Fittings available in male straight, female straight, 45 and 90 designs for fast installation in all kinds of applications. Corrosion-resistant, die cast aluminum fitting with watertight seal (Deluxe Cord Connector ) protects connections from cable stress in damp applications. No special installation tools required. Non-corrosive, double-weave stainless steel mesh () supports the cable, absorbs stress caused by flexure and vibration, as well as controls arc of cable. Mesh readily expands for a wide range of cord diameters. CG610 Male Straight, Deluxe Cord Connectors Index Rugged, easy-to-install and available in a wide range of sizes our Flexcor Wire Mesh, Cable-Pulling, and Cable-s are engineered to take some of the strain off of you. Device Page Number K-2, K-3 Product Description K-4 Split Lace & Rod Mesh Termination K-5 s K-6 Grips K-7 Liquid-Tight Grips K-8 s Standard-Duty, Closed Mesh K-9 s Standard-Duty, Split Lace K-10 s Standard-Duty, Split Rod K-11 s Heavy-Duty K-12 s Service & Bus Drop K-13 s Fiber Optic K-14 Pulling Grips Junior- & Light-Duty K-15 Pulling Grips Medium-Duty K-16 Pulling Grips Heavy-Duty K-17 Pulling Grips Multi-Weave K-18 Pulling Grips High Strength & Fiber Optic K-19 Pulling Grips Slack K-20 Selecting Properly Sized Pulling & s K-21, K-22 Pulling & s Strength Information K-23 K-1
Bus/Service Drop Liquid-Tight Conduit Grip (page K-8) Bus/Service Drop Liquid-Tight Conduit Grip (page K-8) Medium/Heavy-Duty (pages K-16, K-17) Service Drop For assistance in selecting, see pages K-21 K-23. K-2
High Strength Pulling Grip (page K-19) Bus Drop Deluxe Cord Grip Strain Relief AIR Heavy-Duty Underground Pulling Grip (page K-17 K-3
Application are used to support cable or conductor after it has been installed, pull electrical cable or conductor into place, provide strain relief at the point of wiring connections. Flexcor devices protect cables, relieve stress, and prevent cable pull-out from fittings and terminations. Product Description Available in four different attachments. Load is distributed over entire length of grip and will not injure cable. Attachments Double Eye Single Eye Offset Eye Locking Bail Eye Grip Fittings Male Straight Female Straight Male 45 Male 90 Prevents pull-out or damage to cable due to constant motion or flexing. Also for Liquid-Tight, hose and box connections. Pulling Grips Rotating Eye Mesh Types Closed Mesh Split Lace Mesh Split Rod Mesh Assortment of rugged pulling grips available individually or in kits to make wire pulling easier. Product Description K-4 Available in three types and depends on availability of wire end.
Description Pulling Grips Junior-Duty & Light-Duty Junior-duty series grips are indispensable tools for electricians with small job requirements. They are used to connect insulated wire bundles to pulling tape or to pull wire or rope through conduit. Cable Diameter Mesh Approximate Catalog Number Range Length Break Strength* Junior-Duty, PJ25 0.250"-0.360" 5" 1,700 lbs. PJ37 0.370"-0.490" 7" 1,700 lbs. PJ50 0.500"-0.610" 8" 1,700 lbs. PJ62 0.620"-0.740" 10" 2,800 lbs. PJ75 0.750"-0.990" 10" 4,100 lbs. PJ100 1.000"-1.240" 12" 4,100 lbs. *To determine workload safety factor, divide approximate break strength by 5. See Page K-23 for strength information. Description Light-Duty grips are the most economical pulling grips for many applications, such as industrial plant wiring, and rewiring, and underground electrical pulls. Cable Diameter Mesh Approximate Catalog Number Range Length Break Strength* Light-Duty, Short Length, PL0501 0.500"-0.610" 11" 3,400 lbs. PL0621 0.620"-0.740" 11" 4,100 lbs. PL0751 0.750"-0.990" 13" 4,100 lbs. PL1001 1.000"-1.240" 14" 5,800 lbs. PL1251 1.250"-1.490" 15" 5,800 lbs. PL1501 1.500"-1.740" 16" 7,500 lbs. PL1751 1.750"-1.990" 18" 10,000 lbs. PL2001 2.000"-2.490" 19" 10,000 lbs. PL2501 2.500"-2.990" 19" 13,000 lbs. Light-Duty, Standard Length, PL0622 0.620"-0.740" 16" 4,100 lbs. PL0752 0.750"-0.990" 20" 4,100 lbs. PL1002 1.000"-1.240" 20" 7,500 lbs. PL1252 1.250"-1.490" 22" 7,500 lbs. PL1502 1.500"-1.990" 25" 7,500 lbs. PL2002 2.000"-2.490" 26" 10,000 lbs. PL2502 2.500"-2.990" 28" 13,000 lbs. PL3002 3.000"-3.490" 30" 16,200 lbs.. *To determine workload safety factor, divide approximate break strength by 5. See Page K-23 for strength information. Catalog Number Description Junior-Duty, Kit PJ1KIT Kit contains 1 each of PJ25, PJ37, PJ50, PJ62, PJ75, PJ100 Junior-Duty Light-Duty Short Length PJ1KIT K-15 Pulling Grips Junior-Duty & Light-Duty