2 Series Characterized Control Valve, Non-Spring ctuator Two-way Valve with Stainless Steel all and Stem, NPT Female Ends Service: Flow Characteristic: Media Temp Range: Maximum Differential: Pressure ( P) mbient Temp Range: Leakage chilled or hot water, 60% glycol -port equal percentage 0 F to 212 F [-18 C to 100 C] 20 psi for typical applications -22 F to 122 F [-0 C to 50 C] 0% for to TR LR R 2 Two-way Characterized Control Valve, Stainless Steel all and Stem Valve Non-Spring ctuator On/Off, Floating On/Off, Floating Proportional Proportional Proportional / MFT Model C v Valve Close- # Rating Nominal Size Off LR24- LR24-SR LRX24-MFT CCV DN psi TR24--T US R24- TR24-SR-T US R24-SR RX24-MFT Valve Inches mm 207 0. 1/2 15 200 Pg 88 Pg 92 Pg 90 Pg 94 Pg 104 208 0.46 1/2 15 200 Pg 88 Pg 92 Pg 90 Pg 94 Pg 104 209 0.8 1/2 15 200 Pg 88 Pg 92 Pg 90 Pg 94 Pg 104 210 1.2 1/2 15 200 Pg 88 Pg 92 Pg 90 Pg 94 Pg 104 211 1.9 1/2 15 200 Pg 88 Pg 92 Pg 90 Pg 94 Pg 104 212.0 1/2 15 200 Pg 88 Pg 92 Pg 90 Pg 94 Pg 104 21 4.7 1/2 15 200 Pg 88 Pg 92 Pg 90 Pg 94 Pg 104 214 7.4 1/2 15 200 Pg 88 Pg 92 Pg 90 Pg 94 Pg 104 215* 10 1/2 15 200 Pg 88 Pg 92 Pg 90 Pg 94 Pg 104 217 4.7 /4 20 200 Pg 88 Pg 92 Pg 90 Pg 94 Pg 104 218 7.4 /4 20 200 Pg 88 Pg 92 Pg 90 Pg 94 Pg 104 219 10 /4 20 200 Pg 88 Pg 92 Pg 90 Pg 94 Pg 104 220* 24 /4 20 200 Pg 88 Pg 92 Pg 90 Pg 94 Pg 104 222 7.4 1 25 200 Pg 92 Pg 94 Pg 104 22 10 1 25 200 Pg 92 Pg 94 Pg 104 224 19 1 25 200 Pg 92 Pg 94 Pg 104 225* 0 1 25 200 Pg 92 Pg 94 Pg 104 229 10 1-1/4 2 200 Pg 92 Pg 94 Pg 104 20* 19 1-1/4 2 200 Pg 92 Pg 94 Pg 104 21 25 1-1/4 2 200 Pg 108 Pg 106 Pg 118 22* 7 1-1/4 2 200 Pg 108 Pg 106 Pg 118 28 19 1-1/2 40 200 Pg 108 Pg 106 Pg 118 29 29 1-1/2 40 200 Pg 108 Pg 106 Pg 118 240* 7 1-1/2 40 200 Pg 108 Pg 106 Pg 118 248 29 2 50 200 Pg 108 Pg 106 Pg 118 249 46 2 50 200 Pg 108 Pg 106 Pg 118 250* 57 2 50 200 Pg 108 Pg 106 Pg 118 251 65 2 50 100 Pg 108 Pg 118 252 85 2 50 100 Pg 108 Pg 118 25 120 2 50 100 Pg 108 Pg 118 254* 240 2 50 100 Pg 108 Pg 118 261 60 2.5 65 100 Pg 108 Pg 118 262 75 2.5 65 100 Pg 108 Pg 118 26 110 2.5 65 100 Pg 108 Pg 118 264 150 2.5 65 100 Pg 108 Pg 118 265* 210 2.5 65 100 Pg 108 Pg 118 277 70 80 100 Pg 108 Pg 118 278 10 80 100 Pg 108 Pg 118 280* 170 80 100 Pg 108 Pg 118 Electrical Covered ft cable, Covered Terminal ft cable, ft cable, Connection Terminal Strip 1/2 conduit Strip 1/2 conduit 1/2 conduit fitting fitting fitting TR24--T US LR24- R24- * Models without characterizing discs. See pg 11 for corrected C v s with piping reduction factor. Options (add to above list price) TR24- US TR24-SR US LR24 LRX24 LRX24-MFT LRX24-MFT95 RX24- RX24-SR RX24-MFT RX24-MFT95 built-in aux. switch -S Pg 92, 94 -foot cable Pg 90 10-foot cable /00 Pg 88 Pg 90 Pg 96, 100. 102 Pg 104 Pg Pg Pg 112 Pg118 Pg 16-foot cable /500 Pg 88 Pg 90 Pg 96, 100. 102 Pg 104 Pg Pg Pg 112 Pg118 Pg 120 VC power supply Pg Pg 98, 102 Pg Pg 112, 114 See elimo s flexible product range on page 224 for a complete list of configurable actuators and options. Note: For TF/TR actuators, no weather shield available at this time. Call 800-54-908 TR24-SR-T US LR24-SR R24-SR LRX24-MFT RX24-MFT 14
