ROUND BALERS Published 10/01 P/N 4895WP PART'S MANUAL An Operator's Manual was shipped with the equipment in the Manual Canister. This Operator's Manual is an integral part of the safe operation of this machine and must be maintained with the unit at all times. READ, UNDERSTAND, and FOLLOW the Safety and Operation Instructions contained in this manual before operating the equipment. If the Operator's Manual is not with the equipment, contact your dealer or M&W (217-784-4261) to obtain a Free copy before operating the equipment. MODEL 5600 & 5690 5600, SERIAL NUMBERS 14929 - CURRENT 5690, SERIAL NUMBERS 12000 - CURRENT Art s-way Manufacturing Co., Inc. Hwy 9 West - PO Box 288 Armstrong, IA. 50514 U.S.A 1020 South Ave. (712)Sangamon 864-3131 M&W Gibson City, Illinois 60936 217-784-4261 2004 Alamo Group Inc.
TO THE OWNER/OPERATOR/DEALER All implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-minded operator who recognizes the potential hazards and follows reasonable safety practices. The manufacturer has designed this implement to be used with all its safety equipment properly attached to minimize the chance of accidents. BEFORE YOU START!! Read the safety messages on the implement and shown in your manual. Observe the rules of safety and common sense! WARRANTY INFORMATION: Read and understand the complete Warranty Statement found in this Manual. Fill out the Warranty Registration Form in full and return it within 30 Days. Make certain the Serial Number of the Machine is recorded on the Warranty Card and on the Warranty Form that you retain. The use of "will-fit" parts will void your warranty and can cause catastrophic failure with possible injury or death.
Parts Section 1 PARTS SECTION
PARTS ORDERING GUIDE The following instructions are offered to help eliminate needless delay and error in processing purchase orders for the equipment in this section. 1. The Parts Section is prepared in logical sequence and grouping of parts that belong to the basic machine featured in this manual. Part Numbers and Descriptions are given to help locate the parts and quantities required. 2. The Purchase Order must include the name and address of the person or organization ordering the parts, who should be charged, and if possible, the serial number of the machine for which the parts are ordered. 3. The Purchase Order must clearly list the quantity of each part, the complete and correct part number, and the basic name of the part. 4. The Manufacturer reserves the right to substitute parts where applicable. 5. Some parts are unlisted items which are special production items not normally stocked and are subject to special handling. Request a quotation for such parts before sending a Purchase Order. 6. The Manufacturer reserves the right to change prices without prior notice. NOTE: Please refer to The Safety Section in the front of this Manual for the proper Part Number when ordering Replacement Safety Decals. For maximum safety and to guarantee optimum product reliability, always use genuine Alamo Group Parts. The use of inferior replacement parts may cause premature or catastrophic failure which could result in serious injury or death. Direct any questions regarding parts to: M&W 1020 South Sangamon Ave. Art s-way Manufacturing Co., Inc. Gibson City, Illinois 60936 Hwy 9 West - PO Box 288 Armstrong, IA. 50514 U.S.A 217-784-4561 (712) 864-3131 2004 Alamo Group Inc. Parts Section 2
PART NAME INDEX BALE COUNT SENSOR - MODEL 5690... 50 BALE RAMP EXTENSION... 59 CLUTCH 540 RPM (P/N 0921000460)... 45 DECAL LOCATION GUIDE... 4 DRIVELINE 1000 RPM... 46 DRIVELINE 540 RPM (P/N 1456404)... 44 DUAL TWINE DRIVE ASSEMBLY... 30 DUAL TWINE TIE SYSTEM... 26 ELECTRICAL SCHEMATIC - MODEL 5600... 55 ELECTRICAL SCHEMATIC - MODEL 5690... 54 ELECTRICAL SYSTEM - MODEL 5600... 52 ELEVATOR... 16 FRONT CHAMBER... 6 GEARBOX... 40, 42 HYDRAULIC SYSTEM... 20, 24 OPTIONAL - WINDROW GATHERING WHEEL... 62 OPTIONAL 1000 RPM CONVERSION KIT (1450424)... 66 PICK-UP... 38 RAMP CABLE LIFT (RIGHT & LEFT)... 58 RAMP CHANNEL... 60 REAR CHAMBER... 10 STANDARD SAFETY LIGHTS... 56 UNDERSIDE... 12 WIRE HARNESS ROUTING... 64 WIRING DIAGRAM - MODEL 5690... 48 WRAP INSERT... 32 WRAP ROLL MOUNTING SYSTEM - MODEL 5690... 36 2004 Alamo Group Inc. Parts Section 3
DECAL LOCATION GUIDE 2004 Alamo Group Inc. Parts Section 4
