5776 (supersedes 576)-06-U Technical Data Specifications & Capacities HSL Crawler Crane 50 Ton (6.80 metric ton) CAUTION: This material is supplied for reference use only. Operator must refer to in-cab Crane Rating Manual and Operator's Manual to determine allowable crane lifting capacities and assembly and operating procedures.
5776 (supersedes 576)-06-U
5776 (supersedes 576)-06-U Table Of Contents Upper Structure............................................................................ Frame.................................................................................... Engine................................................................................... Hydraulic System.......................................................................... Load Hoist Drums......................................................................... Optional Front-Mounted Third Hoist Drum................................................... Boom Hoist Drum.......................................................................... Boom Hoist System........................................................................ Swing System............................................................................. Counterweight............................................................................ Operator Cab............................................................................. Rated Capacity Limiter System.............................................................. Machinery Cab............................................................................ Catwalks................................................................................. Lower Structure............................................................................ Carbody.................................................................................. Side Frames.............................................................................. Travel and Steering........................................................................ Jack System.............................................................................. Attachment and Options.................................................................... Conventional Tube Boom................................................................... Tube Jib.................................................................................. Auxiliary Tip Extension...................................................................... Dimensions................................................................................ Base Crane............................................................................... Side Frames.............................................................................. Upper Counterweights..................................................................... Lower Counterweights..................................................................... Boom/Luffing Boom........................................................................ Jib/Luffing Fixed Jib........................................................................ Luffing Jib Extensions...................................................................... Hook Balls................................................................................ Hook Blocks.............................................................................. Assembly Diagram......................................................................... Working Weights........................................................................... Transport Weights.......................................................................... Transport Drawings........................................................................ Load Hoist Performance.................................................................... Working Areas............................................................................. Attachments............................................................................... Main Boom Make-up...................................................................... Main Boom Working Range Diagram........................................................ Main Boom Load Chart..................................................................... 4 6 6 7 7 8 0 5 5 6 7 0 4 5
5776 (supersedes 576)-06-U Jib Attachment Make-up................................................................... Jib Attachment Working Range Diagram..................................................... Jib Attachment Load Charts................................................................. Luffing Attachment......................................................................... Luffing Boom Make-up.................................................................... Luffing Jib Make-up....................................................................... 7 8 9
5776 (supersedes 576)-06-U Upper Structure Hydraulic System Frame All welded steel frame with precision machined surfaces for mating parts. Emissions Compliance Level: Tier 4f/ Stage IV() Tier / Stage IIIA() Numbers of Cylinders 6 6 Cycle 4 4 Bore & Stroke: inch (mm) 4.49 x 5.69 (4 x 45) 4.49 x 5.69 (4 x 45) Piston Displacement: in (L) 54 (8.90) 54 (8.90) Hydraulic Pumps The pump arrangement is designed to provide hydraulically powered functions allowing positive, precise control with in dependent or simultaneous operation of all crane functions. S Two variable displacement pumps operating at 4,55 psi (0kg/cm) and 74 gal/min (80L/min) powers load hoist drums, boom hoist drum, optional third drum, self assembly cylinder, and travel. S One variable displacement pump operating at 4,6 psi (5kg/cm) and 4. gal/min (60L/min) powers the swing motors, live mast flip, and counterweight removal. S One fixed displacement gear type pump operating at,987 psi (0kg/cm) and 5.8 gal/min (59.8L/min) powers the lower jacks, counterweight pinning, side frame pinning, and hoist brake cooling (optional). S One fixed displacement gear type pump operating at,47 psi (00kg/cm) and.7 gal/min (44L/min) powers the oil cooler fan. Max. Brake Horsepower: hp (kw) 0 (9) @,800 rpm 5 (4) @,800 rpm Hydraulic Reservoir 9 gal (450L), equipped with sight level gauge. Diffusers built in for deaeriation. Peak Torque: ft lb (Nm),050 ( 44) @,500 rpm,050 ( 44) @,500 rpm / / 60 60 4 (.7) 4 (.7) Turntable Bearing S Inner race with internal swing gear is bolted to lower frame. S Outer race is bolted to upper frame. Engine Engine Full pressure lubrication, oil filter, air cleaner, hour meter, throttle, and electric control shutdown. Specification Electric/starting systems: volts Alternator: amps Crankcase Capacity: qt (L) S S S S S Cummins QSL9 Water/fuel separator w/ heater and water in fuel (WIF) sensor 0-volt block heater Grid heater - 00 amp () Can only be sold and/or operated where Tier 4f and Stage IV off-high way emission standards are accepted. () Can only be sold and/or operated where Tier and Stage IIIA off-high way emission standards are accepted. Filtration Ten micron, full flow, line filter in the control circuit. All oil is filtered prior to entering the reservoir. Counterbalance Valves All hoist motors are equipped with coun terbalance valves to provide positive load lowering and prevent accidental load drop if the hydraulic pressure is suddenly lost. Load Hoist Drums Each drum contains an axial piston, vari able speed hydraulic motor with individu al automatic winch motor brakes. S Power up/down operation modes S Optional wet-type free-fall brake sys tem S Automatic brake mode (spring applied, hydraulically released, wet type brake) S Drum lagging grooved for wire rope S Drum pawl controlled manually S Electronic drum rotation indicators S Mounted on anti-friction bearings S 4.57 in (0.6m) root diameter S 4.4 in (.05m) flange diameter S 5.0 in (0.90m) width The optional free-fall operation mode is designed to prevent load lowering even if the free-fall switch is accidentally acti vated. The automatic brake mode meets all OSHA requirements for personnel han dling. Optional Front-Mounted Third Hoist Drum The hydraulic winch is mounted in the boom base section and is used in con junction with a fleeting sheave and three sheave assembly to run the wire rope over the boom top section. S Power up/down operation mode S Automatic brake mode (spring applied, hydraulically released) S Smooth drum S Electronic drum rotation indicator S Mounted on anti-friction bearings Fuel Tank Equipped with fuel sight level gauges, flame arrester, and self-closing cap with locking eye for padlock.
5776 (supersedes 576)-06-U Boom Hoist Drum Contains a pilot controlled, bi-directional, axial piston motor and a planetary gear re duction unit to provide positive control un der all load conditions. S Spring applied, hydraulically released, disc type brake controlled automatically S Drum pawl controlled automatically S Mounted on anti-friction bearings S 6.0 in (0.66m) root diameter S 8.58 in (0.98m) flange diameter S 0.7 in (0.6m) width Boom Hoist System Designed to lift off maximum boom or maximum boom plus jib and maximum luffing attachment unassisted. Operates up to a maximum boom angle of 8. Boom hoist limit system limits maximum boom angle operation. S 0-part reeving with mm wire rope S Bridle assembly S 5 ft (7.6m) Live mast S Hydraulic tubular boom backstops S Sheaves contain sealed anti-friction bearings S Boom speed from 0-70 is 69 sec onds with no load. Speed was deter mined using 00 ft (0.48m) of tube boom. Swing System Pilot controlled bi-directional axial piston motors and planetary gear reduction units to provide positive control under all load conditions. S Spring applied, hydraulically released, 60 multi-plate brake S Free swing mode when lever is in neu tral position S Four position positive house lock S Two-speed swing S Audio/Visual swing alarm S Maximum swing speed is.7 rpm Counterweight Consists of an eleven-piece design that can be easily lowered to the ground using the removal cylinders. S ABCDE total upper counterweight is 60,000 lb (7 576kg) S Two carbody counterweights - 0,000 lb ( 608kg) each Total combined counterweight, ABCDE plus carbody counterweights is 0,000 lb (99 79kg). Operator Cab Fully enclosed modular steel compart ment is independently mounted and padded to protect against vibration and noise. S All tinted/tempered safety glass S Folding hinge entry door and sliding front glass window S 9,000 BTU hot water heater S 8,600 BTU air conditioner S Door and window locks S Circulating fan S Sun visor S Cloth seat S Defroster S Windshield wipers and washer S Dry chemical fire extinguisher S Engine instrumentation panel (voltmeter, engine oil pressure, engine water tem perature, fuel level, hydraulic oil tem perature, hour meter, and service moni tor system) S Electronic drum rotation indicators for front and rear hoist drums S Six way adjustable seat S Hand and foot throttle S Fully adjustable single axis controls S Swing lever with swing brake and horn located on handle S Bubble type level S Ergonomic gauge layout S Controls shut off lever S Control stand is adjustable for operator comfort. Rated Capacity Limiter System The HSL rated capacity limiter system is a boom hoist load cell system. This system provides the operator with useful geometri cal data, to include: S Main Boom Length S Main Boom Angle S Jib Length S Jib Angle S Operating Mode S Load Radius S Boom Tip Height S Audible Alarm S Pre-Warning Light S Overload Light S Load On Hook S Function kick-outs including over load S Operator settable stops (ramped stops) S Anti-Two Block Indicator S Boom hoist dead end load cell (no lineriders) Machinery Cab Hinged doors (three on right side, four on left side) for machinery access. Equipped with rooftop access ladder and skid resist ant finish on roof. Catwalks Standard on right and left sides. Catwalks are removable for reduced travel width.