2 Two-way Characterized Control Valve, Stainless Steel all and Stem RX24- ctuators, On/Off, Floating Point Technical Data/Submittal pplication This valve is typically used in air handling units on heating or cooling coils, and fan coil unit heating or cooling coils. Some other common applications include Unit Ventilators, VV box re-heat coils and bypass loops. This valve is suitable for use in a hydronic system with variable flow. This valve is designed to fit in compact areas where on/off or floating point control is required using 24 VC. Valve Specifications: Service chilled or hot water, 60% glycol Flow characteristic -port equal percentage ction max 90 rotation Sizes 1-1/4 to Type of end fitting female, NPT Materials: ody forged brass, nickel plated all stainless steel Stem stainless steel Seats PTFE Characterizing disc TEFZEL Packing 2 EPDM O-rings, lubricated Pressure rating 400 PSI Media temp range 0 F to 212 F Close-off pressure 200 PSI for 1-1/4 (21) to 2 (250) 100 PSI for 2 (250) to (280) Maximum differential 20 psi for typical applications pressure ( P) Leakage 0% Cv rating -port: see product chart for values Tefzel is a registered trademark of DuPont ctuator Specifications RX24- Power supply 24 VC ± 20% 50/60 Hz 24 VDC ± 10% Power consumption running: 2.5 W holding: 0.2 W Transformer sizing 5.5 V (class 2 power source) Electrical connection 18 G plenum rated cable 1/2 conduit connector ft [1m] 10 ft [m] 16 ft [5m] Overload protection electronic throughout 0 to 95 rotation Control On/Off, Floating Point Input impedance 600Ω ngle of rotation 95 Direction of rotation reversible with protected 1 0 switch Position indication handle Manual override external push button Running time 00 seconds 95 seconds 150 seconds constant independent of load Humidity 5 to 95% RH non condensing (EN 6070-1) mbient temperature -22 F to +122 F [-0 C to +50 C] Storage temperature -40 F to +176 F [-40 C to +80 C] Housing NEM 2/IP54 Housing material UL94-5V gency listings culus acc. to UL6070-1/-2-14, CN/CS E6070-1, CS C22.2 No. 24-9, CE acc. to 89/6/EEC Noise level <45d() Quality standard ISO 9001 RX24--T Electrical connection screw terminal (for 26 to 14 G wire) protected (NEM 2/IP20) Rated impulse voltage 800V, Control pollution degree, Type of action 1 (1. for -S models) 110 See Selection Chart Pg 14 for Control Valve No., C v and Close-off
2 Two-way Characterized Control Valve, Stainless Steel all and Stem RX24- ctuators, On/Off, Floating Point Technical Data/Submittal Dimensions.46" [88]." [84] 1.5" [5] 8.5" [216] 2.49" [6.4] D155 Nominal Valve Size Dimensions in Inches [mm] in mm 1-1/4 * 2 4.45 [11] 1.87 [48] 1-1/2 40 4.1 [109.5] 1.88 [47.8] 2 50 4.19 [108.4] 2.44 [62.0] 2 ** 50 5.00 [124] 2.78 [69.45] 2.5 65 5.4 [18] 2.78 [69.45] 80 5.71 [145] 2.78 [69.45] * On model numbers 21 and 22, the 1-1/4 valve has the same dimensions as a 1-1/2 valve. These are 1-1/2 valve bodies with 1-1/4 NPT Threads. pplies to 248-250 ** pplies to 251-254 Flow Pattern Wiring Diagrams Flow Direction CUTION 2 Equipment damage! ctuators may be connected in parallel. Power consumption must be observed and input impedance must be observed. Characterizing Disc (Where applicable) Two-way E L I M O INSTLLTION NOTES ctuators may also be powered by 24 VDC. PPLICTION NOTES Meets culus or UL and CS requirements without the need of an electrical ground connection. WRNING Live Electrical Components! During installation, testing, servicing and troubleshooting of this product, it maybe necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. W412 WRNING Live Electrical Components! During installation, testing, servicing and troubleshooting of this product, it maybe necessary to work with live electrical components. Have a qualified licensed electrician or other individual who has been properly trained in handling live electrical components perform these tasks. Failure to follow all electrical safety precautions when exposed to live electrical components could result in death or serious injury. W41 On/Off Line Volts 24 VC Transformer a open a closed The indication of direction is valid for switch position 1. a lk (1) Common Wht (2) + Wht () + 1 0 RX24- Line Volts 24 VC Transformer The indication of direction is valid for switch position 1. Floating Point or On/Off control lk (1) Common Wht (2) + Wht () + 1 0 RX24-111