DECAL LOCATION GUIDE ITEM PART NO. QTY. DESCRIPTION 1 1458316 2 SAFETY OPERATION DECAL 2 1458317 4 DANGER - TAILGATE DECAL 3 2738320 1 IID SHIELD DECAL (INNER DECAL) 4 2738315 1 IID SHIELD DECAL (OUTER DECAL) 5 1438339 2 DANGER - SHARP KNIFE 6 1458367 1 DOOR SAFETY LOCK VALVE DECAL 7 1458362 1 DECAL, WARNING BALER UPSET 8 1458382 4 WARNING HAND PINCH DECAL 9 02962764 4 PINCH POINT DECAL 10 00756059 3 OIL LEAK DECAL 11 1438330 1 CAUTION OPERATING DECAL 12 D103 1 PTO SPEED DECAL, 540 RPM 13 2738332 4 RED OBLONG REFLECTOR DECAL 14 5W118 1 SLOW MOVING VEHICLE DECAL 15 1438326 1 DOG CLUTCH DECAL 16 1458351 1 ELEVATOR CHAIN ADJUSTMENT DECAL 17 1458369 1 DOUBLE TWINE INSTALLATION INSTRUCTION DECAL 18 1458368 1 NET ROUTING DECAL 19 1458310 1 PICK-UP CRANK DIRECTION DECAL 20 1458311 1 PICK-UP HEIGHT POSITION DECAL 21 1428302 2 FILL LINE DECAL 22 1438333 3 GREASE DECAL, 10HRS 23 1428303 1 PICK-UP PIN DECAL 24 1438319 4 OIL DECAL 25 1458366 1 TWINE WRAP DECAL 26 1458364 2 DECAL, OIL CHAIN, 4 HOURS 27 1458371 1 3-YR. WARRANTY 28 00771039 1 GENUINE PARTS DECAL 29 999001 1 TRACTOR CAUTION DECAL 30 00763977 1 NOTICE TO OWNER 31 1458349 1 MODEL NO. 5600 DECAL, RH 1458344 1 MODEL NO. 5690 DECAL, RH 32 1458350 1 MODEL NO. 5600 DECAL, LH 1458345 1 MODEL NO. 5690 DECAL, LH 33 1428310 2 LARGE M & W DECAL 34 1458332 1 M&W LOGO DECAL, RH 35 1458333 1 M&W LOGO DECAL, LH 36 1458346 1 FRONT STRIPE DECAL 37 1458347 2 REAR STRIPE DECAL 38 1458380 1 MADE IN USA 39 00773723 1 DRIVELINE SPANISH TRANSLATION 40 00776031 1 CANISTER MANUAL 41 32901C 2 LOCKNUT 42 00024100 4 FLATWASHER 43 00021400 2 BOLTS 44 4903WC 1 MANUAL FOR CANISTER 45 00776481 1 INSTRUCT DECAL - MANUAL OPERATOR S INSIDE 2004 Alamo Group Inc. Parts Section 5
FRONT CHAMBER 2004 Alamo Group Inc. Parts Section 6
FRONT CHAMBER ITEM PART NO. QTY. DESCRIPTION 1 1452389 1 TWINE BOX FLOOR 2 1452051 1 DIVIDER PANEL LOWER 3 1450396 1 CHAIN DOOR, RH 4 1452358 1 LOWER EXTENSION CHAIN DOOR 5 1450312 1 TWINE BOX LID 6 1455807 1 TWINE BOX HINGE 7 1410120 1 TWINE BOX COVER W/ INSERTS 8 1452318 1 FRONT CHAIN GUARD 9 1450208 1 FRONT HOUSING 10 1451936 1 HOLE COVER 11 1450250 1 TONGUE 12 1458611 1 JACK STAND TOP WIND 13 1458413 2 FLEXIBLE DRAW LATCH 14 1450397 1 CHAIN DOOR, LH 15 1431565 1 SHAFT TRANSPORT SUPPORT 16 40010000 1 COTTER PIN 17 1437425 1 COMPRESSION SPRING 18 1432535 1 JACK PIN 19 1436782 1 PLASTIC KNOB 20 1432534 1 KNOB STUD 21 3263N13C 6 PANHEAD SCREW 22 360015C 6 EXTERNAL TOOTH LOCKWASHER 23 63121700 6 HEX MACHINE NUT 24 32943C 2 ELASTIC STOP NUT 25 1436016 2 ROLLER BEARING 26 312010H8C 2 BOLT 27 1437433 2 COMPRESSION SPRING 28 1451241 2 SPRING BAR 29 1431625 2 SPRING WASHER 30 49208 2 HAIR PIN COTTER 31 1450332 1 UPPER CROSS PIPE 32 1458601 2 GAS SPRING ASSEMBLY W/ BALL STUDS 33 1451568 2 CHAIN DOOR ROD 34 1458702 1 RUBBER HOLD-DOWN STRAP 35 329023C 18 HEX LOCKNUT 36 02025700 1 BOLT 37 00757908 1 SAFETY CHAIN 38 31102C 32 BOLT 39 6D9016 46 FLANGED WHIZLOCK NUT 40 00023500 16 FLATWASHER 41 1458703 2 RUBBER STOP 42 5E805 2 TYRAP 43 6D9001 4 SHEET METAL SCREW 44 3267F4C 12 FLATHEAD SCREW 45 1430262 1 HINGE PLATE 46 00007800 2 BOLT 47 30078H5C 2 HEX TAP SCREW 48 02931300 2 BOLT 49 1451581 2 ADJUSTING BLOCK 50 32948C 4 ELASTIC STOP NUT 51 00000200 2 HEX NUT 52 00002701 5 FLATWASHER 53 1451562 7 TWINE DIVIDER ROD 54 32902C 4 HEX LOCKNUT 55 49072 2 COTTER PIN 56 31105C 2 BOLT 57 1432500 2 HINGED PLATE 58 00035900 8 BOLT 59 35009C 2 LOCKWASHER 60 3263N4C 18 PANHEAD SCREW 61 312012H5C 2 BOLT 62 000640 2 HEX LOCKNUT 2004 Alamo Group Inc. Parts Section 7
FRONT CHAMBER 2004 Alamo Group Inc. Parts Section 8
FRONT CHAMBER ITEM PART NO. QTY. DESCRIPTION 63 1431556 2 TWINE GUIDE BUSHING 64 35002C 8 LOCKWASHER 65 1438203 2 RETAINING RING 66 1458417 2 HEX INSERT 67 1452390 1 DIVIDER PANEL UPPER 68 1435802 1 MODIFIED COTTER PIN 69 37021C 4 CARRIAGE BOLT 70 00021800 6 HEX NUT 71 32908C 1 HEX LOCKNUT 73 6D9001 4 SHEET METAL SCREW 74 00013901 6 HEX NUT 75 03101646 6 LOCKWASHER 76 37031H5C 6 CARRIAGE BOLT 77 1452081 1 BALE SIZER LH 78 1452080 1 BALE SIZER RH 2004 Alamo Group Inc. Parts Section 9
REAR CHAMBER 2004 Alamo Group Inc. Parts Section 10
REAR CHAMBER ITEM PART NO. QTY. DESCRIPTION 1 6D9001 22 SHEET METAL SCREW 2 1452316 1 CHAIN GUARD, REAR UPPER 3 1410115 1 CHAIN GUARD W/ INSERTS, REAR MIDDLE 4 1410114 1 CHAIN GUARD W/ INSERTS, REAR LOWER 5 1432514 1 HINGED PIN 6 1430262 1 HINGED PLATE 7 42066 2 ROLL PIN 8 6D9016 16 FLANGED WHIZ LOCKNUT 9 3267F4C 12 FLATHEAD SCREW 10 31408C 2 BOLT 11 1435500 2 BEARING CASTING 12 15B800 4 FLATWASHER 13 00001800 4 LOCKNUT 16 1450209 1 REAR HOUSING 17 00023500 18 FLATWASHER 18 35002C 10 LOCKWASHER 19 00035900 18 BOLT 20 300518C 2 HEX TAP BOLT 21 00002700 6 FLATWASHER 22 1431566 2 SPRING ANCHOR PIN 23 1451211 2 SPRING ADJUST LEVER 24 33115C 2 HEX JAM NUT 25 1450144 2 LATCH SPRING ASSEMBLY 26 1434868 2 LATCH PIVOT BUSHING 27 00001400 2 FLATWASHER 28 00752658 2 BOLT 29 35007C 2 LOCKWASHER 30 00007000 2 BOLT 31 00011100 6 FLATWASHER 32 1451040 2 LATCH BAR 33 41954 2 CLEVIS PIN 34 40010000 2 COTTER PIN 35 000640 2 HEX LOCKNUT 36 1457302 2 VINYL TUBE 37 1453280 4 MOUNTING STRAP 38 37033C 2 CARRIAGE BOLT 39 6D9017 4 FLANGED WHIZLOCK NUT 40 02030700 2 BOLT 41 32905C 2 HEX LOCKNUT 42 15B1600 8 FLATWASHER 43 310010H5C 2 BOLT 44 1451248 2 UNLATCH ROD CLEVIS 45 32915C 2 HEX LOCKNUT 46 1457112 2 HYDRAULIC CYLINDER 47 1452519 2 CLEVIS ROD 48 02816800 2 HEX NUT 49 1438449 2 ADJUSTABLE YOKE END 50 1452526 2 UPPER CYLINDER PIN 51 02959924 2 HEX UNI-TORQUE 55 1420105 1 HEX TANK ASSEMBLY LH 56 1420104 1 HEX TANK ASSEMBLY RH 57 1458417 10 HEX INSERT 58 600321 2 SUPPORT CLAMP 59 1457301 4 VINYL TUBE 60 1426784 2 Y-CONNECTOR 61 1426783 Ref. CAP 62 00013300 2 BOLT 2004 Alamo Group Inc. Parts Section 11
