Specificatio Flow Products Magetic Flowmeters MAG-X Series 10DX3111E (1/2-12 ) Flowmeter system with a remote aalog or microprocessor sigal coverter. Available i sizes 1/2 to 12 Available with ANSI or DIN flages Typical flowrate measuremet is idepedet of viscosity, desity, ad temperature Stadard NEMA 4X eclosure ratig for use i corrosive eviromets Produced i a ISO 9001 certified facility. System accuracies of ±1/2%, or 1/4% of rate depedig o the sigal coverter chose. Optioal remote commuicatios via RS- 232C, RS-485, ABB RSK or HART Protocol. Oly oe coduit required betwee primary ad secodary. MAG-X Series 10DX3111E (1/2-12 ) S-FL/MAG-10DX3111E_2 1
SERIES 3000 MAGNETIC FLOWMETER MAG-X The Series 10DX3111 Magetic Flowmeter is a pulsed DC-type volumetric, liquid flow rate detector. The coils of the magetic flowmeter are excited with pulsed DC curret i order to establish the magetic field. As a coductive liquid passes through this magetic field, a voltage is iduced i the liquid which is directly proportioal to its velocity. This iduced voltage is sesed by the electrodes ad set to the coverter which digitally processes these sigal ad coverts it ito aalog ad digital output sigals. The flowmeter primary is available i a remote cofiguratio with the 50XM1000N coverter. Egieerig Specificatios Miimum Liquid Coductivity: 5µS/cm. Vacuum Limits: Full Vacuum: For TEFLON PTFE 1/2 to 4, TEFZEL, Hard Rubber, Soft Rubber, Neopree, ad Polyurethae liers. For TEFLON PTFE 6 to 12 3.9 psia (26.9 kpaa) @ 68ºF (20ºC) 6.7 psia (46.2 kpaa)@ 266ºF (130ºC) Temperature Limits: Process: -15ºF (-26ºC) to 356ºF (180ºC) for TEFLON 1/2 to 12 Sizes. 266ºR (130ºC) for TEFZEL 190ºF (88ºC) for Neopree & Polyurethae 170ºF (77ºC) for Soft & Hard Rubber Ambiet: -15ºF (-26ºC) to 140ºF (60ºC) for all liers Eclosure Classificatio: Stadard: NEMA 4X (IP65) Optioal: Accidetal submergece (IP67) i water up to 30 feet (9 meters) deep for up to 48 hours. Optioal: Cotiuous submerge (IP68) Certificatios: FM Approved No-Icedive for CI, I, Div, 2, Groups A, B, C & D, Outdoor Hazardous Locatios, NEMA 4X, Dust-Igitioproof CI, II, Div, 1, Groups E, F, & G. Suitable for CI, III, Div. 1. With itrisically safe electrodes. FM Approved Explosioproof Class I, Div. 1, Groups B, C & D Certificatios: FM Approved No-Icedive for CI, I, Div, 2, Groups A, B, C & D, Outdoor Hazardous Locatios, NEMA 4X, Dust-Igitioproof CI, II, Div, 1, Groups E, F, & G. Suitable for CI, III, Div. 1. With itrisically safe electrodes. FM Approved Explosioproof Class I, Div. 1, Groups B, C & D Coectios: Process Flages: ANSI Class 150 or 300, DIN PN 6, 10, 16, 25 ad 40 Electrical Coectio: 1/2 NPT or PG 13.5 Vibratio Immuity: 1.5G for 10-150 Hz CAPACITY TABLE SIZE METER* CAPACITY MINIMUM RANGE MAXIMUM RANGE i. mm gpm gpm L/mi gpm L/mi 1/2 15 26.4 0.53 2 26.4 100 1 25 52.8 1.06 4 52.8 200 1.5 40 158.5 3.17 12 158 600 gpm m3/h gpm m3/h 2 50 264.1 5.28 1.2 264 60 3 80 792.5 15.9 3.6 792 180 4 100 1,056 21.1 4.8 1056 240 6 150 2,641 52.8 12 2641 600 8 200 4,755 95.1 21.6 4755 1080 10 250 7,925 159 36 7925 1800 12 300 10,567 212 48 10567 2400 *Meter Capacity = Volumetric flowrate @ 32.81 ft/sec. Note: Flow Velocity (ft/s) = Operatig GPM x 32.81/meter capacity Materials of Costructio Meter Spool: Flages: Liers: 304 Stailess Steel Carbo Steelor 304 Stailess Steel TEFLON PTFE ad TEFZEL ; Available i sizes 1/2 to 12 Neopree, Polyurethae, Soft & Hard Rubber; Available i sizes 2 to 12 Electrode Material: 316 SST, Hastelloy C, Titaium, Tatalum, Platium/ Iridium, Zircoium. Housig & Coectio Box: Cast Alumium Lier Protectors & Groudig Rigs: 316 Stailess Steel or Hastelloy S-FL/MAG-10DX3111E_2 2
