AG20-IV / AG1-IV ROTARY FLEX WING MOWER ARCHIVE BOOK - I By Serial Number / Production Book 1 = Sep. 1989 s/n AG20-0100 s/n AG20-01299 AG20-IV Model - 20' Flex Wing Rotary AG1-IV Model - 1' Model (Not Available till after ) COMPLETE PARTS LISTING BOOK 1 Archive Book 1 of 2 Part No. 02979200 ALAMO INDUSTRIAL 102 E. Walnut Seguin, Texas 781 2002 Edition 80-72-1 An Alamo Group Company 2002 Alamo Group Inc.
NOTES
INDEX - AG20-IV (20' Flex Wing Rotary) ITEM PAGE NO. INTRODUCTION Parts Section Introduction... 1 AXLE Center Axle... 6-7-8-9 Wing Axle... 10-11-12-1 BLADES & CARRIER Pan Carriers... 28 Bar Carriers... 70-71 CHAINGUARDS Front & Rear... --6-7 CLUTCHES Intermeadiate & Wing Drivelines... 8-9 CONTROL RODS Leveling Front Rear... 1 Tongue Clevis Level... DECALS All... 68 thru 72 DECK Center & Wing Section... 2- DEFLECTORS Front & Rear... 0-1-2- DRIVELINES PTO 0 RPM & 1000 RPM... 0-1-2- Intrmeadiate 0 & 1000 RPM... - Wing 0 RPM & 1000 RPM... 6-7 GEARBOX Divider, 0 RPM & 1000 RPM... 16-17 Center Section... 0 RPM... 18-19 1000 RPM... 20-21 RH Wing Section... 0 RPM & 1000 RPM... 22-2 LH Wing Section 0 RPM & 1000 RPM... 2-2 2002 Alamo Group Inc. INDEX - 1 Continued Next Page
INDEX - AG20-IV (20' Flex Wing Rotary) ITEM PAGE NO. GEARBOX SHIELD Divider & Center Blade Box... 26 HYD. CYL. Center Axle Lift (Standard Axle Lift)... 2- Center Axle Lift (Optional Level Lift)... Wing Lift & Fold, LH & RH... -6 HYD. HOSE STAND All Hose Stands... 1 HYD. Schematic Standard Lift & Fold... 8-9 Optional Lift & Fold... 60-61 HYD. VALVE Closed Center... 8-9 Open Center... 0-1 PARKING JACK Tongue Lift Jack... SAFETY CHAIN Tongue Safety Connection... SKID SHOES Center & Wing... 2- SLIP CLUTCHES Pull or Lift Type... 8-9 TONGUE Tongue & Tongue Control Rod... WHEEL HUBS Center & Wing Axle... 62-6 WHEELS Center & Wings,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,... 6 WINCH & STAND Center & Wings,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,... 66-67 2002 Alamo Group Inc. INDEX - 2
AG20-IV Rotary ARCHIVE BOOK INTRODUCTION - VOLUME I The AG20-IV Archive Book is a complete listing of Parts from the first Unit the Present in two volumes, Volume I from Sep. 1989 (s/n AG20-0100 Start) & Volume II from Aug. 199 Current. The Production Dates, Serial Numbers, Special Notes and Descriptions are furnished help find Replacement Parts. Dimension (if listed) are for Identification of Parts and MAY NOT be Manufacturing Specification, Your measurements may vary some from dimensions listed. Some Parts may be changed and be different than parts listed. Some Modification may be required when replacing older parts. Match S/N's listed in the rear of this Book with the Ship Dates listed at the p of each Parts Page. This is because of the wide range of Model sizes using these S/N's Beginning Production Date PAGE EXAMPLE Beginning S/N Sep. 1989 DECK COMPONENTS S/N AG20-0100 S/N AG20-01160 Ending Production Date Componets Listed This Page Ending S/N For ordering parts the following instructions are offered help eliminate delay 1. The purchase order must include the Name, Address (Ship Street Address) of the Person / Organization ordering the parts. Who / How Parts should be Billed. Name and Phone Number of a Contact Person at your end. 2. The Purchase Order must list clearly the correct Part Number of Part. Quantity of each Part wanted, Complete and correct Description of each Part. All Parts will be shipped as requested depending on availability and/or reasonability of request carrier / method.. Alamo Industrial reserves the right substitute parts where applicable and change prices Without prior notice. Alamo Industrial also reserves the right Ship Parts the most Reasonable way as determined by Alamo Industrial.. Some Parts are unlisted items, which are special production items not normally scked or built for a limited / special use, These parts may be subject special handling or cannot be priced till ordered. Always Request a quotation for such Parts before sending a purchase order. 2002 Alamo Group Inc. Parts Section -1
Deck Components 1,1 1 11 9 10 12 19 21 20 16 18 2 6,7 6,7 20 19 21 17 18 2002 Alamo Group Inc. Parts Section -2
Deck Components Item PartNo. Qty. Description 1 0077766 1 Center Deck Wldmt, (w/o Gearbox) 2 007776 1 LH Wing Deck Wldmt, (w/o Gearbox) 007776 1 RH Wing Deck Wldmnt, (w/o Gearbox) 0811090000 2 Pin, Hinge 7A1812 2 Bolt 6 710121 Plate, Cover 7 F180 6 Nut, Wing 8 JRC180 2 Locknut 9 7A81 2 Bolt 10 7106A 2 Spring 11 0811120000 2 Spring Retainer Disk 12 JRC810 2 Locknut 1 0811110000 2 Transport Bar 1 7107B1 Retaining Pins 16 081080107 2 Skid Shoe, Center 17 0811080000 2 Skid Shoe, LH or RH Wing 18 2A8112 12 Plow Bolt 19 00001200 12 Nut, Hex 20 1B800 Washer, Plain 21 0000100 12 Lock Washer Note: The AG20-IV Archive Book is in 2 volumes, Sep 1989 Jul. is Book I and 199 and Aug. 199 Current is Book II. After July 199 this model was changed in design. The Decks, Axles, Tongue and most all the other components were changed the extent that they WOULD NOT Interchange with this older style. The Best way ID this later Design would be the Rear Axle System. The Rear Axle System is a Mechanical Level Lift design where the Center and Wing Axles are connected with adjustable turn buckles, This is allow one Cylinder (the center Axle Lift Cylinder) raise all three Axles at the same time, For this later Design See Book 2 of the AG20- IV Archive Books. DO NOT order Parts from this Book if you have a Mower built after July 199 () 2002 Alamo Group Inc. Parts Section -