5776 (supersedes 576)-06-U Lower Structure Carbody Lower Frame All welded construction frame with preci sion machined surfaces for turntable bearing and rotating joint. S 9 ft 0 in (.00m) overall length S 4 ft 9 in (4.48m) overall width Side Frames Side Frames All welded, precision machined, hook and pinned, steel frames. S 9 ft in (5.87m) gauge S 7 ft 9 in (8.46m) overall length S 48 in (.m) wide track shoes S Sealed (oil filled) drive planetaries S Compact travel drives S Automatic hydraulic track adjustment system - optional Track Rollers S Eleven sealed (oil filled) track rollers per side frame S Heat treated, mounted on oil filled antifriction bearings Tracks Heat treated, self-cleaning, multiple hinged track shoes joined by one-piece full floating pins; 55 shoes per side frame Take Up Idlers Cast steel, heat treated, self-cleaning, mounted on aluminum/bronze bushings. Lubricated through idler shaft. S Track Tension Adjustment - Idler wheel adjusted by means of hydraulic cylinder and hand pump. Idler wheel shaft held in position with shims after adjustment is made. Travel and Steering Travel and Steering Each side frame contains a pilot con trolled, bi-directional, axial piston motor and a planetary gear reduction unit to pro vide positive control under all load condi tions. S Individual control provides smooth, precise maneuverability including full counter-rotation. S Spring applied, hydraulically released disc type brake controlled automatically S Maximum travel speed is 0.75 mph (.km/h). S Designed to 0% gradeability Jack System System contains four hydraulic cylinders individually pinned on swing out beams. S Individual controls are mounted on car body. S Minimum height of carbody when rest ing on pontoons is 7.4 in (0.44m). S Maximum height of carbody when rest ing on pontoons is 45 in (.4m). Attachment and Options Conventional Tube Boom 60-90 ft (8.9-88.9m) Basic Boom 60 ft (8.9m) two-piece design that utilizes a 0 ft (9.4m) base section and a 0 ft (9.4m) top section with in-line connecting pins on 80 in (.0m) wide and 68 in (.7m) deep centers. S Boom foot on 5.7 in (.5m) centers S Lugs on base section for self assembly S Self assembly cylinder S Idler sheave assembly on top section S Permanent skid pads mounted on top section to protect head machinery S Six, in, (0.58m) root diameter poly mide sheaves mounted on sealed anti-friction bearings S Tip extension, fixed jib and luffing jib connecting lugs on top section S Mechanical boom angle indicator Tube Boom Extensions The following table provides the lengths available and the suggested quantity to obtain maximum boom in 0 ft (.05m) in crements. Midpoint pendant connections are required at 40 ft (4.67m) for boom lengths of 50 ft (76.0m) and greater. Tube Boom Extensions Quantity For Max Boom ft m 0.05 0 6.0 0 9.4 40.9 S Polyamide wear blocks on top of each extension S Maximum tip height of 94 ft 9. in (89.85m) S Boom connecting pins storage on each extension Tube Jib 0-90 ft (9.4-7.4m) Basic Tube Jib 0 ft (9.4m) two-piece design that uti lizes a 5 ft (4.57m) base section and a 5 ft (4.57m) top section with in-line connecting pins on 0 in (0.76m) wide and 6 in (0.9m) deep centers. S.5 in (5.7cm) diameter chords S One in (5.4m) root diameter steel sheave mounted on sealed anti-fric tion bearings S 0 ft (.0m) jib extension. S 0 ft (6.0m) jib extensions provide jib lengths of 0 ft (9.4m), 50 ft (5.4m), 70 ft (.4m), and 90 ft (7.4m). S Jib offset angles at 0, 0, and 0 S The maximum tip height of boom + jib [50 ft + 90 ft (76. + 7.4m)] is 4ft. in (04.m). Auxiliary Tip Extension Designed to use in place of jib to provide clearance between working hoist lines. The extension is equipped with one nylon in (0.58m) root diameter sheaves mounted on sealed anti-friction bear ings. Maximum capacity is 5 Ton (.68mt).
4 5776 (supersedes 576)-06-U Dimensions General Dimensions English Metric 60 ft 8.9m Minimum Load Radius.8 ft.90m Maximum Boom Angle 84 84 Track Shoe Width 48 in.m Basic Boom 5' (7.6m) @ 84 Boom Angle 4' 4 (4.7m) 8' (.46m) 5'.5 (.56m) 4' 5.5 (.6m) 4' (7.m) ' 4.7 (.78m) C L Of Rotation 7' 9 (8.46m)
5 5776 (supersedes 576)-06-U 5' 5 (4.70m) 5' (4.65m) 9' 5 (5.9m) 48 (.m) 5'.5 (7.7m) ' (7.09m) 5' 5 (4.70m) 0' 6 (.0m) 57.5 (.45m) 6.75 (0.4m) 7.8 (0.45m) 9' (5.87m)
6 5776 (supersedes 576)-06-U Base Crane Base Crane Ê Width 0 ft.5 in (.0m) Height* 45 in (.4m) Weight 89,440 lb (40 569kg) * Maximum ground clearance on pontoons H* W Side Frames Side Frames Ë W Standard 48 (.m) Shoes Length 7 ft 9 in (8.46m) Width 48 in (.m) Height 57.5 in (.45m) Weight 4,490 lb (8 80kg) Optional 60 (.5m) Shoes Length 7 ft 9 in Width 60 in Height 57.5 in Weight 4, lb (8.46m) (.5m) (.45m) (9 60kg) L H Number inside black circle Ê = # of components
7 5776 (supersedes 576)-06-U Upper Counterweights A Base Counterweight Length Width Height Weight 6 ft.50 in 5 ft 5 in 7 ft.75 in 6,000 lb Ê (.89m) (4.70m) (.0m) (6 0kg) H L A, B, C, D, & E, Wing Counterweights Length Length Width Width Height Weight: Left Side Right Side 60 in 6 in 74.5 in 7 in.50 in (.5m) (.55m) (.89m) (.80m) (0.60m),800 lb,000 lb (5 806kg) (5 44kg) H L Length Width Height Weight ft 5.75 in 4.5 in 5.5 in 0,000 lb L Î W Lower Counterweights Carbody Counterweights W W L Ë (.80m) (.0m) (0.90m) ( 608kg) W H Number inside black circle Ê = # of components
8 5776 (supersedes 576)-06-U Boom/Luffing Boom 0 ft (9.4m) Boom Top Section Length Width Deep Height Weight ft 0.9 in 85.5 in 68 in 08 in 9,699 lb L Ê (9.78m) (.7m) (.7m) (.74m) (4 99kg) W D H 0 ft (9.4m) Boom Base Section Length Width Deep Height Weight 4 ft in 86.6 in 68 in 8. in 8,4 lb L Ê (0.9m) (.m) (.7m) (.09m) ( 78kg) W H D Number inside black circle Ê = # of components
