Dial Indicator is used by being fitted to jig etc., while thickness gauge is held with our hand. Holding work piece between stylus and anvil, read the value directly. point moves to upward when lifting lever is pressed down, and contact point returns to zero when it is released. As operation is easy, it can measure for a short period compared with micrometer. There are 2 kinds of Dial mm, mm for both analog and digital. The stroke depends on size of work piece and a model is available to measure maximum thickness up to 0mm. This can be used for various thickness measurement such as paper, hair, rubber plate metal tube small molded components. Dial Thickness Gauge Suitable for measuring thickness and diameter of metal, lens, rubber, plastic, paper, felt, hair, pearl etc. in actual dimension. Ceramic contact point and anvil feature are superior for anti-abrasion and rust. In addition, there are steel FE type and AT type which rarely adheres with adhesion tape. As to shape of contact point and anvil, there are standard type and other various kinds. Measuring force of standard type is not more than 2.N as final pressure, low measuring force type of which final pressure is about 0.4N (about 40gf) is also available. SM-1P (Direct Reading ) SM-1D (Coaxial Revolution er) 2 SM-1 Standard type mm mm 1.1mm reading example 18. 4 64 unitmm All SM series equips ceramic contact point and anvils. SM-1 Series SM-1 SM-1LS SM-1LW SM-1-A SM-1-80g SM-1P SM-1FE SM-1AT SM-1D ±1 ±1 ±1 ±1 ±1 ±1 ±1 ±1 ±1 8 0-0-0 0-0-0 0-0-0 0-0-0 0-0-0 0-0.-1 0-0-0 0-0-0 0-0-0 Measuring metal work piece. The photo shows.9. 2. or less 2. or less 2. or less 2. or less Stop d 0.8±0.0 2. or less 2. or less 0.8 or less 2. or less Flat.2 Ball.2 Ball Flat Flat Flat Flat Flat Flat Flat Flat.2 Ball Flat Flat Flat Flat Flat Flat 10 10 10 10 10 10 10 10 1 81.8 SM-28 Measurement of up to mm thick mm mm φ. 1 φ 6 0. unitmm SM-28 Series SM-28 SM-28LS SM-28LW SM-28-A SM-28-80g SM-28FE 0-0-0 0-0-0 0-0-0 0-0-0 0-0-0 0-0-0. or less. or less. or less. or less Stop d 0.8±0.0. or less Flat.2 Ball.2 Ball Flat Flat Flat Flat Flat.2 Ball Flat Flat Flat 18
All SM series equips ceramic contact point and anvils. SM-114 12 SM-114 Insertion Depth 0mm mm mm 66 28 1 4 φ 0 1 8 unitmm SM-4 SM-4 Medium size Thickness Gauge 12 6 φ 8 mm mm 28 1 4 0 1 unitmm SM- Large size Thickness Gauge mm mm SM- 4.4 1.4 16 28 4 19 2 (2) 14 18 φ 6. 0. It can stand on its own with stand. This stand is standard accessories. unitmm SM-114 Series SM-114 SM-114LS SM-114LW SM-114P ±1 ±1 ±1 ±1 0-0-0 0-0-0 0-0-0 0-0.-1 2. or less 2. or less 2. or less 2. or less Flat.2 Ball.2 Ball Flat Flat Flat.2 Ball Flat SM-4 Series SM-4 SM-4LS SM-4LW 0-0-0 0-0-0 0-0-0. or less. or less. or less Flat.2 Ball.2 Ball Flat Flat.2 Ball SM- Series SM- SM-LS SM-LW 0-0-0 0-0-0 0-0-0. or less. or less. or less Flat.2 Ball.2 Ball Flat Flat.2 Ball 62 62 62 19