Tongue And Control Rod 1,6 6,7 2 11,8 Item Part No. Qty. Description 0076080 - Tongue Asy w/o Control Rod 1* 0076079 1 Tongue Weldment 2* 6102 1 Tongue Clevis * 08110 000 2 Tongue Pivot Pin 08110000 1 Tongue Control Rod Wldmnt * 7AH12166 1 Capscrew 6* 00789 Locknut 7 7AH121620 2 Bolt 8* 00606000 2 Pin, Cotter 9* 00787 1 Flatwasher, (Not Shown) 10* JRC190 1 Locknut, (Not Shown) 11 D10 1 Decal, Draw Bar Adjust * These Items are included in Tongue Asy 2002 Alamo Group Inc. Parts Section -
Tongue And Control Rod 1 Item Part No. Qty Description 1 00766 1 Parking Jack 2002 Alamo Group Inc. Parts Section -
Jan. 1990 Axle Center S/N AG20-010 1 2 * 8 9 1 10 11 19 16 6 17 18 * 7 8 1 2 1 12 8 11 NO WASHER welded on spindle as Seal Protecr 11 2002 Alamo Group Inc. Parts Section -6
Jan. 1990 Axle Center S/N AG20-010 Item Part No. Qty. Description 00767 -- Axle Asy Center (Items 1 thru 19) 1 0811060010 1 Center Axle Bracket Weldment 2 007672 2 Axle Arm Weldment Only, Dual Spindle 081106000 2 Axle Arm Pivot Pin 6106 2 Spring Base 6107A Spring Guide 6 7106A Spring 7 61062D 2 Bushing, Spring Base Pivot 8 61062E 10 Bushing, Bronze, Axle Arm Pivot 9 0071 Cotter Pin 10 610 Tongue Pivot Pin 11* 007689 Hub Asy, W/ Components 12 6121B2 2 Spring Base Pin 1 17C1610 2 Grease Fitting 1 0202800 Bolt 1 0007200 Locknut 16 00016200 2 Bolt 17 007090 2 Locknut 18 2OBH012 Spiral Pin 19 00002701 Washer NOTE *: Item # 11 Hub Will Not have a washer welded on Spindle as a Seal protecr and this Hub has a 1" Spindle Nut. The Later Hub Will have this washer welded on Spindle and the Spindle Nut is a 7/8" Nut. 2002 Alamo Group Inc. Parts Section -7
Feb. 1990 Axle Wings S/N AG20-0106 1 2 * 1 9 19 11 16 17 10 6 1 18 * * 12 7 8 2 1 8 11 WASHER Welded Spindle as Seal Protecr 11 2002 Alamo Group Inc. Parts Section -8
Feb. 1990 Axle Wings S/N AG20-0106 Item Part No. Qty. Description 007880 -- Axle Asy Center (Items 1 thru 19) 1 00788 1 Center Axle Bracket Weldment 2 007899 2 Axle Arm w/ Dual Hubs complete 007881 2 Axle Arm Wldmnt Only (Dual Spindle) 081106000 2 Axle Arm Pivot Pin 6106 2 Spring Base 6107A Spring Guide 6 7106A Spring 7 61062D 2 Bushing, Spring Base Pivot 8 00780 Bushing, Bronze, Axle Arm Pivot 9 0071 Cotter Pin 10 610 Tongue Pivot Pin 11* 7127 Hub Asy, W/ Components 12 6121B2 2 Spring Base Pin 1 000000 2 Grease Fitting 1 0202800 Bolt 1 0007200 Locknut 16 00016200 2 Bolt 17 007090 2 Locknut 18 2OBH012 Spiral Pin 19 00002701 Washer NOTE *: Item # 11 Hub will have a washer welded on Spindle as a Seal protecr and this Hub has a 7/8" Spindle Nut. The earlier Hub Will Not have this washer welded on Spindle and the Spindle Nut is a 1" Nut 2002 Alamo Group Inc. Parts Section -9
Jan. 1990 Axle Wings S/N AG20-010 16 19 11 1 11 1 7 8 17 18 1 6 9 12 2 1 12 10 NO Washer welded Spindle as Seal Protecr 21 20 22 Standard Lift Screw Opti0onal Hydraulic Level Lift 2002 Alamo Group Inc. Parts Section -10
Jan. 1990 Axle Wings S/N AG20-010 Item Part No. Qty. Description 007670 -- Axle Asy, RH (Shown) Items 1 Thru 19 007671 -- Axle Asy, LH (Not Shown) Items 1 Thru 19 1 0811070010 1 Outboard Axle Bracket Wldmnt 2 007669 1 Single Spindle Axle Wldmnt 081107000 1 Axle Bracket Pivot Pin 081106000 1 Axle Arm Pivot Pin 007689 1 Hub w/cups & studs 6 6106 1 Spring Base 7 6107A 2 Spring Guide 8 7106A 2 Spring 9 6121B2 1 Spring Base Pin 10 61062D 1 Bushing, Spring Base Pivot 11 0299889 2 Bushing, Axle Bracket Pivot 12 00780 2 Bushing, Axle Arm Pivot 1 000000 1 Grease Fitting 1 20BH012 Spiral Pin 1 0202800 2 Capscrew 16 0007200 2 Locknut 17 00016200 1 Capscrew 18 007090 1 Locknut 19 00002701 2 Washer 20 06610000 1 Ratchet Lift Screw Asy, (std. lift only) 21* 081210100 1 Rear Lift Bracket (Level lift only) 22* 081210200 1 Adapter Plate (Level Lift only) NOTE *: Items # 21 & 22 are ONLY used if Unit is equipped with the OPTIONAL Hydraulic Level Lift System, The Hydraulic Level Lift System will not fit without these brackets. Item # Hub Will Not have a washer welded on Spindle as a Seal protecr and this Hub has a 1" Spindle Nut. The Later Hub Will have this washer welded on Spindle and the Spindle Nut is a 7/8" Nut. 2002 Alamo Group Inc. Parts Section -11
Feb. 1990 Axle Wings S/N AG20-0106 16 19 11 1 11 1 7 8 17 18 1 6 9 12 2 1 12 10 Washer welded Spindle here as Seal Protecr 21 20 22 Standard Lift Screw Opti0onal Hydraulic Level Lift 2002 Alamo Group Inc. Parts Section -12
Feb. 1990 Axle Wings S/N AG20-0106 Item Part No. Qty. Description 007889 -- Axle Asy, RH (Shown) Items 1 Thru 19 0079011 -- Axle Asy, LH (Not Shown) Items 1 Thru 19 1 007882 1 Outboard Axle Bracket Wldmnt 2 007882 1 Single Spindle Axle Wldmnt 081107000 1 Axle Bracket Pivot Pin 081106000 1 Axle Arm Pivot Pin * 7127 1 Hub w/cups & studs 6 6106 1 Spring Base 7 6107A 2 Spring Guide 8 7106A 2 Spring 9 6121B2 1 Spring Base Pin 10 61062D 1 Bushing, Spring Base Pivot 11 0299889 2 Bushing, Axle Bracket Pivot 12 00780 2 Bushing, Axle Arm Pivot 1 000000 1 Grease Fitting 1 20BH012 Spiral Pin 1 0202800 2 Capscrew 16 0007200 2 Locknut 17 00016200 1 Capscrew 18 007090 1 Locknut 19 00002701 2 Washer 20 06610000 1 Ratchet Lift Screw Asy, (std. lift only) 21* 081210100 1 Rear Lift Bracket (Level lift only) 22* 081210200 1 Adapter Plate (Level Lift only) NOTE *: Items # 21 & 22 are ONLY used if Unit is equipped with the OPTIONAL Hydraulic Level Lift System, The Hydraulic Level Lift System will not fit without these brackets. Item # Hub will have a washer welded on Spindle as a Seal protecr and this Hub has a 7/8" Spindle Nut. The earlier Hub Will Not have this washer on Spindle and the Spindle Nut is a 1" Nut 2002 Alamo Group Inc. Parts Section -1