9 5776 (supersedes 576)-06-U 68 in (.7m) x 80 in (.0m) Boom/Luffing Boom Extensions 0 ft (.05m) Extension Weight :,6 lb (70kg) Weight includes pins and pendants. 86.6 (.0m) 74.50 (.89m) 86.6 (.0m) 0 ft (6.0m) Extension Weight :,646 lb ( 06kg) Weight includes pins and pendants. 0' 5.5 (.9m) 0' 5.5 (6.4m) 74.50 (.89m) 86.6 (.0m) 0' 5.5 (9.8m) 0 ft (9.4m) Extension Weight :,70 lb ( 69kg) Weight includes pins and pendants. 74.50 (.89m) 86.6 (.0m) 40' 5.5 (.m) 40 ft (.9m) Extension Weight : 4,84 lb ( 9kg) Weight includes pins and pendants. 74.50 (.89m) 86.6 (.0m) 0 ft (6.0m) HD Extension Weight :,06 lb ( 77kg) Weight includes pins and pendants. 0' 5.5 (6.4m) 80.88 (.05m) 86.6 (.0m) 0' 5.5 (9.8m) 0 ft (9.4m) HD Extension Weight : 4,06 lb ( 95kg) Weight includes pins and pendants. 80.88 (.05m) Number inside black circle Ê = # of components
0 5776 (supersedes 576)-06-U Jib/Luffing Fixed Jib 5 ft (4.57m) Jib Top Section* L Ê W Length 6 ft 7 in (5.05m) Width 57.8 in (.47m) Height 5.6 in (0.9m) Weight 88 lb (76kg) Weight includes hardware. H 5 ft (4.57m) Jib Base & Strut Section* L Ê Length 8 ft.7 in (5.56m) Width 8. in (0.97m) Height.66 in (0.8m) Height 6. in (.55m) Weight,88lb ( 08kg) Weight includes pins, basic frontstay & backstay pendants, and hardware. W H H 0 ft (.05m) Jib Extension* Length 0 ft in (.m) Width 8 in (0.97m) Height 4.50 in (0.88m) Weight 6 lb (65kg) Weights includes pins, pendants, and hardware. 0 ft (6.0m) Jib Extension* W Ê L H W Ê Length 0 ft in (6.7m) Width 8 in (0.97m) Height 4.50 in (0.88m) Weight 59 lb (69kg) Weights includes pins, pendants, and hardware. L H Number inside black circle Ê = # of components * - Optional equipment
5776 (supersedes 576)-06-U Auxiliary Tip Extension* Length Width Height Weight 8. in 48.5 in 56.45 in 96 lb Ê (.m) (.m) (.4m) (46kg) H W L L Luffing Jib Transport Configuration* Ê Length 7 ft. in (8.6m) Width 64.9 in (.65m) Height 69. in (.76m) Height 06.5 in (.7m) Weight 0,047 lb (4 7kg) Weight includes pins, basic frontstay & backstay pendants, and hardware. W H H 0 ft (6.0m) Luffing Jib Top Section* L Ê Length ft in (6.7m) Width 6. in (.6m) Height 57.06 in (4.76m) Weight,98 lb (899kg) Weight includes pendants and hardware. W H Number inside black circle Ê = # of components * - Optional equipment
5776 (supersedes 576)-06-U Luffing Jib Extensions 60 in (.5m) x 50 in (.7m) Extensions With Pendants 64.88 (.65m) 0 ft (.05m) Extension Weight: 858 lb (89kg) 0' 4 (.5m) 55 (.40m) 64.88 (.65m) 0 ft (6.0m) Extension Weight:,76 lb (64kg) 0' 4 (6.0m) 55 (.40m) 64.88 (.65m) 0' 4 (9.5m) 0 ft (9.4m) Extension Weight:,895 lb (860kg) 55 (.40m) 64.88 (.65m) 40' 4 (.9m) 40 ft (.9m) Extension Weight:,409 lb ( 09kg) 55 (.40m) Number inside black circle Ê = # of components * - Optional equipment
5776 (supersedes 576)-06-U W Hook Balls 0 Ton (8.mt) Swivel Hook Ball* Width Height Weight.75 in 4.75 in,55 lb Ê H (0.55m) (.06m) (569kg) W 0 Ton (8.mt) Non-Swivel Hook Ball* Ê Width Height Weight.75 in 9 in, lb (0.55m) (0.99m) (549kg) H Hook Blocks 40 Ton (6.mt) -Sheave Hook Block* Width Width Width Height Weight.69 in 4.9 in.0 in 7.6 in,74 lb W W Ê (0.8m) (0.6m) (0.0m) (.84m) ( 0kg) H W W W 90 Ton (40.8mt) -Sheave Hook Block* Width Width Width Height Weight.69 in 9.75 in 7.0 in 8.06 in,6 lb Ê (0.8m) (0.50m) (0.4m) (.08m) ( 0kg) H W Number inside black circle Ê = # of components * - Optional equipment
4 5776 (supersedes 576)-06-U 65 Ton (50mt) 5-Sheave Hook Block* Width Width Width Height Weight.69 in 6.06 in. in 85.44 in 4,54 lb Ê W W (0.8m) (0.66m) (0.54m) (.7m) ( 060kg) H W W 00 Ton (8.4mt) 5-Sheave Hook Block* Width Width Width Height Weight.69 in. in.9 in 89.75 in 4,645 lb W Ê (0.8m) (0.56m) (0.6m) (.8m) ( 07kg) H W W 50 Ton (6.8mt) 6-Sheave Hook Block* Width Width Width Height Weight.69 in 5.06 in 6.8 in 94.6 in 5,660 lb W Ê (0.8m) (0.64m) (0.68m) (.9m) ( 567kg) H W Number inside black circle Ê = # of components * - Optional equipment
5 5776 (supersedes 576)-06-U Assembly Diagram Working Weights Ctwt AB+A Ctwt ABC+A Ctwt ABCDE + A lb (kg) lb (kg) lb (kg) 4,8 (55 9) 66,98 (66 440) 46,58 (88 98) psi 0.7.4.0 kg/cm 0.75 0.8 0.9 Based on basic crane including Cummins QSL9 diesel engine, turntable bearing, live mast, part boom hoist reeving, backstops, counterweight, crawler lower with 48 in (.m) wide track shoes, sealed track rollers, and catwalks, plus the following: Lifting crane - includes 60 ft (8.9m) basic boom, self assembly cylinder,,50 ft (4.48m) of type ZB main hoist rope, 975 ft (97.8m) of type ZB auxiliary hoist rope, 50 ton (6.8mt) hook block, and basic pendants. Ground Bearing Pressure
6 5776 (supersedes 576)-06-U Transport Weights Item Description Gross Weight Transport Loads lb (kg) # Base crane 89,440 40 569 Add Side Frame w/ 48 (.m) Shoes - Two required 4,490 8 80 Add Base Ctwt 6,000 6 0 Add Ctwt Biscuit (Left) - Five required,800 Add Ctwt Biscuit (Right) - Five required #6 #7 #8 #9 5 806,000 5 44 Add Lower Ctwt - Two Required 0,000 608 Add 0 ft (9.4m) Base Section w/ Backstops & Boom Foot Pins 8,4 78 Add 0 ft (.05m) Extension w/ Pendants - Two Required,6 70 Add 0 ft (6.0m) Extension w/ Pendants,646 00 Add 0 ft (9.4m) Extension w/ Pendants - One required,70 69 Add 40 ft (.9m) Extension w/ Pendants - Three required 4,84 9 Add 0 ft (6.0m) Extension w/ Pendants - Three required,06 77 Add 0 ft (9.4m) Extension w/ Pendants - Three required 4,06 95 Add 0 ft (9.4m) Top Section 9,699 4 99 Add 5 ft (4.58m) Jib Base & Strut,88 08 Add 0 ft (6.0m) Jib Extension w/ Pendants & Pins - Three required 59 68 Add 5 ft (4.6m) Jib Peak Section 88 75 Add 50 Ton (6.80mt) Hook Block 5,660 568 Add 0 Ton (8.4mt) Hook Ball w/o Swivel,4 550 Approximate Total Shipping Weight # # #4 #5 #0 # # lb 89,440 4,490 4,490 6,445 4,84,4 4,7 4,44 4,76 9,709 5,49 4,647 kg 40 569 49 08 8 80 8 80 6 5 5 69 5 0 8 767 9 48 9 48 8 0
7 5776 (supersedes 576)-06-U Transport Drawings ' (.4m) ' 6 (4.m) 7' 4 (.4m) 7' 4 (.4m) 0' (.m) LOAD # - 89,440 lb (40 569kg) Base crane 8' (.49m) LOAD # - 4,490 lb (8 80kg) Side frame w/ 48 (.m) shoes 8' (.49m) LOAD # - 4,490 lb (8 80kg) Side frame w/ 48 (.m) shoes ' (.7m) 6 (0.9m) LOAD #4-6,445 lb (6 5kg) Lower counterweight, 40 ft (.9m) boom extension, and 0 ft (.05m) boom extension