Carbide contact point SM-01 Symmetrical Dial mm mm Indication Range 1mm (Lifting ), =Solid Carbide SM-01L Continuous Dial mm 1mm, = Ceramic SM-02L mm 2mm, = Ceramic *Setting up standard point with block gauge is necessary to measure thickness 1mm and over. (0.) (0.) 8. 11 14 (99.4) φ8. 2 6 6. φ 4 6 6. (99.4) φ 4 9 Lifting of SM-01 18 0. unitmm SM-01L (2.) unitmm SM-02L (2.) unitmm SM-01 Series SM-01 SM-01LS SM-01LW SM-01L SM-02L 1* 22* ± 0-0-0 0-0-0 0-0-0 0-0-0 0-0-0 1. or less 1. or less 1. or less 1. or less 1. or less 8. Flat (Carbide) Ball (Carbide) Ball (Carbide) Flat (Ceramic) Flat (Ceramic) 8. Flat (Carbide) 8. Flat (Carbide) Ball (Carbide) Flat (Ceramic) Flat (Ceramic) 440 440 440 4 4 SM-1 By the lifting of the anvil, can be measured 0~0mm mm 0mm Indication Range mm (Lifting ) Upward Shockproof, = Ceramic *Setting up standard point with block gauge is necessary to measure thickness mm and over. Dial Swift Gauge SM-1 SM-1LS SM-1LW SM-1 Series Measuring Range 0 0 0 ±2 ±2 ±2 unitmm SFM-62 mm mm Upward Shockproof, = Ceramic 18 4 4 Lifting of 18 φ 4 21 9 116 ±0-0-0 ±0-0-0 ±0-0-0 0 Measuring Force 2.2 or less 2.2 or less 2.2 or less Flat.2 Ball.2 Ball Flat Flat.2 Ball 6 6 6 SFM-62 Measuring Range unitmm 0-0-0 Flat Flat 240
Dial Pipe Gauge :TPM-116 TPM-116 *Suitable for measuring thickness of pipe and curved plate etc. Radial thickness can be measured up to minimum diameter φ.mm. mm mm Upward Shockproof fixed type Edge of point 2.mm Flat Ball.mm TPM-618 TPM-61 mm mm replaceable type (Φ0.,Φ1.0,Φ2.0mm) mm mm replaceable type (option) :TPM-61/618 (6.1).4 (41.) (44.2) 14 (66) (9.9) unitmm 42. 2. Φmm Relation between diameter and Work inserting depth dia. Depth dia. 0. 1.0 2.0 2mm mm mm.0.0.0 Depth 22 9 unitmm mm The special order if the following hole diameter.mm. unitmm TPM-116 TPM-61 TPM-618 ±1 ±1 ±1 0-0-0 0-0-0 0-0-0 2. or less 1. or less 1. or less 2. Flat 1.6 Ball 1.6 Ball. Ball 0., 1.0, 2.0 replaceable.0 (.0,.0 replaceable)* 14 190 19 * and.0 are optional. Digital Pipe Gauge TPD-61J mm mm replaceable type TPD-618J mm mm replaceable type (option) :TPD-61J/618J All SM series equips ceramic contact point and anvils. Relation between diameter and Work inserting depth dia. Depth dia. 0. 2mm.0 1.0 mm.0 2.0 mm.0 Depth unitmm unitmm TPD-61J TPD-618J 1. or less 1. or less 1.6 Ball 1.6 Ball 0., 1.0, 2.0 replaceable.0 (.0,.0 replaceable)* 2 0 * and.0 are optional. 21
Conventional Digital Thickness Gauge Digital display for error-free reading SMD-40S2 mm mm 4.4 66.9. 6. φ Measurement force cannot be changed. Low measurement force is required, check a standard type. 2. Standard Type unitmm SMD-40S2 * φ Flat φ Flat SMD-40S2-LS φ Flat SMD-40S2-LW SMD-40S2-A φ Flat φ Flat * The quantizing error is not included. SMD-0S2 mm mm 2 18 1.4 11.8 φ 0 1 Standard Type unitmm SMD-0S2 * φ Flat φ Flat 400 SMD-0S2-LS φ Flat 400 SMD-0S2-LW 400 SMD-0S2-A φ Flat φ Flat 400 * The quantizing error is not included. Special order product of Dial Thickness Gauge / Digital Thickness Gauge 1. Instruct dimension and shape of anvil and contact point by referring to the figure in the right and P. 2. Instruct necessary measuring range.. In case that there is direction like blade type, instruct parallel or right angle based on graduation face as front face standard. 4. In case of requesting shape of anvil and contact point rather than figure in the right or change of measuring force, please contact our nearest branch for you. NE (needle) type This is top and bottom needle type(cylinder). Instruct diameter BL (blade) type This is top and bottom blade type(blade). Instruct width and thickness. KN (knife edge) type This is top and bottom knife edge type. Instruct width and angle. LD (large diameter flat) type This is top and bottom disc type(cylinder). Instruct diameter. 22