Model Number Desigatio for the 10DX3111 Model Number 10DX3111 Desig Level 1/2" to 12" (w/ 50XM1000 coverter)... E Meter Lay Legth Stadard... D 10D1419 & 10D1465... E Other... Z Lier Hard Rubber... A Soft Rubber... B Polyurethae... D TEFLON PTFE... E Neopree... L TEFZEL ETFE... N Size 1/2" (15mm) Teflo/Tefzel oly... 07 1" (25mm) Teflo/Tefzel oly... 09 1.5" (40mm) Teflo/Tefzel oly... 11 2" (50mm)... 12 3" (80mm)... 14 4" (100mm)... 15 6" (150mm)... 17 8" (200mm)... 18 10" (250mm)... 19 12" (300mm)... 20 Flage Coectio DIN PN 10... C DIN PN 16... D DIN PN 25... E DIN PN 40... F ANSI 150... P ANSI 300... Q Flage Material Carbo Steel... 1 304 Stailess Steel... 2 Protector Plate (Teflo Lier Oly) Noe Required... A 316 Stailess Steel... B Hastelloy C... E Electrode Desig Flush... 2 Bullet Nose... 3 Slurry Service... 7 Electrode Material 316 Stailess Steel... B Hastelloy B... C Hastelloy C... D Titaium... E Tatalum (Teflo or Tefzel Lier Oly... F Platium/Iridium (Teflo or Tefzel Lier Oly... H Zircoium... L Certificatio Geeral Purpose... A FM Approved for Cl I, Div. 2, Group A, B, C, & D... K FM Approved for Cl I, Div. 1, Groups B, C, & D... L Eclosure Classificatio NEMA 4X, IP65, IEC 529... 1 Accidetal Submergece, IP67, IEC 529... 2 Cotiuous Submergece, IP68... 5 Process Temperature Rage TEFLON PTFE or TEFZEL <266 F (130 C)... 1 TEFLON PTFE <356 F (180 C)... 2 Soft Rubber or Hard Rubber <170 F (77 C)... 3 Neopree or Polyurethae <190 F (88 C)... 4 Lie/Excitatio Frequecy 50 Hz / 6-1/4 Hz... 1 50 Hz / 12-1/2 Hz... 2 60 Hz / 7-1/2 Hz... 3 60 Hz / 15 Hz... 4 Customer Iformatio Laguage - Eglish... 2 Remote Sigal Coverter... 1 Not available at this time S-FL/MAG-10DX3111E_2 3
Figure 1. Outlie Dimesios of Remote Mouted Sigal Coverter OUTLINE DIMENSIONS iches (mm) DIM Size 1/2 (15) 1 (25) 1-1/2 (40) 2 (50) 3 (80) 4 (100) 6 (150) 8 (200) 10 (250) 12 (300) FLANGE CLASS 150 300 150 300 150 300 150 300 150 300 150 300 150 300 150 300 150 300 150 300 MODEL NO. L 10DSX3111ED 7-7/8 9 7-7/8 9 7-7/8 9 7-7/8 9 7-7/8 9 9-7/8 11 11-13/16 13-25/32 17-23/32 19-11/16 (200) (229) (200) (229) (200) (229) (200) (229) (200) (229) (250) (280) (300) (350) (450) (500) L 10DSX3111EE 14 14 16 16 12 12 17-23/32 19-11/16 21-21/32 24-13/32 (356) (356) (406) (406) (305) (305) (450) (500) (550) (620) LINER RF 1-3/8 2 2-7/8 3-5/8 5 6-3/16 8-1/2 10-5/8 12-3/4 15 (35) (51) (73) (92) (127) (157) (216) (270) (324) (381) POLY/NEO/ 15/16 1-1/16 1-1/8 1-5/16 1-1/8 1-7/16 1-3/16 1-5/8 1-5/16 1-13/16 1-3/8 2-1/16 1-1/2 2-1/4 N/A N/A N/A RUBBER LINER (24) (27) (29) (33) (29) (36) (30) (41) (33) (46) (35) (52) (38) (57) B TEFLON LINER 11/16 13/16 27/32 31/32 29/32 1-1/32 1-3/32 1-9/32 1-3/32 1-13/32 1-1/8 1-9/16 1-9/32 1-25/32 1-3/8 2-1/16 1-1/2 2-1/4 