UNDERSIDE 2004 Alamo Group Inc. Parts Section 12
UNDERSIDE ITEM PART NO. QTY. DESCRIPTION 1 1450334 2 HOLD-DOWN SUPPORT 2 1450335 2 TELESCOPING PIPE 3 1450333 1 TINE BAR 4 1450137 1 PICK-UP ASSEMBLY (SEE PICK-UP) 5 1450305 1 PICK-UP MOUNT LH 6 1450304 1 PICK-UP MOUNT RH 7 1450306 1 PICK-UP DRIVE SHIELD 8 1456356 1 TAPERLOCK SPROCKET 9 1456357 1 TAPERLOCK BUSHING 10 1451241 2 SPRING BAR 11 1451253 2 ROLLER POSITIONING PLATE 12 1450310 1 PICK-UP SUPPORT, RH 13 1450311 1 PICK-UP SUPPORT, LH 14 1456350 2 SPROCKET 15 1458411 4 MACHINE BUSHING 16 6D5105 2 BEARING CARTRIDGE 17 1450208 Ref FRONT HOUSING FRAME 18 1455500 2 ROLLER HUB 19 1460291 1 ROLLER 20 1452504 1 ROLLER SHAFT 21 6D5249 1 CONNECTOR LINK 22 1456202 1 ROLLER CHAIN 23 1456212 1 ROLLER CHAIN 24 1456208 1 CONNECTOR LINK 25 1438205 1 RETAINING RING 26 1451926 1 ROLLER SHIELD, LH 27 1451925 1 ROLLER SHIELD, RH 28 1450260 1 LOWER HOUSING BRACE 29 1450261 2 SPINDLE MOUNT 30 1452507 2 SPINDLE W/HOLE 31 49033 2 COTTER PIN 32 0536800W 2 SEAL 33 0536005 2 BEARING CONE 34 0536004 2 BEARING CUP 35 0530179 2 HUB AND CUP ASSEMBLY 36 0536002 2 BEARING CUP 37 0536003 2 BEARING CONE 38 0538400 12 DRIVE STUD 39 380451C 2 FLATWASHER 40 33099C 2 HEX SLOTTED NUT 43 0536700 2 HUB CAP 44 0538401 12 STUD NUT 46 1431563 2 COVER MOUNT STUD 47 146160 1 CROSS BEAM COVER 48 60042 6 WIRE ROPE CLAMP 49 42121 6 ROLL PIN 50 1435502 8 CABLE PULLEY 51 42124 1 ROLL PIN 52 1451254 1 CABLE PLATE 53 1457403 1 PICK-UP CABLE 54 29N132 4 CABLE THIMBLE 55 1437523 3 FLATWASHER 56 00002701 3 FLATWASHER 57 1451252 1 IDLER SPACER GUARD 58 1450307 1 CHAIN TENSIONER 59 00001200 14 HEX NUT 61 1457423 1 COMPRESSION SPRING 62 1436357 1 IDLER SPROCKET 63 35009C 1 LOCKWASHER 64 31709H5C 1 BOLT 65 1436005 2 BEARING 66 000130 30 BOLT 2004 Alamo Group Inc. Parts Section 13
UNDERSIDE 2004 Alamo Group Inc. Parts Section 14
UNDERSIDE ITEM PART NO. QTY. DESCRIPTION 67 35003C 32 LOCKWASHER 68 1430320 2 WHEEL ARM 69 1437601 2 WHEEL 70 380010C 4 FLATWASHER 71 49053 2 COTTER PIN 72 1456359 1 SPROCKET 73 49223 2 SAFETY PIN 74 419310 2 CLEVIS PIN 75 10119000 4 BOLT 76 35002C 4 LOCKWASHER 77 00021800 4 HEX NUT 78 40621.25 1 KEY 79 31406C 4 BOLT 80 00752658 4 BOLT 81 02030700 4 BOLT 82 00001400 4 FLATWASHER 83 35007C 8 LOCKWASHER 84 35005C 12 LOCKWASHER 85 00002700 6 FLATWASHER 86 00000200 6 HEX NUT 87 35009C 2 LOCKWASHER 88 1432034 2 WASHER 89 00011100 11 FLATWASHER 90 00013901 4 HEX NUT 91 00749130 4 BOLT 92 312013H5C 2 BOLT 93 02959391 4 BOLT 94 02880900 4 BOLT 95 000640 7 HEX LOCKNUT 96 1457422 1 LEAF SPRING 97 1427420 1 COMPRESSION SPRING 98 312013C 1 BOLT 99 7A10118 4 BOLT 100 00007000 4 BOLT 101 1450159 2 MOUNTED FLOTATION TIRE ASSEMBLY 102 1457800 2 TIRE 103 1457600 2 WHEEL 104 TR415 2 VALVE STEM 105 31202H5C 2 BOLT 106 00035900 2 BOLT 107 380422C 2 FLATWASHER 108 1462384 1 COVER, HAND HOLE 109 1458417 A/R HEX INSERT (INCLUDED IN ITEM 47) 2004 Alamo Group Inc. Parts Section 15
ELEVATOR 2004 Alamo Group Inc. Parts Section 16
ELEVATOR ITEM PART NO. QTY. DESCRIPTION 1 3902A6C 2 SQUAREHEAD CUP POINT SETSCREW 2 00013901 2 HEX NUT 3 1435507 1 DOG CLUTCH, FIXED 4 1436006 1 BALL BEARING 5 1438200 5 RETAINING RING 6 1435508 1 DOG CLUTCH, SLIDING 7 1437423 1 COMPRESSION SPRING 8 1431620 3 WASHER 9 420818 1 ROLL PIN 10 1452541 1 DRIVE SHAFT, FRONT CROSS 11 40641.5 1 KEY 12 1454903 1 SPACER TUBE 13 420511 1 ROLL PIN 14 32905C 13 HEX LOCKNUT 15 1432521 1 ROLLER RACE 16 1435801 1 SPECIAL SOCKETHEAD CAPSCREW 17 1430213 1 LEVER 18 1438406 1 WIRE ROPE THIMBLE 19 00001000 2 WIRE ROPE CLAMP 20 1457401 1 CLUTCH CABLE 21 42121 3 ROLL PIN 22 1435502 3 CABLE PULLEY 23 37051H5C 8 CARRIAGE BOLT 24 1456353 1 SPROCKET(5600 ONLY) 1450389 1 SPROCKET & SHEAVE WLDMT(5690 ONLY) 25 1456010 1 RELUBE FLANGETTE 26 1456016 3 RELUBE BEARING W/ LOCKING COLLAR 27 1456009 1 RELUBE FLANGETTE 28 45053 2 SELF-TAPPING GREASE FITTING 29 3920A29C 6 ALLENHEAD CUP POINT NYLON LOCK SETSCREW 30 1456216 1 ROLLER CHAIN 31 1456217 1 CONNECTOR LINK 32 32908C 2 HEX LOCKNUT 33 31709H5C 1 BOLT 34 1457435 1 TORSION SPRING 35 1451361 1 CHAIN IDLER ARM 36 1454700 1 IDLER SPACER 37 00002701 5 FLATWASHER 38 1437523 2 FLATWASHER 39 1436356 1 IDLER SPROCKET 40 00007800 1 BOLT 41 3922A29C 2 ALLENHEAD CUP POINT NYLON LOCK SETSCREW 42 1456354 1 SPROCKET 43 1455507 2 ELEVATOR DRIVE SPROCKET 44 1435512 2 CHAIN LIMITER 45 00011100 3 FLATWASHER 46 701612C 2 LOCKWASHER 47 00754764 2 BOLT 48 1430261 2 BEARING 49 40652 3 KEY 50 1452544 1 ELEVATOR DRIVESHAFT 51 1432313 2 STRIPPER PLATE 52 1430211 1 FRONT SHAFT COVER 53 3267F4C 12 FLATHEAD SCREW 54 1438430 8 CUPPED SPRING WASHER 55 00021800 19 HEX NUT 56 35002C 13 LOCKWASHER 57 00023500 4 FLATWASHER 58 1456359 1 SPROCKET 59 40651.5 1 KEY 60 370211C 7 CARRIAGE BOLT 61 1434865 7 PIPE SPACER 2004 Alamo Group Inc. Parts Section 17
ELEVATOR 2004 Alamo Group Inc. Parts Section 18