Standard Digital Thickness Gauge mm and mm graduation are available. mm model which can measure up to 1mm thickness as maximum by lifting anvil. SMD-40J mm mm SMD-0J mm mm SMD-6J mm 1mm Indication Range mm (Lifting of anvil) fixing screw PRINTER (Option) Printer for Digital Thickness Gauges Digital Mini-Printer SD-6P and connecting cable ZE-018. adjusting screw : SMD-40J : SMD-6J : SMD-0J 64.4 8.1. 4 φ 1 41 6.4 8.1 4 2 φ 2 99 144 2.9 18. φ 1 2. 1 2. 0 SMD-40J SMD-0J SMD-6J * 2 ( ) : Indicating Range* 1 1 () / 1.0 or less φ Flat 290 1.0 or less φ Flat 440 1. or less φ Flat 40 * 1 Indicating value in ( ) is a measuring range of digital sensor. * 2 The quantizing error is not included. SMD-6J-L Conversional type of : SMD-6J but without Adjustment. mm mm 8.1 SMD-1J Long stroke digital Thickness Gauge. mm 0mm Indication Range 2mm (Lifting of anvil) 28 66.9 6.. φ 2. (219) 18. 4 φ 2 Lifting of anvil 0 4 9 SMD-6J-L SMD-1J ( ) : Indicating Range* 1 * 2 0 (2) 1. or less φ Flat φ Flat φ Flat φ Flat 41 6 * 1 Indicating value in ( ) is a measuring range of digital sensor. * 2 The quantizing error is not included. 2
Constant Pressured Thickness Measuring Instrument Thickness measuring method for tested piece for physical test such as rubber, heat plasticity Elastomer, plastic film, cloth, textile, leathers are ruled in detail by JIS or ISO. PG/PF series are digital type thickness measuring instrument in compliance with these major standard. Stand type (fixed type) and frame type (handy type) are widely used for test & research dept., quality control dept. and manufacturing dept. Features Wide range of line-up complying with various standard of the field are available. High accuracy digital type with weight type for all the versions realizing stable static load, which is not got by analog type utilizing gears or springs. PG series uses micro-granite which is superior for abrasion resistance, chemical resistance, impact resistance in addition to high unstriated for measurable table. It can avoid scratches and stains for metal. Stainless steel is used for contact point and anvil (excluding partial model). Acid resistance, alkali proof, water resistance are improved. PG Series stand type PG-J JIS K 6 Method A PG- is the thickness measuring instrument compliant with A Law for measuring thickness which is standardized in JIS K 6 (ruled in physical test method general rule of rubber for vulcanized rubber and thermoplastic rubber.) This is sheet block compatible type which can measure both thickness of test piece hardness IRHD below and over by this one unit. point is diameter mm and pressure can be changed by only attaching and detaching weights. SD-6P (Printer = Option) :PG-01JPG-J ZE-018 (Connecting cable = Option) PG-J Power source is silver oxide batteries (SR-44) which is convenient to carry. This makes treating statistics of measured data possible with connected to optional printer SD-6P. point and measuring pressure can be changed. (However, it is not equivalent to standard ) Please refer to page 2 for specifications of each model. 0 1 φ 0 10 0 φ24.8 0 unitmm PF Series frame type PF-02J PF-11J :PF-01J/PF-02J -01φ -02φ2 :PF-11J18J 162-01 6-02 1 160..2 4 φ2 φ φ 1 2. unitmm 0 unitmm 24