Electronic Characterized Control Valves 2/ Series Characterized Control Valves Default Set-Up: Two-way Valve Two-way Valve Three-way Valve Three-way Valve (Specify upon ordering) (Specify upon ordering) (Specify upon ordering) (Specify upon ordering) Non-Spring - Stays in Last Position TR24--T US Power to pin 2 will Power to pin 2 will drive valve CCW. drive valve CCW. Power to pin will Power to pin will drive valve CW. drive valve CW. TR24-SR-T US NC: Closed to, will NO: Open to, will close NC: Closed to, will NO: Open to, will close open as voltage increases. as voltage increases. open as voltage increases. as voltage increases. (Can be chosen with (Can be chosen with switch inside terminal switch inside terminal block of actuator). block of actuator). LR24-, LR24-MFT Power to pin 2 will drive valve NO: Open to, will close Power to pin 2 will drive valve NO: Open to, will close LR24-SR, CW. Power to pin will drive as voltage increases or power CW. Power to pin will drive as voltage increases or power LRX24-MFT, valve CCW. The above will applied. (Can be chosen valve CCW. The above will applied. (Can be chosen R24-, R24-SR function when the directional with CW/CCW switch ). function when the directional with CW/CCW switch ). R24-MFT switch is in the 1 position, to switch is in the 1 position, to reverse select the 0 position. reverse select the 0 position. TFX24 US NO/FO Valve: Open to NC/FC Valve: Closed to NO/FO Valve: Open to NC/FC Valve: Closed to LF24 US will drive closed. will drive open. will drive closed. will drive open. F24 US Spring ction: Will spring Spring ction: Will spring Spring ction: Will spring Spring ction: Will spring open to closed to open to closed to Spring - Note Fail Position TF (-), MFT, SR NC/FO Valve: Closed to NC/FC or NO/FC NC/FO Valve: Closed to NC/FC or NO/FC LF (-), MFT, SR will drive open. Valve: Closed to or will drive open Valve: Closed to F, MFT, SR Spring ction: Will spring Open to Spring ction: Will spring or Open to Floating or proportional open to (Can be chosen with open to (Can be chosen with type actuators CW/CCW switch). CW/CCW switch). Spring ction: Will spring Spring ction: Will spring closed to closed to NO/FO Valve: Open to Spring ction: Will spring open to (NO action can be chosen with CW/CCW switch). NO/FO Valve: Open to Spring ction: Will spring open to (NO action can be chosen with CW/CCW switch). General Wiring Instructions WRNING The wiring technician must be trained and experienced with electronic circuits. Disconnect power supply before attempting any wiring connections or changes. Make all connections in accordance with wiring diagrams and follow all applicable local and national codes. Provide disconnect and overload protection as required. Use copper, twisted pair, conductors only. If using electrical conduit, the attachment to the actuator must be made with flexible conduit. lways read the controller manufacturer's installation literature carefully before making any connections. Follow all instructions in this literature. If you have any questions, contact the controller manufacturer and/or elimo. Transformer(s) elimo actuators require a 24 VC class 2 transformer and draws a maximum of 10 V per actuator. The