ELEVATOR ITEM PART NO. QTY. DESCRIPTION 62 1431889 1 REAR SHAFT COVER 63 1432517 1 ELEVATOR IDLER SHAFT 64 1432523 53 CHAIN CROSS BAR 65 420913 2 ROLL PIN 66 1455506 2 ELEVATOR CHAIN SLIDING BRACKET 67 1431445 2 CHAIN TENSIONER BRACKET 68 1438440 4 WAVE SPRING WASHER 69 1430220 2 CHAIN GUIDE 70 1438442 6 MACHINE BUSHING 72 1438446 AR MACHINE BUSHING 73 1436009 4 BEARING W/ LOCKING COLLAR 74 1455508 2 ELEVATOR IDLER SPROCKET 75 1436010 2 LOCKING COLLAR 76 1456207 2 ELEVATOR CHAIN W/CONNECTOR LINK 77 1416200 Ref CONNECTOR LINK 78 1416205 Ref ONE BAR CHAIN SECTION 79 1437503 318 WASHER 80 1438202 212 RETAINING RING 81 1456027 106 BALL BEARING 82 35007C 4 LOCKWASHER 83 00752658 4 BOLT 84 32908C 2 HEX LOCKNUT 85 00000200 4 HEX NUT 86 15B1200 4 FLATWASHER 87 1457434 2 COMPRESSION SPRING 88 1452520 2 ELEVATOR CHAIN TENSIONER SCREW 89 6D9007 4 HEX FLANGE WHIZ SCREW 90 1457420 1 COMPRESSION SPRING 91 1452553 1 SPRING CAP 92 3922C3C 1 ALLENHEAD CUP POINT SETSCREW 93 1450235 2 PULLEY MOUNT 94 45051 2 SELF-TAPPING GREASE FITTING 95 9D2010 2 LUBE BULKHEAD NUT 96 9D2009 2 LUBE BULKHEAD CONNECTOR 97 9903 2 PIPE NIPPLE 98 9902 1 PIPE NIPPLE 99 121010 1 PIPE ELBOW 100 3904A7C 2 SQUARE HEAD CUP POINT SETSCREW 101 33115C 2 HEX JAM NUT 102 1454895 1 IDLER ARM PIVOT BUSHING 103 1454699 1 SPACER, SPRING STOP 104 1451303 1 IDLER ARM STOP ANGLE 106 00753642 1 BOLT 107 35003C 1 LOCKWASHER 108 6D9016 1 HEX FLANGE WHIZ LOCKNUT 109 10119000 2 BOLT 110 00002700 4 FLATWASHER 111 02886900 4 CARRIAGE BOLT 112 1456015 1 BEARING, FLANGE (INCLUDES ITEM #26) 113 33117C 1 HEX JAM NUT 114 02845500 1 BOLT 115 1456014 1 FLANGETTE 116 1456013 1 FLANGETTE W/FITTING 2004 Alamo Group Inc. Parts Section 19
HYDRAULIC SYSTEM 2004 Alamo Group Inc. Parts Section 20
HYDRAULIC SYSTEM ITEM PART NO. QTY. DESCRIPTION 1 1457113 1 HYDRAULIC LINE, UPPER RIGHT 2 1457114 1 HYDRAULIC LINE, LOWER RIGHT 3 1457115 1 HYDRAULIC LINE, UPPER LEFT 4 1457116 1 HYDRAULIC LINE, LOWER LEFT 5 2727202 1 HYDRAULIC HOSE W/ PIPE THREADED ENDS 1457214 1 HYDRAULIC HOSE W/FEMALE SWIVEL ONE END 6 1457206 1 HYDRAULIC HOSE 7 1457207 1 HYDRAULIC HOSE 8 1457204 4 HYDRAULIC HOSE 9 1457112 2 HYDRAULIC CYLINDER 10 1457350 1 DOOR LOCK VALVE 11 1437100 1 PICK-UP HYDRAULIC CYLINDER W/PIPE PORTS 1410153 1 PICK-UP HYDRAULIC CYL. W/ORING BOSS PORT 12 1438418 7 2-TWIN CLAMP HALVES 13 1438419 7 TWIN COVER PLATE 16 31106C 7 BOLT 17 1451248 2 UNLATCH ROD CLEVIS 18 00755153 8 COTTER PIN 19 1432525 2 CYLINDER PIN, LOWER 20 1452526 2 CYLINDER PIN, UPPER 21 15B1600 8 FLATWASHER 22 310010H5C 2 BOLT 23 02959924 2 HEX LOCKNUT 24 2437107 1 UNION TEE 25 311010C 2 BOLT 26 1457104 7 ELBOW MALE 90 DEG. W/ O/RING 27 1438420 1 TWIN WELD PLATE 28 6D9016 2 FLANGE WHIZ LOCKNUT 29 17003 3 PIPE CAP 30 1458704 1 GROMMET 31 1457126 1 ADAPTER HYD ELBOW W/PIPE THREADS 02960018 1 ADAPTER HYD ELBOW W/O-RING 32 32907C 2 HEX LOCKNUT 33 33007C 1 HEX NUT 34 1451254 1 CABLE PLATE 35 00001000 1 WIRE ROPE CLAMP 36 1454864 1 TUBE SPACER 37 1451218 1 PICK-UP LIFT CONNECTOR 38 316011H5C 1 BOLT 39 312013H5C 1 BOLT 40 00011100 2 FLATWASHER 41 000640 1 HEX LOCKNUT 42 1450242 1 PICK-UP LIFT CABLE ARM 43 1450340 1 PICK-UP LIFT HOUSING 44 37031C 2 CARRIAGE BOLT 45 6D9017 2 FLANGE WHIZLOCK NUT 46 00000400 1 COTTER PIN 47 1428402 1 THRUST WASHER 48 1450341 1 PICK-UP LIFT SCREW 49 1450154 1 PICK-UP CRANK ASSEMBLY (INCLUDES ITEMS # 51,52 & 53) 50 15007 1 PIPE BUSHING 51 1451352 1 PICK-UP LIFT CRANK 52 1454869 1 PICK-UP LIFT CRANK HANDLE 53 1458414 1 WASHER CUP PUSH NUT 54 1417129 1 BARREL ASSEMBLY 55 1417126 1 FULL LOCKNUT 56 1417132 1 PISTON 57 1 PISTON SEAL 59 1 O-RING 60 141728 1 ROD ASSEMBLY 61 1 O-RING 62 1 BACK-UP 2004 Alamo Group Inc. Parts Section 21
HYDRAULIC SYSTEM 2004 Alamo Group Inc. Parts Section 22
HYDRAULIC SYSTEM ITEM PART NO. QTY. DESCRIPTION 63 1417123 1 LOCK WIRE 64 1417130 1 HEAD 65 1 O-RING 66 1 BACK-UP 67 1 ROD WIPER 1417133 Ref SEAL KIT (INCLUDES ALL ITEMS MARKED*) 1417125 Ref SEAL KIT FOR ITEM #11 68 00726195 1 PIPE 2004 Alamo Group Inc. Parts Section 23
HYDRAULIC SYSTEM 2004 Alamo Group Inc. Parts Section 24
HYDRAULIC SYSTEM ITEM PART NO. QTY. DESCRIPTION 1410153 - HYDRAULIC CYLINDER 1 1 SEAL 2 1 O-RING 3 1 SEAL 4 1 SEAL 5 1 WEAR RING 6 1417147 1 CYLINDER HEAD 7 1417148 1 TUBE WLDMT 8 1417149 1 ROD WLDMT 9 02975532 1 SEAL KIT (CONSIST OF THOSE MARKED WITH *) 10 00756059 1 DECAL-WARNING OIL LEAK (NOT SHOWN) 2004 Alamo Group Inc. Parts Section 25
DUAL TWINE TIE SYSTEM 2004 Alamo Group Inc. Parts Section 26
DUAL TWINE TIE SYSTEM ITEM PART NO. QTY. DESCRIPTION 1 1435501 3 BEARING HOUSING 2 1436005 6 BALL BEARING 3 1436362 1 SPROCKET IDLER SHAFT 4 1438204 5 RETAINING RING 5 1436350 1 SPROCKET DRIVE SHAFT 6 1436425 1 GEAR SHAFT/PINION 7 1436001 2 BUSHING 8 1460155 1 RH TRAVEL PLATE ASSEMBLY (INCLUDES 1 OF ITEMS #9 & #10) 9 1458418 2 PERMANENT STUD 10 42082 2 ROLL PIN 11 1460156 1 LH TRAVEL PLATE ASSEMBLY (INCLUDES 1 OF ITEMS #9 & #10) 12 1450186 1 CHAIN COVER STUD SUB-ASSEMBLY (INCLUDES 4 OF ITEM #55) 13 1450324 1 RH TWINE TRAVEL LIMIT 14 1450325 1 LH TWINE TRAVEL LIMIT 15 1451174 4 KNIFE STRAP 16 31104H5C 2 BOLT 17 00021800 14 HEX NUT 18 37021H5C 4 CARRIAGE BOLT 19 6D9016 8 FLANGED WHIZLOCK NUT 20 1450390 1 CHAIN BEAM 21 1451048 2 TWINE HOOK-WHITE 22 1451173 2 