Reference Standard Stand-type Frame-type JIS Measured Item (Mm) Measuring Range (Mm) Load () d (Mm) Measured Pressure PG-01J PF-01J K62-1996 Poly Vinyl Chloride Films For Agriculture 0.8N (80gf) or less PG-02J PF-02J K68-1994 Z102-1994 Z109-199 Ethylene / Vinyl Acetate Copolymer Films For Agriculture Polyethylene Films For Packaging Heat Shrinkable Plastic Films For Packaging 1.2.14mN (gf1gf) 14mN (gf1gf) PG-11J PF-11J K6400-199 Flexible Polyurethane Foam 0.6N (gf). 0.6kPa (.gf/cm 2 ) PG-J PF-J K61-199 Vulcanized Rubber 0.8N (80gf) PG-1J PF-1J K628-1999 K6-06 Rubber Coated Fabrics Rubber / For A Method (Less Than Irhd ) 0.8N (80gf) PG-14J PF-14J L86-0 Fusible Interlining Fabrics (Non Woven Textile) 0.94N (40gf) 16 2kPa (gf/cm 2 ) PG-1J PF-1J L86-1999 L96-0 Fusible Interlining Fabrics (Ordinary Textile) Woven Fabrics (Ordinary Textile) 2.N (240gf) 11. 2.kPa (240gf/cm 2 ) L18-1999 Knitted Fabrics (Ordinary Knit) PG-16J PF-16J L86-0 Fusible Interlining Fabrics (Ordinary Knitting Fabric) 0.4N (gf) 2.2 0.kPa (gf/cm2) L96-1999 Woven Fabrics (Crinose Textile) PG-1J PF-1J K60-199 K60-1994 Man-made Upper Material Of Shoes Leathers.80.1N (90gfgf) 49.01.1kPa (00gf/cm 2 ) PG-18J PF-18J K6-06 Rubber A Method ( Irhd And Over) 1 0.41N (44gf) ( IRHD and over) 22kPa (2.240.1gf/mm2) PG-J K6-06 Rubber A Method For Both (Less Than Irhd, Irhd And Over) 1 0.1960.08N (.9gf) 0.410.098N (44gf) (Less than IRHD) 2kPa (1.0.gf/mm2) ( IRHD and over) 22kPa (2.240.1gf/mm2 ) Aluminium alloy is used for material of contact point (including anvil) of PG-11J and PF-11J. point for other model are all stainless steel. PG-1 and PF-1 can be also used for IRHD below of JIS K 6 A law. PF series can be used by being fixed to stand (Option). Mounting example PF Series FM-18 Constant pressured thickness measuring instrument of the plate-cylindrical shape test piece (JIS K 6 method A) Hardness for IRHD below-or more of vulcanized rubber. unitmm Less than IRHD IRHD and over Graduatuon PGM-- ±2kPagf 22±kPa44gf mm 2mm mm PGM--8 ±2kPa1gf 22±kPa11gf mm 2mm 2
Thickness Gauge Special Product List point is spherical, the anvil is flat. LW type point. anvil with spherical. A type Upper and lower both φ flat. Adaptation models SM-1LS SM-28LS SM-114LS SM-4LS SM-1LS SM-01LS SMD-40S2-LS SMD-0S2-LS SM-1LW SM-28LW SM-114LW SM-4LW SM-1LW SM-01LW SMD-40S2-LW SMD-0S2-LW SM-1-A SM-28-A mm Measuring Range mm 0 0.2 Ball.2 Ball.2 Ball.2 Ball.2 Ball.2 Ball.2 Ball.2 Ball.2 Ball.2 Ball.2 Ball.2 Ball.2 Ball BallCarbide.2 Ball.2 Ball Flat Flat Anbil Form Flat Flat Flat Flat Flat Flat Flat Flat.2 Ball.2 Ball.2 Ball.2 Ball.2 Ball BallCarbide.2 Ball.2 Ball Flat Flat SMD-40S2-A Flat Flat SMD-0S2-A Flat Flat NEneedletype Upper and lower with needle type. SM-1NE SM-28NE SM-114NE SMD-40S2-NE 2 Flat 2 Flat 2 Flat 2 Flat 2 Flat 2 Flat 2 Flat 2 Flat SMD-0S2-NE 2 Flat 2 Flat BLbladetype Upper and lower with blade type. SM-1BL SM-28BL SM-114BL SMD-40S2-BL SMD-0S2-BL 1 t0./w4 t0./w4 t0./w4 t0./w4 t0./w4 t0./w4 t0./w4 t0./w4 t0./w4 t0./w4 KNbladetype Upper and lower with blade type. SM-1KN SM-28KN 1 t0./w4/ t0./w4/ t0./w4/ t0./w4/ SM-114KN SMD-40S2-KN SMD-0S2-KN t0./w4/ t0./w4/ t0./w4/ t0./w4/ t0./w4/ t0./w4/ LDflat disktype Upper and lower with a flat disk type. SM-1LD SM-28LD SM-114LD SMD-40S2-LD SMD-0S2-LD SM is Analog Type, SMD is Digital type. Parts & Accessories, of Symbol and Shapes Standard type LS type LW type A type φ Sφ.2 φ Sφ.2 Sφ.2 φ impossible replaces because of the adhesion. FE type φ flat steel SK4 Hardened SK4 Hardened AT type φ flat steel Ceramic Ceramic φ.2 Steel Ball Ceramic φ.2 Steel Ball φ.2 Steel Ball SK4 Hardened SK4 Hardened Specialized Coating