2650 BALEBUSTER Exclusive Features available ONLY on the 2650 BALEBUSTER Heavy-Duty Flails and High Speed Rotor: The 2650 features an oil bath chain case to reverse the direction of the PTO, increasing the speed and efficiency of the rotor by 20%! Patented shredder chamber with adjustable slug bars and 3 chain slat conveyor. Combining these features with the heavy duty flails and high speed rotor, the 2650 shredder chamber will process bales in any condition.wet, frozen, old, new, or with flat bottoms. The conveyor is slanted so it helps feed the hay/straw into the rotor. The adjustable slugbar allows the operator to adjust the length of the cut, even with a bale in the chamber. Right side discharge. Tractor hydraulic controls are located on the right side, the 2650 s right hand discharge makes it easy to look over your right shoulder and keep your hand on the controls. Two stage bale loader: The 2650 speeds up the loading process by allowing each bale to be lifted separately without disturbing the other bales. The bale loader also carries a second bale, to increase productivity.
Processing is a better way of feeding hay because: - Chops the forages into selected lengths - Mixes drier, outside layers with fresher, inner layers - Removes dust and molds - Makes your hay go further by preventing cattle from sorting WHY A BALEBUSTER? Haybuster owners tell us they save over 25% in hay usage when bales are processed rather than letting livestock pull and sort hay from densely packed or frozen, unprocessed bales. Processing straw offers these benefits: -Removes most of the twine. -Saves wear and tear on tractors and loaders. -There s less manure to haul. -Keeps your livestock clean and comfortable. -Allows you to apply bedding when needed, not just when scheduled. Uniformity is a BIG advantage with the 2650. From start to finish, the 2650 puts out a consistent windrow. This ensures that each animal gets its fair share. When you re bedding a barn or pen, the 2650 applies the straw more evenly, completing the job faster and saving you money. It s a Cadillac. It s everything that you advertise it to be and better. Excellent! I was feeding 300 head when I got the 2650. Within a week, I was feeding two less bales...figuring out to be a savings of about $97 a day at $65 a ton. Don t wait as long as I did to buy one, because you can sure save a lot of hay. There s a lot less waste and the cows utilize it a lot better. Kyle Palmer, Hinsdale, Montana I m very impressed with the way the 2650 shreds hay and spreads straw. Excellent machine! Randy Fleck, Lampman, Saskatchewan
WHEN IT S RIGHT IT S NATURAL! Because the tractor s console is on the right side, it just makes sense to have the discharge on the right side too. This gives you better visibility of the output and reduces fatigue. THE RIGHT DEFLECTOR Adjusting the deflector on the 2650 is a one handed operation. The latch requires only one hand because the torsion springs support the bulk of the deflector s weight, allowing you to set the deflector to the desired position with very little effort. The optional hydraulic deflector allows the operator to set the deflector position directly from the tractor cab.
THE SECRET IS STILL THE SHREDDER CHAMBER The 2650 s Shredder Chamber: -Is one of the easiest to operate. Just load a bale into the shredder chamber and go! Rarely do you have to reverse bale rotation to process a flat bottom or loose bale. -Processes hay into palatable rations, making your hay go further to reduce your costs. -Has tall sides to reduce spillage, ensuring your hay gets processed completely. -Offset rotor never allows the bale to be directly on top of the rotor, making slugbar adjustments possible with a bale in the chamber. -The 3-chain slatted conveyor provides needed traction to process round bales, hard or soft core, no matter what their condition. The 2650 features an inline PTO driveline for vibration free turns. The hinged PTO driveline shield allows for easy maintenance. Haybuster s rugged Transfer Case reverses rotation and speeds up the rotor to improve processing in all conditions. And of course, the 2650 gives you a rotor access door, giving you quick and easy access to the rotor for routine inspections and twine removal. The single-point and wrenchless Slugbar adjustment provides convenient slugbar setting. Now it is easy to set the slugbars to match your processing conditions. Heavy Duty Rotor and Heavy Duty Flails process both dry hay and silage bales. No special options are needed, the 2650 does it from the start.