LATCH, TRAVEL 23 1451175 2 KNIFE CARRIER 24 1451353 1 CHAIN GUIDE 25 1451569 2 SPACER, KNIFE CARRIER 27 1456219 2 ROLLER CHAIN 28 1456782 4 SLIDER 29 1457427 2 EXTENSION SPRING 30 1458409 1 CARRIAGE BOLT 31 10062000 8 BOLT 32 31102H5C 9 BOLT 33 00035900 4 BOLT 34 10119000 2 BOLT 35 10121000 2 BOLT 36 32901C 2 HEX LOCKNUT 37 32902C 8 HEX LOCKNUT 38 32942C 2 ELASTIC STOP NUT 39 00024000 6 HEX NUT 40 33111C 2 HEX JAM NUT 41 00017000 6 LOCKWASHER 42 00011700 13 LOCKWASHER 43 370010C 4 INTERNAL TOOTH LOCKWASHER 45 37022C 3 CARRIAGE BOLT 47 380419C 8 FLATWASHER 48 6D5206 2 CONNECTING LINK 49 6D5283 2 OFFSET LINK 50 1436775R 1 PLASTIC GEAR 51 1456783 1 DRIVE PULLEY 52 00023500 5 FLATWASHER 53 40621 1 KEY 54 1438204 2 RETAINING RING 55 1458419 4 PERMANENT STUD 56 4062.56 1 KEY, GEAR 57 24022 1 SHOULDER BOLT 58 1457429 1 TORSION SPRING, COUNTER 59 1438606 1 COUNTER 60 1452192 1 COUNTER MOUNTING BRACKET 61 3272P5C 4 MACHINE SCREW 62 33025C 4 HEX MACHINE NUT 63 37003C 4 INTERNAL TOOTH LOCKWASHER 64 1452193 1 COUNTER COVER 65 1430193 2 KNIFE BLADE ASSEMBLY 2004 Alamo Group Inc. Parts Section 27
DUAL TWINE TIE SYSTEM 2004 Alamo Group Inc. Parts Section 28
DUAL TWINE TIE SYSTEM ITEM PART NO. QTY. DESCRIPTION 66 3263R2C 4 PHILLIP HEAD SCREW 67 1450166 1 TWINE DRIVE ASSEMBLY 68 1451930 1 TWINE GUIDE BRACKET 69 1431556 2 TWINE GUIDE BUSHING 70 1438203 2 RETAINING RING 71 00021400 2 BOLT 72 11D9005 2 FLANGED WHIZLOCK NUT 73 340211C 2 WING NUT 74 1437426 2 COMPRESSION SPRING 75 1452184 2 DUAL TWINE BRAKE 76 1458409 2 CARRIAGE BOLT 77 1438205 3 RETAINING RING 78 1431354 1 CHAIN GUIDE 2004 Alamo Group Inc. Parts Section 29
DUAL TWINE DRIVE ASSEMBLY 2004 Alamo Group Inc. Parts Section 30
DUAL TWINE DRIVE ASSEMBLY ITEM PART NO. QTY. DESCRIPTION 1 11D9005 2 FLANGED WHIZ NUT 2 1426426 1 SPUR GEAR, 12 TEETH 3 1427050 1 ELECTRIC MOTOR 4 1451628 1 MOTOR MOUNT 5 330211C 2 HEX MACHINE NUT 6 360014C 2 EXT TOOTH LOCKWASHER 7 42035 1 ROLL PIN 8 1434851 2 BEARING CAGE 9 1436002 2 BEARING 10 1438200 2 RETAINING RING 11 1438202 2 RETAINING RING 12 1450367 1 LOWER IDLER ARM 13 1452532 2 IDLER SHAFT 14 31075C 2 BOLT 15 1450368 1 UPPER IDLER ARM 16 1436003 1 BEARING 17 1436005 1 BALL BEARING 18 1452530 1 SHAFT, FEED ROLLER 19 1452531 1 FEED ROLLER, DUAL TWINE 20 1456425 1 MODIFIED SPUR GEAR, 60 TEETH 21 1458200 1 EXTERNAL RETAINING RING 22 10058000 3 BOLT 23 00017000 6 LOCKWASHER 24 1450366 1 MOUNTING BRACKET 25 1457428 2 EXTERNAL SPRING 26 31002H5C 5 BOLT 27 314017C 1 BOLT 28 00001200 1 HEX NUT 30 1431556 2 TWINE GUIDE BUSHING 31 1438203 2 RETAINING RING 32 1451930 1 TWINE GUIDE BRACKET 33 00024100 2 FLATWASHER 34 37021H5C 2 CARRIAGE BOLT 35 6D9016 3 FLANGED WHIZ LOCKNUT 36 00021400 2 BOLT 2004 Alamo Group Inc. Parts Section 31
WRAP INSERT 2004 Alamo Group Inc. Parts Section 32
WRAP INSERT ITEM PART NO. QTY. DESCRIPTION 1 1456300 1 PULLEY 2 3919A2C 1 SOCKET HEAD SETSCREW 3 1456103 1 V-BELT 4 00002700 4 FLATWASHER 5 2F031 2 BELT IDLER 6 00749130 2 BOLT 7 00999418 1 BOLT 8 32905C 4 LOCKNUT 9 1451270 1 IDLER PULLEY ARM 10 1454879 1 IDLER BUSHING RS 11 1457436 1 TORSION SPRING CLUTCH 12 1452051 1 PANEL, LOWER DIVIDER 13 00021800 33 NUT 14 35002C 32 LOCKWASHER 15 00002000 3 BOLT 16 35003C 3 LOCKWASHER 17 1432034 3 CLUTCH RETAINING WASHER 18 6D5103A 10 FLANGETTE 19 6D5113 5 BEARING 20 1451186 1 CLUTCH BRACKET 21 37021H5C 20 CARRIAGE BOLT 22 1452533 1 CAM SHAFT 23 00035900 3 BOLT 24 1451121 1 BRACKET, HALL EFFECT 25 1457932 1 CLUTCH - MODIFIED 26 1454885 2 SPACER 27 1450195 1 CUTT-OFF CAM ASSEMBLY 27A 1450372 1 CAM 27B 3919A9C 3 SOCKET HEAD SETSCREW 27C 5C5180 3 JAM NUT 27D 42069 1 ROLL PIN 28 1452198 1 BRACKET, CAM SWITCH 29 00023500 1 FLATWASHER 31 6D9016 1 FLANGE LOCKNUT 32 MWSN1192 2 EXTENSION SPRING 33 1450393 2 IDLER ARM BASE 34 1450374 2 SWING ARM 35 1438203 2 RETAINING RING 36 1450194 1 IDLER ROLLER ASSEMBLY 36A 1456007 2 BEARING 36B 1454892 1 IDLER ROLLER 37 1460201 1 NET CHUTE 38 1450184 1 DRIVE ROLLER ASSEMBLY 39 1460208 1 END PLATE, RH 40 7A5188 2 BOLT 41 1460100 1 COUNTER RING ASSEMBLY 42 1450177 1 TRIP ARM ASSEMBLY 42A 1436016 1 ROLLER BEARING 42B 1450378 1 TRIP ARM 43 31207H5C 2 BOLT 44 32903C 1 LOCKNUT 45 311012H5C 1 BOLT 46 1454884 1 STOP, TORSION SPRING 47 1458707 1 BUMPER 48 49023 2 COTTER PIN 49 1457431 1 TORSION SPRING, RH 50 1460101 1 CUTTER BAR ASSEMBLY 50A 1428350 5 KNIFE 50B 3981H1C 13 BOLT 50C 380419C 13 FLATWASHER 50D 1460200 1 CUTTER BAR 51 1454880 1 IDLER BUSHING LS 2004 Alamo Group Inc. Parts Section 33
WRAP INSERT 2004 Alamo Group Inc. Parts Section 34
WRAP INSERT ITEM PART NO. QTY. DESCRIPTION 52 1457430 1 TORSION SPRING, LH 53 1456102 1 V-BELT 54 31407H5C 1 BOLT 55 1456011 2 FLANGETTE 56 1456012 1 BEARING 57 1457902 1 CLUTCH 58 312020H5C 1 BOLT 59 6D9017 3 FLANGE LOCKNUT 60 1450188 1 END PLATE ASSEMBLY, LH 61 00011100 2 FLATWASHER 62 00013901 2 HEX NUT 63 1454894 1 SPACER 64 1461207 1 IDLER PULLEY ARM, RS 65 380434C 1 FLATWASHER 66 1451115 1 BELT TENSIONER BRACKET 2004 Alamo Group Inc. Parts Section 35
WRAP ROLL MOUNTING SYSTEM - MODEL 5690 2004 Alamo Group Inc. Parts Section 36