8 5776 (supersedes 576)-06-U ' (.7m) LOAD #5-4,84 lb (5 800kg) Lower counterweight and 40 ft (.9m) boom extension ' (.68m) LOAD #6 -,4 lb (4 670kg) 0 ft (9.4m) base section with backstops and boom foot pins, one,800 lb (5 806kg) counterweight, and one,000 lb (5 44kg) counterweight ' 8 (.86m) LOAD #7-4,997 lb (9 50kg) 0 ft (9.4m) top section, one,800 lb (5 806kg) counterweight, one,000 lb (5 44kg) counterweight, 0 ton (8.4mt) hook ball, and 50 ton (6.80mt) hook block ' (.7m) LOAD #8-4,4 lb (9 6kg) Two,800 lb (5 806kg) counterweights, one,000 lb (5 44kg) counterweight, and 40 ft (.9m) boom extension
9 5776 (supersedes 576)-06-U ' (.7m) ' 0 (0.9m) LOAD #9-44,776 lb (0 0kg) One,800 lb (5 806kg) counterweight, two,000 lb (5 44kg) counterweights, 0 ft (6.0m) boom extension, and 0 ft (9.4m) boom extension ' (.4m) LOAD #0-9,797 lb (8 05kg) 6,000 lb (6 0kg) base counterweight, 0 ft (6.0m) jib extension, 5 ft (4.57m) jib base and strut, and 5 ft (4.57m) jib peak 0' 6 (.m) ' (0.66m) LOAD # - 5,49 lb ( 49kg) 0 ft (9.4m) boom extension and two 0 ft (6.0m) jib extensions 0' 6 (.m) LOAD # - 4,647 lb ( 08kg) 0 ft (9.4m) boom extension and one 0 ft (4.57m) boom extension
0 5776 (supersedes 576)-06-U Load Hoist Performance Front & Rear Drums - 8mm Wire Rope Wire Rope Layer Maximum Line Pull No Load Line Speed Full Load Line Speed Pitch Diameter Layer Total lb kg ft/min m/min ft/min m/min in mm ft m ft m 5,06 4 79 7.6.6 0. 6.6 4.6 64.0 9.9 58.8 9.9 58.8 49,5 46 40.0. 7.6 66. 6.4 67.7 07.8 6. 400.6. 46,4 0 975 49.5 0.9.0 7.0 8. 79..4 67.8 6. 89.9 4 4,68 9 67 458.0 9.6 48.5 75.7 0. 767.0 7. 7. 860. 6. 5 40,8 8 5 486.5 48. 6.9 80.4. 84.6 5.9 76.8,. 9.0 6 8,574 7 497 54.9 56.9 79. 85..9 86. 66.6 8.,78.8 40. 7 6,554 6 580 54.4 65.6 94.8 89.8 5.8 90.0 8.4 85.8,660. 506.0 Boom Hoist Drums - mm Wire Rope Wire Rope Layer Maximum Line Pull No Load Line Speed Full Load Line Speed Pitch Diameter Layer Total lb kg ft/min m/min ft/min m/min in mm ft m ft m 00,940 45 785 07..7 54.6 6.6 6. 66.0 50. 45.8 50. 45.8 94,55 4 887 4.5 4.9 58. 7.8 7.6 70. 59.0 48.5 09. 94. 88,9 40 4.8 7. 6.9 8.9 9. 79. 67.7 5. 477.0 45.4 4 8,97 8 068 9.0 9. 65.6 0.0 0.6 777.4 76. 5.7 65. 99. 5 79,46 6 04 6. 4.5 69... 85.6 85.0 56.4 88. 55.5 6 75,449 4 4.5 4.8 7.0..6 85.7 9.6 59.0,0.8 4.5 7 7,8 578 50.8 46.0 76.7.4 5. 89.9 0. 6.6,4.0 76. Third Hoist Drum -.0 in (5.4mm) Wire Rope Maximum Line Pull No Load Line Speed Full Load Line Speed Pitch Diameter Layer Total Wire Rope Layer lb kg ft/min m/min ft/min m/min in mm ft m ft m 9,090 95 7 8.6 0 70. 5.4 9.9 9.9 6,560 048 97 90.5 5 76.5 584. 4 4.6 74 8.5 4,440 086 98. 7 8. 5 65.0 56 47.5 40. 4,60 0 65 48 06. 95 89.9 7 685.8 68 5. 598 8. 5,070 9 557 74 4.0 7 96.6 9 76.6 8 55. 779 7.4 6 --- --- --- --- --- --- --- --- 9 58.8 97 96. Diameter Wire Rope Application Max. Permissible Load in mm Front Hoist -- 8 Rear Hoist -- 8 Boom Hoist -- Third Drum.0 Type Wire Rope Descriptions lb kg ZB,900 5 77 4 X 7 Non Rotating, E.I.P.S., Right Regular or Right Lang Lay ZB,900 5 77 4 X 7 Non Rotating, E.I.P.S., Right Regular or Right Lang Lay FC 8,400 88 6 x 5 (6 x9 Class) - Swaged - Preformed - I.W.R.C - Right Lay - Regular Lay Compacted Strands 5.4 ZB 7,90 664 4 X 7 Non Rotating, E.I.P.S., Right Regular or Right Lang Lay
5776 (supersedes 576)-06-U Working Areas 60 Over Side Boom Over Drive End Over Idler End See Note Center Of Rotation Longitudinal Of Crawler See Note Idler Sprocket Drive Sprocket Over Side Note: These Lines Determine The Limiting Position Of Any Load For Operation Within Working Areas Indicated.
5776 (supersedes 576)-06-U Attachments BL Jib Auxiliary Tip Extension JE Main Boom JE Main Boom JE Main Boom JN 50 ft Extension 60-90 ft (8.9-88.9m) Main Boom JN 50 ft Extension 60-50 ft (8.9-76.0m) Main Boom With Auxiliary Tip Extension JN 50 ft Extension 60-50 ft (8.9-76.0m) Main Boom With 0-90 ft (9.4-7.4m) Jib
5776 (supersedes 576)-06-U Main Boom Make-up Boom Extensions ft (m) Boom Length ft (m) 0 (9.4) Base 60 (8.9) 80 (4.8) 90 (7.4) 0 (.5) 0 (6.58) 0 (9.6) 0 (6.0) HD 'JN' 0 (9.4) HD 'JN' 0 (.05) Std. 'JE' 0 (6.0) Std. 'JE' 0 (9.4) Std. 'JE' 40 (.9) Std. 'JE' 0 (9.4) Top 40 (4.67) 50 (45.7) 60 (48.77) 70 (5.8) 80 (54.86) 90 (57.9) 00 (60.96) 0 (64.0) 0 (67.06) 0 (70.0) 40 (7.5) 50 (76.0) 60 (79.5) 70 (8.0) 80 (85.4) 90 (88.9) Notes:. Capacities shown are in kips/metric tons ( kip =,000 lb / metric ton = 0.45 kips) and are not more than 75% of the tipping loads with the crane standing level on firm supporting surface. A deduction must be made from these capacities for weight of hook block, hook ball, sling, grapple, load weighing device, etc. When using main hook while jib or tip extension is attached, reduce capacities by values shown in Crane Rating Manual. See Operator's Manual for all limitations when raising or lowering attachment.. The capacities in the shaded areas are based on structural strength. The capacities in the non-shaded areas are based on stability ratings.. For recommended reeving, parts of line, wire rope type, and wire rope inspection, see Wire Rope Capacity Chart, Operator's Manual, and Parts Manual. 4. Load ratings are based on freely suspended loads and make no allowances for such factors as the effect of the wind, ground conditions, and operating speeds. The operator shall therefore reduce load ratings in order to take these conditions into account. Refer to the Crane Rating Manual for Wind Speed Restrictions. 5. The 5 ft (7.6m) live mast must be used for all capacities listed. 6. The least stable rated condition is over the side. 7. Booms must be erected and lowered over the end for maximum stability. 8. Main boom length must not exceed 90 ft (88.9m). 9. Do not operate at radii and boom lengths where the Crane Rating Manual lists no capacity. Do not use longer booms or jibs than those listed in the Crane Rating Manual. Any of the above can cause a tipping condition, or boom and jib failure. 0. These capacities are in compliance with ANSI/ASME B0.5 at date of manufacture.. These capacities apply only to the crane as originally manufactured and normally equipped by Link Belt Construction Equipment Company.