Control Rods Leveling Rods 1 2,6,7 Item Part No. Qty. Descrption 007988 -- *Control Rod Asy Complete (Item # 1 thru 7) 1 0811100010 1 Control Rod, Long, L.H. Thread 2 00786 1 Control Rod, Short, R.H. Thread 21062 1 Adjusting Nut 61102 2 Control Rod Pin C190 1 Nut, Jam 6 0071 Pin, Cotter 7 1B1200 Washer, Plain SAE NOTE *: Qty shown is for for one Control Rod, Two Control Rod Asy required per Mower, The Tightening of these Control Rods are very Critical, they MUST tightened equal tension, To check this with mower weight on Draw Bar Strike each Control Rod with a hammer and listen the sound it makes, when the sound is the same for each control rod they are adjusted right, each time the tightness of one control rod is changed they both must be checked and re-adjusted. Shortening the length of the rods will raise the front of the mower, making them longer will lower the front of mower. 2002 Alamo Group Inc. Parts Section -1
Hydraulic Hose Brackets,, 1 2 Item Part No. Qty. Description 06110099 -- Hose Bracket Bundle, Front & Rear w/hardware 1 06110100 1 Bracket, Hose, Rear Only 2 06110100 1 Bracket, Hose, Front Only 0000800 2 Capscrew 0001000 2 Nut, Hex., 0001000 2 Washer, Lock * Bundle # - 06110099 (Includes Items #1 thru #) 2002 Alamo Group Inc. Parts Section -1
Divider Gearbox P/N 007660 (0 RPM) P/N 007698 (1000 RPM) 10 29 11 19 20 18 17 21 1 22 6 6 7 7 8 8 12 1 9 1 2 2 2 2 1 1 1 16 2 26 27 28 2 17 2 18 2002 Alamo Group Inc. Parts Section -16
Divider Gearbox P/N 007660 (0 RPM) P/N 007698 (1000 RPM) Item Part No. Qty Description 007660 1 Gearbox Asy, (0 RPM) 007698 1 Gearbox Asy, (1000 RPM) 1 00766 2 Shaft 2 007667 2 Shim 00722 2 Bearing 00722 2 Retaining Ring 00766 2 Oil Seal 6 007226 2 Oil Plug 7 00766 2 Shim 8 007228 2 Gear, 20 Tooth, (0 RPM) 00776 2 Gear, 2 Tooth, (1000 RPM) 9 007068 1 Retaining Ring 10 00720 Capscrew 11 00721 6 Spring Washer 12 00722 1 Housing 1 007668 1 Shaft 1 0072 1 Gear, 2 Tooth, (0 RPM) 0077 1 Gear, 19 Tooth, (1000 RPM) 1 0072 2 Shim 16 007070 1 Bearing, Front 17 00727 2 Retaining Ring 18 00728 2 Oil Seal 19 00729 1 Breather Plug 20 00720 1 Top Cover 21 00721 1 Bearing, Rear 22 007069 1 Gasket 2 007669 2 Retaining Ring 2 007666 2 Bearing 2 0000100 Flatwasher 26 02800 Bolt 27 0001000 Lockwasher 28 0001000 Nut 2002 Alamo Group Inc. Parts Section -17
Center Section Gearbox 0 RPM 6,7 20 2 2 2 2 22 21 9,19,26 18 16 8 6,7 10 17 1 16 27 1 28 1 29 0 Note: Blades Turn CCW 2002 Alamo Group Inc. Parts Section -18
Center Section Gearbox 0 RPM P/N 00798 CW IN - CCW OUT Item Part No. Qty. Description 00798 -- Gearbox Asy 1 00761 1 Casing 2 00761 1 Gear (2 Teeth) 00761 2 Bearing 00728 1 Oil Seal 007617 1 Shaft 6 007618 2 Internal Circlip 7 007619 2 Shim 8 007620 1 External Circlip 9 007621 1 Nut 10 007622 1 Shim 1 007626 1 Seal Protecter Shield 1 007627 1 Oil Seal 16 007628 2 Bearing 17 007629 1 Shaft 18 00760 1 Gear (16 Teeth) 19 00026200 1 Cotter Pin 20 00762 1 Shim 21 0076 1 Plug 22 0076 1 Cap 2 0076 Hex Bolt 2 00786 1 Vent Plug 2 00767 1 Cover 26 00768 1 Shim 27 029991 6 Bolt 28 0007200 6 Nut, Top Lock 29 00762 1 Washer 0 00762 1 Nut, Castle 1 16016 1 Cotterpin, Blade Carrier NOTE: This Gearbox has a Square Bolt on Top Cover & Input Gear is mounted in the front as shown in drawing 2002 Alamo Group Inc. Parts Section -19
Center Section Gearbox 1000 RPM 6,7 2 2 2 8 2,20 21 18 22 10 6,7 16 9,19 27 16 28 1,1 17 Note: Blades Turn CCW 2002 Alamo Group Inc. Parts Section -20 29,0,1
Center Section Gearbox 1000 RPM P/N 00767 CW IN - CCW OUT Item Part No. Qty Description 00767 -- Gearbox Asy. 1 00761 1 Gearbox Housing, Main 2 007692 1 Gear, Input (1 Tooth) 00761 2 Bearing 00728 1 Seal 007617 1 Shaft, Input 6 007618 2 Circlip, Internal 7 007619 2 Shim 8 007620 1 Circlip, External 9 00769 1 Nut, Slotted 10 007622 1 Shim 1 007626 1 Shield, Protective 1 007627 1 Seal 16 007628 2 Bearing 17 00769 1 Shaft, Output 18 00769 1 Gear,Output ( 2 Tooth) 19 007696 1 Cotter Pin 20 00762 1 Shim 21 0076 1 Plug, Oil Level Check 22 0076 1 Seal Cap, Rear 2 0076 Bolt 2 00786 1 Plug, Vent / Oil Fill 2 00767 1 Cover, Top 27 029991 6 Bolt 28 0007200 6 Locknut 29 00762 1 Nut, Blade Carrier Retaining 0 00762 1 Washer, Blade Carrier 1 16016 1 Cotterpin, Blade Carrier NOTE: This Gearbox has a Square Bolt on Top Cover & Input Gear is mounted in the front as shown in drawing 2002 Alamo Group Inc. Parts Section -21
RH Wing Section Gearbox 0 & 1000 RPM 6,7 2 2 2 8 2,20 21 18 22 10 6,7 16 9,19 27 16 28 1,1 17 Note: Blades Turn CCW 2002 Alamo Group Inc. Parts Section -22 29,0,1
RH Wing Section Gearbox 0 & 1000 RPM Item Part No. Qty Description 007679 -- Gearbox Asy, (0 RPM) 0076622 -- Gearbox Asy. (1000 RPM) 1 00761 1 Gearbox Housing, Main 2 0076899 1 Gear, 0 RPM Input (2 Tooth) 0076900 1 Gear, 1000 RPM Input (20 Tooth) 00761 2 Bearing 00728 1 Seal 007617 1 Shaft, Input 6 007618 2 Circlip, Internal 7 007619 2 Shim 8 007620 1 Circlip, External 9 00769 1 Nut, Slotted 10 007622 1 Shim 1 007626 1 Shield, Protective 1 007627 1 Seal 16 007628 2 Bearing 17 00769 1 Shaft, Output 18 0076900 1 Gear,0 RPM Output ( 20 Tooth) 0076899 1 Gear, 1000 RPM Output (2 Tooth) 19 007696 1 Cotter Pin 20 00762 1 Shim 21 0076 1 Plug, Oil Level Check 22 0076 1 Seal Cap, Rear 2 0076 Bolt 2 00786 1 Plug, Vent / Oil Fill 2 00767 1 Cover, Top 27 029991 6 Bolt 28 0007200 6 Locknut 29 00762 1 Nut, Blade Carrier Retaining 0 00762 1 Washer, Blade Carrier 1 16016 1 Cotterpin, Blade Carrier P/N 007679 (0 RPM) CW IN - CCW OUT P/N 0076622 (1000 RPM) CW IN - CCW OUT NOTE: This Gearbox has a Square Bolt on Top Cover & Input Gear is mounted in the front as shown in drawing 2002 Alamo Group Inc. Parts Section -2
LH Wing Section Gearbox 0 & 1000 RPM 2 8 2 2 6,7 20 21 22 2 19 9 18 6,7 10 1 16 27 16 1 1 17 29 28 0 CW IN - CW OUT 2002 Alamo Group Inc. Parts Section -2