WRAP ROLL MOUNTING SYSTEM - MODEL 5690 ITEM PART NO. QTY. DESCRIPTION 1 00035900 6 BOLT 2 70014W 1 PLASTIC KNOB 3 1450275 1 ROLL LATCH HANDLE 4 1451561 1 TENSION ROD 5 1450276 1 HANDLE PIVOT BRACKET 6 6D9016 6 FLANGE LOCKNUT 7 42049 1 ROLL PIN 8 1455503 2 ROLL END STOP 9 1450271 1 ROLL LATCH 10 1438447R 1 HOIST EYE 11 00024000 2 HEX NUT 12 1427422 1 EXTENSION SPRING 13 11D9005 2 HEX FLANGE NUT 14 31006H5C 1 BOLT 15 1450600 2 ROLL TUBE MOUNTING 16 1450315 1 ROLL MOUNTING TUBE 17 1451916 3 SPACER WASHER 18 1426790 A/R ROLL/NETTING 2004 Alamo Group Inc. Parts Section 37
PICK-UP 2004 Alamo Group Inc. Parts Section 38
PICK-UP ITEM PART NO. QTY. DESCRIPTION 1 1432034 4 WASHER 3 1450301 1 PICK-UP FRAME 4 1450302 1 END PLATE, RH 5 1450303 1 END PLATE, LH 6 1450304 1 PICK-UP MOUNT, RH 7 1450305 1 PICK-UP MOUNT, LH 8 1452041 1 WINDROW GUIDE SHIELD, RH 9 1452042 1 WINDROW GUIDE SHIELD, LH 10 1452189 21 PICK-UP BAND 11 1455505 1 PICK-UP CAM 12 1456005 2 BALL BEARING 13 1456006 4 BEARING FLANGETTE 14 1437434 55 PICK-UP TINE, DOUBLE SPRING 15 1450300 2 BEARING PLATE 16 29N132 2 THIMBLE 17 000130 1 BOLT 18 00753642 14 BOLT 19 02030700 6 BOLT 20 35003C 17 LOCKWASHER 21 35005C 6 LOCKWASHER 22 37021C 4 CARRIAGE BOLT 23 00023500 4 FLATWASHER 24 40621.25 1 KEY 25 450022 1 GREASE FITTING 26 6D9003 27 SHEET METAL SCREW 27 6D9007 63 HEX FLANGE SCREW 28 6D9016 4 FLANGE WHIZ LOCKNUT 29 00013901 10 HEX NUT 30 1450299 1 PICK-UP SHAFT 31 1451095 5 TINE BAR CAM ARM 32 1451114 55 TINE SUPPORT ANGLE 33 1451739 55 PICK-UP TINE 34 1456004 5 BALL BEARING 35 02845500 5 BOLT 36 32907C 5 HEX LOCKNUT 37 35007C 5 LOCKWASHER 38 32972H5C 55 HEX LOCKNUT 39 37027H5C 55 CARRIAGE BOLT 40 02970595 5 BOLT 41 00007000 5 BOLT 42 380460C 5 FLATWASHER 43 1456002 2 BUSHING 44 1456003 2 BUSHING 45 1450298 5 TINE BAR 46 31202H5C 2 BOLT 47 00015800 10 LOCKNUT 2004 Alamo Group Inc. Parts Section 39
GEARBOX 2004 Alamo Group Inc. Parts Section 40
GEARBOX ITEM PART NO. QTY. DESCRIPTION 1 1416658 1 CASING 2 2716659 2 SHIM 3 2716602 2 BEARING 4 1416659 1 SHAFT 5 2716740 1 SNAP RING 6 00752931 1 PLUG 7 2716658 2 BEARING 8 2716607 2 SNAP RING 9 2716660 3 OIL SEAL 10 1416660 1 CROWN WHEEL 11 2716662 2 SHIM 12 70809C8 4 BOLT 13 1416661 1 EXTENSION 14 1416662 1 PINION SHAFT 15 00756649 1 SNAP RING 16 61368C8 4 BOLT 17 1416657 1 DIPSTICK PLUG 18 1416663 1 SHIM 19 2716557 1 PLUG 20 710850 1 KEY 21 00011400 2 BOLT 22 00011100 2 FLATWASHER 23 1456779 1 GUARD 24 03101646 2 LOCKWASHER 25 00013901 2 HEX NUT 26 00756373 4 BOLT 27 00010300 4 LOCKWASHER 28 1456410 1 GEARBOX COMPLETE - LESS ITEM #20 - #27 2004 Alamo Group Inc. Parts Section 41
GEARBOX 2004 Alamo Group Inc. Parts Section 42
GEARBOX ITEM PART NO. QTY. DESCRIPTION 1 00011400 2 HEX CAPSCREW 2 00011100 2 FLATWASHER 3 1456779 1 GUARD 4 03101646 2 LOCKWASHER 5 00013901 2 HEX NUT 6 1438202 1 SEAL 7 K9115410 1 RETAINING RING 8 K9111340 FLATWASHER K9111330 FLATWASHER K9111320 FLATWASHER K9111300 FLATWASHER 9 2716539 1 BALL BEARING 10 K9116680 1 RETAINING RING 11 K2730810 1 GEAR COVER 12 K1510420 1 GEARBOX GASKET 13 61368C8 6 HEX CAPSCREW 14 00754577 6 LOCKWASHER 15 00756373 4 HEX CAPSCREW 16 00010300 4 LOCKWASHER 17 K9321930 1 BEARING 18 K9108910 FLATWASHER K9108900 FLATWASHER K9108890 FLATWASHER 19 K2730280 1 GEAR SHAFT 20 K2804351 1 GEAR HOUSING 21 710850 3 KEY 22 K2800042 1 DRIVE SHAFT 23 K2730290 1 GEAR 24 K9363390 2 SEAL 25 K9116730 2 RETAINING RING 26 K9109640 FLATWASHER K9109630 FLATWASHER K9109620 FLATWASHER K9109650 FLATWASHER 27 K9301670 2 BALL BEARING 28 K9060400 2 PLUG 29 K9107270 1 FLATWASHER 30 1456401 1 GEARBOX COMPLETE, LESS ITEM #1-5, 15,16 & (2) #21 2004 Alamo Group Inc. Parts Section 43
DRIVELINE 540 RPM (P/N 1456404) ITEM PART NO. QTY. DESCRIPTION 1 1416591 1 YOKE 2 8388 2 CROSS BEARING KIT 3 00756934 2 ROLL PIN 4 8982 1 INBOARD YOKE 5 2116431 1 INNER PROFILE 6 1416606 1 OUTER PROFILE & SLEEVE W. A. 7 1416595 1 INBOARD YOKE 8 0921000460 1 FRICTION CLUTCH 9 1416597 1 SHIELD CONE, 6 RIBBED 10 1416608 1 OUTER SHIELD TUBE, OVAL 11 1416609 1 INNER SHIELD TUBE, ROUND 12 1416409 2 BEARING RING 13 1416412 1 SAFETY CHAIN 14 2738315 1 DECAL, IID SHIELD 15 2738320 1 DECAL, IID SHIELD REMOVED 16 1416438 2 SCREW 17 1416600 1 SUPPORT BEARING 18 1416601 2 GREASE FITTING 19 1416613 1 SHIELD CONE, 6 RIBBED 20 1416586 1 REPAIR KIT, SLIDE LOCK YOKE 21 1416614 1 IID HALF ASSEMBLY W/SHIELD, TRACTOR END 22 1416615 1 IID HALF ASSEMBLY W/SHIELD & CLUTCH, BALER END 2004 Alamo Group Inc. Parts Section 44
CLUTCH 540 RPM (P/N 0921000460) ITEM PART NO. QTY. DESCRIPTION 1 8416 1 CLUTCH HOUSING 2 0921000462 4 FRICTION DISK 3 8375 1 HUB 4 8376 1 DRIVE PLATE 5 8377 1 DRIVE PLATE 6 8465 1 THRUST PLATE 7 8378 1 BELLEVILLE SPRING 8 8425 4 HEX NUT 9 1416620 1 BACK-UP SPRING 10 1416423 3 BALL 11 1416424 1 COMPRESSION SPRING 12 1416425 1 LOCK COLLAR 13 1416621 1 FLANGED RING 14 1416622 1 SNAP RING 15 092100468 1 BELLEVILLE SPRING 16 0921000470 1 Q. D. FLANGE KIT (INCLUDES ITEMS 9-14) 2004 Alamo Group Inc. Parts Section 45
DRIVELINE 1000 RPM 2004 Alamo Group Inc. Parts Section 46