2650 2-STAGE LOADER Loading bales is easy! Just lower the loader to the ground, and back up until the loader tines are under the bale. The two stage loader lifts each bale separately without disturbing the next bale, it also carries the second bale to increase productivity. 1 2 3 The RIGHT OPTIONS on your 2650 can make all the difference! 1. Stripper Channels: Hay too long: the cut length can be shortened by adding up to two additional Stipper Channels. 2. 2650GT 21-Bushel Grain Tank: The Haybuster Grain tank applies grain on top of the windrow at the same time as you re processing. The grain tank top dresses corn, cereal grains, and palletized feed supplements. You can easily maintain your Feed Ratio Per Animal with the Grain Tank s adjustable metering system. 3. Hydraulic Deflector Controls-Wide Deflector Belt: The Hydraulic deflector saves you steps by moving the rack and the deflector from transport position to working position without leaving the comfort of your tractor cab. The wide deflector belt discourages leaves and fines from being blown past the fence-line bunk into the feedlot. Highly recommended when bunk feeding. 4. Electronic Scale: Manage your feeding program better with a Digi-Star EZ 2000 Scale system from Haybuster. The EZ 2000 has the best features and the best functions. 5. Fenders, Road Lights, Highway or Flotation Tires: Choose the tire size that fits your needs: 12.5L x 15 8 ply implement tires, 31 x 10.5 x 15 load range C highway tires, or 14L x 16.1 8 ply flotation tires. 6. Axle Extension Kit: Extends the 2650 s axles 12 inches (30.48cm) on each side for stability in uneven and steep terrain. 4 5a 6 5b
SPECIFICATIONS WEIGHT Total - 4500 lbs (2041 kg) Tongue - (Bale loader fully raised) - 1300 lbs (589.7kg) TRANSPORT DIMENSIONS (Bale loader fully raised, deflector folded) Width - 8 ft 4 in (2.52 m) Length - 14 ft 11 in (4.55 m) Height - 11 ft (3.35 m) WORKING DIMENSIONS (With 1 bale, deflector in spread position) Width - 10 ft 10 in (3.31 m) Length - 14 ft 11 in (4.55 m) Height - 11 ft (3.35 m) (With 2 bales, deflector in spread position) Width - 10 ft 10 in (3.31 m) Length - 19 ft 7 in (5.95 m) Height - 11 ft (3.35 m) CHASSIS FEATURES Towing Arrangement - Clevis type hitch Jack Capacity - 5000 lbs (2,273 kg) Jack Travel - 10 in (25.4 cm) Tires - 2) 12.5L x 15-8 Ply Wheels - 2) 10 x 15-6 Bolt, Drop Center Bearing Type - Tapered Roller BALE LOADER Type - Integral 2 Stage, Twin Boom Arms Bale Tines - Tubular Steel, 10 Float, 4 Position Width Adjustable Hydraulic Cylinder - 4-1/2 in x 24 in (11.43 cm x 60.96 cm ) Double-Acting BALE CONVEYOR Type - 3 Roller Chains with Bolt-On Cross Slat Drive - Hydraulic Orbital Motor with Adjustable Flow Control BALE SHREDDER CHAMBER Max. Bale Size - 6 ft long x 6-1/2 ft dia (1.83 m x 1.98 m) Max. Bale Weight each - 2200 lbs (1000 kg) Rotor Length - 78 in (1.98 m) Rotor Diameter (Flails extended) - 25 in (63.5 cm) Rotor Bearing - Ball, 13 4 in (4.44 cm) Number of Flails - 30 Flail type - Heavy Duty, 7/16 in (11.11 mm) thick, 3 lbs (1.36 kg), Heat Treated Spring Steel, Swinging Number of Stripper Channels - 1 Number of Slugbars - 5 Slugbar - Single point, 5 Adjustment Settings through a 180 Range Delivery - Right Hand Discharge Deflector - 6 Adjustment Settings through a 120 Range Max. Horizontal Spread - Straw, up to 50 ft (15.24 m) OPERATOR CONTROLS Loader - 1 Tractor Double-Acting Hydraulic Valve Bale Conveyor - 1 Tractor Double-Acting Hydraulic Valve Bale Conveyor Speed - Conveyor Speed Control Valve Slugbar - Hand Lever with 5 Settings Deflector - Hand Lever with 6 Settings REQUIREMENTS FOR OPERATION PTO Horsepower Required - 65hp(48.5kw) to 155hp(115.6kw) PTO Type - 1000 RPM, 13 8 in dia PTO Shaft with 21 Splines Min. Tractor Hydraulic Output - 8 gpm at 1500psi (46 lpm x 10,345 kpa) Tractor Hydraulic Controls - 2 Double-Acting Control Valves with Quick Coupler Outlets Tractor Weight - must be of equal or greater weight than that of a 2650 with 2 bales SPECIFICATIONS [ 2 6 5 0 b a l e b u s t e r ] PO Box 1940 Jamestown, ND 58402-1940 Phone: (701) 252-4601 Fax: (701) 252-0502 Website: www.haybuster.com DuraTech Industries International, Inc. reserves the right to change its products or their specifications at anytime without notice or obligation. Illustrations, specifications, and descriptions contained herein were accurate at the time of publication, but are subject to change without notice. Illustrations may include optional equipment or accessories and may not include all standard equipment. 2650 UP 3000 2/06