actuator enclosure cannot be opened in the field, there are no parts or components to be replaced or repaired. EMC directive: 89/6/EEC Software class : Mode of operation type 1 Low voltage directive: 7/2/EEC CUTION: It is good practice to power electronic or digital controllers from a separate power transformer than that used for actuators or other end devices. The power supply design in our actuators and other end devices use half wave rectification. Some controllers use full wave rectification. When these two different types of power supplies are connected to the same power transformer and the DC commons are connected together, a short circuit is created across one of the diodes in the full wave power supply, damaging the controller. Only use a single power transformer to power the controller and actuator if you know the controller power supply uses half wave rectification. 217
Electronic Characterized Control Valves 2/ Series Characterized Control Valves Operation/Installation Correct Piping: 2-way valves should be installed with the disc upstream. If installed with disc downstream, flow curve will be deeper. If installed backwards it is NOT necessary to remove and change. No damage or control problems will occur. Two-Way Valve Piping Diagram (1 Input, 1 Output) Three-Way Mixing Valve Piping Diagram (2 Inputs, 1 Output) Three-Way Diverting Valve Piping Diagram (1 Input, 2 Outputs) -way valves must be piped correctly. They can be mixing or diverting. Mixing is the preferred piping arrangement. The ELIMO Characterized Control Valve is a CONTROL valve, not a manual valve adapted for actuation. The control port is the port. It is similar to the globe valve in that the middle port is the or bypass port. The common port is on the main opposite the port. These diagrams are for typical applications only. Consult engineering specification and drawings for particular circumstances. The port must be piped to the coil to maintain proper control. The port restricts flow by 0% of port value. Incorrect Piping: Three-Way Mixing Valve Piping Diagram (2 Inputs, 1 Output) Three-Way Diverting Valve Piping Diagram (1 Input, 2 Outputs) WRNING! Do Not Pipe in this manner! Note Valve Porting! The port must be piped to the coil! Not the port! Flow is not possible from to. If port is not piped as the common port, the valve must be re-piped. It is good practice to install a balancing valve in the bypass line. These valves are intended for closed loop systems. Do not install in an open loop system or in an application that is open to atmospheric pressure. ssembly: 1 1 2 One screw attaches actuator to valve Four actuator mounting positions 2-way flow pattern 4 5 -way flow pattern (mixing shown) Top of valve stem indicates direction of flow (Flow to shown) Note: For diverting flow, flow enters in and diverts to and ports. 5 CCW 4 x 90 2 -=0% 4 -=100% 218
2-FRONT Characterized Control Valves (CCV) Flow Pattern Two-way Characterized Control Valves (elimo 2 Series) (elimo 6 Series) Flow Direction Characterizing Disc (Where applicable) Two-way *Two-way valves should be installed with the disc upstream. E L I M O Three-way Characterized Control Valves (elimo Series) Three-way Mixing *The port must be piped to the coil to maintain proper control. Three-way Diverting Characterizing Disc (where applicable) YPSS Port Disc (ll -way models) Characterizing Disc (where applicable) Port Disc (ll -way models) Port must be piped to the by-pass line. Mounting: The valves can be mounted in any position, except stem below horizontal. 60 D164 85 85 219