DRIVELINE 1000 RPM ITEM PART NO. QTY. DESCRIPTION 1456407 OPTIONAL CONSTANT VELOCITY IID SHAFT, 1000 RPM W/ CLUTCH 1 1416627 1 SLIDE COLLAR YOKE SPLINE 2 1416628 1 GREASE FITTING 3 1416629 1 DOUBLE YOKE 4 1416630 1 INBOARD YOKE 5 1416631 2 CROSS AND BEARING KIT 6 00756934 2 ROLL PIN 7 8388 1 CROSS AND BEARING KIT 8 1416632 1 INNER SHAFT 9 1416633 1 OUTER SHAFT & SLEEVE 10 1416595 1 INBOARD YOKE 11 1416607 1 FRICTION CLUTCH 12 1416409 2 BEARING RING 13 1416634 1 OUTER SHIELD 14 1416599 1 INNER SHIELD 15 1416635 1 CONSTANT VELOCITY CONE & BEARING ASSEMBLY 16 1416636 1 SHIELD CONE, 3 RIBBED 17 1416597 1 SHIELD CONE, 6 RIBBED 18 1416412 1 SAFETY CHAIN 19 2738315 1 DANGER DECAL, OUTER (INCLUDED IN ITEM 13) 20 2738320 1 DANGER DECAL, INNER (INCLUDED IN ITEM 9) 21 1416438 8 SCREW (INCLUDED IN ITEMS 15, 16 & 17) 22 1416600 1 SUPPORT BEARING 23 1416601 1 GREASE FITTING 1416586 Ref SLIDE LOCK YOKE REPAIR KIT (PART OF ITEM 1) 1416441 Ref QUICK DISCONNECT FLANGE KIT (INCLUDES ITEMS 24,31,33,34,35,36 - PART OF ITEMS 11) 24 1416622 1 SNAP RING 25 1416617 1 CLUTCH HOUSING 26 1416431 2 FRICTION DISK LINING 27 1416618 1 HUB 28 2116450 1 THRUST PLATE 29 1416619 1 BELLEVILLE SPRING, WHITE 30 2116451 1 BELLEVILLE SPRING, RED 31 1416423 3 BALL 32 2116452 4 NUT 33 1416620 1 BACK-UP RING 34 1416424 1 COMPRESSION RING 35 1416425 1 LOCK COLLAR 36 1416621 1 FLANGED RING 2004 Alamo Group Inc. Parts Section 47
WIRING DIAGRAM - MODEL 5690 2004 Alamo Group Inc. Parts Section 48
WIRING DIAGRAM - MODEL 5690 ITEM PART NO. QTY. DESCRIPTION 1 1457932 1 CLUTCH, MODIFIED 2 1457942 1 HARNESS, HALL EFFECT 3 1460209 1 SWITCH 4 1450249 2 SWITCH - HARNESS 5 1457929 1 HARNESS 6 1427050 1 MOTOR 7 1457943 1 SENSOR HARNESS 8 1457902 1 CLUTCH 9 33029C 8 HEX NUT 10 37005C 12 LOCKWASHER 11 3259N10C 4 PANHEAD SCREW 12 1457936 1 HARNESS, CONTROL CORD 13 1457945 1 CONTROL BOX 14 1451120 1 BRACKET, CONTROLLER 15 1458708 2 ANTI PIVOT WASHER 16 1456776 2 KNOB 17 1458424 2 NYLON JAM NUT 18 1431170 2 SWITCH BRACKET 19 3276H5C 4 HEX MACHINE SCREW 20 360015C 4 LOCKWASHER 21 380413C 4 FLATWASHER 22 3274F10C 4 MACHINE SCREW 23 31102C 3 BOLT 24 600321 6 CLAMP, SUPPORT 25 32902C 3 HEX LOCKNUT 2004 Alamo Group Inc. Parts Section 49
BALE COUNT SENSOR - MODEL 5690 2004 Alamo Group Inc. Parts Section 50
BALE COUNT SENSOR - MODEL 5690 ITEM PART NO. QTY. DESCRIPTION 1 1414201 1 BRACKET, DOOR HINGE MAGNET 2 31104H5C 2 BOLT 3 1457928 1 ACTUATOR 4 3257N7C 2 FLATWASHER 5 38045C 2 FLATWASHER 6 37003C 2 LOCKWASHER 7 33025C 2 HEX MACHINE NUT 8 1457943 1 SENSOR, MAGNETIC 9 3257N7C 2 MACHINE SCREW 10 38045C 2 FLATWASHER 11 37003C 2 LOCKWASHER 12 33025C 2 HEX MACHINE NUT 13 1451125 1 BRACKET, DOOR OPEN SENSOR 14 3263N9C 2 MACHINE SCREW 15 380413C 2 FLATWASHER 16 360015C 2 LOCKWASHER 17 63121700 2 HEX MACHINE NUT 18 1451947 1 SHIELD, DOOR OPEN SENSOR 19 10058000 2 BOLT 20 00024100 2 FLATWASHER 21 11D9005 2 FLANGED LOCKNUT 22 6D9016 2 FLANGED LOCKNUT 2004 Alamo Group Inc. Parts Section 51
ELECTRICAL SYSTEM - MODEL 5600 2004 Alamo Group Inc. Parts Section 52
ELECTRICAL SYSTEM - MODEL 5600 ITEM PART NO. QTY. DESCRIPTION 1 33029C 4 HEX NUT 2 37005C 8 LOCKWASHER 3 380413C 4 FLATWASHER 4 360015C 4 EXTERNAL TOOTH LOCKWASHER 5 3276H5C 4 HEX MACHINE SCREW 6 3274F10C 4 SLOTTED FLATHEAD MACHINE SCREW 7 1431170 2 SWITCH BRACKET 8 31102H5C 3 BOLT 9 600321 6 CLAMP 10 32902C 3 HEX LOCKNUT 11 1450249 2 SWITCH HARNESS 12 1457915 1 WIRE HARNESS, BALER END 13 5E805 9 TYRAP 14 0138629 1 TYRAP 15 1456778 4 BEADED TIE 16 1450175 1 CONTROL HOUSING ASSEMBLY 17 1451120 1 BRACKET-CONTROLLER 18 1456776 2 KNOB 19 1458708 2 ANTI-PIVOT WASHER 2004 Alamo Group Inc. Parts Section 53
ELECTRICAL SCHEMATIC - MODEL 5690 ITEM PART NO. QTY. DESCRIPTION - - ELECTRICAL SCHEMATIC - MODEL 5690 2004 Alamo Group Inc. Parts Section 54
ELECTRICAL SCHEMATIC - MODEL 5600 ITEM PART NO. QTY. DESCRIPTION - - ELECTRICAL SCHEMATIC - MODEL 5600 2004 Alamo Group Inc. Parts Section 55
STANDARD SAFETY LIGHTS 2004 Alamo Group Inc. Parts Section 56
STANDARD SAFETY LIGHTS ITEM PART NO. QTY. DESCRIPTION 1 1457937 1 DUAL LAMP (RH) 2 1457938 1 DUAL LAMP (LH) 3 10058000 8 BOLT 4 32901C 8 LOCKNUT 5 1457939 1 MAIN HARNESS 6 1457944 1 WISHBONE HARNESS 7 600343 3 SUPPORT CLAMP 8 5E805 8 TYRAP 9 2427905 1 MALE PLUG 10 2427904 1 SPRING 11 1417917 2 AMBER LENS 12 1417916 1 RED LENS 13 1417918 2 LIGHT BULB 14 1417919 1 BLACK BLANK 15 1417915 1 FRONT HOUSING 16 1417914 1 REAR HOUSING 2004 Alamo Group Inc. Parts Section 57
RAMP CABLE LIFT (RIGHT & LEFT) ITEM PART NO. QTY. DESCRIPTION 1 1452555 2 PIN, CABLE ARM PIVOT 2 1457409 2 CABLE 3 1451315 2 CABLE ARM 4 60042 8 CLAMP 5 1460239 2 CABLE ARM SUPPORT 6 1457437 1 SPRING 7 6D9001 6 SCREW 8 310010H5C 2 BOLT 9 02959924 2 LOCKNUT 10 00011100 2 FLATWASHER 11 29N132 2 THIMBLE, CABLE 12 1432034 2 WASHER 13 35003C 2 LOCKWASHER 14 00013901 2 NUT 15 1837420 1 SPRING, (NOT SHOWN) 16 00007000 2 BOLT 17 1452554 2 SPACER, THIMBLE 2004 Alamo Group Inc. Parts Section 58
