drill holes as indicated by the template. STEPS 2 & 3 4. Mount armature to door. STEP 4 STEEL WASHER 2X REINFORCEMENT TUBE 1-3/4 HOLLOW METAL DOOR 5/16-18 SOC HD SCREW WITH 3/16 (5MM) ALLEN HEX 5/8 DRILL ARMATURE RUBBER WASHER 1/2 DRILL SEXNUT HOLLOW METAL DOOR From Sexnut side of door, drill exactly 1/2 hole thru one metal thickness only. From Armature side of door, drill 5/8 hole to insert reinforcement tube. Press in sexnut and reinforcement tube all the way and mount armature to door using hardware provided. 5. Install mounting plate to header with the interlock detail away from the door side of the stop. Loosely fasten screws through adjustment slot as shown. Assure that the mounting plate and armature line up properly, then tighten down ALL mounting screws. STEP 5 P:\INSTALLATION INST\Electromagnetic Locks\EXCEL\INST-E600.vsd REV A1 04-11 Page 2
6. Holding the magnet housing at each end, engage the entire length of the interlock detail, by pushing towards the door. Tap with a soft hammer to ensure proper alignment and engagement. CAUTION: The lock body must be held in place until secured with mounting screws. Secure socket head screws provided inside the housing at each end. Start screws into threads carefully to avoid stripping the threads. Check alignment and tighten screws. Pull wires through frame, mounting plate and magnet housing STEP 6 7. Select jumper position for 12VDC or 24VDC. Connect power to magnetic lock. 1 2 3 4 5 + - NO C NC Power Supply Lock Status Switch Door Position Sensor (Reed switch) NC COM RED (open with door closed) BLACK GREEN (closed with door closed) NO LED Voltage Jumper 24VDC 12VDC A RED LED INDICATES ENERGIZED & UNSECURED (GREEN=ENERGIZED & SECURE) A/C MAINS POWER SUPPLY + - 12VDC or 24VDC SWITCH or ACCESS CONTROL 8. Test operation. When all is operating properly, tighten all screws as shown. Install anti-tamper plugs over socket head screws using a soft hammer to avoid damage to the housing. P:\INSTALLATION INST\Electromagnetic Locks\EXCEL\INST-E600.vsd REV A1 04-11 Page 3
MOUNTING ACCESSORIES: STOP FILLER PLATE EF02 Inches: 10.5" L x 0.5" H x 0.75" D mm: 266 L x 12.7 H x 19 D May be field cut for use with E600 ANGLE BRACKET E12L Inches: 10.5" L x 0.5" H x 0.75" D mm: 266 L x 12.7 H x 19 D May be field cut for use with E600 ADJUSTABLE ANGLE BRACKET E6A For use with Model E600 Series GLASS DOOR ARMATURE BRACKET E6U For use with Model E600 Series Field adjustable for glass thickness TOP JAMB MOUNTING BRACKET E6Z For use with Model E600 Series Supplied Mounting Hardware To maintain surface plating from corrosion: Do not touch the lock face with your hands. Clean lock face with Scotch-Brite pad by 3M (do not use sandpaper). Apply a thin film of rust inhibitor (LPS-3) on lock face. Repeat application on armature plate. P:\INSTALLATION INST\Electromagnetic Locks\EXCEL\INST-E600.vsd REV A1 04-11 Page 4
801 Avenida Acaso, Camarillo, Ca. 93012 (805) 494-0622 www.sdcsecurity.com E-mail: service@sdcsecurity.com INSTALLATION INSTRUCTIONS E300 SERIES MAGNETIC CABINET/DISPLAY CASE LOCK The E300 Series magnetic lock is mounted to the underside of the cabinet housing or vertically inside the cabinet. Electrical Specifications: Dual Voltage 12 or 24VDC Power Consumption 360mA@12VDC 180mA@24VDC LS Lock Status Sensor SPDT, 250mA@30VDC Select jumper position for 12VDC or 24VDC. Connect power to magnetic lock. 1 2 + - Power Supply Voltage Jumper 24VDC 12VDC Lock Status Switch BLACK COM NC NO RED (open with power and door closed) GREEN (closed with power and door closed) A/C MAINS POWER SUPPLY + - 12VDC or 24VDC SWITCH or ACCESS CONTROL Test operation. After verifying proper operation, tighten all screws as shown. Install anti-tamper plugs over socket screws using a soft hammer to avoid damage to the housing. P:\INSTALLATION INST\Electromagnetic Locks\EXCEL\INST-E300.vsd REV A 04-11 Page 1 Any suggestions or comments to this instruction or product are welcome. Please contact us through our website or email engineer@sdcsecurity.com
STEP 1 FOLD TEMPLATE ALONG DOTTED LINE. PLACE TEMPLATE AGAINST CABINET DOOR AND FRAME. DRILL HOLES AS INDICATED ON TEMPLATE. STEP 2 MOUNT THE ARMATURE PLATE TO DOOR USING (1 ) RUBBER WASHER SANDWICHED BETWEEN (2) STEEL WASHERS (THE RUBBER WASHER AND (2) STEEL WASHERS ARE INSTALLED ON THE MOUNTING BOLT BETWEEN THE ARMATURE PLATE AND DOOR). STEP 3 INSTALL THE MOUNTING PLATE ADJUST THE MOUNTING PLATE SO THAT IT AND THE ARMATURE FORM A RIGHT ANGLE. INSTALL THE REMAINING MOUNTING SCREWS. STEP 4 INSTALL MAGNET TO MOUNTING PLATE. CAUTION: The lock body must be held in place until secured with mounting screws. Secure socket head screws provided inside the housing at each end. Start screws into threads carefully to avoid stripping the threads. Check alignment and tighten screws. Pull wires through frame, mounting plate and magnet housing P:\INSTALLATION INST\Electromagnetic Locks\EXCEL\INST-E300.vsd REV A 04-11 Page 2