LH Wing Section Gearbox 0 & 1000 RPM P/N 007671 (0 RPM) CW IN - CW OUT P/N 007662 (1000 RPM) CW IN - CW OUT Item Part No. Qty. Description 1 00761 1 Casing 2 0076899 1 Gear (2 Teeth-0RPM) 0076900 1 Gear (20 Teeth-1000RPM) 00761 2 Bearing 00728 1 Oil Seal 007617 1 Shaft 6 007618 2 Internal Circlip 7 007619 2 Shim 8 007620 1 External Circlip 9 00769 1 Nut 10 007622 1 Shim 1 007626 1 Proctective Shield 1 007627 1 Oil Seal 16 007628 2 Bearing 17 00769 1 Shaft 18 0076900 1 Gear (20 Teeth-0 RPM) 0076899 1 Gear (2 Teeth-100RPM) 19 007696 1 Cotter Pin 20 00762 1 Shim 21 0076 1 Plug 22 0076 1 Cap 2 0076 Hex Bolt 2 00786 1 Vent Plug 2 00767 1 Cover 27 029991 6 Bolt 28 0007200 6 Locknut 29 00762 1 Washer 0 00762 1 Nut, Castle 1 16016 1 Cotterpin, Blade Carrier NOTE: This Gearbox has a Square Bolt on Top Cover & Input Gear is mounted in the Back as shown in drawing 2002 Alamo Group Inc. Parts Section -2
Shields Divider & Center Gearbox 1 2 8 12 7 10 9 6 8 11 Item Part No Qty Descriptin 1 06610100 1 Safety Shield, Divider Gearbox 2 007016 1 Safety Shield, Center Blade Box 0076076 1 Rear Support 0000000 2 Wing Nut 007169 Bolt 6 10182000 2 Bolt 7 00011700 Lockwasher 8 00011100 Flatwasher 9 0001800 2 Nut 10 0002100 2 Flatwasher 11 ------------- 1-ref Gearbox, Center Sextion Blade 10 ------------- 1-ref Gearbox, Divider 2002 Alamo Group Inc. Parts Section -26
NOTES 2002 Alamo Group Inc. Parts Section -27
Blades & Carriers Pan Carrier Standard 1 2 2 Qty Shown For One 20' Model Item Part No. Qty Description 1 007699 Blade Pan Weldment, (Center, LH Wing & RH Wing) 2 00761081 1 Blade Set, 6 Blades, ( CCW & 2 CW) 007297 Blade Updraft, CCW (LH Wing & Center) 0072 2 Blade Updraft, CW (RH Wing) 8227 6 Blade Bolt 9216 6 Washer JRC1610 6 Locknut 2002 Alamo Group Inc. Parts Section -28
Blades & Carriers Bar Carrier Optional 1 2 Qty Shown for Carriers Center, Left & Right Wing ITEM PART NO. QTY DESCRIPTION 1 007879 Blade Bar Weldment 2 8201 6 Flat Blade 0820100 CCW (Center & Left Wing) Fan Blade 0820102 2 CW (Right Wing) Fan Blade 081120060 12 Blade Bushing 7AH8116 6 Hex Head Bolt JRC110 6 Locknut Note: #081120199 Set of 6 Flat Blade cw/ccw (8201) #08112099 Set of 6 Fan Blades cw/ccw (2 cw/0820102 and ccw/0820100) Fan Blades may be used as botm blade only - Blade Bushings Item # must be used per carrier even if dual blades are not used. FAN BLADES MAY BE USED AS THE BOTTOM BLADE ONLY 2002 Alamo Group Inc. Parts Section -29
March 1990 Driveline PTO S/N AG20-010 1 P/N 007009 (0 RPM) P/N 00771 (1000 RPM) Note: Triangle Shaft and Tube Yellow Shields - Cat Drivelines. 2, 21 17 2 1 1 2, 12 1 26 27 2 18 11,16 1 8 Item Part No. Qty Description 1 007908 1 Yoke, 1-/" X 20 Spl. 2 007286 2 Cross & Bearing 0079119 1 Yoke Collar w/ Circlip 0072881 Grease Fitting 007070 1 Yoke & Outer Tube 6 00770 1 D/L Half, Mower End 8 00707 1 Yoke & Inner Tube 9 00707 1 D/L Half Asy (0 PTO) 007708 1 D/L Half Asy (1000 PTO 11 007610 1 Grease Fitting 12 007078 1 Central Body 1 007078 1 Yoke, 1-/8" X 6 Spl. 00770 1 Yoke, 1-/8" X 21 Spl. Item Part No. Qty Description 1 0077 1 Push Pin Set, Twist Collar (0) 007079 2 Push Pin Set, Dbl Pin (0) 0079207 1 Push Pin Set, Twist Collar (1000) 0079208 1 Push Pin set, Dbl Pin (1000) 1 007082 1 Shield Asy Complete 16 007068 1 Cross & Bearing 17 007819 1 Roll Pin 18 0078160 1 Roll Pin 21 0079111 1 Yoke, F/ Outer Tube 22 0079112 1 Yoke, F/ Inner Tube 2 0077818 1 Tube, Inner 2 0077817 1 Tube, Outer 26 00707 1 Shield Bearing, Outer 27 00707 1 Shield Bearing, Inner Note: #007009 Asy (0) NLA replaced by #007602 Asy, #00771 Asy (1000) NLA replaced by #00760 Asy Parts WILL NOT interchange between New & Old D/L's. 2002 Alamo Group Inc. Parts Section -0 22
Apr. 1990 Sep. 1990 Driveline PTO P/N 00792 (0 RPM) P/N007922 (1000 RPM) S/N AG20-010 S/N AG20-0109 Note: Spline Shaft & Tube Black Shields - Cat Drivelines. 1 1 17 2 7 6 8 1 12 11 10 9 1 Note: #00792 (0 RPM) Asy NLA replaced by #007602 Asy #007922 (1000 RPM) Asy NLA replaced by #00760 Asy Parts WILL NOT interchange between New & Old Style Item Part No. Qty Description 1 00792 1 Yoke, QD 1-/8" X 6 Spl. (0) 007922 1 Yoke, QD 1-/8" X 21 Spl. (1000) 2 00792 1 Body Asy 00792 2 C & B Kit 00792 1 Tube & Sleeve 007926 1 Bell Shield 6 007927 1 Shield Tube 7 12 Shield Bearing 8 007928 1 Nylon Bearing 9 W827A 1 Clamp Yoke 10 W80 1 C & B Kit 11 007929 1 Yoke & Shaft 12 007920 1 Inner Shield 1 007921 Shield Bearing 1 71 1 Collar Kit 1 00792 1 Male Half Asy 16 007927 1 Female Half Asy (0) 007926 1 Female Half Asy (1000) 17 02961 2 Grease Fitting 2002 Alamo Group Inc. Parts Section -1
Oct. 1990 Driveline PTO S/N AG20-01060 Note: Star Shape Shaft & Tube Black Shields - Cat Drivelines 2 16 18 6 2 1 7 2 1 1 12 8 1 22 2 20 9 17 11 10 26 2002 Alamo Group Inc. Parts Section -2
Oct. 1990 Driveline PTO S/N AG20-01060 P/N 007602 (0 RPM) - 1-/8-6 Spline PTO P/N 00760 (1000 RPM) - 1-/8-21 Spline PTO P/N 0076 (1000 RPM) - 1-/-20 Spline PTO 0 RPM 1000 RPM 1000 RPM 1-/8"-6 1-/8"-21 1-/"-20 Item Part No. Part No Part No.. Qty Desription 007602 ------------- ------------- -- Driveline Asy Complete (0 RPM) ------------- 00760 ------------- -- Driveline Asy Complete (1000 RPM) ------------- ------------- 0076 -- Driveline Asy Complete (1000 RPM) 00760662 0076066 0076 1 Driveline Half Asy, Tracr End 0076066 00760667 00766 1 Driveline Half Asy, Impl End 1 71 878 00761 1 Yoke, QD (PTO End) 2 882 882 882 1 Double Yoke 882 882 882 1 Grease Fitting 72 72 72 1 Inboard Yoke 7 7 7 2 Cross & Bearing Kit 6 88 88 88 2 Spring Pin 7 0076062 0076062 00767 1 Tube, Inner 8 007606 007606 00768 1 Tube & Sleeve, Outer 9 889 889 889 1 Inboard Yoke 10 0076066 0076066 0076066 1 Yoke, 1-/" QD, Impl End 11 886 886 886 1 Cross & Bearing Kit 12 89 89 89 2 Bearing Ring 1 0076060 0076060 007660 1 Shield, Outer 1 0076061 0076061 007661 1 Shield, Inner 1 720 720 720 1 Cone & Bearing Asy. 16 899 899 899 1 Shield, Tracr End 17 899 899 899 1 Shield, Impl End 18 797 797 797 8 Screw 20 0921000 0921000 0921000 1 Safety Chain 21 007600 007600 007600 1 Outer Decal 22 007600 007600 007600 1 Inner Decal 2 897 897 897 1 Support Bearing 2 891 891 00796 1 Collar Kit, PTO End 26 00796 00796 00796 1 Collar Kit, Impl End 2002 Alamo Group Inc. Parts Section -
