Operating & Service Manual PL9-6026EN 0/0/205 Airetool Gas Line Cleaners Range: 3/4 (9.05mm) to -/2 (38.0mm) For additional product information visit our website at http://www.apextoolgroup.com
PL9-6026EN 0/0/205 Airetool Gas Line Cleaners Gas Line Cleaner - Specifications Model 40546 (27 GLC 50) (X 64 GLC 50) (X 6 GLC 50) 405354 (X 63 A GLC 25) 405355 (X 63 A GLC 50) 405573 (X 65 GLC 25) 404724 (X 65 A GLC 25) 405359 (X 65 A GLC 50) Pipe I.D. (mm) 3/4" (9.05) " (25.4) -/8" (28.58) -/4" (3.7) -/4" (3.7) -/2" (38.) -/2" (38.) -/2" (38.) Motor Assembly * 407500 (27) 4090200 (X 64) 4089900 (X 6) 409000 (X 63 A) 409000 (X 63 A) 4090300 (X 65) 4090400 (X 65 A) 4090400 (X 65 A) * Note: Refer to appropriate parts list page Motor Diameter (mm) /6" (7.46) /6" Head Assembly * 404802 (2740 S) (7.46) (2640 S) 7/8" (22.23) (340 S) -/6" 404903 (26.9) (6340 S) -/6" 404903 (26.9) (6340 S) -3/6" 404903 (30.6) (6340 S) -3/6" (30.6) (740 S) -3/6" 4074600 (30.6) (X 6540) Air Inlet (mm) /4" (6.35) /4" (6.35) /4" (6.35) Hose Size (mm) /4" (6.35) /4" (6.35) /4" (6.35) Hose Length (M) 50' (5.24) 50' (5.24) 50' (5.24) 25' (7.62) 50' (5.24) 25' (7.62) 25' (7.62) 50' (5.24) Motor Assembly: Illustrations B and C Head Assembly: Illustration A Page 2
Airetool Gas Line Cleaners PL9-6026EN 0/0/205 The original language of this manual is English. Product Safety Information: Intended Use: These pneumatic motors are to be used for small bent tube cleaning applications. WARNING These motors must not be modified in any manner unless approved in writing by, LLC or GmbH & Co. OHG. All safety devices must be properly installed and maintained in good working order. Service and Repair: Tool service and repair should be performed by an authorized, LLC or GmbH & Co. OHG Center. Refer to the last page of this manual for locations. Disposal: Observe local disposal guidelines for all components of this tool and its packaging. Copyright Protection:, LLC or GmbH & Co. OHG reserves the right to modify, supplement or improve this document or the product without prior notice. This document may not be reproduced in any way, shape or form, in full or parts thereof, or copied to another natural or machine readable language or to a data carrier, whether electronic, mechanical, optical or otherwise without the express permission of Apex Tool Group, LLC or GmbH & Co. OHG. Motor Operation and Maintenance: The following operation and maintenance guidelines for the Airetool cleaning motors must be met to ensure peak performance and long life. The motor must be connected to a filtered air supply at all times. The air supply hose must be the correct diameter in order to provide the proper air pressure and volume to the motor. An airline lubricator should be installed as close to the motor as possible. Use SAE 20 weight oil. Replacement motor parts should be primed with oil in the tool crib prior to being put into operation. Air supply lines and hoses should be primed with additional oil on systems with 25-50 feet of supply hose between the lubricator and the motor to ensure that the motor is being