4 5776 (supersedes 576)-06-U Main Boom Working Range Diagram 60' TO 90' MAIN BOOM 40 0 00 80 60 40 0 00 80 60 40 Maximum Boom Angle See Note 0 00 80 60 40 0 0 0 80 00 8 90 70 80 80 70 60 60 60 50 40 50 0 0 0 0 00 40 00 90 80 80 70 60 60 50 0 Main Boom Length Height In Feet Above Ground 40 40 40 0 0 Minimum Boom Angle See Note 0 0 0 00 00 90 80 80 70 60 60 40 0 0 40 0 00 80 60 40 0 00 80 60 40 Operating Radius From Centerline Of Rotation 0 00 80 60 40 0 CL Of Rotation Notes:.. Boom geometry shown is for unloaded condition and crane standing level on firm supporting surface. Boom deflection, subsequent radius, and boom angle change must be accounted for when applying load to hook. Maximum and minimum boom angles are equal to the values listed in the capacity chart for each boom length.
5 5776 (supersedes 576)-06-U Main Boom Load Chart Main Boom Lift Capacity Chart - 60 Rotation - ABCDE + A [60,000 + 60,000 lb (7 575 + 7 6kg)] Counterweight [All capacities are listed in kips (mt)] Boom Length ft (m) Load Radius ft (m) 60 (8.) 4.0 (4.7) 500.0 (6.80) 4.0 (4.7) 5.0 (4.57) 458.0 (07.75) 5.0 (4.57) 6.0 (4.88) 4.4 (95.68) 47.6 (9.96) 7.0 (5.8) 407.7 (84.9) 405.4 (8.89) 40.9 (8.0) 7.0 (5.8) 8.0 (5.49) 86.4 (75.7) 84.4 (74.6) 8. (7.8) 8.0 (5.49) 9.0 (5.79) 67. (66.56) 65. (65.65) 64. (65.5) 58. (6.48) 0.0 (6.0) 49.7 (58.6) 47.8 (57.76) 46.8 (57.) 44.4 (56.) 9.8 (54.) 5.0 (7.6) 8. (7.96) 80.7 (7.) 79.9 (6.96) 78. (6.4) 77. (5.74) 75.5 (4.96) 69.4 (.0) 5.0 (7.6) 0.0 (9.4) 5.8 (06.96).5 (05.0) 9. (04.0) 5.4 (0.4).8 (0.5) 0.9 (00.0) 8. (98.97) 0.0 (9.4) 5.0 (0.67) 88. (85.) 87.9 (85.) 87.7 (85.4) 86.6 (84.64) 85. (84.0) 8.5 (8.78) 80. (8.69) 5.0 (0.67) 40.0 (.9) 55.4 (70.49) 55. (70.40) 55.0 (70.) 54.4 (70.0) 54. (69.90) 5.6 (69.67) 5.0 (69.40) 40.0 (.9) 50.0 (5.4) 4. (5.85) 4. (5.75).9 (5.66). (5.5).9 (5.). (50.94).7 (50.67) 50.0 (5.4) 60.0 (8.9) 89. (40.5) 89. (40.46) 89.0 (40.7) 88. (40.05) 88.0 (9.9) 87. (9.60) 86.6 (9.8) 60.0 (8.9) 70.0 (.4) 7. (.75) 7.5 (.89) 7.9 (.6) 7.6 (.48) 70.9 (.6) 70. (.84) 70.0 (.4) 80.0 (4.8) 60.7 (7.5) 60.6 (7.49) 59.9 (7.7) 59.6 (7.0) 59.0 (6.76) 58. (6.40) 80.0 (4.8) 5.5 (.6) 5.0 (.) 50.7 (.00) 50.0 (.68) 49. (.) 90.0 (7.4) 44.0 (9.96) 4.7 (9.8) 4.0 (9.50) 4.6 (9.) 00.0 (0.48) 8. (7.) 7.7 (7.0) 7.0 (6.78) 0.0 (.5) 0.0 (6.58).0 (4.97).4 (4.70) 0.0 (6.58) 0.0 (9.6) 9. (.4) 8.5 (.9) 0.0 (9.6) 40.0 (4.67) 5. (.4) 40.0 (4.67) 50.0 (45.7).4 (0.6) 50.0 (45.7) 90.0 (7.4) 00.0 (0.48) 80 (4.4) 90 (7.4) 0 (.5) 0 (6.6) 40 (4.7) 60 (48.8) Load Radius ft (m) 6.0 (4.88) 0.0 (.5) 9.0 (5.79) 0.0 (6.0) This material is supplied for reference use only. Operator must refer to in-cab Crane Rating Manual and Operator's Manual to determine allowable crane lifting capacities and assembly and operating procedures.
6 5776 (supersedes 576)-06-U Main Boom Lift Capacity Chart - 60 Rotation - ABCDE + A [60,000 + 60,000 lb (7 575 + 7 6kg)] Counterweight [All capacities are listed in kips (mt)] Boom Length ft (m) Load Radius ft (m) 80 (54.9) 00 (6.0) 0.0 (9.4) 0. (9.) 59.8 (7.48) 5.0 (0.67) 77.9 (80.69) 57.8 (7.58) 5.8 (57.06) 0. (46.6) 5.0 (0.67) 40.0 (.9) 5. (68.58) 49. (67.68).6 (55.6) 00.9 (45.77) 40.0 (.9) 50.0 (5.4).0 (50.5) 0. (50.0) 09.5 (49.67) 98. (44.59) 84. (8.9) 74.0 (.57) 68. (0.89) 50.0 (5.4) 60.0 (8.9) 85.8 (8.9) 85.0 (8.56) 84.8 (8.46) 84.0 (8.0) 78.8 (5.74) 69. (.4) 6.7 (8.89) 60.0 (8.9) 70.0 (.4) 69.5 (.5) 68.7 (.6) 67.9 (0.80) 67. (0.44) 66.4 (0.) 6.7 (8.44) 57. (5.95) 70.0 (.4) 80.0 (4.8) 57.5 (6.08) 56.6 (5.67) 55.8 (5.) 55.0 (4.95) 54. (4.58) 5.4 (4.) 5. (.7) 80.0 (4.8) 90.0 (7.4) 48.4 (.95) 47.6 (.59) 46.8 (.) 45.9 (0.8) 45. (0.46) 44. (0.05) 4.8 (9.87) 90.0 (7.4) 00.0 (0.48) 4.8 (8.96) 4.0 (8.6) 40. (8.) 9.4 (7.87) 8.6 (7.5) 7.8 (7.5) 7.4 (6.96) 00.0 (0.48) 0.0 (.5) 6. (6.4) 5.4 (6.06) 4.6 (5.69).7 (5.9).9 (4.9). (4.56).7 (4.8) 0.0 (.5) 0.0 (6.58).6 (4.) 0.8 (.97) 0.0 (.6) 9. (.0) 8. (.84) 7.4 (.4) 7.0 (.5) 0.0 (6.58) 0.0 (9.6) 7.7 (.56) 6.9 (.0) 6. (.84) 5. (.4) 4.4 (.07).5 (0.66). (0.48) 0.0 (9.6) 40.0 (4.67) 4.5 (.).7 (0.75).8 (0.4).0 (9.98). (9.57) 0. (9.6) 9.8 (8.98) 40.0 (4.67) 50.0 (45.7).7 (9.84) 0.9 (9.48) 0.0 (9.07) 8.8 (8.5) 8. (8.0) 7.4 (7.89) 7.0 (7.7) 50.0 (45.7) 60.0 (48.77) 9. (8.75) 8.4 (8.5) 7.4 (7.89) 6. (7.0) 5.8 (7.7) 5.0 (6.80) 4.5 (6.58) 60.0 (48.77) 70.0 (5.8) 7.0 (7.7) 6. (7.0) 4.9 (6.76).6 (6.7).7 (6.).8 (5.8).4 (5.6) 70.0 (5.8) 80.0 (54.86).8 (6.6).7 (5.76).5 (5.).8 (5.5) 0.9 (4.94) 0.5 (4.76) 80.0 (54.86) 90.0 (57.9).7 (5.) 0.7 (4.85) 9.5 (4.) 0. (4.58) 9. (4.7) 8.8 (.99) 90.0 (57.9) 00.0 (60.96) 8.9 (4.04) 7.8 (.54) 8.6 (.90) 7.7 (.49) 7. (.) 00.0 (60.96) 0.0 (64.0) 7. (.7) 6. (.8) 7. (.) 6.4 (.90) 5.9 (.68) 0.0 (64.0) 0.0 (67.06) 4.7 (.) 6. (.77) 5. (.6) 4.7 (.) 0.0 (67.06) 0.0 (70.0). (.50) 5.0 (.7) 4. (.86).6 (.6) 0.0 (70.0).9 (.77).0 (.6).6 (.8) 40.0 (7.5) 50.0 (76.0). (0.95).7 (0.77) 50.0 (76.0) 60.0 (79.5). (0.59) 0.8 (0.6) 60.0 (79.5) 0 (67.) 40 (7.) 60 (79.) 80 (85.) 90 (88.4) Load Radius ft (m) 0.0 (9.4) 40.0 (7.5) This material is supplied for reference use only. Operator must refer to in-cab Crane Rating Manual and Operator's Manual to determine allowable crane lifting capacities and assembly and operating procedures.