March 199 Driveline Intermediate S/N AG20-01109 Note: Triangle Shaped Shaft & Tube, Yellow Shields - Cat Driveline Series 6 Shielding 1, 9 1 10, 1 2 11 8 12 6 7 Item Part No. Qty Descrption Series 6 00766 -- Driveline Asy w/ Series 6 Shields 1 007908 1 Outer Yoke 1-/" - 20 Spline 2 007702 1 Slide Collar Repair Kit 007068 2 Cross Journal Set 007 1 Grease Nipple for Tube 007 2 Grease Nipple 6 0076601 1 Driveline Half Asy w/ Shields (Mower End) 7 007690 1 Driveline Half Asy w/ Shields (Tracr End) 8 0070 6 Nylon Bolt 9 0072 1 Locking Collar Outer 10 0071 1 Locking Collar Inner 11 00707 1 Shield Complete Outer 12 00708 1 Shield Complete Inner 1 00709 1 Shield Complete 1 007617 1 Slip Clutch INNER SHIELD 00766 " Dia. Series 6 9-/8" Circ. OUTER SHIELD 00766-1/" Dia. Series 6 10-1/8" Circ. 2002 Alamo Group Inc. Parts Section -
Apr. 199 Driveline Intermediate S/N AG20-01110 Note: Spline Shaft & Tube - Yellow Shields - Cat Driveline. Series 6 or 8 Shielding Use dimensions shown identify Series 6 or Series 8 driveshafts before ordering parts. 1, 9 1 10, 1 2 11 8 12 6 7 00766 00766A Item Part No. Part No. Qty Description 1 007908 007908 1 Outer Yoke 2 007702 007702 1 Slide Collar Repair Kit 007068 007068 2 Cross Journal Set 007 007 1 Grease Nipple for Tube 007 007 2 Grease Nipple 6 0076601 00769 1 Mower Half Complete & Shielded 7 007690 007660 1 Tracr Half Complete & Shielded 8 0070 0070 6 Nylon Bolt 9 0072 007620 1 Locking Collar Outer 10 0071 007617 1 Locking Collar Inner 11 00707 007661 1 Shield Complete Outer 12 00708 007662 1 Shield Complete Inner 1 00709 00766 1 Shield Complete 1 007617 007617 1 Slip Clutch INNER SHIELD ID 00766 " Dia. Series 6 9-/8" Circ. 00766A -9/16" Dia. Series 8 11-1/" Circ. OUTER SHIELD ID 00766-1/" Dia. Series 6 10-1/8" Circ. 00766A -1/16" Dia. Series 8 12" Circ. 2002 Alamo Group Inc. Parts Section -
March 199 Driveline Wing S/N AG20-01109 1 Triangle Shaft & Tube w/ Yellow Shields - Cat Driveline Series 6 Shielding, 16 19 9 20 18 1 17 10 1, 2 1 11 8 8 12 6 Item Part No. Qty Description 7 00766 -- Driveline Asy w/ Series 6 Shields 1 007700 1 Clamp Yoke 1-/ 20 Spline 2 0077729 2 Bolt 0077196 2 Bolt 007068 2 Cross Journal Set 007 1 Grease Fitting for Tube 007610 2 Grease Fitting 6 007697 1 Driveline Half AsyOuter, w/shields & Clutch 7 007698 1 Driveline Half Asy Inner, w/shield & Clamp Yoke 8 0070 6 Nylon Bolt 9 0072 1 Locking Collar Outer 10 0071 1 Locking Collar Inner 11 00702 1 Shield Complete Outer 12 0070 1 Shield Complete Inner 1 0070 1 Shield Complete 1 007617 1 Slip Clutch 1 0076929 1 Inner Yoke 16 007690 1 Roll Pin, Inner 17 007691 1 Inner Tube 18 007692 1 Outer Tube 19 00769 1 Outer Yoke 20 00769 1 Roll Pin, Outer INNER SHIELD 00766 " Dia. Series 6 9-/8" Circ. OUTER SHIELD 00766-1/" Dia. Series 6 10-1/8" Circ. 2002 Alamo Group Inc. Parts Section -6
Apr. 199 Driveline Wing S/N AG20-01110 1 Note: Triangle Shaft & Tube w/ Yellow Shields - Cat Driveline Series 6 or 8 Shields, 16 19 9 20 18 1 17 10 1, 2 1 11 8 8 12 6 Item Part No. Part No. Qty Description 00766 ------------ -- Driveline Asy w/ Ser 6 Shields ------------- 00766A -- Driveline Asy w/ Ser 8 Shields 1 007700 007700 1 Clamp Yoke 2 0077729 0077729 2 Bolt 0077196 ------------- 2 Bolt 007068 007068 2 Cross Journal Set 007 007 1 Grease Fitting for Tube 007610 007610 2 Grease Fitting 6 007697 00767 1 Driveline Half Asy Outer, w/shield & Clutch 7 007698 00766 1 Inner D/L Half Asy Inner w/shield & Clamp Yoke 8 0070 0070 6 Nylon Bolt 9 0072 007620 1 Locking Collar Outer 10 0071 007617 1 Locking Collar Inner 11 00702 00768 1 Shield Complete Outer 12 0070 00769 1 Shield Complete Inner 1 0070 00768 1 Shield Complete 1 007617 007617 1 Slip Clutch 1 0076929 007672 1 Inner Yoke 16 007690 007690 1 Roll Pin, Inner 17 007691 00766 1 Inner Tube 18 007692 007666 1 Outer Tube 19 00769 007671 1 Outer Yoke 20 00769 00769 1 Roll Pin, Outer INNER SHIELD ID 00766 " Dia. Series 6 9-/8" Circ. 00766A -9/16" Dia. 00766A -1/16" Dia. Series 8 11-1/" Circ. Series 8 12" Circ. 2002 Alamo Group Inc. Parts Section -7 7 OUTER SHIELD ID 00766-1/" Dia. Series 6 10-1/8" Circ.
Sep. 199 Clutch S/N AG20-01001 S/N AG20-01118 USED ON: Intermediate & Wing Drivelines 7 10 1 2 1-/" X 20 Spline Hub Clamp Hub 8 9 6 11 To Adjust Tighten Springs till they are 1-/16" long Item Part No. Qty Description 007617 -- Clutch Asy, Complete 1 007199 8 Bolt and Nut Set 2 00720 1 Pressure Plate, Machined Plate 007201 1 Clutch Plate 007202 Disk 00799 1 Body Friction Clutch 6 007600 2 Bolt and Nut Set 7 0071 1 Plate w/holes 8 00701 1 Spacer 9 00708 1 Yoke Friction 10 0070 8 Spring 11 0070 1 Dirt Shield NOTE: The Style of Clutch changed even though the Asembly Part No. did not, Check which type Pressure Plate (Item 2) you have, If Clutch use Machined Metal One or Formed Metal One which is the Later Style. 2002 Alamo Group Inc. Parts Section -8 8 Bolts (Item # 1)
Oct. 199 Clutch S/N AG20-01119 USED ON: Intermediate & Wing Drivelines 9 10 This Clutch used on D/L w/ Triangle Shaped Tubes 2 8 6 1 1-/ X 20 Spline Hub Clamp Hub 7 To Adjust Tighten Spring till they are 1-/16" Long 8 Bolts (Item # 9) Later Item Part No. Qty Description Clutches have 6 Bolts & Springs 007617 -- Clutch Asy. Complete 1 00708 1 Flange Yoke 2 00799 1 Clutch Support 00766810 1 Pressure Plate, Formed Plate 0071 2 Plate with Holes 007202 Lining Ring 6 00701 1 Bushing 7 0070 8 Spring 8 007600 2 Nut & Bolt 9 007199 8 Nut & Bolt 10 007201 1 Intermediate Plate 2002 Alamo Group Inc. Parts Section -9 NOTE: The Style of Clutch changed even though the Asembly Part No. did not, Check which type Pressure Plate (Item ) you have, If Clutch use Machined Metal one or Formed Metal which is the Later Style.