well lubricated during initial operation. During operation, a sufficient amount of oil must be dispersed to exhaust fog from the motor while it is running. Motors must be supplied with 20-50 drops of oil (depending on the motor size) per minute through the supply hose to maintain exhaust fog. When cleaning operations are completed, the motor must be flushed with oil before storing or left in an oil bath between uses.the tail hose on the motor should not be immersed in oil. Motor Assembly Notes: 60 Series Motors: When installing the rotor blades into the rotor, make sure the convex edge of the rotor blades are facing the center of the rotor. Page 3
PL9-6026EN 0/0/205 Airetool Gas Line Cleaners - Head Assembly A Link Pin Jaw (Motor End) Jaw (Cutter End) Link Link Pin Cone Cutter Cutter Pin Cone Cutter Page 4
Airetool Gas Line Cleaners - Head Assembly PL9-6026EN 0/0/205 Cleaning Head - Parts List Model 404802 (2740 S) (2640 S) Jaw (Motor End) Jaw (Cutter End) Component Parts Link Link Pin Cone Cutter Cutter Pin # # # # # # 094800 094800 09500 095200 2 2 06600 065900 (6453 V) (6453 V) (6454 V) (6455 V) (2947 S) (2944) (340 S) 404903 (6340 S) 0000 (6652) 00200 (6653) 00300 (6654) 2 00400 Link Pin 2 045200 (397 S) 059400 (2544 S) (740 S) 4074600 (X 6540) 0000 (6652) 00200 (6653) 00300 (6654) 2 00400 Link Pin 097600 (6547) 059400 (2544 S) Page 5
PL9-6026EN 0/0/205 Airetool Gas Line Cleaners - Midget Motors B Models: 407500 (27) 409000 (X 63 A) 4090400 (X 65 A) Rear Head Machine Coupling Case Page 6
Airetool Gas Line Cleaners - Midget Motors PL9-6026EN 0/0/205 Midget Motors - Gas Line Cleaner - Specifications Model 407500 (27) 409000 (X 63 A) 409000 (X 63 A) Motor O.D. Tube I.D. /6" 3/4" -/6" -/4" -3/6" - Thread /4" N.F. N.F. N.F. Hose Size /4" Midget Motors - Gas Line Cleaner Motor 407500 (27) 409000 (X 63 A) 409000 (X 63 A) Component Parts Case Rear Head Machine Coupling Dowel Pin * Shaft Wrench # # # # # # # 062600 062800 062900PT 063000 06300 067500 3240200 4 (X 270) (X 2703) (X 2704) (X 2705) (2706) (302) (3/6") 333300 (X 630) 336300PT (X 650) * Note: Dowel Pin (Not Shown) 333400 (X 6303) 336400 (X 6503) 333600 (X 6304 A) 336600 (X 6504 A) 333700 (X 6305) 336700 (X 6505) 4 4 333800 (X 6306) 336800 (X 6506) 334000 (X 632) 334000 (X 632) 4-0805 (5/6") 4-0805 (5/6") Page 7
PL9-6026EN 0/0/205 Airetool Gas Line Cleaners - 60 Series Motors C Models: 4090200 (X 64) 4089900 (X 6) 4090300 (X 65) Tail Hose Coupling Rear Ferrule Tail Hose Front Ferrule Rear Head Machine Coupling Case Page 8
Airetool Gas Line Cleaners - 60 Series Motors PL9-6026EN 0/0/205 60 Series Motors - Gas Line Cleaner - Specifications Model 4090200 (X 64) 4089900 (X 6) 4090300 (X 65) Motor O.D. /6" 7/8" -3/6" Tube I.D. (Radius) 3/6" (5") -/32" (5") -/2" (6") 60 Series Motors - Gas Line Cleaner Model 4090200 (X 64) 4089900 (X 6) 4090300 (X 65) * Note: Parts not shown Thread /4" N.F. 5/6" N.F. N.F. Hose Size # # # # # # 334800 335200 335300 334900 4 2 335400 3240200 (X 640) (X 6405) (X6406) (X 6403) (X 642) (3/6") 33200 33600 33700 33300 4 2 33800 4-0804 (X 60) (X 605) (X 