7 5776 (supersedes 576)-06-U Jib Attachment Make-up Jib Length ft (m) Jib Extensions Jib Extensions 0 ft (.05m) 0 ft (6.0m) 0 (9.4) 40 (.9) 50 (5.4) 60 (8.9) 70 (.4) 80 (4.8) 90 (7.4) Notes:. Capacities shown are in kips/metric tons ( kip =,000 lb / metric ton = 0.45 kips) and are not more than 75% of the tipping loads with the crane standing level on a firm supporting surface.. A deduction must be made from these capacities for the weight of the main boom hook block or hook ball, jib hook block or hook ball, slings, grapples, load weighing devices, etc. When using main hook while jib is attached, reduce capacities by values shown in Crane Rating Manual. See Operator's Manual for all limitations when raising or lowering attachment.. The capacities in the shaded areas are based on structural strength. The capacities in the non-shaded areas are based on stability ratings. 4. Load ratings are based on freely suspended loads and make no allowances for such factors as the effect of the wind, ground conditions, and operating speeds. The operator shall therefore reduce load ratings in order to take these conditions into account. Refer to the Crane Rating Manual for Wind Speed Restrictions. 5. These capacities are for ABCDE+A counterweight. 6. These capacities are for 60 working areas. 7. These capacities are for 0-90 ft (9.5-7.4m) jib lengths only. 8. The jib cannot be used on boom lengths over 70 ft (8.0m). 9. The least stable rated condition is over the side. 0. These capacities are in compliance with ASME/ANSI B0.5 at date of manufacture.. These capacities apply only to the crane as originally manufactured and normally equipped by Link Belt Construction Equipment Company.
8 5776 (supersedes 576)-06-U Jib Attachment Working Range Diagram Maximum Boom Angle See Note 60' TO 70' MAIN BOOM WITH 0' TO 90' JIB 00 80 60 40 0 00 80 60 40 0 00 80 60 40 0 0 0 80 80 8 0 0 60 60 70 90 40 40 80 60 70 0 0 60 50 00 00 40 50 Main Boom + Jib Length 400 400 80 80 60 60 50 40 40 40 0 0 0 00 90 0 00 80 80 0 70 60 60 50 40 40 0 Main Boom Length Height in feet above ground 0 0 Minimum Boom Angle See Note 0 0 0 00 00 90 80 80 70 60 60 40 0 0 00 Notes:.. 80 60 40 0 00 80 60 40 Operating Radius From Centerline Of Rotation 0 00 80 60 40 0 C L Of Rotation Boom geometry shown is for unloaded condition and crane standing level on firm supporting surface. Boom deflection, subsequent radius, and boom angle change must be accounted for when applying load to hook. Maximum and minimum boom angles are equal to the values listed in the capacity chart for each boom length.
9 5776 (supersedes 576)-06-U Jib Attachment Load Charts 0 ft (9.5m) Offset Jib Length - 60_ Rotation - ABCDE + A [60,000 + 60,000 lb (7 575 + 7 6kg)] Counterweight [All capacities are listed in kips (mt)] 0 Offset 0 Offset Main Boom Length ft (m) 0 Offset 5.0 (7.6) 7.5 (.4) 5.0 (7.6) 0.0 (9.4) 7.4 7.5 (.9) (.4) 0.0 (9.4) 67.8 (0.75) 0.0 (9.4) 5.0 (0.67) 69.6 7.4 (.57) (.84) 5.0 (0.67) 66.5 (0.6) 5.0 (0.67) 48. (.86) 40.0 (.9) 67.9 7. 7. (0.80) (.5) (.5) 40.0 (.9) 6. 66.9 (8.7) (0.5) 40.0 (.9) 45. 49.6 (0.55) (.50) 50.0 (5.4) 65. 68.9 69.4 66.4 (9.6) (.5) (.48) (0.) 50.0 (5.4) 54. 65. 65. (4.58) (9.5) (9.6) 50.0 (5.4) 8.0 46.0 48.7 (7.4) (0.87) (.09) 60.0 (8.9) 56.9 65.4 67.9 65.0 6.6 (5.8) (9.66) (0.80) (9.48) (7.94) 60.0 (8.9) 48. 59.6 64. 6.6 58.5 (.86) (7.0) (9.) (7.94) (6.54) 60.0 (8.9) 4.9 4.0 46. 48.0 (5.8) (9.50) (0.9) (.77) 70.0 (.4) 49.8 60.4 66.5 6.8 59.8 (.59) (7.40) (0.6) (8.94) (7.) 70.0 (.4) 4.8 55.0 6. 60.6 56. (9.87) (4.95) (8.7) (7.49) (5.45) 70.0 (.4).6 40.5 4.9 46. 46.9 (4.79) (8.7) (9.9) (0.9) (.7) 80.0 (4.8) 44.5 5.4 57.9 55.4 54. (0.8) (.) (6.6) (5.) (4.58) 80.0 (4.8) 5. 58.4 56.4 54.0 (.8) (6.49) (5.58) (4.49) 80.0 (4.8) 5.8 4.0 44. 45. (6.4) (9.05) (0.09) (0.50) 90.0 (7.4) 44.5 48.9 46. 45. (0.8) (.8) (.00) (0.46) 90.0 (7.4) 47.9 49.5 47. 46.0 (.7) (.45) (.6) (0.87) 90.0 (7.4) 4. 7.4 4.8 4.7 (5.5) (6.96) (9.4) (9.8) 00.0 (0.48) 8.8 4.9 9. 8.5 (7.60) (9.0) (7.78) (7.46) 00.0 (0.48) 44.7 4.4 9.9 8.8 (0.8) (9.) (8.0) (7.60) 00.0 (0.48).9 6. 40.6 9.5 (4.9) (6.7) (8.4) (7.9) 0.0 (.5) 4.5 6.6 4.0.8 (5.65) (6.60) (5.4) (4.88) 0.0 (.5) 9. 7.0 4.6.5 (7.74) (6.78) (5.69) (5.0) 0.0 (.5).8 4.9 5. 4. (4.4) (5.8) (5.97) (5.5) 0.0 (6.58) 0.7.0 9.4 8. (.9) (4.5) (.4) (.75) 0.0 (6.58) 4.6. 9.9 8.7 (5.69) (4.65) (.56) (.0) 0.0 (6.58).7 0.4 9. (4.8) (.79) (.9) 0.0 (9.6) 8. 5.4 4. (.75) (.5) (0.98) 0.0 (9.6) 8.4 6.0 4.8 (.88) (.79) (.5) 0.0 (9.6) 8.7 6.4 5. (.0) (.97) (.48) 40.0 (4.67) 4.9 (.9).7 (9.84) 0.9 (9.48) 40.0 (4.67) 5.. (.9) (0.).4 (9.7) 40.0 (4.67) 5.4.8 (.5) (0.4).9 (9.9) 50.0 (45.7). (0.0) 8.6 (8.44) 8. (8.) 50.0 (45.7). (0.) 9.0 (8.6) 8.5 (8.9) 50.0 (45.7) 9.5 (8.85) 8.9 (8.57) 60.0 (48.77) 9.7 (8.94) 5.8 (7.7) 5. (6.94) 60.0 (48.77) 9.8 (8.98) 6. (7.5) 5.8 (7.7) 60.0 (48.77) 6.6 (7.5) 6. (7.9) 70.0 (5.8) 7. (7.85).4 (6.08).8 (5.8) 70.0 (5.8) 7.4 (7.89).7 (6.). (6.0) 70.0 (5.8) 4. (6.40).7 (6.) 80.0 (54.86) 5.0 (6.80). (5.) 0.6 (4.8) 80.0 (54.86).5 (5.). (5.0) 80.0 (54.86).8 (5.5).4 (5.7) 9.4 (4.6) 8.7 (.95) 90.0 (57.9) 9.6 (4.5) 9. (4.) 90.0 (57.9) 9.4 (4.6) 7.6 (.45) 7.0 (.8) 00.0 (60.96) 7.8 (.54) 7. (.) 00.0 (60.96) 7.60 (.45) 0.0 (64.0) 6. (.77) 5.4 (.45) 0.0 (64.0) 6. (.8) 5.7 (.59) 0.0 (64.0) 0.0 (67.06) 4.7 (.) 4.0 (.8) 0.0 (67.06) 4. (.95) 0.0 (67.06) 0.0 (70.0). (.50).7 (.) 0.0 (70.0).9 (.) 0.0 (70.0) 40.0 (7.5). (0.95) 80 (54.9) 90.0 (57.9) 00.0 (60.96) 00.0 (60.96) 40 (7.) 70 (8.) 0 (.5) 0 (6.6) 80 (54.9) 40 (7.) 70 (8.) Load Radius ft (m) Main Boom Length ft (m) 60 (8.) 0 (6.6) Load Radius ft (m) Main Boom Length ft (m) Load Radius ft (m) 0 (.5) 0 (6.6) 80 (54.9) 40 (7.) 70 (8.) 5.0 (7.6) 40.0 (7.5) 40.0 (7.5) 50.0 (76.0) 50.0 (76.0) 50.0 (76.0) 60.0 (79.5) 60.0 (79.5) 60.0 (79.5) 70.0 (8.0) 70.0 (8.0) 70.0 (8.0) This material is supplied for reference use only. Operator must refer to in-cab Crane Rating Manual and Operator's Manual to determine allowable crane lifting capacities and assembly and operating procedures.