Deflecrs Front Center Section 1 6 2 7 8 9 FRONT CENTER SECTION Item Part No. Qty Qty Qty Description Ctr RH LH 007890 1 -- -- *Deflecr Asy, Center Front Center 007891 -- 1 -- *Deflecr Asy, Center Front RH Side 007892 -- -- 1 *Deflecr Asy, Center Front LH Side 1 0078287 1 -- -- *Bracket, Metal ( Mounting Holes) 0078288 -- 1 -- *Bracket, Metal ( Mounting Holes) 0078289 -- -- 1 *Bracket, Metal ( Mounting Holes) 2 007829 1 1 1 Panel, Rubber 0200700 Bolt 00002700 Flatwasher 00001800 Locknut 6 0001100 6 6 6 Bolt 7 0001800 6 6 6 Locknut 8 00011100 12 12 12 Flatwasher 9 020800 6 6 6 Woodwasher #00786 Complete Front Deflecr Set, Center Section & Wings * Front center Shown, LH & RH center section look same as center bracket except for the number of mounting holes, LH & RH is from standing behind mower facing forward. 2002 Alamo Group Inc. Parts Section -0
Deflecrs Front LH & RH Wing 1 6 2 9 8 7 Item Part No. Qty Qty Description RH LH 00789 -- 1 Deflecr Asy, LH Wing 0078789 1 -- Deflecr Asy, RH Wing 1 0099918 6 6 Bolt 2 0078291 1 1 Bracket, Rubber 0078297 1 1 Panel, Rubber 00002700 6 6 Flatwasher 00001800 6 6 Locknut 6 0001100 1 1 Bolt 7 0001800 1 1 Locknut 8 00011100 26 26 Flatwasher 9 020800 1 1 Woodwasher #00786 Complete Front Deflecr Set, Center Section & Wings 2002 Alamo Group Inc. Parts Section -1
Deflecrs Rear Center Section 1 2 REAR CENTER SECTION Item Part No. Qty Description 00789 1 Deflecr Asy, Center Section Rear 1 007829 1 Band, Metal 2 0078290 1 Panel, Rubber 0200700 Bolt 00002700 Flatwasher 00001800 Locknut #00787 Complete Set of Rear Deflecrs Center - Left & Right Wings 2002 Alamo Group Inc. Parts Section -2
Deflecrs Rear LH & RH Wing 1 Left Wing Deflecr Asy Shown, RH Wing mounts opposite Shown with Item # 2A outside. 2 11 6 2A 9 7 7 9 10 8 LH or RH REAR WING Item Part No. Qty Qty Description RH LH 00789 1 1 Wing Deflecr Asy, LH or RH Wing 1 0078292 1 1 Mounting Brace 2 620 Spacer, Short 2A 0078771 1 1 Spacer, Long (outer end spacer) 0078296 1 1 Rubber Panel 7A812 Bolt 00002700 Flatwasher 6 0001100 12 12 Bolt 7 00011100 2 2 Flatwasher 8 0001800 12 12 Locknut 9 00001800 Locknut 10 020800 12 12 Woodwasher 11 0099918 1 1 Bolt 2002 Alamo Group Inc. Parts Section -
Chain Guards Front Center Section 1,2 9,, 6 8 7 FRONT CENTER CHAIN GUARD Item Part No. Qty. Description 1* 081101100 1 Chain Guard Asy, RH Center (Shown)* 081101200 1 Chain Guard Asy, LH Center (Not Shown)* 2 081101110 1 Chain Guard Bracket, RH Center (Shown) 081101210 1 Chain Guard Bracket, LH Center (Not Shown) 06210010 1 Chain Rod, " LG (Not Shown) 062100102 1 Chain Rod, 28" LG (Not Shown) 081101101 1 Chain Rod, 1" LG (Not Shown) 6 078100 1 Chain, 7 Links @ /16 7 007882 Bolt 8 1B800 Flatasher 9 00001800 Locknut Note *: Qty shown for LH or RH Center Section - Double quantity for both LH & RH Center *These assemblies include items # through #11 #081100000 Front Chain Guard Set includes 1 ea of # 081101100 & 081101200, ea of # 08110100, A Complete Set of Chain guards for Front. Includes Center, LH & RH Wings. 2002 Alamo Group Inc. Parts Section -
Chain Guards Front LH & RH Wing 1,2 7 6 FRONT WING CHAIN GUARD Item Part No. Qty. Description 1* 08110100 1 Chain Guard Asy, LH or RH Wing 2 08110101 1 Chain Guard Bracket, LH or RH Wing 078100 1 Chain Rod (Not Shown) 088120010 1 Chain, 8 Links @ /16 7A812 Bolt 6 1B800 Flatwasher 7 00001800 Locknut Note *: Items #1 includes items # 2 thru #7, 2 Assemblies (Item # 1) Required Per Wing. Assemblies Required Per Mower on 20 ' Models #081100000 Front Chain Guard Set includes 1 ea of # 081101100 & 081101200, ea of # 08110100, A Complete Set of Chain guards for Front. Includes Center, LH & RH Wings. 2002 Alamo Group Inc. Parts Section -
Chain Guards Rear Center Section 8 1,2, 7 6 REAR CENTER CHAIN GUARD Item Part No. Qty. Description 1* 08111100 1 Chain Guard Asy, Rear Center 2 08111101 1 Chain Guard Bracket, Rear Center 06210010 2 Chain Rod, " (Not Shown) 062100202 1 Chain Rod, 72" (Not Shown) 06210020 70 Chain, 6 Links 6 007882 Bolt 7 1B800 Washer 8 00001800 Locknut Note *: Qty shown for Center Section, Drawing is shown cut fit Page, Rear Center Chain Guard is one piece and goes all the way across Rear Center Section #08110900 Rear Chain Guard Set includes 1 ea. of #08111100, 08111200 & 0811100, A Complete Set of Chain Guards for Rear, Includes Center, LH & RH Wings. 2002 Alamo Group Inc. Parts Section -6
Chain Guards Rear LH & RH Wing 10 1,2 7 9 8 6 8 8 REAR LH & RH CHAIN GUARD Item Part No. Qty. Description 1* 08111200 1 Chain Guard Asy, RH Wing Rear (Shown) 0811100 1 Chain Guard Asy, LH Wing Rear (Not Shown) 2 08111210 1 Chain Guard Bracket, RH Wing Rear (Shown) 0811110 1 Chain Guard Bracket, LH Wing Rear (Not Shown) 08111201 1 Chain Rod (Not Shown) 620 Pipe Spacer 620 1 Pipe Spacer 6 007090 7 Chain Links 7 000100 1 Capscrew 8 7A812 Capscrew 9 1B800 Washer 10 GR810 Locknut *Assemblies include Items #2 thru 10 #08110900 Rear Chain Guard Set includes 1 ea. of #08111100, 08111200 & 0811100, A Complete Set of Chain Guards for Rear, Includes Center, LH & RH Wings. 2002 Alamo Group Inc. Parts Section -7
Sep. 1991 Hyd. Valve Closed Center ( Optional ) S/N AG20-0108 Note: Optional Equipment 1 2 Item Part No. Qty. Description 1 B6112 1 Hydraulic Valve Asy ( spool) 2 6101 1 Bracket, Mounting 00016200 6 Bolt 100 6 Washer B180 6 Nut B6112 no longer available as assembly - replace with #00798 2002 Alamo Group Inc. Parts Section -8
Oct. 1991 Hyd. Valve Closed Center ( Optional ) S/N AG20-0108 Note: Optional Equipment 2 1 7 Item Part No. Qty Description 1 00798 1 Closed Center Valve 2 007119 Detent Repair Kit 007112 Handle Assembly 0071002 1 Closed Center Plug 00718 - Repair Kit-Spring Return Center 6 00716 1 Spool Seal Kit for Item #1 or #2 (Not Shown) 7 007207 1 Non-Relief Valve Plug (Closed Center) NOTE: The Three Spool Control valve must have detent float positions for the wing cylinders. This will allow decks float conur of ground and prevent stress in deck components. 2002 Alamo Group Inc. Parts Section -9
Sep. 1991 Hyd. Valve Open Center ( Optional ) S/N AG20-0108 Note: Optional Equipment 1 2 Item Part No. Qty. Description 1 B6102 1 Hydraulic Valve Asy ( spool) 2 6101 1 Bracket, Mounting 00016200 6 Bolt 100 6 Washer B180 6 Nut B6102 no longer available as assembly - replace with #0080200 2002 Alamo Group Inc. Parts Section -0