606) (X 603) (X 62) (/4") 336300PT 336700 336800 336400 4 2 334000 4-0805 (X 650) (X 6505) (X 6506) (X 6503) (X 632) (5/6") Parts List Continued Below /4" /4" Component Parts Read Head Case (with Bearing) Rear Dowel * Shaft Wrench * 60 Series Motors - Gas Line Cleaner (continued) Model 4090200 (X 64) 4089900 (X 6) 4090300 (X 65) Component Parts Tail Hose Machine Front Tail Hose Rear Tail Hose Assembly Coupling Ferrule Coupling Ferrule # # # # # # 335000 335700 335500 335600 335800 (X 649) (X 6404) (X 647) (X 645) (X 646) (X 648) 33400 33200PT 33900 332000 332200 (X 69) (X 604) (X 67) (X 65) (X 66) (X 68) 336500 334300 33400 334200 334400 (X 659) (X 6504) (X 637) (X 635) (X 636) (X 638) Page 9
POWER TOOLS SALES & SERVICE CENTERS Please note that all locations may not service all products. Contact the nearest Sales & Service Center for the appropriate facility to handle your service requirements. NORTH AMERICA SOUTH AMERICA Detroit, Michigan 2630 Superior Court Auburn Hills, MI 48236 Phone: + (248) 393-5640 Fax: + (248) 39-6295 Lexington, South Carolina 670 Industrial Drive Lexington, SC 29072 Phone: + (800) 845-5629 Phone: + (99) 387-0099 Fax: + (803) 358-768 Louisville, Kentucky 000 Glengarry Drive Suite 50 Fairdale, KY 408 Phone: + (502) 708-3400 apexpowertools.com/service Canada Apex Tool Canada, Ltd. 763 Bath Road Mississauga, Ontario L4T 3T Canada Phone: (866) 69-622 Fax: (905) 673-4400 Mexico Manufacturing México S. de R.L. de C.V. Vialidad El Pueblito #03 Parque Industrial Querétaro Querétaro, QRO 76220 Mexico Phone: +52 (442) 2 3800 Fax: +52 (800) 685 5560 Brazil Ind. Com. Ferram, Ltda. Av. Liberdade, 4055 Zona Industrial Iporanga Sorocaba, São Paulo CEP# 8087-70 Brazil Phone: +55 5 3238 3820 Fax: +55 5 3238 3938 EUROPE MIDDLE EAST AFRICA England GmbH & Co. OHG C/O Spline Gauges Piccadilly, Tamworth Staffordshire B78 2ER United Kingdom Phone: +44 827 8727 7 Fax: +44 827 874 28 France S.A.S. 25 rue Maurice Chevalier B.P. 28 7783 Ozoir-La-Ferrière Cedex, France Phone: +33 64 43 22 00 Fax: +33 64 43 7 7 Germany GmbH & Co. OHG Industriestraße 73463 Westhausen Germany Phone: +49 (0) 73 63 8 0 Fax: +49 (0) 73 63 8 222 Hungary Hungária Kft. Platánfa u. 2 9027 Györ Hungary Phone: +36 96 66 383 Fax: +36 96 66 35 ASIA PACIFIC Australia 59 Nurigong Street, Albury NSW 2640 Australia Phone: +6 2 6058 0300 Japan Japan Korin-Kaikan 5F, 3-6-23 Shibakoen, Minato-Ku, Tokyo 05-00, JAPAN Phone: +8-3-6450-840 Fax: +8-3-6450-84 China Apex Power Tool Trading (Shanghai) Co., Ltd Building A8, No. 38 Dongsheng Road Pudong, Shanghai China 2020 Phone: +86 2 60880320 Fax: +86 2 60880298 Korea Korea #503, Hibrand Living Bldg., 25 Yangjae-dong, Seocho-gu, Seoul 37-924, Korea Phone: +82-2-255-0250 Fax: +82-2-255-0252 Airetool India Apex Power Tools India Private Limited Gala No., Plot No. 5 S. No. 234, 235 & 245 Indialand Global Industrial Park Taluka-Mulsi, Phase I Hinjawadi, Pune 4057 Maharashtra, India Phone: +9 020 6676, LLC 000 Lufkin Road Apex, NC 27539 Phone: + (99) 387-0099 Fax: + (99) 387-264 www.apexpowertools.com PL9-6026EN 05 205, LLC Printed in USA