0 5776 (supersedes 576)-06-U 60 ft (8.50m) Offset Jib Length - 60_ Rotation - ABCDE + A [60,000 + 60,000 lb (7 575 + 7 6kg)] Counterweight [All capacities are listed in kips (mt)] 0 Offset 0 Offset Main Boom Length ft (m) 0 Offset 5.0 (0.67) 8.9 (7.64) 5.0 (0.67) 5.0 (0.67) 40.0 (.9) 7.7 4. (7.0) (9.60) 40.0 (.9) 40.0 (.9) 50.0 (5.4) 5.7 7.5 7.6 (6.9) (7.0) (7.06) 50.0 (5.4).8 4.8 (5.) (5.79) 50.0 (5.4) 9.9 (.56) 60.0 (8.9).8 6. 6.6 5.7 (5.) (6.7) (6.60) (6.9) 60.0 (8.9)..7.9 (4.56) (5.9) (5.8) 60.0 (8.9) 7. 9. (.9) (.0) 70.0 (.4). 4.9 5.6 4.9 4.0 (4.56) (5.8) (6.5) (5.8) (5.4) 70.0 (.4) 9.8.6..4 (.5) (4.79) (5.0) (4.70) 70.0 (.4) 4.9 7. 8.6 (.9) (.8) (.97) 80.0 (4.8) 9.6.8 4.7 4.. (.4) (5.) (5.74) (5.5) (5.0) 80.0 (4.8) 6.9.6.4.8. (.0) (4.) (4.70) (4.4) (4.) 80.0 (4.8).0 5.7 7. 8. 8.7 (0.4) (.66) (.8) (.84) (.0) 90.0 (7.4) 6.6.6.9.5.6 (.07) (4.79) (5.8) (5.0) (4.79) 90.0 (7.4) 4.6 0.5.7. 0.5 (.6) (.8) (4.8) (4.0) (.8) 90.0 (7.4).6 (9.80) 4.4 6. 7. 7.7 (.07) (.88) (.8) (.56) 00.0 (0.48) 4..6..8.0 (0.98) (4.) (5.0) (4.88) (4.5) 00.0 (0.48).7 8.4.0 0.7 0.0 (0.0) (.88) (4.06) (.9) (.6) 00.0 (0.48) 0.4 (9.5). 5. 6.4 6.8 (0.57) (.9) (.97) (.6) 0.0 (.5). 0..4.. (0.07) (.70) (4.70) (4.6) (4.0) 0.0 (.5) 6.7 0.4 0. 9.5 (.) (.79) (.70) (.8) 0.0 (.5). 4. 5.5 6.0 (0.) (0.98) (.57) (.79) 0.0 (6.58) 8..7 0.9 9.7 (.75) (4.8) (4.0) (.47) 0.0 (6.58) 5. 9. 9.8 9.0 (.4) (.4) (.5) (.5) 0.0 (6.58).4 (9.7). 4.7 5. (0.57) (.0) (.48) 0.0 (9.6) 6. 9.5 6.9 5.7 (.9) (.8) (.0) (.66) 0.0 (9.6).9 7.8 8.0 6.9 (0.84) (.6) (.70) (.0) 0.0 (9.6) 0.7 (9.9).6 4.0 4.5 (0.5) (0.89) (.) 40.0 (4.67) 4.7 6..5. (.0) (.88) (0.66) (0.) 40.0 (4.67).7 6.5 4.5.4 (0.0) (.0) (.) (0.6) 40.0 (4.67).9 (9.9)..9 (0.57) (0.84) 50.0 (45.7)..4 (0.57) (0.6) 0. (9.) 9.5 (8.85) 50.0 (45.7).8 (9.89) 60.0 (48.77). (0.0) 0.9 (9.48) 7.5 (7.94) 6.9 (5.0) 70.0 (5.8) 8.8 (8.5) 5. (6.85) 80.0 (54.86) 6.9 (7.67) 90.0 (57.9) 80 (55.5) 40 (74.0) 70 (8.7) 0 (.5) 0 (6.6) 80 (54.9) 40 (7.) 70 (8.) Load Radius ft (m) Main Boom Length ft (m) 60 (8.50) 0 (7.0) Load Radius ft (m) Main Boom Length ft (m) Load Radius ft (m) 0 (.5) 0 (6.6) 80 (54.9) 40 (7.) 70 (8.).9 (0.84). (9.66) 0.4 (9.5) 50.0 (45.7). (9.66). (0.). (9.66) 60.0 (48.77).4 (9.7) 8.4 (8.5) 7.8 (8.07) 60.0 (48.77) 0.7 (9.9) 9. (8.75) 8.6 (8.44) 4.4 (6.5) 70.0 (5.8) 9. (8.7) 5.9 (7.) 5.4 (6.99) 70.0 (5.8) 9.6 (8.89) 6.7 (7.57) 6. (7.9).9 (5.85). (5.5) 80.0 (54.86) 7. (7.80).6 (6.7). (5.94) 80.0 (54.86) 4. (6.49).9 (6.0) 4.9 (6.76).0 (4.99) 0. (4.6) 90.0 (57.9) 5. (6.94).6 (5.6). (5.0) 90.0 (57.9). (5.58).8 (5.5) 00.0 (60.96). (5.94) 9. (4.7) 8.5 (.86) 00.0 (60.96) 9.8 (4.45) 9. (4.) 00.0 (60.96) 0.4 (4.7) 9.9 (4.49) 0.0 (64.0).4 (5.7) 7.7 (.49) 6.9 (.) 0.0 (64.0) 8. (.7) 7.6 (.45) 0.0 (64.0) 8.7 (.95) 8. (.7) 0.0 (67.06) 6. (.8) 5.4 (.45) 0.0 (67.06) 6.7 (.04) 6. (.77) 0.0 (67.06) 6.6 (.99) 0.0 (70.0) 4.9 (.) 4. (.86) 0.0 (70.0) 5. (.40) 4.7 (.) 0.0 (70.0) 5. (.6) This material is supplied for reference use only. Operator must refer to in-cab Crane Rating Manual and Operator's Manual to determine allowable crane lifting capacities and assembly and operating procedures.