Oct. 1991 6 Hyd. Valve Open Center ( Optional ) S/N AG20-0108 Note: Optional Equipment 2 1 10 Item Part No. Qty Description 1 0080200 1 Open Center Valve 2 007119 2 Detent Repair Kit 007110 1 High Pressure Relief Valve Kit 007112 Handle Assembly 007112 1 Open Center Plug 6 00718 - Repair Kit-Spring Return Center 7 00716 1 Spool Seal Kit for Item #1 or #2 (Not Shown) NOTE: The Three Spool Control valve must have detent float positions for the wing cylinders. This will allow decks float conur of ground and prevent stress in deck components. 2002 Alamo Group Inc. Parts Section -1
Sep. 1990 Hyd. Cyl. Center Axle Lift (Standard Lift) S/N AG20-0109 Note: Screw on stroke control item #9 16,19 1,7 6 8 10,11 17 1 1 1 12 9 18 Item Part No. Qty. Description 1 611B1 1 Hydraulic Cyl. 06110001 1 Base Clevis 0611000 1 Pisn 6 06110006 1 Rod 7 06110007 1 Barrel 8 6112 1 Breather Plug 9 06110012 1 Stroke Control 10 B620 1 Nut, Rod Clevis 11 7E621 1 Socket Hd. Bolt 12 B8200 8 Nut, Tie Rod 1 06110016 1 Head 1 06110017 Tie Rod 1 6911 1 Lock Nut, 1-1NF 16 6111 2 Pin, Clevis 17 7107B1 2 Clip 18 06110022 1 Rod, Clevis 19 0611001 Seal Kit 081121000 1 Hose (Not Shown) Note: Cylinder #611B1 no longer available as assembly - Replace complete cylinder with #007996 Cyl & 0072 Control Spacer Kit. Parts will not interchange between new & Old style Cyl.. 2002 Alamo Group Inc. Parts Section -2
Oct. 1990 Hyd. Cyl. Center Axle Lift (Standard Lift) S/N AG20-01060 Note: Clip on stroke control item 19. 19 1,2 7 8 9 1,2 11 Old Style Pisn Seal. 1 1 12 6,10 1 NOTE:Seal install over Chamfer side of Pisn. Note position of Chamfer on New Style Pisn. Item Part No. Qty Description 007996 1 Hyd Cyl 1 8 2 Pivot Pin 2 16016 2 Clip Pin 00760199 1 Seal Kit 67 1 Pisn Nut 79 1 Breather Plug (Not Shown) 6 27 1 Bolt 7 00760661 1 Pisn 8 0076019 1 Tube Item Part No. Qty Description 9 00760200 1 Pisn Rod 10 76 1 Hex Nut 11 690 8 Tie Rod Nut 12 00760197 1 Head 1 87 1 Outer Clevis 1 00760196 1 Cap 1 00760202 Tie Rod 19 0072 1 Control Spacer Kit NOTE: Seal Kit (#00760199) contains both old and new style pisn seals. New style seal can be installed on old style pisn. 2002 Alamo Group Inc. Parts Section -
Hyd. Cyl. Center Axle Lift (Hyd. Level Lift Option) 11,12 2 10 10 11,12 1 7 9 8 6 Item Part No. Part No. Part No. Qty. Description 8719 ------- ------- 1 Cy. Asy, Center Axle, ( -1/2" x 8") ------ 8720 ------ 1 Cyl. Asy, RH Wing Axle, (-1/" x8") ------ ------ 8721 1 Cyl. Asy, LH Wing Axle, ( " x 8") 1 8772 8778 878 1 Base Clevis 2 70M 70M ------- 1 Pisn Nut, (8719-8720 Only) ------- ------- 67M 1 Pisn Nut (8721 only 8768 877 8780 1 Pisn 8769 8776 8781 1 Tube 706 706 87 1 Pisn Rods 6 87 87 87 1 Rod Clevis 7 877 877 878 Tie Rod 8 689 689 ------- 8 Nut, 9/16" (8719-8720 Only) ------- ------- 76 8 Nut, 1/2" (8721 Only) 9 877 8779 8786 1 Head 10 876 876 8766 1 Seal Kit (Not Shown) 11 8 8 8 2 Pin, Clevis 12 16016 16016 16016 Cotter Pin Note: Hose route will depend on cylinder from left right mounting order by size. Measure old hose before ordering replacements. Cylinders must be connected larger (8719) Medium (8720) smaller (8721) in Oil Flow order or this system will not work. All Air Must be bled from system and mounted so Air can't enter system. 2002 Alamo Group Inc. Parts Section -
Sep. 1990 Hyd. Cyl. Wing Lift & Fold S/N AG20-0109 Note: # B610B1 & # 007991 no longer available as an asy. Replace w/ # 007997 as asy. 16 18 19 6 7 1,8 1 9,10 17 19 1 1 12 11 Item Part No. Qty. Qty Description 1* B610B1 1 -- Hyd. Cyl. Asy, (1-1/" Rod) 007991 -- 1 Hyd Cyl. Asy. (1-1/2" Rod) 06110001 1 1 Base Clevis 6 0611000 1 1 Pisn 7* 06100001 1 -- Rod (1-1/") 007992 -- 1 Rod Kit (1-1/2") (whead, Rod, & Seal Kit) 8 06100002 1 1 Barrel 9 B620 1 1 Nut, Rod Clevis 10 7E621 1 1 Socket Hd., Bolt 11 06110022 1 1 Rod Clevis 12 B8200 8 8 Nut, Tie Rod 1* 06110016 1 -- Head (1-1/") 00799 -- 1 Head Kit (1-1/2") (w/head, Rod, & Seal Kit) 1 0610000 Tie Rod 1 6911 1 1 Lock Nut 16 6111 2 2 Clevis Pin 17 7107B1 2 2 Clip 18* 6112 1 1 Plug 19 0611001 1 -- Seal Kit (1-1/" Rod) 00799 -- 1 Seal Kit (1-1/2" Rod) 20 0811261100 1 1 Hose (Not Shown) Note * : 1-1/" Rod was standard and most common, The 1-1/2" Rod cylinders were shipped and not known till after they were shipped, there were not many of the 1-1/2" Rod Cylinder used or shipped 2002 Alamo Group Inc. Parts Section -
Oct. 1990 Hyd. Cyl. Wing Lift & Fold S/N AG20-01060 1,2 7 8 9 20 1 Old Style Pisn Seal. 1 1 12 11 6,10 1,2 NOTE:Seal install over Chamfer side of Pisn. Note position of Chamfer on New Pisn. Item Part No. Qty Description 007997 1 Hyd Cyl Asy 1 6111 2 Pivot Pin 2 162012 2 Clip Pin 00760199 1 Seal Kit 67 1 Pisn Nut 6112 1 Breather Plug (Not Shown) 6 27 1 Bolt 7 00760198 1 Pisn 8 0076019 1 Tube 9 00760201 1 Pisn Rod 10 78 1 Hex Nut 11 690 8 Tie Rod Nut 12 00760197 1 Head 1 87 1 Outer Clevis 1 00760197 1 Cap 1 0076020 Tie Rod 19 0811261100 1 Hose (Not Shown) NOTE: Seal Kit (#00760199) contains both old and new style pisn seals. New style seal can be installed in old style pisn. 2002 Alamo Group Inc. Parts Section -6
NOTES 2002 Alamo Group Inc. Parts Section -7
Hyd. Schematic Lift & Fold (Standard) Inlet from Tracr System Outlet Tracr System Reservoir 8 11 7 1 11 10 9 12 11 11 10 10 9 9 Valve Mounting Kit # includes items, 7, 8, 9, 10, 11, 1, & 1. LH Wing 11 6 6 6 11 RH Wing 9 10 1 9 9 10 11 11 10 11 Center Axle 1 2 1 Inlet Hose Route Under Valve Mounting Bracket 1 16,17 18 19,20,21 7 7 1 19 Drill Holes in Fender 12 11 2002 Alamo Group Inc. Parts Section -8
Hyd. Schematic Lift & Fold (Standard) Item Part No. Qty Description 1 -------------- 2-ref Cylinder, Wing Lift & Fold 2 -------------- 1-ref Cylinder, Axle Lift -------------- -ref Hose -------------- -ref Restricr Fitting 000999 2 Elbow Deg. 6 -------------- -ref Breather 7 72 2 Reducer 8 17 2 Hydraulic Hose 9 2107 Quick Disconnect Coupler 10 0296060 Straight Adapter 11 91 Elbow 90 Deg. 12 -------------- 1-ref Open Valve Bank -------------- 1-ref Closed Valve Bank 1 0079682 1 Shield 1 -------------- 1-ref Stroke Control 1 8166 1 Fender Bracket 16 1020000 2 Bolt 17 76 2 Spacer 18 00010600 1 Bolt 19 0001100 Bolt 20 010166 7 Lockwasher 21 0001901 7 Nut NOTE: This is the Standard Hydraulic Lift and Fold Schematic, This sytem will use 1 Cylinder each wing lift & Fold. There will be 1 Cylinder for the Center Axle for Lift, The Wing Axles will have Lift Screws that are adjusted manually. 2002 Alamo Group Inc. Parts Section -9
Hyd. Schematic Lift & Fold (Hyd. Level Lift Option) 11 12 6 10 9 1 2 7 2 1 8 2002 Alamo Group Inc. Parts Section -60