1/2 5/8 (17) (21) (21) (25) (23) (26) (27) (32) (27) (35) (29) (40) (33) (45) (35) (52) (38) (57) TEFZEL LINER (13) (16) 5/8 3/4 3/4 7/8 27/32 31/32 3/4 1-1/4 1-3/32 1-3/8 1-1/8 1-9/16 1-1/4 1-3/4 1-5/16 2 1-25/64 2-9/64 (16) (19) (19) (22) (21) (25) (19) (32) (27) (35) (29) (40) (32) (44) (33) (51) (35) (54) d 5/8 5/8 3/4 5/8 7/8 3/4 3/4 3/4 7/8 3/4 7/8 7/8 7/8 7/8 1 1 1-1/8 1 1-1/8 (16) (16) (19) (16) (22) (19) (19) (19) (22) (19) (22) (22) (22) (22) (25) (25) (29) (25) (29) N 4 4 4 4 4 4 4 8 4 8 8 8 8 12 8 12 12 16 12 16 BC 2-3/8 2-5/8 3-1/8 3-1/2 3-7/8 4-1/2 4-3/4 5 6 6-5/8 7-1/2 7-7/8 9-1/2 10-5/8 11-3/4 13 14-1/4 15-1/4 17 17-3/4 (60) (67) (79) (89) (98) (114) (121) (127) (152) (168) (191) (200) (241) (270) (298) (330) (362) (387) (432) (451) OD 3-1/2 3-3/4 4-1/4 4-7/8 5 6-1/8 6 6-1/2 7-1/2 8-1/4 9 10 11 12-1/2 13-1/2 15 16 17-1/2 19 20-1/2 (89) (95) (108) (124) (127) (156) (152) (165) (190) (210) (229) (254) (279) (318) (343) (381) (406) (445) (483) (521) A 2-15/16 3-7/16 3-15/16 4-9/16 3-15/16 5-1/8 6-11/16 7-11/16 9-27/32 9-27/32 (75) (87) (100) (116) (100) (130) (170) (195) (250) (250) C 2-7/16 2-7/8 3-7/32 3-17/32 4-11/32 5-1/8 5-25/32 7-1/16 8-5/32 9-27/32 (62) (73) (82) (90) (110) (130) (147) (179) (207) (250) E 4-1/4 4-11/16 5-1/32 5-11/32 6-5/32 6-15/16 7-5/8 8-7/8 9-31/32 12-9/16 STANDARD (108) (119) (128) (136) (156) (176) (194) (225) (253) (319) F TEMPERATURE 5-5/16 5-3/4 6-3/32 6-13/32 7-7/32 8 8-5/8 9-7/8 11 13-23/32 (135) (146) (155) (163) (183) (203) (216) (251) (279) (348) E 4-5/8 5-1/16 5-13/32 5-23/32 6-17/32 7-5/16 12-3/8 13-5/8 14-23/32 16-13/32 HIGH (117) (128) (137) (145) (166) (186) (314) (346) (375) (417) F TEMPERATURE 5-11/16 6-1/8 6-15/32 6-25/32 7-19/32 8-3/8 13-7/16 14-11/16 15-25/32 17-15/32 (144) (156) (164) (172) (193) (213) (341) (373) (401) (444) W N/R N/R N/R N/R N/R N/R 12-3/16 14-3/8 16-25/32 20-5/64 (310) (365) (426) (510) S-FL/MAG-10DX3111E_2 4
NOTES: 1) All dimesios are i iches. Dimesios i brackets [ ] are i millimeters [mm]. 2) Dimesios are guarateed oly if this prit is certified. 3) This drawig is thrid agle projectio as show. 4) Flage bolts straddle ceterlies. 5) Flow must be i same directio as flow arrow. 6) Meter must be completely filled with liquid to isure accruacy. 7) All dimesios subject to maufacturig toleraces of ±1/8 [3]. S-FL/MAG-10DX3111E_2 5
WEIGHT TABLE METER SIZE ANSI CLASS 150 ANSI CLASS 300 i. mm lbs kg lbs kg 1/2 15 4.5 2 5.5 2.5 1 25 9 4 10 4.5 1.5 40 12 5.5 13 6 2 50 18 8 22 10 3 80 26 12 35 16 4 100 40 18 48 22 6 150 105 47 140 64 8 200 155 70 210 95 10 250 220 100 295 134 12 300 275 125 365 166 The Compay s policy is oe of cotiuous product improvemet ad the right is reserved to modify the iformatio cotaied herei without otice. 2002 ABB Ic. Prited i USA (12/17/01) ABB Ic. 125 East Couty Lie Road Warmister, PA 18974 USA Tel: 215-674-6000 Fax: 215-674-7183 ABB Ltd Howard Road, St. Neots Cambs, Eglad, PE19 3EU Tel: +44 (0)1480-475-321 Fax:+44 (0)1480-217-948 ABB S.p.A Via Sempioe 243 20016 Pero (Milao) Italy Tel: +39 (02) 33928 1 Fax: +39 (02) 33928 240 ABB GmbH Idustriestr. 28 D-65760 Eschbor Germay Tel: +49 (0) 6196 800 0 Fax: +49 (0) 6196 800 1849 S-FL/MAG-10DX3111E_2 6