5776 (supersedes 576)-06-U 90 ft (7.76m) Offset Jib Length - 60_ Rotation - ABCDE + A [60,000 + 60,000 lb (7 575 + 7 6kg)] Counterweight [All capacities are listed in kips (mt)] 0 Offset Load Radius ft (m) 0 Offset Main Boom Length ft (m) 60 (8.) 0 (6.6) 80 (54.9) 40 (7.) 70 (8.) Load Radius ft (m) 0 Offset Main Boom Length ft (m) 0 (.5) 0 (6.6) 80 (54.9) 40 (7.) 50.0 (5.4).5 4.5 (0.66) (.) 50.0 (5.4) 60.0 (8.9).0 (9.98).4.8 (0.6) (0.80) 60.0 (8.9) 0.6 (9.4) 70.0 (.4) 0.7 (9.9)..0.8 (0.) (0.4) (0.4) 70.0 (.4) 9.4 (8.80) 0. (9.) 80.0 (4.8) 9.4 (8.80). (9.66).. (0.07) (0.).9 (9.9) 80.0 (4.8) 8. (8.0) 9.5 (8.85) 0.0 (9.07) 90.0 (7.4) 8. (8.0) 0.4 (9.5).4 (9.7).6 (9.80).5 (9.75) 90.0 (7.4) 7. (7.85) 8.7 (8.48) 9.4 (8.80) 9.5 (8.85) 00.0 (0.48) 7. (7.85) 9.5 (8.85) 0.7 (9.9). (9.57) 0.9 (9.48) 00.0 (0.48) 6.5 (7.48) 8.0 (8.6) 8.8 (8.5) 0.0 (.5) 6.4 (7.44) 8.7 (8.48) 0.0 (9.07) 0.5 (9.0) 0.4 (9.5) 0.0 (.5) 5.7 (7.) 7. (7.85) 0.0 (6.58) 5.6 (7.08) 8.0 (8.6) 9.4 (8.80) 9.9 (9.0) 9.9 (9.0) 0.0 (6.58) 4.9 (6.76) 0.0 (9.6) 4.7 (6.67) 7. (7.85) 8.8 (8.5) 9.4 (8.80) 9.4 (8.80) 0.0 (9.6) 4.0 (6.5) 40.0 (4.67).7 (6.) 6.6 (7.5) 8. (8.6) 8.9 (8.57) 9.0 (8.6) 50.0 (45.7) 6. (7.0) 7.7 (8.0) 8.5 (8.9) 60.0 (48.77) 5.5 (7.0) 7. (7.76) 70.0 (5.8) 5.0 (6.80) 80.0 (54.86) 90.0 (57.9) 70 (8.) Load Radius ft (m) Main Boom Length ft (m) 0 (.5) 0 (6.6) 80 (54.9) 40 (7.) 70 (8.) 50.0 (5.4) 60.0 (8.9) 70.0 (.4) 8. (8.0) 80.0 (4.8) 7. (7.85) 8.0 (8.6) 9. (8.75) 90.0 (7.4) 6.5 (7.48) 7. (7.85) 7.6 (7.98) 9.0 (8.6) 8.9 (8.57) 00.0 (0.48) 5.7 (7.) 6.7 (7.57) 7. (7.76) 7. (7.80) 6.5 (7.48) 8. (8.6) 8.5 (8.9) 8.4 (8.5) 0.0 (.5) 5.0 (6.80) 6. (7.5) 6.7 (7.57) 6.8 (7.6) 6. (7.9) 6.7 (7.57) 7.7 (8.0) 8.0 (8.6) 8.0 (8.6) 0.0 (6.58) 4. (6.40) 5.7 (7.) 6. (7.9) 6.4 (7.44) 6. (7.5) 6. (7.5) 7. (7.80) 7.6 (7.98) 7.6 (7.98) 0.0 (9.6) 5. (6.89) 5.9 (7.) 6. (7.0) 6. (7.0) 40.0 (4.67) 5.6 (7.08) 6.7 (7.57) 7. (7.80) 7. (7.80) 40.0 (4.67) 4.8 (6.7) 5.5 (7.0) 5.8 (7.7) 5.8 (7.7) 8.5 (8.9) 50.0 (45.7) 5. (6.89) 6. (7.9) 6.8 (7.6) 6.8 (7.6) 50.0 (45.7) 4. (6.44) 5. (6.89) 5.5 (7.0) 5.5 (7.0) 8.0 (8.6) 8.0 (8.6) 60.0 (48.77) 4.6 (6.6) 5.9 (7.) 6.4 (7.44) 6.5 (7.48) 60.0 (48.77).7 (6.) 4.9 (6.76) 5. (6.89) 5. (6.89) 6.6 (7.5) 6. (7.9) 5.7 (7.) 70.0 (5.8) 4.0 (6.5) 5.5 (7.0) 6. (7.0) 6. (7.5) 70.0 (5.8) 4.6 (6.6) 4.9 (6.76) 4.9 (6.76) 4. (6.49) 6. (7.5) 4. (6.40).4 (6.08) 80.0 (54.86).5 (6.) 5. (6.85) 5. (6.94) 4.8 (6.7) 80.0 (54.86) 4. (6.44) 4.7 (6.67) 4.7 (6.67).7 (6.) 5.8 (7.7). (5.5).4 (5.7) 90.0 (57.9) 4.8 (6.7). (6.0).7 (5.76) 90.0 (57.9).8 (6.6) 4. (6.49).9 (6.0) 00.0 (60.96) 4.4 (6.5) 0.4 (4.7) 9.7 (4.40) 00.0 (60.96) 4.4 (6.5).4 (5.7) 0.8 (4.90) 00.0 (60.96).4 (6.08). (5.58).9 (5.40) 0.0 (64.0).7 (5.76) 8.9 (4.04) 8. (.67) 0.0 (64.0). (6.0) 9.8 (4.45) 9. (4.) 0.0 (64.0) 0.6 (4.8) 0. (4.58) 0.0 (67.06). (5.) 7.4 (.6) 6.6 (.99) 0.0 (67.06).7 (5.) 8. (.7) 7.6 (.45) 0.0 (67.06) 9.0 (4.08) 8.5 (.86) 0.0 (70.0) 9.9 (4.49) 6. (.77) 5. (.40) 0.0 (70.0) 6. (.8) 0.0 (70.0) 7.5 (.40) 7.0 (.8) This material is supplied for reference use only. Operator must refer to in-cab Crane Rating Manual and Operator's Manual to determine allowable crane lifting capacities and assembly and operating procedures.
5776 (supersedes 576)-06-U Luffing Attachment Luffing Boom Make-up JN' Extensions Luffing Boom Length ft (m) 0 ft (9.0m) Base Section 0 ft (6.4m) 0 ft (9.0m) 0 (.5m) 0 (6.6m) 0 (9.6m) 40 (4.7m) 50 (45.7m) 60 (48.8m) 70 (5.8m) 80 (54.9m) 90 (57.9m) JE' Extensions 0 ft (.05m) 0 ft (6.4m) 0 ft (9.0m) 40 ft (.9m) 0 ft (9.0m) Top Section Luffing Jib Make-up Luffing Jib Extensions Luffing Jib Length ft (m) 5 ft (7.6m) Jib Base Section 85 (5.9m) 95 (8.9m) 05 (.0m) 5 (5.m) 5 (8.m) 5 (4.m) 45 (44.m) 55 (47.m) 65 (50.m) 75 (5.m) 85 (56.4m) 95 (59.4m) 0 ft (.05m) 0 ft (6.4m) 0 ft (9.0m) 0 ft (9.0m) Top Section 40 ft (.9m) Notes:. Capacities shown are in kips/metric tons ( kip =,000 lb / metric ton = 0.45 kips) and are not more than 75% of the tipping loads with the crane standing level on a firm supporting surface. A deduction must be made from these capacities for the weight of the hook block, hook ball, sling, grapple, load weighing devices, etc. When lifting from the luffing jib with the fixed jib installed, reduce capacities by values shown in the Crane Rating Manual. See Operator's Manual for all limitations when raising or lowering attachment.. The capacities in the shaded areas are based on structural strength. The capacities in the non-shaded areas are based on stability ratings.. All luffing attachment combinations require the maximum counterweight combination ABCDE. 4. Load ratings are based on freely suspended loads and make no allowances for such factors as the effect of the wind on load, ground conditions, and operating speeds. The operator shall therefore reduce load ratings in order to take these conditions into account. Refer to the Crane Rating Manual for Wind Speed Restrictions. 5. Refer to the Crane Rating Manual for allowable attachment liftoff lengths and allowable working lengths at the various luffing boom angles. 6. The fixed jib has only one length [0 ft (9.4m)] and only one offset with respect to the luffing jib (5 ). 7. These capacities are in compliance with ANSI/ASME B0.5 at date of manufacture. 8. These capacities apply only to the crane as originally manufactured and normally equipped by Link Belt Construction Equipment Company. * See Link-Belt website, www.linkbelt.com, for complete luffing attach ment working range details and capacities including fixed jib and midfall.
5776 (supersedes 576)-06-U This Page Intentionally Blank
4 5776 (supersedes 576)-06-U This Page Intentionally Blank
5 5776 (supersedes 576)-06-U This Page Intentionally Blank
5776 (supersedes 576)-06-U Link Belt Construction Equipment Company Lexington, Kentucky www.linkbelt.com Link Belt is a registered trademark. Copyright 06. We are constantly improving our products and therefore reserve the right to change designs and specifications. Powered by TCPDF (www.tcpdf.org)