Hyd. Schematic Lift & Fold (Hyd. Level Lift Option) Item Part No. Qty Description 1 729 2 Adapr - Restricr 2 917 2 Hydraulic Adapr 90 0 0811261100 2 Hydraulic Hose (288" Long) 06111200 1 Hydraulic Hose (120" Long) 081121000 2 Hydraulic Hose (20" Long) 6 00760626 1 Hydraulic Hose (60" Long) 7 8719 1 Hydraulic Cylinder -1/2" Dia. 8 8720 1 Hydraulic Cylinder -1/" Dia. 9 8721 1 Hydraulic Cylinder " Dia. 10 91 Hydraulic Adapr 90 0 (1 w/06111200) 11 081210100 2 Rear Lift Bracket Asy. 12 081210200 2 Adapter Plate Asy. NOTE: The above Hose's & Brackets are ONLY USED if Mower is equipped with the OPTIONAL Hydraulic Level Lift System. If Mower does not have the Level Lift System there will only be one Cylinder for Center Axle and Wings will have Standard Lift Screw. The Hyd. Level Lift Cylinders are Phasing Cylinders and WILL NOT WORK as the standard lift Cylinder. If Cylinders are disassembled care MUST be taken make sure Barrels of Cylinders are re-installed in the correct direction. 2002 Alamo Group Inc. Parts Section -61
Jan. 1990 Wheel Hubs S/N AG20-010 7 This area IS machined. Marking on hub have word Alamo Cast in it. Axle spindle WILL NOT HAVE washer welded on behind seal. 8,10,12 6 1 9 11,1, Note; Install Item # 7 as shown with all Wheels EXCEPT the laminated Tire & Wheel. The Nut is installed turned around backwards from what is shown when using Laminated Tire & Wheel. This is very Important! 1 16 Item Part No. Qty Description 007721 -- Hub Asy Complete (items thru 1) 007676 1 Bearing Cup(Outside) 0070 1 Bearing Cone(Inside) 007677 1 Bearing Cup(Inside) 6 007688 Bolt, Wheel Stud 7 007061 Nut, Lug Nut 8 007690 1 Nut, Slotted Thin 9 002970 1 Seal 10 00769 1 Washer 11 007692 1 Dust Cap 12 0000000 1 Cotter Pin 1 000000 1 Grease Fitting 1 007689 1 Wheel Hub w/cups & Studs 1 07122102 1 Bearing Cone(Outside) 16 0076001 ref Spindle, Single Wheel (Weld In Spindle) 0076002 ref Spindle, Dual Wheel (Weld in Spindle) 007628 ref Wheel Hub Accessory Kit (Includes Items,,,7,8,9,10,11,12,1) Note: # 007721 Includes 1 each of #007689 and 1 each of #0076828 2002 Alamo Group Inc. Parts Section -62
Feb. 1990 Wheel Hubs S/N AG20-0106 This area is NOT machined. No marking on hub. Axle spindle WILL HAVE washer welded on behind seal. 11 12 9 2 1 1 6 7 8 10 Item Part No. Qty. Description 712 1 Hub Asy Complete (w/ items 1 thru 1) 1 7127SA 1 Hub Sub Asy (w/ items,,11,12 & 1) 2 7127F 1 Grease Seal 7127E 1 Inner Bearing Cone 7127D 1 Inner Bearing Cup 00016900 1 Outer Bearing Cup 6 029719 1 Outer Bearing Cone 7 1B100 1 Spindle Washer 8 7127J 1 Spindle Nut 9 1621/2012 1 Cotter Pin 10 7127G 1 Hub Cap 11 1198 Hub Bolt 12 007061 Hub Nut 1 000000 1 Grease Fitting NOTE: Hub Only is not Offered as a Seperate Repair Part. When Ordering Bearings, it is Recomended That Both Cup and Cone be Specified. To ID this hub note Spindle bolt size, it is a 7/8" Nut, earlier Hub used a 1" Bolt. This Hub also used a Washer welded Spindle as a Seal protecr, The earlier Spindle DID NOT. 2002 Alamo Group Inc. Parts Section -6
Tire & Wheel 1 2 Item Part No. Qty Description Wheel Group (Quantities for 1-Cutter, 2 Wheels Complete) 1 0079698 -- Implement Tire & Wheel Asy 6:70 X 1 (Includes *) 00008700 -- *1" Wheel Only 00601700 -- * Implement Tire Only, 6:70 X 1 Tube Type 007199 -- * Tube F/ Implement Tire Only, 6:70 X 1 0077161 -- Used 1" Airplane Tire & Wheel (Not Shown) 0079700 -- Used 1" Airplane Tire & Wheel (Not Shown) 0079698 -- Implement Tire & Wheel (Not Shown) 2 0002200 -- 6 X 9 Laminated Tire & Wheel Asy 00766911A -- Used Aipplane Tire & Whl, 22 X 6.6, Foam Filled 2002 Alamo Group Inc. Parts Section -6
NOTES 2002 Alamo Group Inc. Parts Section -6
Nov. 1992 Winch & Stand Optional S/N AG20-0110 1 6,8,10 7 9,8,10 2,8,10,8,10,8,10 Item Part No. Qty Description 1 0811270100 1 Winch Stand Weldment 2 081127000 1 Support Leg, LH 0811270200 1 Support Leg, LH 0001100 Bolt 007882 6 Bolt 6 00011100 1 Flatwasher 7 010166 Lockwasher 8 0000100 6 Lockwasher 9 0001900 Locknut 10 0001200 6 Locknut NOTE: This winch Stand will be replaced by Stand on following page. 2002 Alamo Group Inc. Parts Section -66
Dec. 1992 Winch & Stand Optional S/N AG20-0110 2,6,7 1 9,10 Item Part No. Qty Description 081127000 -- Winch & Stand Asy w/cable & Hardware 1 007617 1 Winch Stand Weldment 2 007096 1 Winch 0811280000 1 Cable 0076 1 Pulley & Block 00766 1 Chain 6 0001100 2 Bolt 7 00011100 2 Flatwasher 8 0001800 2 Locknut 9 007882 2 Bolt 10 00001800 2 Locknut 2002 Alamo Group Inc. Parts Section -67
Decals 11 1 9 20 1 1A 20 22, 8 10 21 1 16 6 17, 1 21 19 19 12 12 7 1 2 2 7 2002 Alamo Group Inc. Parts Section -68
Decals Item Part No. Qty Description 1 0079117 1 Danger, Multiple Hazard, Operation, Transport, Parking 2 00780 2 (1) Danger, Folding Wing Multiple Hazard 007600 () Danger, Driveline Shield Missing; Do Not Operate 007600 () Danger, Rotating Driveline, Entanglement 0076007 1 Warning, Use/Repair Shields & Guards 6 007609 1 Warning, Oil Leak Detection, Skin Penetration 7 00768 2 (1) Danger, Cutting Blades, Thrown Objects 8 00769 1 Danger, Driveline Hazards, 0 RPM 9 0292100 1 Caution, Alamo Repair Parts 10 007661 1 INSTRUC-Slip Clutch 11 02007 * SMV Emblem 12 9920 2 Red Reflective Tape 1 9920 2 Yellow Reflective Tape 1A 0076977 1 Notice Owner 1 D102 1 PTO--Drawbar Hole Adjustment 1 D11** 1 1000 RPM PTO D10** 1 0 RPM PTO 16 D17 1 CCW Blade Rotation 17 D18 1 CW Blade Rotation 19 007719 2 Alamo Type, -/8 x 16-/ 20 02960766 2 Logo, Alamo -7/8 x 6-1/2 21 00769670 2 AG20-IV Name Decal Only 22 007807 1 AG20-IV, Serial Plate * Furnished by Tracr Manufacturer ** 0 or 1000 RPM units only. Select correct one. () = For Two Section Units 2002 Alamo Group Inc. Parts Section -69
Decals 1 - - 0079117 SEE INSIDE FRONT COVER 12 - - 9920 RED REFLECTOR 1 - - 9920 YELLOW REFLECTOR 21 -- D06 FL20 NAME ONLY 16 - - D17 - - 007600 0076067 CAUTION FOR YOUR SAFETY AND TO GUARANTEE OPTIMUM PRODUCT RELIABILITY, ALWAYS USE GENUINE ALAMO REPLACEMENT PARTS. THE USE OF INFE- RIOR REPLACEMENT PARTS MAY CAUSE PREMA- TURE OR CATASTROPHIC FAILURE WHICH COULD RESULT IN SERIOUS INJURY OR DEATH. IF YOU HAVE ANY QUESTIONS CONCERNING THE REPAIR PARTS YOU ARE USING, CONTACT ALAMO INDUS- TRIAL, P.O. BOX 9, SEGUIN, TX. 7816. 9 - - 0292100 17 - - D18 1- - D11 OPERATE THIS MACHINE WITH 0 RPM TRACTOR P.T.O. SPEED 1- - D10 10--007661 22 - - 007719 21- - 002960766 2002 Alamo Group Inc. Parts Section -70
Decals A20-IV 2-- 02960766 A1-IV 2-- 0076981 1 - - D102 8 - - 00769 - - 007600 6 - - 007609 2002 Alamo Group Inc. Parts Section -71 1A - - 0076977
Decals 2 - - 00780 7 - - 00768 10 - - 9990 - - 0076007 2002 Alamo Group Inc. Parts Section -72
AG20-IV & AG1-IV Flex Wing Mower Archive Book 1 of 2 2002 Edition AG20-IV & AG1-IV ARCHIVE Printed U.S.A. P/N 02979200