BALE RAMP EXTENSION ITEM PART NO. QTY. DESCRIPTION 1 1450385 1 RAMP EXTENSION 2 1450386 2 UPPER EXTENSION PIPE PIVOT PLATE 3 1451274 2 LOWER EXTENSION PIPE PIVOT PLATE 4 1451299 1 R. TORQ ROD ROLLER PLATE 5 1451300 1 L. TORQ ROD ROLLER PLATE 6 02957009 4 BOLT 7 00753642 4 BOLT 8 00013901 4 NUT 9 03101646 4 LOCKWASHER 10 45051 2 GREASE FITTING 11 6D9017 4 FLANGED WHIZ LOCKNUT 2004 Alamo Group Inc. Parts Section 59
RAMP CHANNEL 2004 Alamo Group Inc. Parts Section 60
RAMP CHANNEL ITEM PART NO. QTY. DESCRIPTION 1 1432034 2 WASHER 2 1450180 1 RIGHT TORSION ROD 3 1450181 1 LEFT TORSION ROD 4 1450384 1 BALE RAMP 5 1450387 2 EXTENSION PIPE STOP 6 1451180 2 TORQ ROD MAIN SUPPORT PAD 7 1451181 1 TORQ ROD CENTER SUPPORT PAD 8 1451359 2 TORQUE ROD END CLAMP 9 1451360 2 TORQUE ROD END BLOCK 10 1452527 2 SPRING ROD 11 1454873 2 RAMP PIVOT BUSHING 12 1456788 4 TORSION ROD MAIN SUPPORT 13 1456789 2 TORSION ROD CENTER SUPPORT 14 1457409 Ref CABLE 15 1457434 2 COMPRESSION SPRING 16 1458705 2 RUBBER DONUT CUSHION 17 2728400 4 FLANGED TOP LOCKNUT 18 29N132 2 CABLE THIMBLE 19 02152800 2 BOLT 20 02044900 4 BOLT 21 00011400 10 BOLT 22 000245 2 BOLT 23 02880900 2 BOLT 24 32905C 2 LOCKNUT 25 32908C 2 LOCKNUT 26 00021800 6 NUT 27 00013901 8 NUT 28 00000200 4 NUT 29 00011700 6 LOCKWASHER 30 03101646 10 LOCKWASHER 31 00002700 2 FLATWASHER 32 35009C 2 LOCKWASHER 33 00002701 2 FLATWASHER 34 15B1200 2 FLATWASHER 35 60042 Ref WIRE ROPE CLAMP 36 00000200 2 NUT 37 15B1200 2 FLATWASHER 2004 Alamo Group Inc. Parts Section 61
OPTIONAL - WINDROW GATHERING WHEEL 2004 Alamo Group Inc. Parts Section 62
OPTIONAL - WINDROW GATHERING WHEEL ITEM PART NO. QTY. DESCRIPTION 1450439 - WINDROW GATHERING WHEEL ASSY 1 1458709 2 GATHERING WHEEL 2 1451098 2 FLANGE CLAMP PLATE 3 1460312 2 WHEEL HUB 4 00007000 16 BOLT 5 000640 16 LOCKNUT 6 1460307 1 R. SPINDLE 1460308 1 L. SPINDLE 7 00013900 2 BOLT 8 32943C 2 ELASTIC STOP NUT 9 1461009 1 R. STRIPPER & HAY STRAP 10 00023100 4 BOLT 11 00011100 8 FLATWASHER 12 03101646 8 LOCKWASHER 13 00013901 8 HEX NUT 14 1460310 1 R. WHEEL ARM 1460311 1 L. WHEEL ARM 15 1460315 2 PIVOT PIN 16 1460313 1 R. MOUNT BRACKET 1460314 1 L. MOUNT BRACKET 17 00753642 4 BOLT 18 10119000 2 BOLT 19 00011700 2 LOCKWASHER 20 00021800 2 HEX NUT 21 45051 4 GREASE FITTING 22 1456022 4 BUSHING 23 1456023 4 BUSHING 24 1452586 2 UPPER LIFT ROD 25 02816800 2 HEX NUT 26 1460309 2 LIFT TUBE 27 1452590 2 LOWER LIFT ROD 28 1457440 2 SPRING 29 42088 2 ROLL PIN 30 40010000 2 COTTER PIN 31 00002700 2 FLATWASHER 32 49207 2 HAIR PIN COTTER 33 1458431 2 THRUST WASHER 34 1438442 2 MACHINE BUSHING 35 00034300 2 RETAINING RING 2004 Alamo Group Inc. Parts Section 63
WIRE HARNESS ROUTING 2004 Alamo Group Inc. Parts Section 64
WIRE HARNESS ROUTING ITEM PART NO. QTY. DESCRIPTION 1 1457915 1 WIRE HARNESS - BALER END 2 1457944 1 WISHBONE WIRE HARNESS 3 5E805 15 TY-RAP,.091 X 8" 4 1462354 2 CHANNEL, HARNESS SUPPORT 2004 Alamo Group Inc. Parts Section 65
OPTIONAL 1000 RPM CONVERSION KIT (1450424) ITEM PART NO. QTY. DESCRIPTION 1 1456218 1 CONNECTOR LINK 2 1456217 1 ROLLER CHAIN 3 1456358 1 SPROCKET 4 1456407 1 CV IID ASSEMBLY (SEE 1000 RPM DRIVELINE) 5 3904A7C 2 SQUARE HEAD CUP POINT SETSCREW 6 33115C 2 JAM NUT NOTE: All components 1. Open the 2. Install the 3. Replace the 2004 Alamo Group Inc. Parts Section 66
TO THE OWNER/OPERATOR/DEALER To keep your implement running efficiently and safely, read your manual thoroughly and follow these directions and the Safety Messages in this Manual. The Table of Contents clearly identifies each section where you can easily find the information you need. The OCCUPATIONAL SAFETY AND HEALTH ACT (1928.51 Subpart C) makes these minimum safety requirements of tractor operators: REQUIRED OF THE OWNER: 1. Provide a Roll-Over-Protective Structure that meets the requirements of this Standard; and 2. Provide Seatbelts that meet the requirements of this paragraph of this Standard and SAE J4C; and 3. Ensure that each employee uses such Seatbelt while the tractor is moving; and 4. Ensure that each employee tightens the Seatbelt sufficiently to confine the employee to the protected area provided by the ROPS. REQUIRED OF THE OPERATOR 1. Securely fasten seatbelt if the tractor has a ROPS. 2. Where possible, avoid operating the tractor near ditches, embankments, and holes. 3. Reduce speed when turning, crossing slopes, and on rough, slick, or muddy surfaces. 4. Stay off slopes too steep for safe operation. 5. Watch where you are going - especially at row ends, on roads, and around trees. 6. Do not permit others to ride. 7. Operate the tractor smoothly - no jerky turns, starts, or stops. 8. Hitch only to the drawbar and hitch points recommended by the tractor manufacturer. 9. When the tractor is stopped, set brakes securely and use park lock, if available. Keep children away from danger all day, every day... Equip tractors with rollover protection (ROPS) and keep all machinery guards in place... Please work, drive, play and live each day with care and concern for your safety and that of your family and fellow citizens.
Round Balers Pub 10-01 Printed U.S.A. P/N 4895WP